“注意 - 閱讀操作指示，以減少風險”

PT-0721 Cordless Pocket Screwdriver 7.2V User s Manual 1 st Edition, 2012 2012 Copyright by Prokit s Industries Co., Ltd.

Important! When using equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating manual with care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, give them these operating instructions as well. We accept no liability for damage or accidents which arise due to non-observance of these instructions and the safety information. 1. Safety information Please refer to the booklet included in delivery for the safety instructions. Caution! Read all safety regulations and instructions. Any errors made in following the safety regulations and instructions may result in an electric shock, fire and / or serious injury Keep all safety regulations and instructions in a safe place for future use. 2. Instrument instructions 2.1 Parts instructions 1. Bit chuck 2. Locking sleeve 3. 15+1 adjustable torque setting 4. Two speed control 5. Battery capacity indicator 6. Battery capacity checking button 7. Clockwise/counter-clockwise selector switch 8. Charging socket 9. Operating trigger 10. LED light 2.2 Items supplied Open the packaging and take out the equipment with care. Remove the packaging material and any packaging and/or transportation braces (if available).check to see if all items are supplied. Inspect the equipment and accessories for transport damage. If possible, please keep the packaging until the end of the guarantee period. 2

Important The equipment and packaging material are not toys. Do not let children play with plastic bags, or small parts. There is a danger of swallowing or suffocating! 1. Cordless screwdriver 2. Battery charger 3. Bits x 4pcs (50 mm, SL5,SL6,PH1,PH2) 4. User s manual 3. Proper use The cordless screwdriver is designed for tightening and undoing screws. The machine is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user /operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this. 4. Technical data Model PT-0721A PT-0721F Plug type Rated Voltage No-load Speed Torque Setting Output torque Drive (Collet) Battery Charging Time Free running time Size Weight 7.2VDC two gear speed: 0~200rpm / 0~400rpm 15+1 Position MAX. 5 N.M (51 Kgf-cm / 44.26 lbf-in) 1/4 quick release chuck Li-ion 7.2V 1300mAh 3-5 hours >70min. (unload speed) 160*180*50mm 0.5kg Adaptor (Charger) Model no. 5PT-0721-ADA 5PT-0721-ADF Specification Indoor operation only Input 120V AC 60Hz Output 9V DC 300mA Input 230V AC 50Hz Output 9V DC 300mA Keep the noise emissions and vibrations to a minimum. Only use appliances which are in perfect working order. Service and clean the appliance regularly. Adapt your working style to suit the appliance. Do not overload the appliance. 3

Residual risks Even if you use this electric power tool in accordance with instructions, certain residual risks cannot be rules out. The following hazards may arise in connection with the equipment s construction and layout: 1. Lung damage if no suitable protective dust mask is used. 2. Damage to hearing if no suitable ear protection is used. 3. Health damage caused by hand-arm vibrations if the equipment is used over a prolonged period or is not properly guided and maintained. 5. Before starting the equipment Be sure to read the following information before you use your cordless screwdriver for the first time: 1. Charge the battery pack with the charger supplied. 2. Only ever use screwdriver bits which are suitable for the purpose and in faultless condition. 3. Always check for concealed electric cables and gas and water pipes when drilling and screwing in walls. 6. Operation 6.1 Charging the battery The battery is protected from exhaustive discharge. An integrated protective circuit automatically switches off the equipment when the battery is flat. In this case the bit chuck will cease to turn. Warning! Do not press the ON/OFF switch any more if the protective circuit has actuated. This may damage the battery. Important! The handle may become a little warm during the charging process. This is normal. If the battery pack fails to charge, please check whether there is voltage at the socket-outlet and check for proper contact with the charging contacts in the battery charger If the battery still fails to charge, send the battery charger and the screwdriver to our customer services department. Timely recharging of the battery pack will help it serve you well for a long time. You must recharge the battery pack when you notice that the power of the screwdriver drops. 6.2 Clockwise/Counter-clockwise selector switch The slide switch above the ON/OFF switch is for setting the direction of rotation of the cordless screwdriver and for preventing the cordless screwdriver from being switched on inadvertently. You can select between clockwise and counter- clockwise rotation. Change the direction of rotation only when the equipment is at a standstill. If you fail to observe this point, the gearing may become damaged. When the slide switch is in the middle position, the ON/OFF switch is blocked. 4

6.3 Operating Trigger Press the operating trigger to switch on the cordless screwdriver on. Release the operating trigger to switch off the tool. 6.4 LED light The LED light can be used in poor lighting conditions to illuminate the area where you want to screw. When pressing the trigger, the LED lights on automatically, and off when the trigger released 6.5 Battery capacity indicator Press the button for the battery capacity indicator. The battery capacity indicator will indicates the battery power status on 3 colored LEDs. All LEDs illuminate: The battery is fully charged The yellow and red LED illuminate: The battery has an adequate remaining charge Red LED: The battery is empty, recharge the battery 6.6 Changing Important! Press the clockwise/counter-clockwise selector switch to centre position whenever you changing the bits or doing maintenance work on the cordless screwdriver. When changing the bits pull back and hold the locking sleeve. Insert the bit into the bit chuck and let go of the locking sleeve. Check that it is secure by attempting to pull the tool apart again. 6.7 Screw driving We recommend using self-centering screws (e.g. Torx screws, recessed head screws) designed for reliable working. Be sure to use a bit that matches the screw in shape and size. Set the torque, as described elsewhere in these operating instructions, to suit the size of screw. 7. Cleaning, maintenance and ordering of spare parts Always pull out the mains power plug before starting any cleaning work. 7.1 Cleaning Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure. We recommend that you clean the device immediately each time you have finished using it. Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device 5

7.2 Maintenance There are no parts inside the equipment which require additional maintenance. 7.3 Ordering replacement parts Please quote the following data when ordering replacement parts: Type of machine Article number of the machine Identification number of the machine Replacement part number of the part required For our latest prices and information please go to www.prokits.com.tw 8. Disposal and recycling The unit is supplied in packaging to prevent its being damaged in transit. This packaging is raw material and can therefore be reused or can be returned to the raw material system. The unit and its accessories are made of various types of material, such as metal and plastic. Defective components must be disposed of as special waste. Ask your dealer or your local council. 9. Storage Store the equipment and accessories out of children s reach in a dark and dry place at above freezing temperature. The ideal storage temperature is between 5 and 30 C. Store the electric tool in its original packaging. 6

PT-0721 7.2V 鋰電池充電起子重要! 使用設備時, 必須遵守安全防範措施, 以避免人員傷亡和損害請閱讀完整的操作手冊, 並適當存放請將本手冊存放在一個安全的地方, 從而使資訊是隨時可用如果你將設備給任何其他人, 請給他們這些操作說明不遵守這些指令和安全資訊將導致產品損壞或意外產生 1. 安全資訊請參閱說明書警告! 閱讀所有安全法規和指令. 任何錯誤可能會導致觸電, 火災和 / 或嚴重傷害, 將說明書放置于安全的地方以利使用 2. 產品部件說明和配件 2.1 產品部件說明 1. 夾頭 2. 鎖緊套筒 3. 15+1 段扭力選擇環 4. 二段轉速控制健 5. 電池容量指示燈 6. 電池容量指示燈開關 7. 順時針 / 逆時針選擇鍵 8. 充電插頭 9. 啟動開關壓鈕 10. LED 燈 2.2 配件提供打開包裝, 小心取出設備拆掉包裝材料或任何運輸防護材料檢查是否所有的配件都有提供. 如果可能的話, 請保持包裝到質保期結束為止 1. 電動螺絲起子, 2. 電池充電器 3. 4 支起子頭 (50 mm, SL5,SL6,PH1,PH2) 4. 操作使用說明書安全說明重要設備和包裝材料不是玩具切勿讓孩子玩塑膠袋, 或小零件, 否則有吞咽或窒息的危險! 3. 正確使用無電源線的電動起子是為螺絲鎖緊和放鬆用的設計, 電動起子只用於其既定的目的任何其他用途, 被認為是使用不當的情況. 用戶 / 操作員將為造成任何損害或傷害承擔責任, 而非製造商 7

4. 技術資料項目 PT-0721A PT-0721F 插頭型式額定電壓無負載轉速扭力設定輸出扭力值起子夾頭充電電池 7.2VDC 雙齒輪 : 0~200rpm / 0~400rpm 15+1 組設定 MAX. 5 N.M (51 Kgf-cm / 44.26 lbf-in) 1/4 快拆接頭鋰電 7.2V 1300mAh 充電時間無載使用時間尺寸重量充電器 3-5 hours 70 分鐘 160*180*50mm 0.5kg 型號 5PT-0721-ADA 5PT-0721-ADF 規格請於戶內使用 Input 120V AC 60Hz Output 9V DC 300mA Input 230V AC 50Hz Output 9V DC 300mA 保持雜訊的排放量和振動到最低限度使用器具于正常的工作條件定期清潔器具, 使之適應你的工作要求, 善用設備, 不要超負荷使用設備剩餘風險即使您使用這個電動工具時按照指示操作, 某些不確定的風險可能不能排除可能產生以下危害 1. 如果沒有合適的防護防塵口罩使用, 可能損害肺部 2. 如果沒有合適的護耳產品, 可能損害聽力 3. 如果該設備使用時間過長或沒有正確引導和維護, 手臂遭受振動可能損害健康, 5. 在啟動設備之前在首次使用前您的充電電批, 請務必閱讀以下的資訊 1. 使用充電器將電池充滿電 2. 測試過, 才能找到合適的扭力 3. 鑽孔或在牆壁鎖螺絲時請務必檢查隱蔽在牆內的電纜和煤氣管道, 水管等 8

6. 操作 6.1 電池充電電池有過充保護, 內部有自動保護電路, 警告! 不要一直不斷的重覆按 ON / OFF 開關引起保護電路啟動這可能損壞電池檢查您的電源電壓是否與銘牌上標明的一樣. 充電過程中充電電纜連接到充電適配器重要! 充電過程中手柄可能有點發熱, 這是正常的如果電池無法充電, 請檢查 : 插座是否有電壓, 是否有接觸到, 如果電池仍然無法充電, 請將電池充電器和電批發送到我們的客戶服務部門及時給電池充電, 將有利於延長電池使用壽命當您發現電批扭力下降時, 您應馬上充電 6.2 順時針 / 逆時針選擇鍵按壓滑動此鍵可以選擇轉向, 您可以選擇順時針方向和反順時針方向旋轉只有當設備處於停止狀態時, 才可以改變旋轉方向如果你不注意這一點, 齒輪可能會損壞當滑動開關在中間位置時, 轉軸是被鎖住不能轉動的 6.3 啟動開關壓下開關啟動電批, 釋放開關停止電批運轉 6.4 LED 燈 LED 燈便於在光線不好的地方使用電批. 壓下啟動開關就會開啟 LED 燈, 釋放則 LED 燈熄滅 6.5 電池容量指示燈按下電池容量指示燈開關, 電池容量指示燈顯示 3 個彩色 LED 電池的充電狀態..所有 LED 點亮 : 電池完全充電黃色和紅色的 LED 點亮 : 電池有足夠的剩餘電量紅色 LED: 電池沒電, 需對電池充電 6.6 更換批頭及維護重要! 每當你進行更換批頭及維護產品的工作時請先將轉向選擇鍵按壓滑動之中間位置以鎖定轉軸更換批頭請將鎖緊套筒往後拉, 將批頭插入夾頭孔內, 鬆開鎖套再次檢查它是安全固定的, 再使用電批 6.7 螺絲請務必使用匹配形狀和大小的螺絲釘, 并設置好扭矩我們建議採用自攻螺絲 ( 如 Torx 螺釘, 凹頭螺釘 ) 無論在何種場合, 請注意以上事宜 9

7. 清洗, 保養和配件訂購在進行任何清潔工作開始之前, 務必拔出電源插頭 7.1 清潔保持部件的清潔, 盡量遠離塵土和灰塵, 使用濕布或低壓氣泵擦拭吹淨每次使用完電批, 我們建議您立即清潔設備. 定期用濕布加一些肥皂水清潔設備, 請勿使用清潔劑或溶劑, 這可能會損壞設備的塑膠部件確保沒有水可以滲入設備 7.2 維護設備內其他部件無須維修保養 7.3 訂購更換零件訂購更換零件時, 請注明下列數據 : 1. 機器型號 2. 機器的數量 3. 機器的系列號對於我們的最新價格和資訊, 請訪問 www.prokits.com.tw 8. 處置和回收利用外包裝是防止其在運輸途中受損這種包裝原料, 可以被重複利用各類材料, 如金屬和塑膠, 配件有缺陷的部件必須作為特殊廢物處置, 請詢問您的經銷商或當地政府 9. 存儲將設備和配件存放在兒童不能接觸的地方理想的存儲溫度是 5-30, 請以原包裝存儲 10