Microsoft Word - Manual Philco 6kg+hoja

Transcription

1 Instruction and installation manual Please read and save these instruction

2 2

3 Introduction Read this manual carefully as it offers practical advice to help you get the most from your washing machine. This «Instruction and Installation Manual» contains everything you need to know about the everyday running of your machine. Please refer to this manual for installation and maintenance instructions. The manual also contains information about possible working problems, advice about sorting clothes for washing, an explanation of label symbols and hints about how to remove stubborn stains. 1.- CONTROL PANEL 2.- LID 3.- DRUM 4.- DETERGENT DISPENSER 5.- PLINTH PANEL 6.- FILTER Table of contents page Safety measures 3 Setting up - Installation 5 Preparing the wash. Opening/ closing the drum 7 Detergent load 8 Electronically-controlled variable load- Fuzzy Logic 8 Description of controls 9 Special programmes 13 General recommendations 14 Troubleshooting 16 Washing hints 17 Safety measures This appliance meets the European Directives 2004/108/EC, 2006/95/EC which have been substituted respectively by 89/336/EEC, 73/23/EEC and subsequent modifications thereof. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. ATTENTION: FOR ALL CLEANING AND MAINTENANCE WORK Remove the plug. Turn off the water inlet tap after each wash. 3

4 The manufacturer fits all the machines with an earth connection. Ensure that the electrical installation has an earth connection and that it is connected; if not, call a qualified Service Center. The earth connection is essential for user safety as it eliminates the risk of electrical discharge. Power sockets should be in easily accessible places so that the washing machine can be unplugged in case of any problems. If the electric cable is damaged replace with an original set (cable and plug) supplied by the manufacturer or official aftersales service. note: In the event that it is necessary to replace the power cable, make sure that you comply with the following colour-code chart during the wiring: blue neutral brown phase Yellow-green earth The manufacturer accepts no responsibility for any damage to people or things resulting from the failure to comply with the appliance s installation and safety regulations. Do not touch the appliance with wet hands or feet. Do not use the appliance when bare-footed. Use extension cords only with extreme care. Do not use adapters or multiple plugs. Do not allow the appliance to be used by children or the infirm without due supervision. Do not pull on the power cord or the appliance itself to remove the plug from the socket. Do not leave the appliance outdoors or exposed to the atmospheric elements (rain, sun, etc.). Do not cover the appliance with cloth or plastic while it is working. Do not install the appliance in damp places or anywhere where it could be sprayed by the shower. Do not install the appliance on a surface which obstructs the space between the floor and the base of the machine. Keep all packaging out of the reach of children as it could constitute a health hazard. ATTENTION: DURING A WASH CYCLE THE WATER CAN REACH TEMPERATURES OF 90ºC. 4

5 Setting up - Installation Unpack the appliance. Remove the 4 screws (A) from both clamps and the 4 screws (B). Replace the 4 screws (A) and fit the trims provided (D). If your model offers this function: Position the protection sheet as shown in the diagram. 1.- Washing machine with wheel trolley. 2.- Washing machine without wheel trolley. ATTENTION: DO NOT TURN THE TAP ON The washing machine should be connected to the water mains via the new tube supplied with the appliance (inside the drum). Do not use the old tube for this purpose. Connect one end of the water inlet pipe with the elbow bend to the electrovalve (top rear part of the machine) and the other end to a tap or a plumbed-in 3/4" gas threaded connection. Place the washing machine close to the wall, ensuring that there are no bends or kinks anywhere in the tube. Hook the outlet pipe to the edge of the sink or preferably to a fixed drainage outlet of a diameter greater than that of the outlet pipe and at a height of min. 50 cm. and a maximum of 75 cm. from the floor. If necessary, use the curved accessory to attach and support the outlet pipe more securely. 5

6 If your model offers this function: To move the washing machine easily, turn the trolley lever to the right. Once you have finished moving the machine, return the lever to its original position. Level the machine by adjusting the front feet. a) Turn the nut clockwise to release the screw on the foot. b) Raise or lower the foot by rotating it until it stands firmly on the floor. c) Lock the foot in position by turning the nut anticlockwise until it comes up against the bottom of the washing machine. Check that the appliance is properly levelled. Check that the washing machine does not rock by trying to move two diagonally opposite top corners at the same time. If you move the washing machine from one place to another, you must level the feet again afterwards. Connect the machine. 6

7 Preparing the wash. Opening/ closing the drum ATTENTION: IT IS IMPORTANT TO MAKE SURE THAT THE DRUM IS CAREFULLY OPENED AND CLOSED, OTHERWISE THE MACHINE OR LAUNDRY COULD GET DAMAGED. ENSURE THAT THE DOORS FIT TOGETHER PERFECTLY AND ARE PROPERLY CLOSED. Loading 1. Open the washing machine lid. 2. Open the drum by pressing the (A) button with one hand while pressing down on the opposite door with the other. 3. Place clothes in the drum one item at a time, and without squashing. Do not exceed the load limits recommended in the programme table. An overloaded washing machine will not wash properly, and will leave clothing wrinkled. 4. To close the drum, place the doors so that the one with the (A) button is below the other and they fit together perfectly.

8 Detergent load II I Maximum Main wash washing powder Maximum pre-wash washing powder recommended Maximum Main wash washing liquid Maximum scenting agent The detergent dispenser is divided into 3 compartments:.- Compartment I is for the pre-wash detergent..- Compartment II is for the main wash detergent..- The compartment is for fabric conditioners, scenting agents and special additives such as starch, blueing, etc. The detergent dispenser has two reference marks:.- Recommended (lower reference mark). This indicates the recommended level for the pre-wash and main wash compartments..- Max. This indicates the maximum level, which should never be exceeded. Important: - Do not use liquid detergent for programs with a prewash cycle and/or timed start. - When the clothes present stains that need treatment with bleaches liquids products, you can proceed to their preliminary cleaning in the washing machine. For that: Introduce the bleach product in the "compartment II", and set the rinse program. Once finished set the programmer to the OFF position, add the rest of the laundry, and proceed with a normal was program. Electronically- controlled Variable Load Fuzzy Logic This machine has electronics that automatically process all stages of the wash to ensure exceptional results and at the same time save you time and money. Once a programme has been selected, the machine optimises the following elements depending on the wash load and type of fabric: - quantity of water and power consumption - wash time - rinse efficiency The washing machine also: - detects suds and increases the amount of rinse water if necessary - adjusts spin speed according to load distribution, thus forestalling any imbalance in the mechanism. 8

9 Description of controls H B2 G B1 C2 p V C1 A A PROGRAMME SELECTOR Use this control to select the desired wash programme. Turn the selector (it can be turned in both directions) so that the programme is opposite the reference indicator (p). The temperature selected will depend on the programme. (See the Programme Table). B1 SPIN/NO SPIN SELECTOR B2 DELAYED START KEY C1 COLD WASH C2 AQUA (SENSITIVE KEY) G H V p + DOOR LOCK LAMP START/PAUSE KEY DIGITAL Display The display s indicator system allows you to be constantly informed about the status of the machine CONTROL POSITION INDICATOR 9

10 programme COTTONS Programme table mod PTL 6105 programme for aprox. time min. max. temp. setting ºC spin speed rpm/min max. load Kg. washing powder load option keys C I II Cold + Aqua Fast coloureds with prewash display * Fast coloureds display * Fast coloureds display Delicate coloureds display MIXED SYNTHETICS DELICATES SPECIAL Fast coloureds display Delicate coloureds display Delicate coloureds display Wool display Hand wash display Rinse display Spin display Drain display Eco 20 display Rapid 44 display Rapid 30 display * Programme as per EN Technical data mod. PTL 6105 Mains voltage V. 50Hz. Wash power rating Spin Power rating Pump Motor Power rating Heating element power rating Max. Power input Mains Fuse Amp. rating 175 W. 340 W. 30 W W W. 10 A. Water pressure 0,05-0,8 Mpa Water consumption *prog. EN L. Energy consumption *prog. EN ,732 Kw. IMPORTANT: Do not use liquid detergent for programs with a prewash cycle and/or time delay. PREPARING THE WASH CYCLE 1.- Once the washing is loaded, ensure that the drum doors are properly closed Add detergent and additives, not exceeding the maximum level indicator..- detergent for pre-wash I.- detergent for wash programme II.- fabric conditioner

11 SELECTING THE DESIRED PROGRAMMES AND OPTIONS 3.- Turn the programme selector (A) to the desired programme. 4.- Press the key or keys for any options desired (C1, C2 )..- It is advisable to select the required options before pressing the Programme Start key (H)..- Remember that if the programme has already passed the stage at which an option is activated, that option will not be implemented. C1 Cold wash key By pressing this button it is possible to transform every programme into a cold washing one, without modify other characteristics (water level, times, rythmes, etc..). Curtains, small carpets, man made delicate fabrics, non coulor fast garments can be safely washed thanks to this new device. C2 Aqua (sensitive key) Thanks to the new SENSOR ACTIVA SYSTEM, by pressing the key it is possible to run a special washing cycle applicable to all programs and types of fabric, caring for their fibres and the delicate skin of the users who use them. Taking on much more water, together with the new combined action of drum rotation cycles and taking on and discharging water allow you to obtain perfectly clean, rinsed clothes. More water is used in the wash to dissolve the detergent completely, ensuring an effective washing action. The water in the rinses has also been increased to eliminate all trace of detergent in the fibres. This function has been specifically studied for people with delicate, sensitive skin, who can suffer irritation or allergy from the slightest detergent residue. It is also advisable to use this function for children's clothes and delicate fabrics in general, especially for washing bathrobes, whose fibres tend to retain detergent. This option is not available for the wool program. 5.- Select spin speed if required (B1) B1 spin speed Once the programme has been selected, the maximum spin speed allowed for that programme appears on the display. Pressing the spin button will reduce the speed by 100 rpm each time the button is pressed. The minimum speed allowed is 400 rpm, or it is possible to omit the spin by pressing the spin button repeatedly. 6.- To start the programme, once options have been chosen, press the key H. The washing machine will begin to operate. If you wish to cancel the option you have selected, press the key again. (The pilot light will go off). B2 Time delay button This button allows you to pre-programme the wash cycle to delay the start of the cycle for up to 24 hours. To delay the start use the following procedure: Set the required programme. Press the button once to activate it (h00 appears on the display) and then press it again to set a 1 hour delay (h01 appears on the display); the pre-set delay increases by 1 hour each time the button is pressed, until h24 appears on the display, at which point pressing the button again will reset the delay start to zero. Confirm by pressing the START/PAUSE button (the light on the display starts to flash). The countdown will begin and when it has finished the programme will start automatically. It is possible to cancel the delay start by taking the following action: Press and hold the button for 5 seconds until the display will show the settings for the programme selected. At this stage it is possible to start the programme previously selected by pressing the START/PAUSE button or to cancel the process by setting the selector to the OFF position and then selecting another programme. Cycle duration (V) When a programme is selected the display automatically shows the cycle duration, which can vary, depending on the options selected. Once the programme has started you will be kept informed constantly of the time remaining to the end of the wash. 11

12 Door lock light (G) Once the START/PAUSE button has been pressed the light first flashes then stops flashing and remains on until the end of the wash. 2 minutes after the end of the wash the light goes off to show that the door can now be opened. Cancel-change programs Once you have started a program, and wish to change or cancel it, you should proceed in the following manner, - Put the program selector in the OFF position. At that instant, you have cancelled the program and can if you wish to do so, select a new one. - Select the new program. - Click the key (H) again. The washing machine will perform the new selected program. Programme pause It is possible to momentarily stop the wash programme so that more washing can be added, and to do so, proceed as follows: - Hold down the (H) key until the option key lamps begin to flash and the time remaining indicator display, and pilot lamp lights up. - When the Door Lock lamp goes out (after approx. 2 minutes), open the door and add the desired washing. - Correctly close the doors of the drum and the outer cover. - Press the key H, and the washing machine will continue with the programme. When the programme has been completed, the message "END" will appear in the indicator display, Wait until the Door Lock lamp (G) goes out (after approx. 2 minutes) To remove the washing, set the programme selector to the OFF position, before opening the washing-machine lid and the drum doors. 12

13 Eco 20 Eco 20 :This innovative programme,allows you to wash different fabrics and colours together,such as cottons,synthetics and mixed fabrics at only 20 ºC and provides an excellent cleaning performance.consumption on this program is about 40% of a conventional 40 ºC cottons wash.

14 General recommendations CLEANING AND MAINTENANCE OF THE MACHINE Do not use abrasives, spirits or solvents when cleaning the exterior of the washing machine. It is sufficient to use a damp cloth. The washing machine requires very little maintenance. Drying the rubber seal of the drum. Cleaning the dispenser and its compartments. Cleaning the filter. Cleaning prior to removals or when the machine is to stand idle for long periods. To help conserve the washing machine, dry the rubber seal and leave the door open when the cycle ends. CLEANING THE FILTER The washing machine comes with a special filter, located behind the machine s front plinth panel, that collects larger objects (coins, buttons, etc.) which could even block the pump. It is advisable to clean the filter whenever the machine fails to rinse the clothes as well as it should or when it fails to drain properly. When it is necessary to clean the filter, proceed as follows: Use a basin to collect the water coming out. Remove the filter and clean it. Once the filter is clean, replace it by following the abovementioned pro in reverse. 14

15 CLEANING THE DETERGENT DISPENSER AND ITS COMPARTMENTS.- It is advisable to clean the three compartments of the detergent dispenser (pre-wash, wash, and fabric conditioner) from time to time. To do this, remove the detergent dispenser and after cleaning it, fit it back in place. To remove and fit the detergent dispenser, follow the steps indicated in the images. A removing.- Press button A.-Hold down the button and pull the detergent dispenser outwards II I.- Remove the dispenser and clean it.- In the case of the pre-wash (I) and wash (II) compartments, it is advisable to remove any dried-in remains of detergent which obstruct the flow of the detergent to the drum. S.- In the fabric conditioner compartment, the trap (S) located at the rear part of the dispenser should be removed by pulling them out. Remove any solid residue which could block the holes in the compartments. B fitting.- Fit in the tabs as shown C.- Push the detergent dispenser towards the housing (C) in the door until the tab clicks into place. 15

16 Troubleshooting FAULT CAUSE SOLUTION 1.- No programme works The appliance is not plugged in. The general switch is disconnected. There is no electricity. The fuses in the electric installation are damaged. The door is open. Plug it in. Activate the general switch. Check. Check. Close the door. 2.- The appliance does not load water See causes for 1. The tap is turned off. 3.- The water does not drain The filter is clogged. The outlet pipe is bent. 4.- The spin function does not work 5.- Strong vibrations during spin cycle 6.- The high-speed spin does not work 7.- Display will show error nº 0,1,5,6,7,8,9,12,13,15,16 The washing machine has not yet drained the water. The Spin Exclusion option is activated. The washing machine is not correctly levelled. The anchoring device for transport has not been removed. The wash load is not evenly distributed. The wash load is not evenly distributed within the drum. Check. Turn on the tap. Check the filter. Straighten the outlet pipe. Wait a few minutes for the washing machine to drain. Enable the spin option. Adjust the feet. Remove the transport support. Distribute it evenly. Distribute the wash load evenly in the drum. Contact technical service. 8.- Display will show error nº 2 Machine does not fill with water Check that water inlet tap is open. 9.- Display will show error nº 3 Water does not empty from machine 10.-Display will show error nº 4 Too much water in machine. Check that outlet is not clogged Check for kinks in outlet tube. Shut off water tap. Contact technical service If the problem or malfunctioning persists, disconnect the machine, turn off the tap and do not try to repair. For all repairs contact an Official Technical Assistance centre (consult the European guarantee sheet) and always insist on the use of original parts. Failure to do so may compromise the safety of your machine. When contacting a Technical Assistance Centre always refer to the model (see also control panel) and the registration and serial numbers indicated on the plate at the bottom front of the machine behind the plinth panel or on the guarantee certificate. That is to say, everything that appears in the box. Providing this information will ensure a faster and more efficient service. 16

17 Washing hints Hints on the most economical, most environmentally friendly way to use your washing machine. HINTS ON USING YOUR WASHING MACHINE Wait until you have a full load before using the machine: this will avoid the use of more water and power than necessary. We recommend using the full load capacity: this could save you up to 50% in power consumption. Wash a single full load rather than two light loads. WHEN IS PRE-WASHING NECESSARY? Only when washing heavily soiled clothes. With clothes that are not especially dirty, you can save between 5 and 15% by not using this option. WHAT WASH TEMPERATURE SHOULD I USE? Applying a stain remover before placing clothes in the machine will eliminate the need for wash temperatures of more than 60 ºC. When loading a wash into the drum, we recommend that you: For specially delicate garments we recommend the use of a protective net. Empty all pockets and ensure that they do not contain metal objects (paperclips, safety pins, pins, coins,etc.). Fasten pillow slips, close all zips and fastenings, and tie any loose ribbons or belts from dresses. Remove all runners (metal and plastic) from curtains and net curtains. We recommend that the ribbon be gathered into a ball and tied with its own cord. Unfold all items to be washed. Be careful not to exceed the recommended load for each programme. When washing rugs, bedspreads and other highly absorbent items, cancel the spin option. In order to be able to wash woollens in the washing machine they must carry the Pure New Wool symbol as well as the information does not become matted or machine washable. If possible, do not wash only towels. Mix them with your regular washing. Ensure that no item becomes trapped between the drum doors. LABEL SYMBOLS Labels are usually sown into the collar or side seams. The symbols which appear on them indicate the following: Maximum WASH temperature. Appropriate and inappropriate washing methods. Appropriate and inappropriate washing products. The symbols are as follows: WASH Washing instructions always appear as a basin with different indications: Do not wash. Can be washed both by hand or in the washing machine. The figures in the basin indicate the maximum wash temperature. Hand wash only. When the hand is half submerged in the water, this means that the item should be tumbled only gently during washing. If it is fully submerged in the water, this means that the garment should only be washed by hand. The line under the basin means that the item should be washed on a gentle cycle. Do not spin. BLEACH Bleach is widely used to whiten fabrics, although in some cases it can cause irreparable damage. There are various symbols which refer to its use. Bleach can be used. Do not use bleach. 17

18 Please record the following information: Model Serial No. Name of distributor Date of purchase The manufacturer reserves the right to make any technical modifications due to product improvement. No prior notice will be given.if you have any enquiry,please contact our after-sales department and forgive for any inconvenient. All information is subjected to English version. /F, Shing Dao Industrial Building, 232 Aberdeen Main Road,Hong Kong : Service Hotline :

19 232 /F, Shing Dao Industrial Building, 232 Aberdeen Main Road,Hong Kong : Service Hotline :

20 This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE). WEEE contains both polluting substances (which can cause negative consequences for the environment) and basic components (which can be re-used). properly all pollutants, and recover and recycle all materials. Individuals can play an important role in ensuring that WEEE does not become an environmental issue; it is essential to follow some basic rules: - WEEE should not be treated as household waste; - WEEE should be handed over to the relevant collection points managed by the municipality or by registered companies. In many countries, for large WEEE, home collection could be present. In many countries, when you buy a new appliance, the old one may be returned to the retailer who has to collect it free of charge on a one-to-one basis, as long as the equipment is of equivalent type and has the same functions as the supplied equipment.

21 2

22 3

23 4

24 5

25 6

26 7

27 p H B2 G B1 C2 V C1 A A B1 B2 C1 C2 G H V P 8

28 PTL 610 E Amp. rating V. 50Hz. 175 W W. 30 W W W. 10 A. 0,05-0,8 Mpa * EN L. * EN ,732 Kw. 9

29 10

30 11

31

32 13

33 III S C 14

34 15

35 16

36 /M