MEX-1GP

Transcription

1 (1) Network Audio System Operating Instructions GB CS To cancel the demonstration (DEMO) display, see page 12. MEX-1GP 2006 Sony Corporation

2 Welcome! Thank you for purchasing this Sony Network Audio System. You can enjoy your drive with the following functions. Front panel with built-in flash memory GIGA PANEL You can play MP3/WMA files stored in the front panel with its built-in 1 GB flash memory. Audio files can be transferred from your computer to the front panel at high speed by USB connection. (Available OS are Windows XP and Windows 2000.) CD playback You can play CD-DA (also containing CD TEXT*), CD-R/CD-RW (MP3/WMA files also containing Multi Session (page 15)) and ATRAC CD (ATRAC3 and ATRAC3plus format (page 16)). Type of discs Label on the disc CD-DA MP3 WMA ATRAC CD Radio reception You can store up to 6 stations per band (FM1, FM2, FM3, MW and LW). BTM (Best Tuning Memory): the unit selects strong signal stations and stores them. Sound adjustment EQ3 stage2: You can choose any one of 7 preset equalizer curves. DSO (Dynamic Soundstage Organizer): creates a more ambient sound field, using virtual speaker synthesis, to enhance the sound of speakers, even if they are installed low in the door. BBE MP: improves digitally compressed sound such as MP3. (Only when playing a CD on this unit.) Optional unit operation You can also control optional CD/MD changers and optional Sony portable devices in addition to playing with this unit. * A CD TEXT disc is a CD-DA that includes information such as disc, artist and track name. Warning if your car s ignition has no ACC position After turning the ignition off, be sure to press and hold (OFF) on the unit until the display disappears. Otherwise, the display does not turn off and this causes battery drain. Sony is not responsible for damaged data due to problems of the GIGA PANEL or computer. This label is located on the bottom of the chassis. The ferrite core on the cable is for the purpose of the EMI reduction, please do not remove it. (Remarks: the ferrite core on the cable is the external type, it must be fixed on the cable.) Manufactured under license R from BBE Sound, Inc. The BBE MP process improves digitally compressed sound, such as MP3, by restoring and enhancing the higher harmonics lost through compression. BBE MP works by generating even-order harmonics from the source material, effectively recovering warmth, detail and nuance. SonicStage and its logo are trademarks of Sony Corporation. ATRAC, ATRAC3, ATRAC3plus and their logos are trademarks of Sony Corporation. Microsoft, Windows Media, and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. 2 For installation and connections, see the supplied installation/connections manual.

3 Table of Contents Getting Started Resetting the unit Setting the clock Detaching the front panel Attaching the front panel Inserting the disc in the unit Ejecting the disc Location of controls and basic operations Main unit Card remote commander RM-X CD/GIGA PANEL Display items Repeat and shuffle play Transferring audio files to the GIGA PANEL.. 8 Before using the GIGA PANEL Transferring audio files from the computer to the GIGA PANEL Deleting audio files in the GIGA PANEL.. 9 Radio Storing and receiving stations Storing automatically BTM Storing manually Receiving the stored stations Tuning automatically RDS Overview Setting AF and TA/TP Selecting PTY Setting CT Other functions Changing the sound settings Adjusting the sound characteristics BAL/FAD/SUB Customizing the equalizer curve EQ Adjusting setup items SET Using optional equipment CD/MD changer Rotary commander RM-X4S Auxiliary audio equipment Additional Information Precautions Notes on discs About MP3/WMA files About ATRAC CD Maintenance Removing the unit Specifications Troubleshooting Error displays/messages About EzRecover Installing EzRecover Formatting the GIGA PANEL

4 Getting Started Resetting the unit Before operating the unit for the first time, or after replacing the car battery or changing the connections, you must reset the unit. Detach the front panel and press the RESET button with a pointed object, such as a ballpoint pen. RESET button Note Pressing the RESET button will erase the clock setting and some stored contents. Setting the clock The clock uses a 24-hour digital indication. 1 Press and hold the select button. The setup display appears. 2 Press the select button repeatedly until CLOCK-ADJ appears. 3 Press (DSPL). The hour indication flashes. 4 Rotate the volume control dial to set the hour and minute. To move the digital indication, press (DSPL). 5 Press the select button. The clock starts and the next setup display appears. 6 Press and hold the select button. The setup is complete. To display the clock, press (DSPL). Press (DSPL) again to return to the previous display. With the card remote commander In step 4, to set the hour and minute, press M or m. Tip You can set the clock automatically with the RDS feature (page 11). Detaching the front panel You can detach the front panel of this unit to prevent theft. Caution alarm If you turn the ignition switch to the OFF position without detaching the front panel, the caution alarm will sound for a few seconds. The alarm will only sound if the built-in amplifier is used. 1 Press (OFF). The unit is turned off. 2 Press (OPEN). The front panel is flipped down. 3 Slide the front panel to the right, then gently pull out the left end of the front panel. 1 2 Notes Do not drop or put excessive pressure on the front panel and display window. Do not subject the front panel to heat/high temperature or moisture. Avoid leaving it in a parked car or on a dashboard/rear tray. 4

5 Attaching the front panel Place the hole A of the front panel onto the spindle B on the unit, then lightly push the left side in. Press (SOURCE) on the unit (or insert a disc) to operate the unit. Inserting the disc in the unit 1 Press (OPEN). 2 Insert the disc (label side up). B A 3 Close the front panel. Playback starts automatically. Ejecting the disc x 1 Press (OPEN). 2 Press Z. The disc is ejected. 3 Close the front panel. Note Do not put anything on the inner surface of the front panel. 5

6 Location of controls and basic operations Main unit MEX-1GP Front panel removed qk ql w; RESET Card remote commander RM-X151 1 qs wa qj ws OFF SOURCE DSPL SEL + ATT MODE SCRL VOL wd wf qd wg wh wj Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those on the unit. A OFF button To power off; stop the source. B Volume control dial/select button 12 To adjust volume (rotate); select setup items (press and rotate). C Receptor for the card remote commander D PTY (Programme Type) button 11 To select PTY in RDS. E Display window F DSO button 2 To select the DSO mode (1, 2, 3 or OFF). The larger the number, the more enhanced the effect. 6

7 G OPEN button 5 H GP* 1 /ALBM* 2 +/ buttons* 3 To skip groups/albums (press); skip groups/ albums continuously (press and hold). I SEEK /+ buttons CD: To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fastforward a track (press and hold). Radio: To tune in stations automatically (press); find a station manually (press and hold). J USB jack (Mini-B) 8 To connect to your computer. K SENS/BTM button 9 To improve weak reception: LOCAL/MONO (press); start the BTM function (press and hold). L SOURCE button To power on; change the source (GPL (GIGA PANEL)/Radio/CD/MD* 4 /AUX). M MODE button 9, 13 To select the radio band (FM/MW/LW)/ select the unit* 5. N AF (Alternative Frequencies)/TA (Traffic Announcement) button 10 To set AF and TA/TP in RDS. O Number buttons CD/MD* 4 : (3): REP 8 (4): SHUF 8 (5): BBE MP* 6 2 To activate the BBE MP function, set BBEMP-ON. To cancel, set BBEMP-OFF. (6): PAUSE* 7 To pause playback. To cancel, press again. Radio: To receive stored stations (press); store stations (press and hold). P EQ3 (equalizer) button 12 To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF). Q DSPL (display) button 8 To change display items. R RESET button 4 S Z (eject) button 5 To eject the disc. T Disc slot 5 To insert the disc. The following buttons on the card remote commander have also different buttons/functions from the unit. wa < (.)/, (>) buttons To control CD/radio, the same as (SEEK) /+ on the unit. ws VOL (volume) +/ button To adjust volume. wd ATT (attenuate) button To attenuate the sound. To cancel, press again. wf SEL (select) button The same as the select button on the unit. wg M (+)/m ( ) buttons To control CD, the same as (GP/ALBM) +/ on the unit. wh SCRL (scroll) button 8 To scroll the display item. wj Number buttons To receive stored stations (press); store stations (press and hold). *1 When an ATRAC CD is played. *2 When an MP3/WMA is played. *3 If the changer is connected, the operation is different, see page 13. *4 When an MD changer is connected. *5 When a CD/MD changer is connected. *6 Only when playing a CD on this unit. *7 When playing back on this unit. Note If the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first. Tip For details on how to replace the battery, see Replacing the lithium battery of the card remote commander on page 17. 7

8 CD/GIGA PANEL For details on selecting a CD/MD changer, see page 13. Note The GIGA PANEL will play MP3 and WMA files only. Display items *1 When an MP3/WMA is played. *2 When an ATRAC CD is played. *3 When a CD is played. *4 When GIGA PANEL is played. To return to normal play mode, select REP- OFF or SHUF-OFF. Transferring audio files to the GIGA PANEL Computer system requirements OS: Windows XP Windows 2000 (Other operating systems are not supported.) A ATRAC CD indication B Source C WMA/MP3/BBE MP indication D Track number/elapsed playing time, Disc/ artist name, Album/group number* 1, Album/ group name, Track name, Text information* 2, Clock *1 Album/group number is displayed only when the album/group is changed. *2 When playing an MP3, ID3 tag is displayed, when playing ATRAC CD, text information written by SonicStage, etc., is displayed, and when playing WMA, WMA tag is displayed. To change display items D, press (DSPL); scroll display items D, press (SCRL) on the card remote commander or set A.SCRL-ON (page 13). Tip Displayed items will differ, depending on the disc type, recorded format and settings. For details on MP3/ WMA, see page 15; ATRAC CD, see page 16. Repeat and shuffle play 1 During playback, press (3) (REP) or (4) (SHUF) repeatedly until the desired setting appears. Before using the GIGA PANEL Install EzRecover in your computer before transferring audio files from the computer to the GIGA PANEL. EzRecover is software that restructures the format of the GIGA PANEL should data become damaged for any reason during file transfer. For details on installation and usage of EzRecover, see page 22. Transferring audio files from the computer to the GIGA PANEL 1 Detach the front panel from the main unit (page 4). 2 Connect the front panel to your computer. Connect the small connector of the supplied USB cable to the USB jack on the front panel, then the large connector to a USB port on your computer. Access lamp 8 Select REP-TRACK REP-ALBM* 1 REP-GP* 2 SHUF-ALBM* 1 SHUF-GP* 2 SHUF-DISC* 3 SHUF-ALL* 4 To play track repeatedly. album repeatedly. group repeatedly. album in random order. group in random order. disc in random order. GIGA PANEL in random order. The GIGA PANEL is recognised as a removable disk (Sony GIGA PANEL USB Device). 3 Drag audio files you want to transfer to the GIGA PANEL and drop them to the removable disk. You can also transfer audio files to the GIGA PANEL by dragging a folder.

9 Tip The access lamp of the front panel is blinking while audio file is transferred. 4 Disconnect the front panel from your computer. Be sure to follow the operating method of your computer or OS when you disconnect the front panel from the computer. Example for Windows XP 1 Click the icon on the taskbar. The Safely remove USB Mass Storage Device message appears. 2 Click Safely remove USB Mass Storage Device. The message The USB Mass Storage Device device can now be safely removed from the system appears. 3 Disconnect the USB cable. 5 Attach the front panel to the main unit (page 5). Notes on the USB cable Do not connect the USB cable with the front panel attached to the main unit. Do not attach the front panel to the main unit with the USB cable connected. Do not disconnect the USB cable or remove the front panel while an audio file is being transferred. Use of the GIGA PANEL with a USB hub or a USB extension cable is not guaranteed. Always connect the GIGA PANEL to your computer directly using the supplied USB cable. Deleting audio files in the GIGA PANEL Connect the GIGA PANEL to your computer, and delete audio files you want to delete, as you would from a removable disk (GIGA PANEL). Radio Storing and receiving stations Caution When tuning in stations while driving, use Best Tuning Memory (BTM) to prevent an accident. Storing automatically BTM 1 Press (SOURCE) repeatedly until TUN appears. To change the band, press (MODE) repeatedly. You can select from FM1, FM2, FM3, MW or LW. 2 Press and hold (BTM) until BTM flashes. The unit stores stations in order of frequency on the number buttons. A beep sounds when the setting is stored. Storing manually 1 While receiving the station that you want to store, press and hold a number button ((1) to (6)) until MEM appears. The number button indication appears in the display. Note If you try to store another station on the same number button, the previously stored station will be replaced. Tip When a RDS station is stored, the AF/TA setting is also stored (page 10). Receiving the stored stations 1 Select the band, then press a number button ((1) to (6)). Tuning automatically 1 Select the band, then press (SEEK) /+ to search for the station. Scanning stops when the unit receives a station. Repeat this procedure until the desired station is received. Tip If you know the frequency of the station you want to listen to, press and hold (SEEK) /+ to locate the approximate frequency, then press (SEEK) /+ repeatedly to fine adjust to the desired frequency (manual tuning). 9

10 RDS Overview FM stations with Radio Data System (RDS) service send inaudible digital information along with the regular radio programme signal. Display items A Radio band, Function B TA/TP* 1 C Frequency* 2 (Programme service name), Preset number, Clock, RDS data *1 TA flashes during traffic information. TP lights up while such a station is received. *2 While receiving the RDS station, * is displayed on the left of the frequency indication. To change display items C, press (DSPL). RDS services This unit automatically provides RDS services as follows: AF (Alternative Frequencies) Selects and retunes the station with the strongest signal in a network. By using this function, you can continuously listen to the same programme during a long-distance drive without having to retune the same station manually. TA (Traffic Announcement)/TP (Traffic Programme) Provides current traffic information/ programmes. Any information/programme received, will interrupt the currently selected source. PTY (Programme Types) Displays the currently received programme type. Also searches your selected programme type. CT (Clock Time) The CT data from the RDS transmission sets the clock. Notes Depending on the country/region, not all RDS functions may be available. RDS will not work if the signal strength is too weak, or if the station you are tuned to is not transmitting RDS data. Setting AF and TA/TP 1 Press (AF/TA) repeatedly until the desired setting appears. Select AF-ON TA-ON AF, TA-ON AF, TA-OFF To activate AF and deactivate TA. activate TA and deactivate AF. activate both AF and TA. deactivate both AF and TA. Storing RDS stations with the AF and TA setting You can preset RDS stations along with the AF/ TA setting. If you use the BTM function, only RDS stations are stored with the same AF/TA setting. If you preset manually, you can preset both RDS and non-rds stations with the AF/TA setting for each. 1 Set AF/TA, then store the station with BTM or manually. Presetting the volume of traffic announcements You can preset the volume level of the traffic announcements so as to not miss hearing them. 1 Rotate the volume control dial to adjust the volume level. 2 Press and hold (AF/TA) until TA appears. Receiving emergency announcements With AF or TA on, the emergency announcements will automatically interrupt the currently selected source. 10

11 Staying with one regional programme REG When the AF function is on: this unit s factory setting restricts reception to a specific region, so you will not be switched to another regional station with a stronger frequency. If you leave this regional programme s reception area, set REG-OFF in setup (page 13). Note This function does not work in the UK and in some other areas. Local Link function (UK only) This function enables you to select other local stations in the area, even if they are not stored on your number buttons. 1 During FM reception, press a number button ((1) to (6)) on which a local station is stored. 2 Within 5 seconds, press again a number button of the local station. Repeat this procedure until the local station is received. Selecting PTY 1 Press (PTY) during FM reception. Type of programmes NEWS (News), AFFAIRS (Current Affairs), INFO (Information), SPORT (Sports), EDUCATE (Education), DRAMA (Drama), CULTURE (Culture), SCIENCE (Science), VARIED (Varied), POP M (Popular Music), ROCK M (Rock Music), EASY M (Easy Listening), LIGHT M (Light Classical), CLASSICS (Classical), OTHER M (Other Music Type), WEATHER (Weather), FINANCE (Finance), CHILDREN (Children s Programmes), SOCIAL A (Social Affairs), RELIGION (Religion), PHONE IN (Phone In), TRAVEL (Travel), LEISURE (Leisure), JAZZ (Jazz Music), COUNTRY (Country Music), NATION M (National Music), OLDIES (Oldies Music), FOLK M (Folk Music), DOCUMENT (Documentary) Note You cannot use this function in countries/regions where no PTY data is available. Setting CT 1 Set CT-ON in setup (page 12). Notes The CT function may not work even though an RDS station is being received. There might be a difference between the time set by the CT function and the actual time. The current programme type name appears if the station is transmitting PTY data. 2 Press (PTY) repeatedly until the desired programme type appears. 3 Press (SEEK) /+. The unit starts to search for a station broadcasting the selected programme type. 11

12 12 Other functions Changing the sound settings Adjusting the sound characteristics BAL/FAD/SUB You can adjust the balance, fader, and subwoofer volume. 1 Press the select button repeatedly until BAL, FAD or SUB appears. The item changes as follows: LOW* 1 t MID* 1 t HI* 1 t BAL (left-right) t FAD (front-rear) t SUB (subwoofer volume)* 2 t AUX* 3 *1 When EQ3 is activated (page 12). *2 When the audio output is set to SUB (page 12). ATT is displayed at the lowest setting, and can be adjusted up to 20 steps. *3 When AUX source is activated (page 14). 2 Rotate the volume control dial to adjust the selected item. After 3 seconds, the setting is complete and the display returns to normal play/reception mode. Customizing the equalizer curve EQ3 CUSTOM of EQ3 allows you to make your own equalizer settings. 1 Select a source, then press (EQ3) repeatedly to select CUSTOM. 2 Press the select button repeatedly until LOW, MID or HI appears. 3 Rotate the volume control dial to adjust the selected item. The volume level is adjustable in 1 db steps, from 10 db to +10 db. Repeat steps 2 and 3 to adjust the equalizer curve. To restore the factory-set equalizer curve, press and hold the select button before the setting is complete. After 3 seconds, the setting is complete and the display returns to normal play/reception mode. Tip Other equalizer types are also adjustable. Adjusting setup items SET 1 Press and hold the select button. The setup display appears. 2 Press the select button repeatedly until the desired item appears. 3 Rotate the volume control dial to select the setting (example ON or OFF ). 4 Press and hold the select button. The setup is complete and the display returns to normal play/reception mode. Note Displayed items will differ, depending on the source and setting. With the card remote commander In step 3, to select the setting, press < or,. The following items can be set (follow the page reference for details): z indicates the default settings. CLOCK-ADJ (Clock Adjust) (page 4) CT (Clock Time) To set CT-ON or CT-OFF (z) (page 10, 11). BEEP To set BEEP-ON (z) or BEEP-OFF. AUX-A* 1 (AUX Audio) To turn the AUX source display AUX-A-ON (z) or AUX-A-OFF (page 14). SUB/REAR* 1 To switch the audio output. SUB-OUT (z): to output to a subwoofer. REAR-OUT : to output to a power amplifier. DIM (Dimmer) To change the brightness of the display. DIM-AT (z): to dim the display automatically when you turn lights on. DIM-ON : to dim the display. DIM-OFF : to deactivate the dimmer. CONTRAST To adjust the contrast of the display. The contrast level is adjustable in 7 steps. M.DSPL (Motion Display) To select the Motion Display mode. M.DSPL-SA (z): to show moving patterns and spectrum analyzer. M.DSPL-ON : to show moving patterns. M.DSPL-OFF : to deactivate the Motion Display. DEMO* 1 (Demonstration) To set DEMO-ON (z) or DEMO-OFF.

13 A.SCRL (Auto Scroll) To scroll long displayed item automatically when the disc/group/track/album is changed. A.SCRL-ON : to scroll. A.SCRL-OFF (z): to not scroll. REG* 2 To set REG-ON (z) or REG-OFF (page 11). LPF* 3 (Low Pass Filter) To select the subwoofer cut-off frequency: LPF OFF (z), LPF125Hz or LPF 78Hz. *1 When the unit is turned off. *2 When FM is received. *3 When the audio output is set to SUB. Using optional equipment CD/MD changer Selecting the changer 1 Press (SOURCE) repeatedly until CD or MD appears. 2 Press (MODE) repeatedly until the desired changer appears. Unit number Repeat and shuffle play 1 During playback, press (3) (REP) or (4) (SHUF) repeatedly until the desired setting appears. Select REP-DISC* 1 SHUF- CHGR* 1 SHUF-ALL* 2 To play disc repeatedly. tracks in the changer in random order. tracks in all units in random order. *1 When one or more CD/MD changers are connected. *2 When one or more CD changers, or two or more MD changers are connected. To return to normal play mode, select REP- OFF or SHUF-OFF. Tip SHUF-ALL will not shuffle tracks between CD units and MD changers. Rotary commander RM-X4S Attaching the label Attach the indication label depending on how you mount the rotary commander. Playback starts. Skipping albums and discs 1 During playback, press (GP/ALBM) +/. To skip album Disc number album continuously discs discs continuously Press (GP/ALBM) and release (hold for a moment). within 2 seconds of first releasing. repeatedly. then, press again within 2 seconds and hold. SEL MODE DSPL Location of controls The corresponding buttons on the rotary commander control the same functions as those on this unit. SOURCE PRESET/ DISC VOL SEL DSPL MODE SEL ATT DSPL SEEK/AMS MODE OFF The following controls on the rotary commander require a different operation from the unit. OFF continue to next page t 13

14 PRESET/DISC control The same as (GP/ALBM) +/ on the unit (push in and rotate). VOL (volume) control The same as the volume control dial on the unit (rotate). SEEK/AMS control The same as (SEEK) /+ on the unit (rotate, or rotate and hold). Changing the operative direction The operative direction of the controls is factoryset as shown below. To increase To decrease If you need to mount the rotary commander on the right hand side of the steering column, you can reverse the operative direction. 1 While pushing the VOL control, press and hold (SEL). Auxiliary audio equipment You can connect optional Sony portable devices to the BUS AUDIO IN/AUX IN terminal on the unit. If the changer or other device is not connected to the terminal, the unit allows you to listen to the portable device on your car speakers. Note When connecting a portable device, be sure BUS CONTROL IN is not connected. If a device is connected to BUS CONTROL IN, AUX cannot be selected as source. Tip When connecting both a portable device and a changer, use the optional AUX-IN selector. Selecting auxiliary equipment 1 Press (SOURCE) repeatedly until AUX AUDIO appears. Operate by the portable device itself. Adjust the volume level Be sure to adjust the volume for each connected audio device before playback. 1 Turn down the volume on the unit. 2 Press (SOURCE) repeatedly until AUX AUDIO appears. 3 Start playback of the portable audio device at a moderate volume. 4 Set your usual listening volume on the unit. 5 Press the select button repeatedly until AUX appears, and rotate the volume control dial to adjust the input level (±6 db). 14

15 Additional Information Precautions If your car has been parked in direct sunlight, allow the unit to cool off before operating it. Power aerial will extend automatically while the unit is operating. Moisture condensation On a rainy day or in a very damp area, moisture condensation may occur inside the lenses and display of the unit. Should this occur, the unit will not operate properly. In such a case, remove the disc and wait for about an hour until the moisture has evaporated. To maintain high sound quality Be careful not to splash juice or other soft drinks onto the unit or discs. Notes on discs To keep a disc clean, do not touch its surface. Handle the disc by its edge. Keep your discs in their cases or disc magazines when not in use. Do not subject discs to heat/high temperature. Avoid leaving them in a parked car or on a dashboard/rear tray. Do not attach labels, or use discs with sticky ink/ residue. Such discs may stop spinning when used, causing a malfunction, or may ruin the disc. Before playing, clean the discs with a commercially available cleaning cloth. Wipe each disc from the centre out. Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray intended for analogue discs. Notes on CD-R/CD-RW discs Some CD-Rs/CD-RWs (depending on the equipment used for its recording or the condition of the disc) may not play on this unit. You cannot play a CD-R/a CD-RW that is not finalized. Music discs encoded with copyright protection technologies This product is designed to play back discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product. Note on DualDiscs A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital audio material on the other side. However, since the audio material side does not conform to the Compact Disc (CD) standard, playback on this product is not guaranteed. Do not use any discs with labels or stickers attached. The following malfunctions may result from using such discs: Inability to eject a disc (due to a label or sticker peeling off and jamming the eject mechanism). Inability to read audio data correctly (e.g., playback skipping, or no playback) due to heat shrinking of a sticker or label causing a disc to warp. Discs with non-standard shapes (e.g., heart, square, star) cannot be played on this unit. Attempting to do so may damage the unit. Do not use such discs. You cannot play 8 cm CDs. About MP3/WMA files MP3, which stands for MPEG-1 Audio Layer-3, is a music file compression format standard. It compresses audio CD data to approximately 1/10 of its original size. WMA, which stands for Windows Media Audio, is another music file compression format standard. It compresses audio CD data to approximately 1/22* of its original size. * only for 64 kbps CD The unit is compatible with the ISO 9660 level 1/ level 2 format, Joliet/Romeo in the expansion format, and Multi Session. The maximum number of: folders (albums): 150 (including root and empty folders). MP3/WMA files (tracks) and folders contained in a disc: 300 (if a folder/file names contain many characters, this number may become less than 300). displayable characters for a folder/file name is 32 (Joliet), or 64 (Romeo). continue to next page t 15

16 ID3 tag versions 1.0, 1.1, 2.2, 2.3 and 2.4 apply to MP3 only. ID3 tag is 15/30 characters (1.0 and 1.1), or 63/126 characters (2.2, 2.3 and 2.4). WMA tag is 63 characters. GIGA PANEL The maximum number of: folders (albums): 200 (including root and empty folders). MP3/WMA files (tracks) and folders: 500 (if a folder/file names contain many characters, this number may become less than 500). displayble characters for a folder/file name: 64 ID3 tag versions 1.0, 1.1, 2.2, 2.3 and 2.4 apply to MP3 only. ID3 tag is 15/30 characters (1.0 and 1.1), or 63/126 characters (2.2, 2.3 and 2.4). WMA tag is 63 characters. Playback order of MP3/WMA files CD GIGA PANEL MP3/WMA MP3/WMA Folder (album) MP3/WMA file (track) Folder (album) MP3/WMA file (track) Notes When naming an MP3 file/wma file, be sure to add the file extension.mp3 /.wma to the file name. During playback of a VBR (variable bit rate) MP3/ WMA file or fast-forward/reverse, elapsed playing time may not display accurately. When the disc is recorded in Multi Session, only the first track of the first session format is recognised and played (any other format is skipped). The priority of the format is CD-DA, ATRAC CD and MP3/WMA. When the first track is a CD-DA, only CD-DA of the first session is played. When the first track is not a CD-DA, an ATRAC CD or MP3/WMA session is played. If the disc has no data in any of these formats, NO MUSIC is displayed. When the GIGA PANEL is played, playback order may not appear the same as the display of the Windows Explorer screen. Notes on MP3 Be sure to finalize the disc before using on the unit. If you play a high-bit-rate MP3, such as 320 kbps, sound may be intermittent. Notes on WMA Files made with lossless compression are not playable. Files protected by copyright are not playable. About ATRAC CD ATRAC3plus format ATRAC3, which stands for Adaptive Transform Acoustic Coding3, is audio compression technology. It compresses audio CD data to approximately 1/10 of its original size. ATRAC3plus, which is an extended format of ATRAC3, compresses the audio CD data to approximately 1/20 of its original size. The unit accepts both ATRAC3 and ATRAC3plus format. ATRAC CD ATRAC CD is recorded audio CD data which is compressed to ATRAC3 or ATRAC3plus format using authorized software, such as SonicStage 2.0 or later, or SonicStage Simple Burner. The maximum number of: folders (groups): 255 files (tracks): 999 The characters for a folder/file name and text information written by SonicStage is displayed. For details on ATRAC CD, see the SonicStage or SonicStage Simple Burner manual. Note Be sure to create the ATRAC CD using authorized software, such as SonicStage 2.0 or later, or SonicStage Simple Burner 1.0 or 1.1. If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer. 16

17 Maintenance Replacing the lithium battery of the card remote commander Under normal conditions, the battery will last approximately 1 year. (The service life may be shorter, depending on the conditions of use.) When the battery becomes weak, the range of the card remote commander becomes shorter. Replace the battery with a new CR2025 lithium battery. Use of any other battery may present a risk of fire or explosion. 1 2 c + side up Notes on the lithium battery Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately consult a doctor. Wipe the battery with a dry cloth to assure a good contact. Be sure to observe the correct polarity when installing the battery. Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur. WARNING Battery may explode if mistreated. Do not recharge, disassemble, or dispose of in fire. Cleaning the connectors The unit may not function properly if the connectors between the unit and the front panel are not clean. In order to prevent this, detach the front panel (page 4) and clean the connectors with a cotton swab dipped in alcohol. Do not apply too much force. Otherwise, the connectors may be damaged. Main unit Notes For safety, turn off the ignition before cleaning the connectors, and remove the key from the ignition switch. Never touch the connectors directly with your fingers or with any metal device. Removing the unit Back of the front panel 1 Remove the protection collar. 1 Detach the front panel (page 4). 2 Engage the release keys together with the protection collar. Fuse replacement When replacing the fuse, be sure to use one matching the amperage rating stated on the original fuse. If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer. Fuse (10A) Orient the release keys as shown. 3 Pull out the release keys to remove the protection collar. continue to next page t 17

18 2 Remove the unit. 1 Insert both release keys simultaneously until they click. 2 Pull the release keys to unseat the unit. 3 Slide the unit out of the mounting. Specifications CD Player section Signal-to-noise ratio: 120 db Frequency response: 10 20,000 Hz Wow and flutter: Below measurable limit GIGA PANEL section Signal-to-noise ratio: 120 db Frequency response: 10 20,000 Hz Tuner section Hook facing inwards. FM Tuning range: MHz Aerial terminal: External aerial connector Intermediate frequency: 10.7 MHz/450 khz Usable sensitivity: 9 dbf Selectivity: 75 db at 400 khz Signal-to-noise ratio: 67 db (stereo), 69 db (mono) Harmonic distortion at 1 khz: 0.5 % (stereo), 0.3 % (mono) Separation: 35 db at 1 khz Frequency response: 30 15,000 Hz Power amplifier section Outputs: Speaker outputs (sure seal connectors) Speaker impedance: 4 8 ohms Maximum power output: 52 W 4 (at 4 ohms) General Outputs: Audio outputs terminal (front, sub/rear switchable) Power aerial relay control terminal Power amplifier control terminal Inputs: Telephone ATT control terminal Illumination control terminal BUS control input terminal BUS audio input/aux IN terminal Remote controller input terminal Aerial input terminal USB jack (Mini-B) Tone controls: Low: ±10 db at 60 Hz (XPLOD) Mid: ±10 db at 1 khz (XPLOD) High: ±10 db at 10 khz (XPLOD) Power requirements: 12 V DC car battery (negative earth) Dimensions: Approx mm (w/h/d) Mounting dimensions: Approx mm (w/h/d) Mass: Approx. 1.2 kg Supplied accessories: Card remote commander: RM-X151 Parts for installation and connections (1 set) USB cable (1) Optional accessories/equipment: Rotary commander: RM-X4S BUS cable (supplied with an RCA pin cord): RC-61 (1 m), RC-62 (2 m) CD changer (10 discs): CDX-757MX, CDX-656X Source selector: XA-C30, XA-C40 AUX-IN selector: XA-300 Your dealer may not handle some of the above listed accessories. Please ask the dealer for detailed information. US and foreign patents licensed from Dolby Laboratories. MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson. Note This unit cannot be connected to a digital preamplifier or an equalizer which is Sony BUS system compatible. Design and specifications are subject to change without notice. 18 MW/LW Tuning range: MW: 531 1,602 khz LW: khz Aerial terminal: External aerial connector Intermediate frequency: 10.7 MHz/450 khz Sensitivity: MW: 30 µv, LW: 40 µv

19 Lead-free solder is used for soldering certain parts. (more than 80 %) Halogenated flame retardants are not used in the certain printed wiring boards. Halogenated flame retardants are not used in cabinets. VOC (Volatile Organic Compound)-free vegetable oil based ink is used for printing the carton. Packaging cushions do not use polystyrene foam. Troubleshooting The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. General No power is being supplied to the unit. Check the connection. If everything is in order, check the fuse. If the unit is turned off and the display disappears, it cannot be operated with the remote commander. t Turn on the unit. The power aerial does not extend. The power aerial does not have a relay box. No sound. The volume is too low. The ATT function is activated, or the Telephone ATT function (when the interface cable of a car telephone is connected to the ATT lead) is activated. The position of the fader control FAD is not set for a 2-speaker system. The CD changer is incompatible with the disc format (MP3/WMA/ATRAC CD). t Play back with a Sony MP3 compatible CD changer, or this unit. No beep sound. The beep sound is cancelled (page 12). An optional power amplifier is connected and you are not using the built-in amplifier. The contents of the memory have been erased. The RESET button has been pressed. t Store again into the memory. The power connecting lead or battery has been disconnected. The power connecting lead is not connected properly. Stored stations and correct time are erased. The fuse has blown. Makes noise when the position of the ignition key is switched. The leads are not matched correctly with the car s accessory power connector. The display disappears from/does not appear in the display window. The dimmer is set DIM-ON (page 12). The display disappears if you press and hold (OFF). t Press and hold (OFF) on the unit until the display appears. The connectors are dirty (page 17). DSO does not function. Depending on the type of car interior or type of music, DSO may not have a desirable effect. CD/MD playback The disc cannot be loaded. Another disc is already loaded. The disc has been forcibly inserted upside down or in the wrong way. The disc does not playback. Defective or dirty disc. The CD-Rs/CD-RWs are not for audio use (page 15). MP3/WMA files cannot be played back. The disc is incompatible with the MP3/WMA format and version (page 15). MP3/WMA files take longer to play back than others. The following discs take a longer time to start playback. a disc recorded with a complicated tree structure. a disc recorded in Multi Session. a disc to which data can be added. The ATRAC CD cannot play. The disc is not created by authorized software, such as SonicStage or SonicStage Simple Burner. Tracks that are not included in the group cannot be played. The display items do not scroll. For discs with very many characters, those may not scroll. A.SCRL is set to OFF. t Set A.SCRL-ON (page 13) or press (SCRL) on the card remote commander. The sound skips. Installation is not correct. t Install the unit at an angle of less than 45 in a sturdy part of the car. Defective or dirty disc. The operation buttons do not function. The disc will not eject. Press the RESET button (page 4). MS or MD does not appear on the source display when both the optional MGS-X1 and MD changer are connected. This unit recognises MGS-X1 as an MD unit. t Press (SOURCE) until MS or MD appears, then press (MODE) repeatedly. continue to next page t 19

20 20 GIGA PANEL playback The GIGA PANEL is not recognised by the computer when it is connected to the computer. The USB cable is disconnected. t Connect the USB cable. MP3/WMA file cannot be transferred to the GIGA PANEL. The USB cable is not connected properly. t Connect the USB cable properly. There is insufficient free space on the GIGA PANEL to transfer audio files. t Delete any unnecessary audio files or transfer files to your computer to increase free space. Audio files with a limited playing period or playing count may not be transferred due to restrictions set by copyright holders. For details on the settings of each audio file, contact the distributor. The number of audio files that can be transferred is limited. (Available recording time is short.) There is insufficient free space on the GIGA PANEL to transfer audio files. t Delete any unnecessary audio files or transfer files to your computer to increase free space. Non-audio data is stored in the GIGA PANEL to where you want to transfer audio files. t Delete non-audio data or transfer it to your computer to increase free space. Operation becomes unstable with the GIGA PANEL connected to the computer. USB hub or USB extension cable is used. t Connecting via a USB hub or USB extension is not guaranteed. Connect the supplied USB cable directly to the computer. The file cannot be copied from the computer. The file in the GIGA PANEL cannot be recognized by the computer. Format the GIGA PANEL using EzRecover (page 22). The GIGA PANEL does not playback. The file is protected by DRM (Digital Rights Management). The file is other than MP3/WMA format. Radio reception The stations cannot be received. The sound is hampered by noises. Connect a power aerial control lead (blue) or accessory power supply lead (red) to the power supply lead of a car s aerial booster (only when your car has built-in FM/MW/LW aerial in the rear/side glass). Check the connection of the car aerial. The auto aerial will not go up. t Check the connection of the power aerial control lead. Check the frequency. When the DSO mode is on, the sound is sometimes hampered by noises. t Set the DSO mode to OFF (page 6). Preset tuning is not possible. Store the correct frequency in the memory. The broadcast signal is too weak. Automatic tuning is not possible. Setting of the local seek mode is not correct. t Tuning stops too frequently: Press (SENS) until LOCAL-ON appears. t Tuning does not stop at a station: Press (SENS) repeatedly until MONO-ON or MONO-OFF (FM), or LOCAL-OFF (MW/ LW) appears. The broadcast signal is too weak. t Perform manual tuning. During FM reception, the ST indication flashes. Tune in the frequency accurately. The broadcast signal is too weak. t Press (SENS) to set the monaural reception mode to MONO-ON. An FM programme broadcast in stereo is heard in monaural. The unit is in monaural reception mode. t Press (SENS) until MONO-OFF appears. RDS The SEEK starts after a few seconds of listening. The station is non-tp or has weak signal. t Deactivate TA (page 10). No traffic announcements. Activate TA (page 10). The station does not broadcast any traffic announcements despite being TP. t Tune in another station. PTY displays The current station is not an RDS station. RDS data has not been received. The station does not specify the programme type. Error displays/messages BLANK* 1 Tracks have not been recorded on the MD.* 2 t Play an MD with recorded tracks. ERROR* 1 The disc is dirty or inserted upside down.* 2 t Clean or insert the disc correctly. A blank disc has been inserted. The disc cannot play because of some problem. t Insert another disc. FAILURE The connection of speakers/amplifiers is incorrect. t See the installation guide manual of this model to check the connection. FAT-ERROR There is a problem with the file system of the flash memory. t Format the flash memory (page 22). If the problem persists, consult your nearest Sony dealer.

21 FS ERROR A file system other than EzRecover is being used for the flash memory. t Format the flash memory (page 22). LOAD The changer is loading the disc. t Wait until loading is complete. L. SEEK +/ The local seek mode is on during automatic tuning. NO AF There is no alternative frequency for the current station. t Press (SEEK) /+ while the programme service name is flashing. The unit starts searching for another frequency with the same PI (Programme Identification) data ( PI SEEK appears). NO DISC The disc is not inserted in the CD/MD changer. t Insert discs in the changer. NO ID3 ID3 tag information is not written in the MP3 file. NO INFO Text information is not written in the ATRAC3/ ATRAC3plus or WMA file. NO MAG The disc magazine is not inserted in the CD changer. t Insert the magazine in the changer. NO MUSIC The disc is not a music file. t Insert a music CD in this unit or MP3 playable changer. There are no music files in the flash memory. t Transfer music files from your computer. NO NAME A track/album/group/disc name is not written in the track. NO TP The unit will continue searching for available TP stations. NOT READ The disc information has not been read by the unit. t Load the disc, then select it on the list. NOTREADY The lid of the MD changer is open or the MDs are not inserted properly. t Close the lid or insert the MDs properly. OFFSET There may be an internal malfunction. t Check the connection. If the error indication remains on in the display, consult your nearest Sony dealer. READ The unit is reading all track and album/group information on the disc/flash memory. t Wait until reading is complete and playback starts automatically. Depending on the disc/flash memory structure, it may take more than a minute. RESET The CD unit and CD/MD changer cannot be operated because of some problem. t Press the RESET button (page 4). or During reverse or fast-forward, you have reached the beginning or the end of the disc and you cannot go any further. The character cannot be displayed with the unit. *1 If an error occurs during playback of a CD or MD, the disc number of the CD or MD does not appear in the display. *2 The disc number of the disc causing the error appears in the display. If these solutions do not help improve the situation, consult your nearest Sony dealer. If you take the unit to be repaired because of CD playback trouble, bring the disc that was used at the time the problem began. 21

22 About EzRecover Notes EzRecover is stored in the GIGA PANEL. Be sure to install EzRecover in your computer before the first file is transferred. If file damage occurs, EzRecover cannot be installed in your computer. Audio files cannot be restored with EzRecover. When formatted with EzRecover, all files in the GIGA PANEL are deleted. Computer system requirements OS: Windows XP, Windows 2000 Language: English, German, French, Italian, Dutch, Spanish, Korean, Chinese (Simplified), Chinese (Traditional) Installing EzRecover 1 Connect the GIGA PANEL to your computer with the supplied USB cable. 2 When the Removable Disk window opens, EzRecover in the GIGA PANEL is copied to the computer. If the Removable Disk window does not open, click My Computer - Removable Disk on your computer. 3 Double-click EzRecover on the computer. The EzRecover - InstallShield Wizard dialog box appears. 4 Click Next >. 5 Check I accept the terms of the license agreement. 6 Click Next >. Program installation starts. 7 Click Finish. Formatting the GIGA PANEL 1 Click start, point to All Programs - Sony EzRecover, and then click EzRecover. 2 Connect the GIGA PANEL to your computer with the supplied USB cable. 3 Check Format Disk. 4 Click OK. Format starts. When the format has completed, quit EzRecover and disconnect the USB cable. Tip If you delete EzRecover, it can be downloaded from the following site. Uninstalling EzRecover 1 Double click EzRecover on the computer. 2 Follow the instructions on the screen to uninstall EzRecover. 22

23

24 鸣谢惠顾! 感谢您惠购 Sony 网络音频系统 使用以下功能, 您可以享受驾驶的乐趣 带有内置闪存的前面板 GIGA PANEL 您可以播放储存在前面板内置 1 GB 闪存中的 MP3/WMA 文件 可通过高速 USB 连接将音频文件从电脑传送至前面板 ( 可用操作系统 :Windows XP 和 Windows 2000 ) CD 播放您可播放 CD-DA ( 也包含 CD TEXT*) CD-R/CD-RW ( 也包含 Multi Session 的 MP3/WMA 文件 ( 第 15 页 )) 和 ATRAC CD (ATRAC3 和 ATRAC3plus 格式 ( 第 16 页 )) 光盘类型光盘上的标签 CD-DA Sony 对于因 GIGA PANEL 或计算机的问题而造成的数据损坏不承担责任 电缆上的铁氧体磁心用于减少 EMI, 请勿将其拆卸 ( 备注 : 电缆上的铁氧体磁心属于外接类型, 必须固定在电缆上 ) R MP3 WMA ATRAC CD 无线电接收 每个波段 (FM1 FM2 FM3 MW 和 LW) 最多可以储存 6 个电台 BTM ( 最佳调谐记忆功能 ): 本机选择信号强的电台并储存 声音调整 EQ3 stage2: 您可以选择 7 个预设均衡曲线中任何一个 DSO (Dynamic Soundstage Organizer): 采用虚拟扬声器合成创建更具现场环境的声场, 即使扬声器安装在门上较低的位置, 也可以增强扬声器声音 BBE MP: 改善数字压缩声音, 如 MP3 ( 仅在本机上播放 CD 时 ) 选购装置操作除了用本机进行播放之外, 您还可以控制选购的 CD/MD 换碟机和选购的 Sony 便携式设备 * CD TEXT 光盘是含有光盘 艺术家和曲目名称等信息的 CD-DA SonicStage 及其标志是 Sony Corporation 的商标 ATRAC ATRAC3 ATRAC3plus 及它们的标志是 Sony Corporation 的商标 2

25 目录 入门指南 重设本机 设定时钟 拆卸前面板 安装前面板 将光盘插入本机 退出光盘 控制器位置和基本操作 主机 卡片式遥控器 RM- X CD/GIGA PANEL 显示项目 重复和随机播放 传送音频文件至 GIGA PANEL 使用 GIGA PANEL 之前 将音频文件从计算机传送至 GIGA PANEL 删除 GIGA PANEL 中的音频文件 收音机 其他功能 更改声音设定 调整声音特性 - BAL/FAD/SUB 自定义均衡曲线 - EQ 调整设定项目 - SET 使用选购设备 CD/MD 换碟机 旋转式遥控器 RM-X4S 辅助音频设备 附加信息 使用前注意事项 光盘注意事项 关于 MP3/WMA 文件 关于 ATRAC CD 保养 取出本机 规格 故障排除 出错显示 / 信息 关于 EzRecover 安装 EzRecover 格式化 GIGA PANEL 储存并接收电台 自动储存 - BTM 手动储存 收听已储存的电台 自动调谐 RDS 概述 设定 AF 和 TA/TP 选择 PTY 设定 CT