-685-750- () Trinitron Color TV Operating Instructions Before operating the unit, please read this manual thoroughly and retain it for future reference. Panduan Pengendalian Sebelum mengendalikan unit, sila baca buku panduan ini dengan teliti dan simpan untuk rujukan masa depan. GB CT MY KV-AZ 006 Sony Corporation M6
WANING Dangerously high voltages are present inside the TV. TV operating voltage: 0 40 V AC. Do not plug in the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground. To avoid battery leakage and damage to the remote, remove the batteries from the remote if you are not going to use it for several days. If any liquid leaks from the batteries and touches your skin, immediately wash it away with water. For your own safety, do not touch any part of the TV, the power cord and the antenna cable during lightning storms. For children s safety, do not leave children alone with the TV. Do not allow children to climb onto it. To prevent fire or shock hazard, do not expose the TV to rain or moisture. Do not place any objects on the TV. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. Do not operate the TV if any liquid or solid object falls into it. Have it checked immediately by qualified personnel only. Install the TV on a stable TV stand and floor which can support the TV set weight. Ensure that the TV stand surface is flat and its area is larger than the bottom area of the TV. Do not block the ventilation openings of the TV. Do not install the TV in a confined space, such as a bookcase or built-in cabinet. Your TV is recommended for home use only. Do not use the TV in any vehicle or where it may be subject to excessive dust, heat, moisture or vibrations. Do not plug in too many appliances to the same power socket. Do not damage the power cord. Do not open the cabinet and the rear cover of the TV as high voltages and other hazards are present inside the TV. efer servicing and disposal of the TV to qualified personnel. Clean the TV with a dry and soft cloth. Do not use benzine, thinner, or any other chemicals to clean the TV. Do not attach anything (e.g., adhesive tape, cellophane tape, glue) on the painted cabinet of the TV. Do not scratch the picture tube. Pull the power cord out by the plug. Do not pull the power cord itself. Even if your TV is turned off, it is still connected to the AC power source (mains) as long as the power cord is plugged in. Unplug the TV before moving it or if you are not going to use it for several days.
Table of Contents Getting Started... 4 Setting up your TV ( Initial Setup )... 5 TV top control, front and rear panels... 7 Connecting optional components... 8 Using the remote control and basic functions... 0 Introducing the WEGA GATE navigator... Settings Adjustment... 3 Changing the Picture setting... 4 Changing the Sound setting... 6 Changing the Channel Setup setting... 7 Changing the Setup setting... 9 Viewing Teletext... 0 Enjoying stereo or bilingual programs... Listening to the FM adio... Troubleshooting... 3 Specifications... Back cover GB 3
x Getting Started Step Insert the batteries (supplied) into the remote. b Note Do not use old or different types of batteries together. Step Connect the antenna cable (not supplied) to 8 (antenna input) at the rear of the TV. Tips Your TV can receive both TV and FM radio signals from the appropriate connections through the 8 (antenna input) terminal (see page 8). You can also connect your TV to other optional components (see page 8). Step 3 b Plug in the power cord, then press! on the TV to turn it on. Note The (standby) indicator flashes green for a few seconds when turning on the TV. This does not indicate a malfunction. Initial Setup Language: English Step 4 Set up the TV by following the instructions of the Initial Setup menu (see page 5). Confirm End 4
x Setting up your TV ( Initial Setup ) When you turn on your TV for the first time, the Initial Setup menu will appear. You may change the menu language, preset the TV channels automatically, sort or edit the channels and adjust the picture position using the buttons on the remote control or TV top control panel. Press V or v to select the desired menu language, then press. Initial Setup Language: English The selected menu language appears. Confirm End Press V or v to select Yes, then press to preset the channels automatically. The screen will indicate automatic presetting is in progress. Initial Setup First please connect cable/ antenna Start Auto Program now? Yes No Confirm End After all available channels have been tuned and stored, the Program Sorting/Edit menu appears automatically on the screen. Auto Program Program: TV System: VHF Low 0 Auto 3 To skip automatic channel presetting, select No, then press. If the message No channel found. Please connect cable/antenna appears, check your TV connections, then press. The Program Sorting/Edit menu enables you to sort and edit the channels. a) If you wish to keep the channels in the current condition, press WEGA GATE to exit. b) Press V or v to select the program number with the channel you wish to change. The selected channel will appear on the screen. c) If you wish to store the channels in a different order: ) Press b to enter sorting mode. ) Press V or v to select the new program number position for your selected channel, then press B. Program Sorting/Edit POG Label Skip 0 Off 0 Off 03 Off 04 Off Sorting: Edit: Program Sorting/Edit POG Label Skip 0 0 Off Off 03 0 Off 04 Off Sorting mode Confirm Confirm End Exit Exit continue 5
Setting up your TV ( Initial Setup ) (continued) 4 5 d) If you wish to edit the channels, press to change to edit mode. Press b until the mode that you wish to edit is highlighted: Label, Skip, (block symbol). Then press. ) To label, press V or v to select the alphanumeric characters for the label. Then press. ) To skip the program number, press V or v to select On. Then press. You can skip this program number when using POG +/-. 3) To block unwanted program number, press V or v to select. Then press. e) epeat step b) to d) if you wish to change other channels. Press WEGA GATE to go to the next menu. Press B or b to adjust the bars on the top and bottom of the menu if they are slanted, then press. If no adjustment is necessary, then press. To prevent this Initial Setup menu from appearing again when you turn on the TV by pressing!, press V or v to select No, then press. To allow this menu to appear again, select Yes, then press. Program Sorting/Edit POG Label Skip 0 Off 0 Off 03 Off 04 Off Edit mode Picture otation Initial Setup Confirm Program Sorting/Edit POG Label Skip 0 Off 0 Off 03 Off 04 Off Edit mode Confirm Program Sorting/Edit POG Label Skip 0 Off 0 Off 03 Off 04 Off Edit mode Confirm Confirm Confirm End Display this menu next time? Yes No Exit Exit Exit Tip You can immediately go to the end of the Initial Setup menu by pressing WEGA GATE. 6
L (MONO) x TV top control, front and rear panels TV top control panel WEGA GATE FM POG 0 9 8 7 6 TV rear panel Y TV front panel ( MONO) L CB L ( MONO) C L (MONO) 5 4 3 qf qd qs qa Button/Terminal Function Page! Turn off or turn on the TV. 4 emote control sensor. - 3 Wake Up indicator. 3 Standby indicator. 4 4 i Headphone jack. - 5 t Video input terminal. 8 6 POG +/ program number. - 7 +/ Adjust volume. - 8 t TV or video input. 8 WEGA GATE menu operations 6,7 V,v,B,b and adjust items. 8 Confirm selected items. 9 WEGA GATE Display or cancel WEGA GATE menu. 0 FM Listen to FM radio. qa 8 Antenna input terminal. 8 qs T Monitor output terminal. 9 qd Component video input terminal. 9 qf t Video input terminal. 8 7
x Connecting optional components Connecting to the video input terminal ( t ) TV front panel Audio/Video cable (not supplied) L Camcorder L (MONO) Antenna cable (not supplied) TV, CATV, Satellite or When there is no FM signal TV rear panel Antenna selector FM signal Y C B TV signal Antenna cable (not supplied) ( MONO) L L ( MONO) C Audio/Video cable (not supplied) L VC S Video cable (not supplied) DVD player Notes If you connect a VC to 8 (antenna input), preset the signal output from the VC to the program number 0 on the TV (see page 8). When both (S video) and (video) for t are connected at the same time, (S video) is automatically selected. To view (video), disconnect the S video cable. 8
Connecting to the monitor output terminal ( T ) TV rear panel Y (MONO) L C B C L (MONO) Audio/Video cable (not supplied) L Audio system VC Connecting to the component video input terminal ( ) TV rear panel (MONO) L Y C B C L (MONO) Component video cable (not supplied) Y CB C L Audio cable (not supplied) DVD player Notes If your DVD player can output interlace and progressive mode signals, select the interlace output when connecting to (component video input) on your TV. Your TV can receive either 55i/60Hz or 65i/50Hz interlace signals. The component video terminals on your DVD player are sometimes labeled Y/CB/C, Y/PB/ P, Y/Cb/Cr or Y/B-Y/-Y. If you select DVD on your TV screen, the signal from the T (monitor output) jacks will not be output properly. This does not indicate a malfunction. 9
x Using the remote control and basic functions 0 qa qs qd qf qg qh qj qk ql w; A/B 3 4 5 6 7 8 9 0 ETUN TV POG WEGA GATE 3 4 5 6 7 8 9 Button Description Page?/ Turn off temporarily or turn on the TV. a Display the TV program. 3 Jump to last program number that has been watched for at least five seconds. 4 POG +/ program number. To select quickly, press and hold until the desired program number appears. 5 +/ Adjust volume. 8 Change the picture size: On (6:9 wide-mode), Off. 9 surround mode options: 6 TruSurround, WOW, Simulated, Off. 0 Display on-screen information. qa Mute the sound. qd t TV or video input. 8 qf 0 9 Input numbers. For program numbers 0 and above, enter the second digit within two seconds. ql sound mode options 6 Dynamic with a 5-Band Graphic Equalizer display: Dynamic, Standard, 00 300 k 3k 8k Custom *. Standard 00 300 k 3k 8k Custom * When the Custom mode is selected, you can receive the last adjusted sound settings from the Sound Adjustment option in the menu. 00 300 k 3k 8k w; picture mode options: 4 Vivid, Standard, Custom *. * When the Custom mode is selected, you can receive the last adjusted picture settings from the Picture Adjustment option in the menu. 0
Button Description Page WEGA GATE menu operations 6 Confirm selected items. 7 WEGA GATE Display or cancel WEGA GATE menu. qj V, v, B, b and adjust items. qk ETUN eturn to the previous level. Timer operations qg Set TV to turn on automatically according to the (Wake Up Timer) desired period of time (max. of hours). The indicator on TV lights up amber once you set the wake up timer. If no buttons or controls are pressed for more than one hour after the TV is turned on using the wake up timer, the TV automatically goes into standby mode. qh Set TV to turn off automatically according to the (Sleep Timer) desired period of time (max. of one hour and 30 min.). Teletext operations (green label),,,, All buttons are used for Teletext operations. 0,,,, (red, green, yellow, blue) PIP operations,, V, v, B, b Not function for your TV. Stereo/bilingual operations qs A/B stereo/bilingual mode. WOW, TruSurround, SS and symbol are trademarks of SS Labs, Inc. WOW and TruSurround technologies are incorporated under license from SS Labs, Inc. Licensed by BBE Sound, Inc. under USP463858, 448866. BBE and BBE symbol are trademarks of BBE Sound, Inc.
x Introducing the WEGA GATE navigator WEGA GATE is a gateway that allows you access to preset TV channels, connected external inputs, FM adio mode and Settings menu. WEGA GATE TV TV 0 External Inputs FM adio Settings Confirm TV 0 03 04 05 End Confirm watch the preset TV channels (see page 5) External Inputs External Inputs Video Video DVD End FM adio Confirm select the inputs for the connected equipment (see page 8) FM adio Preset : ---.-- Please setup FM adio Preset -9 Search Fine Exit listen to the FM adio (see page ) How to use WEGA GATE WEGA GATE TV External Inputs FM adio Settings Settings Confirm Picture Picture Mode: Vivid Picture Adjustment Color Temperature: Cool VM: High Intelligent Picture: On Signal Level Indicator: On Confirm End TV 0 0 03 04 05 End change the settings of your TV (see page 3) Confirm () Press WEGA GATE to display or cancel the WEGA GATE menu. (3) Press V or v to select the desired item. TV 0 0 03 04 05 End Confirm WEGA GATE TV External Inputs FM adio Settings Confirm () Press (or b) to confirm your selection or go to the next level. Tip The WEGA GATE, operations above. (4) Press ETUN to move to the previous level. and V,v,B,b buttons on the top control panel can also be used for the
x Settings Adjustment You are able to change the settings of your TV from Settings in WEGA GATE menu. Press WEGA GATE button to display WEGA GATE menu. Press V or v to select Settings and press. The following is an overview of the items that can be adjusted. Picture Picture Mode: Vivid Picture Adjustment Color Temperature: Cool VM: High Intelligent Picture: On Signal Level Indicator: On Confirm End Picture (see page 4) Picture Mode : Vivid Standard Custom Picture Adjustment : Picture, Brightness, Color, Hue, Sharpness, eset Color Temperature : Cool Neutral Warm VM : High Low Off Intelligent Picture : On Off Signal Level Indicator : On Off Sound Sound Mode: Dynamic Sound Adjustment Balance Intelligent Volume: Off Surround: Off Confirm End Sound (see page 6) Sound Mode : Dynamic Standard Custom Sound Adjustment : Adjust, eset Balance Intelligent Volume : On Off Surround : TruSurround WOW Simulated Off Channel Setup Auto Program Manual Program Program Sorting/Edit FM adio Setup Confirm End Channel Setup (see page 7) Auto Program Manual Program Program : 00-99 TV System : B/G I D/K M VHF Low / VHF High / UHF Fine : Auto Manual Signal Booster : Auto Off Program Sorting/Edit FM adio Setup Setup Language: English Picture otation Video Label Color System: Wake Up Timer Beep: Auto On Factory Settings Confirm End Setup (see page 9) Language : English (Chinese) Picture otation Video Label : Video Input, Label Color System : Auto PAL SECAM NTSC3.58 NTSC4.43 Wake Up Timer Beep : On Off Factory Settings : Yes No Note When a feature is dimmed in the menu, it is not selectable. 3
x Changing the Picture setting 3 The Picture menu allows you to adjust settings below. Press WEGA GATE and select Settings. Make sure the Picture icon ( ) is selected, then press. Press V or v to select the desired item (e.g., Picture Mode ), then press. Picture Mode Color Temperature VM (Velocity Modulation) Intelligent Picture To choose either Vivid (bright, contrast and sharp), Standard (normal) or Custom *. adjust white color tint. Choose either Cool (blue tint), Neutral (neutral tint) or Warm (red tint). sharpen the edges of each object. Choose either High, Low or Off. optimize picture quality. Press V or v to select On, then press. To cancel, select Off, then press. Signal Level Indicator display the signal level when the Intelligent Picture is functioning. Intelligent Picture Signal Level indicator will be displayed, followed by picture improvement when you change the program number or the input mode. red amber green (weak) (average) (good) Press V or v to select On, then press. To cancel, select Off, then press. Intelligent Picture is still functioning. * You can adjust the setting to your personal preference in the Picture Adjustment, Color Temperature and VM options only when the Custom mode is selected (see page 5). 4
Adjusting the Picture Adjustment items under Custom mode 3 Press V or v to select either Picture (contrast), Brightness, Color, Hue (color tones) or Sharpness, then press. ing eset will set your TV to the factory settings. Press V,v,B or b to adjust the setting of your selected item, then press. epeat the above steps to adjust other items. The adjusted settings will be received when you select Custom. Notes Hue can be adjusted for the NTSC color system only. educing Sharpness can also reduce picture noise. 5
x Changing the Sound setting 3 The Sound menu allows you to adjust settings below. Press WEGA GATE and select Settings. Press V or v to select the Sound icon ( ), then press. Press V or v to select the desired item (e.g., Sound Mode ), then press. Sound Mode Balance Intelligent Volume To choose either Dynamic (low and high tones), Standard (voice and high tones) or Custom *. Press v or B to emphasize the left speaker. Press V or b to emphasize the right speaker. adjust the volume of all program numbers and video inputs automatically. Press V or v to select On, then press. To cancel, select Off, then press. Surround choose either TruSurround (surround sound that spreads out to the rear of a room), WOW ** (full, deep bass sound), Simulated (stereo-like monaural sound) or Off. * You can adjust the setting to your personal preference in the Sound Adjustment option only when the Custom mode is selected. ** BBE High Definition Sound is fully activated maximizing the sound effect in the WOW mode. Note Intelligent Volume is not selectable when TruSurround is selected. Adjusting the Sound Adjustment items under Custom mode The 5-Band Graphic Equalizer feature allows you to adjust sound frequency settings of Custom mode in the menu. Make sure that Adjust is selected, then press. ing eset will set your TV to the factory settings. Press B or b to select the desired sound frequency, then press V or v to adjust the setting and press. The adjusted settings will be received when you select Custom. Notes Adjusting higher frequency will affect higher pitched sound and adjusting lower frequency will affect lower pitched sound. You may display the settings directly by using button on the remote control (see page 0). 6
x Changing the Channel Setup setting 3 The Channel Setup menu allows you to adjust settings below. Press WEGA GATE and select Settings. Press V or v to select the Channel Setup icon ( ), then press. Press V or v to select the desired item (e.g., Auto Program ), then press. Auto Program Manual Program Program Sorting/Edit FM adio Setup * To preset channels automatically. manually preset desired channels and channels that cannot be preset automatically (see Presetting channels manually in page 8). change the order in which the channels appear on the screen, label the program number, skip the program number and block unwanted programs (see step 3 of the section Initial Setup in page 5). preset up to nine FM radio stations. You can manually preset each FM radio station that can be received in your area and then store the radio frequency of the desired FM radio stations. () Press V or v to select the desired FM radio station position, then press. () Press V or v to search the FM radio stations. Searching stops automatically when a station is tuned in. If the station has a weak signal, press B or b to fine tune the radio frequency manually, then press to store the FM radio station. (3) You may edit the FM radio station label. Press V or v to select alphanumeric characters for the label, then press. (4) epeat steps () through (3) to preset other FM radio stations. * The FM adio Setup feature is only available in FM adio mode. To enable this feature, access to FM adio mode by using WEGA GATE system (see page ) or pressing the FM button on the top control panel (see page 7), then preset your desired FM radio stations according to the steps mentioned above. Notes If you preset a blocked program number, that program number will be unblocked automatically. If you sort a blocked program, that program will remain blocked. continue 7
Changing the Channel Setup setting (continued) Presetting channels manually 3 4 5 After selecting Manual Program, select the program number to which you want to preset a channel. () Make sure Program is selected, then press. () Press V or v until the program number you want to preset appears on the menu, then press. the desired channel. () Make sure either VHF Low, VHF High or UHF is selected, then press. () Press V or v until the desired channel s broadcast appears on the TV screen, then press. If the sound of the desired channel is abnormal, select the appropriate TV system. () Press V or v to select TV System, then press. () Press V or v until the sound becomes normal, then press. If you are not satisfied with the picture and sound quality, you may be able to improve them by using the Fine tuning feature. () Press V or v to select Fine, then press. () Press V or v to select Manual, then press. (3) Press V,v,B or b until the picture and sound quality are optimal, then press. The + or icon on the menu flashes while tuning. If the TV signal is too strong (picture distorted; picture with lines; signal interference) or weak (snowy picture), you may be able to improve the picture quality by setting the Signal Booster feature. () Press V or v to select Signal Booster, then press. () Press V or v to select either Off (for picture distorted; picture with lines; signal interference) or Auto (for snowy picture), then press. 0 8
x Changing the Setup setting 3 The Setup menu allows you to adjust settings below. Press WEGA GATE and select Settings. Press V or v to select the Setup icon ( ), then press. Press V or v to select the desired item (e.g., Language ), then press. To Language change the menu language. Press V or v to select either English or (Chinese), then press. Picture otation Video Label Color System Wake Up Timer Beep Factory Settings adjust the picture position when it is not aligned with the TV screen. Press B or b to adjust the picture position, then press. label the connected equipment. () Video Input and press. Press V or v to select the input you want to label, then press. () Label and press, then press V or v to select the label options: Video / Video / DVD, VC, SAT, Game or Edit *. * You may edit the video label to your favorite name. Press V or v to select alphanumeric characters for the label, then press. select the color system. Press V or v to select either Auto, PAL, SECAM, NTSC3.58 or NTSC4.43, then press. Normally, set this to Auto. allow your TV to emit beeping sound when TV switches on automatically using wake up timer. Press V or v to select On, then press. To cancel, select Off, then press. reset your TV to factory settings. Press and press V or v to select Yes, then press. To cancel, select No, then press. Notes Color system is not selectable in FM adio mode. To ensure the beeping sound can be heard, you must set an appropriate volume level on your TV and make sure the TV is not in mute condition. To stop the beeping sound, press any buttons on the remote control or top control panel. If no button is pressed for three minutes, the beeping sound will automatically go off. 9
x Viewing Teletext Some TV stations broadcast an information service called Teletext which allows you to receive various information, such as stock market reports and news. You can use the buttons on the remote to view Teletext., (red, green, yellow, blue) A/B 3 4 5 6 7 8 9 0 ETUN TV POG WEGA GATE To Do this display a Teletext Press. Each time you press, the page on the screen changes as follows: TV picture Teletext t Teletext and TV t TV. If there is no Teletext broadcast, 00 is displayed at the top left corner of the screen. check the contents Press. of a Teletext service An overview of the Teletext contents, including page numbers, appears on the screen. select a Teletext page Press the number buttons to enter the three-digit page number of the desired Teletext page. If you make a mistake, reenter the correct page number. To access the next or previous page, press or. hold (pause) a Press to display the symbol at Teletext display the top left corner of the screen. To resume normal Teletext viewing, press. reveal concealed Press. information (e.g., To conceal the information, press the an answer to a quiz) button again. enlarge the Teletext Press. Each time you press, the display Teletext display changes as follows: Enlarge upper half t Enlarge lower half t Normal size. stand by for a Teletext () Enter the Teletext page number that page while watching you want to refer to, then press. a TV program () When the page number is displayed, press to show the text. select a FASTEXT Press (red, green, yellow and blue) menu or the colored that corresponds to the desired menu or boxes page number. turn off Teletext Press a. Note The FASTEXT feature can be used only when the FASTEXT broadcast is available. 0
x Enjoying stereo or bilingual programs You can enjoy stereo sound or bilingual programs of NICAM and A stereo systems by using the A/B button. When receiving a NICAM program Broadcasting On-screen display (ed sound) A/B A/B 3 4 5 6 7 8 9 0 POG NICAM stereo NICAM bilingual NICAM monaural NICAM (Stereo sound) t t Mono (egular sound) NICAM Main t NICAM Sub t Mono (Main sound) (Sub sound) (egular sound) t NICAM Main (Main sound) t Mono (egular sound) t ETUN WEGA GATE When receiving an A program Broadcasting On-screen display (ed sound) A stereo Stereo (Stereo sound) t t Mono (egular sound) TV A bilingual Main (Main sound) t Sub (Sub sound) t Note If the stereo sound is noisy when receiving a stereo program, select Mono. The sound becomes monaural, but the noise is reduced.
x Listening to the FM adio You are able to listen to the FM radio stations using your TV. To access to FM adio mode: Press WEGA GATE button and select FM adio (see page ). or Press FM button on the top control panel (see page 7). To exit from FM adio mode: Press WEGA GATE button, select the desired items: TV or External Inputs, then press. the desired TV channel or external inputs and press. or Press FM button on the top control panel. A/B POG +/ V, v, B, b WEGA GATE A/B 3 4 5 6 7 8 9 0 ETUN TV POG WEGA GATE Listening to preset stations 3 Access to FM adio mode. Press WEGA GATE button and select Settings. Preset the desired FM radio stations in FM adio Setup from Channel Setup menu (see page 7). Exit from Channel Setup menu by pressing WEGA GATE button. The selected preset FM radio station number and label will appear on the screen. To select the desired preset FM radio station, press POG +/. Tip You can also use the -9 buttons on the remote control to directly select the desired preset FM radio station. Listening to non-preset stations 3 Access to FM adio mode. Press V or v to search for the desired FM radio station. The preset number and label will not be displayed. If the station has a weak signal, press B or b to fine tune the radio frequency manually. Notes You can only operate V, v, B and b functions using the remote control buttons in FM adio mode. The available radio frequency is only for temporary listening pleasure and cannot be stored in the memory. If the message Please setup FM adio appears, display the Channel Setup menu and select FM adio Setup to preset the desired FM radio stations (see page 7). Note When a FM stereo program has static noise, press A/B until Mono appears. There will be no stereo effect, but the noise will be reduced.
x Troubleshooting If you find any problem while viewing your TV, you can either use the Factory Settings function or check the Troubleshooting guide below. If the problem persists, contact your Sony dealer. Factory Settings function Press the WEGA GATE button. Choose Settings and go to Setup ( ) menu. From Setup menu, select Factory Settings. Then select Yes and press. Your TV will go blank for a few seconds, then the Initial Setup menu will appear. Your TV will be set to factory settings, but certain problems may be solved. Symptom Snowy picture, noisy sound Distorted picture, noisy sound Good picture, noisy sound No picture, no sound Good picture, no sound Dotted lines or stripes Double images or ghosts No color Solutions Check the antenna cable and connection on the TV, VC and at the wall (see page 8). Check the antenna setup. Contact a Sony dealer for advice. Display the Channel Setup menu and select Manual Program to preset the channel again (see page 8). Display the Channel Setup menu and set the Signal Booster to Auto from Manual Program (see page 8). Try using an external booster. Turn off or disconnect the external booster if it is in use. Display the Channel Setup menu and set the Signal Booster to Off from Manual Program (see page 8). Display the Channel Setup menu and select the appropriate TV System from Manual Program (see page 8). Check the power cord, antenna and VC connections (see page 8). Press?/ (power) to turn on the TV (see page 0). Press! (main power) on the TV to turn off the TV for about five seconds, then turn it on again (see page 7). Press + to increase the volume level (see page 0). Press to cancel the muting (see page 0). Do not use a hair dryer or other equipment near the TV. Check the antenna setup. Contact a Sony dealer for advice. Use a highly directional antenna. Use the fine tuning ( Fine ) function (see page 8). Check the antenna setup. Contact a Sony dealer for advice. Turn off or disconnect the external booster if it is in use. Display the Picture menu and select Custom from Picture Mode, then adjust the Color level from Picture Adjustment (see page 5). Display the Setup menu and check the Color System setting (usually set this to Auto ) (see page 9). Check the antenna setup. Contact a Sony dealer for advice. continue 3
Troubleshooting (continued) Symptom Picture slant Abnormal color patches Teletext display is incomplete (snowy picture or double images). Solutions Keep external speakers or other electrical equipment away from the TV. Display the Setup menu and adjust Picture otation so that the picture position is optimal (see page 9). Keep external speakers or other equipment away from the TV. Do not move the TV while the TV is turned on. Press! (main power) on the TV to turn off the TV for about 5 minutes, then turn it on again to demagnetize the TV. Check the antenna cable and connection on the TV, VC and at the wall (see page 8). Check the antenna setup. Contact a Sony dealer for advice. Display the Channel Setup menu and set the Signal Booster to Auto from Manual Program (see page 8). Try using an external booster. Use the fine tuning ( Fine ) function (see page 8). TV cannot receive stereo broadcast sound. or Stereo broadcast sound switches on and off or is distorted. TV cannot receive FM radio station. The (standby) indicator on your TV flashes red several times after every three seconds. The TV screen sometimes goes blank for slightly longer than usual during channel change. TV cabinet creaks. A small boom sound is heard when the TV is turned on. Check the antenna cable and connection on the TV, VC and at the wall (see page 8). Check the antenna setup. Contact a Sony dealer for advice. Connect a separate FM antenna and the TV channel source through an antenna selector (switch) to your TV (see page 8). Count the number of times the (standby) indicator flashes. Press! (main power) to turn off your TV. Contact your nearest Sony service center. The Signal Booster is functioning to detect a weak signal. This does not indicate a malfunction. Changes in room temperature sometimes make the TV cabinet expand or contract, causing a noise. This does not indicate a malfunction. The TV s demagnetizing function is working. This does not indicate a malfunction. 4
0-40
4 5 7 8 0 WEGA GATE 3 4 6 7 9 0 3 CT 3
x b b 8 8 8 8 3! Initial Setup Language: English 4 Initial Setup 5 Confirm End 4
x Initial Setup V v V v 0 3 a) WEGA GATE b) Vv c) ) b ) Vv B POG 0 0 03 04 POG 0 0 03 04 0 5
d) b ) V v ) V v POG +/ 3) V v e) b) d) POG POG POG 4 WEGA GATE B b 5! V v WEGA GATE 6
L (MONO) x WEGA GATE FM POG 0 9 8 7 6 Y ( MONO) L CB L ( MONO) C L (MONO) 5 4 3 qf qd qs qa! 4 3 3 4 4 i 5 t 8 6 POG +/ 7 +/ 8 t 8 WEGA GATE 6, 7 V,v,B,b 8 9 WEGA GATE WEGA GATE 0 FM qa 8 8 qs T 9 qd DVD 9 qf t 8 7
x t L L (MONO) ( MONO) L Y C B L ( MONO) C L S DVD 8 08 S t S S 8
T Y (MONO) L C B C L (MONO) L DVD (MONO) L Y C B C L (MONO) DVD Y CB C L DVD DVD DVD 55i/60 65i/50 DVD Y/CB/C, Y/PB/P, Y/Cb/Cr Y/B-Y/-Y DVDT 9
x 0 qa qs qd qf qg qh qj qk ql w; A/B 3 4 5 6 7 8 9 0 ETUN TV POG WEGA GATE 3 4 5 6 7 8 9? a 3 4 POG +/ 5 +/ 8 6:9 9 6 TruSurroundWOW 0 qa qd t 8 qf 0-9 0 ql 5-Band Graphic Equalizer 6 * 00 300 k 3k 8k 00 300 k 3k 8k * 00 300 k 3k 8k w; 4 * * 0
WEGA GATE 6 7 WEGA GATE WEGA GATE qj V, v, B, b qk ETUN qg qh 30,,,, 0,,,,,, V, v, B, b qs A/B WOW, TruSurround, SS SS Labs, Inc. WOW TruSurround SS Labs, Inc. BBE 463858, 448866 BBE BBE BBE
x WEGA GATE WEGA GATE WEGA GATE 0 0 03 04 05 5 DVD 8 ---.-- -9 3 WEGA GATE WEGA GATE 0 0 03 04 05 () WEGA GATE WEGA GATE (3) V v 0 0 03 04 05 WEGA GATE () b (4) ETUN WEGA GATE V,v,B,b
x WEGA GATE WEGA GATE WEGA GATE V v 4 6 TruSurround WOW 7 00 99 B/G I D/K M VHF/VHF/UHF Language: 9 LanguageEnglish PAL SECAM NTSC3.58 NTSC4.43 3
x 3 WEGA GATE Vv * Vv Vv * 5 4
V v V v B b 3 NTSC 5
x 3 WEGA GATE Vv Vv * vb Vb Vv TruSurroundWOW ** * ** BBE WOW TruSurround 5-Band Graphic Equalizer5 BbVv 0 6
x 3 WEGA GATE Vv Vv 8 5 3 * 9 Vv Vv Bb 3 Vv 4 3 * WEGA GATE FM 7 7
Vv VHF 0 VHFVHFUHF Vv 3 Vv Vv 4 Vv Vv 3VvBb + 5 Vv Vv 8
x 3 WEGA GATE Vv Vv/Language Language VvEnglish Bb Vv Vv DVD * * Vv VvPALSECAM NTSC 3.58NTSC 4.43 Vv Vv 9
x, A/B 3 4 5 6 7 8 9 0 ETUN TV POG WEGA GATE t t 00 t t () () FASTEXT a FASTEXTFASTEXT 0
x A/B NICAM A A/B A/B 3 4 5 6 7 8 9 0 POG t t t t t t t t t t t ETUN WEGA GATE A TV A A
x WEGA GATE FM 7 WEGA GATE FM A/B POG +/ V v B b WEGA GATE A/B 3 4 5 6 7 8 9 0 ETUN TV POG WEGA GATE 3 WEGA GATE 7 WEGA GATE POG +/ 9 Vv Bb 3 VvBb 7 FM A/B
x Sony WEGA GATE ( Settings ) ( Setup ) 8 Sony 8 8 8 8 8?/ 0! 7 + 0 0 Sony 8 Sony 5 9 Sony 3
9!5 8 Sony 8 8 8 Sony 8! Sony 4
x Specifications Power requirements Power consumption (W) Television system Color system Stereo/Bilingual system Teletext language Channel coverage B/G I D/K M 8 (Antenna) Audio output (Speaker) Number of terminal (Video) (Audio) (S Video) (Component Video) i (Headphone) FM adio Tuning ange Intermediate Frequency Picture tube Tube size (cm) Screen size (cm) Dimensions (w/h/d, mm) Mass (kg) 0-40 V AC, 50/60 Hz Indicated on the rear of the TV B/G, I, D/K, M PAL, PAL 60, SECAM, NTSC3.58, NTSC4.43 NICAM Stereo/Bilingual B/G, I, D/K; A Stereo/ Bilingual B/G English, French VHF : E to E /UHF : E to E69 / CATV : S0 to S03, S to S4 UHF : B to B68 /CATV : S0 to S03, S to S4 VHF : C to C, to / UHF : C3 to C57, to 60 / CATV : S0 to S03, S to S4, Z to Z39 VHF : A to A3 /UHF : A4 to A79 / CATV : A-8 to A-, A to W+4, W+6 to W+84 75-ohm external terminal 0 W + 0 W Input: Output: Phono jacks; Vp-p, 75 ohms Input: 3 Output: Phono jacks; 500 mvrms Input: Y: Vp-p, 75 ohms, unbalanced, sync negative C: 0.86 Vp-p, 75 ohms Input: Phono jacks; Y: Vp-p, 75 ohms, sync negative CB: 0.7 Vp-p, 75 ohms C: 0.7 Vp-p, 75 ohms Output: 87.5-08.0 MHz 0.7 MHz Stereo minijack in. 54 Measured diagonally 5 Measured diagonally 589 47 55 7 KV-AZM6 Note Design and specifications are subject to change without notice. 5