REMOTEAIRPRO说明书中英文版

REMOTE AIR PRO Product Manual

Welcome to your new REMOTE AIR PRO

REMOTE AIR PRO Whatʼs Included

Instruction manual 1 Motor Installation The motor is mounted on 19 mm or 15 mm rods. For 15 mm rods use the included 19 to 15 mm rod adaptor. 2 Connecting Motors When using PD3-P1 (Single Channel): 1.Connect the D-Tap power cable 6-pin aviation locking plug directly to the PD3-R REMOTE 12 ~ 18V input. 2.Then connect the D-Tap plug to a pro battery or similar power source with a D-Tap output. When using the PD3-P2 (Dual Channel): 1.Connect the motor cable (6-pin) from the PD3-R REMOTE 12 ~ 18V connector to the PD3-M REMOTE12 ~ 18V connector. 2.Connect the D-Tap to 6-pin aviation locking plug to PD3-M REMOTE12 ~ 18V and connect the D-Tap plug to a pro battery or similar power source with a D-Tap output. When using PD3-P3 (Triple Channel): 1.Connect one Motor Drive Line Cable to the PD3-R REMOTE12 ~ 18V connector and the PD3-M1 REMOTE12 ~ 18V connector. 2.Connect second Motor Drive Line Cable to the PD3-M1 REMOTE12 ~ 18V connector and the PD3-M2 REMOTE12 ~ 18V connector. T 3.Connect the D-Tap to 6-pin plug to the PD3-M2 REMOTE12 ~ 18V connector and Then connect the D-Tap plug to a pro battery or similar power source with a D-Tap output. 3 Connecting Control Unit Depending on which device you are using iphone 6/6s iphone 6 Plus / 6s Plus / ipod touch, select the correct clamp that fits your device. To attach or remove the device clamps loosen or tighten the thumb wheels on either side of the focus knob. Rotate to the left to tighten or to the right to loosen. Slide you device in from the top and then tighten the clamp. The clamp is lined with a soft rubber to prevent scratches to your device.

4. Installing the Antennas Three antennas are included in the package. Install one on the hand control unit. Install one on the PD3-R Receiver Motor. The third antenna is an extra. 5. Powering On To power on the Hand Controller Unit, press the ON / OFF button on the bottom of the unit for two seconds until the screen lights up. To power on the motor, press the ON / OFF button on the bottom for two seconds until the indicator lights up. 6. Adjusting channel When you power on the Hand Control Unit the OLED display on the back shows status information. The fist line displays the current channel. The channel on the Hand Control Unit MUST match the channel on the PD3-R Receiver Motor. If they do not you can short press the OFF / ON Channel on either unit multiple times until the channel number matches. Hand Control Unit OLED Display Information: 2.4G 2.4GHZ wireless network Channel Signal Level TX RX Shows current Channel in use, short press on OFF/ON Channel button to change channel It displays the signal strength of the Hand Control Unit and the receiver when interworking The controller battery charge remaining percentage Receiver voltage 5V or 0V OLED screen display USB5V in the upper right corner of the controller output; 5V means USB5V output is ON; 0V means USB5V output is OFF 7. Remote Air App Download App from the Apple App Store (Search for Remote Air) Make sure you have the latest version of ios and Bluetooth enabled on your device Make sure that your motors and the hand control unit are powered on and on the correct channel. Run the app. If you have your motors and Hand Control Unit on it will enter into the main menu. To confirm that your device is communicating with Remote Air Pro the indicator lights at the bottom of the Hand Control Unit will turn from red to green. 8. Calibrating Lens Make sure that your motors are properly and securely attached to your camera rig and in contact with your lens. Long press (3 seconds) the "AUTO" button on the top left side of the hand control unit. You can also press the AUTO button that is located on the bottom right side of the main menu on the Remote Air App. When using PD3-P2 or PD3-P3 the multiple motors will simultaneously self-test. 9. App Control Interface The main control interface of the app contains three columns that represent the three channels. (ZOOM, IRIS, FOCUS) In order to enable control of these channels you can touch on the words ZOOM, IRIS, or FOCUS. When they appear gray it indicates that the channel is turned on and active in the app. When the channels are active you can control the motors by simply sliding your fingers in the respective column. When they appear black, then the channel is OFF and cannot be controlled via the app. (To learn about the functions of APP control interface, go to the bottom right corner APP SET, click HELP to view.)

10. Types of Control Methods Focus Wheel Control: In order to use the focus wheel you must either not be using the app and be in single channel mode OR if synced with the app you must have the focus channel turned off in the app. App control interface: When the ZOOM, IRIS, FOCUS channels are highlighted grey in the app interface, it means you can use the touch screen to control the motor that corresponds to the different channels. Motor Button Functions Button ON/OFF CHANNEL SPEED Function Description Power ON: Press for two seconds until the indicator light turns on Power OFF: Press for two seconds until the indicator light turns o Short press button to switch channels Speed mode and channel switching (see table below for reference) ANTENNA Antenna connector REMOTE 12~18V Signal and power supply common interface, supports power supplies with 12 ~ 18V voltage range Motor channel switching table Fast and Short Press Motor SPEED Button Motor Channel Indicator Light Color Channel in App R1 RED FOCUS G2 GREEN ZOOM B3 BLUE IRIS Y4 Yellow Channel 4 C5 Cyan Channel 5 P6 Purple Channel 6 Motor Speed Mode Switching Fast short press motor SPEED key Motor Speed LED Blinking Frequency Fast (High torque) Fast Flashing Medium (moderate torque recommended for FOCUS) Slow (less torque, it is recommended for ZOOM) Slow Flashing Steady

Hand Control Unit Controller Buttons Description Button Function Instructions ON/OFF CHANNEL Turn ON/OFF Changing Channel Press for two seconds to turn ON / OFF controller Short press once Automatic Calibrating Press 3 seconds till the lens is rotating then let go AUTO Motor forward and reverse switching Continuous press 5 times Manually set the (AB point) Set Cancel Press 2 times: first short press, then long press and hold, turning the handle while holding long press to set AB point, after the completion then release Continuous 2 short press to cancel previous setting 5V 5Vcharging input ANTENNA Antenna connector Hand Control Unit Status Indicator Lights Indicator RED GREEN PURPLE GREEN Status Unit is powered on Unit is powered on and synched with your device via Bluetooth Unit is charging (Use aviation locking plug to USB cable) Unit is synced via Bluetooth and being charged at the same time

Additional information 1) When the iphone / ipod touch is running low, you can use the included Lightning to USB cable to connect the device to the Hand Control Unitʼs USB 5V charging output interface. 5V will show on the top right corner of the OLED display on the hand control unit when itʼs active. When the Hand Control Units internal battery becomes low it will shut the 5V output off to save battery. When this happens the top right hand side of the OLED display will show 0V. The Hand Control Unit has a built-in 6000mAH battery. This about twice the capacity of the iphone 6 Plus, three times the capacity og the iphone 6 and about five times the capacity of the ipod Touch. This data is only for reference only. 2) REMOTE AIR PRO is equipped with three different size lens pitch gears (0.4M, 0.5M, 0.6M), Choose the right size that fits your lens gear pitch. Use the included 3mm hex key to remove and re-attach the gears. 3) Emergency stop function: If you run into a situation where the motors are behaving erratically. Short press the ON / OFF button on the bottom of the motor and it will immediately stop (note: emergency stop on PD3-R and all the connected motors will stop as well.). 4) When you launch the app it will automatically search and sync with the Hand Control Unit. If you turn off the Hand Control Unit during use you will also have to re-launch the app. 5) Power Supply and Charging - When the USB5V output is not in use the battery life is up to 60 hours. - The Hand Control Unitʼs OLED screen displays the percentage of the remaining battery life. - When the Hand Control Unit is running low, you can use a power bank to charge via 5V IN - When the unit is not in use for extended periods of time it is recommended that you check the battery at regular intervals. Check to ensure that the battery has enough power. Keeping the battery low or completely drained for extended periods of time can decrease the life span of the batteries. 6) Equipment Maintenance: Whenever possible strive to store the Remote Air Pro in a relatively dry environment. When electronic components are exposed to humidity greater than 60% it becomes easier for them to develop moisture or mold and it can cause damage. If the unit will not be in use for an extended period of time make sure you store it in the waterproof case they shipped in and with the packet of desiccant that was included. This will ensure a long and trouble free life.

Important Please read this document, master REMOTE AIR PRO usage,before you first use your REMOTE LIVE. Learn more You can find more information, watch demos, and learn even more about REMOTE AIR PRO features at www.pdmovie.com/remoteairpro/. Support REMOTE AIR PRO enjoy free upgrade program and one year of hardware warranty period, you can get these services from PDMOVIE dealer. Contact WEB:www.pdmovie.com MAIL:pd@pdmovie.com PDMovie is distributed by ikan. ikan Corporation 11500 S. Sam Houston Pkwy West Houston, TX 77031 TEL:+1.713.272.8822 www.ikancorp.com

REMOTE AIR PRO

2.4G 2.4GHZ Channel Channel Signal Level TX RX 5V or 0V OLED USB5V 5V USB5V 0V USB5V