未命名 -1

Transcription

1 TTL 锂电机顶闪光灯 Pioneering TTL Li-ion Camera Flash For Sony 深圳市神牛摄影器材有限公司 GODOX Photo Equipment Co., Ltd. 地址 /Add: 深圳市宝安区福永镇福洲大道西新和村华发工业园 A 栋 Building A, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong Town, Baoan District, Shenzhen 580, China 电话 /Tel: (806) 传真 /Fax: 邮箱 / godox@godox.com V86S0-00 Made In China 在使用本产品之前 : 请先仔细阅读本手册, 以确保您能安全使用 请保存好本手册以备将 来查询参考 Before using this product: INSTRUCTION MANUAL 说明手册 中英文双语 / Chinese English Bilingual Please read this user manual carefully in order to ensure your safety and the proper operation of this product. Keep for future reference.

2 前言 安全须知 感谢您购买神牛产品 该型号机顶闪光灯适用于 SONY 系列相机, 兼容 TTL 自动闪光 使用 TTL 闪光灯, 您将获得更简单的拍摄体验, 在光线变化复杂的情况下, 可以自动获得准确的闪光曝光, 拍摄轻松自如 产品特点突出表现在以下几方面 : GN60 (m ISO 级调光 (/~/8) 专业锂电, 优质体验 000mAh 锂聚合物电池, 全功率 650 次闪光,.5 秒快速回电, 便携性无与伦比 兼容索尼相机 TTL 支持 TTL 自动闪光, 可作为无线多灯闪光系统的主控或从属单元, 拍摄更简单快捷 点阵液晶屏显示直观, 操作更加简易 内置.G 无线传输收发一体, 超远距离, 创意无限 无线功率遥控触发选购 FT-6S 遥控器, 可对离机闪光灯进行无线功率调节等参数设置, 同时触发引闪 功能齐全, 无限享用支持手动和频闪闪光模式, 高速同步 / 第二帘快门同步 / 闪光曝光补偿等 TTL 功能 光学研究, 输出稳定高速连闪, 每次输出亮度和色温连续一致 ( 5600±00K), 光线均匀分布 固件升级, 兼容无忧跟随原厂相机步伐, 可对软件进行再升级 请勿让本产品淋雨或受潮, 以免发生火灾或触电 本产品内部有高压元件, 切勿自行拆解或维修 如果接触产品内部的高压电路, 可能会发生触电 需要修理时, 请送往指定地点进行专业维修 在使用过程中, 如果本产品由于跌落 受到挤压或遭受强烈冲击而造成外壳破裂的, 请勿继续使用, 以免因接触到内部电子元件而受到电击伤害 请勿在近距离将闪光灯头正对人眼闪光 ( 特别是婴儿的眼睛 ), 否则可能会在短时间内造成视力障碍 在使用闪光灯拍摄婴儿时, 建议闪光灯距离婴儿至少 米以上, 也可以使用反射闪光来减少闪光可能对视力造成的伤害 请勿在化学品 可燃性气体或其他特殊物质附近使用闪光灯, 这些物质在特殊情况下可能对闪光灯发出的瞬间强光敏感, 有可能导致火灾或电磁干扰 在这些场合下, 请注意相关警告标识 请勿将本产品放置在超过 50 摄氏度的环境下, 否则可能对元器件造成损坏 本产品不能防水, 在雨天及潮湿环境下请注意防水

3 Pioneering Li-ion Camera Flash TTL 锂电机顶闪光灯 Pioneering TTL Li-ion Camera Flash 本说明书中使用的约定 此使用说明书中的操作步骤假定相机和闪光灯的电源开关已开启 参考页码由 ( 第 ** 页 ) 表示 此使用说明书中使用以下警告符号 : 该 小心 符号表示避免出现拍摄问题的警告 该 注意 符号提供补充信息 目录 前言安全须知部件名称机身控制面板 LCD 液晶显示屏套装标配物品单灯标配物品可选购附件电池装卸闪光灯电源管理闪光模式 : TTL 自动闪光模式闪光曝光补偿高速同步第二帘快门同步闪光模式 : M 手动闪光闪光模式 : Multi 频闪闪光无线闪光拍摄 : 光学传输无线设置设置主控闪光灯的闪光模式设置通讯频道无线闪光拍摄 : 无线电 (.G) 传输无线设置设置主控闪光灯的闪光模式设置通讯频道 TTL: 全自动无线闪光拍摄 M: 动无线闪光拍摄 Multi: 手动无线闪光拍摄其他应用外置无线控制功能同步插孔触发自动辅助对焦灯反射闪光创建眼神光 ZOOM: 设置闪光覆盖范围并使用广角散光板 C.Fn: 设置自定义功能保护功能规格参数故障排除指南固件升级兼容相机列表维护保养

4 LCD液晶显示屏 部件名称 () TTL自动闪光 Zoom : 变焦显示(第页) 焦距(闪光覆盖/第页) : 自动 : 高速同步 : 手动(第页) 09 (第0页) TTL : TTL自动闪光 距离指示显示 : 闪光曝光补偿(第0页) 闪光曝光补偿量 显示屏将只显示当前应用的设置 08 在功能按钮至功能按钮上方显示的功能(如< 机身 < 0. 眼神光板 08. 热靴 0. 内置广角散光板 09. 点阵液晶显示屏 0. 闪光灯头 0. 固定旋钮 0. 无线传感器. 电池仓 05. 辅助对焦灯. USB端口 06. 同步插孔. 从属单元状态指示灯 SYNC >和 >)根据设置的状态发生变化 当操作按钮或拨盘时 液晶显示屏点亮 ()M手动闪光 M : 手动闪光 07. 无线控制插座 手动闪光输出 RST 6 ()Multi频闪闪光 Multi : 多重(频闪)闪光 闪光次数 闪光频率 控制面板. <MODE>闪光模式选择按钮 /锁定按钮 5. < >无线按钮 9. < >试闪按钮/回电指示灯 0. 功能按钮. 功能按钮 6. 调节旋钮. 功能按钮 7. <SET>设置按钮. 功能按钮 8. ON/OFF电源开关

5 可选购附件 ()无线电传输拍摄/光学传输无线拍摄 可搭配本公司以下摄影附件使用 以获得最佳的拍摄效果和使用体 主控单元 验 XT-S无线引闪器 FT-6S功率遥控器 迷你柔光箱 反光 闪光模式 板 蜂巢 色片 束光布等 Gr : 组闪光 : 无线电传输无线拍摄 : 光学传输无线拍摄 闪光组 频道 从属单元 电池 特性 : 从属. 本品采用锂聚合物电池 支持反复充放电500次 使用寿命长. 安全可靠 内置电路有过充保护 过放保护 过流保护 短路保护. 使用标配电池充电器只需.5个小时左右 注意事项. 避免正负极短路 套装标配物品. 电池没有防水功能 不要把电池浸泡在雾 水中 灯体 锂电池 电池充电器 充电器电源线. 放置于儿童不易接触的地方 5 微型底座 6 保护包 7 说明书. 电池充电不要放置超过小时 5. 电池应放置于凉爽 干燥及通风的地方存储 单灯标配物品 6. 电池不要靠近和放置于火中 灯体 5 微型底座 6 保护包 7 说明书 7. 电池使用报废后请按当地的规定处理 8. 如果电池超过个月不使用 请对电池进行满电充电 装卸电池 用您的拇指按电池仓盖 然后滑动电池仓盖将电池 仓盖打开 打开电池仓盖 安装电池 按电池指示方向将锂电池 插入电池仓 直至扣件卡 住 关闭电池仓盖即可 5 6 拆卸电池 打开电池仓 往右轻推扣 件直至锂电池弹出

6 电池电量指示 把锂电池正确安装在闪光灯上 即可给闪光灯供电 使用时请查看闪 光灯屏幕上电池图标 即可随时掌握电量状态 电池电量显示 意义 格 满电 格 中电 闪光模式 TTL自动闪光模式 该闪光灯有TTL自动闪光 M手动闪光 Multi频闪闪光三种模式 在TTL模式下 相机的测光系统会侦查从主体反射回来的闪光照明 从而自动调节闪光输出量 使主体和背景得到均衡曝光 支持曝光补 偿 高速同步 第二帘快门同步 光圈预览造影闪光等功能 按下<MODE>模式选择按钮 三种闪光模式将会依次出现在液晶 屏上 格 低电 无格 电量少 请及时充电 无格闪烁 电量即将用尽 此状态不支持闪光灯工作 注 此状态请尽快(0天内)充电 才可使用或放置 TTL模式 通过按<MODE>模式选择按钮 将闪光灯设置为<TTL>, 可以使闪 光灯进入TTL模式 半按相机快门按钮进行对焦 光圈值和有效闪光范围将会显示在显 示屏上 在快门释放前的瞬间进行一次预闪 闪光灯接收相机信息进行主闪 装卸闪光灯 光 安装闪光灯 滑动闪光灯固定座使其完 全插入相机的热靴插座 闪光曝光补偿 该闪光灯可以在±档间以/档为增量调节闪光曝光补偿 由于环境 的需求而需要微调TTL系统时 这个功能非常有用 设置闪光曝光补偿 拧紧闪光灯 旋转固定座上的锁定旋 按下功能按钮< 令屏幕显示< > >图标 并 且闪光曝光补偿量被突出显 示 钮 直到锁定闪光灯 取下闪光灯 旋转固定座上的锁定旋钮 设置闪光曝光补偿量 转动调节旋钮设置曝光补 偿量 "0."表示/档 "0.7"表 直到闪光灯解除锁定 示/档 要取消闪光曝光补偿 将 闪光曝光补偿量设为 "+0" 电源管理 ON/OFF电源开关控制该产品的打开和关闭 长时间不使用时请关 闭电源 本产品设计有电源自动关闭功能 作为主控单元在长时间 约秒 无人操作时 闪光灯会自动关闭 半按快门按钮或机身任 意键唤醒 作为从属单元在60分钟 或者选择0分钟 无任何操作 时 闪光灯会进入休眠状态 此时可按机身任意键唤醒 C.Fn 离机使用时 建议通过自定义功能使 自动关闭电源 无效 (C.Fn-APO 第页 C.Fn 从属单元自动关闭电源计时器 出厂默认设置为60分 钟 也可自定义选择0分钟 (C.Fn-SvAPOT 第页 按下< SET >设置按钮 确 定闪光曝光补偿 高速同步 使用高速同步(FP闪光) 您可以在所有的快门速度下同步使用闪光 灯 高速同步模式下 使用光圈优先对人像进行填充闪光时特别方 便 高速同步设置由SONY相机快门决定 请查看相机说明书 使用高速同步 快门速度越高 有效的闪光范围就越小 在高速同步模式下 无法设置频闪闪光 连续高速同步闪光5次后 闪光灯热保护功能可能会被激 活 - 0 -

7 第二帘快门同步 闪光模式 Multi 频闪闪光 使用慢速快门 您可以在被摄物体后创建一条光线轨迹 在快门关闭 前的瞬间闪光灯闪光 使用频闪闪光 可以发出一系列快速的闪光 它可以在一张照片上拍 在SONY相机机身设置中 选择 Rear闪光方式 摄移动物体的多个图像 您可以设置闪光频率(每秒的闪光次数 以 Hz表示) 闪光次数和闪光输出 闪光模式 M 手动闪光 您可以在/8功率至/全功率间以/档为增量设置闪光输出 为 获得正确的闪光曝光 请使用手持的闪光测光表确定所需的闪光输出 按<MODE>闪光模式选择 按钮 屏幕显示<MULTI> 转动调节旋钮设置闪光输出 功率 按功能按钮< 按<MODE>模式选择按钮 MULTI >选 择闪光次数 旋转调节旋 屏幕显示<M> 钮设定数字 按功能按钮< Hz >选 择闪光频率 旋转调节旋 钮设定数字 转动调节旋钮设置闪光输出 按下<SET>设置按钮 确定 所有设置都将显示出来 计算快门速度 拍摄过程中更改闪光输出时 下表将清楚地显示光圈值是如何更改 的 如/-0. /+0. 您可以在增加或减少闪光输出时查看光圈 值的更改规律 例如 将闪光输出量减少至/ /-0.或/-0.7 然后再将其增 加至大于/ /+0. /+0.7时 将显示/ /-0.7 / /-0. /+0. / /+0.7 的公式计算快门速度 然后用相机进行设置 闪光次数/闪光频率 快门速度 例如 如果闪光次数是0 闪光频率是5Hz 快门速度则至少为秒 闪光连拍 闪光0次后 请让闪光灯至少冷却5分钟 如果 /-0.7 / 在频闪闪光过程中 到闪光停止为止快门应保持开启状态 使用下面 为防止闪光灯头过热并损坏 请勿执行连续0次以上的频闪 减少闪光输出指数 /+0.7 设置闪光频率和闪光次数 按下<SET>设置按钮确定 闪光曝光补偿 显示闪光输出 / 0. 功率 /+0. 您试图执行连续0次以上的频闪闪光连拍 为防止闪光灯头 过热 闪光可能自动停止 如果发生了这种情况 请让闪光 灯至少冷却5分钟 增加闪光输出指数 反光很强的被摄体在暗背景前使用频闪闪光更加有效 S光控单元设置 推荐使用三脚架和遥控开关 在M手动闪光模式下 按<S/S>可以使用S功能 闪光灯可作为 闪光输出为/和/时不能设置频闪闪光 副灯使用 创造多种照明效果 适用于手动闪光环境 它会与主闪光 频闪闪光时也可以使用 bulb 灯的第一次闪光同步触发闪光 效果与使用无线引闪器一致 如果闪光次数显示为-- 则闪光灯会连续闪光 直到快门或 电池耗尽 如下表所示 闪光次数将受到限制 S光控单元设置 在M手动闪光模式下 按<S/S>可以使用S功能 闪光灯可作为 最大频闪闪光次数 副灯使用 适用于TTL闪光环境 具有防预闪功能 使用带一次预闪 闪 Hz 光输出 功能的相机能用光控实现同步拍摄 它会与主闪光灯的第二次闪光同 / 7 6 /8 /6 0 0 / /6 /8 步触发闪光 即次光控引闪 手动离机高速设置 在M手动闪光模式下, 按 SYNC 选择高速模式 显示 此时引闪 会进行高速闪光 只有在M模式下才支持S/S光控引闪模式和离机高速模式

8 从属单元设置 无线闪光拍摄 光学传输 按下< >无线设置按钮 令屏幕显 该产品支持SONY无线闪光系统(WL) 具备无线闪光功能 具有主控 示< >和< 闪光和从属闪光功能 作为主控单元 可以控制并引闪HVL-F60M 示橙色 > 此时背光显 HVL-FM HVL-FM等SONY闪光灯 作为从属单元 受控 HVL-F60M HVL-FM HVL-FM闪光灯无线信号 从而实现 无线闪光 退出光无线模式 由于原厂闪光灯无线协议限制 需注意以下几点: 在Master状态只有TTL闪光和OFF状态 M闪光模式设置只可在 闪光模式 强制闪光 Slave模式下设置 光无线系统(WL)没有Multi闪光模式 SLOW 当从属单元设置为M模式时 请把主控单元该组别设置为TTL REAR WL 主控单元/从属单元设置位置和范围 需要设置相机的闪光模式为 非无线闪光模式 按下< >无线设置按钮 切 换其他模式 5米(9.英尺) 室内 设置主控闪光灯的闪光模式 在禁用主控单元闪光模式下 只有从属单元的闪光灯闪光 室外 按功能按钮< Gr >选择M/A/B组 0米(.8英尺) 别 再按功能按钮<MODE>选择 80 主控单元的闪光模式可以在OFF / TTL 之间进行切换 选择其中一种 8米(6.英尺) 作为主控单元的闪光模式 米(9.英尺) 即使有多个从属单元 主控单元也可通过无线控制所有的闪 光灯 本说明手册中 主控单元 指安装在相机上的闪光灯 从属单元 指通过无线控制的闪光灯 设置通讯频道 如果在拍摄现场不止一个无线闪光系统 您可以通过更改通讯频道来 防止信号干扰 保证主控单元和从属单元设置为相同的频道编号即 可 无线设置 您可以在普通闪光和无线闪光之间切换 对于普通闪光 请务必将无 按下功能按钮< CH > 旋转调节旋钮从至中选择 频道 线设置设为 关 主控单元设置 按下< >无线设置按钮 令 此时背光显示绿色 屏幕显示< CTRL+> 按下<SET>设置按钮确定 闪光模式 无线遥控 注 光无线系统(WL)由于受原 协议限制 考虑到和原厂 SLOW 兼容 无法进行优化和改进 所以推荐使用无线电(.G)传 REAR 输闪光模式 具备操作更加简单 闪光创意更加随意 抗干 扰强等优点 WL 注: 机顶灯连接相机 在主控单元模式< CTRL+>下 需要 设置相机的闪光模式为无线闪光模式< WL> 如果相机不在 <WL>状态 机顶灯会提示 SET YOUR CAMERA 如 何设置相机无线系统闪光模式<WL> 请查看相机说明书

9 无线闪光拍摄 无线电(.G)传输 按" "按钮可切换至 Multi模式 无线电创意系统 支持创建三个从属单元组 并实现TTL自动闪 光 您可以通过TTL自动闪光轻松获取多种照明效果 使用主控单元按组分别设置的任何TTL自动闪光 手动闪光和频闪 闪光设置都会被自动传输到从属单元 因此 在拍摄时无需操作从 属单元 只需在主控单元上对每个从属组进行单独设置就可完成 将此产品设置为主控单元时 可以在TTL/M/Multi/OFF四种 设置通讯频道 如果在拍摄现场不止一个无线闪光系统 您可以通过更改通讯频道来 闪光模式下工作 防止信号干扰 保证主控单元和从属单元设置为相同的频道编号即 可 即使有多个从属单元 主控单元也可通过无线控制控制所有 的闪光灯 本说明手册中 主控单元 指安装在相机上的闪光灯 从属单元 指通过无线控制的闪光灯 按下功能按钮< CH > 旋转调节旋钮从至中选择 频道 无线设置 您可以在普通闪光和无线闪光之间切换 对于普通闪光 请务必将无 线设置设为 关 按下<SET>设置按钮确定 主控单元设置 按下< >无线设置按钮 令 屏幕显示< < > 如显示 MULTI> 表示频闪模 式 TTL: 全自动无线闪光拍摄 使用一个从属单元闪光 此时背光显示绿色 从属单元设置 设置主控单元 将安装在相机上的 V860IIS设为主控单元 按下< >无线设置按钮 令 此时背光显示橙色 屏幕显示< >和< (第5页) M/A/B/C都可独立设置为 > TTL 将要被无线控制的 V860IIS设为从属单元 (第5页) 设置主控闪光灯的闪光模式 设置从属单元 按功能按钮< Gr >选择 M/A/B/C组别 再按功能按 钮 <MODE> 选择主控单 元的闪光模式可以在OFF / TTL / M 之间进行切换 选 择其中一种作为主控单元的 闪光模式 可以选择A/B/C 5 检查传输频道 将主控单元和从属单元的 频道设为一致 (第6页) 定位相机和闪光灯 将其定位在(第页)所示 的范围内 检查闪光灯是否准备就绪 检查主控闪光灯就绪指示 灯点亮 当从属闪光灯就绪时 自 动对焦辅助光发光区域以 秒间隔闪烁

10 6 检查操作 6 Multi:手动无线闪光拍摄 按下主控闪光灯的试闪按 设定<Multi>频闪模式 钮< > 按下<MODE>模式选择按钮 从属单元闪光 如果从属 令屏幕显示 < 单元不闪光 检查是否将其 MULTI> 设定频闪闪光设置 (第页) 放置在操作范围内 如果从属单元附近有荧光灯或电脑显示器 这些光源的存在 使具有无线电传输无线拍摄功能的闪光灯 主控/从属 可按照与 可能会导致从属单元发生故障 并导致其意外闪光 普通TTL自动闪光拍摄同样的方法 轻松利用高级无线多重闪光照明 进行拍摄 如果从属单元的自动关闭电源生效 按主控单元的测试闪光 按钮打开从属单元 请注意在相机的测光定时工作期间 无 基本相对位置和操作范围如图所示 只要将主控单元设定为<TTL>就 可以进行无线自动闪光拍摄 法进行测试闪光 可以改变到从属单元的自动关闭电源生效为止的时间 定位和操作范围(无线闪光拍摄的示例) 使用一个从属单元进行自动闪光拍摄 第6页 C.Fn-Sv APOT/第页 可以进行设置以使自动对焦辅助发射器在从属单元回电完毕 时不闪烁 C.Fn-AF/第页 (主控) (从属) 使用全自动无线闪光 在主控单元上设定的闪光曝光补偿和其他设置也会在从属单元中自动 传输距离约00米 设定 不需要操作从属单元 可按照与普通闪光拍摄相同的方法使用 以下设置进行无线闪光拍摄 闪光曝光补偿( /第0页) 关于主控单元 使用附带的微型支架定位从属单元 可以使用两个或两个以上主控单元 通过准备多台装有主控单元的相 开始拍摄前请进行测试闪光和试拍 机 可以在保持相同照明 从属单元 期间更换相机进行拍摄 受从属单元的位置 周围环境 天气状况等影响 传输距离 可能更短 5 M:手动无线闪光拍摄 无线多重闪光拍摄 使用手动闪光的无线 多重闪光 拍摄 可以为每个从属单元 闪光 组 设定不同的闪光输出进行拍摄 在主控单元上设定所有参数 可以将从属单元分割为两个或三个组同时进行TTL自动闪光拍摄 此 外 可以为各闪光组 最多个组 设定并用不同的闪光模式拍摄 将闪光模式设为<M> 按下功能按钮 < Gr >选 用两个从属组进行自动闪光拍摄 择组别 再按功能按钮 <MODE> 设定为M模式 设置闪光输出 在选择组别状态下 按功 能按钮 < A >选择功率 设定 旋转调节旋钮为闪光 B 组设定闪光输出 并按 <SET>设置按钮确定 拍摄照片 各组以设定的闪光光比闪 光

11 用三个从属组进行自动闪光拍摄 同步插孔触发 同步插孔规格为 Φ.5mm, 此处可插入同步线或者触发器触发插头对 闪光灯进行同步引闪 A C B 自动辅助对焦灯在低亮度或低对比度的拍摄情况下, 闪光灯内置的自动对焦辅助灯将开启, 使自动对焦更容易 当对焦困难时, 红色辅助对焦灯亮起 ; 当对焦准确, 辅助对焦灯自动熄灭 如想关闭自动辅助对焦功能, 在 C.Fn 设置 AF 至 OFF 用户在使用时, 如发现辅助对焦灯未亮起, 是因为相机已经处于准确对焦状态 无线电传输比光学传输的拍摄具有优势, 距离更远, 耗电更少, 受障 碍物的影响更小 无线电传输和光学传输的差异 : 功能传输距离频道受干扰程度 无线电传输 00m ~ 难 光学传输 5m ~ 易 位置有效范围中央 0.6~0 米 /.0~.8 英尺边缘 0.6~5 米 /.0~6. 英尺反射闪光通过将闪光灯头指向墙壁或天花板, 闪光在照亮被摄体前被墙面反射 这可以减轻被摄物体背后的阴影, 获得更自然的摄影效果 称之为反射闪光 其他应用外置无线控制功能 闪光灯内置无线控制插座, 配合特定遥控器使用, 您可以实现对闪光灯的无线控制 将 FT 系列遥控器的接收端插入无线控制插座, 手持遥控器发射端, 即可远程控制闪光灯的功率开关和大小 闪光灯触发等 您也可以将发射端置于相机热靴上, 通过相机快门来进行同步引闪 旋转闪光灯头来设置反射方向 更多遥控器的使用方法, 请查阅 FT 系列遥控器的说明书 如果墙壁或天花板太远, 反射闪光可能太弱并导致曝光不足 墙壁或天花板应该是平坦的 白色的以利于高效的反射 如果反射表面不是白色的, 照片将出现偏色

12 创建眼神光 C.Fn 设置自定义功能 使用眼神光板 您可以在被摄体的眼睛中创建眼神光以使面部表情更 加生动 请对照以下图表本机应用栏 使用自定义功能来完成设置 将闪光灯头向上旋转 自定义 设置符号 设置和说明 距离指示显示 m 米 ft 英寸 ON 启动 OFF 关闭 ON 启动 OFF 关闭 从属单元自动 60min 60分钟 关闭电源计时器 0min 0分钟 蜂鸣器 ON 启动 OFF 关闭 sec 秒后自动熄灭 OFF 一直熄灭 ON 一直点亮 0~9 0个级别 拉出广角散光板 同时弹出 m/ft 眼神光板 APO 功能 功能符号 自动关闭电源 推入广角散光板 仅推入广角散光板 按照反射闪光中相同的步 AF 自动对焦辅助光闪光 骤进行 Sv APOT BEEP 请将闪光灯头向前指然后向上旋转度 如果左右旋转闪 光灯头就不会产生眼神光 要获得最好的眼神光效果 被摄体不能处于相机.5米 LIGHT 背光点亮时间 /.9英尺以内 ZOOM 设置闪光覆盖范围并使用广角散光板 LCD 液晶屏对比度 该闪光灯有两种变焦方式 自动变焦和手动变焦 可以设置闪光覆盖 范围以匹配0-00毫米的镜头焦距 自动变焦时 焦距会随相机变 焦镜头的改变而变化 以提供最佳闪光效果 同样 使用内置的广角. 长按< Zm/C.Fn >背光/自定义按钮秒或更长 直到显示C.Fn菜 单 右上角 Ver x.x 表示软件版本号. 选择自定义功能符号 散光板 闪光覆盖范围可以扩展为毫米广角镜头 旋转调节旋钮设置自定义功能符号 手动变焦时 按下<ZOOM/C.FN> 变焦/无线设置按钮 按 < SET > 设置按钮 自定义功能编号闪烁 转动调节旋钮更改闪光覆盖范围 在显示<. 更改设置 >状态下 将自动 旋转调节旋钮设置想要的编号 按 < SET > 按钮确定 设置自定义功能后按下功能按钮< 设置闪光覆盖范围 >模式选择按钮 相机 可以进行拍摄. 在C.Fn状态下 长按 Clear 按钮秒直至出现 OK 表示重 如果手动设置闪光覆盖范围 确保其覆盖镜头焦距 这样照 置C.Fn的参数 片就不会出现阴影边缘 使用广角散光板 拉出广角散光板并将其置于闪光灯 头上 闪光覆盖范围将扩展至毫 米 同时弹出眼神光板 请推回眼神 光板 <ZOOM/C.FN>按钮不起作用 电池电量低时 电池符号< > 会闪烁 此时请更换电池

13 保护功能. 热保护 为防止闪光灯头过热并损坏, 请勿在 / 功率时进行超过 0 次的快速连续闪光 0 次连续闪光后, 要让闪光灯至少冷却 0 分钟 如您在进行超过 0 次连续闪光后马上继续进行更多次闪光, 内部的防过热功能可能会被激活, 使充电时间变为 0 秒以上 如果发生这种现象, 请让闪光灯冷却约 0 分钟, 闪光灯便会恢复正常 热保护启动后, 显示屏上的符号会显示 激活热保护功能的连续闪光次数 : 功率次数 / 0 / / / 60 /(+0.,+0.7) 00 /8(+0.,+0.7) 00 /6(+0.,+0.7) 00 /(+0.,+0.7) 500 /6(+0.,+0.7) 000 /8(+0.,+0.7) 高速同步模式下, 激活热保护功能的连续闪光次数 : 功率次数 / 5 /(+0.,+0.7); 0 /(+0.,+0.7) 0 /8(+0.,+0.7); /6(+0.,+0.7) 0 /(+0.,+0.7); /6(+0.,+0.7); 50 /8(+0.,+0.7); 规格参数 型号 V860IIS 类型 兼容相机闪光指数 (/ 档位 ;00mm 焦距 ) 闪光覆盖范围 SONY 索尼数码单镜反光照相机 60(m ISO 00) (feet ISO 00) 0 00 毫米 自动变焦 ( 自动设置适合镜头焦距和图像尺寸的闪 光覆盖范围 ) 手动变焦 闪光灯头旋转 / 倾斜, 水平 0~60, 垂直 -7 ~ ( 反射闪光 ) 闪光持续时间 /00 秒 -/0000 秒 曝光控制 曝光控制系统闪光曝光补偿 (FEC) TTL 自动闪光 手动闪光手动, 闪光包围曝光 : 在 ± 档间以 / 档为增量调节 ( 可以组合使用手动闪光曝光补偿 ) 同步方式频闪闪光 高速同步 ( 最高 /8000 秒 ), 前帘同步, 后帘同步具备 ( 次数 : 次 ;00Hz) 无线闪光 ( 光学传输和无线电.G 传输 ) 无线功能可控制从属单元组 光学.G 主控单元, 从属单元, 关闭 组 :A, B 组 :A, B,C 传输范围 ( 约 ) 光学 室内 :< 米 /9. 英尺室外 :<8 米 /6. 英尺 接收角度 : 水平 ±0, 垂直 ±0.G 00m 频道 光学 组 :,,,.G 组 :~ 从属单元准备就绪指示灯 两红灯同时亮起. 其他保护 为了保证设备安全的工作, 系统时刻进行预防保护, 以下提示符号 供您参考 : LCD 显示 E E E E9 警示内容 闪光灯回电系统出现问题, 无法回电引闪, 请重新开机, 如无法解决请维修 设备内温度过高, 请停止引闪 0 分钟 闪光灯管两端电压过高, 请维修 固件升级有误, 请进行正确固件升级 自动对焦辅助光有效范围 ( 约 ) 电源内装锂电回电时间全功率闪光次数节能 同步触发方式 色温 尺寸体积净重 ( 不含电池 ) 中央 :0.6-0 米 / 边缘 :0.6-5 米.V/000mAh 锂聚合物电池 <.5 秒, 闪光灯准备就绪,LED 红色指示灯亮起约 650 次闪光灯在无人操作 秒左右将会自动关闭电源 设置为从属单元时 60 分钟进入休眠状态 热靴,.5mm 同步线, 无线控制插座 5600±00k 6*76* mm 0g

14 故障排除指南 固件升级 如果遇到问题, 请参阅此故障排除指南 闪光灯不充电 电池安装方向错误 以正确的方向安装电池 闪光灯的内置电池耗尽 如果闪光灯 LCD 屏幕上 < > 显示并闪烁, 表明需要更换电池 本机通过 USB 插座可进行固件升级 软件最新公告及说明将会发布在官方网站上 注 : 本品出厂不配 USB 升级线, 请另行购买 普通的 USB 线可使用, 本产品 USB 口为 Micro USB 接口 闪光灯不闪光 闪光灯没有牢固地安装在相机上 将闪光灯的固定座牢固地安装在相机上 闪光灯和相机的电子触点变脏 请清洁触点 电源自动关闭 当灯作为主控单元时, 秒无操作后, 自动电源关闭功能生效 半按快门按钮或机身任意按键唤醒 作为从属单元在 60 分钟 ( 或者选择 0 分钟 ) 无任何操作时, 闪光灯会进入休眠状态 可按机身任意按键唤醒 自动变焦不工作 闪光灯没有牢固地安装在相机上 将闪光灯的固定座牢固地安装在相机上 兼容相机列表 本机可兼容以下 SONY 数码单镜反光照相机型号 : α77ii α7rii α7r α58 α99 注 :. 此表格仅列举目前已测试的相机型号, 未涵盖所有 SONY 数码单镜反光照相机 其他相机型号, 用户可自行测试. 本公司保留未来修改此表格内容的权利 ILCE6000L 闪光曝光不足或过度 使用高速同步 使用高速同步, 有效的闪光范围会更小 确保被摄体位于显示的有效闪光范围内 闪光灯使用手动曝光模式 改为 TTL 模式或修改闪光输出功率设置 相片出现暗角或者被摄物体只有局部能照亮 相机镜头焦距超出闪光灯的覆盖范围 请检查闪光灯当前的覆盖焦距 本产品的灯头变焦范围是中画幅系统的 0-00mm, 您可以尝试拉出广角闪光板, 以扩大闪光范围 维护保养 闪光灯在工作时, 如发现异常, 应立即关掉电源, 查明原因 灯体应避免震动, 平时注意表面除尘 灯体稍有发热为正常现象, 无特别需要时, 勿连续引闪 闪光灯的所有维修概由本厂指定可供原厂配件之维修部负责 年保修, 消耗品如灯管等, 不在 年保修范围 经发现, 擅自检修此闪光灯的, 将取消闪光灯之一年保修期, 维修需要收取相关费用 如果本品出现故障或者被水淋湿, 在专业人员维修后方可继续使用 如有技术更改, 恕不另行通知

15 Foreword For Your Safety Thank you for purchasing this product. This V860IIS camera flash applies to Sony DSLR series cameras and is compatible with TTL autoflash. With this TTL compatible flash, your shooting will become simpler. You can easily achieve a correct flash exposure even in complex light-changing environments. This camera flash features: GN60 (m ISO steps from / to /8. Pro 000mAh Li-ion Battery.5s recycle 650 full power pops. Fully support Sony TTL camera flash. Workable as Master or Slave unit in a wireless flash group. Use dot-matrix LCD panel to make clear and convenient operations. With built-in.ghz wireless remote system to support transmitting and receiving. Provided multiple functions, include HSS (up to /8000s), FEC, etc. Use optional FT-6S to adjust flash parameters & trigger the flash. Stable consistency and color temperature with good even lighting. Support with firmware upgrade. Always keep this product dry. Do not use in rain or in damp conditions. This product contains high-voltage electronic parts. Touching the high-voltage circuit inside it may result in electric shock. Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center. Stop using this product if it breaks open due to extrusion, falling or strong hit. Otherwise, electric shock may occur if you touch the electronic parts inside it. Do not fire the flash directly into the eyes (especially those of babies) within short distances. Otherwise visual impairment may occur. When taking pictures for babies, keep the flash unit at least meter (. feet) away from them. Using bounce flash to reduce light intensity is also recommended. Do not use the flash unit in the presence of flammable gases, chemicals and other similar materials. In certain circumstances, these materials may be sensitive to the strong light emitting from this flash unit and fire or electromagnetic interference may result. Do not leave or store the flash unit in places where the ambient temperature reads over 50 C (e.g. in automobile). Otherwise the electronic parts may be damaged

16 Pioneering Li-ion Camera Flash Conventions used in this Manual This manual is based on the assumption that both the camera and camera flash s power switches are powered on. Reference page numbers are indicated by p.**. The following alert symbols are used in this manual: The Caution symbol gives supplemental information. The Note symbol indicates a warning to prevent shooting problem Contents Foreword For Your Safety Name of Parts Body Control Panel LCD Panel What's in the Box of V860IIS Kit? What's in the Box of V860IIS (only flash unit)? Separately Sold Accessories Battery Attaching to a Camera Power Management Flash Mode: TTL Autoflash FEC (Flash Exposure Compensation) High-Speed Sync Second-Curtain Sync M: Manual Flash Multi: Stroboscopic Flash Wireless Flash Shooting: Optical Transmission Wireless Settings Setting Master Unit s Flash Mode Setting the Communication Channel Wireless Flash Shooting: Radio (.G) Transmission Wireless Settings Setting Master Unit s Flash Mode Setting the Communication Channel TTL: Fully Automatic Wireless Flash Shooting M: Wireless Flash Shooting with Manual Flash Multi: Wireless Flash Shooting with Manual Flash Other Applications Wireless Control Function Sync Triggering Auto Focus Assist Beam Bounce Flash Creating a Catchlight ZOOM: Setting the Flash Coverage and Using the Wide Panel Low Battery Warning C.Fn: Setting Custom Functions Protection Function Technical Data Troubleshooting Firmware Upgrade Compatible Camera Models Maintenance

17 LCD Panel Name of Parts () TTL Autoflash Zoom : zoom display (Page 8) Focus length (Page 8) : High-speed sync : Automatic (Page 7) : Manual(Page 7) TTL : TTL autoflash Distance indicator display 0 : Flash exposure compensation (Page 6) Flash exposure compensation amount The display will only show the settings currently applied. The functions displayed above function buttons to, such 08 as Body SYNC and, change according to settings status. When a button or dial is operated, the LCD panel 0. Catchlight Panel 08. Hotshoe 0. Built-in Wide Panel 09. Dot-marix LCD Panel 0. Flash Head 0. Lock Ring 0. Optic Control Sensor. Battery Compartment illuminated. 05. Focus Assist Beam. USB Port 06. Sync Cord Jack. Slave Flash Ready Indicator ()M Manual Flash M : Manual flash 07. Wireless Control Port Manual flash output RST SET 9 Control Panel. <MODE> Mode Selection Button / Lock button 5. < >Wireless Selection ()Multi Flash Multi : Stroboscopic flash Number of flashes Flash frequency 9. < > Test Button / Flash Ready Indicator 0. Function Button Button. Function Button 6. Select Dial. Function Button 7. <SET> Set Button. Function Button 8. ON/OFF Power Switch

18 () Optical Transmission Shooting Separately Sold Accessories Master Unit The product can be used in combination with the following accessories sold separately, so as to achieve best photography effects: : Radio transmission Flash mode XT-S wireless flash trigger, FT-6S power & trigger control, Mini Gr : Group flash (radio transmission) wireless shooting softbox, White & Silver reflector, Honeycomb, Color gels, Snoot, etc. : Optic transmission wireless shooting FEC Firing group Channel Slave Unit Battery : Slave : Slave icon Features. This flash unit uses Li-ion polymer battery which has long runtime. The available charge-and-discharge times are It is reliably safe. The inner circuit is against overcharge, overdischarge, overcurrent, and short circuit.. Take only.5 hours to fully charge the battery by using the standard battery charger. What s in the Box of V860IIS Kit?. Flash Unit. Li-ion Battery Pack. Battery Charger Cable 6. Protection Case. Battery Charger Cautions 5. Mini Stand 7. Instruction Manual What s in the Box of V860IIS (only flash unit)?. Flash Unit 5. Mini Stand 6. Protection Case 7. Instruction Manual. Do not short circuit.. Do not expose to rain or immerse into water. This battery is not water proof.. Keep out of reach of children.. No over hours continuous charging. 5. Store in dry, cool, ventilated places. 6. Do not put aside or into fire. 7. Dead batteries should be disposed according to local regulations. 8. If the battery had ceased using for over months, please make a full recharge. Loading and Unloading the Battery To load the battery, push the battery compartment cover downward and open it. According to the triangle sign on the battery pack, insert it into the compartment until a white knob locks the battery with a click sound. - -

19 To unload the battery, tap the white knob and the battery pack will pop out. Then close the compartment. C.Fn Disabling Auto Power Off function is recommended when the flash is used off camera. (C.Fn-APO, Page 9) C.Fn Slave Auto Power Off Timer is set to 60 minutes by default. Another option 0 minutes is available. (C.FnSv APOT, Page 9) Battery Level Indication Make sure the battery pack is securely loaded in the flash. Check the battery level indication on the LCD panel to see the remaining battery level. Battery Level Indication Meaning grids Full grids Middle grid Low Blank grid Lower battery, please recharge it. Blinking The battery level is going to be used out immediately. And the flash will auto power off in minute. Note: Please recharge the battery as soon as possible (within 0 days). Then, the battery can be used or be placed for long period. Flash Mode: TTL Autoflash This flash has three flash modes: TTL, Manual (M), and Multi (Stroboscopic). In TTL mode, the camera and the flash will work together to calculate the correct exposure for the subject and the background. In this mode, multiple TTL functions are available: FEC, HSS, second curtain sync, modeling flash, etc. * Press <MODE> Mode Selection Button and three flash modes will display on the LCD panel one by one with each pressing. TTL Mode Press <MODE> Mode Selection Button to enter TTL mode. The LCD panel will display <TTL>. Attaching to a Camera Press the camera release button halfway to focus. The aperture and effective flash range will be displayed in the viewfinder. Attach the Camera Flash. Slip the camera flash s mounting foot into the camera s hotshoe all the way. When the shutter button is fully pressed, the flash will fire a preflash that the camera will use to calculate exposure and flash output the instant before the photo is taken. FEC: Flash Exposure Compensation Secure the Camera Flash. Rotate the lock ring on the mounting foot until it locks up. With FEC function, this flash can adjust from - to + in /rd stops. It is useful in situations where minor adjusting of the TTL system is needed based on the environment. Setting FEC: Press Function Button < >. The icon < > and flash exposure compensation amount will be highlighted on the LCD panel. Set the flash exposure compensation amount. Detach the Camera Flash. Rotate the lock ring on the mounting foot until it is loosened. Turn the Select Dial to set the amount. 0. means / step, 0.7 means / step. Power Management Use ON/OFF Power Switch to power the flash unit on or off. Turn off if it will not be used for an extended period of time. Setting as a master flash, it will turn the power off automatically after a certain period (approx. seconds) of idle use. Pressing the camera shutter halfway or pressing any flash button will wake up the flash unit. Setting as a slave flash, it will enter sleep mode after a certain period (adjustable, 60 minutes by default) of idle use. Pressing any flash button will wake it up To cancel the flash exposure compensation, set the amount to +0. Press < SET > button again to confirm the setting

20 High-Speed Sync Optical S Secondary Unit Setting High Speed Sync (FP flash) enables the flash to synchronize with all camera shutter speeds. This is convenient when you want to use aperture priority for fill-flash portraits. As high-speed sync setting is determined by Sony camera s shutter, please refer to your camera s manual. In M manual flash mode, press <S/S> button so that this flash can function as an optic S secondary flash with optic sensor. With this function, the flash will fire synchronously when the main flash fires, the same effect as that by the use of radio triggers. This helps create multiple lighting effects. Optical S Secondary Unit Setting With high-speed sync, the faster the shutter speed, the shorter the effective flash range. Multi flash mode cannot be set in high-speed sync mode. Over-temperature protection may be activated after 5 consecutive high-speed sync flashes. Press <S/S> button so that this flash can also function as an optic S secondary flash with optic sensor in M manual flash mode. This is useful when cameras have pre-flash function. With this function, the flash will ignore a single preflash from the main flash and will only fire in response to the second, actual flash from the main unit. Manual Off Camera High-speed Setting In M manual flash mode, press < SYNC > button to select high-speed mode and is displayed. Second-Curtain Sync With a slow shutter speed, you can create a light train following the subject. The flash fires right before the shutter closes. Set Sony camera to Rear mode. S and S optical triggering is only available in M manual flash mode. M: Manual Flash Multi: Stroboscopic Flash The flash output is adjustable from / full power to /8th power in /rd stop increments. To obtain a correct flash exposure, use a hand-held flash meter to determine the required flash output. Press < MODE > button so that < M > is displayed. With stroboscopic flash, a rapid series of flashes is fired. It can be used to capture a multiple images of a moving subject in a single photograph. You can set the firing frequency (number of flashes per sec. expressed as Hz), the number of flashes, and the flash output. Press <MODE> button so that < MULTI > is displayed. Set the flash frequency and flash times. Turn the Select Dial to choose a desired flash output. Press Function Button Turn the Select Dial to choose a desired flash output amount. Press < SET > button again to confirm the setting. Flash Output Range The following table makes it easier to see how the stop changes in terms of f/stop when you increase or decrease the flash output. For example, when you decrease the flash output to /, /-0., or /0.7, and then increase the flash output to more than /, /+0., /+0.7, and / will be displayed. Figures displayed when reducing flash output level /-0. /-0.7 / /-0. /+0.7 /+0. /-0.7 / / /+0.7 /+0. < MULTI > to select the flash times. Turn the Select Dial to set the number. Press Function Button < Hz > to select the flash frequency. Turn the Select Dial to set the number. After you finish the setting, press <SET> button and all the settings will be displayed. Calculating the Shutter Speed During stroboscopic flash, the shutter remains open until the firing stops. Use the formula below to calculate the shutter speed and set it with the camera. Number of Flashes / Flash Frequency = Shutter Speed For example, if the number of flashes is 0 and the firing frequency is 5 Hz, the shutter speed should be at least seconds. Figures displayed when increasing flash output level

21 Maximum Stroboscopic Flashes: Flash output To avoid overheating and deteriorating the flash head, do not use stroboscopic flash more than 0 times in succession. After 0 times, allow the camera flash to rest for at least 5 minutes. If you try to use the stroboscopic flash more than 0 times in succession, the firing might stop automatically to protect the flash head. If this happens, allow at least 5 minutes rest for the camera flash. Stroboscopic flash is most effective with a highly reflective subject against a dark background. Using a tripod and a remote control is recommended. A flash output of / and / cannot be set for stroboscopic / /8 /6 / /6 /8 flash. Stroboscopic flash can be used with bulb. If the number of flashes is displayed as --, the firing will continue until the shutter closes or the battery is exhausted. The number of flashes will be limited as shown by the following table. Hz Slave/Master Unit s Positioning and Operation Range Outdoors Indoors 80 8m(6.ft) 0m(.8ft) 5m(9.ft) m(9.ft) Even with multiple slave units, the master unit can control all of them via wireless. In this user manual, master unit refers to the camera flash on a camera and slave unit will be controlled by the master unit.. Wireless Settings You can switch between normal flash and wireless flash. For normal flash shooting, be sure to set the wireless setting to OFF. Flash Mode Wireless Master Unit Setting Press < > button so that < CTRL+> is displayed on the LCD panel. The backlight turns green now. Wireless Flash Shooting: Optical Transmission This product is compatible with Sony Wireless Lighting System (WL). It can function as either an optical wireless master or slave flash. As a master unit, it can control Sony camera flashes e.g. HVL-F60M, HVL-FM and HVL-FM via wireless. As a slave unit, it can be controlled by wireless signals of Sony camera flashes e.g. HVL-F60M, HVL-FM and HVL-FM. For the restrictions of Sony camera flash s wireless protocol, there are several points to be noticed: Master unit only has TTL and OFF mode. And M flash mode can only be set under the slave mode. Optical wireless lighting system (WL) do not have Multi mode. When setting the slave unit to M mode, please set the group of the master unit to TTL mode. SLOW REAR WL Note: In the master unit mode < CTRL+>, you should set the camera to wireless lighting mode (WL) when attaching the camera flash to the camera. If the camera are not set to WL state, a note SET YOUR CAMERA will be displayed on the camera flash. As for how to set camera to wireless lighting mode (WL), please refer to the camera s manual. Slave Unit Setting Press < > button so that < > and < > are displayed on the LCD panel. The backlight turns orange now

22 Exit Optical Wireless Lighting Mode Flash Mode Fill -flash SLOW REAR WL Set the camera to NON wireless lighting mode. Press < > Wireless Selection Button to switch to other modes.. Setting Master Unit's Flash Mode Press Function Button < Gr > to choose the group from M/A/B/C. Then, press Function Button < MODE > so that the master unit can work in OFF / TTL flash mode. Choose one of them as the flash mode of master unit.. Even with multiple slave units, the master unit can control all of them via wireless. In this user manual, master unit refers to the camera flash on a camera and slave unit will be controlled by the master unit.. Wireless Settings You can switch between normal flash and wireless flash. For normal flash shooting, be sure to set the wireless setting to OFF. Master Unit Setting Press < > button so that < > is displayed on the LCD panel. If < MULTI> is displayed, it means Multi mode is ON. The backlight turns green now. Slave Unit Setting. Setting the Communication Channel If there are other wireless flash systems nearby, you can change the channel IDs to prevent signal interference. The channel IDs of the master unit and the slave unit(s) must be set to the same. Press Function Button < CH > and turn the Select Dial to choose a channel ID from to. Press the <SET> button to confirm. Press < < > button so that > and < > are displayed on the LCD panel. The backlight turns orange now.. Setting Master Unit s Flash Mode Press Function Button Gr < > to choose the group from M/A/B/C. Then, press Function Button <MODE> so that the master unit can work in OFF/TTL/M flash mode. Choose one of them as the flash mode of master unit. Press < > button to switch to Multi mode. Note: As optical lighting system (WL) is restrained to Sony s wireless protocol, there is no much room for TT685S to improve its optical transmission mode. Therefore, radio transmission (.G) is recommended for its easier operation, creative lighting effects, stable signals, etc. Wireless Flash Shooting: Radio (.G) Transmission You can set up three slave groups for TTL autoflash shooting. With TTL autoflash, you can easily create various lighting effects. Any flash settings for the slave units on the master flash in TTL mode will be automatically sent to the slave units. So the only thing you need to do is to set the master unit for each slave group without any operation for the slave units at all during the shooting. This flash can work in TTL /M /Multi / OFF flash modes when set as a master unit Setting the Communication Channel If there are other wireless flash systems nearby, you can change the channel IDs to prevent signal interference. The channel IDs of the master unit and the slave unit(s) must be set to the same. Press Function Button < CH > and turn the Select Dial to choose a channel ID from to. - -

23 Press the <SET> button to confirm. If the slave unit s auto power off function is workable, press the master unit s test button to power it on. Please note that test firing is unavailable during the camera s regular metering time. The effective time of slave auto power off is changeable. (C.Fn-Sv APOT/ Page 9). TTL: Fully Automatic Wireless Flash Shooting Autoflash Shooting with One Slave Unit Master Unit Setting not blink after the slave unit s flash ready indicator is lightened. (C.Fn-AF/ Page 9) Attach a V860IIS camera Using Fully Automatic Wireless Flash flash on the camera and set it as the master unit. (Page ) M/A/B/C can be set as TTL mode independently. The FEC and other settings that set on the master unit will also be appeared on the slave unit automatically. The slave unit does not need any operation. Use the following settings to make wireless flashes according to the same methods with normal flash shooting. Slave Unit Setting Flash Exposure Compensation Set the V860IIS that to be Use two or more master units. By preparing several cameras that with master units flash attached, cameras can be changed in shooting while keeping the same lighting source (slave unit). Check the communication channel 5. M: Wireless Flash Shooting with Manual Flash slave unit(s) are set to a different channel, set them to the same channel. (Page ) Position the camera and flashes This describes wireless (multiple shooting) using manual flash. You can shoot with a different flash output setting for each slave unit (firing group). Set all parameters on the master unit. flashes as the picture shows. (Page 0) Check that the flash is ready Check that the master flash ready indicator is lightened. When the slave flash ready indicator is ready, the AF-assist beam lighting area will blinks at second intervals. 6 Check the flash operation Press the master unit s Test Button< Setting the flash mode to <M> Press Function Button < Gr > to choose groups. Then, press Function Button < MODE > to set the flash to M mode. Position the camera and 5 / Page 6 About Master Unit controlled as the wireless slave unit. (Page ) The slave unit can be set as A/B/C. If the master unit and By making some settings, the auto AF-assist transmitter will Setting flash output When choosing the group, press Function Button < > to select the power output. Turn the Select Dial to set the flash output of the groups. Press the <SET> button to confirm. Taking the picture Each group fires at the set flash ratio. >. Then, the slave unit will fire. If not, adjust the slave unit s angle toward the master unit and distance from the master unit. The slave unit might be out of order or fire an unwanted flash due to the nearby fluorescent lamp or computer screen Multi: Wireless Flash Shooting with Manual Flash Setting <Multi> stroboscopic flash. Press <MODE> button so that < MULTI> is displayed. Setting the stroboscopic flash. (Page 8) - -

24 Using a flash (master/slave) with a radio transmission wireless shooting function make it easy to shoot with advanced wireless multiple flash lighting, in the same way as TTL autoflash shooting. The basic relative position and operation range are as shown in the picture. You can then perform wireless TTL autoflash shooting just by setting the master unit to <TTL>. Function Distance Channel To be Disturbed Radio Transmission 00m ~ Hard Optical Transmission 5m ~ Easy Slave/Master Unit's Positioning and Operation Range Autoflash Shooting with One Slave Unit Other Applications Transmission distance is about 00m. Use the supplied mini stand to position the slave unit. Before shooting, perform a test flash and test shooting. The transmission distance might be shorter depending on the conditions such as positioning of slave units, the surrounding environment and whether conditions. Wireless Control Function The flash unit is built in with a Wireless Control Port so that you can wirelessly adjust the power level of the flash and the flash triggering. To control the flash wirelessly, you need a FT-6S remote control set (on-camera and on-flash). Insert its receive end into the Wireless Control Port on the flash and insert the transmit end into the camera hot shoe. Settings made on the hotshoe-mounted transmit and receive ends will be wirelessly communicated to the flash. Then you can press the camera shutter release button to trigger the flash. You can also hold the transmit end at hand to control your off-camera flash. Wireless Multiple Flash Shooting You can divide the slave units into two or three groups and perform TTL autoflash while changing the flash ratio (factor). In addition, you can set and shoot with a different flash mode for each firing group, for up to groups. For full instructions on the use of FT series remote control, see its user manual. A B A C B Sync Triggering The Sync Cord Jack is a Φ.5mm plug. Insert a trigger plug here and the flash will be fired synchronously with the camera shutter. Auto Focus Assist Beam In poorly-lit or low-contrast shooting environments, the built-in auto focus assist beam will automatically light on to make it easier for autofocus. The beam will light up only when autofocus is difficult and get out as soon as the autofocus becomes correct. If you want to turn off the auto focus assist beam, set the AF to OFF on the C.Fn settings. Auto Shooting with Two Slave Groups Auto Shooting with Three Slave Groups If you find the auto focus assist beam does not light up, this is because the camera has got a correct autofocus. Wireless shooting using radio transmission has advantages over wireless shooting using optical transmission, such as being less affected by obstacles, and not having to point the slave unit s wireless sensor toward the master unit. The main functional differences are as follows: Position Center Periphery Effective Range 0.6~0m /.0~.8 feet 0.6~5m /.0~6. feet

25 Bounce Flash By pointing the flash head toward a wall or ceiling, the flash will bounce off the surface before illuminating the subject. This can soften shadows behind the subject for a more natural-looking shot. This is called bounce flash. To set the bounce direction, hold the flash head and turn it to a satisfying angle ZOOM: Setting the Flash Coverage and Using the Wide Panel The flash coverage can be set automatically or manually. It can be set to match the lens focal length from 0 mm to 00mm. Also, with the built-in wide panel, the flash coverage can be expanded for mm wide-angle lenses. In Manual Zoom mode, press the <ZOOM/C.FN> button. Turn the Select Dial to change the flash coverage. If < > is displayed, the flash coverage will be set automatically. If you set the flash coverage manually, make sure it covers the lens focal length so that the picture will not have a dark periphery. Using the Wide Panel Pull out the wide panel and place it over the flash head as shown. The flash coverage will then be extended to mm. The catchlight panel will come out at the same time. Push the catchlight panel back in. If the wall or ceiling is too far away, the bounced flash might be too weak and result in underexposure. The wall or ceiling should be a plain, white color for high reflectance. If the bounce surface is not white, a color cast may appear in the picture. The <ZOOM/C.FN> button will not work. Low Battery Warning If the battery power is low, < > will appear and blink on the LCD panel. Please replace the battery Creating a Catchlight immediately. With the catchlight panel, you can create a catchlight in the subject s eyes to add life to the facial expression. Point the flash head upward by. Pull out the wide panel. The catchlight panel will come out at the same time. Push the wide panel back in. Push in only the wide panel. Follow the same procedures as for bounce flash. Point the flash head straight ahead and then upward by. The catchlight will not appear if you swing the flash head left or right. For best catchlight effect, stay.5m/.9ft away from the subject

26 C.Fn: Setting Custom Functions Protection Function The following table lists the available and unavailable custom functions of this flash. C.Fn Custom Functions Custom Function Signs m/ft APO AF Function Setting No. Settings & Description Distance indicator Auto power off AF-assist beam m ft ON OFF ON m feet ON OFF ON. Over-Temperature Protection To avoid overheating and deteriorating the flash head, do not fire more than 0 continuous flashes in fast succession at / full power. After 0 continuous flashes, allow a rest time of at least 0 minutes. If you fire more than 0 continuous flashes and then fire more flashes in short intervals, the inner over-temperature protection function may be activated and make the recycling time over 0 seconds. If this occurs, allow a rest time of about 0 minutes, and the flash unit will then return to normal. When the over-temperature protection is started, is shown on the LCD display. Sv APOT BEEP Slave auto power off timer Beeper OFF 60min 0min ON OFF OFF 60min 0min ON OFF Number of flashes that will activate over-temperature protection: Power Output Level Number of Flashes / 0 / / LIGHT Backlighting time sec Off in sec. / 60 OFF Always off /(+0.,+0.7) 00 ON Always lighting /8(+0.,+0.7) 00 LCD LCD contrast ratio 0~9 0 levels /6(+0.,+0.7) 00. Press <Zm/C.Fn> Backlight/Custom Setting Button for seconds or longer until C.Fn menu is displayed. The Ver x.x in the topright corner refers to the software version.. Select the Custom Function No. Turn the Select Dial to select the Custom Function No.. Change the Setting. Press<SET> button and the Setting No. blinks. Turn the Select Dial to set the desired number. Pressing <SET> button will confirm the settings. After you set the Custom Function and press Function Button < > to exit, then the camera will be ready to shoot.. In the C.Fn states, long press the Clear button for seconds until OK is displayed on the panel, which means the values in C.Fn can be reset. /(+0.,+0.7) /6(+0.,+0.7) /8(+0.,+0.7) Number of flashes that will activate over-temperature protection in high-speed sync triggering mode: Power Output / /(+0.,+0.7); /(+0.,+0.7) /8(+0.,+0.7); /6(+0.,+0.7) /(+0.,+0.7); Times /6(+0.,+0.7); /8(+0.,+0.7); 50. Other Protections The system provides real-time protection to secure the device and your safety. The following lists prompts for your reference: Prompts on LCD Panel Meaning E A failure occurs on the recycling system so that the flash cannot fire. E E E9 Please restart the flash unit. If the problem still exists, please send this product to a maintenance center. The system gets excessive heat. Please allow a rest time of 0 minutes. The voltage on two outlets of the flash tube is too high. Please send this product to a maintenance center. There are some errors occurred during the upgrading process. Please using the correct firmware upgrade method

27 Technical Data Troubleshooting Model V860IIS Type Compatible Cameras Sony DSLR cameras (TTL autoflash) Guide No. 60 (m ISO 00) (/ 00mm) (feet ISO 00) Flash Coverage 0 to 00mm Auto zoom (Flash coverage set automatically to match the lens focal length and image size) Manual zoom Swinging/tilting flash head (bounce flash): 0 to 60 horizontally and -7 to vertically Flash Duration /00 to /0000 seconds Exposure Control Exposure control system TTL autoflash and manual flash Flash exposure Manual. FEB: ± stops in / stop increments compensation (FEC) (Manual FEC can be combined.) Sync mode High-speed sync (up to /8000 seconds), first-curtain sync, and second-curtain sync Multi flash Provided (up to times, 00Hz) Wireless Flash (Optical transmission and.g transmission) Wireless flash function Master, Slave, Off Controllable slave groups Optical.G (A and B) (A, B and C) Transmission Optical Indoors: to 5 m / 9. to 9. ft. range Outdoors: 8 to 0 m / 6. to.8 ft. (approx.) Master unit reception angle: ±0 horizontally, ±0 vertically Channels.G Optical.G 00m (,,, and ) (~) Slave-ready indicator Two red indicators blink Auto Focus Assist Beam Effective range (approx.) Center: 0.6~0m /.0~.8 feet Periphery: 0.6~5m /.0~6. feet Power Supply Power source.v/000mah Li-ion polymer battery Recycle time <.5 seconds.red LED indicator will light up when the flash is ready. Full power flashes Approx. 650 Power saving Power off automatically after approx. seconds of idle operation. (60 minutes if set as slave) Sync Triggering Mode Hotshoe,.5mm sync line, Wireless control port Color Temperature 5600±00k Dimensions W*H*D 6*76* mm Weight without battery 0g If there is a problem, refer to this Troubleshooting Guide. The Camera Flash cannot be charged. The battery is installed in the wrong direction. Install the battery in the correct direction. The camera flash s internal battery is exhausted. If < > appears and blinks on the LCD panel, replace the battery immediately. The Camera Flash does not fire. The camera flash is not attached securely to the camera. Attach the camera s mounting foot securely to the camera. The electrical contacts of the Camera Flash and camera are dirty. Clean the contacts. The power turns off by itself. After seconds of idle operation, auto power off took effect if the flash is set as master. Press the shutter button halfway or press any flash button to wake up. After 60 minutes (or 0 minutes) of idle operation, the flash unit will enter sleep mode if it is set as slave. Press any flash button to wake up. Auto zoom does not work. The camera flash is not attached securely to the camera. Attach the camera flash s mounting foot to the camera. The flash exposure is underexposed or overexposed. You used high-speed sync. With high-speed sync, the effective flash range will be shorter. Make sure the subject is within the effective flash range displayed. You used Manual Flash mode. Set the flash mode to TTL or modify the flash output. Photos have dark corners or only parts of the target subject are illuminated. The focal length of lens exceeds the flash coverage. Check the flash coverage you set. This flash unit has the flash coverage between 0 and 00mm, which fits medium-format cameras. Pull the wide panel out to extend the flash coverage

28 Firmware Upgrade This flash supports firmware upgrade through the USB port. Update information will be released on our official website. USB connection line is not included in this product. The USB port is a standard Micro USB socket. Common USB connection line is applicable. Compatible Camera Models This flash unit can be used on the following Sony DSLR camera models: α77ii α7rii α7r α58 α99 ILCE6000L This table only lists the tested camera models, not all Sony DSLR cameras. For the compatibility of other camera models, a self-test is recommended. Rights to modify this table are retained. Maintenance Shut down the device immediately should abnormal operation be detected. Avoid sudden impacts and the product should be dedusted regularly. It is normal for the flash tube to be warm when in use. Avoid continuous flashes if unnecessary. Maintenance of the flash must be performed by our authorized maintenance department which can provide original accessories. This product, except consumables e.g. flash tube, is supported with a one-year warranty. Unauthorized service will void the warranty. If the product had failures or was wetted, do not use it until it is repaired by professionals. Changes made to the specifications or designs may not be reflected in this manual