Transcription

1 INSTRUCTIONS HITACHI Ion cleansing with moisturizing support device CM-N8900BF For household use only AC/RECHARGEABLE V AC FREE VOLTAGE Made in Japan

2

3 English Page 1~14 15~27

4 English Safety precautions Precautions described here are intended for safe and correct use of this product and are to prevent injury and damage to you and others before they occur. Precautions are classified as follows. Make sure to observe the precautions because they are all important in relation to safety. <Examples of pictorial indication> Prohibited Prohibited "Disassembly prohibited" "Use with wet hands prohibited" The symbol indicates "Compulsory" (Make sure to do this). "General action" Indicates an imminently dangerous situation in which improper handling may result in death or serious injury to a user. Indicates a dangerous situation in which improper handling could result in death or serious injury to a user. Indicates a dangerous situation in which improper handling could result in slight injury to a user or damage to property (house, household effects, etc.). The symbol indicates "Prohibited" (Do not do this). "Unplug" "Use prohibited in wet areas" Persons who use the following medical electronic devices should not use this product. (This product may cause the medical electronic devices to malfunction.) - Self-contained medical electronic devices such as a pacemaker - Wearable medical electronic devices such as an electrocardiograph Never use this product by other methods which are not described in this instruction manual. (Cause of an accident, trouble, or failure) Use this product only for face and neck. (Cause of an accident or trouble) The following persons should avoid use of this product. (Cause of an accident or trouble) - Persons with heart disease - Persons with an acute (pain) illness - Persons with a fever - Persons with a blood pressure disorder - Persons with an infectious disease - Persons with a tubercular disease - Persons with a malignant tumor - Persons with facial neuralgia - Persons who are pregnant - Persons who are menstruating - Persons with atopic dermatitis - Persons with an allergic predisposition - Persons with particularly sensitive skin - Persons with hemophilia - Persons under dental care - Persons whose blood vessels have expanded due to long time use of steroid hormones or liver function disorder - Persons who are under the influence of alcohol or medication, or who are very tired Prohibited Make sure Unplug Prohibited Make sure Use with wet hands prohibited Do not use this product on the following regions. (Cause of an accident or trouble) - Regions where orthopedic treatment was given - Eyeballs and upper eyelids - Wound sites - Facial melanoderma - Mucosal regions, such as inside the mouth - Regions irritated due to pimples or skin rash - Regions which suffer from sensation of pain or perception disorder - Regions where metal, plastic or silicone etc., is embedded under skin - Regions where there is itching, sensation of warmth, or liver spots due to physical stimulus etc. - Regions where skin irritation is caused by cosmetics This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. When feeling pain or disorder during use of this product, or sensing anything wrong with your skin after use, stop using this product and consult a dermatologist. (Cause of skin trouble etc.) If any abnormality occurs during charge or use, immediately pull out the power plug of the power adaptor from the outlet. (Cause of an accident or fire) Use only V AC for power supply. (Cause of a fire or electric shock) Never use if the power cord or the power plug is damaged or its insertion to the outlet is loose. (If the power cord breaks, a fire or electric shock may occur.) Never damage the power cord, unnecessarily bend, pull, twist, bind, place a heavy object on it, pinch, process, or wind around the power adaptor, etc. (If the power cord breaks, a fire or electric shock may occur.) Do not use this product near inflammable substances (gasoline, benzene, thinner, etc.). (Cause of explosion or fire) If any unusual sound or abnormality occurs in the main body, immediately stop using this product and contact the distributor for repair together with the power adaptor. (Cause of an accident or trouble) Follow the description of the instruction manual for the operating time and operation frequency. (Cause of accidents and trouble) Persons who use this product for the first time should use it while observing the condition of their skin. (Cause of skin trouble or poor physical condition) Do not use this product beyond the specified operating time. (Cause of skin trouble) Never insert or remove the power plug in/from the outlet with wet hands. (Cause of a failure or short circuit)

5 Use prohibited in wet areas Disassembly prohibited Prohibited Make sure Unplug This mark means that this appliance shall not be used near water contained in bath-tubs, basins or other vessels. Never wash this product with water. And, never soak in water or splash water on this product. (Cause of a failure or short circuit) Never use, charge or leave this product in places splashed with water or in damp places, such as in a bathroom. (Cause of a failure or short circuit) Never modify this product. Only a qualified technician may make repairs. (Cause of a fire, electric shock, injury, or failure) Check the head for any damage or deformation before use. (Cause of skin damage) Never use this product together with other beauty treatment devices at the same time. (Cause of a failure or trouble) Never use this product if there is some injury or wound to your skin. (Cause of skin trouble or pain) Do not drop this product, or give it a strong impact. (Cause of injury or a failure) Do not leave this product in a place where the temperature becomes high such as the inside of a vehicle. (Cause of failure) Do not wipe with benzene, thinner or alcohol, and do not spray insecticide. (Cause of cracking, an electric shock, or ignition) Use only the original power adaptor. And, do not charge any other product with the original power adaptor. (Possibility of an electric shock or ignition) Remove accessories such as earrings and necklaces, and contact lenses for use. (Cause of an accident or trouble) If there is any severe skin disorder or irregularity on your skin surface, or due to downy hair, you may feel strong irritation in rare instances. In this case, avoid using this product on that region. (Cause of an accident or trouble) Do not keep the cotton puff on one part of your skin but always keep it in motion. (Cause of skin trouble or poor physical condition) Pull out the power plug and device plug without holding the cord. (Cause of disconnection, an electric shock, short circuit, or ignition) When there are people around the device, pay attention to any sudden movement during use. (Cause of injury) Make sure to pull out the power plug from the outlet unless used. (Cause of an electric shock or fire by deterioration) Names of parts and their functions (Fig. 1) Preparation before use How to charge Head (titanium material) Attach cotton and apply it to the skin. The device vibrate while it is being used. Mode indicator lamp (orange) Turn the power switch "On," and "CLEANSING" will start flashing. Then, it switches and lights up while the device is being used. Mode switch button Every time the button is pressed, the mode for use will be switched. Power switch (" ") Turn on the power switch, and it will turn "On." Press it again, and it will turn "Off." An automatic shutoff function is equipped, so if the device is not used around 5 minutes, it will automatically turn "Off." Body Body socket Level indicator lamp LOW (green): MEDIUM (green): HIGH (red) When the power switch is switched to On, the lamp indicating HIGH, MEDIUM, or LOW is turned on. Do not use in places splashed with water, such as in a bath, or in damp places. (Cause of failures or short-circuits) 1. Turn off the switch, and connect the power adaptor to the main body and electric outlet. (Fig. 2) Charge indicator lamp During charge : The lamp turns on. (Red) After charging is completed : The lamp turns off. If the plug for the device's power adaptor is pushed in with force, or unnecessarily tilted, the main body socket may be broken. 2. After the standard charging time (5 hours) has elapsed, pull out the power adaptor from the electric outlet and the main body. (Fig. 3) The main body and the power adaptor become slightly hot, however, this is not unusual. Level switch button Every time the button is pressed, "the strength" of the electrical potential will change. There will be no change in vibration strength. Charge indicator lamp During charge : The lamp turns on. (Red) After charging is completed : The lamp turns off. Buzzer (Switching sound/warning sound/finish sound/indicating timer sound) Every time the switch or button is pressed, the switching sound will beep. If the warning sound beeps while the device is being used, this is an indication to recharge your batteries. When each mode is finished, the finish sound will beep. Back plate (titanium material) Batteries (built-in) Nickel hydride battery: 2 Power adaptor Model: KH-182B Power plug Instrument plug Cord Accessories Rings (two) Rings for attaching cotton. Stand Since this is not fully initially charged, charge before first using. Make sure to use only V and use the included power adaptor. Do not insert and remove the power plug from an electric outlet with wet hands. (Cause of electric shocks and short-circuits)

6 The standard charging time is 5 hours. The device can be used approximately 10 times on a single charge. (1 time means that all modes are being used once at High level.) Depending on the operating conditions such as the ambient temperature, operating times may decrease. Time to charge When the power is ON, if a warning sound can be heard, it is a signal to indicate recharging. Charge as soon as possible. In order to make full use of battery performance, observe the following. 1. If you have not used this product for three months or longer, charge before use. 2. Do not charge every time you use this product. 3. Charge at an ambient temperature between 10 and 35C. 4. Do not charge at an out-of-home power source, such as in a car or on board a ship. Preparation before use Never use the device when you have a wound or an inflammation on your skin. (Cause of problems with or damage to your skin.) Remove jewelry or contact lenses. (Cause of problems with your skin or poor health) 1. About mode switching Mode CLEANSING (cleans fine residue remaining in pores) MOISTURIZE (performs moisturizing care by allowing moisturizing ingredients to penetrate into skin) MASK (enhances the effect of milky lotion or sheet mask) Materials needed Use new cotton saturated with your regular toner. Use new cotton saturated with your regular toner. If you use a gel-like or thick toner, you can also apply it to head without using cotton. Use your regular milky lotion or a sheet mask by applying to skin. Do not use cotton. 2. Clean skin by washing your face so that makeup and dirt will wash off. Wipe off makeup with a cleansing product. 3. Attach cotton to the body of the device. (Fig. 4) The narrower side should be upward. Cotton (1)Remove the protection seal from the head. Unless the protection seal is removed, the device will not operate. (2)Place cotton over the head and attach it with the included ring. Use commercially available cotton. However, small cotton or thick cotton may not work in some cases. The ring has an orientation with a clear direction. Attach it from straight above with the wider part of the inner circumference placed toward the head. Do not attach the ring in the reverse direction. Please be careful not to squeeze it, otherwise, it cannot be removed. 4. How to remove the ring.(fig. 5) Remove the ring by pulling it straight up while holding down the lower part. 5. Please observe the following so as not to damage your skin when you use the device. (1) The maximum amount of time allowed for skin care with use of this device is approximate 10 minutes per day in basic mode. (Limit use of each step to no more than 5 minutes per day.) Basic mode Step 1 Step 2 Step 3 "CLEANSING" <Automatic shutoff> (approximate 5 minutes) "MOISTURIZE" <Automatic shutoff> (approximate 5 minutes) "MASK" <Automatic shutoff> (approximate 5 minutes) enhances the effect of milky lotion or sheet mask Limit use of the device to no more than 15 minutes per day including use of "Mask." It is recommended that you use Mask once or twice a week. (2) Use the device on bare skin after removing makeup. (3) Do not use the device on the same area of skin for more than 10 seconds. (4) Switch between high and low by pressing the Level switch button according to the condition of your skin. You can choose HIGH, MEDIUM, and LOW as you like. If your skin tingles, use the device on "LOW." If you feel something unusual with your skin, stop using the device and consult a skin care specialist. The device is equipped with a memory function to memorize the levels of HIGH, MEDIUM, and LOW that you would normally use. For details, please see About memory function. Examples of use Press the mode switch button and set the mode of your preferred treatment. Quick treatment (Required time: approximate 5 minutes) Step 2 "MOISTURIZE" When you do not have much time in the morning or when you need to go out suddenly, you can just use the "MOISTURIZE." That will moisturize your skin in approximate 5 minutes. Press the mode switch button and set to "Moisturize." Moisturize treatment (Required time: approximate 10 minutes) Step 1 "CLEANSING" Step 2 "MOISTURIZE" Before you go out or when you have more time, use the "MOISTURIZE" after using "CLEANSING." This will moisturize your skin thoroughly. Daily treatment (Required time: approximate 15 minutes) Step 1 "CLEANSING" Step 2 "MOISTURIZE" Step 3 "MASK" (milky lotion) Standard daily treatment. Fine vibration in Mask mode and gentle switching of the electrode will enhance the moisturizing effect of lotion.

7 Weekly treatment (Required time: approximate 15 minutes) Step 1 "CLEANSING" Step 2 "MOISTURIZE" Step 3 "MASK" (use of sheet mask) Care for the skin thoroughly once or twice a week in Mask mode using a commercially available sheet mask. How to use Step 1 "CLEANSING" This mode removes fine residue remaining in pores which cannot be removed by just washing. 1. Saturate cotton attached to the body with toner after washing your face. Please use your regular toner or rubbing-off toner with an exfoliating effect. (Do not use milky lotion or a gel-like or thick toner.) Saturate the cotton with toner to the extent that toner permeates the back of the cotton. 2. Press the power switch. (Fig. 6) The level indicator lamp will be turned on, and "CLEANSING" on the mode indicator lamp will start flashing. If a lamp in another mode is flashing, press the mode switch button to switch to "CLEANSING. 3 Choose "the strength" of electrical potential with the Level switch button. Switch the "strength" with the level switch button according to the condition of your skin. Every time the level indicator button is pressed, the high, medium, and low of the electrical potential will be switched. There will be no change in vibration strength. The memory function memorizes the "strength" when the power has been shut off. It is recommended that when using the device for the first time or if you feel some discomfort, use the device in "Low." 4 Hold the device with your hand touching the back plate of the body. (Fig. 7) Make sure to hold the body with your hand touching the back plate. 5 Apply cotton to the skin and move the device slowly. (Fig. 8) The mode indicator lamp will switch and turn on, and the device will start to vibrate. The time for use is within approximate 5 minutes. CAUTION Do not use the product around eyes and ears. (Cause of accidents or bad physical condition) If you feel something is unusual with your skin or body while using the device, stop using it immediately and consult a skin care specialist. (Cause of accident or poor health) Some toner (just with mineral spring or water) may be difficult to bring out a good effect. Unless you apply the cotton to your skin while touching the back plate, the device will not vibrate. (skin sensing function) If the head is not vibrating, the device is not working. If you leave the device as it is for about 5 minutes without vibration, the device will automatically switch "Off." (Automatic shutoff function) Indicating timer function Skin care time is indicated by the buzzer beeping about every 75 seconds as a guide. [Example of skin care sequence] Divide the area from your face to décolletage into four zones as shown in the illustration. By moving the head in the order of décolletage, the whole area can be efficiently and uniformly cared for. Apply the cotton gently to the face and slowly move the device by sliding it from the center of the face to the outer side. Do not keep the cotton on the same area of skin, it is necessary to move it around. (Cause of problems with your skin or physical discomfort.) Add more toner when there is no moisture in the cotton or when the device is difficult to slide. Do not apply the device on the same area of skin for more than 10 seconds. If you feel your skin tingling by micro current while using the device, press the level switch button and switch to "Low." If you still feel your skin tingling, use the device by adding more toner. 6 After 5 minutes have elapsed, the device will automatically shut off. (Auto shutoff function) The finish sound (beep beep) will inform you. 7 Remove the ring and the cotton. Wipe off the surface of the head with a tissue. Do not use the cotton again once it is used. It might cause problems with your skin. Step 2 "MOISTURIZE" This mode cares for skin by allowing moisturizing ingredients of toner to permeate the skin. When using cotton 1 Attach new cotton to the body with the attachment ring. For attaching cotton, see Preparation before use. 2 Saturate the cotton with your regular toner. Do not use milky lotion or gel-like or thick toner. Saturate the cotton with lotion to the extent that lotion permeates the back of the cotton. 3 Press the power switch. (Fig. 9) The level indicator lamp will be turned on, and the "MOISTURIZE" on the mode indicator lamp will start flashing. When a lamp in another mode is flashing, press the mode switch button and switch the mode. When the "CLEANSING" mode is finished, press the power switch and the "MOISTURIZE" mode will automatically be set. 4 Choose "the strength" of electrical potential with the level switch button. Switch the "strength" with the Level switch button according to the condition of your skin. Every time the level switch button is pressed, the LOW, MEDIUM and HIGH in the electrical potential will be switched. There will be no change in vibration strength. The memory function memorizes the "strength" when the power has been shut off. It is recommended that when using the device for the first time or if you feel some discomfort, use the device in "LOW."

8 5 Hold the device with your hand touching the back plate of the body. (Fig. 7) Make sure to hold the body with your hand touching the back plate. 6 Apply cotton to the skin and move the device slowly. (Fig. 8) The mode indicator lamp will switch and turn on, and the device will start to vibrate. The time for use is within 5 minutes. CAUTION Unless you apply cotton puff to your skin while touching the back plate, the device will not vibrate. (skin sensing function) If the head is not vibrating, the device is not working. If you leave the device as it is for about 5 minutes without vibration, the device will automatically switch "Off." (Automatic shutoff function) Indicating timer function Skin care time is indicated by the buzzer beeping about every 75 seconds as a guide. [Example of skin care sequence] Divide the area from your face to décolletage into four zones as shown in the illustration. By moving the in the order of décolletage, the whole area can be efficiently and uniformly cared for. Apply the cotton gently to the face and slowly move the device by sliding it from the center of the face to the outer side. Do not keep the cotton on the same area of skin, it is necessary to move it around. (Cause of problems with your skin or physical discomfort.) Add more toner when there is no moisture in the cotton or when the device is difficult to slide. Do not apply the device on the same area of skin for more than 10 seconds. If you feel your skin tingling by micro current while using the device, press the Level switch button and switch to "Low." If you still feel your skin tingling, use the device by adding more toner. 7 After 5 minutes have elapsed, the device will automatically shut off. (Auto shutoff function) The finish sound (beep beep) will inform you. 8 Remove the ring and the cotton. Wipe off the surface of the head with a tissue. Do not use the cotton again once it is used. It might cause problems with your skin. When not using cotton If you use a gel-like toner/moisturizing product (all-in-one type toner for moisturizing) or thick toner which is difficult to permeate the cotton you can use this device without attaching cotton to the body. 1 Apply a gel-like moisturizing product or thick toner that you would normally use onto the head and smoothen it over the entire head with your fingers. (Fig. 10) Moisturizing product 2 Press the power switch. (Fig. 9) The Level indicator lamp will be turned on, and the "Moisturize" on the mode indicator lamp will start flashing. When a lamp in another mode is flashing, press the mode switch button and switch the mode. When the "CLEANSING" mode is finished, press the power switch and the "MOISTURIZE" mode will automatically be set. 3 Choose "the strength" of electrical potential with the Level switch button. Switch the "strength" with the Level switch button according to the condition of your skin. Every time the level switch button is pressed, the high and low in the electrical potential will be switched. There will be no change in vibration strength. The memory function memorizes the "strength" when the power has been shut off. It is recommended that when using the device for the first time or if you feel some discomfort, use the device in "Low." 4 Hold the device with your hand touching the back plate of the body. (Fig. 7) Make sure to hold the body with your hand touching the back plate. 5 Apply the head directly to the skin and move it slowly. (Fig. 8) The mode indicator lamp will switch and turn on, and the device will start to vibrate. The time for use is within 5 minutes. CAUTION Unless you apply the head to your skin while touching the back plate, the device will not vibrate. (skin sensing function) If the head is not vibrating, the device is not working. If you leave the device as it is for about 5 minutes without vibration, the device will automatically switch "Off." (Automatic shutoff function) Indicating timer function Skin care time is indicated by the buzzer beeping about every 75 seconds as a guide. [Example of skin care sequence] Divide the area from your face to décolletage into four zones as shown in the illustration. By moving the head in the order of décolletage, the whole area can be efficiently and uniformly cared for. Add more toner or other moisturizing product when the head does not easily slide. Apply the cotton gently to the face and slowly move the device by sliding it from the center of the face to the outer side. Do not apply the device on the same area of skin for more than 10 seconds. If you feel your skin tingling by micro current while using the device, press the Level switch button and switch to "Low." If you still feel your skin tingling, use the device by adding more toner or other cosmetics. 6 After 5 minutes have elapsed, the device will automatically shut off. (Auto shutoff function) Do not keep the head on the same area of skin, it is necessary to move it around. (Cause of problems with your skin or physical discomfort.) The finish sound (beep beep) will inform you. 7 Wipe off the moisturizing product on the head and the body of the device with a tissue. Step 3 "MASK" (It is recommended that you use Mask once a day for milky lotion or moisturizing product once or twice a week for sheet mask.) Fine vibrations and gentle switching of the electrode enhance the effect of milky lotion or sheet mask.

9 1 Place the sheet mask on your face or apply your regular milky lotion or moisturizing product over your face evenly. Wipe off the milky lotion or moisturizing product on your hands. 2 Press the power switch. (Fig. 11) The level indicator lamp will be turned on, and the "Mask" on the mode indicator lamp will start flashing. When a lamp in another mode is flashing, press the mode switch button and switch the mode. When the "MOISTURIZE" mode is finished, press the power switch and the "MASK" mode will automatically be set. 3 Choose "the strength" of electrical potential with the Level switch button. Switch the "strength" with the Level switch button according to the condition of your skin. Every time the Level switch button is pressed, the high and low in the electrical potential will be switched. There will be no change in vibration strength. The memory function memorizes the "strength" when the power has been shut off. 4 Hold the device with your hand touching the back plate of the body. (Fig. 7) Make sure to hold the body with your hand touching the back plate. 5 Apply and move the head slowly. (Fig. 8) When using a sheet mask, slide the head over the sheet mask. The mode indicator lamp will switch and turn on, and the device will start to vibrate. The time for use is within 5 minutes. It is recommended that when using the device for the first time or if you feel some discomfort, use the device in "LOW." CAUTION Unless you apply the head to your skin while touching the back plate, the device will not vibrate. (skin sensing function) If the head is not vibrating, the device is not working. If you leave the device as it is for about 5 minutes without vibration, the device will automatically switch "Off." (Automatic shutoff function) Indicating timer function Skin care time is indicated by the buzzer beeping about every 75 seconds as a guide. [Example of skin care sequence] Divide the area from your face to décolletage into four zones as shown in the illustration. By moving the head in the order of décolletage, the whole area can be efficiently and uniformly cared for. Apply the head gently to the face and slowly move the device by sliding it from the center of the face to the outer side. Do not keep the head on the same area of skin, it is necessary to move it around. (Cause of problems with your skin or physical discomfort.) Do not apply the device on the same area of skin for more than 10 seconds. If you feel your skin tingling by micro current while using the device, press the level switch button and switch to "Low." 6 After 5 minutes have elapsed, the device will automatically shut off. (Auto shutoff function) The finish sound (beep beep) will inform you. 7 Wipe off the moisturizing product on the head and the body of the device with a tissue. How to use with AC 1 Connect the power adaptor to the main body and outlet. Follow "How to use" for use. While the device is being used, the battery indicator lamp will be off. 2 Make sure to pull out the power adaptor from the outlet and the body. About skin sensing function This device is a product which operates through the human body. Applying the skin to the back plate and the head will make an electrical circuit start to operate. Unless you touch the back plate and apply the head to the skin, it will not start to operate. About memory function This device is equipped with a memory function to store memory of the electrical potential "strength" levels of HIGH, MEDIUM, or LOW. In each usage mode (Step 1 to 3), the device stores memory of the "strength" level just before the automatic shutoff or the power switch is turned "off." If the level switch button is pressed while the device is being used, the electric potential "strength" can be switched. Care for main body Wipe off the toner/moisturizing product on the head and the body with a tissue. When dirt is difficult to remove, wipe it off with a cloth after saturating it with water and wring it thoroughly. CAUTION Do not use alcohol, benzine, or thinner. (Cause of deformation or discoloration) How to preserve Store the device on the included stand in a place free from excessive humidity or dirt. The stand can store the rings in it as well as put the body on it. (Fig. 12) CAUTION Avoid using in a place where water is splashed such as a bathroom or in a place with high moisture. (Cause of electric shocks and short circuits) Do not clean the main body with water. Or do not dip in water, and do not pour water. (Cause of failure) Make sure to turn OFF the switch. (Improperly turning on the switch may give a tingling sensation or result in malfunction or short-circuit.) Do not leave in a water splashing area or an area with significant humidity, such as a bath. (Cause of short-circuits or failure) Do not leave in an area subject to direct sunlight (inside of a vehicle in summer, etc.) or near heaters. (Cause of deformation or discoloration)

10 Specifications Rated voltage Rated power input Power consumption Battery Charging time Rated time Mass Accessories V AC, common to 50-60Hz 2W Power adaptor : KH-182B) Approximate 1.2WWhen it is charged at AC100V) Nickel-hydrogen battery (1.2V DC, 750mAh) Rated Capacity : 500mAh (When you charge 5 hours) 5 hours (Room temperature 10 ~ 35 Around 15 minutes at the maximum (basic mode:approximate 10 minutes) Main body : Approximately 85g Power adaptor : Approximately 65g Rings (two), Stand Attention for Use NOTICE Make sure to hold the main body of the product with your hand touching back plate and apply the head of the product to your skin. Otherwise, the product will not be operated. Back plate Disposal of the product Do not disassemble except when disposing of the product. This product includes recyclable parts. For disposal of the parts, observe your local laws and regulations etc. How to remove the nickel-hydrogen batteries 1. Keep pressing the power switch continuously while it is "ON" for about 10 seconds or more to make the device vibrate and leave it until the vibration stops. 2. Remove the two screws on the reverse side of the main body. (Fig. 13) Screws 3. Insert a flat-blade screwdriver or the like in the gap between the main body cases (front) and (rear), and remove the main body case (rear). (Fig. 14) Flat-blade screwdriver Main body case (rear) 4. Cut the lead wires connected to the terminals of the nickel-hydrogen batteries near the terminals, and take out the batteries from the battery holder. (Fig. 15) Main body case (front) Lead wires Nickel-hydrogen batteries Battery holder Do not allow the (+) and (-) terminals of the removed nickel-hydrogen batteries to make contact. (Cause of a short circuit or burns) About Skin Sensing Function This product which is operated through the human body. The electric circuit operates with skin in contact with the back plate and the head of the product. About Operating Time The continuous operating time of each mode is default. The time is not included under below circumstances: When the head or the head attached with cotton puff and back plate are not contacted with skin continuously The cotton puff used does not contain enough toner The actual operating time normally would be longer. About Auto-off Function If the product is not in operation around 5 minutes, the power will turn off automatically. There is an ending sound given and the product will turn off automatically when each mode is completed.

11 FAQs No. Questions Answers Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Tingling sensation is felt on the skin. Can "CLEANSING" mode remove makeup? Will dirt be more easily removed by applying more force? Cotton pad cannot be attached properly. Can the product be used in the bathroom? Check the intensity level. If it is set on "High" level, press the level switch button to switch to "LOW" level. If toner in the cotton pad wears off, replenish it again. If you still feel uncomfortable on the skin, stop using the product immediately and consult a dermatologist. This product cannot remove makeup. Please use a makeup remover cleanser. Electric power is used for removing dirt and moisturizing. Thus, by applying more force, it will not make any difference. Gently apply to skin and massage slowly. Use a normal rectangular or round cosmetic cotton pad. (If the cotton pad is too thick or thin, it will not be able to attach.) This product is not waterproof. Never use or place this product in wet and damp areas, e.g. bathroom. Can I use milky lotion or gel? Milk-based lotion or gel can be used when using MOISTURIZE mode without cotton and MASK mode. Please refer to the "About mode switching" in the "Preparation before use" section in the instruction manual for details. Does this product have whitening or blemish removal function? Which regions are not suitable to use this product? This product is not for whitening or removing blemish. It will pull out fine dirt that remains deep in the pores and penetrate moisture into the skin. Please refer to the instruction manual for the list of regions.

12

13

14

15

16

17

18 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8