1 Important instructions for safety and environment This section contains safety instructions that will help protect from risk of personal injury or p

Transcription

1 PW4810 Washing Machine User s Manual Document Number _EN/ (11:15)

2 1 Important instructions for safety and environment This section contains safety instructions that will help protect from risk of personal injury or property damage. Failure to follow these instructions shall void any warranty. 1.1 General safety This product can be used by children at and above 8 years old and by persons whose physical, sensory or mental capabilities were not fully developed or who lack experience and knowledge provided that they are supervised or trained on the safe usage of the product and the risks it brings out. hildren must not play with the product. leaning and maintenance works should not be performed by children unless they are supervised by someone. Never place the product on a carpet-covered floor. Otherwise, lack of airflow beneath the machine will cause electrical parts to overheat. This will cause problems with your product. If the product has a failure, it should not be operated unless it is repaired by the uthorized Service gent. There is the risk of electric shock! This product is designed to resume operating in the event of powering on after a power interruption. If you wish to cancel the programme, see "ancelling the programme" section. onnect the product to a grounded outlet protected by a 16 fuse. Do not neglect to have the grounding installation made by a qualified electrician. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations. The water supply and draining hoses must be securely fastened and remain undamaged. Otherwise, there is the risk of water leakage. Never open the loading door or remove the filter while there is still water in the drum. Otherwise, risk of flooding and injury from hot water will occur. Do not force open the locked loading door. The loading door will be ready to open just a few minutes after the washing cycle comes to an end. In case of forcing the loading door to open, the door and the lock mechanism may get damaged. Unplug the product when not in use. Never wash the product by spreading or pouring water onto it! There is the risk of electric shock! Never touch the plug with wet hands! Never unplug by pulling on the cable, always pull out by grabbing the plug. Use detergents, softeners and supplements suitable for automatic washing machines only. Follow the instructions on the textile tags and on the detergent package. The product must be unplugged during installation, maintenance, cleaning and repairing procedures. lways have the installation and repairing procedures carried out by the uthorized Service gent. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons. If the power cable is damaged, it must be replaced by the manufacturer, after sales service or a similarly qualified person (preferably an electrician) or someone designated by the importer in order to avoid possible risks. 2 / EN Washing Machine / User s Manual

3 Place the product on a rigid, flat and level surface. Do not place it on a long-pile rug or similar surfaces. Do not place the product on a high platform or near the edge on a cascaded surface. Do not place the product on the power cable. Never use sponge or scrub materials. These will damage the painted, chrome plated and plastic surfaces. 1.2 Intended use This product has been designed for domestic use. It is not suitable for commercial use and it must not be used out of its intended use. The product must only be used for washing and rinsing of laundry that are marked accordingly. The manufacturer waives any responsibility arisen from incorrect usage or transportation. 1.3 hildren's safety Packaging materials are dangerous to children. Keep packaging materials in a safe place away from reach of the children. Electrical products are dangerous for the children. Keep children away from the product when it is in use. Do not let them to tamper with the product. Use child lock to prevent children from intervening with the product. Do not forget to close the loading door when leaving the room where the product is located. Store all detergents and additives in a safe place away from the reach of the children by closing the cover of the detergent container or sealing the detergent package. While washing the laundry at high temperatures, the loading door glass becomes hot. Therefore, keep especially the children away from the loading door of the machine while the washing operation is in progress. 1.4 Package information Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities. 1.5 Disposing of the waste product This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Therefore, do not dispose the product with normal domestic waste at the end of its service life. Take it to a collection point for the recycling of electrical and electronic equipment. Please consult your local authorities to learn the nearest collection point. Help protect the environment and natural resources by recycling used products. For children's safety, cut the power cable and break the locking mechanism of the loading door so that it will be non-functional before disposing of the product. 3 / EN Washing Machine / User s Manual

4 1.6 ompliance with WEEE Directive This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE). This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Do not dispose of the waste product with normal domestic and other wastes at the end of its service life. Take it to the collection center for the recycling of electrical and electronic equipment. Please consult your local authorities to learn about these collection centers. ompliance with RoHS Directive: The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive. 4 / EN Washing Machine / User s Manual

5 2 Installation Refer to the nearest uthorised Service gent for installation of the product. To make the product ready for use, review the information in the user manual and make sure that the electricity, tap water supply and water drainage systems are appropriate before calling the uthorized Service gent. If they are not, call a qualified technician and plumber to have any necessary arrangements carried out. Preparation B warning: warning: of the location and electrical, tap water and waste water installations at the place of installation is under customer's responsibility. Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or crushed while pushing the product into its place after installation or cleaning procedures. Installation and electrical connections of the product must be carried out by the uthorized Service gent. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons. Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products cause risks for your safety. 2.1 ppropriate installation location Place the machine on a rigid floor. Do not place it on a long pile rug or similar surfaces. Total weight of the washing machine and the dryer -with full load- when they are placed on top of each other reaches to approx. 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying capacity! Do not place the product on the power cable. Do not install the product at places where temperature may fall below 0º. Place the product at least 1 cm away from the edges of other furniture. 2.2 Removing packaging reinforcement Tilt the machine backwards to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon. 2. Remove transportation safety bolts by turning them gently. 3. ttach the plastic covers supplied in the User Manual bag into the holes on the rear panel. (P) Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future. Never move the product without the transportation safety bolts properly fixed in place! 2.4 onnecting water supply The water supply pressure required to run the product is between 1 to 10 bars (0.1 1 MPa). It is necessary to have liters of water flowing from the fully open tap in one minute to have your machine run smoothly. ttach a pressure reducing valve if water pressure is higher. If you are going to use the double water-inlet product as a single (cold) water-inlet unit, you must install the supplied stopper to the hot water valve before operating the product. (pplies for the products supplied with a blind stopper group.) warning: Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will get damaged or the product will switch to protection mode and will not operate. warning: Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry. 1. onnect the special hoses supplied with the product to the water inlets on the product. Red hose (left) (max. 90 º) is for hot water inlet, blue hose (right) (max. 25 º) is for cold water inlet. 2.3 Removing the transportation locks warning: Do not remove the transportation locks before taking out the packaging reinforcement. warning: Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be damaged. 1. Loosen all the bolts with a suitable spanner until they rotate freely (). warning: Ensure that the cold and hot water connections are made correctly when installing the product. Otherwise, your laundry will come out hot at the end of the washing process and wear out. 2. Tighten all hose nuts by hand. Never use a tool when tightening the nuts. 3. Open the taps completely after making the hose connection to check for water leaks at the connection 5 / EN Washing Machine / User s Manual

6 points. If any leaks occur, turn off the tap and remove the nut. Retighten the nut carefully after checking the seal. To prevent water leakages and damages caused by them, keep the taps closed when the machine is not in use. 2.5 onnecting to the drain The end of the drain hose must be directly connected to the wastewater drain or to the washbasin. warning: Your house will be flooded if the hose comes out of its housing during water discharge. Moreover, there is risk of scalding due to high washing temperatures! To prevent such situations and to ensure smooth water intake and discharge of the machine, fix the end of the discharge hose tightly so that it cannot come out. The hose should be attached to a height of at least 40 cm, and 100 cm at most. In case the hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out excessively wet. Therefore, follow the heights described in the figure. 100cm To prevent flowing of dirty water back into the machine and to allow for easy discharge, do not immerse the hose end into the dirty water or do not drive it in the drain more than 15 cm. If it is too long, cut it short. The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched between the drain and the machine. If the length of the hose is too short, use it by adding an original extension hose. Length of the hose may not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak. 2.6 djusting the feet warning: In order to ensure that the product operates more silently and vibration-free, it must stand level and balanced on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from its place and cause crushing and vibration problems. 1. Loosen the lock nuts on the feet by hand. 2. djust the feet until the product stands level and balanced. 3. Tighten all lock nuts again by hand. 40cm warning: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged. 2.7 Electrical connection onnect the product to a grounded outlet protected by a 16 fuse. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations. onnection must comply with national regulations. Power cable plug must be within easy reach after installation. If the current value of the fuse or breaker in the house is less than 16 mps, have a qualified electrician install a 16 mp fuse. The voltage specified in the "Technical specifications" section must be equal to your mains voltage. Do not make connections via extension cables or multiplugs. B warning: Damaged power cables must be replaced by the uthorized Service gents. Transportation of the product 1. Unplug the product before transporting it. 2. Remove water drain and water supply connections. 3. Drain all water that has remained in the product. (SEE 5.5) 4. Install transportation safety bolts in the reverse order of removal procedure; (SEE 2.3) Never warning: move the product without the transportation safety bolts properly fixed in place! Packaging materials are dangerous to children. Keep packaging materials in a safe place away from reach of the children. 6 / EN Washing Machine / User s Manual

7 3 Preparation 3.1 Sorting the laundry Sort laundry according to type of fabric, colour, and degree of soiling and allowable water temperature. lways obey the instructions given on the garment tags. 3.2 Preparing laundry for washing Laundry items with metal attachments such as, underwired bras, belt buckles or metal buttons will damage the machine. Remove the metal pieces or wash the clothes by putting them in a laundry bag or pillow case. Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside out and brush. Such objects may damage the product or cause noise problem. Put small size clothes such as infant's socks and nylon stockings in a laundry bag or pillow case. Place curtains in without compressing them. Remove curtain attachment items. Fasten zippers, sew loose buttons and mend rips and tears. Wash machine washable or hand washable labeled products only with an appropriate programme. Do not wash colours and whites together. New, dark coloured cottons release a lot of dye. Wash them separately. Tough stains must be treated properly before washing. If unsure, check with a dry cleaner. Use only dyes/colour changers and limescale removers suitable for machine wash. lways follow the instructions on the package. Wash trousers and delicate laundry turned inside out. Keep laundry items made of ngora wool in the freezer for a few hours before washing. This will reduce pilling. Laundry that are subjected to materials such as flour, lime dust, milk powder, etc. intensely must be shaken off before placing into the machine. Such dusts and powders on the laundry may build up on the inner parts of the machine in time and can cause damage. 3.3 Things to be done for energy saving Following information will help you use the product in an ecological and energy-efficient manner. Operate the product in the highest capacity allowed by the programme you have selected, but do not overload; see, "Programme and consumption table". lways follow the instructions on the detergent packaging. Wash slightly soiled laundry at low temperatures. Use faster programmes for small quantities of lightly soiled laundry. Do not use prewash and high temperatures for laundry that is not heavily soiled or stained. If you plan to dry your laundry in a dryer, select the highest spin speed recommended during washing process. Do not use detergent in excess of the amount recommended on the detergent package. 3.4 Initial use Before starting to use the product, make sure that all preparations are made in accordance with the instructions in sections Important safety instructions and Installation. To prepare the product for washing laundry, perform first operation in Drum leaning programme. If your product is not equipped with Drum leaning programme, perform the Initial Use procedure in accordance with the methods described under 5.2 leaning the loading door and the drum section of the user manual. Use an anti-limescale suitable for the washing machines. Some water might have remained in the product due to the quality control processes in the production. It is not harmful for the product. 3.5 orrect load capacity The maximum load capacity depends on the type of laundry, the degree of soiling and the washing programme desired. The machine automatically adjusts the amount of water according to the weight of the loaded laundry. warning: Follow the information in the Programme and consumption table. When overloaded, machine's washing performance will drop. Moreover, noise and vibration problems may occur. 3.6 Loading the laundry 1. Open the loading door. 2. Place laundry items loosely into the machine. 3. Push the loading door to close until you hear a locking sound. Ensure that no items are caught in the door. The warning: loading door is locked while a programme is running. The door can only be opened a while after the programme comes to an end. In case of misplacing the laundry, noise and vibration problems may occur in the machine. 3.7 Using detergent and softener When using detergent, softener, starch, fabric dye, bleach or limescale remover read the manufacturer's instructions on the package carefully and follow the suggested dosage values. Use measuring cup if available. Detergent Drawer The detergent drawer is composed of three compartments: (1) for prewash (2) for main wash (3) for softener (*) in addition, there is siphon piece in the softener compartment / EN Washing Machine / User s Manual

8 Detergent, softener and other cleaning agents dd detergent and softener before starting the washing programme. Never leave the detergent drawer open while the washing programme is running! When using a programme without prewash, do not put any detergent into the prewash compartment (compartment nr. "1"). In a programme with prewash, do not put liquid detergent into the prewash compartment (compartment nr. "1"). Do not select a programme with prewash if you are using a detergent bag or dispensing ball. Place the detergent bag or the dispensing ball directly among the laundry in the machine. If you are using liquid detergent, do not forget to place the liquid detergent cup into the main wash compartment (compartment nr. "2"). hoosing the detergent type The type of detergent to be used depends on the type and colour of the fabric. Use different detergents for coloured and white laundry. Wash your delicate clothes only with special detergents (liquid detergent, wool shampoo, etc.) used solely for delicate clothes. When washing dark coloured clothes and quilts, it is recommended to use liquid detergent. Wash woolens with special detergent made specifically for woolens. warning: warning: Do not use soap powder. Use only detergents manufactured specifically for washing machines. djusting detergent amount The amount of washing detergent to be used depends on the amount of laundry, the degree of soiling and water hardness. Do not use amounts exceeding the dosage quantities recommended on the detergent package to avoid problems of excessive foam, poor rinsing, financial savings and finally, environmental protection. Use lesser detergent for small amounts or lightly soiled clothes. Using softeners Pour the softener into the softener compartment of the detergent drawer. Do not exceed the (>max<) level marking in the softener compartment. If the softener has lost its fluidity, dilute it with water before putting it in the detergent drawer. Using liquid detergents If the product contains a liquid detergent cup: Make sure that you have placed the liquid detergent cup in compartment nr. "2". If the liquid detergent has lost its fluidity, dilute it with water before putting in the detergent cup. Soiling Level Soiling Level Soiling Level Heavily Soiled (difficult stains such as grass, coffee, fruits and blood.) Normally Soiled (For example, stains caused by body on collars and cuffs) Lightly Soiled (No visible stains exist.) lothes Light colours and whites (Recommended temperature range based on soiling level: ) It may be necessary to pre-treat the stains or perform prewash. Powder and liquid detergents recommended for whites can be used at dosages recommended for heavily soiled clothes. It is recommended to use powder detergents to clean clay and soil stains and the stains that are sensitive to bleaches. Powder and liquid detergents recommended for whites can be used at dosages recommended for normally soiled clothes. Powder and liquid detergents recommended for whites can be used at dosages recommended for lightly soiled clothes. olours (Recommended temperature range based on soiling level: cold -40 ) Powder and liquid detergents recommended for colours can be used at dosages recommended for heavily soiled clothes. It is Heavily Soiled recommended to use powder detergents to clean clay and soil stains and the stains that are sensitive to bleaches. Use detergents without bleach. Powder and liquid detergents recommended Normally Soiled for colours can be used at dosages recommended for normally soiled clothes. Use detergents without bleach. Powder and liquid detergents recommended Lightly Soiled for colours can be used at dosages recommended for lightly soiled clothes. Use detergents without bleach. Dark colours (Recommended temperature range based on soiling level: cold -40 ) Liquid detergents suitable for colours Heavily Soiled and dark colours can be used at dosages recommended for heavily soiled clothes. Liquid detergents suitable for colours Normally Soiled and dark colours can be used at dosages recommended for normally soiled clothes. Liquid detergents suitable for colours Lightly Soiled and dark colours can be used at dosages recommended for lightly soiled clothes. 8 / EN Washing Machine / User s Manual

9 Soiling Level lothes Delicates/Woollens/Silks (Recommended temperature range based on soiling level: cold -30 ) Prefer liquid detergents produced for Heavily Soiled delicate clothes. Woollen and silk clothes must be washed with special woollen detergents. Prefer liquid detergents produced for Normally Soiled delicate clothes. Woollen and silk clothes must be washed with special woollen detergents. Prefer liquid detergents produced for Lightly Soiled delicate clothes. Woollen and silk clothes must be washed with special woollen detergents. Use just a little amount (approx. 50 ml) of bleaching agent and rinse the clothes very well as it causes skin irritation. Do not pour the bleaching agent onto the clothes and do not use it for coloured clothes. When using oxygen based bleaches, select a programme that washes at a lower temperature. Oxygen based bleaches can be used together with detergents; however, if its thickness is not the same with the detergent, put the detergent first into the compartment nr. "2" in the detergent drawer and wait until the detergent flows while the machine is taking in water. dd the bleaching agent from the same compartment while the machine is still taking in water. Using limescale remover When required, use limescale removers manufactured specifically for washing machines only. If the product does not contain a liquid detergent cup: Do not use liquid detergent for the prewash in a programme with prewash. Liquid detergent stains your clothes when used with Delayed Start function. If you are going to use the Delayed Start function, do not use liquid detergent. Using gel and tablet detergent pply the following instructions when using tablet, gel and similar detergents. If the gel detergent thickness is fluidal and your machine does not contain a special liquid detergent cup, put the gel detergent into the main wash detergent compartment during first water intake. If your machine contains a liquid detergent cup, fill the detergent into this cup before starting the programme. If the gel detergent thickness is not fluidal or in the shape of capsule liquid tablet, put it directly into the drum before washing. Put tablet detergents into the main wash compartment (compartment nr. "2") or directly into the drum before washing. Tablet detergents may leave residues in the detergent compartment. If you encounter such a case, place the tablet detergent between the laundry, close to the lower part of the drum in future washings. Use the tablet or gel detergent without selecting the prewash function. Using starch dd liquid starch, powder starch or the fabric dye into the softener compartment. Do not use softener and starch together in a washing cycle. Wipe the inside of the machine with a damp and clean cloth after using starch. Using bleaches Select a programme with prewash and add the bleaching agent at the beginning of the prewash. Do not put detergent in the prewash compartment. s an alternative application, select a programme with extra rinse and add the bleaching agent while the machine is taking water from the detergent compartment during first rinsing step. Do not use bleaching agent and detergent by mixing them. 9 / EN Washing Machine / User s Manual

10 4 Operating the product 4.1 ontrol panel Spin Speed djustment button 2 - Display 3 - Temperature djustment button 4 - Programme Selection knob 4.2 Display symbols F1 F2 F3 F4 a - Spin Speed indicator b - Temperature indicator c - Spin symbol d - Temperature symbol e - Remaining Time and Delayed Start indicator f - Programme Indicator symbols (Prewash / Main Wash / Rinse / Softener / Spin) g - Economy symbol h - Delayed Start symbol i - Door Locked symbol j - Start symbol k - Pause symbol l - uxiliary Function symbols m - No Water symbol 5 - On / Off button 6 - Delayed Start buttons (+ / -) 7 - uxiliary Function buttons 8 - Start / Pause / ancel button 4.3 Preparing the machine Make sure that the hoses are connected tightly. Plug in your machine. Turn the tap on completely. Place the laundry in the machine. dd detergent and fabric softener. 4.4 Programme selection Select the programme suitable for the type, quantity and soiling degree of the laundry in accordance with the "Programme and consumption table" and the temperature table below old Heavily soiled white cottons and linens. (coffee table covers, tableclothes, towels, bed sheets, etc.) Normally soiled, coloured, fade proof linens, cottons or synthetic clothes (shirt, nightgown, pajamas, etc.) and lightly soiled white linens (underwear, etc.) Blended laundry including delicate textile (veil curtains, etc.), synthetics and woolens. Select the desired programme with the Programme Selection button. Programmes are limited with the highest spin speed appropriate for that particular type of fabric. When selecting a programme, always consider the type of fabric, colour, degree of soiling and permissible water temperature. lways select the lowest required temperature. Higher temperature means higher power consumption. For further programme details, see "Programme and consumption table" 10 / EN Washing Machine / User s Manual

11 4.5 Main programmes Depending on the type of fabric, use the following main programmes. otton Use this programme for your cotton laundry (such as bed sheets, duvet and pillowcase sets, towels, bathrobes, underwear, etc.). Your laundry will be washed with vigorous washing action for a longer washing cycle. Synthetics Use this programme to wash your synthetic clothes (shirts, blouses, synthetic/cotton blends, etc.). It washes with a gentle action and has a shorter washing cycle compared to the ottons programme. For curtains and tulle, use the Synthetic 40 programme with prewash and anti-creasing functions selected. s their meshed texture causes excessive foaming, wash the veils/ tulle by putting little amount of detergent into the main wash compartment. Do not put detergent in the prewash compartment. Wool Use this programme to wash your woolen clothes. Select the appropriate temperature complying with the tags of your clothes. Use appropriate detergents for woolens. 4.6 dditional programmes For special cases, additional programmes are available in the machine. dditional programmes may differ according to the model of the machine. otton Eco You may wash your normally soiled durable cotton and linen laundry in this programme with the highest energy and water saving compared to all other wash programmes suitable for cottons. ctual water temperature may differ from the declared cycle temperature. Programme duration may automatically be shortened during later stages of the programme if you wash less amount (e.g. ½ capacity or less) of laundry. In this case energy and water consumption will be further decreased giving you the opportunity for a more economical wash. This feature is available for certain models having remaining time display. Baby lothes Use this programme for your laundry for which you require an anti-allergic and hygienic washing at high temperature with intensive and long washing cycles. Babyprotect+ 60 programme is tested and approved by The British llergy Foundation (llergy UK) in United Kingdom. Delicate Use this programme to wash your delicate clothes. It washes with a gentle action without any interim spin compared to the Synthetics programme. Hand Wash Use this programme to wash your woolen/delicate clothes that bear not machine- washable tags and for which hand wash is recommended. It washes laundry with a very gentle washing action to not to damage clothes. Quick Use this programme to wash your lightly soiled cotton clothes in a short time. Eco 40 0 Use this programme to wash your laundry for which you cannot use ottons 60 programme. It gives the same result with the ottons 60 programme by washing for a longer time at 40, thus enabling energy saving. Mix 40 0 Use this programme to wash your cotton and synthetic clothes together without sorting them. Intensive You can wash your durable and heavily soiled clothes on this program. This program washes for a longer time and an extra rinse cycle will be made compared to the ottons program. You can use it for your heavily soiled clothes that you wish to be rinsed gently. Shirt Use this programme to wash the shirts made of cotton, synthetic and synthetic blended fabrics together. urtain Use this programme to wash your tulles and curtains. Thanks to the special spin profile of the programme, tulles and curtains crease lesser. s their meshed texture causes excessive foaming, wash the veils/tulle by putting little amount of detergent into the main wash compartment. Do not put detergent in the prewash compartment. otton20 0 Use this programme, which is much more sensitive to environment and natural resources, to wash your lightly soiled and unstained cotton laundry (max. 3.5 kg) in a short time and economically. 11 / EN Washing Machine / User s Manual

12 4.7 Special programmes For specific applications, select any of the following programmes. Rinse Use this programme when you want to rinse or starch separately. Spin+Drain Use this programme to apply an additional spin cycle for your laundry or to drain the water in the machine. Before selecting this programme, select the desired spin speed and press Start / Pause / ancel button. The machine will spin the laundry with the set spin speed and drain the water coming out of them. If you wish to drain only the water without spinning your laundry, select the Pump+Spin programme and then select the No Spin function with the help of Spin Speed djustment button. Press Start / Pause / ancel button. Use a lower spin speed for delicate laundries. 4.8 Temperature selection Whenever a new programme is selected, the maximum temperature for the selected programme appears on the temperature indicator. To decrease the temperature, press the Temperature djustment button. Temperature decreases with increments of 10 and finally, - symbol indicating the cold wash option appears on the display. If you scroll to cold wash option and press Temperature djustment button again, the recommended temperature for the selected programme appears on the display. Press the Temperature djustment button again to decrease the temperature. 4.9 Spin speed selection Whenever a new programme is selected, the recommended spin speed of the selected programme is displayed on the spin speed indicator. To decrease the spin speed, press the Spin Speed djustment button. Spin speed decreases gradually. Then, depending on the model of the product, "Rinse Hold" and "No Spin" options appear on the display. See "uxiliary function selection" section for explanations of these options. Rinse Hold option is indicated with symbol and No Spin option is indicated with symbol. 12 / EN Washing Machine / User s Manual

13 4.10 Programme and consumption table EN 2 uxiliary functions Programme ( ) Max. Load (kg) Water onsumption (l) Energy onsumption (kwh) Max. Speed*** Pre-wash Quick Rinse + nti- creasing Rinse Hold Selectable temperature range otton old otton old otton old Baby lothes * otton Eco 60** old otton Eco old Intensive * Synthetics old Synthetics old 0 Mix old Quick old Quick old Quick old otton Wool old Hand Wash old urtain * * * 40-old Shirt * 60-old Eco Delicate old : Selectable * : utomatically selected, no cancelling. ** : Energy Label programme (EN Ed.3) *** If maximum spin speed of the machine is lower then this value, you can only select up to the maximum spin speed. - : See the programme description for maximum load. 13 / EN Washing Machine / User s Manual

14 The Water You ** otton eco 40 and otton eco 60 are standard cycles. These cycles are known as 40 cotton standard cycle and 60 cotton standard cycle and indicated with the symbols on the panel. auxiliary functions in the table may vary according to the model of your machine. and power consumption may vary subject to the changes in water pressure, water hardness and temperature, ambient temperature, type and amount of laundry, selection of auxiliary functions and spin speed, and changes in electric voltage. can see the washing time of the programme you have selected on the display of the machine. It is normal that small differences may occur between the time shown on the display and the real washing time. Indicative values for Synthetics programmes (EN) Load (kg) Water onsumption (l) Energy onsumption (kwh) Programme Duration (min) * Remaining Moisture ontent (%) ** 1000 rpm Remaining Moisture ontent (%) ** > 1000 rpm Synthetics : Synthetics : * You can see the washing time of the programme you have selected on the display of the machine. It is normal that small differences may occur between the time shown on the display and the real washing time. ** Remaining moisture content values may differ according to the selected spin speed. 14 / EN Washing Machine / User s Manual

15 4.11 uxiliary function selection Select the desired auxiliary functions before starting the programme. Furthermore, you may also select or cancel auxiliary functions that are suitable to the running programme by pressing the Start / Pause / ancel button when the machine is operating. For this, the machine must be in a step before the auxiliary function you are going to select or cancel. Depending on the programme, press a, b, c or d buttons to select the desired auxiliary function. Symbol of the selected auxiliary function appears on the display. Some functions cannot be selected together. If a second auxiliary function conflicting with the first one is selected before starting the machine, the function selected first will be canceled and the second auxiliary function selection will remain active. For example, if you want to select Quick Wash after you have selected the Prewash, Prewash will be canceled and Quick Wash will remain active. n auxiliary function that is not compatible with the programme cannot be selected. (See Programme and consumption table ) uxiliary Function buttons may vary according to the model of the machine. Pre-wash Prewash is only worthwhile for heavily soiled laundry. Not using the Prewash will save energy, water, detergent and time. F1 appears on the display when you select this function (a). Quick This function can be used in ottons and Synthetics programmes. It decreases the washing times and also the number of rinsing steps for lightly soiled laundry. F2 appears on the display when you select this function (b). When you select this function, load your machine with half of the maximum laundry specified in the programme table. Rinse+ This function enables the machine to make another rinsing in addition to the one already made after the main wash. Thus, the risk for sensitive skins (babies, allergic skins, etc.) to be effected by the minimal detergent remnants on the laundry can be reduced. F3 appears on the display when you select this function (c). nti- creasing This function creases the clothes lesser when they are being washed. Drum movement is reduced and spinning speed is limited to prevent creasing. In addition, washing is done with a higher water level. F4 appears on the display when you select this function (d) Time display Remaining time to complete the programme appears on the display while the programme is running. Tim is displayed as 01:30 in hours and minutes format. Programme time may differ from the values in the Programme and consumption table depending on the water pressure, water hardness and temperature, ambient temperature, amount and the type of laundry, auxiliary functions selected and the changes at the mains voltage. Delayed start With the Delayed Start function the startup of the programme may be delayed up to 24 hours. Delayed start time can be increased by increments of 30 minutes. Do not use liquid detergents when you set Delayed Start! There is the risk of staining of the clothes. Open the loading door, place the laundry and put detergent, etc. Select the washing programme, temperature, spin speed and, if required, the auxiliary functions. Set the desired delayed start time by pressing the Delayed Start + or - buttons. Delayed Start symbol flashes. Press Start / Pause / ancel button. Delayed start countdown starts. Delayed Start symbol illuminates steadily. Start symbol appears. : sign in the middle of the delayed start time on the display starts flashing. dditional laundry may be loaded during the delayed start period. t the end of the countdown, Delayed Start symbol disappears, washing cycle starts and the time of the selected programme appears on the display. hanging the delayed start period If you want to change the time during countdown: Press Start / Pause / ancel button. : sign in the middle of the delayed start time on the display stops flashing. Pause symbol appears. Delayed Start symbol flashes. Start symbol disappears. Set the desired delayed start time by pressing the Delayed Start + or - buttons. Press Start / Pause / ancel button. Delayed Start symbol illuminates steadily. Pause symbol disappears. Start symbol appears. : sign in the middle of the delayed start time on the display starts flashing. ancelling the Delayed Start function If you want to cancel the delayed start countdown and start the programme immediately: Press Start / Pause / ancel button. : sign in the middle of the delayed start time on the display stops flashing. Start symbol disappears. Pause symbol and Delayed Start symbol flashes. Decrease the delayed start time by pressing the Delayed Start - button. Programme duration appears after 30 minutes. Press Start / Pause / ancel button to start the programme Starting the programme Press Start / Pause / ancel button to start the programme. Start symbol showing the startup of the programme will turn on. Loading door is locked and Door Locked symbol appears on the display. The symbol of the step from which the programme has started appears on the display (Prewash, Main Wash, Rinse, Softener and Spin). 15 / EN Washing Machine / User s Manual

16 4.14 Progress of programme Progress of a running programme is indicated on the display with a set of symbols. Relevant symbol appears on the display at the beginning of each programme step and all symbols remain lit at the end of the programme. The farthermost right symbol indicates the current programme step. Prewash If the Prewash auxiliary function is selected, Prewash symbol appears on the display indicating that the prewash step has started. Main Wash Main Wash symbol indicating that the main wash step has started appears on the display. Rinse Rinse symbol indicating that the rinsing step has started appears on the display. Softener Softener symbol indicating that the softener step has started appears on the display. Spin ppears at the beginning of the final spin step and remains lit during Spin and Pump special programmes. If the machine does not pass to the spinning step, Rinse Hold function might be active or the automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the machine Loading door lock There is a locking system on the loading door of the machine that prevents opening of the door in cases when the water level is unsuitable. Door Locked symbol appears when the loading door is locked. This symbol will flash until the loading door becomes ready to open when programme completes or the machine is paused. Do not force to open the loading door in this step. Symbol disappears when the door is ready to open. You can open the door when the symbol disappears hanging the selections after programme has started Switching the machine to pause mode Press the Start / Pause / ancel button to switch the machine to pause mode. Pause symbol appears on the display indicating that the machine is paused. Start symbol disappears. hanging the speed and temperature settings for auxiliary functions Depending on the step the programme has reached, you may cancel or activate the auxiliary functions; see, "uxiliary function selection". You may also change the speed and temperature settings; see, "Spin speed selection" and "Temperature selection". dding or taking out laundry Press the Start / Pause / ancel button to switch the machine to pause mode. The programme follow-up light of the relevant step during which the machine was switched into the pause mode will flash. Wait until the Loading Door can be opened. Open the Loading Door and add or take out the laundry. lose the Loading Door. Make changes in auxiliary functions, temperature and speed settings if necessary. Press Start / Pause / ancel button to start the machine. The loading door will not open if the water temperature in the machine is high or the water level is above the door opening hild Lock Use hild Lock function to prevent children from tampering with the machine. Thus you can avoid any changes in a running programme. You can switch on and off the machine with On / Off button when the hild Lock is active. When you switch on the machine again, programme will resume from where it has stopped. To activate the hild Lock: Press and hold 2 nd and 4 th uxiliary Function buttons for 3 seconds. on appears on the display. Same phrase will appear on the display if you press any button when hild Lock is enabled. To deactivate the hild Lock: Press and hold 2 nd and 4 th uxiliary Function buttons for 3 seconds. OFF appears on the display. Do not forget to disable the child lock at the end of the programme if it was enabled before. Otherwise, machine will not allow to select a new programme ancelling the programme Press and hold Start / Pause / ancel button for 3 seconds. Start symbol flashes. Symbol of the step at which the programme was cancelled remains lit. "End" appears on the display and the programme is cancelled. If you want to open the loading door after you have cancelled the programme but it is not possible to open the loading door since the water level in the machine is above the loading door opening, then turn the Programme Selection knob to Pump+Spin programme and discharge the water in the machine Machine is in Rinse Hold mode Spin symbol flashes and Pause symbol illuminates when the machine is in Rinse Hold mode. If you want to spin your laundry when the machine is in this mode: djust the spin speed and press Start / Pause / ancel button. Pause symbol disappears and Start symbol appears. Programme resumes, discharges the water and spins the laundry. If you only want to drain the water without spinning: Just press Start / Pause / ancel button. Pause symbol disappears. Start symbol appears. Programme resumes and discharges the water only. 16 / EN Washing Machine / User s Manual

17 4.20 End of programme End appears on the display at the end of the programme. Symbols of the programme steps remain lit. uxiliary function, spin speed and temperature that were selected at the beginning of the programme remain selected Your machine is equipped with a Standby Mode In case of not starting any programme or waiting without making any other operation when the machine is turned on by On/Off button and while it is in selection step or if no other operation is performed approximately 2 minutes after the programme you selected has come to an end, your machine will automatically switch to energy saving mode. Brightness of indicator lights will decrease. lso, if your product is equipped with a display showing the programme duration, this display will completely turn off. In case of rotating the Programme Selection knob or pressing any button, lights and display will restore to their previous condition. Your selections made while exiting the energy saving mode may change. heck the appropriateness of your selections before starting the programme. Readjust if necessary. This is not a fault. 5 Maintenance and cleaning Service life of the product extends and frequently faced problems decrease if cleaned at regular intervals. 5.1 leaning the detergent drawer lean the detergent drawer at regular intervals (every 4-5 washing cycles) as shown below in order to prevent accumulation of powder detergent in time. If your detergent drawer is the one indicated in the following figure: Lift the rear part of the siphon to remove it as illustrated. fter performing the above mentioned cleaning procedures, replace the siphon back to its seating and push its front section downwards to make sure that the locking tab engages. 5.2 leaning the loading door and the drum Residues of softener, detergent and dirt may accumulate in your machine in time and may cause unpleasant odours and washing complaints. To avoid this, use the Drum leaning programme. If your machine is not featured with Drum leaning programme, use ottons-90 programme and select dditional Water or Extra Rinse auxiliary functions as well. Run the programme without any laundry in the machine. Before starting the programme, put max. 100 g of powder anti-limescale into the main wash detergent compartment (compartment nr. 2). If the anti-limescale is in tablet form, put only one tablet into compartment nr. 2. Dry the inside of the bellow with a clean piece of cloth after the programme has come to an end. Repeat Drum leaning process in every 2 months. Use an anti-limescale suitable for the washing machines. fter every washing make sure that no foreign substance is left in the drum. 1. Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine. If more than normal amount of water and softener mixture starts to gather in the softener compartment, the siphon must be cleaned. 2. Wash the detergent drawer and the siphon with plenty of lukewarm water in a washbasin. Wear protective gloves or use an appropriate brush to avoid touching of the residues in the drawer with your skin when cleaning. 3. Insert the drawer back into its place after cleaning and make sure that it is seated well. If the holes on the bellow shown in the figure is blocked, open the holes using a toothpick. Foreign metal substances will cause rust stains in the drum. lean the stains on the drum surface by using cleaning agents for stainless steel. Never use steel wool or wire wool. warning: Never use sponge or scrub materials. These will damage the painted and plastic surfaces. 5.3 leaning the body and control panel Wipe the body of the machine with soapy water or noncorrosive mild gel detergents as necessary, and dry with a soft cloth. Use only a soft and damp cloth to clean the control panel. 17 / EN Washing Machine / User s Manual

18 5.4 leaning the water intake filters There is a filter at the end of each water intake valve at the rear of the machine and also at the end of each water intake hose where they are connected to the tap. These filters prevent foreign substances and dirt in the water to enter the washing machine. Filters should be cleaned as they do get dirty. In order to clean the dirty filter and discharge the water: 1. Unplug the machine to cut off the supply power. warning: Temperature of the water inside the machine may rise up to 90 º. To avoid burning risk, filter must be cleaned after the water in the machine cools down. 2. Open the filter cap. If the filter cap is composed of two pieces, press the tab on the filter cap downwards and pull the piece out towards yourself. 1. lose the taps. 2. Remove the nuts of the water intake hoses to access the filters on the water intake valves. lean them with an appropriate brush. If the filters are too dirty, take them out by means of pliers and clean them. 3. Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under running water. 4. Replace the gaskets and filters carefully in their places and tighten the hose nuts by hand. 5.5 Draining remaining water and cleaning the pump filter The filter system in your machine prevents solid items such as buttons, coins and fabric fibers clogging the pump impeller during discharge of washing water. Thus, the water will be discharged without any problem and the service life of the pump will extend. If the machine fails to drain water, the pump filter is clogged. Filter must be cleaned whenever it is clogged or in every 3 months. Water must be drained off first to clean the pump filter. In addition, prior to transporting the machine (e.g., when moving to another house) and in case of freezing of the water, water may have to be drained completely. warning: Foreign substances left in the pump filter may damage your machine or may cause noise problem. If the filter cap is one piece, pull the cap from both sides at the top to open. You can remove the filter cover by slightly pushing downwards with a thin plastic tipped tool, through the gap above the filter cover. Do not use metal tipped tools to remove the cover. 3. Some of our products have emergency draining hose and some does not have. Follow the steps below to discharge the water. Discharging the water when the product has an emergency draining hose: a. Pull the emergency draining hose out from its seat b. Place a large container at the end of the hose. Drain the water into the container by pulling out the plug at the end of the hose. When the container is full, block the inlet of the hose by replacing the plug. fter the container is emptied, repeat the above procedure to drain the water in the machine completely. c. When draining of water is finished, close the end by the plug again and fix the hose in its place. d. Turn the pump filter to take it out. 18 / EN Washing Machine / User s Manual