2-629-464- (2) Projection TV Operating Instructions Before operating the unit, please read this manual thoroughly and retain it for future reference. Mode d emploi Avant de faire fonctionner cet appareil, lisez attentivement le présent mode d emploi et conservez-le pour toute référence ultérieure. GB F CT Panduan Pengendalian Sebelum mengendalikan unit, sila baca buku panduan ini dengan teliti dan simpan untuk rujukan masa depan. MY,, P A KP-F43 KP-F53 2005 Sony Corporation M96 M9
2
WANING To prevent fire or shock hazard, do not expose the projection TV to rain or moisture. Dangerously high voltages are present inside the projection TV. Do not open the cabinet. efer servicing to qualified personnel only. For general safety: Do not expose the projection TV to rain or moisture. Do not open the rear cover. For safe installation: Do not block the ventilation openings. Do not install the projection TV in hot, humid or excessively dusty places. Do not install the projection TV where it may be exposed to mechanical vibrations. Avoid operating the projection TV at temperatures below 5 C (4 F). If the projection TV is transported directly from a cold to a warm location, or if the room temperature has changed suddenly, the picture may be blurred or show poor color. This is because moisture has condensed on the mirror or lenses inside. If this happens, let the moisture evaporate before using the projection TV. To obtain the best picture, do not expose the screen to direct illumination or direct sunlight. It is recommended to use spot lighting directed down from the ceiling or to cover the windows that face the screen with opaque drapery. It is desirable to install the projection TV in a room where the floor and walls are not of reflecting material. If necessary, cover them with dark carpeting or wall paper. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. For safe operations: Do not operate the projection TV on anything but 0-240 V AC, 50/60 Hz. Do not operate the projection TV if any liquid or solid object falls in it have it checked immediately. Do not keep the projection TV plugged in if you are not going to use it for several days. Even if your projection TV is turned off, it is still connected to the AC power source (mains) as long as the power cord is plugged in. Do not pull the power cord to disconnect the projection TV. Pull it out by the plug. Do not plug in too many appliances to the same power socket. Do not damage the power cord. Do not place any objects on the projection TV. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. Install the projection TV on a stable projection TV stand and floor which can support the projection TV set weight. Ensure that the projection TV stand surface is flat and its area is larger than the bottom area of the projection TV. Do not carry the projection TV holding the screen edges. Caution When using TV games, computers, and similar products with your projection TV, keep the brightness and contrast functions at low settings. If a fixed (non-moving) pattern is left on the screen for long periods of time at a high brightness or contrast setting, the image can be permanently imprinted onto the screen. These types of imprints are not covered by your warranty. Cleaning the Screen To clean the screen with a cloth, please use a cleaning cloth lightly moistened with water. Do not use any type of abrasive pad, alkaline cleaner, scouring powder or solvent, such as alcohol or benzine. As a safety precaution, unplug the projection TV before cleaning it. Do not rub, touch, or tap the surface of the screen with sharp or abrasive items, like a ball point pen or a screw driver. Otherwise, this type of contact may result in a scratched screen. GB 3
WEGA GATE WEGA GATE POG POG WEGA GATE POG WEGA GATE POG Using Your New Projection TV x Install the projection TV For the best picture quality, install the projection TV within the areas below. Optimum viewing area (Horizontal) KP-F43 KP-F53 min..9 m min..7 (6 ft.) (5.6 ft.) 60 60 60 60 min. 2.4 m (8 ft.) Optimum viewing area (Vertical) KP-F43 KP-F53 min..9 m (6 ft.) min. 2.4 m (8 ft.) 20 20 20 20 4 Using Your New Projection TV
Table of Contents Using Your New Projection TV Installation Getting Started... 6 Setting up your projection TV ( Initial Setup )... 7 Overview of Controls Projection TV front, inside the dropdown and rear panels... 9 Using the remote control and basic functions... 0 Advanced Operations Selecting the picture and sound modes... 2 Enjoying the WEGA Theatre Mode with center speaker... 3 Viewing two programs at the same time (KP-F53M96 only)... 4 Displaying multiple programs (KP-F53M96 only)... 5 Enjoying stereo or bilingual programs... 6 Viewing Teletext... 7 Operating optional components... 8 Menu Adjustment Introducing the WEGA GATE navigator... 9 Settings Adjustment... 20 Changing the Picture setting... 22 Changing the Sound setting... 23 Changing the Wide Screen setting... 24 Changing the Multi Picture setting (KP-F53M96 only)... 25 Changing the Channel Setup setting... 26 Changing the Setup setting... 28 Additional Information Connecting optional components... 30 Troubleshooting... 33 Specifications... Back cover GB Using Your New projection TV 5
Installation x Getting Started Step b b Initial Setup anguage: English Insert the batteries (supplied) into the remote. Note Do not use old or different types of batteries together. Step 2 Connect the antenna cable (not supplied) to 8 (antenna input) at the rear of the projection TV. Tip You can also connect your projection TV to other optional components (see page 30). Step 3 Plug in the power cord, then press! on the projection TV to turn it on. Note The (standby) indicator flashes green for a few seconds when turning on the projection TV. This does not indicate a malfunction. Step 4 Set up the projection TV by following the instructions of the Initial Setup menu (see page 7). End: WEGA GATE 6 Installation
Installation x Setting up your projection TV ( Initial Setup ) When you turn on your projection TV for the first time, the Initial Setup menu will appear. You may change the menu language, preset the TV channels automatically, sort or edit the channels and adjust the convergence using the buttons on the remote control or projection TV front panel. Press V or v to select the desired menu language, then press. The selected menu language appears. anguage: Initial Setup English 2 3 Press V or v to select Yes, then press to preset the channels automatically. The screen will indicate automatic presetting is in progress. After all available channels have been tuned and stored, the Program Sorting/Edit menu appears automatically on the screen. To skip automatic channel presetting, select No, then press. If the message No channel found. Please connect cable/antenna appears, check your projection TV connections, then press. The Program Sorting/Edit menu enables you to sort and edit the channels. a) If you wish to keep the channels in the current condition, press WEGA GATE to exit. b) Press V or v to select the program number with the channel you wish to change. The selected channel will appear on the screen. c) If you wish to store the channels in a different order: ) Press b to enter sorting mode. 2) Press V or v to select the new program number position for your selected channel, then press B. Initial Setup End: WEGA GATE First please connect cable/antenna Start Auto Program now? Yes No End: WEGA GATE Auto Program Program: 0 TV System: Auto VHF ow Program Sorting/Edit POG abel Skip 0 Off 02 03 04 Off 05 Off 06 Off Sorting: Edit: Off Off Program Sorting/Edit POG abel Skip 0 Off 02 03 0 04 Off 05 Off 06 Off Sorting mode Off End: WEGA GATE Exit: WEGA GATE Off Exit: WEGA GATE continue Installation 7
continued 4 d) If you wish to edit the channels, press to change to edit mode. Press b until the mode that you wish to edit is highlighted: abel, Skip, (block symbol). Then press. ) To label, press V or v to select the alphanumeric characters for the label. Then press. 2) To skip the program number, press V or v to select On. Then press. You can skip this program number when using POG +/. 3) To block unwanted program number, press V or v to select. Then press. e) epeat step b) to d) if you wish to change other channels. Press WEGA GATE to go to the next menu. Make sure that Yes is selected, then press to start digital quick focus. The convergence adjustment screen appears, and the convergence is automatically adjusted. After the adjustment, the last Initial Setup menu appears automatically on the screen. Program Sorting/Edit POG abel Skip 0 Off 02 03 Off 04 Off 05 Off 06 Off Edit mode Off Program Sorting/Edit POG abel Skip 0 Off 02 03 Off 04 Off 05 Off 06 Off Edit mode Off Program Sorting/Edit POG abel Skip 0 Off 02 03 Off 04 Off 05 Off 06 Off Edit mode Off Initial Setup Exit: WEGA GATE Exit: WEGA GATE Exit: WEGA GATE Start digital quick focus now? Yes No Exit: WEGA GATE 5 To prevent this Initial Setup menu from appearing again when you turn on the projection TV by pressing!, press V or v to select No, then press. To allow this menu to appear again, select Yes, then press. Initial Setup Display this menu next time? Yes No Tip You can immediately go to the end of the Initial Setup menu by pressing WEGA GATE. Notes Convergence can also be adjusted manually using the menu (see page 28). You can also perform the Digital Quick Focus feature using on the front panel. Sound will be muted while the Digital Quick Focus feature is running. 8 Installation
WEGA GATE POG Overview of Controls Overview of Controls x Projection TV front, inside the dropdown and rear panels Projection TV rear panel C 20W MAX 8 Y Y PB/ CB PB/ CB P/ C P/ C (MONO) Inside the drop-down panel 4 (MONO) WEGA GATE 2 3 Projection TV front panel 2 qs qd qf qg qh qj POG qa 0 9 8 7 6 5 4 3 2 Button/Terminal Function Page emote control sensor. 2! Turn off or turn on the projection TV. 6 3 Standby indicator. 6 3 Wake Up indicator. 0 4 POG +/ Select program number. 5 2 +/ Adjust volume. 6 t Select TV or video input. 30 WEGA GATE menu operations 4, 5 V,v,B,b Select and adjust items. 9 7 Confirm selected items. 9 8 WEGA GATE Display or cancel WEGA GATE menu. 9 9 Adjust convergence automatically. 28 0 t4 Video input terminal 4. 30 qa i Headphone jack. qs t, t2, t3 Video input terminal, 2, 3. 30 qd T Monitor output terminal. 30 qf Component video input terminal. 3 qg 2 Component video input terminal 2. 3 qh Center speaker input terminal. 32 qj 8 Antenna input terminal. 30 Overview of Controls 9
x Using the remote control and basic functions qf qg qh qj qk ql w; wa ws WEGA THEATE ETUN VIDEO A/B POG INDEX 2 3 4 5 6 7 8 9 0 OPTION TV POG WEGA GATE 0 Overview of Controls 2 3 4 5 6 7 8 9 0 qa qs qd Button Description Page?/ Turn off temporarily or turn on the projection TV. 2 a Display the TV program. 3 t Select TV or video input. 30 Stereo/bilingual operations 4 A/B Select stereo/bilingual mode. 6 5 POG INDEX Display all preset TV programs. 5 (KP-F53M96 only) WEGA GATE menu operations 6 V, v, B, b Select and adjust items. 9 7 Confirm selected items. 9 8 WEGA GATE Display or cancel the WEGA 9 GATE. qj ETUN eturn to the previous level. 9 9 Change the picture size: 4:3, 6:9 (6:9 wide-mode). 0 Jump to last program number that has been watched for at least five seconds. qa POG +/ Select program number. Timer operations qs (Sleep Timer) qd (Wake Up Timer) Set projection TV to turn off automatically according to the desired period of time (max. of one hour and 30 min.). Set projection TV to turn on automatically according to the desired period of time (max. of 2 hours). The indicator on projection TV lights up amber once you set the wake up timer. If no buttons or controls are pressed for more than two hour after the projection TV is turned on using the wake up timer, the projection TV automatically goes into standby mode. qf Mute the sound. qg Display on-screen information. qh WEGA THEATE Select WEGA Theatre Mode. 3
Overview of Controls Button Description Page qk Select sound mode options. 2 ql Select picture mode options. 2 w; Select surround mode options. 23 wa 0 9 Input numbers. For program numbers 0 and above, enter the second digit within two seconds. ws 2 +/ Adjust volume. TWIN picture operations (KP-F53M96 only),, V, v, B, b All buttons are used for Twin picture operations. 4 Teletext operations (green label),,,, All buttons are used for Teletext operations. 7,,,, (red, green, yellow, blue) Optional components operations VIDEO?/, OPTION, For details, see Operating optional components. 8 N, X, x,., >,, 2 +/ TruSurround, SS and symbol are trademarks of SS abs, Inc. TruSurround technology is incorporated under license from SS abs, Inc. Overview of Controls
Advanced Operations x Selecting the picture and sound modes You can select picture and sound modes and adjust the setting to your preference in the Custom option. WEGA THEATE VIDEO Selecting the picture mode Press to select the desired picture mode. Select To view A/B POG INDEX Vivid contrast and sharp pictures. Standard normal pictures. ETUN WEGA GATE Custom the last adjusted picture setting from the Picture Adjustment option in the menu (see page 22). 2 3 4 5 6 7 8 9 0 Selecting the sound mode Press to select the desired sound mode. Select Dynamic Dynamic To listen to dynamic and clear sound that emphasizes both the low and high tones. Standard sound that emphasizes voice and high tones. Standard Custom Custom the last adjusted sound setting from the Sound Adjustment option in the menu (see page 23). 2 Advanced Operations
x Enjoying the WEGA Theatre Mode with center speaker The WEGA Theatre Mode enables you to enjoy the best picture, sound and surround effect of a cinema from a DVD source. You can use your projection TV speaker as the center speaker of your audio system for optimum vocal enhancement and control its sound volume from the remote of the projection TV. Setting up WEGA Theatre Mode WEGA THEATE WEGA THEATE ETUN VIDEO A/B POG INDEX WEGA GATE. Connect the center speaker terminals of the amplifier to the center speaker input terminal on the projection TV (see page 32). 2. Select the proper video input and center speaker mode from WEGA Theatre Setup menu and turn on (main power) the connected equipment (see page 28). 3. See the table below. If the connected equipment is a Sony audio/video equipment, you can set up the remote to work with the connected equipment (see page 8). 2 +/ 2 3 4 5 6 7 8 9 0 OPTION TV POG To switch to WEGA Theatre Mode Press adjust center 2 +/. speaker volume WEGA THEATE. Be sure to aim the remote control at the projection TV set and connected equipment for about one second after the button is pressed. The connected equipment turns on automatically from standby mode and will start playing (only for Sony audio/ video equipment). The Picture Mode and Sound Mode will switch automatically to Custom and you can adjust the setting to your personal preference (see pages 22 and 23). Notes Be sure to place your projection TV and connected Sony equipment adjacent to each other so that you can control both the projection TV and the connected equipment by using the projection TV s remote control at the same time (see page 8). The WEGA Theatre and center speaker modes are automatically cancelled when you change the program number, video input or turn the projection TV off and on again. When the projection TV is in the center speaker mode, you cannot use the Twin pictures feature, change the surround sound and the Intelligent Volume mode. Some Sony equipment might not respond properly when WEGA THEATE button is pressed. In this case, use the equipment s own remote control. To use the projection TV s speakers as the center speaker, you can also display Center Speaker from Sound menu and select On (see page 23). Advanced Operations 3
x Viewing two programs at the same time 0 8 B KP-F53M96 only With the Twin pictures feature, you can display two different TV program or video input at the same time. VIDEO To Press WEGA THEATE A/B display Twin pictures. To cancel, press the button again. V/v/B/b POG INDEX WEGA ETUN GATE 2 3 4 5 6 7 8 9 0 OPTION TV POG select a program number in the right picture swap the left and right pictures swap sound between the left and right pictures change the screen size of the Twin pictures V or v.. B or b once. A symbol will appear to indicate which screen you are hearing. Hold B to increase the left screen size. Hold b to increase the right screen size. Sound will swap automatically to the screen which is increasing in size. Selecting TV program from TV in WEGA GATE menu (see page 9) using PAP (Picture And Picture) You can select your desired TV program directly from the right picture by using V or v buttons.. Press V or v until the desired program appears on the right picture. 2. Press (or b) to display the right picture in full screen. Notes You cannot change the picture size or swap the two pictures in the PAP mode. Swapping the pictures is not available for HD (high-definition) and DVD input signals in Twin mode. HD and DVD input signals are not available in the right picture. The Twin pictures feature is not available when the projection TV is in the center speaker mode (see page 3) and you cannot set the projection TV to the center speaker mode while viewing the Twin pictures. You can only enjoy stereo sound from the left picture. You cannot change the picture to a video input in the right picture. You can only display a video input, except for HD and DVD input signals, in the right picture by swapping the pictures when a video input is displayed in the left picture. The picture and sound from the T (monitor output) terminals will always be from the left picture, even when you select the sound from the right picture by swapping the sound. Due to different video processors used, it is normal that the picture quality of the right picture might be slightly different from the left picture. 4 Advanced Operations
x Displaying multiple programs B KP-F53M96 only The Program Index feature displays all tuned TV programs scrolling on the screen for direct selection. POG INDEX V/v/ WEGA THEATE VIDEO A/B POG INDEX Press POG INDEX. The current program is displayed on the left. The first tuned program is displayed on the bottom right of the screen, then frozen. It scrolls up and the next program appears on the bottom-right until all tuned programs appear one by one. WEGA ETUN GATE 2 3 4 5 6 7 8 9 0 POG 2 3 Press V or v until the program you want to view is displayed in the frame, then press. To return to scrolling, press V or v again. Press again to enlarge the selected program into the left frame. OPTION TV 4 Press POG INDEX. The selected program is displayed in full screen. 2 3 4 0,, 0 8, 8 Note When displaying multiple programs, only the sound of the left picture is heard. Advanced Operations 5
x Enjoying stereo or bilingual programs You can enjoy stereo sound or bilingual programs of NICAM and A2 stereo systems by using the A/B button. VIDEO When receiving a NICAM program WEGA THEATE Broadcasting On-screen display (Selected sound) A/B A/B POG INDEX NICAM stereo NICAM (Stereo sound) t t Mono (egular sound) ETUN WEGA GATE NICAM bilingual NICAM Main t NICAM Sub t Mono (Main sound) (Sub sound) (egular sound) t 2 3 4 5 6 7 8 9 0 OPTION TV POG NICAM monaural When receiving an A2 program Broadcasting On-screen display (Selected sound) A2 stereo NICAM Main (Main sound) t Stereo (Stereo sound) t t t Mono (egular sound) Mono (egular sound) A2 bilingual Main (Main sound) t Sub (Sub sound) t Note If the stereo sound is noisy when receiving a stereo program, select Mono. The sound becomes monaural but the noise is reduced. 6 Advanced Operations
x Viewing Teletext Some TV stations broadcast an information service called Teletext which allows you to receive various information, such as stock market reports and news. You can use the buttons on the remote to view Teletext. (red, green, yellow, blue), VIDEO WEGA THEATE A/B POG INDEX WEGA ETUN GATE 2 3 4 5 6 7 8 9 0 OPTION TV POG To Do this display a Teletext Press. Each time you press, the page on the screen changes as follows: TV picture Teletext t Teletext and TV t TV. If there is no Teletext broadcast, 00 is displayed at the top left corner of the screen. check the contents Press. of a Teletext service An overview of the Teletext contents, including page numbers, appears on the screen. select a Teletext page Press the number buttons to enter the three-digit page number of the desired Teletext page. If you make a mistake, reenter the correct page number. To access the next or previous page, press or. hold (pause) a Press to display the symbol z at Teletext display the top left corner of the screen. To resume normal Teletext viewing, press. reveal concealed Press. information (e.g., To conceal the information, press the an answer to a quiz) button again. enlarge the Teletext Press. Each time you press, the display Teletext display changes as follows: Enlarge upper half t Enlarge lower half t Normal size. stand by for a Teletext () Enter the Teletext page number that page while watching you want to refer to, then press. a TV program (2) When the page number is displayed, press to show the text. select a FASTEXT Press (red, green, yellow and blue) menu or the colored that corresponds to the desired menu or boxes page number. turn off Teletext Press a. Note The FASTEXT feature can be used only when the FASTEXT broadcast is available. Advanced Operations 7
x Operating optional components You can use the supplied remote to operate Sony audio/video equipment. Setting up the remote to work with other connected equipment While keeping VIDEO?/ pressed, press the corresponding number button for the desired equipment (see the chart below). For example, to operate a Sony 8 mm VC: VIDEO + 8 To control Audio System, x, 2 or 3 0,, 2 or 3 DVD, 2 or 3 4, 5 or 6 VT (Beta), VT2 (8 mm) or VT3 (VHS) 7, 8 or 9 To Press turn on/off VIDEO?/ play stop fast forward/ step forward or rewind/ step backward Hold down VIDEO?/ and press Operating audio/video equipment Press VIDEO @/ or while keeping OPTION pressed, press N, x,., >, X, or 2 +/ (see the chart below). pause N while keeping OPTION pressed. x while keeping OPTION pressed. > or. while keeping OPTION pressed. X while keeping OPTION pressed. Press again to resume normal playback. mute the sound while keeping OPTION pressed. (Audio System, x, 2 or 3 only) adjust volume (Audio System, x, 2 or 3 only) 2 +/ while keeping OPTION pressed. Notes If the equipment does not have a certain function, the corresponding button on the remote will not operate. Some equipment might not respond properly to buttons on projection TV s remote. In this case, use the equipment s own remote control. 8 Advanced Operations
Menu Adjustment x Introducing the WEGA GATE navigator WEGA GATE is a gateway that allows you access to preset TV channels, connected external inputs and Settings menu. WEGA GATE TV External Inputs Settings TV TV 0 02 03 04 05 06 07 End: watch the preset TV channels (see pages 7 and 4) External Inputs External Inputs Video 2 Video 2 3 Video 3 4 Video 4 HD/DVD 2 HD/DVD 2 select the inputs for the connected equipment (see page 29) End: Settings Picture DC-MF: DC250 Picture Mode: Vivid Picture Adjustment 3D-N: Off change the settings of your projection TV (see page 20) End: WEGA GATE How to use WEGA GATE WEGA GATE TV External Inputs Settings TV 0 02 03 04 05 06 07 End: () Press WEGA GATE to display or cancel the WEGA GATE menu. (3) Press V or v to select the desired item. TV 0 02 03 04 05 06 07 End: WEGA GATE TV External Inputs Settings (2) Press (or b) to confirm your selection or go to the next level. (4) Press ETUN to move to the previous level. Tip The WEGA GATE, operations above. and V,v,B,b buttons on the front panel can also be used for the Menu Adjustment 9
x Settings Adjustment You are able to change the settings of your projection TV from Settings in WEGA GATE menu. Press WEGA GATE button to display WEGA GATE menu. Press V or v to select Settings and press. The following is an overview of the items that can be adjusted. Picture DC-MF: DC250 Picture Mode: Vivid Picture Adjustment 3D-N: Off End: WEGA GATE Picture (see page 22) DC-MF : DC250 DC00 Progressive Picture Mode : Vivid Standard Custom Picture Adjustment : Picture, Brightness, Color, Hue, Sharpness, Color Temperature, eset 3D-N : On Off Sound Sound Mode: Dynamic Sound Adjustment Balance 00 Intelligent Volume: Off Surround: Off Center Speaker: Off End: WEGA GATE Sound (see page 23) Sound Mode : Dynamic Standard Custom Sound Adjustment : Treble, Bass, BBE *, eset Balance Intelligent Volume : On Off Surround : TruSurround Simulated Off Center Speaker : On Off Wide Screen Wide Mode: Auto Wide: 4:3 Off Wide Screen (see page 24) Wide Mode : 6:9 4:3 Auto Wide : On Off End: WEGA GATE Multi Picture Twin: Off Swap Program Index Multi Picture (KP-F53M96 only) (see page 25) Twin : On Off Swap Program Index End: WEGA GATE 20 Menu Adjustment
Channel Setup Auto Program Manual Program TV System: B/G Program Sorting/Edit End: WEGA GATE Channel Setup (see page 26) Auto Program Manual Program Program : 00-99 TV System : B/G I D/K M VHF ow / VHF High / UHF Fine : Auto Manual Signal Booster : Auto Off Sensitivity : High ow TV System : B/G I D/K M Program Sorting/Edit Setup anguage: English Convergence WEGA Theatre Setup Game Mode: Off Video abel Color System: Auto Eco Mode: Off End: WEGA GATE Setup (see page 28) anguage : English (Chinese) (Arabic) (Thai) Convergence : Digital Quick Focus, Manual Adjust WEGA Theatre Setup : Direct Input, Speaker Game Mode : On Off Video abel : Video Input, abel Color System : Auto PA SECAM NTSC3.58 NTSC4.43 Eco Mode : On Off S input : Auto Off Factory Settings : Yes No Note When a feature is dimmed in the menu, it is not selectable. * icensed by BBE Sound, Inc. under USP4638258, 4482866. BBE and BBE symbol are trademarks of BBE Sound, Inc. Menu Adjustment 2
x Changing the Picture setting 2 The Picture menu allows you to adjust the picture settings. Press WEGA GATE and select Settings. Make sure the Picture icon ( ) is selected, then press. Picture DC-MF: DC250 Picture Mode: Vivid Picture Adjustment 3D-N: Off 3 Press V or v to select the desired item (e.g., DC-MF ), then press. Select DC-MF To choose either DC250 (for high density pictures), DC00 (reduce flicker on the screen) or Progressive (reduce jitter of any small areas or scanning lines on the screen). Picture Mode choose either Vivid, Standard or Custom * (see page 2). 3D-N End: WEGA GATE improve the picture quality of TV or video if a signal received is weak. Press V or v to select On, then press. To cancel, select Off, then press. * You can adjust the setting to your personal preference in the Picture Adjustment option only when the Custom mode is selected. Adjusting the Picture Adjustment items under Custom mode 2 3 Press V or v to select either Picture (contrast), Brightness, Color, Hue (color tones), Sharpness or Color Temperature (choose either Cool, Neutral or Warm ), then press. Selecting eset will set your projection TV to the factory settings. Press V,v,B or b to adjust the setting of your selected item, then press. epeat the above steps to adjust other items. The adjusted settings will be received when you select Custom. Notes The DC-MF mode is not selectable when using the Program Index feature or when the Game Mode or Twin mode is turned On. The mode is not available for HD (highdefinition) and progressive input signals. Hue can be adjusted for the NTSC color system only. educing Sharpness can also reduce picture noise. The DC-MF logo ( Corporation. 22 Menu Adjustment ) and DC-MF are trademarks of Sony
x Changing the Sound setting 2 The Sound menu allows you to adjust the sound settings. Press WEGA GATE and select Settings. Press V or v to select the Sound icon ( ), then press. Sound DC-MF: Sound Mode: Dynamic Sound Adjustment Balance Intelligent Volume: Off Surround: Off Center Speaker: Off 00 3 Press V or v to select the desired item (e.g., Sound Mode ), then press. Select Sound Mode Balance Intelligent Volume To choose either Dynamic, Standard or Custom * (see page 2). Press v or B to emphasize the left speaker. Press V or b to emphasize the right speaker. End: WEGA GATE adjust the volume of all program numbers and video inputs automatically. Press V or v to select On, then press. To cancel, select Off, then press. Surround Center Speaker choose either TruSurround (surround sound that spreads out to the rear of a room), Simulated (stereo-like monaural sound) or Off. use your projection TV speaker to optimise vocal enhancement. Press V or v to select On, then press. To cancel, select Off, then press. * You can adjust the setting to your personal preference in the Sound Adjustment option only when the Custom mode is selected. Adjusting the Sound Adjustment item under Custom mode 2 3 Press V or v to select either Treble, Bass or BBE (choose either High, ow or Off ), then press. Selecting eset will set your projection TV to the factory settings. Press V, v, B or b to adjust the setting of your selected item, then press. epeat the above steps to adjust other items. The adjusted settings will be received when you select Custom. Menu Adjustment 23
x Changing the Wide Screen setting 2 The Wide Screen menu allows you to view the picture with optimal effect when receiving wide-mode (6:9) picture signal. Press WEGA GATE and select Settings. Press V or v to select the Wide Screen icon ( ), then press. Wide Screen Wide Mode: 4:3 Auto Wide: Off 3 Press V or v to select the desired item (e.g., Wide Mode ), then press. Select To Wide Mode change the size of the picture when receiving wide-mode (6:9) picture signal. Choose 6:9. To restore the normal picture size, select 4:3, then press. End: WEGA GATE Auto Wide display the picture in optimum wide screen automatically when you choose On. To cancel, select Off, then press. Tip You can also change to wide-mode picture size by pressing the control (see page 0). button on the remote Notes Wide Mode is not selectable for HD (080i, 720p) input signals or in the right screen when viewing twin pictures. For HD (080i, 720p) input signals, your projection TV will always display wide mode picture. Auto Wide is only available when receiving 576i, 480p and 480i input signals. 24 Menu Adjustment
x Changing the Multi Picture setting 2 B KP-F53M96 only The Multi Picture menu allows you to view two pictures on the screen at the same time, swap the picture of twin screen and display Program Index. Press WEGA GATE and select Settings. Press V or v to select the Multi Picture icon ( ), then press. Multi Picture Twin: Off Swap Program Index 3 Press V or v to select the desired item (e.g., Twin ), then press. Select Twin To display a different TV program beside the main picture. Press V or v to select On, then press. To cancel, select Off, then press. End: WEGA GATE Swap Program Index swap the left and right pictures of the twin screen. view multiple programs on the sub-screens. To cancel, select Program Index, then press. Tip You can also display or cancel the settings directly by pressing the, or POG INDEX buttons on the remote control (see pages 4 and 5). Menu Adjustment 25
x Changing the Channel Setup setting 2 The Channel Setup menu allows you to preset channels automatically, manually preset channels, select the TV system and sort or edit the channels. Press WEGA GATE and select Settings. Press V or v to select the Channel Setup icon ( ), then press. Channel Setup Auto DC-MF: Program Manual Program TV System: B/G Program Sorting/Edit 3 Press V or v to select the desired item (e.g., Auto Program ), then press. Select Auto Program Manual Program TV System To preset channels automatically. End: WEGA GATE manually preset desired channels and channels that cannot be preset automatically (see Presetting channels manually in page 27). select the TV system. Press V or v to select either B/G, I, D/K or M, then press. Program Sorting/Edit change the order in which the channels appear on the screen, label the program number, skip the program number and block unwanted programs. (see step 3 of the section Initial Setup in page 7). Notes If you preset a blocked program number, that program number will be unblocked automatically. If you sort a blocked program, that program will remain blocked. 26 Menu Adjustment
Presetting channels manually After selecting Manual Program, select the program number to which you want to preset a channel. () Make sure Program is selected, then press. (2) Press V or v until the program number you want to preset appears on the menu, then press. Manual Program Program: TV System: VHF ow Fine: Signal Booster: Sensitivity: 0 B/G Auto Auto High End: WEGA GATE 2 3 4 5 6 Select the desired channel. () Make sure either VHF ow, VHF High or UHF is selected, then press. (2) Press V or v until the desired channel s broadcast appears on the projection TV screen, then press. If the sound of the desired channel is abnormal, select the appropriate TV system. () Press V or v to select TV System, then press. (2) Press V or v until the sound becomes normal, then press. If you are not satisfied with the picture and sound quality, you may be able to improve them by using the Fine tuning feature. () Press V or v to select Fine, then press. (2) Press V or v to select Manual, then press. (3) Press V,v,B or b until the picture and sound quality are optimal, then press. The + or icon on the menu flashes while tuning. If the TV signal is too weak (snowy picture), you may be able to improve the picture quality by setting the Signal Booster feature. () Press V or v to select Signal Booster, then press. (2) Make sure Auto is selected, then press. If the TV signal is too strong (picture distorted; picture with lines; signal interference), select Off, press and go to next step to adjust the Sensitivity. If the TV signal is too strong (picture distorted; picture with lines; signal interference), you may be able to adjust the TV reception sensitivity by setting the Sensitivity feature. () Press V or v to select Sensitivity, then press. (2) Press V or v to select ow, then press. Note Sensitivity is only selectable when Signal Booster is set to Off. Menu Adjustment 27
x Changing the Setup setting 2 3 The Setup menu allows you to change the menu language, adjust the convergence, setup WEGA Theatre Mode, adjust suitable picture setting for video games, label the connected equipment, select the color system, reduce your projection TV power consumption, select the S video input mode and reset your projection TV to factory settings. Press WEGA GATE and select Settings. Press V or v to select the Setup icon ( ), then press. Press V or v to select the desired item (e.g., anguage ), then press. Select anguage Convergence To Setup anguage: English Convergence Wega Theatre Setup Game Mode: Off Video abel Color System: Auto Eco Mode: Off End: WEGA GATE change the menu language. Press V or v to select either English, (Chinese), (Arabic) or (Thai), then press. adjust the convergence. Press V or v to select Digital Quick Focus or Manual Adjust, then press. When you select Digital Quick Focus, convergence is automatically adjusted. When you select Manual Adjust, the cross pattern appears on the screen. () Press V,v,B or b to adjust the red lines until they converge with the green lines, then press. (2) Press V,v,B or b to adjust the blue lines until they converge with the center cross pattern, then press. WEGA Theatre Setup Game Mode setup WEGA Theatre Mode for best picture, sound and surround effect enjoyment of a cinema (see page 3). Press V or v to select Direct Input, then press. Select either Video, Video 2, Video 3, Video 4, HD/DVD or HD/DVD 2 for the connected equipment that you want to view with WEGA Theatre, then press. Select Speaker and press. Normally select MAIN. When you want to use the projection TV s speakers as the center speaker, press V or v to select CENTE IN, then press. adjust the picture setting that is suitable to view video games. Press V or v to select On, then press. To cancel, select Off, then press. 28 Menu Adjustment
Video abel Color System Eco Mode label the connected equipment. () Press V or v to select the input you want to label, then press. (2) Press V or v to select the label options: Video / Video 2 / Video 3 / Video 4 / HD/DVD / HD/DVD 2, VC, SAT, Game or Edit *, then press. * You may edit the video label to your favorite name. Press V or v to select alphanumeric characters for the label, then press. select the color system. Press V or v to select either Auto, PA, SECAM, NTSC3.58 or NTSC4.43, then press. Normally, set this to Auto. reduce power consumption of your projection TV to save energy. Press V or v to select On, then press. When you press or turn on the projection TV, Eco Mode ( ) symbol will appear on the screen for a while. To cancel, select Off, then press. S Input select the S video input mode. Press V or v to select Auto to receive the S video signal automatically when the signals are input through both the (S video input) and (video input) jacks of the same video input channel, then press. Factory Settings To cancel, select Off, then press. reset your projection TV to factory settings. Press and press V or v to select Yes, then press. To cancel, select No, then press. Tip When the Digital Quick Focus feature is performed, manual adjustment values are erased. Notes Adjust convergence about 20-30 minutes after the projection TV is first turned on. Game Mode is available only when receiving signals through the t (video input), (S video input) or (component video input) terminals. When HD (high-definition) or progressive signals are input, Game Mode does not function. Menu Adjustment 29
Additional Information x Connecting optional components Connecting to the video input terminal ( t ) Projection TV drop-down panel 4 (MONO) S Video cable (not supplied) Audio/Video cable (not supplied) Camcorder Projection TV rear panel C 20W MAX 8 Antenna cable (not supplied) Y Y PB/ CB PB/ CB (MONO) P/ C P/ C S Video cable (not supplied) VC 2 3 2 Audio/Video cable (not supplied) DVD Player Notes If you connect a VC to 8 (antenna input), preset the signal output from the VC to the program number 0 on the projection TV (see page 27). When both (S video) and (video) for t or t4 are connected at the same time, (S video) is automatically selected. To view (video), disconnect the S video cable. Connecting to the monitor output terminal ( T ) Projection TV rear panel C 20W MAX 8 (MONO) Y PB/ CB P/ C Y PB/ CB P/ C Audio/Video cable (not supplied) Audio system 2 3 2 VC 30 Additional Information
Connecting to the component video input terminal ( ) Projection TV rear panel C Y 20W MAX 8 Y Component video cable (not supplied) PB/ CB PB/ CB (MONO) 2 3 P/ C P/ C 2 Audio cable (not supplied) DVD player Notes The component video terminals on your DVD player are sometimes labeled Y/CB/C, Y/PB/ P, Y/Cb/Cr or Y/B-Y/-Y. If you select HD/DVD or HD/DVD 2 on your projection TV screen, the signal from the T (monitor output) terminals will not be output properly. This does not indicate a malfunction. Projection TV rear panel C 20W MAX 8 Y PB/ CB Y PB/ CB Component video cable (not supplied) (MONO) P/ C P/ C Audio cable (not supplied) Digital TV receiver 2 3 2 Note If your DTV receiver is equipped with the Y/PB/P output terminals, connect it to the Y/PB/P terminals of (component video input ) or 2 (component video input 2). Tip The TV accepts the following signal formats: Total scanning line Effective scanning line fv (Hz) 25i 080i 50/60 750p 720p 50/60 625p 576p 50 625i 576i 50 525p 480p 60 525i 480i 60 continue Additional Information 3
continued Connecting an amplifier to the center speaker input terminal ( ) If you use an amplifier with a Dolby* surround decoder instead of the projection TV s audio system, you can use the projection TV s speakers as the center speaker for your audio system. Using the speaker cords supplied with the amplifier, connect the center speaker terminals of the amplifier to the (center speaker input) terminals on the projection TV. DVD player Projection TV rear panel C Y PB/ CB 20W MAX 8 Y PB/ CB Component video cable (not supplied) Optical digital cable (not supplied) (MONO) C P/ C P/ C Amplifier 2 20W 3 2 Audio cable (not supplied) Front speaker () ear speaker () Front speaker () ear speaker () Woofer Note If you use the projection TV s speaker as the center speaker and nothing is connected to the center speaker input terminals on the rear of projection TV or the sound source emitted from the amplifier does not contain the center speaker channel, no sound will be heard from the projection TV s speaker. * Dolby is a trademark of Dolby aboratories. 32 Additional Information
x Troubleshooting If you find any problem while viewing your projection TV, you can either use the Factory Settings function or check the Troubleshooting guide below. If the problem persists, contact your Sony dealer. Factory Settings function Press the WEGA GATE button. Choose Settings and go to Setup ( ) menu. From Setup menu, select Factory Settings. Then select Yes and press. Your projection TV will go blank for a few seconds, then the Initial Setup menu will appear. Your projection TV will be set to factory settings, but certain problems may be solved. Symptom Solutions Snowy picture, noisy sound Check the antenna cable and connection on the projection TV, VC and at the wall (see page 30). Check the antenna setup. Contact a Sony dealer for advice. Display the Channel Setup menu and select Manual Program to preset the channel again (see page 27). Display the Channel Setup menu and set the Signal Booster to Auto from Manual Program (see page 27). Try using an external booster. Distorted picture, noisy sound Good picture, noisy sound No picture, no sound Good picture, no sound Dotted lines or stripes Double images or ghosts No color Turn off or disconnect the external booster if it is in use. Display the Channel Setup menu and set the Sensitivity to ow from Manual Program (see page 27). Display the Channel Setup menu and select the appropriate TV System from Manual Program (see page 27). The sound of the right picture is selected when twin pictures are displayed. Press or B, b once (KP-F53M96 only) (see page 4). Check the power cord, antenna and VC connections (see page 30). Press?/ (power) to turn on the projection TV (see page 0). Press! (main power) on the projection TV to turn off the projection TV for about five seconds, then turn it on again (see page 9). Press 2 + to increase the volume level (see page 9). Press to cancel the muting (see page 0). The sound of the right picture is selected when twin pictures are displayed. Press or B, b once (KP-F53M96 only) (see page 4). Do not use a hair dryer or other equipment near the projection TV. Check the antenna setup. Contact a Sony dealer for advice. Use the fine tuning ( Fine ) function (see page 27). Check the antenna setup. Contact a Sony dealer for advice. Turn off or disconnect the external booster if it is in use. Display the Picture menu and select Custom of Picture Mode, then adjust the Color level in Picture Adjustment (see page 22). Display the Setup menu and check the Color System setting (usually set this to Auto ) (see page 29). Check the antenna setup. Contact a Sony dealer for advice. continue Additional Information 33
continued Symptom Abnormal color patches TV cannot receive stereo broadcast sound. or Stereo broadcast sound switches on and off or is distorted. Teletext display is incomplete (snowy picture or double images). The (standby) indicator on your projection TV flashes red several times after every three seconds. The projection TV screen sometimes goes blank for slightly longer than usual during channel change. Cannot play shooting games. Projection TV cabinet creaks. Solutions Keep external speakers or other equipment away from the projection TV. Do not move the projection TV while the projection TV is turned on. Check the antenna cable and connection on the projection TV, VC and at the wall (see page 30). Check the antenna setup. Contact a Sony dealer for advice. Check the antenna cable and connection on the projection TV, VC and at the wall (see page 30). Check the antenna setup. Contact a Sony dealer for advice. Display the Channel Setup menu and set the Signal Booster to Auto from Manual Program (see page 27). Use the fine tuning ( Fine ) function (see page 27). Count the number of times the (standby) indicator flashes. Press! (main power) to turn off your projection TV. Contact your nearest Sony service center. The Signal Booster is functioning to detect a weak signal. This does not indicate a malfunction. Some shooting games which involve pointing a light beam at the projection TV screen with an electronic gun or rifle cannot be used with your projection TV. For details, see the instruction manual supplied with the video game software. Change in room temperature sometimes make the projection TV cabinet expand or contract, causing a noise. This does not indicate a malfunction. Static discharge is felt when touching the projection TV cabinet. ines moving across the projection TV screen. This is the same static discharge that is felt when touching metal door handles or car doors especially when the air is dry, for example in winter. This does not indicate a malfunction. Use the fine tuning ( Fine ) function (see page 27). 34 Additional Information
2
AVETISSEMENT Afin d éviter tout risque d incendie ou d électrocution, n exposez pas le téléviseur de projection à la pluie ou à l humidité. Ce téléviseur de projection fonctionne avec des hautes tensions dangereuses. N ouvrez jamais le châssis de l appareil. Confiez l entretien à un personnel qualifié uniquement. Sécurité: N exposez pas le téléviseur de projection à la pluie ou à l humidité. N ouvrez pas le panneau arrière. Installation: Veillez à ne pas obstruer les orifices de ventilation. N installez pas le téléviseur de projection dans un endroit chaud, humide ou excessivement poussiéreux. N installez pas le téléviseur de projection dans un endroit où il risque d être soumis à des vibrations mécaniques. Evitez de faire fonctionner le téléviseur de projection à des températures inférieures à 5 C. Si vous transportez le téléviseur de projection d un endroit froid à un endroit chaud, ou si la température de la pièce change subitement, l image peut être imprécise ou présenter des couleurs peu nettes. Ceci est dû à la condensation sur le miroir ou l objectif. Si cela se produit, laissez s évaporer la condensation avant d utiliser le téléviseur de projection. Pour obtenir une meilleure image, n exposez pas l écran à la lumière directe et aux rayons du soleil. Il est recommandé d utiliser un projecteur d éclairage au plafond ou de couvrir les fenêtres faisant face à l écran avec des rideaux opaques. Il est également préférable d installer le téléviseur de projection dans un local où le sol et les murs ne sont pas revêtus d un matériau réfléchissant. Si nécessaire, utilisez un tapis foncé ou tapissez la pièce. N installez pas l appareil dans un espace confiné comme dans une bibliothèque ou un meuble encastré. Utilisation: Faites uniquement fonctionner le téléviseur de projection sur une tension de 0-240 V CA 50/60 Hz. Ne faites pas fonctionner le téléviseur de projection si un liquide ou un objet est tombé à l intérieur et faites-le vérifier immédiatement. Ne laissez pas le téléviseur de projection branché sur le secteur si vous prévoyez de ne pas l utiliser pendant plusieurs jours. Même si votre téléviseur de projection est hors tension, il reste raccordé à la source d alimentation secteur tant que le cordon d alimentation est branché. Ne tirez pas sur le cordon d alimentation pour débrancher le téléviseur de projection, mais tirez sur la fiche. Ne branchez pas un nombre trop important d appareils sur la même prise. N endommagez pas le cordon d alimentation. Ne placez aucun objet sur le téléviseur de projection. Cet appareil ne doit pas être exposé à des gouttes d eau ou à des éclaboussures et aucun objet contenant du liquide, comme un vase, ne doit être placé dessus. Installez le téléviseur de projection sur un support et un sol stables en mesure de supporter son poids. Vérifiez que la surface du support est plane et qu elle est plus grande que le socle du téléviseur de projection. Ne transportez pas le téléviseur de projection en le prenant par les bords de l écran. Attention orsque vous utilisez des jeux vidéo, des ordinateurs et d autres produits similaires avec votre téléviseur de projection, maintenez les réglages de luminosité et de contraste sur de faibles valeurs. Si une image fixe (non animée) reste affichée à l écran pendant de longues périodes alors que la luminosité et le contraste sont réglés sur des valeurs élevées, l image peut rester définitivement incrustée sur l écran. Ces types d incrustations ne sont pas couverts par notre garantie car ils résultent d une utilisation inappropriée. Nettoyage de l écran Pour nettoyer l écran avec un chiffon, utilisez le chiffon de nettoyage légèrement imprégné d eau. N utilisez pas d éponge abrasive, de nettoyant alcalin, de poudre à récurer ou de solvant tel que de l alcool ou de la benzine. Par mesure de sécurité, débranchez le téléviseur avant de le nettoyer. Ne frottez pas, ne touchez pas et ne tapotez pas la surface de l écran avec des objets pointus ou abrasifs, tels que la pointe d un stylo ou un tournevis. Vous pourriez en effet rayer l écran. 3
WEGA GATE WEGA GATE POG POG WEGA GATE WEGA GATE POG POG Utilisation de votre nouveau téléviseur de projection x Installation du téléviseur de projection Pour obtenir une image de qualité optimale, installez le téléviseur de projection en respectant le schéma illustré ci-dessous. Zone de visualisation optimale (horizontale) KP-F43 KP-F53 min..9 m min..7 (6 ft.) (5.6 ft.) min. 2.4 m (8 ft.) 60 60 60 60 Zone de visualisation optimale (verticale) KP-F43 KP-F53 min..9 m (6 ft.) min. 2.4 m (8 ft.) 20 20 20 20 4 Utilisation de votre nouveau téléviseur de projection