ES-5104PH Quick Installation Guide 09-2015 / v1.1
Package Contents Product Information Before you start using this switch, please check if there is anything missing in the package, and contact your dealer to claim the missing item(s): ES-5104PH PoE+ Switch Quick Installation Guide Power Adapter Power Cord Rubber Feet Hardware Overview 2
LED Status Power: Green LED LNK/ACT: Green LED (Port 1 - Port 5) PoE: Orange LED (Port 1 Port 4) Max: Orange LED (PoE Overload Alarm) Operating Environment This switch must be installed and operated within the limits of the specified operating temperature 0-40 C (32-104 F) and humidity (10-90% non-condensing). Do not place objects on top of the unit. Do not obstruct any vents at the sides of the unit. Do not position the unit close to any heating source such as a heater, radiator or in direct exposure to sun. Take care to ensure the unit does not come into contact with water. Consider using a dehumidifier to reduce humidity and prevent moisture entering the unit. 3
Connecting to Network Devices The RJ-45 ports on the switch support Auto-MDI/MDI-X which allows either straight-through or cross-over type cables to connect this switch to a workstation or switch. Connect one end of the network cable to the RJ-45 port on the side panel, and connect the other end of the network cable to the RJ-45 port on the network device. Follow the same procedure to connect all RJ-45 ports of the switch. The UTP network cables must comply with EIA/TIA 568 specifications and Category 5 standard for data transmission. The maximum length for a UTP cable segment between the switch and connected devices is 100 meters (300ft). Once the network cable is connected to both ends and the attached network device is powered on, the green LNK/ACT LED should be lit. Connecting The Power Connect the power adapter to the power connector of the unit; the green power LED on the front panel should be lit. 4
5
TROUBLESHOOTING 1. Power LED is not lit. Check if the power cord is properly connected to the external power adapter and the power source. Make sure the DC power jack is firmly plugged into the power socket of the switch. 2. Link/Activity (LNK/ACT) LED is not lit when connected to devices. Ensure that the network device attached to the switch is switched on. Check the network cable; ensure it is properly connected to the switch and the network device. Check the network cable; ensure the UTP cable complied with EIA/TIA 568 and Category 5 specifications. [!] Contact your dealer if problems persist. 6
產品資訊 包裝內容 在您使用本產品前, 請先確認包裝內容物是否如下列, 如有短缺, 請洽原購買經銷商或店家 ES-5104PH 安裝指南 電源變壓器 電源線 橡膠腳墊 硬體概觀 7
LED 指示燈狀態說明 Power: 綠燈 LED LNK/ACT: 綠燈 LED ( 傳輸埠 1 傳輸埠 5) PoE: 橘燈 LED ( 傳輸埠 1 傳輸埠 4) Max: 橘燈 LED (PoE 負載過量警示 ) 操作環境 本產品必須安裝及操作於 0-40 C (32-104 F ) 的操作溫度和 (10-90% non-condensing) 的操作濕度範圍內 請勿在本產品機體上放置他物 請保持本產品機體側邊的散熱孔通風無阻塞 請勿將本產品放置在任何加熱源附近, 如暖爐 散熱器或直接曝曬在太陽下 請小心不要讓本產品碰觸到水 必要時請考慮使用除濕機降低環境濕度, 以防止本產品受潮 8
與上網裝置連接 本產品的 RJ-45 傳輸埠支援 Auto-MDI/MDI-X 功能, 不論是使用 straight-through( 直通型 ) 或 cross-over( 交叉型 ) 網路線來連接工作站或交換器都沒有問題 將網路線的一端連接到本產品的任一 RJ-45 傳輸埠, 在將該網路線的另一端連接到上網裝置的 RJ-45 傳輸埠 接著, 重複相同的步驟來連接本產品所有的 RJ-45 傳輸埠及您的上網裝置 用以進行資料傳輸的 UTP 網路線必須符合 EIA/TIA 568 規格及 Cat. 5 標準 連接本產品和上網裝置之間的 UTP 網路線, 最大長度是 100 公尺 (300ft) 一旦由網路線連接本產品的上網裝置通電時, 綠色的 LNK/ACT 指示燈會亮起 連接電源 當本產品以包裝隨附的電源變壓器連接至電源插座時, 前面板上的綠色電源 LED 指示燈會亮起 9
10
疑難排除 1. 電源 LED 指示燈未亮 請您先檢查電源變壓器是否已正確連接至電源插座 並且請再確認電源變壓器的 DC 直流電源插頭已確實地連接本展品的電源插孔 2. 當上網裝置已連接本產品, 但 Link/Activity (LNK/ACT) LED 指示燈未亮 請確認該上網裝置已啟動 請檢查網路線, 確認它是正確連接本產品和上網裝置 請檢查網路線, 確認它是符合 EIA/TIA 568 和 Cat. 5 規格的 UTP 網路線 [!] 如果問題仍然存在, 請聯繫您購買本產品的經銷商 各地支援 (Local Support) 台灣地區客服專線 :0800-200-115, ( 限市話撥打, 手機請撥打 02-7739-6785) 服務時間 : 週一 ~ 週五 ( 例假日除外 ) 上午 9:00~ 晚上 9:00 客服信箱 : service@edimax.com.tw 中国地区客服专线 : 4006-765-988, 客服信箱 : service@edimax.com.cn Others http://www.edimax.com 11 本手冊所提及之其他公司商標及產品名稱為所屬相關公司所有
COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd. makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability, or fitness for any particular purpose. Any software described in this manual is sold or licensed as is. Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Edimax Technology Co., Ltd. reserves the right to revise this publication and to make changes from time to time in the contents hereof without the obligation to notify any person of such revision or changes. The product you have purchased and the setup screen may appear slightly different from those shown in this QIG. The software and specifications are subject to change without notice. Please visit our website www.edimax.com for updates. All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders. 12
13 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio technician for help. FCC Caution This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. Federal Communications Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 2.5cm (1 inch) during normal operation. Federal Communications Commission (FCC) RF Exposure Requirements SAR compliance has been established in the laptop computer(s) configurations with PCMCIA slot on the side near the center, as tested in the application for certification, and can be used in laptop computer(s) with substantially similar physical dimensions, construction, and electrical and RF characteristics. Use in other devices such as PDAs or lap pads is not authorized. This transmitter is restricted for use with the specific antenna tested in the application for certification. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000. Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment. EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria, Cyprus, Czech, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and Switzerland. EU Countries Not Intended for Use None
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 1995/5/CE, 2009/125/CE, 2006/95/CE, 2011/65/CE. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 1995/5/ES, 2009/125/ES, 2006/95/ES, 2011/65/ES. Polski: Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami określonymi Dyrektywą UE 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.. Română: Acest echipament este în conformitate cu cerinţele esenţiale şi alte prevederi relevante ale Directivei 1995/5/CE, 2009/125/CE, 2006/95/CE, 2011/65/CE. Русский: Это оборудование соответствует основным требованиям и положениям Директивы 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC. Magyar: Ez a berendezés megfelel az alapvető követelményeknek és más vonatkozó irányelveknek (1995/5/EK, 2009/125/EK, 2006/95/EK, 2011/65/EK). Türkçe: Bu cihaz 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC direktifleri zorunlu istekler ve diğer hükümlerle ile uyumludur. Українська: Обладнання відповідає вимогам і умовам директиви 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC. Slovenčina: Toto zariadenie spĺňa základné požiadavky a ďalšie príslušné ustanovenia smerníc 1995/5/ES, 2009/125/ES, 2006/95/ES, 2011/65/ES. Deutsch: Dieses Gerät erfüllt die Voraussetzungen gemäß den Richtlinien 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC. Español: El presente equipo cumple los requisitos esenciales de la Directiva 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC. Italiano: Questo apparecchio è conforme ai requisiti essenziali e alle altre disposizioni applicabili della Direttiva 1995/5/CE, 2009/125/CE, 2006/95/CE, 2011/65/CE. Nederlands: Dit apparaat voldoet aan de essentiële eisen en andere van toepassing zijnde bepalingen van richtlijn 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.. Português: Este equipamento cumpre os requesitos essênciais da Directiva 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC. Norsk: Dette utstyret er i samsvar med de viktigste kravene og andre relevante regler i Direktiv 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC. Svenska: Denna utrustning är i överensstämmelse med de väsentliga kraven och övriga relevanta Dansk: bestämmelser i direktiv 1995/5/EG, 2009/125/EG, 2006/95/EG, 2011/65/EG. Dette udstyr er i overensstemmelse med de væsentligste krav og andre relevante forordninger i direktiv 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC. suomen kieli: Tämä laite täyttää direktiivien 1995/5/EY, 2009/125/EY, 2006/95/EY, 2011/65/EY oleelliset vaatimukset ja muut asiaankuuluvat määräykset. ----------------------------------------------------------------------------------------------------------------------- WEEE Directive & Product Disposal 14 At the end of its serviceable life, this product should not be treated as household or general waste. It should be handed over to the applicable collection point for the recycling of electrical and electronic equipment, or returned to the supplier for disposal.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directives. Equipment: ES-5104PH Ports Model No.: ES-5104PH 5-Port Fast Ethernet Switch with 4 PoE+ The following European standards for essential requirements have been followed: Electromagnetic directive 2004/108/EC EMC : EN55022:2010 Class B EN55024:2010 EN61000-3-2:2006+A1:2009+A2:2009 EN61000-3-3:2008 Safety (LVD) : EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 Edimax Technology Co., Ltd. No. 3, Wu Chuan 3 rd Road, Wu-Ku Industrial Park, New Taipei City, Taiwan Date of Signature: Oct., 2015 Signature: Printed Name: Title: Albert Chang Director Edimax Technology Co., Ltd. 15
16