Machine Model: PT-9800PCN/PT-9700PC IMPORTANT - PLEASE READ CAREFULLY This documentation ( Documentation ) gives you information that will assist you

Size: px

Start display at page:

Download "Machine Model: PT-9800PCN/PT-9700PC IMPORTANT - PLEASE READ CAREFULLY This documentation ( Documentation ) gives you information that will assist you"

暑温
5 years ago
Views:

2 Machine Model: PT-9800PCN/PT-9700PC IMPORTANT - PLEASE READ CAREFULLY This documentation ( Documentation ) gives you information that will assist you in controlling your Machine Model. You may use the Documentation only if you first agree to the following conditions. If you do not agree to the following conditions, you may not use the Documentation. Condition of Use You may use and reproduce the Documentation to the extent necessary for your own use of your Machine Model ( Purpose ). Unless expressly permitted in the Documentation, you may not; (i) copy or reproduce the Documentation for any purpose other than the Purpose, (ii) modify, translate or adapt the Documentation, and/or redistribution to any third party, (iii) rent or lease the Documentation to any third party, or, (iv) remove or alter any copyright notices or proprietary rights legends included within the Documentation. No Warranty a. Any updates, upgrades or alteration of the Documentation or Machine Model will be performed at the sole discretion of rother. rother may not respond to any request or inquiry about the Documentation. b. THIS DOCUMENTATION IS PROVIDED TO YOU "AS IS" WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS OR IMPLIED, INCLUDING, UT NOT LIMITED TO, THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. ROTHER DOES NOT REPRESENT OR WARRANT THAT THIS DOCUMENTATION IS FREE FROM ERRORS OR DEFECTS. c. IN NO EVENT SHALL ROTHER E LIALE FOR ANY DIRECT, INDIRECT, PUNITIVE, INCIDENTAL, SPECIAL, CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER, ARISING OUT OF THE USE, INAILITY TO USE, OR THE RESULTS OF USE OF THE DOCUMENTATION OR ANY SOFTWARE PROGRAM OR APPLICATION YOU DEVELOPED IN ACCORDANCE WITH THE DOCUMENTATION. 2

3 [Contents] Control code list...6 Print area...9 Characters...10 Print position Line feed amount...12 Document creation flow...13 Control command details...15 Character/style selection commands...15 ESC R Select international character set...15 ESC k Select font (Over sea model only)...17 ESC t Select character code table...17 Text printing commands...18 ESC 4 Apply italic style...18 ESC 5 Cancel italic style...18 ESC E Apply bold style...18 ESC F Cancel bold style...19 ESC G Apply double-strike printing...19 ESC H Cancel double-strike printing...19 ESC W Specify double-width characters...20 SI Specify compressed characters...20 ESC SI Specify compressed characters...20 DC2 Cancel compressed characters...21 ESC - Apply/cancel underlining...21 ESC! Global formatting...22 ESC X Specify character size...23 ESC i f Apply/cancel a frame (global)...23 CAN Clear text...24 DEL Delete one character...25 ESC CR Not available...25 Line feed commands...26 ESC 0 Specify line feed of 1/8 inch...26 ESC 2 Specify line feed of 1/6 inch...26 ESC 3 Specify line feed of n/180 inch...26 ESC A Specify line feed of n/60 inch...27 Horizontal movement commands

4 CR Carriage return...28 ESC $ Specify absolute horizontal position...28 ESC \ Specify relative horizontal position...29 ESC a Specify alignment...29 Vertical movement commands...30 LF Line feed...30 FF Page feed...30 ESC J Forward paper feed...30 Paper formatting...31 ESC i l Specify label length...31 ESC i m Specify margin width...31 Printer control commands...32 Initialize...32 Graphics commands...33 ESC * Select bit image...33 ESC K 8-dot single-density bit image...38 ESC L 8-dot double-density bit image...39 ESC Y 8-dot double-speed double-density bit image...40 ESC Z 8-dot quadruple-density bit image...40 Kanji commands...41 FS & Specify kanji mode (Chinese model only)...41 FS. Cancel kanji mode (Chinese model only)...41 FS Y Specify kanji size...41 FS - Apply kanji underlining...42 FS SI Specify half-width characters...43 FS DC2 Cancel half-width characters...43 FS k Select font (Over sea model only)...43 Advanced commands...44 ESC i ar code...44 ESC i Q 2D bar code (QR Code)...48 ESC i P Specify QR Code version...52 ESC i V 2D bar code (PDF417)...53 ESC i D 2D bar code (DataMatrix)...57 ESC i M 2D bar code (MaxiCode)...60 ESC i F Print transferred data...62 ESC i a Switch command mode...66 ESC i S Request printer status

5 ESC i L Apply/cancel rotated printing...70 ESC i C Specify cut setting...70 ESC i U Specify baud rate...71 ESC i U b Specify bit length...71 ESC i U P Specify parity setting...72 ESC i U C Specify busy control...72 Character code...73 Standard character code table for ESC/P codes (Over sea modl only)...73 Eastern European character code table (Windows 1250) (Over sea modl only) Western European character code table (Windows 1252) (Over sea modl only) Appendix CG list (Chinese modl only)...76 Chinese character catalog (based on G2312)...78 ROTHER PT-9800PCN/9700PC ESC/P specifications

6 Control code list Character/style selection ESC R 1 52 Select international character set ESC k 1 6 Select font ESC t 1 74 Select character code table Text printing ESC Apply italic style ESC Cancel italic style ESC E 1 45 Apply bold style ESC F 1 46 Cancel bold style ESC G 1 47 Apply double-strike printing ESC H 1 48 Cancel double-strike printing ESC W 1 57 Specify double-width characters SI 0F Specify compressed characters ESC SI 1 0F Specify compressed characters DC2 12 Cancel compressed characters ESC - 1 2D Apply/cancel underlining ESC! 1 21 Global formatting ESC X 1 58 Specify character size ESC i f Apply/cancel a frame (global) CAN 18 Clear text DEL 7F Delete one character ESC CR 1 0D Not available Line feeds ESC Specify line feed of 1/8 inch ESC Specify line feed of 1/6 inch ESC Specify minimum line feed ESC A 1 41 Specify line feed of n/60 inch Horizontal movement CR 0D Carriage return ESC $ 1 24 Specify absolute horizontal position ESC \ 1 5C Specify relative horizontal position ESC a 1 61 Specify alignment 6

7 Vertical movement LF 0A Line feed FF 0C Page feed ESC J 1 4A Forward paper feed Paper formatting ESC i l C Specify label length ESC i m D Specify margin width Printer control 1 40 Initialize Graphics commands ESC * 1 2A Select bit image ESC K dot single-density bit image ESC L 1 4C 8-dot double-density bit image ESC Y dot double-speed double-density bit image ESC Z 1 5A 8-dot quadruple-density bit image Kanji commands FS & 1C 26 Specify kanji mode FS. 1C 2E Cancel kanji size FS Y 1C 59 Specify kanji size FS - 1C 2D Apply kanji underlining FS S 1C 0F Specify half-width characters FS DC2 1C 12 Cancel half-width characters FS k 1C 6 Select font 7

8 Advanced commands ESC i ar code ESC i Q D bar code (QR Code) ESC i P Specify QR Code version ESC i V D bar code (PDF417) ESC i D D bar code (DataMatrix) ESC i M D 2D bar code (MaxiCode) ESC i F Print transferred data ESC i a Switch command mode ESC i S Request printer status ESC i L C Apply/cancel rotated printing ESC i C Specify cut setting ESC i U Specify baud rate ESC i U b Specify bit length ESC i U P Specify parity setting ESC i U C Specify busy control 8

9 Print area The print area for each tape width is listed below. Length (4) (label length) Width (1) (tape width) 2 Printable area 5 Top margin (3) ottom margin (3) Left margin (6) Right margin (6) Type Width (mm) Printable area (vertical) (mm/dots) Top/bottom margins (mm) Length (mm) Printable area (horizontal) mm/dots Left/right margins (mm) Dot position *1 Max. no. of printed lines / ~ / ~ / ~ / ~ / ~ / ~ / ~ *1 The dot position for the lowest dot is specified as 1. (1 through 384) The maximum length (4) is 1 m, and the minimum left and right margins (6) are 1 mm. 9

10 Characters <Overseas> This system uses single-byte character codes and is installed with two bitmap fonts (Letter Gothic and Helsinki). Each font has six sizes: 21 dots, 28 dots, 44 dots, 56 dots, 88 dots and 120 dots. <Chinese> The single-byte character codes are installed with one bitmap fonts (Helsinki). Each font has six sizes: 24 dots, 32 dots, 48 dots, 64 dots. The double-byte character codes are available G 2312, one bitmap fonts (boldface). Each font has six sizes: 24 by 24 dots, 32 by 32 dots, 48 by 48 dots, 64 by 64 dots. Character size <Overseas> Each font is available in full size, compressed (half width) and double width. Full size Half width Double width Line-drawing characters ( ) and shaded characters appear with the width of the Letter Gothic font, regardless of the specified font setting. 10

11 Print position The print position is the standard position for printing characters, bitmaps and bar codes. With the print position, there is a horizontal print position, which is the reference point for vertical position movement. Each character is arranged so that their top edge aligns with the print position. The baseline of each character is the bottom edge of the character, regardless of size, font, etc. Print position A aseline position All characters on the same line are printed so that the baseline position is the same for each character. If the text consists of characters with different heights, the characters are aligned on the baseline of the tallest character in the line of text. Print position A A A aseline position In addition, underlines are printed 4 dots below the baseline position. itmaps, bar codes and transferred images These types of image data are treated in the same way as characters and are printed so that the bottom edge of the image aligns with the baseline. Same line Horizontal movement to the right between characters or images is regarded as being on the same line; however, movement to the left is regarded as being on different lines if text wrapping occurs. 11

12 Line feed amount The line feed amount is the amount of vertical movement from the print position of one line to the print of the next line. HHHHHHHHHHHHH HHHHHHHHHHHHH HHHHHHHHHHHHH Line feed amount The line feed amount is specified using ESC 0, ESC 2, ESC A and ESC 3. 12

13 Document creation flow The flow for creating documents is shown below. A Switch command mode (ESC i a) and Initialize Format settings 1. Apply/cancel rotated printing (ESC i L) 2. Specify line feed amount (ESC 0, ESC 2, ESC 3 and ESC A) C Print operations 1. Specify print position Specify vertical position (ESC J) Specify horizontal position (ESC $, ESC \ and ESC a) 2. Transfer print data (one line) If necessary, transfer text processing codes (see D), bit images, bar codes and downloaded data (see E). 3. End of line and feed paper (CR and LF) 4. Repeat 1 through 3 described above. 5. End of page, Specify cut setting (ESC i C) and Page feed (FF) 6. Repeat 1 through 6 described above. 7. End of document 13

14 D Text operations 1. Select character set Select font (ESC k) Select character code (ESC t) Select international character set (ESC R) Specify character size (ESC X) 2. Character style (ESC 4, ESC 5, ESC E, ESC F, ESC G, ESC H, ESC W, SI, ESC SI, DC2, ESC and ESC!) 3. Character code 4. ANK mode/kanji mode select.(fs & FS.) 5. Specify Character code for Kanji code Character size (FS Y) 6. Decorating for Kanji. (FS -, FS!, FS SI, FS DC2.) 7. Kanji Code *Repeat steps 1 through 7, as necessary. The steps 4 through 7 are Chinese model only. E it image (ESC *, ESC K, ESC L, ESC Y and ESC Z) ar code (ESC i ) 2D bar code (ESC i Q, ESC i V and ESC i D) Downloaded data (ESC i F) With transferred data, the image data must first be transferred and saved on the main unit. 14

15 Control command details Character/style selection commands ESC R Select international character set [ASCII] ESC R n [Decimal] n [Hexadecimal] 1 52 n [Parameters] 0 n 13, 64 Selects the character set for the country, and switches some character codes in the code table according to the value of n. n=0: USA n=1: France n=2: Germany n=3: UK n=4: Denmark n=5: Sweden n=6: Italy n=7: Spain n=8: Japan n=9: Norway n=10: Denmark II n=11: Spain II n=12: Latin America n=13: South Korea n=64: Legal The following 12 codes are changed. 23h, 24h, 40h, 5h, 5Ch, 5Dh, 5Eh, 60h, 7h, 7Ch, 7Dh, 7Eh The default setting is n=0 When using the standard character code table, printing is performed according to the specified international character set. 15

16 [Example] Code 5Ch ESC R 08h 5Ch FF Print result \ 16

17 ESC k Select font (Over sea model only) [ASCII] ESC k n [Decimal] n [Hexadecimal] 1 6 n [Parameters] 0 n 1 Selects the font. itmap fonts n=0 Helsinki n=1 Letter Gothic The default value is n=0 (Helsinki). ESC t Select character code table [ASCII] ESC t n [Decimal] n [Hexadecimal] 1 74 n [Parameters] n=0, 1, 2 From the three built-in character code tables, select the character code table to be used. n=0: Standard character code table n=1: Eastern European character code table n=2: Western European character code table n=3: (Spare) The default setting is n=0. 17

18 Text printing commands ESC 4 Apply italic style [ASCII] ESC 4 [Decimal] [Hexadecimal] 1 34 [Parameters] None Applies the italic style to the following text. ESC 5 Cancel italic style [ASCII] ESC 5 [Decimal] [Hexadecimal] 1 35 [Parameters] None Cancels the italic style. [Example] Code AC ESC 4 DEF ESC 5 GHI FF Print result ACDEFGHI ESC E Apply bold style [ASCII] ESC E [Decimal] [Hexadecimal] 1 45 [Parameters] None Prints the following text in bold. 18

19 ESC F Cancel bold style [ASCII] ESC F [Decimal] [Hexadecimal] 1 46 [Parameters] None Cancels the bold style. [Example] Code AC ESC E DEF ESC F GHI FF Print result ACDEFGHI ESC G Apply double-strike printing [ASCII] ESC G [Decimal] [Hexadecimal] 1 47 [Parameters] None Prints the following text in bold. ESC H Cancel double-strike printing [ASCII] ESC H [Decimal] [Hexadecimal] 1 48 [Parameters] None Cancels the bold style. [Example] Code AC ESC E DEF ESC F GHI FF Print result ACDEFGHI 19

20 ESC W Specify double-width characters [ASCII] ESC W n [Decimal] n [Hexadecimal] 1 57 n [Parameters] n=0 and 1 or 48 and 49 Specifies double-width characters. If n=1 or 49 ( 1 ), double-width characters are specified. If n=0 or 48 ( 0 ), double-width characters are cancelled. [Example] Code AC ESC W 1 AC ESC W 0 AC FF Print result ACACAC SI Specify compressed characters [ASCII] SI [Decimal] 15 [Hexadecimal] 0F [Parameters] None Prints the following text in half-width characters. ESC SI Specify compressed characters [ASCII] ESC SI [Decimal] [Hexadecimal] 1 0F [Parameters] None Same as SI 20

21 DC2 Cancel compressed characters [ASCII] DC2 [Decimal] 18 [Hexadecimal] 12 [Parameters] None Cancels compressed characters specified with SI. ESC - Apply/cancel underlining [ASCII] ESC - n [Decimal] n [Hexadecimal] 1 2D n [Parameters] n=0 and 1 or 48 and 49 Applies or cancels underlining. If n=1, underlining is applied. If n=0, underlining is cancelled. The underlining specified by this code is a continuous line. Spaces between characters and words are also underlined. [Example] Code AC ESC - 1 AC ESC - 0 AC FF Print result ACACAC 21

22 ESC! Global formatting [ASCII] ESC! n [Decimal] n [Hexadecimal] 1 21 n [Parameters] 0 n 255 Specifies a combination of the various print modes. Specifies modes according to the bit value of n. A combination of multiple print modes can be specified at one time. it Underline Italics Not used old old Not used Not used Not used 0 Cancel Cancel Not used Cancel Cancel Not used Not used Not used [Example] To apply underlining and the italic style at one time Code AC ESC! C0h AC ESC! 00h AC FF Print result ACACAC 22

23 ESC X Specify character size [ASCII] ESC X n [Decimal] n [Hexadecimal] 1 58 n [Parameters] 0 n 6 or 30h n 36h Specifies the character size. <Over Sea> The character size can be set to AUTO or a fixed size (six sizes). If n=0 (or 30h), the AUTO size is applied. If n=1 (or 31h), the 4-point size is applied. (21 dots) If n=2 (or 32h), the 6-point size is applied. (28 dots) If n=3 (or 33h), the 9-point size is applied. (44 dots) If n=4 (or 34h), the 12-point size is applied. (56 dots) If n=5 (or 35h), the 18-point size is applied. (88 dots) If n=6 (or 36h), the 24-point size is applied. (120 dots) Same as FS Y <China> If n=0 (or 30h), the AUTO size is applied. If n=1 (or 31h), the 5-point size is applied. (24 dots) If n=2 (or 32h), the 6-point size is applied. (32 dots) If n=3 (or 33h), the 10-point size is applied. (48 dots) If n=4 (or 34h), the 13-point size is applied. (64 dots) If n=5 (or 35h), the 19-point size is applied. (48 dots 2) If n=6 (or 36h), the 26-point size is applied. (64 dots 2) Same as FS Y ESC i f Apply/cancel a frame (global) [ASCII] ESC i f [Decimal] [Hexadecimal] [Parameters] 0 n 1 or 30h n 31h 23

24 Applies a frame around the entire text. If n=0 (or 30h), the frame is cancelled. If n=1 (or 31h), a frame is applied. CAN Clear text [ASCII] CAN [Decimal] 24 [Hexadecimal] 18 [Parameters] None Clears all text, image data and bar codes that were received. 24

25 DEL Delete one character [ASCII] DEL [Decimal] 127 [Hexadecimal] 7F [Parameters] None The immediately preceding character within the same line is deleted. If the immediately preceding data is a bar code, the bar code is deleted. Image data is not deleted. ESC CR Not available [ASCII] ESC CR n [Decimal] n [Hexadecimal] 1 0D n [Parameters] 0 n 255 Does nothing. 25

26 Line feed commands ESC 0 Specify line feed of 1/8 inch [ASCII] ESC 0 [Decimal] [Hexadecimal] 1 30 [Parameters] None Specifies a line feed of 1/8 inch (approximately 0.32 cm). ESC 2 Specify line feed of 1/6 inch [ASCII] ESC 2 [Decimal] [Hexadecimal] 1 32 [Parameters] None Specifies a line feed of 1/6 inch (approximately 0.42 cm). ESC 3 Specify line feed of n/180 inch [ASCII] ESC 3 n [Decimal] n [Hexadecimal] 1 33 n [Parameters] 0 n 255 Specifies a line feed of n/180 inch per text line. If n is less than 24, the line feed amount is set to 24/180 inch (approximately 0.34 cm). 26

27 ESC A Specify line feed of n/60 inch [ASCII] ESC A n [Decimal] n [Hexadecimal] 1 41 n [Parameters] 0 n 255 Specifies a line feed of n/60 inch per text line. If n is less than 8, the line feed amount is set to 8/60 inch (approximately 0.34 cm). 27

28 Horizontal movement commands CR Carriage return [ASCII] CR [Decimal] 13 [Hexadecimal] 0D [Parameters] None Performs a line feed of the amount specified by a line feed command (ESC 0, ESC 2, ESC 3 and ESC A). If no line feed amount has been specified, it is automatically specified depending on the width of the tape. The next print position is the beginning of the next line. A line feed command immediately after a carriage return is ignored. ESC $ Specify absolute horizontal position [ASCII] ESC $ n1 n2 [Decimal] n1 n2 [Hexadecimal] 1 24 n1 n2 [Parameters] 0 n1 255, 0 n2 255 Specifies an absolute print position (in units of 1/60 inch) for the next data. An absolute print position specifies the horizontal print position from the left margin. The next character is printed at a position (n * n2) / 60 inch from the left margin. * However, since the printable length is 1 meter, an actual value greater than 2362/60 inches will result in an error during printing 28

29 ESC \ Specify relative horizontal position [ASCII] ESC \ n1 n2 [Decimal] n1 n2 [Hexadecimal] 1 5C n1 n2 [Parameters] 0 n1 255, 0 n2 255 Specifies a relative print position (in units of 1/180 inch) for the next data. A relative print position specifies the horizontal print position based on the current position. The next character is printed at a position (n * n2) / 180 inch from the current position. A relative position cannot be specified to the left (in the negative direction). However, since the printable length is 1 meter, an actual value greater than 7086/180 inches will result in an error during printing This command is available only with left alignment. ESC a Specify alignment [ASCII] ESC a n [Decimal] n [Hexadecimal] 1 61 n [Parameters] 0 n 3 or 0 n 3 The following data is printed with the alignment described below, depending on the value of n. n=0 specifies left alignment. n=1 specifies center alignment. n=2 specifies right alignment. n=3 specifies justified alignment. The default setting is n=0. The last alignment setting received is applied to all of the print data. If an absolute horizontal position or a relative horizontal position is specified, the text must be aligned on the left when it is printed. 29

30 Vertical movement commands LF Line feed [ASCII] LF [Decimal] 10 [Hexadecimal] 0A [Parameters] None Performs the same line feed operation as CR. A carriage return command immediately after a line feed is ignored. FF Page feed [ASCII] FF [Decimal] 12 [Hexadecimal] 0C [Parameters] None Starts printing. Clears the text, image data and bar codes after printing. If the data does not fit within the printable height of the tape, the data is divided and printed onto multiple pages. If the length of the print data exceeds 1 meter, the LED lights up to indicate that an error has occurred. ESC J Forward paper feed [ASCII] ESC J n [Decimal] n [Hexadecimal] 1 4A n [Parameters] 0 n 255 Finishes input of the current line, then moves the vertical print position forward by n/180 inch. If n is less than 24, the feed amount is 24/180 inch (approximately 0.34 cm). 30

31 Paper formatting ESC i l Specify label length [ASCII] ESC i l n1 n2 [Decimal] n1 n2 [Hexadecimal] C n1 n2 [Parameters] len=n1+n2 256 (len=0 or 36 len 7200) Specifies the label length (len) in units of 1/180 inch. The range in which the label length can be set is 0.2 to 40 inches. len=0 specifies the AUTO setting. ESC i m Specify margin width [ASCII] ESC i m n1 n2 [Decimal] n1 n2 [Hexadecimal] D n1 n2 [Parameters] mgn=n1+n2 256 (7 mgn 720) Specifies the margin width (mgn) in units of 1/180 inch. The range in which the margin width can be set is 0.04 to 4 inches. 31

32 Printer control commands Initialize [ASCII] [Decimal] [Hexadecimal] 1 40 [Parameters] None Resets all parameters to their default settings. (See below.) Item Command mode (ESC/P, Raster or P-touch Template) Communication settings (aud rate, Parity, it length and usy control) Received text and bar codes Received image data Line feed amount Relative position setting Absolute position setting Font Character size Italics old/double-strike printing After Initialization No change No change Cleared Cleared AUTO Cleared Cleared Helsinki (Over sea model only) AUTO OFF OFF Underline OFF Character width Normal (Half-width and double-width characters are cancelled.) Character code table Standard character code table International character set USA kanji mode ON (Chinese model only) Frame None Rotate OFF Text alignment Left Margins 2 mm Label length setting AUTO ar code protocol CODE39 ar code width Small ar code ratio 3:1 ar code check digit OFF Characters below bar codes ON Full cut ON Half cut ON Chain printing OFF 32

33 Graphics commands ESC * Select bit image [ASCII] ESC * m n1 n2 data [Decimal] m n1 n2 data [Hexadecimal] 1 2A m n1 n2 data [Parameters] m=0, 1, 2, 3, 4, 6, 32, 33, 38, 39, 40, 71, 72 or 73 0 n1 255, 0 n2 255 The data contains image data that is n1 + n2 * 256 bytes when m=0, 1, 2, 3, 4 or 6, (n1 + n2 * 256) * 3 bytes when m=32, 33, 38, 39 or 40, or (n1 + n2 * 256) * 6 bytes when m=71, 72 or 73. Selects and outputs a bit image according to the value of m. n1 and n2 indicate the number of dot positions. n1: The remainder from dividing the number of dot positions by 256 n2: The quotient from dividing the number of dot positions by 256 m Horizontal dot Vertical dot Horizontal dot Vertical dot density density resolution resolution 0 60 DPI 60 DPI 6/360 inch 6/360 inch DPI 60 DPI 3/360 inch 6/360 inch DPI 60 DPI 3/360 inch 6/360 inch DPI 60 DPI 2/360 inch 6/360 inch 4 80 DPI 60 DPI 4/360 inch 6/360 inch 6 90 DPI 60 DPI 4/360 inch 6/360 inch DPI 180 DPI 6/360 inch 2/360 inch DPI 180 DPI 3/360 inch 2/360 inch DPI 180 DPI 4/360 inch 2/360 inch DPI 180 DPI 2/360 inch 2/360 inch DPI 180 DPI 1/360 inch 2/360 inch DPI 360 DPI 2/360 inch 1/360 inch DPI 360 DPI 1/360 inch 1/360 inch DPI 360 DPI 1/360 inch 1/360 inch 33

34 When m=0, 1, 2, 3, 4 or 6 n1 and n2 indicate the number of dot positions. n1: The remainder from dividing the number of dot positions by 256 n2: The quotient from dividing the number of dot positions by Relationship between the image data and the dots First, the data is lined up in one row as shown below. MS LSM n1+n2*256 byte One dot of the image data is enlarged according to the value of m, as shown below. m=0 m=1 m=2 m=3 m=4 m=6 As a result, the image is sized depending on the value of m, as shown below. m=0 48 dots vertically (n1 + n2 * 256) * 6 dots horizontally m=1 48 dots vertically (n1 + n2 * 256) * 3 dots horizontally m=2 48 dots vertically (n1 + n2 * 256) * 3 dots horizontally m=3 48 dots vertically (n1 + n2 * 256) * 2 dots horizontally m=4 48 dots vertically (n1 + n2 * 256) * 4 dots horizontally m=6 48 dots vertically (n1 + n2 * 256) * 4 dots horizontally 34

35 When m=32, 33, 38, 39 or 40 n1 and n2 indicate the number of dot positions. n1: The remainder from dividing the number of dot positions by 256 n2: The quotient from dividing the number of dot positions by 256 1st byte 2nd byte 3rd byte Relationship between the image data and the dots First, the data is lined up in three rows as shown below. MS LS MS LS MS LS (n1+n2*256)*3 bytes 35

36 One dot of the image data is enlarged according to the value of m, as shown below. m=32 m=33 m=38 m=39 m=40 As a result, the image is sized depending on the value of m, as shown below. m=32 48 dots vertically (n1 + n2 * 256) * 6 dots horizontally m=33 48 dots vertically (n1 + n2 * 256) * 3 dots horizontally m=38 48 dots vertically (n1 + n2 * 256) * 4 dots horizontally m=39 48 dots vertically (n1 + n2 * 256) * 2 dots horizontally m=40 48 dots vertically (n1 + n2 * 256) * 4 dots horizontally When m=71, 72 or 73 n1 and n2 indicate the number of dot positions. Specify their values as shown below. n1: The remainder from dividing the number of dot positions by 256 n2: The quotient from dividing the number of dot positions by 256 1st byte 2nd to 5th bytes 6th byte Relationship between the image data and the dots 36

37 First, the data is lined up in six rows as shown below. MS LS MS LS MS LS MS LS MS LS MS LS (n1+n2*256)* 6bytes One dot of the image data is enlarged according to the value of m, as shown below. m=71 m=72 m=73 As a result, the image is sized depending on the value of m, as shown below. m=71 48 dots vertically (n1 + n2 * 256) * 2 dots horizontally m=72 48 dots vertically (n1 + n2 * 256) * 1 dot horizontally m=73 48 dots vertically (n1 + n2 * 256) * 1 dot horizontally 37

38 ESC K 8-dot single-density bit image [ASCII] ESC K n1 n2 data [Decimal] n1 n2 data [Hexadecimal] 1 4 n1 n2 data [Parameters] 0 n1 255, 0 n2 255 The data contains image data that is n1 + n2 * 256 bytes. Specifies that an 8-dot standard-density bit image will be printed with the number of dot positions defined by n1 and n2. n1 and n2 indicate the number of dot positions. n1: The remainder from dividing the number of dot positions by 256 n2: The quotient from dividing the number of dot positions by Relationship between the image data and the dots First, the data is lined up in one row as shown below. MS LS n1+n2*256 byte One dot of the image data is enlarged to 6 dots vertically by 6 dots horizontally. As a result, the image becomes 48 dots vertically (n1 + n2 * 256) * 6 dots horizontally. 38

39 ESC L 8-dot double-density bit image [ASCII] ESC L n1 n2 data [Decimal] n1 n2 data [Hexadecimal] 1 4C n1 n2 data [Parameters] 0 n1 255, 0 n2 255 The data contains image data that is n1 + n2 * 256 bytes. Specifies that an 8-dot double-density bit image will be printed with the number of dot positions defined by n1 and n2. Specify n1 and n2 in the same way as with ESC K. First, the data is lined up in one row as shown below. MS LS n1+n2*256 byte One dot of the image data is enlarged to 6 dots vertically by 3 dots horizontally. As a result, the image becomes 48 dots vertically (n1 + n2 * 256) * 3 dots horizontally. 39

40 ESC Y 8-dot double-speed double-density bit image [ASCII] ESC Y n1 n2 data [Decimal] n1 n2 data [Hexadecimal] 1 59 n1 n2 data [Parameters] 0 n1 255, 0 n2 255 The data contains image data that is n1 + n2 * 256 bytes. Specifies that an 8-dot double-speed double-density bit image will be printed with the number of dot positions defined by n1 and n2. Specify n1 and n2 in the same way as with ESC K. ESC Z 8-dot quadruple-density bit image [ASCII] ESC Z n1 n2 data [Decimal] n1 n2 data [Hexadecimal] 1 5A n1 n2 data [Parameters] 0 n1 255, 0 n2 255 The data contains image data that is n1 + n2 * 256 bytes. Specifies that an 8-dot double-density bit image will be printed with the number of dot positions defined by n1 and n2. Specify n1 and n2 in the same way as with ESC K. First, the data is lined up in one row as shown below. MS LS n1+n2*256 byte One dot of the image data is enlarged to 6 dots vertically by 2 dots horizontally. As a result, the image becomes 48 dots vertically (n1 + n2 * 256) * 2 dots horizontally. 40

41 Kanji commands FS & Specify kanji mode (Chinese model only) [ASCII] FS Y& [Decimal] [Hexadecimal] 1C 26 [Parameters] nothing Specifies the kanji mode. The character is represented by double-byte, and enter the one-byte, double-byte in turn. kanji code is based on G2312. FS. Cancel kanji mode (Chinese model only) [ASCII] FS. [Decimal] [Hexadecimal] 1C 2E [Parameters] nothing Cancel kanji mode. FS Y Specify kanji size [ASCII] FS Y n [Decimal] n [Hexadecimal] 1C 59 n [Parameters] 0 n 6 or 30h n 36h Specifies the character size. The character size can be set to AUTO or a fixed size (six sizes). If n=0 (or 30h), the AUTO size is applied. If n=1 (or 31h), the 4-point size is applied. (21 dots) If n=2 (or 32h), the 6-point size is applied. (28 dots) If n=3 (or 33h), the 9-point size is applied. (44 dots) If n=4 (or 34h), the 12-point size is applied. (56 dots) If n=5 (or 35h), the 18-point size is applied. (88 dots) 41

42 If n=6 (or 36h), the 24-point size is applied. (120 dots) FS - Apply kanji underlining [ASCII] FS - n [Decimal] n [Hexadecimal] 1C 2D n [Parameters] n=0 and 1 or 48 and 49 Applies or cancels underlining. If n=1, underlining is applied. If n=0, underlining is cancelled. The underlining specified by this code is a continuous line. Spaces between characters and words are also underlined. 42

43 FS SI Specify half-width characters [ASCII] FS SI [Decimal] [Hexadecimal] 1C 0F [Parameters] None Same as SI FS DC2 Cancel half-width characters [ASCII] FS DC2 [Decimal] [Hexadecimal] 1C 12 [Parameters] None Same as DC2 FS k Select font (Over sea model only) [ASCII] FS k n [Decimal] n [Hexadecimal] 1C 6 n [Parameters] 0 n 1 or 30h n 31h Selects the font. itmap fonts n=0 (or 30h) Helsinki n=1 (or 31h) Letter Gothic The default value is n=0 (Helsinki). 43

44 Advanced commands ESC i ar code [ASCII] ESC i [parameters] or b [bar code data] backslash [Decimal] [parameters] 66 or 98 [bar code data] 92 [Hexadecimal] 1 69 [parameters] 42 or 62 [bar code data] 5C [Parameters] 1 [Parameters]: ar code parameters T or t (type) t0: CODE39 t1: ITF (I-2/5) t2: EAN-13 t3: EAN-8 t4: UPC-A t5: EAN-8 (when the bar code data contains 7 characters) UPC-A (when the bar code data contains 11 characters) EAN-13 (when the bar code data contains 12 characters) * The check digit mark? is not included in the number of characters. t6: UPC-E t9: CODAAR ta: CODE128 tb: GS1-128 (UCC/EAN-128) tc: RSS symbols s (style) Ignored p (number of passes) Ignored R or r (characters below bar code) r0: OFF r1: ON u (units of measurement) Ignored x (horizontal position) Ignored y (vertical offset) Ignored h (height) h n1 n2 Height = n1 + n2 * 256 (dots) 44

45 48 height 384 If height < 48, height = 48. If height > 384, height = 384. However, with tc, the height is as described below. 141 height 384 (RSS-14 Standard) 81 height 384 (RSS-14 Truncated) 81 height 384 (RSS-14 Stacked) 249 height 384 (RSS-14 Stacked Omni) 72 height 384 (RSS Limited) 144 height 384 (RSS Expanded) If height < min., height = min. If height > max., height = max. (A bar code with a large number of stacked rows may be considered out of specifications and unreadable by the reader.) w (width) w0: small w1: medium w2: large E or e (parentheses removed) e0: ON e1: OFF o (RSS symbols model) o0: RSS-14 Standard o1: RSS-14 Truncated o2: RSS-14 Stacked o3: RSS-14 Stacked Omnidirectional o4: RSS Limited o5: RSS Expanded Standard o6: RSS Expanded Stacked c (number of horizontal characters for RSS Expanded Stacked) c No. of horizontal characters This must be an even value where 2 no. of horizontal characters 20. z (ratio between thick and thin bars) z0: (3:1) z1: (2.5:1) z2: (2:1) 45

46 * Note: oth 00H through 09H and 30H through 39H are recognized as the parameter numbers 0 through 9. Parameter types a and b are recognized, even if they are uppercase letters. The parameter "parentheses removed" is available only when GS1-128 (UCC/EAN-128) is selected. The parameter ratio between thick and thin bars is available only when t0, t1 or t9 is selected. If there is no type command or if an invalid type command has been specified, Code 39 is specified. The number of characters that can be entered for each bar code protocol is listed below. t0: 1 to 50 characters (not including * on both sides) t1: 1 to 64 characters t5: 7 characters (EAN-8), 12 characters (EAN-13), 11 characters (UPC-A) t6: 6 characters t9: 3 to 64 characters (with A,, C or D at the beginning and end) ta: 1 to 64 characters tb: 1 to 64 characters tc: 3 to 15 characters (begins with 01 ) (except with RSS Expanded) 1 to 64 numbers or 1 to 40 letters* (for RSS Expanded) * ISO646 characters can be printed. (numbers, letters, spaces,!,, %, &,, (, ), *, +,,, -,., /, :, ;, <, =, >,? and _) 2 or b: eginning of bar code data 3 [ar code data]: Data for the bar code? (generate check digit) Generates a check digit when? is in the bar code data The position of? is irrelevant as long as it is within the bar code data. With CODE128 and GS1-128 (UCC/EAN-128), no check digit is generated. 46

47 If? is entered, "? is treated as bar code data. 4 ackslash: End of bar code data [With protocols CODE39, ITF (I-2/5), EAN-8, EAN-13, UPC-A, UPC-E, CODAAR and RSS symbols] ESC i [parameters] or b [bar code data] \ [With protocols CODE128 and GS1-128 (UCC/EAN-128)] ESC i [parameters] or b [bar code data] \\\ Specifies a bar code image. Since the check digit is automatically generated from the bar code data, the check digit is not sent as bar code data. Since the length of the bar code data is also checked, the data would not be correctly recognized if check digit data is present. With protocols CODE39, ITF (I-2/5), CODAAR, CODE128, GS1-128 (UCC/EAN-128) or RSS Expanded, the buffer length for the bar code image is about 22 cm. A bar code longer than 22 cm will not be printed. The characters that can be entered with CODE128 and GS1-128 (UCC/EAN-128) are the full 128 ASCII characters and the special codes FNC1, FNC2, FNC3 and FNC4. Codes assigned to the special codes FNC1: 86H FNC2: 81H FNC3: 80H FNC4: 84H The control codes and special codes appear as spaces when characters are printed below CODE128 and GS1-128 (UCC/EAN-128) bar codes. Special code FNC1 can also be printed with RSS Expanded. This special code also appears as a space when characters are printed below the bar code. Code assigned to the special code FNC1: 86H 47

48 ESC i Q 2D bar code (QR Code) [ASCII] ESC i [Decimal] [Hexadecimal] Q data data data Format ESC i Q [parameters] [bar code data] \\\ Parameters Unlike with 1D bar codes, all parameters must be specified in order, starting from the top. If a value other than those listed is entered for a parameter, that parameter is set to its default value. 1. Cell size [1-byte decimal] 4 [1-byte decimal] 6 [1-byte decimal] 8 [1-byte decimal] 10 [1-byte decimal] Symbol type [1-byte decimal] 1 [1-byte decimal] 2 [1-byte decimal] 3 3. Linkage setting [1-byte decimal] 0 [1-byte decimal] 1 4. Code number [1-byte decimal] 1 to Number of partitions [1-byte decimal] 2 to 16 Specifies the dot size per cell side. Prints 4 dots per cell side. (default value) Prints 6 dots per cell side. Prints 8 dots per cell side. Prints 10 dots per cell side. Prints 12 dots per cell side. MODEL1 MODEL2 Micro QR Not linked Linked (*1) (default value) Indicates the number of the QR Code that is linked Indicates the total number of the QR Code that are linked 6. Parity data [1-byte hexadecimal] 00 to FF Value (in bytes) of exclusively OR ing all print data (print data before partition) 7. Error correction level [1-byte decimal] 1 High-density level L 7% [1-byte decimal] 2 Standard level M 15% (default value) [1-byte decimal] 3 High-reliability level Q 25% [1-byte decimal] 4 Ultra-high-reliability level H 30% (*2) 8. Data input method [1-byte decimal] 0 Auto input (default value) [1-byte decimal] 1 Manual input Selects whether numerals, alphanumeric characters, kanji characters or binary characters are entered. (*1) With Micro QR, the linkage setting is invalid, and the default setting is used. 48

49 (*2) With Micro QR, error correction level 4 is invalid, and the default setting is used. Supplement: About QR Code linkage setting QR Codes have a linkage setting. A long character string can be divided into 2 to 16 partitions and printed. With ESC/P commands, it is necessary to enter only the number of partitions. For example, enter the bar code data as shown below when the print data is separated into three partitions. ESC i Q or q [parameters for 1st set] [1st set of bar code data] \\\ ESC i Q or q [parameters for 2nd set] [2nd set of bar code data] \\\ ESC i Q or q [parameters for 3rd set] [3rd set of bar code data] \\\ 3. Linkage setting: This determines whether or not the bar code data is partitioned. If the data is not partitioned, enter 0. If the data is not partitioned, the values for 4. Code number, 5. Number of partitions, and 6. Parity data are ignored, therefore, enter 0 as a dummy for these parameters. 4. Code number: This indicates which number the ESC/P command for that QR Code is for. For example, if it is the second of four partitions, this value is 2. If it is the fourth, this value is Number of partitions: For this, enter the number of partitions. 6. Parity data: This is the value (in bytes) of exclusively OR'ing all print data (print data before partitioning). Entering the same value as for the partitioned QR Code ESC/P command indicates that the codes are linked. About exclusive OR'ing in bytes Data is exclusively OR'ed (XOR ed) in bytes and in order. For example, the hexadecimal values for the character string 1234 are 0x31, 0x32, 0x33, 0x34. XOR ing 0x31 and 0x ^= results in (0x03) XOR ing 0x03 and 0x ^= results in (0x30) XOR ing 0x30 and 0x ^= results in (0x04) Therefore, the parity is 0x04. Note: If this parity data value is incorrect, an incorrect QR Code is generated. Summary Printing the character string with a 4-dot cell size, MODEL2, standard error correction level, and automatic data input 49

50 No linkage ESC i Q 0x04 0x02 0x00 0x00 0x00 0x00 0x02 0x \\\ With linkage (separated into three partitions) (The parity for character string is 0x31.) ESC i Q 0x04 0x02 0x01 0x01 0x03 0x31 0x02 0x \\\ ESC i Q 0x04 0x02 0x01 0x02 0x03 0x31 0x02 0x \\\ ESC i Q 0x04 0x02 0x01 0x03 0x03 0x31 0x02 0x \\\ 2 [ar code data]: Data for the bar code If manual input is selected for parameter 8. Data input method, the following single-byte letter must be entered in front of the bar code data. (When entering kanji characters, the Chinese model is not supported.) When entering numerals: N or n When entering alphanumeric characters: A or a When entering kanji characters: K or k When entering binary characters: or b + 4-digit number string With the four-digit number string, specify the number of binary characters to actually be entered. For example, if 12 binary characters are to be entered, specify 0012 (0x30,0x30,0x31,0x32)". Examples 1. With kanji characters: ESC i Q [other parameters] 1 K <Enter kanji.>\\\ 2. With alphanumeric characters: ESC i Q [other parameters] 1 A abcde\\\ 3. With binary characters: ESC i Q [other parameters] ##### \\\ The number of bar code data characters that can be entered differs depending on the model type and input method. MODEL1: 707 alphanumeric characters, 1167 numerals, 486 bytes of binary characters, 299 kanji characters MODEL2: 4296 alphanumeric characters, 7089 numerals, 2953 bytes of binary characters, 1817 kanji characters 50

51 Micro QR: 21 alphanumeric characters, 35 numerals, 15 bytes of binary data, 9 kanji characters * Note: The number of characters that can be entered (listed above) is for an error correction level at a high-density level of L 7%. If the standard level or higher is set, the number of characters that can be entered may decrease. In addition, even if the characters are entered with a high-density level (L) specified, the number of characters that can be entered may decrease due to compression. 3 \\\: End of bar code There must be three backslashes at the end of 2D bar codes. 51

52 ESC i P Specify QR Code version [ASCII] ESC i P n [Decimal] n [Hexadecimal] n [Parameters] 0 n 40 The barcode size can be fixed. The default value is 0. The available versions differ depending on the symbol type used. If a setting other than those listed is specified, the setting returns to its default. The following settings are available for each symbol type. MODEL1 (0 to 14), MODEL2 (0 to 40), Micro QR (0 to 4) 52

53 ESC i V 2D bar code (PDF417) [ASCII] ESC i V data [Decimal] data [Hexadecimal] data Format ESC i V [parameters] [bar code data] \\\ Parameters Unlike with 1D bar codes, all parameters must be specified in order, starting from the top. If a value other than those listed is entered for a parameter, that parameter is set to its default value. 1. Cell size [1-byte decimal] 4 [1-byte decimal] 6 [1-byte decimal] 8 [1-byte decimal] 10 [1-byte decimal] Symbol type [1-byte decimal] 0 [1-byte decimal] 1 [1-byte decimal] 2 [1-byte decimal] 3 3. Data input method [1-byte decimal] 0 [1-byte decimal] 1 4. Error correction capacity type [1-byte decimal] 0 [1-byte decimal] 1 5. Error correction capacity value When level input is selected: [2-byte decimal] 0 to 8 When percentage input is selected: [2-byte decimal] 0 to Symbol size in X direction [1-byte decimal] 0 [1-byte decimal] 1 to 30 Specifies the dot size per cell side. Prints 4 dots per cell side. (default value) Prints 6 dots per cell side. Prints 8 dots per cell side. Prints 10 dots per cell side. Prints 12 dots per cell side. Standard (default value) Truncated Micro PDF417 standard Micro PDF417 CODE128 emulation Auto input inary input (default value) Level input (default value) Percentage input Level input (default value of 0) Percentage input (default value of 0) Auto setting (default value) Manual setting 53

54 * 0 and 1 to 4 with Micro PDF Symbol size in Y direction [1-byte decimal] 0 Auto setting (default value) [1-byte decimal] 3 to 90 Manual setting * 0 and 4 to 44 with MicroPDF Aspect value [2-byte decimal] 1 to 1000 Enter the aspect value. Actually, this is between 0.01 and However, since a decimal point cannot be entered, a value multiplied by 100 is entered. The default is 50. (The actual value is 0.5.) * Note: The aspect value setting is ignored if the symbol size in the X direction or the symbol size in the Y direction is entered manually. Depending on the conditions, the bar code may not be generated or a bar code that cannot be scanned may be generated if the symbol size in the X direction or the symbol size in the Y direction is entered manually. When a large cell size is specified together with a high error correction capacity, printing may not be possible because the print buffer has become full. [With symbol type Micro PDF417] Since the error correction capacity is automatically determined from the symbol size in the X direction, the settings for Error correction capacity type and Error correction capacity value are ignored. The aspect value setting is ignored. The following table shows the values available for the symbol size in the Y direction according to the symbol size in the X direction. If an invalid setting is specified for the symbol size in the Y direction, the default setting is specified. Symbol size in X Symbol size in Y direction direction AUTO AUTO 1 AUTO AUTO AUTO AUTO ar code data The number of bar code data characters that can be entered is listed below alphanumeric characters, 2710 numerals, 1108 bytes of binary data * Note: The number of characters that can be entered (listed above) is for when the error correction 54

55 capacity is set to the lowest level. The number of characters that can be entered may decrease, depending on the error correction capacity value. In addition, even if the characters are entered with the lowest density level specified, the number of characters that can be entered may decrease due to compression. 55

56 [With symbol type Micro PDF417] Maximum of 250 alphanumeric characters, maximum of 366 numerals, maximum of 150 bytes of binary data However, the following table shows the maximum amount of information allowed according to the symbol size in the X and Y directions. X Y Maximum amount of information allowed Alphanumeric characters Numerals inary \\\: End of bar code There must be three backslashes at the end of 2D bar codes. 56

57 ESC i D 2D bar code (DataMatrix) [ASCII] ESC i D data [Decimal] data [Hexadecimal] data Format ESC i D [parameters] [bar code data] \\\ Parameters Unlike with 1D bar codes, all parameters must be specified in order, starting from the top. If a value other than those listed is entered for a parameter, that parameter is set to its default value. 1. Cell size [1-byte decimal] 4 [1-byte decimal] 6 [1-byte decimal] 8 [1-byte decimal] 10 [1-byte decimal] Symbol type [1-byte decimal] 0 [1-byte decimal] 1 3. Vertical size [1-byte decimal] 0 [1-byte decimal] 10 [1-byte decimal] 12 [1-byte decimal] 14 [1-byte decimal] 16 [1-byte decimal] 18 [1-byte decimal] 20 [1-byte decimal] 22 [1-byte decimal] 24 [1-byte decimal] 26 [1-byte decimal] 32 [1-byte decimal] 36 [1-byte decimal] 40 [1-byte decimal] 44 [1-byte decimal] 48 [1-byte decimal] 52 [1-byte decimal] 64 Specifies the dot size per cell side. Prints 4 dots per cell side. (default value) Prints 6 dots per cell side. Prints 8 dots per cell side. Prints 10 dots per cell side. Prints 12 dots per cell side. ECC200 square ECC200 rectangular ECC200 square Vertical no. of cells: AUTO Vertical no. of cells: 10 cells Vertical no. of cells: 12 cells Vertical no. of cells: 14 cells Vertical no. of cells: 16 cells Vertical no. of cells: 18 cells Vertical no. of cells: 20 cells Vertical no. of cells: 22 cells Vertical no. of cells: 24 cells Vertical no. of cells: 26 cells Vertical no. of cells: 32 cells Vertical no. of cells: 36 cells Vertical no. of cells: 40 cells Vertical no. of cells: 44 cells Vertical no. of cells: 48 cells Vertical no. of cells: 52 cells Vertical no. of cells: 64 cells (default value) (default value) 57

58 [1-byte decimal] 72 [1-byte decimal] 80 [1-byte decimal] 88 [1-byte decimal] 96 [1-byte decimal] 104 [1-byte decimal] 120 [1-byte decimal] 132 [1-byte decimal] 144 [1-byte decimal] 0 [1-byte decimal] 8 [1-byte decimal] 12 [1-byte decimal] Horizontal size [1-byte decimal] x Vertical no. of cells: 72 cells Vertical no. of cells: 80 cells Vertical no. of cells: 88 cells Vertical no. of cells: 96 cells Vertical no. of cells: 104 cells Vertical no. of cells: 120 cells Vertical no. of cells: 132 cells Vertical no. of cells: 144 cells ECC200 rectangular Vertical no. of cells: AUTO Vertical no. of cells: 8 cells Vertical no. of cells: 12 cells Vertical no. of cells: 16 cells (default value) ECC200 square Horizontal no. of cells: Same value as vertical size (x) [1-byte decimal] 0 [1-byte decimal] 18 [1-byte decimal] 32 [1-byte decimal] 26 [1-byte decimal] 36 [1-byte decimal] 36 [1-byte decimal] Spare [1-byte decimal] 5 0 ECC200 rectangular 1 When the vertical size is AUTO Horizontal no. of cells: AUTO 2 When the vertical size is 8 cells Horizontal no. of cells: 18 cells Horizontal no. of cells: 32 cells 3 When the vertical size is 12 cells Horizontal no. of cells: 26 cells Horizontal no. of cells: 36 cells 4 When the vertical size is 16 cells Horizontal no. of cells: 36 cells Horizontal no. of cells: 48 cells 5 bytes of dummy data (0) is sent. (default value) * Note: If the vertical size is set to a value other than those listed for ECC200 square, the AUTO setting is selected. If the horizontal size is set to a value different from the vertical size, the setting is changed to the same value as the horizontal size. If the vertical or horizontal size for ECC200 rectangular is set to a value other than those listed, the AUTO setting is selected. 2 [ar code data]: Data for the bar code The maximum number of bar code data characters that can be entered is listed below alphanumeric characters, 3116 numerals, 1556 bytes of binary data 58

展开

(Guangzhou) AIT Co, Ltd V 110V [ ]! 2

(Guangzhou) AIT Co, Ltd V 110V [ ]! 2 (Guangzhou) AIT Co, Ltd 020-84106666 020-84106688 http://wwwlenxcn Xi III Zebra XI III 1 (Guangzhou) AIT Co, Ltd 020-84106666 020-84106688 http://wwwlenxcn 230V 110V [ ]! 2 (Guangzhou) AIT Co, Ltd 020-84106666