ENGLISH General description (Fig. 1) A Spray nozzle B Filling opening C Spray button T D Steam control O = no steam q = moderate steam w = maximum ste

Size: px

Start display at page:

Download "ENGLISH General description (Fig. 1) A Spray nozzle B Filling opening C Spray button T D Steam control O = no steam q = moderate steam w = maximum ste"

比衡毛
5 years ago
Views:

1 Comfort LongLife GC1630 GC1621 GC1620 GC1615 GC

2 ENGLISH General description (Fig. 1) A Spray nozzle B Filling opening C Spray button T D Steam control O = no steam q = moderate steam w = maximum steam x = CalcClean E Extrasteam F Electronic safety shutoff (GC1630 only) G Temperature dial H Temperature light I Mains cord J Type plate K Anticalc tablet L tank Important Read these instructions for use carefully before using the appliance and save them for future reference. Check if the voltage indicated on the type plate corresponds to the local mains voltage before you connect the appliance. If the appliance is provided with an earthed plug it must be plugged into an earthed wall socket. Do not use the appliance if the plug the cord or the appliance itself shows visible damage or if the appliance has been dropped or is leaking. Check the cord regularly for possible damage. If the mains cord is damaged it must be replaced by Philips a service centre authorised by Philips or similarly qualified persons in order to avoid a hazard. Never leave the appliance unattended when it is connected to the mains. Never immerse the iron and the stand if provided in water. This appliance is not intended for use by persons (including children) with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. The of the iron can become extremely hot and may cause burns if touched. Do not allow the cord to come into contact with the when it is hot. When you have finished ironing when you clean the appliance when you fill or empty the water tank and also when you leave the iron even for a short while: set the steam control to position O put the and remove the mains plug wall socket. Always place and use the iron and the stand if provided on a stable level and horizontal surface. Do not put perfume vinegar starch descaling agents ironing aids or other chemicals in the This appliance is intended for household use only. Electromagnetic fields (EMF) This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual the appliance is safe to use based on scientific evidence available today. Before first use 1 Remove any sticker or protective foil from the. 2 Let the iron heat up to maximum temperature and pass the iron over a piece of damp cloth for several minutes to remove any residues. Note: may give off some smoke when you use it for the first time. This will cease after a short while. Preparing for use Filling the water tank Never immerse the iron in water. 1 Make sure the appliance is unplugged. 2 Set the steam control to position O (= no steam) (Fig. 2). 3 Tilt the iron backwards. 4 tank with tap water up to the maximum level. (Fig. 3) Do not fill the tank beyond the MAX indication. If the tap water in your area is very hard we advise you to mix it with an equal amount of distilled water or to use distilled water only. Do not put perfume vinegar starch descaling agents ironing additives chemically descaled water or other chemicals in the Setting the temperature 1 Put the. 2 Set the required ironing temperature by turning the temperature dial to the appropriate position (Fig. 4). Check the laundry care label for the required ironing temperature: 1 Synthetic fabrics (e.g. acrylic nylon polyamide polyester) 1 Silk 2 Wool 3 Cotton linen If you do not know what kind(s) of fabric(s) an article is made of determine the right ironing temperature by ironing a part that will not be visible when you wear or use the article. Silk woollen and synthetic materials: iron the reverse side of the fabric to prevent shiny patches. Avoid using the spray to prevent stains. Start ironing the articles that require the lowest ironing temperature such as those made of synthetic fibres. 3 Put the mains plug in an earthed wall socket. 4 When the gone out wait a while before you start ironing (Fig. 5). The temperature light will go on from time to time during ironing. Using the appliance Steam ironing 1 Make sure that there is enough 2 Select the recommended ironing temperature (see chapter Preparing for use section Setting the temperature ). 3 After the gone out set the steam control to the appropriate steam position. Make sure that the steam setting you select is suitable for the ironing temperature selected: (Fig. 6) q for moderate steam (temperature settings 2 to MAX) w for maximum steam (temperature settings 3 to MAX) Note: will start steaming as soon as the set temperature has been reached. Ironing without steam 1 Set the steam control to position O (= no steam). 2 Select the recommended ironing temperature (see chapter Preparing for use section Setting the temperature ). Features Spray You can use the spray to remove stubborn creases at any temperature. 1 Make sure that there is enough 2 Press the spray button several times to moisten the article to be ironed (Fig. 7). Extra steam This provides extra steam to remove very stubborn creases. The extrasteam only works at temperature settings between 3 and MAX. 1 Set the steam control to position w (= maximum steam). (Fig. 8) 2 Press and hold the steam control for a maximum of 5 seconds (Fig. 9). 3 Release the steam control and wait at least 1 minute before using this again to prevent water from dripping out of the. Electronic safety shutoff (GC1630 only) The electronic safety shutoff automatically switches off the iron if it has not been moved for a while. The autooff light starts blinking to indicate that the iron has been switched off by the safety shutoff (Fig. 10). In horizontal position this will happen after 30 seconds. In vertical position this will happen after 8 minutes. To let the iron heat up again: Pick up the iron or move it slightly. The autooff light goes out and the temperature light goes on. When the gone out and goes on again the iron is ready for use. Cleaning and maintenance After ironing 1 Remove the mains plug wall socket and let the iron cool down. 2 Wipe scale and any other deposits off the with a damp cloth and a nonabrasive (liquid) cleaning agent. To keep the smooth you should avoid hard contact with metal objects. Never use a scouring pad vinegar or other chemicals to clean the. 3 Clean the upper part of the iron with a damp cloth /5

3 4 Regularly rinse the water tank with water. Empty the water tank after cleaning. DoubleActive Calc System 1 The anticalc tablet prevents scale from clogging the steam vents (Fig. 11). The anticalc tablet is constantly active and need replacement. 2 The CalcClean removes the scale particles (Fig. 12). CalcClean Use the CalcClean once every two weeks. If the water in your area is very hard (i.e. when flakes come out of the during ironing) you should use the CalcClean more frequently. 1 Set the steam control to position O. 2 dial to MAX. 3 tank to the maximum level. Do not pour vinegar or other descaling agents into the 4 Put the plug in the wall socket. 5 Unplug the iron when the temperature light has gone out. 6 Hold the iron over the sink and set the steam control to the CalcClean position x. (Fig. 13) 7 Pull the steam control slightly upwards and gently shake the iron until all tank has been used up. Steam and boiling water will come out of the. Scale (if any) will be flushed out. 8 After having used the CalcClean press the steam control back to its original position and set it to position O. Repeat the CalcClean process if the water coming out of the iron still contains scale particles. After the CalcClean process 1 Connect the iron to the mains to let the dry. 2 Unplug the iron when the light has gone out. 3 Move the iron gently over a piece of used cloth to remove any water stains that may have formed on the. 4 Let the iron cool down before you store it. Cleaning the steam control needle 1 Pull the steam control out of the appliance. (Fig. 12) 2 Use vinegar to remove scale if any needle (Fig. 14). Do not bend or damage the steam control needle. 3 Reinsert the steam control needle by placing the point of the needle exactly in the centre of the hole and by fitting the small projection on the side of the needle into the slot (Fig. 15). 4 Set the steam control to position O. Storage 1 Make sure the appliance is unplugged and set the steam control to position O. 2 Empty the water tank (Fig. 16). 3 Wind the mains cord round the cord storage facility. 4 Store the in a safe and dry place (Fig. 17). Environment Do not throw the appliance away with the normal household waste at the end of its life but hand it in at an official collection point for recycling. By doing this you will help to preserve the environment (Fig. 18). Guarantee & service If you need information or if you have a problem please visit the Philips website at or contact the Philips Customer Care Centre in your country (you will find its phone number in the worldwide guarantee leaflet). If there is no Customer Care Centre in your country turn to your local Philips dealer or contact the Service Department of Philips Domestic Appliances and Personal Care BV. Troubleshooting This chapter summarises the most common problems you could encounter with your iron. Please read the different sections for more details. If you are unable to solve the problem contact the Customer Care Centre in your country. Problem Cause Solution is plugged in but the is cold. produce any steam. The extrasteam work. a connection problem. The temperature dial has been set to MIN. The steam control has been set to position O. The safety shutoff switched the iron off. The steam control has not been pressed long Check the mains cord the plug and the wall socket. dial to the required temperature. Set the steam control to position q or w (see chapter Using the appliance ). Move the iron slightly to deactivate the safety shutoff. will start heating up again. suitable for steam ironing ( 2 to MAX). Put the gone out before you start ironing. Press and hold the steam control for a maximum of 5 seconds. Problem Cause Solution when the extrasteam is being used. The spray work. Flakes and impurities come out of the during ironing. during ironing. while the iron is cooling down or after it has been stored. The extrasteam been used too often in a short period. The extrasteam been used too often in a short period. You have been using hard water which has caused scale flakes to develop inside the. has been put in horizontal position while there is still water in the water tank. Wait at least 1 minute before using the extrasteam again. control dial to a temperature between 3 and MAX. Put the gone out. between 3 and MAX. Put the gone out. Wait at least 1 minute before using the extrasteam again (see chapter Features ). Use the CalcClean one or more times (see chapter Cleaning and maintenance ). suitable for steam ironing ( 2 to MAX). Put the gone out before you start ironing. Empty the water tank and set the steam control to position O before storing the iron (see chapter Storage ). Place the iron on its heel /5

4 简体中文一般说明 ( 图 1) A 喷雾嘴 B 加水口 C 喷雾按钮 T D 蒸汽控制 O = 无蒸汽 q = 中等蒸汽量 w = 最大蒸汽量 x = 除水垢功能 E 加强蒸汽功能 F 电子安全关熄功能 ( 仅限 GC1630) G 温度旋钮 H 温度指示灯 I 电源线 J 型号牌 K 防水垢片 L 水箱注意事项使用本产品前请仔细阅读本使用说明书并妥善保管以备日后参考连接产品电源前请检查型号铭牌所标示的电压与当地电源电压是否一致如果产品附带的是接地插头则必须将其插至接地线的插座如果插头电源线或产品本身已经明显损坏或产品曾坠落或出现渗漏请勿再使用定期检查电源线是否损坏如果电源软线损坏为避免危险必须由制造厂或其维修部或类似的专职人员来更换在电熨斗接通电源期间使用者不得离开切勿将熨斗或熨斗座 ( 如有提供 ) 浸入水中本产品不打算由肢体不健全感觉或精神上有障碍或缺乏相关经验和知识的人 ( 包括儿童 ) 使用除非有负责他们安全的人对他们使用本产品进行监督或指导应照看好儿童确保他们不玩耍本产品应照看好儿童确保他们不会玩弄本产品电熨斗的底板会变得非常烫如触摸底板可能会导致烫伤不要让电源线触及高温电熨斗底板当完成熨烫清洁产品注水或倒空水箱以及短时间离开熨斗时 : 请将蒸汽控制旋钮调至位置 O 竖放熨斗并从插座中拔下电源插头一定要在稳固平整且水平的表面上放置和使用熨斗及熨斗座 ( 如有提供 ) 不要将香水醋淀粉除垢剂烫衣剂或其它化学品放入水箱本产品仅限于家用电磁场 (EMF) 这款飞利浦产品符合关于电磁场 (EMF) 的相关标准据目前的科学证明如果正确使用并按照本用户手册中的说明进行操作本产品是安全的初次使用之前 1 从熨斗底板上取下任何标签或保护膜 2 将熨斗升温至最高温度用熨斗在一块湿布上熨烫几分钟以除去底板上的任何残留物注 : 首次使用时熨斗可能冒烟过一会就会停止使用准备给水箱注水切勿将熨斗浸入水中 1 确保熨斗的插头已经拔掉 2 将蒸汽控制旋钮调至位置 O(= 无蒸汽 ) ( 图 2) 3 将熨斗向后倾斜 4 将自来水加注到水箱的最高标志 ( 图 3) 切勿超过 MAX 最高水位标志如果您所在地区的自来水硬度很高我们建议您将自来水与等量的蒸馏水混合后再使用或仅使用蒸馏水不要将香水醋淀粉除垢剂烫衣剂或其他化学品放入水箱设定温度 1 将熨斗竖立 2 将温度转盘转到适当位置以设定所需熨烫温度 ( 图 4) 检查衣服标签以了解所需熨烫温度 : 1 合成纤维 ( 如聚丙烯尼龙聚酰胺聚脂 ) 1 丝绸 2 羊毛 3 棉亚麻如果您不知衣物是由何种纤维组成找一处穿着或使用时看不见的地方熨试试何种温度最合适真丝织品羊毛及合成纤维 : 要翻到内面熨烫以防发亮避免使用喷雾功能以免产生斑迹从需要最低熨烫温度的布料开始熨烫如合成纤维织物 3 将插头插入有接地的电源插座 4 如果温度指示灯亮着应等一会再开始熨烫 ( 图 5) 在熨烫期间温度指示灯会熄灭使用本产品蒸汽电熨斗 1 确保水箱中有足够的水 2 选择推荐的熨烫温度 ( 见使用准备一章中的设定温度一节 ) 3 温度指示灯熄灭之后将蒸汽控制旋钮设定到适当位置确保您所选定的熨烫温度适合所选温度 : ( 图 6) q 表示中等蒸汽量 ( 温度设定从 2 到最大 (MAX)) w 表示最大蒸汽量 ( 温度设定从 3 到最大 (MAX)) 注 : 只要达到设定的温度就立即开始喷出蒸汽无蒸汽熨烫 1 将蒸汽控制旋钮调至位置 O(= 无蒸汽 ) 2 选择推荐的熨烫温度 ( 见使用准备一章中的设定温度一节 ) 功能喷雾装置您可在任何温度下使用喷雾功能去除顽固褶皱 1 确保水箱中有足够的水 2 按几次喷雾按钮把要熨烫的布料弄湿 ( 图 7) 加强蒸汽此功能可产生加强蒸汽以去除顽固皱褶加强蒸汽功能只能在温度设定 3 到最高温度 (MAX) 之间工作 1 将蒸汽控制旋钮设定到 w 位置 (= 最大蒸汽 ) ( 图 8) 2 按住蒸汽控制旋钮长达 5 秒钟 ( 图 9) 3 放开蒸汽控制钮至少等 1 分钟后才能再次使用本功能以防水从底板滴出电子安全关熄功能 ( 仅限 GC1630) 如果熨斗在一段时间内没有移动电子自动安全关熄功能将自动切断熨斗电源自动关熄指示灯开始闪烁指示熨斗的电源已经被电子安全关熄功能关闭 ( 图 10) 在水平状态时 30 秒后会自动关熄在垂直状态时 8 分钟后会自动关熄让熨斗再次加热 : 将熨斗拿起或稍微动一下自动关熄指示灯熄灭温度指示灯亮起当温度指示灯熄灭再次亮起后熨斗即可使用清洁和保养熨烫后 1 从插座中拔下电源插头让熨斗充分冷却 2 用湿布和非腐蚀性 ( 液体 ) 清洁剂抹去底板上的水垢和其它沉积物为了保持底板光滑应避免底板与金属物体碰撞切勿使用磨砂布醋或其他化学品清洁底板 3 用湿布清洁熨斗的上部 4 定期用水冲洗水箱清洗之后将水箱中的水全部倒出双效除垢系统 1 防水垢片防止水垢堵塞蒸汽管 ( 图 11) 防水垢片持续有效无须更换 2 除垢功能可除去水垢颗粒 ( 图 12) 除水垢功能建议两周使用一次自动除垢功能如果您所在地区的水质很硬 ( 即在熨烫过程中底板出现水垢薄片时 ) 则应增加使用自动除垢功能的次数 1 将蒸汽控制旋钮设定到位置 O 2 将温度转盘调至最大 (MAX) 3 将水箱注满至最高水位 (MAX) 请勿将醋或其它除垢剂注入水箱 4 将插头插入插座 5 当温度指示灯熄灭时拔下熨斗的电源插头 6 在水池上方手持熨斗并将蒸汽控制旋钮设定到除水垢位置 x ( 图 13) 7 将蒸汽控制旋钮轻轻地向上拉然后柔和地摇动熨斗直到所有的水耗尽蒸汽和沸水会从底板冲出水垢 ( 如果有的话 ) 也一并冲出 8 使用完除水垢功能后将蒸汽控制旋钮按回原来的位置并设定到 O 位置如果从熨斗中冲出的水仍有水垢颗粒则应再次使用除水垢功能完成除水垢过程后 1 插上熨斗的插头让底板变干 2 当指示灯熄灭后将熨斗的插头拔下 3 将熨斗放在一块用过的布上轻轻地前后移动以除去留在底板上的水渍 4 让熨斗冷却然后存放好清洁蒸汽控制针 1 将蒸汽控制旋钮从熨斗中拉出 ( 图 12) /5

5 2 如果针上有水垢请使用醋将其除去 ( 图 14) 不要弄弯或损坏蒸汽控制针 3 重新插入蒸汽控制针方法是 : 将蒸汽控制针的针尖对准孔的中央让针侧面的凸缘插入槽内 ( 图 15) 4 将蒸汽控制旋钮设定到位置 O 存放 1 确保产品的插头已经拔掉且蒸汽控制旋钮已设定到位置 O 2 倒空水箱 ( 图 16) 3 将电源线绕在存线装置上 4 请将熨斗竖放在安全干燥的地方 ( 图 17) 环保弃置产品时请不要将其与一般生活垃圾堆放在一起 ; 应将其交给官方指定的回收中心这样做有利于环保 ( 图 18) 保修与服务如果您需要详细信息或有任何问题请浏览飞利浦网站地址为您也可以与贵国的飞利浦顾客服务中心联系 ( 您可以从全球保修卡中找到电话号码 ) 如果贵国没有飞利浦顾客服务中心请与当地的飞利浦经销商或与飞利浦家庭小电器的维修中心联系故障种类和处理方法本章归纳了您的熨斗在使用时最常遇到的问题有关详细说明请参阅相关章节如果您还不能解决问题请与贵国的飞利浦客户服务中心联系问题原因解决方法熨斗已经插好插头但底板仍是凉的熨斗没有蒸汽加强蒸汽功能不能工作接触不良温度转盘设在 MIN 水箱中水不足蒸汽控制设在 O 位置安全关熄功能将熨斗断电蒸汽控制旋钮按下的时间不够长加强蒸汽功能在短时间内使用过于频繁检查电源线插头和电源插座将温度转盘设定到所需温度将水箱注满水 ( 见使用准备一章 ) 将蒸汽控制旋钮设定到 q 或 w 位置 ( 见使用产品一章 ) 轻轻移动熨斗以便解除安全关熄功能熨斗将再次开始加热将温度转盘设定在一个适合蒸汽熨烫的温度 ( 2 到最大 ) 将熨斗竖立直到温度指示灯熄灭后再开始熨烫按住蒸汽控制旋钮长达 5 秒钟再次使用加强蒸汽功能之前至少等 1 分钟问题原因解决方法当使用加强蒸汽功能时有水从底板漏出喷雾功能不能工作在熨烫过程中底板内冒出水垢和杂质熨烫时水从底板漏出当熨斗冷却或存放后水从底板漏出水箱中水不足加强蒸汽功能在短时间内使用过于频繁水箱中水不足硬水在底板内形成水垢熨斗水平放置时水箱中还有水将温度控制旋钮调至 3 和最大 (MAX) 之间的某个温度将熨斗竖立直至温度指示灯熄灭后再开始熨烫将水箱注满水 ( 见使用准备一章 ) 将温度转盘在 3 与最大 (MAX) 之间设定一温度将熨斗竖立直到温度指示灯熄灭再次使用加强蒸汽功能之前至少等 1 分钟 ( 见功能一章 ) 将水箱注满水 ( 见使用准备一章 ) 使用一次或多次除垢功能 ( 见清洁和保养一章 ) 将温度转盘设定在一个适合蒸汽熨烫的温度 ( 2 到最大 ) 将熨斗竖立直到温度指示灯熄灭后再开始熨烫存放熨斗之前先将水箱倒空然后将蒸汽控制设定到 O 位置 ( 见存放一章 ) 将熨斗竖放 2006/12/ /5

K301Q-D VRT中英文说明书141009

K301Q-D VRT中英文说明书141009 THE INSTALLING INSTRUCTION FOR CONCEALED TANK Important instuction:.. Please confirm the structure and shape before installing the toilet bowl. Meanwhile measure the exact size H between outfall and infall