KV-AR21M61

4-097-222-14 (2) Trinitron Color TV Operating Instructions Before operating the unit, please read this manual thoroughly and retain it for future reference. GB CT Panduan Pengendalian Sebelum mengendalikan unit, baca buku panduan ini dengan teliti dan simpan untuk rujukan masa depan. GB MY KV-AR21 KV-AR14 2003 Sony Corporation M61 M50

WARNING Dangerously high voltages are present inside the TV. TV operating voltage: 110 240 V AC (for Malaysia only: 220 240 V AC). Do not plug in the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground. To avoid battery leakage and damage to the remote, remove the batteries from the remote if you are not going to use it for several days. If any liquid leaks from the batteries and touches your skin, immediately wash it away with water. For your own safety, do not touch any part of the TV, the power cord and the antenna cable during lightning storms. For children s safety, do not leave children alone with the TV. Do not allow children to climb onto it. Do not place any objects on the TV. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. Do not operate the TV if any liquid or solid object falls into it. Have it checked immediately by qualified personnel only. Do not block the ventilation openings of the TV. Do not install the TV in a confined space, such as a bookcase or built-in cabinet. Clean the TV with a dry and soft cloth. Do not use benzine, thinner, or any other chemicals to clean the TV. Do not attach anything (e.g., adhesive tape, cellophane tape, glue) on the painted cabinet of the TV. Do not scratch the picture tube. 2 Do not open the cabinet and the rear cover of the TV as high voltages and other hazards are present inside the TV. Refer servicing and disposal of the TV to qualified personnel. Your TV is recommended for home use only. Do not use the TV in any vehicle or where it may be subject to excessive dust, heat, moisture or vibrations.

To prevent fire or shock hazard, do not expose the TV to rain or moisture. Do not plug in too many appliances to the same power socket. Do not damage the power cord. Install the TV on a stable TV stand and floor which can support the TV set weight. Ensure that the TV stand surface is flat and its area is larger than the bottom area of the TV. Pull the power cord out by the plug. Do not pull the power cord itself. Even if your TV is turned off, it is still connected to the AC power source (mains) as long as the power cord is plugged in. Unplug the TV before moving it or if you are not going to use it for several days. 3

x Securing the TV B KV-AR21M61 only To prevent the TV from falling, use the supplied screws, clamps and band to secure the TV. 20 mm 3.8 mm screws clamps band Screw the band to the TV stand and to the provided hole at the rear of your TV. or (1) Put a cord or chain through the clamps. (2) Screw one clamp to a wall or pillar and the other clamp to the provided hole at the rear of your TV. Note Use only the supplied screws. Use of other screws may damage the TV. 4

Table of Contents Installation Getting Started... 6 Setting up your TV ( Initial Setup )... 7 Additional Information Connecting optional components... 24 Troubleshooting... 26 Specifications... Back cover Overview of Controls TV top control, front and rear panels... 8 Using the remote control and basic functions... 9 Advanced Operations GB Selecting the picture and sound modes... 11 Enjoying stereo or bilingual programs (KV-AR21M61 only)... 12 Viewing Teletext (KV-AR21M61 only)... 13 Menu Adjustment Introducing the menu system... 14 Changing the Picture setting... 17 Changing the Sound setting... 18 Changing the Timer setting... 20 Changing the Channel Setup setting... 21 Changing the Setup setting... 23 5

Installation x Getting Started 1 Step 1 b Insert the batteries (supplied) into the remote. Note Do not use old or different types of batteries together. Step 2 Connect the antenna cable (not supplied) to 8 (antenna input) at the rear of the TV. Tip You can also connect your TV to other optional components (see page 24). Step 3 b Plug in the power cord, then press! on the TV to turn it on. Note The 1 (standby) indicator flashes green for a few seconds when turning on the TV. This does not indicate a malfunction. Step 4 Set up the TV by following the instructions of the Initial Setup menu (see page 7). 6 Installation

Installation x Setting up your TV ( Initial Setup ) When you turn on your TV for the first time, the Initial Setup menu will appear. You may change the menu language, preset the TV channels automatically and adjust the picture position using the buttons on the top control panel. Tip The MENU, and V/v/B/b buttons on the remote control can also be used for the operations below. 1 Press 2 +/ to select the desired menu language, then press t. The selected menu language appears. 2 3 4 Press 2 +/ to select Yes, then press t to preset the channels automatically or select No to skip automatic channel presetting. Once you select Yes, your TV will start searching for all the available channels. If the message No channel found. Please connect cable/antenna. appears, check your TV connections, then press t. Press 2 +/ to adjust the bars on the top and bottom of the menu if they are slanted, then press t (KV-AR21M61 for Malaysia only). If no adjustment is necessary, then press t. Press 2 +/ to select No, then press t. This menu will not appear again the next time you turn on the TV by pressing!. To allow this menu to appear again, select Yes, then press t. Start auto program now? Tips You can immediately go to the end of the Initial Setup menu by pressing MENU. You can also set up your TV by pressing the MENU button on the top control panel for about five seconds or using the menu system (see page 14). Installation 7

2 L (MONO) R Overview of Controls x TV top control, front and rear panels TV top control panel SOUND MODE MENU PROG 0 9 8 7 6 TV rear panel 1 Y C B ( MONO) L L ( MONO) TV front panel 2 R CR R qa L (MONO) R qf qd qs 5 4 3 2 1 Button/Terminal Function Page 1! Turn off or turn on the TV. 6 2 Remote control sensor. 3 Wake Up indicator. 20 3 1 Standby indicator. 6 4 i Headphone jack. 5 t2 Video input terminal 2. 24 6 PROG +/ Select program number. 7 2 +/ Adjust volume. 8 t Select TV or video input. 24 Menu operations 7 2 +/ Select and adjust items. 8 t Confirm selected items. 9 MENU Display or cancel the menu. 0 SOUND MODE Select sound mode options with a 5-Band 11 Graphic Equalizer display. qa 8 Antenna input terminal. 24 qs T Monitor output terminal. 25 qd Component video input terminal. 25 qf t1 Video input terminal 1. 24 8 Overview of Controls

Overview of Controls x Using the remote control and basic functions 0 qa qs qd A/B 1 2 3 1 2 qf qg qh 4 5 6 7 8 9 0 PROG 3 4 5 qj MENU 6 qk 7 ql w; wa TV 8 9 Button Description Page 1?/1 Turn off temporarily or turn on the TV. 2 a Display the TV program. 3 Jump to last program number that has been watched for at least five seconds. 4 PROG +/ Select program number. 5 2 +/ Adjust volume. 9 Change the picture size: On (16:9 wide-mode), Off. 0 Display on-screen information. qa Mute the sound. qd t Select TV or video input. 24 qf 0 9, Input numbers. qj Select surround mode options: (KV-AR21M61 only) SRS (three dimensional surround), Simulated (stereo-like monaural sound), Off. (KV-AR14M50 only) On (surround), Simulated (stereo-like monaural sound), Off. continue Overview of Controls 9

continued Button Description Page ql Select sound mode options with a 5-Band Graphic 11 Equalizer display. w; Select picture mode options. 11 Menu operations 6 MENU Display or cancel the menu. 16 7 Confirm selected items. 16 qk V, v, B, b Select and adjust items. 16 Timer operations qg Set TV to turn on automatically. qh Set TV to turn off automatically. Teletext operations (green label) (KV-AR21M61 only) 4, Display the next or previous page. 13 8 Display Teletext broadcast. 13 0 Reveal concealed information. 13 qs Enlarge the Teletext display. 13 qd Stop Teletext display from scrolling. 13 qg Display Teletext service contents. 13 qh Show TV screen while waiting for Teletext page. 13 wa x (red, green, Access a FASTEXT menu. 13 yellow, blue) Stereo/bilingual operations (KV-AR21M61 only) qs A/B Select stereo/bilingual mode. 12 SRS and symbol are trademarks of SRS Labs, Inc. SRS technology is incorporated under license from SRS Labs, Inc. Licensed by BBE Sound, Inc. under USP4638258, 4482866. BBE and BBE symbol are trademarks of BBE Sound, Inc. 10 Overview of Controls

Advanced Operations x Selecting the picture and sound modes You can select picture and sound modes and adjust the setting to your preference in the Personal option. A/B Selecting the picture mode Press to select the desired picture mode. 1 2 3 4 5 6 7 8 9 0 PROG MENU Select Dynamic Standard Soft Personal To view high contrast pictures. normal pictures. mild pictures. the last adjusted picture setting from the Picture Adjustment option in the menu (see page 17). TV Selecting the sound mode Press (or SOUND MODE on the top control panel) to select the desired sound mode with a 5-Band Graphic Equalizer display. Select Dynamic Dynamic To listen to dynamic and clear sound that emphasizes both the low and high tones. Drama 100 300 1k 3k 8k Drama sound that emphasizes voice and high tones. Soft 100 300 1k 3k 8k Soft soft, natural and relaxing sounds. Personal 100 300 1k 3k 8k Personal the last adjusted sound setting from the Sound Adjustment option in the menu (see page 19). 100 300 1k 3k 8k Advanced Operations 11

x Enjoying stereo or bilingual programs B KV-AR21M61 only You can enjoy stereo sound or bilingual programs of NICAM and A2 stereo systems by using the A/B button. When receiving a NICAM program A/B A/B 1 2 3 4 5 6 7 8 9 0 PROG Broadcasting NICAM stereo NICAM bilingual On-screen display (Selected sound) NICAM (Stereo sound) t t Mono (Regular sound) NICAM Main t NICAM Sub t Mono (Main sound) (Sub sound) (Regular sound) t MENU NICAM monaural NICAM Main (Main sound) t Mono (Regular sound) When receiving an A2 program Broadcasting A2 stereo On-screen display (Selected sound) Stereo (Stereo sound) t t Mono (Regular sound) A2 bilingual Main (Main sound) t Sub (Sub sound) t t TV Note If the stereo sound is noisy when receiving a stereo program, select Mono. The sound becomes monaural but the noise is reduced. 12 Advanced Operations

x Viewing Teletext B KV-AR21M61 only Some TV stations broadcast an information service called Teletext which allows you to receive various information, such as stock market reports and news. You can use the buttons on the remote to view Teletext. x (red, green, yellow, blue) A/B 1 2 3 4 5 6 7 8 9 0 PROG MENU TV To Do this display a Teletext Press. Each time you press, the page on the screen changes as follows: TV picture Teletext t Teletext and TV t TV. If there is no Teletext broadcast, 100 is displayed at the top left corner of the screen. check the contents Press. of a Teletext service An overview of the Teletext contents, including page numbers, appears on the screen. select a Teletext page Press the number buttons to enter the three-digit page number of the desired Teletext page. If you make a mistake, reenter the correct page number. To access the next or previous page, press or. hold (pause) a Press to display the symbol at Teletext display the top left corner of the screen. To resume normal Teletext viewing, press. reveal concealed Press. information (e.g., To conceal the information, press the an answer to a quiz) button again. enlarge the Teletext Press. Each time you press, the display Teletext display changes as follows: Enlarge upper half t Enlarge lower half t Normal size. stand by for a Teletext (1) Enter the Teletext page number that page while watching you want to refer to, then press. a TV program (2) When the page number is displayed, press to show the text. select a FASTEXT menu or the colored boxes turn off Teletext Press a. Press x (red, green, yellow and blue) that corresponds to the desired menu or page number. Note The FASTEXT feature can be used only when the FASTEXT broadcast is available. Advanced Operations Advanced Operations 13

Menu Adjustment x Introducing the menu system The MENU button lets you open a menu and change the settings of your TV. The following is an overview of the menu system. Picture icon Sound icon Timer icon Channel Setup icon Setup icon Menu level 1 Setup Language: English Picture Rotation Wide Mode: Video Label Color System: Portable Audio Mode: Select Confirm End Return icon Name of the current menu Menu level 3 Menu level 2 User Guidance Level 1 Level 2 Level 3/Function Page Picture Mode Select the picture mode: Dynamic t Standard t Soft t Personal 17 Picture Adjustment Adjust the Personal option: Picture t Brightness t Color t Hue t Sharpness t Reset Color Temperature Adjust white color tint: Cool t Neutral t Warm VM (KV-AR21M61 only) Sharpen picture definition: High t Low t Off Intelligent Picture Optimize picture quality: On t Off Sound Mode Select the sound mode: Dynamic t Drama t Soft t Personal 18 Sound Adjustment Adjust sound frequency settings of Personal option: Adjust t Reset Balance Select to emphasize the left and right speakers. Intelligent Volume Adjust volume automatically: On t Off Surround Select the surround mode: (KV-AR21M61 only) SRS t Simulated t Off (KV-AR14M50 only) On t Simulated t Off 14 Menu Adjustment

Level 1 Level 2 Level 3/Function Page Timer Sleep Timer Set TV to turn off automatically. 20 Wake Up Timer Set TV to turn on automatically. Channel Setup Auto Program Preset channels automatically. 21 Manual Program Preset channels manually. TV System Select the TV system: B/G t I t D/K t M Program Label Label the program number. Program Block Block unwanted programs. Setup Language Change the menu language: English t (Chinese) 23 Picture Rotation (KV-AR21M61 for Malaysia only) Adjust the picture position. Wide Mode Change the picture size: On (16:9 wide-mode) t Off Video Label Label the connected equipment. Color System Select the color system: Auto t PAL t SECAM t NTSC3.58 t NTSC4.43 Portable Audio Mode Select the input connected to your audio equipment: Video1 t Video2 t Off Menu Adjustment 15

How to use the menu 0 PROG MENU Press MENU to display the menu. Picture Mode: Dynamic Picture Adjustment Color Temperature: Cool VM: High Intelligent Picture: On Select Confirm End TV Press V or v to select the desired item. Channel Setup Auto Program Manual Program TV System: Program Label Program Block B/G Select Confirm End Press (or b) to confirm your selection and go to the next level. Channel Setup Auto Program Manual Program TV System: Program Label Program Block Select Confirm B/G End Other menu operations To Adjust the setting value Move to the next/previous menu level Cancel the menu Press V, v, B or b. B or b. MENU. Tips If you want to exit from Menu level 2 to Menu level 1, press V or v until the return icon ( ) is highlighted, then press. The MENU, t and 2 +/ buttons on the top control panel can also be used for the operations above (see page 8). 16 Menu Adjustment

x Changing the Picture setting The Picture menu allows you to adjust the picture settings. 1 2 Press MENU. Make sure the Picture icon ( ) is selected, then press. Picture Mode: Dynamic Picture Adjustment Color Temperature: Cool VM: High Intelligent Picture: On 3 Press V or v to select the desired item (e.g., Mode ), then press. Select Mode Color Temperature VM (Velocity Modulation) (KV-AR21M61 only) Intelligent Picture To Select Confirm choose either Dynamic, Standard, Soft or Personal * (see page 11). adjust white color tint. Choose either Cool (blue tint), Neutral (neutral tint) or Warm (red tint). sharpen picture definition. Choose either High, Low or Off. optimize picture quality. Press V or v to select On, then press. To cancel, select Off, then press. End * You can adjust the setting to your personal preference in the Picture Adjustment, Color Temperature and VM options only when the Personal mode is selected. Adjusting the Picture Adjustment items under Personal mode 1 2 3 Press V or v to select either Picture (contrast), Brightness, Color, Hue (color tones), or Sharpness, then press. Selecting Reset will set your TV to the factory setting. Press V,v,B or b to adjust the setting of your selected item, then press. Repeat the above steps to adjust other items. The adjusted settings will be received when you select Personal. Notes Hue can be adjusted for the NTSC color system only. Reducing Sharpness can also reduce picture noise. Menu Adjustment 17

x Changing the Sound setting 1 2 The Sound menu allows you to adjust the sound settings. Press MENU. Press V or v to select the Sound icon ( ), then press. Sound Mode: Dynamic Sound Adjustment Balance Intelligent Volume: Surround: Off Off 3 Press V or v to select the desired item (e.g., Mode ), then press. Select Mode Balance Intelligent Volume To Select Confirm choose either Dynamic, Drama, Soft or Personal * (see page 11). Press v or B to emphasize the left speaker. Press V or b to emphasize the right speaker. adjust the volume of all program numbers and video inputs automatically. Press V or v to select On, then press. To cancel, select Off, then press. End Surround (KV-AR21M61 only) choose either SRS, Simulated or Off (see page 9). (KV-AR14M50 only) choose either On, Simulated or Off (see page 9). * You can adjust the setting to your personal preference in the Sound Adjustment option only when the Personal mode is selected (see page 19). 18 Menu Adjustment

Adjusting the Sound Adjustment item under Personal mode The 5-Band Graphic Equalizer feature allows you to adjust sound frequency settings of Personal mode in the menu. 1 Make sure that Adjust is selected, then press. Selecting Reset will set your TV to the factory setting. Adjustment: Personal Adjust Reset Select Confirm 100 300 1k 3k 8k End 2 Press B or b to select the desired sound frequency, then press V or v to adjust the setting and press. The adjusted settings will be received when you select Personal. Notes Adjusting higher frequency will affect higher pitched sound and adjusting lower frequency will affect lower pitched sound. You may display the settings directly using the SOUND MODE button on the top control panel (see page 8) or button on the remote control (see page 10). Menu Adjustment 19

x Changing the Timer setting The Timer menu allows you to set TV to turn off and turn on automatically. 1 2 Press MENU. Press V or v to select the Timer icon ( ), then press. Timer Sleep Timer: Off Wake Up Timer: Off Select Confirm End 3 Press V or v to select the desired item (e.g., Sleep Timer ), then press. Select Sleep Timer To set TV to turn off automatically. Press V or v to select the desired period of time (max. of 1 hour and 30 minutes), then press. Wake Up Timer set TV to turn on automatically. Press V or v to select the desired period of time (max. of 12 hours), then press. After the selected length of time, the TV switches on automatically and Wake Up Timer will appear on the screen. The indicator on the TV lights up amber once you set the Wake Up Timer. Notes You can also cancel Sleep Timer and Wake Up Timer by turning off the TV s main power. If no buttons or controls are pressed for more than one hour after the TV is turned on using the Wake Up Timer, the TV automatically goes into standby mode. 20 Menu Adjustment

x Changing the Channel Setup setting 1 2 The Channel Setup menu allows you to preset channels automatically, manually preset channels, select the TV system, label the program number and block unwanted programs. Press MENU. Press V or v to select the Channel Setup icon ( ), then press. Channel Setup Auto Program Manual Program TV System: Program Label Program Block B/G 3 Press V or v to select the desired item (e.g., Auto Program ), then press. Select Auto Program Manual Program TV System To preset channels automatically. Select Confirm manually preset desired channels and channels that cannot be preset automatically (see Presetting channels manually on page 22). select the TV system. Press V or v to select either B/G, I, D/K, or M, then press. End Program Label Program Block label the program number. (1) Select Program and press. Press V or v to select the program number, then press. (2) Select Label and press. Press V or v to select alphanumeric characters for the label, then press. block unwanted programs. (1) Select Program and press. Press V or v to select the program number, then press. (2) Select Block and press, then press V or v to choose either On or Off. If you preset a blocked program number, that program number will be unblocked automatically. Note During automatic channel presetting, your TV screen will indicate B/G, I, D/K, or M (KV-AR14M50 only) and Auto (KV-AR21M61 only) for the TV System. continue Menu Adjustment 21

continued Presetting channels manually 1 After selecting Manual Program, select the program number to which you want to preset a channel. (1) Make sure Program is selected, then press. (2) Press V or v until the program number you want to preset appears on the menu, then press. Select Manual Program Program: TV System: VHF Low Fine: Skip: Confirm 01 B/G Auto Off End 2 3 4 5 Select the desired channel. (1) Make sure either VHF Low, VHF High or UHF is selected, then press. (2) Press V or v until the desired channel s broadcast appears on the TV screen, then press. If the sound of the desired channel is abnormal, select the appropriate TV system. (1) Press V or v to select TV System, then press. (2) Press V or v until the sound becomes normal, then press. If you are not satisfied with the picture and sound quality, you may be able to improve them by using the Fine tuning feature. (1) Press V or v to select Fine, then press. (2) Press V or v to select Manual, then press. (3) Press V,v,B or b until the picture and sound quality are optimal, then press. The + or icon on the menu flashes while tuning. If you want to skip this program number when using PROG +/, you can select the Skip feature. (1) Press V or v to select Skip, then press. (2) Press V or v to select On, then press. To cancel, select Off, then press. 22 Menu Adjustment

x Changing the Setup setting 1 2 The Setup menu allows you to change the menu language, adjust the picture position, change the picture size, label the connected equipment, select the color system and enjoy audio equipment sound. Press MENU. Press V or v to select the Setup icon ( ), then press. Setup Language: English Picture Rotation Wide Mode: Off Video Label Color System: Auto Portable Audio Mode: Off Select Confirm End 3 Press V or v to select the desired item (e.g., Language ), then press. Select To Language change the menu language. Press V or v to select either English or (Chinese), then press. Picture Rotation adjust the picture position when it is not aligned with the TV screen. (KV-AR21M61 for Press B or b to adjust the picture position, then press. Malaysia only) Wide Mode choose either On or Off (see page 9). Video Label label the connected equipment. (1) Select Video Input and press. Press V or v to select the input you want to label, then press. (2) Select Label and press, then press V or v to select the label options: Video 1/Video 2/DVD, VCR, SAT, Game, or Edit *. * You may edit the video label. Press V or v to select alphanumeric characters for the label, then press. Color System Portable Audio Mode select the color system. Press V or v to select either Auto, PAL, SECAM, NTSC3.58 or NTSC4.43, then press. Normally, set this to Auto. enjoy the sound of audio equipment through the TV speakers, while viewing picture from other inputs. Press V or v to select the input connected to your audio equipment: Video1 or Video2, then press. You may change the picture while listening to the fixed audio input. To cancel Portable Audio Mode, select Off or turn off the TV. Menu Adjustment 23

Additional Information x Connecting optional components Connecting to the video input terminal ( t ) TV front panel Audio/Video cable (not supplied) 2 Camcorder L (MONO) R Video game equipment Audio cable (not supplied) Walkman TV rear panel 1 Radio (MONO) L R Y CB C R L R (MONO) Antenna cable (not supplied) Audio/Video cable (not supplied) S Video cable (not supplied) VCR Notes If you connect a VCR to 8 (antenna input), preset the signal output from the VCR to the program number 0 on the TV (see page 22). When both (S video) and (video) for t 1 are connected at the same time, (S video) is automatically selected. To view (video), disconnect the S video cable. 24 Additional Information

Connecting to the monitor output terminal ( T ) TV rear panel 1 Y Audio system CB (MONO) L L (MONO) R CR R Audio/Video cable (not supplied) VCR Connecting to the component video input terminal ( ) TV rear panel 1 Y Component video cable (not supplied) (MONO) L C B L (MONO) R C R R DVD player Audio cable (not supplied) Notes If your DVD player can output interlace and progressive mode signals, select the interlace output when connecting to (component video input) on your TV. Your TV can receive either 525i/60Hz or 625i/50Hz interlace signals. Some DVD player terminals may be labeled differently: Connect Y (green) CB (blue) CR (red) To (on the DVD player) Y CB, PB, Cb or B-Y CR, PR, Cr or R-Y If you select DVD on your TV screen, the signal from the T (monitor output) jacks will not be output properly. This does not indicate a malfunction. Additional Information 25

x Troubleshooting If you find any problem while viewing your TV, please check the following guide. If any problem persists, contact your Sony dealer. Troubleshooting guide Symptom Snowy picture Possible cause The connection is loose or the cable is damaged. The antenna setup is inappropriate. Solutions Check the antenna cable and connection on the TV, VCR and at the wall. Check the antenna setup. Contact a Sony dealer for advice. Page 24 Noisy sound Channel presetting is inappropriate or incomplete. Display the Channel Setup menu and select Manual Program to preset the channel again. 22 Signal transmission is low. Try using a booster. Distorted picture Broadcast signals are too strong. Turn off or disconnect the booster if it is in use. Noisy sound Good picture The TV system setting is inappropriate. Display the Channel Setup menu and select the appropriate TV System. 22 Noisy sound No picture The power cord, antenna or VCR is not connected. Check the power cord, antenna and VCR connections. 24 No sound The TV is not turned on. Press?/1 (power). Press! (main power) on the TV to turn off the TV for about five seconds, then turn it on again. 9 8 26 Additional Information

Symptom Possible cause Solutions Page Good picture The volume level is too Press 2 + to increase the volume level. 9 low. The sound is muted. Press to cancel the muting. 9 No sound No sound or inappropriate sound Dotted lines or stripes The Portable Audio Mode is functioning. There is local interference from cars, neon signs, hair dryers, power generators, etc. Display the Setup menu and set the Portable Audio Mode to Off. Do not use a hair dryer or other equipment near the TV. Check the antenna setup. Contact a Sony dealer for advice. 23 Double images or ghosts Broadcast signals are reflected by nearby mountains or buildings. Use a highly directional antenna. Use the fine tuning ( Fine ) function. 22 The antenna setup is inappropriate. Check the antenna setup. Contact a Sony dealer for advice. Use of a booster is inappropriate. Turn off or disconnect the booster if it is in use. No color The color level setting is too low. Display the Picture menu and select Personal of Mode, then adjust the Color level in Picture Adjustment. 17 The color system setting is inappropriate. Display the Setup menu and check the Color System setting (usually set this to Auto ). 23 The antenna setup is inappropriate. Check the antenna setup. Contact a Sony dealer for advice. Picture slant Good morning! The magnetic disturbance from external speakers or other equipment, or the direction of the earth s magnetic field may affect the TV. Keep external speakers or other electrical equipment away from the TV. Display the Setup menu and adjust Picture Rotation so that the picture position is optimal (KV-AR21M61 for Malaysia only). 23 continue Additional Information 27

continued Symptom Abnormal color patches TV cannot receive stereo broadcast sound. or Stereo broadcast sound switches on and off or is distorted. (KV-AR21M61 only) 100 appears at the top left of screen and there is no teletext display (KV-AR21M61 only). Teletext display is incomplete (snowy picture or double images) (KV-AR21M61 only). The 1 (standby) indicator on your TV flashes red several times after every three seconds. Possible cause The magnetic disturbance from external speakers or other equipment, or the direction of the earth s magnetic field may affect the TV. The connection is loose or the cable is damaged. The antenna setup is inappropriate. The channel carries no Teletext broadcast. Connection is loose or the cable is damaged. The antenna setup is inappropriate. Signal transmission is too low. Your TV s selfdiagnosis function indicates the possible problems. Solutions Keep external speakers or other equipment away from the TV. Do not move the TV while the TV is turned on. Press! (main power) on the TV to turn off the TV for about 15 minutes, then turn it on again to demagnetize the TV. Check the antenna cable and connection on the TV, VCR and at the wall. Check the antenna setup. Contact a Sony dealer for advice. Check the antenna cable and connection on the TV, VCR, and at the wall. Check the antenna setup. Contact a Sony dealer for advice. Try using a booster. Use the fine tuning ( Fine ) function. Count the number of times the 1 (standby) indicator flashes. Press! (main power) to turn off your TV. Contact your nearest Sony service center. Page 24 13 24 22 28 Additional Information

Symptom Possible cause Solutions Page TV cabinet creaks. A small boom sound is heard when the TV is turned on. Changes in room temperature sometimes make the TV cabinet expand or contract, causing a noise. This does not indicate a malfunction. The TV s demagnetizing function is working. This does not indicate a malfunction. Additional Information 29

110-240220-240 2

3

x B KV-AR21M61 20 3.8 1 2 4

6 7 24 26 8 9 11 KV-AR21M61 12 KV-AR21M61 13 CT MENU 14 17 18 20 21 23 5

x 1 b 2 8 24 3 b! 1 4 Initial Setup 7 6

x 1 MENU V v B b 2 +/ t 2 3 4 2 +/ t t 2 +/ t KV-AR21M61 t 2 +/ t! t MENU MENU 14 7

2 L (MONO) R x SOUND MODE MENU PROG 0 9 8 7 6 1 Y C B ( MONO) L L ( MONO) L 2 (MONO) 5 R 4 3 2 1 qf R qd CR R qs qa 1! 6 2 3 20 3 1 6 4 i 5 t2 2 24 6 PROG +/ 7 2 +/ 8 t 24 7 2 +/ 8 t 9 MENU 0 SOUND MODE 5-Band Graphic Equalizer 11 qa 8 24 qs T 25 qd DVD 25 qf t1 1 24 8

x 0 qa qs qd A/B 1 2 3 1 2 qf 4 5 6 7 8 9 qg qh 0 PROG 3 4 5 qj MENU 6 qk 7 ql w; wa TV 8 9 1? 1 2 a 3 4 PROG +/ 5 2 +/ 9 16:9 0 qa qd t 24 qf 0 9 - qj KV-AR21M61 SRS KV-AR14M50 9

ql 5-Band Graphic Equalizer 11 w; 11 6 MENU 16 7 16 qk V, v, B, b 16 qg qh KV-AR21M61 4, 13 8 13 0 13 qs 13 qd 13 qg 13 qh 13 wa x FASTEXT 13 KV-AR21M61 qs A/B 12 SRS SRS Labs, Inc. SRS SRS Labs, Inc. BBE 4638258, 4482866 BBE BBE BBE 10

x A/B 1 2 3 4 5 6 7 8 9 0 PROG MENU 17 TV SOUND MODE 5-Band Graphic Equalizer 100 300 1k 3k 8k 100 300 1k 3k 8k 100 300 1k 3k 8k 19 100 300 1k 3k 8k 11

x B KV-AR21M61 A/B NICAM A2 A/B A/B 1 2 3 4 5 6 7 8 9 0 PROG t t t t MENU t t TV t A2 A2 t t t t A2 12

x B KV-AR21M61 A/B 1 2 3 4 5 6 7 8 9 0 PROG t t 100 x TV MENU t t FASTEXT (1) (2) x a FASTEXT FASTEXT 13

MENU x MENU KV-AR21M61 17 t t t t t t t t t t t t t 18 t t t t t KV-AR21M61 SRS t t KV-AR14M50 t t 14 MENU

20 Language KV- AR21M61 16:9 21 B/G t I t D/K t M 23 English t t t PAL t SECAM t NTSC3.58 t NTSC4.43 1 t 2 t MENU 15

0 PROG MENU MENU TV V v b V v B b B b MENU V v MENU t 2 +/ 8 16 MENU

x 1 MENU 2 t«g 3 V v * 11 KV-AR21M61 V v * 1 2 V v V, v, B b 3 NTSC MENU 17

x 1 MENU 2 V v 3 V v * 11 v B V b V v KV-AR21M61 SRS 9 KV-AR14M50 9 * 19 18 MENU

5-Band Graphic Equalizer 5 1 100 300 1k 3k 8k 2 B bv v SOUND MODE 8 10 MENU 19

x 1 MENU 2 V v 3 V v V v 1 30 V v 12 20 MENU

x 1 MENU 2 V v 3 V v 22 V v B/G I D/K M 1 V v 2 V v 1 V v 2 V v B/G I D/K M KV-AR14M50KV-AR21M61 MENU 21

1 1 01 B/G 2V v 2 1VHF VHF UHF 2V v 3 1V v 2V v 4 1V v 2V v 3V v B b + 5 PROG +/ 1V v 2V v 22 MENU

x 1 MENU 2 V v 3 V v /Language Language V venglish KV-AR21M61 B b 16:9 9 1 V v 2 V v 12 DVD * V v V v PAL SECAM NTSC 3.58 NTSC 4.43 V v 1 2 MENU 23

x t 2 L (MONO) R 1 Y CB (MONO) L R C R L R (MONO) S 8 022 S t1 S S 24

T 1 Y CB (MONO) L L (MONO) R CR R DVD (MONO) L 1 Y C B L (MONO) DVD R C R R DVD Y CB CR DVD Y CB, PB, Cb B-Y CR, PR, Cr R-Y DVD DVD DVD 525i/60 625i/50 DVD DVD T 25

x Sony 24 Sony 22 22 24?/1! 9 8 26

2 + 9 9 23 Sony 22 Sony 17 23 Sony KV-AR21M61 23 Good morning! 27

! 15 24 Sony KV-AR21M61 100 KV-AR21M61 13 24 KV-AR21M61 Sony 22 1 1! Sony 28

AMARAN TV anda bervoltan tinggi yang membahayakan. Voltan pengendalian TV: 110 240 V AC (untuk Malaysia sahaja: 220 240 V AC). Jangan sambungkan palam wayar kuasa TV sebelum anda selesai membuat semua sambungan yang lain; jika tidak, kebocoran arus yang minimum mungkin mengalir menerusi antena dan terminal lain ke bumi. Untuk mengelakkan kebocoran bateri dan kerosakan alat kawalan jauh, keluarkan bateri dari alat kawalan jauh jika anda tidak menggunakannya untuk beberapa hari. Jika anda tersentuh sebarang cecair yang terbocor dari bateri, sila cuci dengan air secepat mungkin. Untuk keselamatan diri, jangan sentuh manamana bahagian TV, wayar kuasa dan kabel antena semasa kilat. Untuk keselamatan kanak-kanak, jangan biarkan mereka menghampiri TV bersendirian. Jangan benarkan kanak-kanak memanjat TV. Jangan letak sebarang benda di atas TV anda. Jangan dedahkan TV kepada titisan atau percikan cecair dan jangan letak sebarang benda yang mengandungi cecair seperti bekas bunga di atas TV anda. Jangan pasang TV sekiranya terdapat sebarang tumpahan cecair atau pepejal yang terjatuh ke dalamnya. Pemeriksaan segera harus dilakukan oleh orang yang berkelayakan sahaja. Jangan halang ruang pengudaraan TV. Jangan letakkan TV di tempat yang tertutup seperti rak buku atau kabinet. Bersihkan TV dengan kain yang kering dan lembut. Jangan gunakan benzina, pencair atau bahan kimia yang lain untuk membersihkan TV. Jangan lekatkan apa-apa (contohnya, pita pelekat, pita selofan, gam) pada kabinet bercat TV anda. Jangan calarkan tiub gambar. Jangan buka kabinet dan penutup belakang TV kerana terdapat voltan yang tinggi dan bahagian yang merbahaya di dalam TV. Kerja membaiki dan membuang TV hendaklah dilakukan oleh orang yang berkelayakan sahaja. TV anda hanya untuk kegunaan di rumah sahaja. Jangan gunakan TV anda dalam sebarang kenderaan atau di tempat yang amat berhabuk, panas, lembap atau di tempat yang mengalami gegaran yang melampau. 2

Untuk mengelakkan dari berlakunya kebakaran atau litar pintas, jangan dedahkan TV kepada hujan atau kelembapan. Jangan sambungkan terlalu banyak perkakas elektrik kepada satu soket kuasa. Jangan rosakkan wayar. Pasangkan TV di atas rak TV dan lantai yang stabil serta boleh menyokong berat TV anda. Pastikan permukaan rak TV adalah rata dan luasnya adalah lebih besar daripada luas permukaan bawah TV. Pegang palam untuk menarik keluar wayar kuasa TV. Jangan terus tarik wayar kuasa. Walaupun TV anda telah ditutup, TV anda masih bersambung kepada sumber kuasa AC (kuasa utama) selagi wayar kuasa TV disambungkan ke soket. Cabut wayar kuasa TV sebelum memindahkan TV anda atau jika anda tidak menggunakan TV untuk beberapa hari. 3

x Keselamatan TV anda B KV-AR21M61 sahaja Untuk menghindarkan TV anda daripada terjatuh, gunakan skru, pengapit dan pita yang dibekalkan. 20 mm 3.8 mm skru pengapit pita Skrukan pita kepada rak TV dan lubang yang disediakan di bahagian belakang TV anda. atau (1) Masukkan wayar atau rantai menerusi pengapit. (2) Skrukan salah satu pengapit pada dinding atau tiang dan skrukan satu pengapit lagi pada lubang yang disediakan di bahagian belakang TV anda. Nota Gunakan skru yang dibekalkan sahaja. Penggunaan skru yang berlainan jenis boleh merosakkan TV anda. 4

Kandungan Pemasangan Persediaan Awal... 6 Mengaturkan TV anda ( Initial Setup )... 7 Maklumat Tambahan Menyambung komponen pilihan... 24 Penyelesaian masalah... 26 Specifications. Muka surat terakhir Gambaran menyeluruh untuk kawalan Panel kawalan atas, hadapan dan belakang TV... 8 Menggunakan alat kawalan jauh dan fungsi asas... 9 Operasi Lanjutan Memilih mod gambar dan bunyi... 11 Menikmati rancangan stereo atau rancangan dwibahasa (KV-AR21M61 sahaja)... 12 Menonton Teleteks (KV-AR21M61 sahaja)... 13 MY Melaraskan Menu Memperkenalkan sistem menu... 14 Menukar aturan Picture... 17 Menukar aturan Sound... 18 Menukar aturan Timer... 20 Menukar aturan Channel Setup.. 21 Menukar aturan Setup... 23 5

Pemasangan x Persediaan Awal 1 Langkah 1 b Masukkan bateri (dibekalkan) ke dalam alat kawalan jauh. Nota Jangan gunakan bateri lama atau bateri yang berlainan jenis bersama-sama. Langkah 2 Sambungkan kabel antena (tidak dibekalkan) kepada terminal 8 (input antena) yang terdapat di belakang TV anda. Panduan Anda juga boleh menyambungkan komponen pilihan kepada TV anda (rujuk halaman 24). Langkah 3 b Sambungkan wayar kuasa TV, kemudian tekan! pada TV untuk memasangkan TV anda. Nota Penunjuk 1 (standby) berkelip-kelip dengan warna hijau selama beberapa saat apabila anda memasang TV anda. Ini tidak menandakan TV anda mempunyai masalah. Langkah 4 Aturkan TV anda dengan mengikuti arahan menu Initial Setup (rujuk halaman 7). 6 Pemasangan

Pemasangan x Mengaturkan TV anda ( Initial Setup ) Apabila anda memasangkan TV pada kali pertama, menu Initial Setup akan muncul. Anda boleh menukar bahasa menu, mempraset saluran TV secara automatik dan melaraskan kedudukan gambar dengan menggunakan butang pada panel kawalan atas. Panduan Butang MENU, dan V/v/B/b pada alat kawalan jauh juga boleh digunakan untuk operasi di bawah. 1 2 3 4 Tekan 2 +/ untuk memilih bahasa menu yang dikehendaki, kemudian tekan t. Bahasa menu yang dipilih akan muncul. Tekan 2 +/ untuk memilih Yes, kemudian tekan t untuk mempraset saluran secara automatik atau pilih No untuk melangkau fungsi mempraset saluran secara automatik. Apabila anda memilih Yes, TV anda akan mula mencari semua saluran yang ada. Jika mesej No channel found. Please connect cable/antenna. muncul, periksa sambungan TV anda, kemudian tekan t. Tekan 2 +/ untuk melaraskan jaluran di atas dan di bawah menu jika ia senget, kemudian tekan t (KV- AR21M61 untuk Malaysia sahaja). Jika tidak perlu melaraskannya, tekan t. Tekan 2 +/ untuk memilih No, kemudian tekan t. Menu ini tidak akan muncul lagi jika anda memasangkan TV dengan menekan!. Untuk membolehkan menu ini muncul lagi, pilih Yes, kemudian tekan t. Start auto program now? Panduan Anda boleh terus ke paparan menu Initial Setup yang terakhir dengan menekan MENU. Anda juga boleh mengaturkan TV anda dengan menekan butang MENU pada panel kawalan atas lebih kurang lima saat atau menggunakan sistem menu (rujuk halaman 14). Pemasangan 7

2 L (MONO) R Gambaran menyeluruh untuk kawalan x Panel kawalan atas, hadapan dan belakang TV Panel kawalan atas TV SOUND MODE MENU PROG 0 9 8 7 6 Panel belakang TV 1 Y C B ( MONO) L L ( MONO) Panel hadapan TV 2 R CR R qa L (MONO) R qf qd qs 5 4 3 2 1 Butang/Terminal Fungsi Halaman 1! Menutup atau memasang TV. 6 2 Pengesan alat kawalan jauh. 3 Penunjuk Bangun Tidur. 20 3 1 Penunjuk standby. 6 4 i Terminal Headphone. 5 t2 Terminal input video 2. 24 6 PROG +/ Memilih nombor rancangan. 7 2 +/ Melaraskan paras bunyi. 8 t Memilih input TV atau video. 24 Operasi Menu 7 2 +/ Memilih dan melaraskan butiran. 8 t Mengesahkan butiran yang dipilih. 9 MENU Memapar atau membatalkan menu. 0 SOUND MODE Memilih pilihan mod bunyi dengan paparan 11 5-Band Graphic Equalizer. qa 8 Terminal input antena. 24 qs T Terminal output monitor. 25 qd Terminal input komponen video. 25 qf t1 Terminal input video 1. 24 8 Gambaran menyeluruh untuk kawalan

Gambaran menyeluruh untuk kawalan x Menggunakan alat kawalan jauh dan fungsi asas 0 qa qs qd qf qg qh qj qk ql w; wa A/B 1 2 3 4 5 6 7 8 9 0 PROG MENU TV 1 2 3 4 5 6 7 8 9 Butang Deskripsi Halaman 1?/1 Menutup sementara atau memasangkan TV. 2 a Memaparkan input TV. 3 Kembali kepada nombor rancangan sebelumnya yang telah ditonton sekurang-kurangnya lima saat. 4 PROG +/ Memilih nombor rancangan. 5 2 +/ Melaraskan paras bunyi. 9 Menukar saiz gambar: On (16:9 mod lebar), Off. 0 Memaparkan maklumat dalam skrin. qa Menghilangkan bunyi. qd t Memilih input TV atau video. 24 qf 0 9, Input nombor. qj Memilih mod bunyi keliling: (KV-AR21M61 sahaja) SRS (bunyi keliling tiga dimensi), Simulated (bunyi mono ala stereo), Off. (KV-AR14M50 sahaja) On (penguat bunyi pawagam), Simulated (bunyi mono ala stereo), Off. bersambung Gambaran menyeluruh untuk kawalan 9

sambungan Butang Deskripsi Halaman ql Memilih pilihan mod bunyi dengan paparan 11 5-Band Graphic Equalizer. w; Memilih mod gambar. 11 Operasi Menu 6 MENU Memapar atau membatalkan menu. 16 7 Mengesahkan butiran yang dipilih. 16 qk V, v, B, b Memilih dan melaraskan butiran. 16 Operasi pemasa qg Setkan TV supaya dipasang secara automatik. qh Setkan TV supaya ditutup secara automatik. Operasi Teleteks (label hijau) (KV-AR21M61 sahaja) 4, Memaparkan halaman Teleteks yang sebelumnya atau selepasnya. 13 8 Memaparkan Teleteks. 13 0 Memaparkan maklumat yang tersembunyi. 13 qs Membesarkan paparan Teleteks. 13 qd Menghentikan halaman Teleteks. 13 qg Mengetahui kandungan paparan Teleteks. 13 qh Menunjukkan skrin TV sambil menunggu halaman 13 Teleteks. wa x (merah, hijau, Mendapatkan halaman Teleteks yang menggunakan 13 kuning, biru) FASTEKS. Operasi stereo/dwibahasa (KV-AR21M61 sahaja) qs A/B Memilih mod stereo/dwibahasa. 12 Perkataan SRS dan simbol adalah cap dagang SRS Labs, Inc. Teknologi SRS adalah digabungkan di bawah lesen SRS Labs, Inc. Dilesenkan oleh BBE Sound, Inc. di bawah USP4638258, 4482866. Perkataan BBE dan simbol BBE adalah cap dagang BBE Sound, Inc. 10 Gambaran menyeluruh untuk kawalan

Operasi Lanjutan x Memilih mod gambar dan bunyi Anda boleh memilih mod gambar dan bunyi serta melaraskan aturan mengikut citarasa anda dalam pilihan Personal. Memilih mod gambar Tekan sehingga anda menerima mod gambar yang dikehendaki. A/B 1 2 3 4 5 6 7 8 9 0 PROG MENU Pilih Dynamic Standard Soft Personal Untuk menonton gambar dengan beza jelas tinggi. gambar biasa. gambar yang lembut. aturan gambar yang terakhir yang dilaraskan dengan menggunakan pilihan Picture Adjustment dalam menu (rujuk halaman 17). TV Memilih mod bunyi Tekan (atau SOUND MODE pada panel kawalan atas) untuk memilih mod bunyi yang dikehendaki dengan paparan 5-Band Graphic Equalizer. Pilih Dynamic Dynamic Untuk mendengar bunyi yang dinamik dan jelas yang menekankan nada tinggi dan rendah. Drama 100 300 1k 3k 8k Drama bunyi yang menekankan suara dan nada tinggi. Soft 100 300 1k 3k 8k Soft bunyi yang lembut, semula jadi dan menenangkan. Personal 100 300 1k 3k 8k Personal aturan bunyi yang terakhir yang dilaraskan dengan menggunakan pilihan Sound Adjustment dalam menu (rujuk halaman 19). 100 300 1k 3k 8k Operasi Lanjutan 11

x Menikmati rancangan stereo atau rancangan dwibahasa B KV-AR21M61 sahaja Anda boleh menikmati bunyi stereo atau rancangan dwibahasa daripada sistem stereo NICAM dan A2 dengan menggunakan butang A/B. Apabila menerima rancangan NICAM A/B A/B 1 2 3 4 5 6 7 8 9 0 PROG Siaran Paparan di skrin (Bunyi yang dipilih) NICAM stereo NICAM dwibahasa NICAM (Bunyi stereo) t t Mono (Bunyi biasa) NICAM Main t NICAM Sub t Mono (Bunyi utama) (Bunyi Sub) (Bunyi biasa) t MENU NICAM monaural NICAM Main (Bunyi utama) t Mono (Bunyi biasa) Apabila menerima rancangan A2 Siaran Paparan di skrin (Bunyi yang dipilih) A2 stereo Stereo (Bunyi stereo) t t Mono (Bunyi biasa) A2 dwibahasa Main (Bunyi utama) t Sub (Bunyi sub) t t TV Nota Jika bunyi stereo bising semasa menerima rancangan stereo, pilih Mono. Bunyi akan berubah menjadi mono, tetapi bunyi bising akan berkurangan. 12 Operasi Lanjutan

x Menonton Teleteks B KV-AR21M61 sahaja Stesen TV menyediakan perkhidmatan maklumat yang dikenali sebagai Teleteks menerusi beberapa saluran TV. Teleteks membolehkan anda menerima pelbagai maklumat terkini seperti pasaran saham atau berita. x (merah, hijau, kuning, biru) Anda boleh menggunakan butang pada alat kawalan jauh untuk menonton Teleteks. A/B 1 2 3 4 5 6 7 8 9 0 TV PROG MENU Untuk Cara memaparkan Tekan. Setiap kali anda tekan, halaman Teleteks skrin akan berubah seperti berikut: pada gambar TV Teleteks t Teleteks dan TV t TV. Jika tiada siaran Teleteks, maklumat 100 akan dipaparkan di sudut kiri atas skrin. mengetahui Tekan. kandungan Gambaran menyeluruh tentang perkhidmatan kandungan Teleteks dan nombor Teleteks halaman muncul di skrin. memilih halaman Tekan butang nombor untuk memasukkan Teleteks nombor halaman tiga angka bagi halaman Teleteks yang dikehendaki. Jika anda tersilap, masukkan semula nombor halaman yang betul. Untuk mendapatkan halaman yang seterusnya atau yang sebelumnya, tekan atau. menahan Tekan untuk memaparkan simbol (menghentikan) di sudut kiri atas skrin. Untuk paparan Teleteks menyambung semula operasi biasa Teleteks, tekan. memaparkan maklumat Tekan. yang tersembunyi Untuk menyembunyikan (contohnya, jawapan semula maklumat itu, tekan butang itu kuiz) sekali lagi. membesarkan Tekan. Setiap kali anda menekan paparan Teleteks, paparan Teleteks akan berubah seperti berikut: Separuh bahagian atas dibesarkan t Separuh bahagian bawah dibesarkan t Saiz biasa. menunggu halaman (1) Masukkan nombor halaman Teleteks Teleteks semasa yang ingin anda rujuk, kemudian menonton rancangan tekan. TV (2) Apabila nombor halaman dipaparkan, tekan untuk memaparkan teks itu. pilih menu FASTEKS Tekan x (merah, hijau, kuning, biru) atau kotak berwarna yang selaras dengan menu atau muka surat yang dikehendaki. menutup Teleteks Tekan a. Nota Fungsi FASTEKS hanya boleh digunakan apabila terdapat siaran FASTEKS. Operasi Lanjutan 13

Melaraskan MENU x Memperkenalkan sistem menu Butang MENU membolehkan anda membuka menu dan menukar aturan TV anda. Berikut adalah gambaran menyeluruh tentang sistem menu. Lambang Picture Lambang Sound Lambang Timer Lambang Channel Setup Lambang Setup Menu paras 1 Setup Language: English Picture Rotation Wide Mode: Video Label Color System: Portable Audio Mode: Select Confirm End Lambang kembali Nama menu semasa Menu paras 3 Menu paras 2 Panduan Pengguna Paras 1 Paras 2 Paras 3/Fungsi Halaman Picture Mode Memilih mod gambar: Dynamic t Standard t Soft t Personal 17 Picture Adjustment Melaraskan pilihan Personal : Picture t Brightness t Color t Hue t Sharpness t Reset Color Temperature Melaraskan warna putih: Cool t Neutral t Warm VM (KV-AR21M61 sahaja) Menajamkan kejelasan gambar: High t Low t Off Intelligent Picture Mendapatkan kualiti gambar yang optimum: On t Off Sound Mode Memilih mod bunyi: Dynamic t Drama t Soft t Personal 18 Sound Adjustment Melaraskan seting frekuensi bunyi bagi pilihan Personal : Adjust t Reset Balance Memilih untuk memperkuatkan pembesar suara kiri dan kanan. Intelligent Volume Melaraskan paras bunyi suara automatik: On t Off Surround 14 Melaraskan MENU Memilih kesan bunyi keliling: (KV-AR21M61 sahaja) SRS t Simulated t Off (KV-AR14M50 sahaja) On t Simulated t Off

Paras 1 Paras 2 Paras 3/Fungsi Halaman Timer Sleep Timer Setkan TV supaya ditutup secara automatik. 20 Wake Up Timer Setkan TV supaya dipasang secara automatik. Channel Setup Auto Program Mengatur saluran secara automatik. 21 Manual Program Mengatur saluran secara manual. TV System Menukar system TV: B/G t I t D/K t M Program Label Melabelkan nombor program. Program Block Menyekat program yang tidak dikehendaki. Setup Language Menukar bahasa menu: English t (Bahasa Cina) 23 Picture Rotation (KV-AR21M61 untuk Malaysia sahaja) Melaraskan kedudukan gambar. Wide Mode Menukar saiz gambar: On (16:9 mod lebar) t Off Video Label Melabelkan peralatan yang disambungkan. Color System Menukar sistem warna: Auto t PAL t SECAM t NTSC3.58 t NTSC4.43 Portable Audio Mode Memilih input yang disambungkan kepada peralatan audio anda: Video1 t Video2 t Off Melaraskan MENU 15

Cara menggunakan menu 0 PROG MENU Tekan MENU untuk memaparkan menu. Picture Mode: Dynamic Picture Adjustment Color Temperature: Cool VM: High Intelligent Picture: On Select Confirm End TV Tekan V atau v untuk memilih butiran yang dikehendaki. Channel Setup Auto Program Manual Program TV System: Program Label Program Block B/G Select Confirm End Tekan (atau b) untuk mengesahkan pilihan anda dan pergi ke paras menu yang seterusnya. Channel Setup Auto Program Manual Program TV System: Program Label Program Block Select Confirm B/G End Operasi menu yang lain Untuk Melaraskan kedudukan aturan Pergi ke paras menu yang selepas/ sebelum Membatalkan menu Tekan V, v, B atau b. B atau b. MENU. Panduan Jika anda hendak keluar dari Menu paras 2 dan pergi ke Menu paras 1, tekan V atau v sehingga lambang kembali ( ) dipilih, kemudian tekan. Butang MENU, t dan 2 +/ pada panel kawalan atas boleh juga digunakan untuk operasi di atas (rujuk halaman 8). 16 Melaraskan MENU

x Menukar aturan Picture Menu Picture membenarkan anda menukar aturan gambar. 1 2 Tekan MENU. Pastikan lambang Picture ( ) dipilih, kemudian tekan. Picture Mode: Dynamic Picture Adjustment Color Temperature: Cool VM: High Intelligent Picture: On 3 Select Confirm Tekan V atau v untuk memilih butiran yang dikehendaki (contohnya, Mode ), kemudian tekan. End Pilih Mode Color Temperature VM (Velocity Modulation) (KV-AR21M61 sahaja) Intelligent Picture Untuk memilih Dynamic, Standard, Soft atau Personal * (rujuk halaman 11). melaraskan warna putih. memilih Cool (warna biru), Neutral (warna neutral) atau Warm (warna merah). menajamkan kejelasan gambar. memilih High, Low atau Off. mengoptimumkan kualiti gambar. Tekan V atau v untuk memilih On, kemudian tekan. Untuk membatalkannya, pilih Off, kemudian tekan. * Anda boleh melaraskan seting mengikut citarasa anda dalam pilihan Picture Adjustment, Color Temperature dan VM hanya apabila mod Personal dipilih. Melaraskan butiran Picture Adjustment di bawah mod Personal 1 2 3 Tekan V atau v untuk memilih Picture (kecerahan), Brightness, Color, Hue (keterangan warna) atau Sharpness, kemudian tekan. Memilih Reset akan mengesetkan TV anda kepada seting kilang. Tekan V,v,B atau b untuk melaraskan seting butiran pilihan anda, kemudian tekan. Ulangi langkah-langkah tersebut di atas untuk melaras butiran lain. Anda dapat menerima aturan yang telah dilaraskan apabila anda memilih Personal. Nota Hue boleh dilaras untuk sistem NTSC sahaja. Anda boleh mengurangkan Sharpness untuk mengurangkan gangguan gambar. Melaraskan MENU 17