X4-一體尾殼V1.0.3.indd

Size: px

Start display at page:

Download "X4-一體尾殼V1.0.3.indd"

番阮
5 years ago
Views:

and even death. 本產品是無線遙控的直升機不當的操作, 保養或是組裝有可能導致遙控直升機對於人身或是物品造成危險 Recommendation: We highly suggest using the latest version of the Assembly Instruction Manual.

1 ASSEMBLY INSTRUCTION V1.0.3 This product is for a radio controlled (RC) helicopter. Improper operation, maintenance or assembly can potentially cause a RC helicopter to pose danger to persons or objects including but not limited to the possibility of causing serious physical injury and even death. 本產品是無線遙控的直升機不當的操作, 保養或是組裝有可能導致遙控直升機對於人身或是物品造成危險 Recommendation: We highly suggest using the latest version of the Assembly Instruction Manual. To download the latest version, please visit the Official TSH web site: 取得最新的手冊 : 我們非常建議您取得最新版本的手冊請到泰世網站下載最新的手冊, 並且取代目前的手冊 This product is suitable servo specifi cations (35mm x 15mm x 30mm). Cited the following servo for reference purposes only. 本產品伺服器適用規格 (35mm x 15mm x 30mm) 列舉下列伺服機, 僅供參考 CCPM: FUTABA: BLS153.BLS651.S9650 JR : DS3401.DS3405.DS3201.DS361.NES-3125 SAVOX : SH1350 RUDD: FUTABA: BLS257.S9257. SAVOX : SH1357.

2 3-3 Preface 前言 LIABILTY DISCLAIMER 免責聲明 Academy of Model Aeronautics (AMA) Tools and Equipment for Assembly 自備工具及設備 Symbols of Assembly Notices / Specification 組裝代號說明 Fuselage Assembly-1~2 機身組立 -1~2 Fuselage Assembly-3~4 機身組立 -3~4 Fuselage Assembly-5 / Motor Installation-1 機身組立 -5 / 馬達組立 -1 Motor Installation-2 / Main Drive Gear Assembly 馬達組立 -2 / 主齒盤組立 Servos Assembly-1~2 伺服機安裝 -1~2 Rotor Head Assembly / Washout Arm Assembly 主旋翼頭組裝 / 剪型臂組裝 Rotor Blade Grip Assembly / Motor Installation-1 旋翼夾頭組裝 / 前傳動組裝 Tail Rotor Assembly / Vertical Stablizer Assembly 尾殼總成組裝 / 垂直尾翼組裝 Tail Blade Grip Assembly / Tail Set Assembly 尾旋翼夾頭組裝 / 尾旋翼總成組裝 Tail Blades Assembly / Tail Boom Assembly 尾旋翼片組裝 / 尾管總成組立 Tail Boom Brace Assembly / Main Rotor Head Linkage Rod Assembly 支撐桿組裝 / 主旋翼拉桿組裝 Throttle Curve and Pitch Curve / Setting Pitch 螺距 & 油門曲線設定 / 主旋翼螺距設定 Parts 零件表 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 ~ P19

3 Preface 前言 Thank you for purchasing High Performance RC Helicopter from Tai Shih Hobby Corporation (TSH). We hope you will enjoy the joy of flight. 感謝您購買泰世科技出品的飛行的樂趣高性能遙控直升機, 我們希望您可以盡情享受 In order to understand full assembly sequences, this instruction manual show the assembly information of this model, even though some elements are supplied as pre-assembled. Please refer to it when carrying out maintenance or replacing parts. 為了要讓使用者詳細瞭解組裝順序, 即使有些部件已經預先組裝完成, 本說明書將提供這台遙控模型的組裝資訊同時, 敬請參閱保養與主要零件更換資訊 CAUTION: This radio controlled helicopter is not a toy. 警告 : 這台遙控直升機不是玩具 SAFETY PRECAUTIONS This kit includes some preassembled components. Please check for any loose screws and tighten them before you proceed with assembly. You are responsible for assembly, safe operation, maintenance, inspection and adjustment of the model. Before beginning assembly, please read these instructions thoroughly. Check all parts. If you find any defective or missing parts, contact your local dealer or TSH distributor. Before you proceed to RC helicopter activity, please check and follow thoroughly related regulation of aero modeling in your country/region. 安全資訊與注意事項這台遙控模型包含預先組合完成的部件在進行組裝之前, 請仔細檢查這些預先組裝部件上的所有螺絲均有仔細鎖緊您有完全的責任對於這台遙控模型的組裝, 安全操作, 保養, 檢查與調整請先檢查所有的零件, 如果發現任何不良品, 遺失品, 請向模型店或是當地的泰世代理商連絡在您進行遙控直升機活動時, 請先詳細瞭解與遵守當地遙控模型的相關法規 1

4 LIABILITY DISCLAIMER 免責聲明 LIABILITY DISCLAIMER This product is for a radio controlled (RC) helicopter. Improper operation, maintenance or assembly can potentially cause a RC helicopter to pose a danger to persons or objects including but not limited to the possibility of causing serious physical injury and even death. Moving components can present a hazard to operators, and anyone or anything that could be in the flying area of the RC helicopter. Under no circumstance should a minor be allowed to operate this RC helicopter without the approval, monitor and direction of his parent or legal guardian who takes full responsibility for all of the minor's actions. This product is intended for being operated by experienced mature radio control helicopter pilots under controlled safety conditions and on locations properly authorized and setup for safe flying and away from other people. Do not operate an RC helicopter within the vicinity of residences, trees, electrical power lines during inclement weather or near crowds of people. The manufacturer and/or its distributors assume no responsibility or liability whatsoever for any damages including but not limited to ones generated by incidental or consequential damages. The operator of the helicopter assumes all responsibility and liability that results from the correct or incorrect operation of the helicopter. After leaving its facilities, the manufacturer has no way of maintaining control or monitor over the assembly, maintenance and/or operation of the helicopter. 免責聲明本產品是無線遙控的直升機不當的操作, 保養或是組裝有可能導致遙控直升機對於人身或是物品造成危險包括, 但是不局限於對於人體產生嚴重傷害甚至死亡的可能性所有的移動部件可能對於操作的使用者, 旁人或是這台遙控直升機飛行場的任何人或物品產生傷害未成年的人如果要操作這台遙控直升機需要父母或是監護人的同意, 並在監督與指導下才能進行操作並遠離周遭障礙物及人群等, 其父母或是監護人需負起所有責任與法律責任以下場合與情況禁止操作遙控直升機 : 居家房屋附近天候不佳時非空曠區域樹木電線竿等場合或是人群附近製造廠商與其經銷商都不對於所有的傷害, 包含但是不局限於偶然或是連續發生的傷害負擔任何責任本產品的使用者要對於正確地或是不正確地操作的結果需負擔所有責任與法律責任本產品一但離開製造廠商的控制範圍外, 製造廠商無法對於下列事項保持監督與控管 : 組裝, 保養, 維修與操作這台遙控直升機 2

5 Academy of Model Aeronautics (AMA) For United States market, The Academy of Model Aeronautics (AMA) is a national organization representing modelers in the United States. Please refer the National Model Aircraft safety code from Academy of Model Aeronautics. And we ve partially reprinted rules that are especially pertinent for radio controlled flight as below: RADIO CONTROL 1. All pilots shall avoid flying models over unprotected people. 2. I will complete a successful radio equipment ground-range check in accordance with the manufacturer s recommendations before the first flight of a new or repaired aircraft. 3. At all flying sites a safety line or lines must be established, in front of which all flying takes place. Only personnel associated with flying the model aircraft are allowed at or in front of the safety line. In the case of air shows or demonstrations a straight safety line must be established. An area away from the safety line must be maintained for spectators. Intentional flying behind the safety line is prohibited. (See AMA Document #706 for Recommended Field Layout.) 4. I will operate my model aircraft using only radio-control frequencies currently allowed by the Federal Communications Commission (FCC). Only individuals properly licensed by the FCC are authorized to operate equipment on Amateur Band frequencies. 5. I will not knowingly operate my model aircraft within three (3) miles of any preexisting flying site without a frequency-management agreement. (See AMA Document #922 for Testing for RF Interference. See AMA Document #923 for Frequency Management Agreement.) 6. With the exception of events flown under official AMA Competition Regulations rules, excluding takeoff and landing, no powered model may be flown outdoors closer than 25 feet to any individual, except for the pilot and the pilot s helper(s) located at the flight line. 7. Under no circumstances may a pilot or other person touch a model aircraft in flight while it is still under power, except to divert it from striking an individual. This does not apply to model aircraft flown indoors. 8. Radio-controlled night flying requires a lighting system that provides the pilot with a clear view of the model s attitude and orientation at all times. 9. The operator of a radio-controlled model aircraft shall control it during the entire flight, maintaining visual contact without enhancement other than by corrective lenses that are prescribed for the pilot. First-Person View (FPV) flying may only be conducted in accordance with the procedures outlined in AMA Document #550. These special codes and appropriate documents may be obtained either from the AMA Web site at or by contacting AMA headquarter. Academy of Model Aeronautics 5151 East Memorial Drive Muncie, IN Phone (800) Fax (765)

6 Tools and Equipment for Assembly 自備工具及設備 2.0mm Hexagon Screw Driver 3.0mm Hexagon Screw Driver 2.5mm Hexagon Screw Driver 3.5mm Hexagon Screw Driver 2.0mm 六角螺絲起子 3.0mm 六角螺絲起子 2.5mm 六角螺絲起子 3.5mm 六角螺絲起子 Needle-nosed pliers Diagonal cutting plier Ball Link Plier Philips Screw Driver 尖嘴鉗斜口鉗拔豆鉗十字螺絲起子 Scissors Dial Pitch Gauge CA Thread Lock 剪刀主旋翼螺距規瞬間膠螺絲止鬆劑 CCPM Servo x3pcs(35x15x30) Tail Specialized Servo x1pcs(35x15x30) Battery 3-Axis Stabilizer CCPM 伺服機 x3 個尾舵伺服機 x1 個鋰聚電池 3 軸陀螺儀 Transmitter (6-channel or more, helicoper system) 六動以上接收機 & 發射機 Lubricant 潤滑油 4

7 Symbols of Assembly Notices 組裝代號說明 Apply general thread lock. To tight screw and apply thread lock. 一般型止鬆劑鎖緊螺絲並確認上膠 Apply general thread lock. Be certain to tighten screw and apply thread lock. 一般型止鬆劑務必鎖緊螺絲並確認上膠 Apply CA glue 使用瞬間黏著劑 Apply anaerobic adhesive. Tighten screw and apply thread lock. 特殊型止鬆劑鎖緊螺絲並確認上膠 Apply anaerobic adhesive. Be certain to tighten screw and apply thread lock. 特殊型止鬆劑務必鎖緊螺絲並確認上膠 Apply lubricant 依個人需求使用潤滑油 Attention: Pay attention, care should be taken during assembly. 注意 : 組裝過程中請注意並小心安裝 Extreme attention: More attention should be taken during assembly. Double check after assembly. 非常注意 : 組裝過程中請非常注意並小心安裝及再確認組裝無誤 Danger: High level of attention should be taken during assembly. Action during assembly might be hazardous. Extreme care should be taken to avoid injury. 危險 : 組裝過程中請小心安裝並注意此危險程度可能造成安全性漏洞導致人為傷害 Apply special thread lock 使用特殊型止鬆劑 Smaller inner race 內徑較小 (S) (L) 內徑較大 Bigger inner race Smaller inner race 內徑較小 (S) (L) 內徑較大 Bigger inner race B-Bearing B- 軸承 Ø-TapScrew Ø- 粗牙螺絲 M-Machine Screw M- 公制螺絲 P-tube P- 柱狀體 Pillar P- 柱狀體 N-Nut N- 螺母 W-Washer W- 華司 B(Dia.in)x(Dia.out)x(Thickness) B( 內徑 )X( 外徑 )X( 厚度 ) Ø(Dia.out)x(Length) Ø( 外徑 )X( 長度 ) M(Dia.out)x(Length) M( 外徑 )X( 長度 ) P(Dia.in)x(Dia.out)x(Length) P( 內徑 )X( 外徑 )X( 長度 ) P(Dia.out)x(Length) P( 外徑 )X( 長度 )X( 實心柱 ) N(Dia.in)x(Width) L-Lock nut N( 外徑 )X( 長度 ) W(Dia.in)xDia.out)x(Thickness) W( 內徑 )X( 外徑 )X( 厚度 ) Make sure to assemble the parts as shown in figure above. Incomplete or incorrect assembly may cause control failure during flight. 以上圖示, 於組裝時請確實注意, 避免組裝後試飛造成失控零件鬆脫等情況發生 Specification 規格資料 Gear Ratio 齒輪傳動比 : : 1 : 4.06 (E.M.T) Overall Length (with Canopy):880 Specifications 機身長度 ( 含艙罩 ):880 mm Main Rotor Diameter:970mm 主旋翼迴轉直徑 :970 mm Main rotor blades:425mm 主旋翼長度 :425mm Overall Height:284mm 機身高度 :284 mm Overall Width:165mm 機身寬度 :165 mm Tail Blade Length:70mm 尾旋翼葉片長度 :70 mm Tail Rotor Diameter:140mm 尾旋翼迴轉直徑 :140 mm Motor Drive Gear:18T 馬達齒 :18T Main Drive Gear: 61T 主齒輪 :61T Flying duration: 4~5 minutes 飛行時間 :4~5 分鐘 Power System(Recommanded): Motor ~1400KV ESC 66A~100A ESC 6S1P(22.2v/2100~3000mah) 動力系統 ( 原廠建議 ): 馬達 1300~1400KV 電子變速器 66A~100A ESC 使用鋰聚電池 :6S1P(22.2v / 2100~3000mah) Total weight: 1400g ±5% (Equipped with Blades and 全配重量 :1400g ±5% ( 全套含電子裝備不含電池 ) all electronic gears except Battery). This product is for a radio controlled (RC) helicopter. Improper operation, maintenance or assembly can potentially cause a RC helicopter to pose a danger to persons or objects including but not limited to the possibility of causing serious physical injury and even death. 本產品是無線遙控的直升機不當的操作, 保養或是組裝有可能導致遙控直升機對於人身或是物品造成危險 Important: The gear ratio, motor and battery should be set properly if the power system has been changed!!! 注意 : 更改動力系統請注意電池電壓, 馬達 KV 值及減速比的關係來做搭配 5

8 Fuselage Assembly-1 機身組立 -1 Assemble the one way gear and shaft, then tighten the M3x3 set screws onto the one way shaft. 組合單向齒軸及單向齒, 之後再將 M3x3 鎖附於單向齒軸上 B8x16x5 61T M3x3 M3x5 P8.1x9.6x5.3 M2x8 B8x12x3.5 W8x10.5x0.5 單向齒 One Way Gear(19T) W8x10.5x0.5 B8x12x3.5 W3x9x1 B8x16x5 M3x6 Fixing end for screws 固定點單向齒軸 One Way Gear Shaft 齒輪 (15T) Gear(15T) B5x11x4 B5x11x4 Fuselage Assembly-2 機身組立 -2 1.Install the Reduction Gear Unit to the Frames, assemble other parts as shown in figure. 1. 承上頁將組裝好的齒輪組組裝至右側板上並依序組裝 M3x12 M3x4 M3x6 13pcs 6

9 Fuselage Assembly-3 機身組立 -3 1.Install the Reduction Gear Unit to the Frames, assemble other parts as shown in figure. 2.Do not tighten those M3x18 screws until the tail boom is installed and the gear mesh is set properly. 1. 承上頁將左側板組裝至機身 2.M3x18 螺絲含上待 P.15 頁組裝時在鎖緊 M3x4 M3x12 M3x18 M3x6 12pcs Fuselage Assembly-4 機身組立 -4 Attach the Cuboid Posts to Front / Bottom / Rear plates, then assemble those plates and Main frame set as shown in figure. 建議可先將側板鋁柱固定於 3 片隔板, 再連同側板與鋁柱一起鎖緊 M3x6 7pcs M3x6 12pcs 7

10 Fuselage Assembly-5 機身組立 -5 1.Assemble the landing skid and skid pipe to the main frame. 1. 將腳架及滑橇組裝至機身 M3x3 4pcs M3x14 2pcs Motor Installation-1 馬達組立 Fix the motor to the motor mount with M3x6 screws (not tighten yet). 2.Tighten the screws and fix the motor. ( Keep them at a proper distance about 7mm). 1. 使用 M3x6 螺絲將馬達固定在馬達座上 ( 先不鎖緊 ) 2. 鎖緊馬達齒 ( 間距約 7mm) B5x11x4 M3x3 2pcs M3x6 2pcs 7mm 8

11 Motor Installation-2 馬達組立 Adjust the gear mesh of the motor pinion and front drive gear to approximately 0.1mm. 2.Fix the motor set with M3x6 screws. 1. 調整馬達齒與前齒輪間隙 ( 約 0.1mm) 2. 取出馬達座總承將 P8. M3x6 螺絲鎖緊, 固定馬達 3. 將馬達總成置入機身並使用 M3x6 螺絲固定 gear mesh adjustment 間隙調整 M3x6 4pcs Main Drive Gear Assembly 主齒盤組立 1.Insert the main shaft through main drive gear, fixing with M3x16 screws. 2.Pull the main shaft and fixing the collar with M3x3 screws. 1. 將主軸置入機身並連同主齒盤組裝, 鎖緊 M3x16 螺絲 2. 將主軸上提至底並將主軸輪檔下移靠緊主軸座, 鎖緊 M3x3 螺絲 (Fig.1) W8x11x2 TOP M3x16 Fig.1 N3x5.5L M3x3 9

12 Servos Assembly-1 伺服機安裝 Assemble the servos spare parts, make sure the mounting blocks are assembled correctly. 2.Install the servos to the frame, fixing with M3x6, M3x14 screws. 1. 組裝伺服器並確認伺服器鋁柱位置無誤 2. 將組裝好的伺服機總成, 從側邊裝入機身並鎖緊 M3x6,M3x14 螺絲 M3x14 2pcs M3x8 6pcs M2x12 2pcs 伺服器鋁柱 Mounting block M3x6 2pcs Servos Assembly-2 伺服機安裝 Install the servos to the frame. 1. 組裝伺服器 M3x8 4pcs M3x8 4pcs 10

13 Rotor Head Assembly 主旋翼頭組裝 1. Assemble the main rotor head, fixing the M3x16 screw. 1. 組裝主旋翼頭並鎖緊 M3x16 Idle: 95 Damper rubber Normal: 75 Damper rubber 特技飛行 O-ring 95 一般飛行 O-ring 75 The default setting of damper rubber is 75, and 95 damper rubber (#213220) for optional. O-ring 原廠設定硬度為 75 另有 #213220( 硬度 95 ) 可選購 M3x16 N3x5.5L Washout Arm Assembly 剪型臂組裝 1.Assemble the washout arm, and fixing it to the main rotor head. 1. 將兩組剪型臂組裝至主旋翼頭 M3x10 P2x13 W3.1x4.6x0.6 B3x6x2.5 W3.1x4.6x0.6 B3x6x2.5 11

14 Rotor Blade Grip Assembly 旋翼夾頭組裝 1.Assemble the rotor blade grip. 2.Fix the main grip levers with M3x16 screws. 3.Install the stop plate. 1. 將主旋翼夾頭組裝至主旋翼頭 2. 鎖上主旋翼舵柄 3. 鎖上煞車盤 Apply thread lock on all screws in this section. 螺絲均需上止滑劑 Stop Plate 煞車盤 M3x10 W6.2x7.6x0.5 W4.1x10x1.4 B6x13x3.5 T6x12x4.5 M3x6 M4x10 B6x13x5 W6.1x10x1.5 Main Grip Levers 主旋翼舵柄 Tail Boom Assembly 前傳動組裝 1.Assemble the tail support clamp and tail control rod, insert the front drive gear into the tail boom. 1. 將尾管夾及拉桿座置入尾管, 並套上前傳動齒輪箱 M3x6 2pcs 拉桿座 Rudder Control Guide 前傳動齒輪箱 Front Drive Gear 尾管夾 Tail Support Clamp 尾舵拉桿 Tail Control Rod 12

15 Assembly of Tail Gear Box 尾殼總成組裝 1.Fix the M2x8 screw into the bevel gear, and fix the M2x8 screw with M3x3 screw. 1. 將 M2x8 螺絲鎖入齒軸並將 M3x3 螺絲鎖入尾軸, 固定 M2x8 Apply thread lock on all screws in this section. 螺絲均需上止滑劑 B12x18x4 M3x6 N3x5.5L Fixing end for screws定位孔 M3x3 M3x6 M3x6 M3x6 B5x11x4 B5x11x4 M2x8 M3x12 Fixing end for screws 固定點 Assembly of Tail Vertical Stablizer 垂直尾翼組裝 Apply thread lock on all screws in this section. 螺絲均需上止滑劑 M3x12 M3x12 13

16 Assembly of Tail Blade Grip 尾旋翼夾頭組裝 B4x9x4 T3x8x3.5 W3.1x4.6x0.6 N2.5x5L B3x8x3 Assemblly of Tail Rotor Set 尾旋翼總成組裝 1.Assemble the tail rotor set. 2.Please make sure the tail blade grip work smoothly while fixing the M2x10 screws. 1. 組裝尾翼總成 2.M2x10 螺絲鎖緊時請確認尾旋翼夾頭運作順暢 M2x10 P2x2.95x4.5 M3x3 Fixing end for screws 固定點 B4x7x2.5 M3x3 P2x2.95x4.5 M2x10 P3x4x9.5 B4x7x2.5 M3x14 14

17 Assembly of Tail Blades 尾旋翼片組裝 N3x5.5L M3x14 Assembly of Tail Boom Set 尾管總成組立 1.Insert the tail boom, make sure the gear mesh is approximately 0.1mm. 2. Fix M3x18 screws in P 將傳動尾管置入機身並確認齒隙約 0.1mm 2. 鎖緊 P.7 頁的 M3x18 螺絲 0.1mm M3x18 15

18 Tail Boom Brace Assembly 支撐桿組裝 1. Assemble the tail boom brace. 1. 將支撐桿鎖上機身 P3x6x4 M3x14 Ø3x8 M3x6 Main Rotor Linkage Rod Assembly 主旋翼拉桿組裝 1.Assemble the linkage rod (A) x 3 2.Assemble the linkage rod (B) x 2 A 41.6mm 23.5mm B 49.5mm 31mm 1. 製作拉桿組 A 3 支 2. 製作拉桿組 B 2 支 M3x22 B N3x5.5L A M3x6 2pcs 16

19 Throttle Curve and Pitch Curve 螺距 & 油門曲線設定 Normal Flight 一般飛行模式 Freestyle/Aggresive 特技 1 模式 100% 95% 92.5% 91% 90% 91% 92.5% 100% Throttle Curve 油門曲線 64% 70% 74% 80% 40% 0% Point-L Point-1 Point-2 Point-3 Point-4 Point-5 Point-H Point-L Point-1 Point-2 Point-3 Point-4 Point-5 Point-H Normal Flight 一般飛行模式 100% Freestyle/Aggressive 特技 1 模式 100% 82% 83% Pitch Curve 螺距曲線 40% 44% 48.5% 55% 66.5% 50% 66.5% 33% 16.5% Point-L Point-1 Point-2 Point-3 Point-4 Point-5 Point-H 0% Point-L Point-1 Point-2 Point-3 Point-4 Point-5 Point-H Setting Pitch 主旋翼螺距設定 1.Make sure all parts are level 2.Moving throttle stick to lowest Setting pitch to -2~-3 degree 3.Suggested maximum pitch is +-13 degree, cyclic pitch is 10 degree. 1. 確認各部位水平 ( 調整主旋翼拉桿長度至主槳 0 度 ) 2. 油門搖桿至最低點時, 主旋翼螺距約 -2~-3 度 3. 原廠建議最大 Pitch 為 ±13 度, 循環螺距為 10 度 - 2 o level 水平 + 13 o level 水平 Linkage rod 主旋翼拉桿 level 水平 - 13 o level 水平

20 Parts 零件表 X4 Tail Rotor Blade Set(70mm) X4 尾旋翼 (70mm) X4 CNC Tail Support Clamp(Silver anodized) X4 CNC 水平翼固定座 ( 電鍍亮銀 ) X4 FES CNC Main Rotor Yoke Set (Black anodized) X4 FES CNC 主旋翼頭 ( 電鍍黑 ) Ball with Stand(4.8mm) 4.8 球頭 Mast Collar Set 主軸輪擋 X4 CNC Main Grip Set (Black anodized) X4 CNC 主旋翼夾頭 ( 電鍍黑 ) X4 FES Washout Arm Assembly (Black anodized) X4 FES 剪型臂組 ( 電鍍黑 ) X4 FES CNC Main Grip Levers (Black anodized) X4 FES 主旋翼舵柄組 ( 電鍍黑 ) X4 Spindle Shafts X4 橫軸 X4 FES Main Masts (8mm) X4 FES 主軸組 (8mm) X4 FES 2 Blade Rotor Head Ass'y(for 8mm Mast) X4 FES 兩槳旋翼頭總成 (8mm 主軸用 ) X4 Washer Pack X4 墊片包 Damper rubber (Hardness 95) 橫軸橡皮墊 ( 硬度 95) Main Blade Linkage Rod (2x31mm)x2 不鏽鋼連桿組 (2x31mm)x2(2x23.5mm)x (2x23.5mm)x X4 CNC Stop Plate (Black anodized) X4 CNC 煞車盤 ( 電鍍黑 ) X4 Canopy Posts(Silver anodized) X4 艙罩支柱 X4 CNC Swashplate (Black anodized) X4 CNC 十字盤 ( 電鍍黑 ) X4 FRP Painted Canopy X4 玻纖噴漆座艙組 X4 Right CF Frame with Metal parts X4 右碳纖側板含附件 X4 Left CF Frame with Metal parts X4 左碳纖側板含附件 X4 Stiffening Plates and Mounts for electronics(cf) X4 碳纖陀螺儀座及電池座及強化板組 X4 Servo Mounts and Mast Mount X4 上主軸版伺服機座組 mm Steel One Way Gear Ass'y(19T) 8mm 單向齒輪 (19T) Pulley Shaft with Steel Gear(14T) 皮帶齒軸附鋼齒 (14T) mm New One Way Gear Shaft Set(L43) 8mm 新單向軸 (L43) Rear Main Gear(61T) 61T 齒輪 X4 Bearing Mount for CF Frames X4 碳纖側板專用軸承座 X4 CNC Boom Clamps (Silver anodized) X4 CNC 尾管固定座 ( 亮銀 ) Front Gear Hub Set 前齒輪轂 Rear Gear Hub Set 主齒輪轂 Skid Set X4 滑橇組 ( 亮銀 ) Alu Square Post with 3mm thread hole (5x5x23.5mm) and Round Post (3x4.8x23.5mm) 方鋁柱附 3mm 牙孔 (5x5x23.5mm) 及圓鋁柱 (3x4.8x23.5mm) CF main blades (425L-CFA) 碳纖槳 425L(CFA) X4 Fin and Tail(CF) X4 碳纖尾翼組 X4 CF Tail Rotor Blade Set(77mm) X4 碳纖尾旋翼 (77mm) X4 CNC Integrated Tail Gear Case(Black anodized X4 一體成型尾殼座組 ( 電鍍黑適用軸傳版 ) & Shaft version) X4 CNC Tail Rotor Grips with Thrust Bearings X4 CNC 尾旋翼夾頭附止推軸承 (5mm 尾軸用 ) (for 5mm tail output shaft) CNC Tail Pitch Slider Set(for 5mm tail output shaft) CNC 螃蟹夾組 (5mm 尾軸用 ) X4 Tail Boom (Black anodized) X4 尾管 ( 電鍍黑 ) X4 Torque Tube Tail Boom Assembly X4 CNC 軸傳動尾管總成 ( 電鍍黑 ) (Black anodized)

21 Parts 零件表 X4 Tail Boom Support (Silver anodized) X4 支撐桿 ( 亮銀 ) mm Straight Tail Pushrod 500mm 直尾拉桿 ( 適用 X4 系列 ) X4 Tail Output Shaft X4 尾軸 X4 Torque Tube Drive Gear Set X4 尾軸傳動齒輪包 X4 Tail Hub Set (for #213652) X4 尾旋翼頭 ( 適用 #213652) Tail Pitch Control Lever Set 尾舵角片 Tail Support Clamp 尾管夾 Rudder Control Guide 拉桿座 X4 CNC Torque Tube with bearing (for 425L blades) X4 CNC 尾傳動軸桿組 ( 適用 425mm 槳 ) B. Pack(3x8x3)x4 軸承 (3x8x3)x B. Pack(4x9x4)x2 軸承 (4x9x4)x B. Pack(3x6x2.5)x4 軸承 (3x6x2.5)x B. Pack(5x11x4)x4 軸承 (5x11x4)x B. Pack(8x16x5)x2 軸承 (8x16x5)x B. with washer (8x12x3.5)x2 軸承 (8x12x3.5)x2( 附墊片 ) B. Pack (6x13x3.5)x4 軸承 (6x13x3.5)x B. Pack (6x13x5)x4 軸承 (6x13x5)x Thrust B. (T6x12x4.5)x2 止推軸承包 (T6x12x4.5)x Ball Links Pack(4.8mm) 拉桿頭 (4.8mm) X4 Screws Combo Pack(M3) X4 螺絲組合包 (M3) Machine Screws-Silver-Semi-(2x8)x12pcs 十字機械牙螺絲包 - 銀色 - 半牙 (2x8)x12 個 Socket Head Cap Screw - Black (M4x10)x10pcs 內六角螺絲包 - 黑色 (M4x10)x10 個 Washer Pack(W3.1x4.6x0.6) 墊片包 (W3.1x4.6x0.6) Nut (N2x4)x10pcs 螺帽 (N2x4)x10 個 Nut Combo Pack(N3x5.5) 螺帽組合包 (N3x5.5) B. (5x10x4) 軸承 (5x10x4) Socket Set Screw(M3x3mmx10pcs) 內六角止付螺絲 (M3x3mmx10 個 )

22 FAX: MADE IN TAIWAN

Preface / Liability Disclaimer 前言 / 免責聲明 Motor assembly 馬達組裝 P.7 Academy of Model Aeronautics (AMA) Tail case assembly 尾殼組裝 P.8 Main shaft mounts asse

Preface / Liability Disclaimer 前言 / 免責聲明 Motor assembly 馬達組裝 P.7 Academy of Model Aeronautics (AMA) Tail case assembly 尾殼組裝 P.8 Main shaft mounts asse INSTRUCTION MANUAL V.0. Specifications Overall Length (with Canopy): 690 mm Main Rotation Diameter: 78 ~ 808 mm Main blade length: 5 ~ 60 mm Overall Height: 0 mm Overall Width: 90 mm Tail Blade Length: