TABLE OF CONTENTS [] SPECIFICATIONS... [] CLASSIFICATION... [] WIRING DIAGRAM -. Unit Mount & Ceiling Mount (AL-90/90) Track Mount Type (AL-90).

Transcription

1 Bel-Halo LED DENTAL LIGHT MODEL AL-90 Unit Mount AL-90 Ceiling Mount AL-90 Track Mount AL-90X Swing Mount INSTALLATION and OPERATION INSTRUCTIONS IMPORTANT After installation is completed, check all the bolts, screws and fastners to confirm that they are securely fastened. R

2 TABLE OF CONTENTS [] SPECIFICATIONS... [] CLASSIFICATION... [] WIRING DIAGRAM -. Unit Mount & Ceiling Mount (AL-90/90) Track Mount Type (AL-90) Swing Mount Type (AL-90X)... INSTALLATION INSTRUCTIONS [] UNIT MOUNT TYPE (AL-90)... [] CEILING MOUNT TYPE (AL-90)... [] TRACK MOUNT TYPE (AL-90)... 8 [7] SWING MOUNT TYPE (AL-90X)... OPERATING INSTRUCTIONS [8] OPERATING INSTRUCTIONSONS... [9] ADJUSTING TENSION of BALANCE ARM... [0] CLEANING, MAINTENANCE PARTS & DISPOSAL... [] MAINTENANCE AND INSPECTION...

3 Intended Use of the Product This product is intended for the exclusive use for diagnoses, treatments and relative procedures of dentistry, and must be operated or handled by the qualified dentists or by dental staffs under the supervision of the dentist. Such dentists or dental staffs should instruct and/or assist the patients to approach to and leave from the product. Patients should not be allowed to operate or handle the product unless he/she is so instructed. WARNING Operation of a dental light under Electro Magnetic Interferences. This equipment may malfunction by electromagnetic interferences. Do not install dental light close to the equipment that generates electromagnetic interference (i.e. communication equipment, elevator) Do not use the device that creates interference (i.e. cellular phone) near this equipment. Do not use electric surgical knife or laser knife with dental light. Light may turns on/off by itself due to malfunction of a sensor caused by electromagnetic interferences. Symbols Caution It means caution, warnings, or possibility to danger. Manufacturer Environmental condition for Operation Temperature : ~0F ( ~ 0 ) Humidity : 0 ~ 80% Pressure : 8.7~. psi (00 ~ 00 hpa) Environmental condition for Storage Temperature : -~8F ( -0 ~ 70 ) Humidity : 0 ~ 80% Pressure : 8.7~. psi (00 ~ 00 hpa) Environmental condition for Transportation Temperature : -~8F (-0 ~ 70 ) Humidity : 0 ~ 80% Pressure : 8.7~. psi (00 ~ 00 hpa)

4 WARNING To avoid the risk of electric shock, this equipment must only be connected to supply mains with protective earth. Position a light head by holding light handle(s). Installation and service work should be conducted by an authorized installation/service personnel only. WARNING: The followings are prohibited. To modify this equipment. To use the equipment under any failure condition. To use the equipment without doing the daily and periodical check-up. To wipe the plastic covers with any disinfectant or detergent that contains organic solvent. Precautions for Installation Assure that the ceiling and/or framing can provide the 70 lb. (.kg) of dead weight capacity and the additional force of movement and positioning of the light. Keep the equipment away from water. Keep in circumstances safe from influence by temperature, humidity, wind, sun light, air containing salts and minerals. Care about stability such as inclination, vibration and impact, including handling and transportation. Do not keep the equipment in a place where chemicals are or where gas is emitted. During lifting and unpacking of the light, make sure to hold only the designated parts. Do not drop or hit the light. Do not connect to power supply other than AC0V 0HZ. Ground light properly prior to turning power on. When the installation process has been completed, verify that all the mechanical and electrical functions are working properly. Thick gloves are highly recommended at unpacking. Do not modify this equipment.

5 CAUTION Before use Check connection of switches and make sure that the device functions properly. Make sure that grounding wire is connected. Make sure that cables are properly and perfectly connected. During use Do not use the light longer than required for examination or treatment. Always watch the patient and the equipment to make sure nothing is wrong. If anything wrong is observed with the equipment or the patient, take a proper action, such as stopping the use of equipment as well as keeping the patient in safe. Keep an eye on the patient not to touch the equipment. After use Turn off the light. Clean the equipment and get it ready for use. CAUTION Do not spray liquids directly onto light surfaces. In order to prevent damage to electrical components and systems, do not apply excess cleaning solution onto light surfaces. NOTE Warranty does not cover damage to equipment caused by disinfectant solutions [] SPECIFICATIONS. Focal Distance...." (0 mm). Color Temperature Kelvin. Light Intensity Regular Operation Mode Lux / 70 FTC ~ 000 Lux / 970 FTC Composite Mode Lux / 0 FTC. Light Pattern...." x." at.". Power Requirement... AC. 0V / 0 Hz / 0.A [] CLASSIFICATION a. Protection against electric shock : Class I Equipment. b. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide. - -

6 - - Power cable (00, SJT) CADQ7** Terminal Block Light / Earth line CADQ7** Remarks Connector Symbol SM... SM Connector XA... XA Connector dot Plug / The side with black dot has male pins Receptacle SENSOR Noise filter section(al-90) A08AH** Earth line for power PCB. A07X8** Trunk line for power PCB. -Fuse A087M** 0V/0.8A(T) Power Switch Lead wire() 0MM CACP77** Lead wire()00mm CACP7** Sensor/Manual Mode Selection Switch A087L** Bright Pink Light MANUAL Ferrite (Four turns) LED: Power LED LED: Sensor Signal LED SW VR lower limit setting SW Manual SW for operation test Settings of PCB dip switches ( SW,) and jumper pin (JP). SW N AC0V Power Input L PWM input GND Pink Bright Light PWM output CN NHP CN0 NHP CN0 VHP CN XHP CN0 XHP LED Light Power PCB. (G08U**) DCV Power input DCV Power input White White CN0 XHP LED Light Control PCB. (G0A0**) LED output A LED output A LED output K LED output K A08X** CN XAP CN9 NHP Setting condition Test mode ( Always ) Off: Normal operation, On: Test operation Transition time to Composite mode (by a sensor) Off: second, On: seconds Wake-up brightness setting from light off condition. Off :. Composite Mode when a light is turned on by using a sensor. :. Keeps on getting on/off signal from dr table, light stays in composite mode. On :. Regular Mode when a light is turned on by using a sensor. :. Keeps on getting on/off signal from dr table, light goes into regular mode. Combining dental unit Off: Clair unit, On: CP-One plus Trunk line for Control PCB.power Sensor power output Sensor input CN XHP GND DCV power output Display LED output /White /White DCV power output VR input 9 Lead wire for inside arm (AL-90/90) A087K** Default setting ON ON CN PHP SW SW JP VR input DCV power input VR output DCV power input Display LED input 7 8 /White /White Display LED PCB. (G07Z**) DCV output CN XAP XAP XAP Trunk line for LED module(head) A07MA** /White /White Trunk line for LED sensor PCB A07MB** Intensity adjustment Volume Section A07M9** Setting condition Sensor activation setting Off: Activate when a hand goes away, On: Activate when a hand comes in. Includes Composite Mode Off:Yes, On: No Speed setting of communication line Off: 800bps, On: 00bps LED blink setting of Composite Mode Off: Slow blinking, On: Rapid blinking PC side: Clair Unit, side: CP-One plus PC side: Clair Unit, side: CP-One plus 0KB (VR) Intensity adjustment /White /White SMP() Head Section PC PC SMP() LED module LED Module Assy. G07U** Sensor power input Sensor output GND Default setting LED module LED Sensor PCB. (G080**) CN EHP -. Unit Mount (AL-90) & Ceiling Mount (AL-90) [] WIRING DIAGRAM Power Supply Box Section Arm Section York Section

7 - - Power cable (00mm) CAMV0** Terminal Block Light Earth line 00mm A087N** Remarks Connector Symbol SM... SM Connector XA... XA Connector XM... XM Connector dot Plug / / The side with black dot has male pins Receptacle SENSOR MANUAL A08AJ** Noise filter section(al-90) Earth line for power PCB. A07X8** Trunk line for power PCB. -Fuse A087M** 0V/0.8A(T) Power Switch Lead wire() 0MM CACP77** Lead wire()0mm CACP7** Sensor/Manual Mode Selection Switch A087L** Bright Pink Light Ferrite (Four turns) LED: Power LED LED: SW SW N AC0V Power Input L Sensor Signal LED VR lower limit setting Manual SW for operation test PWM input SW Pink Bright PWM output Settings of PCB dip switches ( SW,) and jumper pin (JP). Light GND CN NHP CN0 NHP CN0 VHP CN XHP CN0 XHP LED Light Power PCB. (G08U**) DCV Power input DCV Power input + - White White + - CN0 XHP LED output A LED output A LED output K LED output K CN XAP CN9 NHP Trunk line for Control PCB. power A08X** CN XHP /White /White Sensor power output Sensor input Trunk line for LED module A087P** Trunk line for Signal A087Q** GND DCV power output Display LED output Setting condition Test mode (Always ) Off: Normal operation, On: Test operation Transition time to Composite mode (by a sensor) Off: second, On: seconds Wake-up brightness setting from light off condition. Off :. Composite Mode when a light is turned on by using a sensor. :. Keeps on getting on/off signal from dr table, light stays in composite mode. On :. Regular Mode when a light is turned on by using a sensor. :. Keeps on getting on/off signal from dr table, light goes into regular mode. Combining dental unit Off: Clair unit, On: CP-One plus LED Light Control PCB. (G0A0**) DCV power output VR input 9 XMP 7 XA7P /White /White Trunk line A for power supply box A087R** XMP 7 XA7P Default setting ON ON /White /White XMP Trunk line C for power supply box (Pole size 8. ~ 0F) A087T** 7 XA7P SW SW JP 7 8 /White A087S** /White /White /White XAP XAP Trunk line for LED module(head) A07MA** CN PHP /White /White Trunk line for LED sensor PCB A07MB** Display LED PCB. (G07Z**) DCV output VR input DCV power input VR output DCV power input Display LED input Trunk line B for power supply box Setting condition Sensor activation setting Off: Activate when a hand goes away, On: Activate when a hand comes in. Includes Composite Mode Off:Yes, On: No Speed setting of communication line Off: 800bps, On: 00bps LED blink setting of Composite Mode Off: Slow blinking, On: Rapid blinking PC side: Clair Unit, side: CP-One plus PC side: Clair Unit, side: CP-One plus CN XAP /White /White SMP() A07M9** 0KB SMP() LED module Intensity adjustment Volume Section York Section LED module LED Module Assy. G07U** Sensor power input Sensor output GND (VR) Intensity adjustment Default setting PC PC LED Sensor PCB. (G080**) CN EHP Head Section -. Track Mount (AL-90) Power Supply Box Section

8 - - A0D** Remarks Connector Symbol SM... SM Connector XA... XA Connector XM... XM Connector dot The side with black dot has male pins Plug Power supply cable 000L Light / Earth line (70M) CADQ7** / Receptacle A08AJ** -Fuse 0V/0.8A(T) Noise filter section (AL-90) Power supply box Section Earth line for power PCB. A07X8** A08CG** Trunk line for fuse-air sw (N) (90X) A08CF** Trunk line for air sw - power pcb. Trunk line for fuse-air sw (L) (90X) A08CE** SW N AC0V Air Switch Power Input L Settings of PCB dip switches ( SW,) and jumper pin (JP). CN0 VHP LED Light Power PCB. (DL-900) (G08U**) CN0 XHP CN0 XHP CN0 NHP LED output A LED output A LED output K LED output K DCV Power output PWM input Setting condition Test mode ( Always ) Off: Normal operation, On: Test operation Transition time to Composite mode (by a sensor) Off: second, On: seconds Wake-up brightness setting from light off condition. Off :. Composite Mode when a light is turned on by using a sensor. :. Keeps on getting on/off signal from dr table, light stays in composite mode. On :. Regular Mode when a light is turned on by using a sensor. :. Keeps on getting on/off signal from dr table, light goes into regular mode. Combining dental unit Off: Clair unit, On: CP-One plus - + GND power pcb. signal line (AL-90Q) A08CH** 7 8 XA8P Default setting ON ON XMP /White /White SW SW JP 7 8 Setting condition Default setting Sensor activation setting Off: Activate when a hand goes away, On: Activate when a hand comes in. Includes Composite Mode Off:Yes, On: No Speed setting of communication line Off: 800bps, On: 00bps LED blink setting of Composite Mode Off: Slow blinking, On: Rapid blinking PC side: Clair Unit, side: CP-One plus PC PC side: Clair Unit, side: CP-One plus /White /White Trunk line for LED module(head) A07MA** XAP /White /White /White /White SMP() LED module SMP() LED module LED Module Assy. G07U** PC -. Swing Mount (AL-90X) SENSOR MANUAL A089U** Lead wire line for S/M select sw (with sw.) Bright Pink Light LED: Power LED LED: SW SW Sensor Signal LED VR lower limit setting Manual SW for operation test Ferrite Four turns Light PWM output CN NHP DCV Power input White + - CN XHP LED Light Control PCB. (G0A0**) CN XAP CN9 NHP White Pink Bright Sensor power output Sensor input DCV power output VR input DCV power output Display LED output CN XHP GND XAP 9 Trunk line for AL-90X (inside duct hose) A089V** A089T** Inside arm lead wire (AL-90Q) XAP Trunk line for LED sensor PCB A07MB** Display LED PCB.(DL-900) (G07Z**) CN DCV output PHP VR input DCV power input CN VR output DCV power input XAP Display LED input Sensor power input Sensor output GND Intensity adjustment Volume Section A07M9** 0KB (VR) Intensity adjustment York Section LED Sensor PCB. (G080**) CN EHP Head Section Switch box Section

9 º 90º INSTALLATION INSTRUCTIONS [] UNIT MOUNT TYPE (AL-90) -. Dimensions -/ () -/ (90) 0-7/8 (0) -/ (.) 8-7/ (.) 90º 9º -/ (0) -/ () º -9/ (9) -/8 () -/ (88.) -/ () 8-/ (0) -/ () -/ () 8-/ (78) -/(9) -7/8 (98) -7/ () -/ (.7) 0º 0º -/ (8) -7/ () 9-/8 (8.) 0-7/ () 0º -. Installation Instructions * All necessary parts are included in the box. M x Painted Screw... pcs. M x 0 Painted Screw... pcs. Yoke Cover... pce. ) Install the light head to the balance arm with M x 0 painted screws. M X 0 Painted Screw Balance Arm Light Head ) Connect the wire harness P connector : yellow / green / blue P connector : black / black & white / brown / brown & white Same color to be met at each side of connector P connector : red / orange / purple / gray connec to LED Light display PCB of yoke cover. Yoke Cover P Connector LED Light Display PCB. P Connector P Connector ) Attach the yoke cover with M x painted screws. M X Painted Screw - -

10 90º [] CEILING MOUNT TYPE (AL-90) -. Dimensions -/ () -/ () -/ (90) 0-7/8 (0) -/ (.) 8-7/ (.) 9º º 90º -/ () -9/ (9) -/ () -/ (88.) 8-/ (0) -/ (.7) 0º -/ () -/8 () 8-/ (78) -/(9) -7/8 (98) -7/ () 0º -/ (8) -7/ () º 9-/8 (8.) 0-7/ () -. Installation Instructions ) Secure mounting plate to the ceiling. ) Route the power supply through the center of the mounting plate. ) Install the leveling nuts between the mounting plate and the ceiling flange. ) Install the ceiling flange to the mounting plate with washers and nuts supplied. ) Insert the suspension tube into the ceiling flange and secure it with roll pin and set screws supplied. ) Be sure the suspension tube is plumb. 7) Slide the flange cover and flange cover ring (flat side up) over the suspension tube and secure them about half way up the tube. Use only one set screw as you will be moving this on final installation. 8) Install the light assembly to the suspension tube running the wire cord up through the tube to the ceiling flange. Secure it with Allen set screws. 9) Connect the incoming power to the wire cord from the light assembly. Be sure to follow the local electrical codes. 0) Test the light for proper operation. ) Reposition the flange cover and secure it with the flange cover ring - Secure all set screws. 0º -/ (0) () Power Supply Cable () Mounting Plate () Leveling Nut () Washer () Nut () Ceiling Flange (7) Socket Screw for Flange (8) Suspension Tube (9) Roll Pin (0) Socket Screw for Arm () Flange Cover () Cover Ring () Socket Screw for Ring () Suspension Tube of Arm - -

11 FULL-SIZE MOUNTING TEMPLATE "-/ (REF) "-/ (REF) "-9/ (REF) 7/" Mounting Holes - 7 -

12 [] TRACK MOUNT LIGHT (AL-90) -. Dimensions 77-9/ (970) 7-/ (0) 8-/ (7) (80) for 00 mm ceiling height 9. (000) for 000 mm ceiling height 9-/ (00) - MAX 8 (000) 0º 0 -/ (0) -/8 () 9-/ (7) 90º 90º -. Ceiling Preparation For safety in operation as well as stability of the light source, the importance of proper ceiling structure cannot be overemphasized. In general, a ceiling structure capable of supporting 00 lb. dead weight is required. A) In conventional ceilings with joists perpendicular to the center line of the light, attach the pallet by at least - / x " lag screws. Suitable holes are provided in pallet for most installations, utilizing " or " cc ceiling joists. For other spacings or locations, additional holes can be cut in pallet. (SEE FIGURE.) IMPORTANT:Locate transformer end of track at headrest end of chair. - Not legrest. B) For conventional ceilings with joists parallel to the center line of the light, cross blocks must be installed in places to allow mounting with at least - / x " lag screws. (SEE FIGURE.) C) For suspended ceilings, appropriate rigid structure must be attached to the ceiling framework to provide 00 lb. dead weight capacity. (SEE FIGURE.) 0º º -/ (0) 9-/8 (8.) 0-7/ () Electrical Feed Opening Transformer End Used for " Center to Center Joists Used for " Center to Center Joists FIGURE / x Lag Bolts () - 8 -

13 CEILING PREPARATION Crossblocks Places " Center to Center FIGURE FIGURE - 9 -

14 -. Electrical Preparation Refer to FIGURE for the location of electrical feed opening in pallet, provide wire, 0V, 0Hz circuit ( amp. fuse or breaker) through flexible conduit with enough slack to protrude at least " below the pallet when installed. Terminate the conduit with /" body box connector suitable for mounting through / thickness. A readily accessible shut-off switch for this circuit is recommended. Use wiring suitable for 90 C service. Head of Chair "-/8 DIA (Electrical Feed Opening) "-/ /8" DIA HOLE " DIA C'Bore (8Holes) "-/ " "-/8 "-/ " 8" " /" FIGURE -. Installation Instructions ) Lead out the power supply cable from the ceiling where the track light is mounted. ) Run the power supply cable through the pallet and mount the pallet. ) Place track against the pallet and slightly engage two mounting bolts at the end opposite to the electrical opening. ) Allowing the free end to hang down slightly for access, install the conduit box connector to the track. ) Finish bolting the track securely to the pallet. ) Connect the wires from the feed to the terminal block. 7) Slide the trolley onto the track (end near electrical opening) with the arrow on the trolley oriented toward the pulley on the track. 8) Carefully guide the wire from the trolley, around the spring-loaded pulley and back toward the end of track. 9) Attach retainer clamp to small screw in track. Clip the free end of the trolley wire into the plastic clip near end. 0) Install rubber bumpers at the end of the track in the holes provided. Transformer Box Install Rubber Bumpers after Trolley Plastic Wire Clip Z Clip (Holds Bottom Cover) To Trolley Rubber Bumpers Connector Light / Electrical Feed Terminal Block Clamp (Factory Installed on Wire) Pulley End Cap - 0 -

15 ) Check operation of the trolley. It is factory adjusted to provide smooth effortless travel, without play; however rollers can be readjusted if necessary. Loosen the set screw and adjust the socket cap screw to vary roller clearance. Trolley Rollers Adjustment Screw Set Screw ) Unpack the transformer / housing assembly and mount it to the track with screws provided. ) Attach the pigtail leads to the corresponding power line wires at the terminal block. Retain the wires under the plastic clip. ) Connect the plug-in connector to the trolley wire. ) Carefully slide bottom cover onto the track from free end. Be sure to engage lip onto Z bracket. ) Install the end-cap with the screws provided. 7) Slide the trolley back and forth, checking for binding or rubbing. 8) Confirm that the swing arm is properly adjusted to stay where it is placed. If necessary, move the head up or down to expose the appropriate cross drilled nut and adjust with the tool provided. 9) Turn on power and check electrical operation of the light. () Power supply cable () Pallet 9 0 () Track () End-cup () Trolley () Power Supply Box (7) Light Assembly 8 DSL 7 (8) Bottom Cover (9) Rubber bumper (0) Screw with plain washer & spring washer Mx( pcs) () Hex Head Bolt M8x( pcs) () Spring Washer M8 ( pcs) This bracket is on the rear side of the cover [7] SWING MOUNT LIGHT (AL-90X) Wiring diagram and installation instractions, See the section in Dental Unit installation manual. - -

16 [8] OPERATING INSTRUCTIONS 8-. Major Parts Identification () LED Light Head () Sensor Switch () Intensity Control Volume () Balance Arm () Swing Arm () Power Supply Box 8-. Main Switch Turn on the main switch to the side marked with ' I '. Power on : ' I ' Mark Power off : ' ' Mark Main Switch Mode Selection Switch Unit & Ceiling Type 8-. Mode Selection Switch Switching modes can be changed by this switch. This switch is located on power supply box. Sensor : Touch-less ON/ and composite mode Manual : Manual Mode (ON only) Fuse Track Type Main Switch 8-. Touch-less Switch The light can be turned on/off with a touch-less sensor switch. The intensities are regular operation mode and composite mode. Fuse Mode Selection Switch 8--. Confirmation of mode selection switch Make sure that the mode selection switch is at sensor mode. LED Display 8--. Turning on/off The touch-less switch has a sensor. The sensor activates within the distance of -/" from the surface. Let your hand pass by within -/" from the touch-less sensor to turn on the light. Let your hand pass by again to turn off. Intensity Volume Control Active distance within -/ Touch-less Sensor Switch - -

17 8--. Switching to the composite mode During normal treatment mode, while the light is on, place and hold your hand within -/" from the touch-less sensor for seconds. The light intensity will be automatically reduced to the composite mode which has intensity of 00 lux. LED display under yoke blinks green on at composite mode. To switch back to the normal treatment mode, place your hand by the touch-less sensor seconds again. COMPOSITE Mode INTENSITY LED Display 00 Lux Blink Note: by placing your hand for seconds when the light is off. The light does not lit in the composite mode, but lit in normal treatment mode. Please make sure that the light is on before lighting in composite mode. 8-. Selection of intensity for normal treatment mode LED display under yoke turns green on at regular operation mode. By turning intensity control volume, you can adjust intensity steplessly between Lux. Intensity Control Volume Low LED Display High Note: If light intensity is set below 0 FTC and in composite mode, light will Flash briefly when exiting composite mode. This is a normal condition indicating return to standard mode. [9] ADJUSTING TENSION of BALANCE ARM 9-. Adjustment of the tension of the balance arm Position the angle of the balance arm so the tension adjustment nut becomes visible just under slot A. Turn the nut and adjust the tension with the adjustment bar supplied with the light. Direction of rotation of the nut When the light head tends to go up, turn the nut to + direction. When the light head tends to go down, turn the nut to direction. Adjustment Bar Hole C (Socket Screw) Slot A (for tension) Slot B (for angle) - -

18 9- Adjustment of the angle of the light head ) Use a mm hex key wrench to loosen socket screw in front of Hole C. ) Position the angle of the balance arm so the head angle adjustment nut becomes visible just under the slot B. Turn the nut and adjust the tension with the adjustment bar supplied with the light. Hole C When the light head tilts upward, turn the nut to + direction. When the light head tilts downward, turn the nut to - direction. ) After adjustment is done, re-tighten the socket screw. Note : Unless this socket screw is re-tightened, the angle of the head will be changed during use. [0] CLEANING,MAINTENANCE PARTS & DISPOSAL 0-. Cleaning CAUTION Allow light to cool prior to cleaning. Use a soft cloth or cotton only to gently clean surfaces. Use of other materials can scratch and damage surfaces. Covers can be cleaned with a soft cloth or cotton moistened with alcohol. The reflector can be cleaned with a soft and dry cloth or cotton with extreme care. 0-. Maintenance Parts Fuse are maintenance parts. Period for repair and supplying parts We will supply parts of the equipment for 0 years, after the manufacturing of this equipment is discontinued. 0-. Lifetime Provided that the recommended and authorized care and maintenance are correctly performed, the working lifetime of this equipment is 0 years from the date of initial shipment from the manufacturer. 0-. Disposal This is not an infectious device, but prior to disposal make sure that no parts of the device is infected. Follow the federal, state and local regulations for disposal. - -

19 [] MAINTENANCE AND INSPECTION Guide for daily maintenance and inspection (Maintenance and inspection by user) Management of maintenance and inspection of medical equipment should be implemented by the user (medical inspection). In case the user does not implement such management, it is permitted that such management is outsourced to a qualified entity such as a medical equipment repair company. For safe use of this product, it is necessary that inspection should be conducted in the specified frequency on the items described below. - -

20 NOTE R BELMONT EQUIPMENT, Division of Takara Belmont USA, Inc. 0 Belmont Drive Somerset, New Jersey 0887 U.S.A. TEL.:(7) / (800) -9 Fax.:(7)-0 TAKARA CO, CANADA LTD. 07 S. Sheridan Way, Mississauga, Ont., LJM, Can. TEL.:(90) 8-7 Fax.:(90)8-0 TAKARA BELMONT CORPORATION (Manufacturer) -, -Chome, Higashi-shinsaibashi,Chuo-ku,Osaka,Japan TEL.: FAX.: Book No. E0FAB0 Printed in Japan 0-0