Thank you very much for purchasing Pro skit MT-7063 & MT-7064 PoE & Lan cable tester. This product is ideal for testing live Ethernet cables and deter

Size: px

Start display at page:

Download "Thank you very much for purchasing Pro skit MT-7063 & MT-7064 PoE & Lan cable tester. This product is ideal for testing live Ethernet cables and deter"

寄郁
6 years ago
Views:

1 MT-7063/MT-7064 PoE & Lan Cable Tester User s Manual 1 st Edition, Prokit s Industries Co., Ltd

2 Thank you very much for purchasing Pro skit MT-7063 & MT-7064 PoE & Lan cable tester. This product is ideal for testing live Ethernet cables and determining continuity of network and telephone cables. Features : PoE Tester Easily tests Ethernet network for Power over Ethernet existence Quickly identifies the type of Power Sourcing Equipment (either Endspan or Midspan) MT-7063 is an economical type only for detecting Midspan/Endspan. MT-7064 is an advanced type that can easily identify IEEE af/at PoE standard and Midspan/Endspan Cable Tester Checks RJ11/RJ12/RJ45 pin to pin cable maps Automatically runs all tests and checks for continuity, opens, shorts and crossover wire pairs Cable mapping up to 300M SPECIFICATION : Model number MT-7063 MT-7064 Max. distance of cable map 300M Compatible connectors RJ45(8 pin) & RJ11(6P/6C/4C/2C) & RJ12 & POE RJ45 Lan cable Cat 5 5e 6(UTP/STP) Cable types tested RJ11/12 Telephone Cable Cat 3 (6P/2C/4C/6C) Cable map indication 8 LED,Fast/Slow dual speed Shielded indication YES PoE indication(master:) Midspan/Endspan af/at PoE standard and Midspan/Endspan Live telecommunication equipment test and router test Yes Dimension (L W D) Master: mm Remote: mm Battery type DC 9.0V (not included) Weight 130g(Not included battery) SAFETY INSTRUCTIONS Please read and learn the safety instructions before using or maintaining the equipment 1

3 This cable tester can't test any electrified product. Please change the batteries if and weak lights appears. Please verify the RJ45 connector and cable is good and properly inserted into jack. If not properly installed, the tester may not work. Please use quality tools to crimp the cables. Take out the battery if the tester will not be used for a long time. PoE Tester The 802.3af/802.3at PoE Tester, connected to an RJ45 outlet, allows one to test live Ethernet cables and determine if power and data are present. And also identifies the type of Power Sourcing Equipment (either Endspan or Midspan) in your network. This unit is an easy-to-use in Power over Ethernet(PoE) adapters for professionals, businesses and home users to determine the existence of Power over Ethernet. Operation (MT-7063) 1. Connect one end of cable into RJ45 Port of PoE equipment, and the other end plug into the PoE jack of MT Turn on the power of PoE equipment, and then switch on the PoE tester. 3. When LED1 light turns orange as below, it means power is provided by Midspan (45/78) 4. When LED2 light turns green as below, it means power is provided by Endspan (12/36). 5. When LED1 light turns orange, and also LED2 light turns green as below, it means power is provided by Midspan & Endspan (4 pair). Midspan (orange) Endspan(green) Result V X Minspan(45/78) X V Endspan(12/36) V V 4 pairs (1236& 4578) Operation (MT-7064) 1. Connect one end of cable into RJ45 Port of PoE equipment, and the other end into the PoE port of MT Power on the PoE equipment, and then switch on the MT Test result 1: When LED1 light turns green as below, it means power is provided by Endspan (12/36), and it is 802.3af standard, the output power is 15.4W. (PD Max 12.95W) Test result 2: When LED1 light turns green and LED2 light turns blue as below, it means power is provided by Endspan (12/36), and it is 802.3at standard, the output power is 30W. (PD Max 25.5W) 2

4 Test result 3: When LED3 light turns green as below, it means power is provided by Midspan(45/78), and it is 802.3af standard, the output power is 15.4W. ( PD Max 12.95W) Test result 4: When LED3 light turns green and LED4 light turns blue as below, it means power is provided by Midspan (45/78), and it is 802.3at standard, the output power is 30W. (PD Max 25.5W) Test result 5: When the LED1 & LED3 both turn green, it means power provided by Midspan & Endspan (4 pairs), and it is 802.3af standard, the output power is 30W. Test result 6: When the 4 LEDs are on, it means power provided by Midspan & Endspan (4 pairs), and it is 802.3at standard, the output power is 60W. D1(green) D2(blue) D3(green) D4(blue) Result Endspan(1236) V X X X 802.3af (over Data) Endspan(1236) V V X X 802.3af (over Data) Midspan(4578) X X V X 802.3af(over Spare) Midspan(4578) X X V V 802.3at(over Spare) V X V X 802.3af (4 pairs) V V V V 802.3at (4 pairs) Cable Tester Functions 1. It can test corresponding double-twisted cable 1,2,3,4,5,6,7,8 and G. Meanwhile, it can identify good connection, shorts, crossover or opens. 2. "OFF" means Power off, "ON" means normal scan, "SLOW" means slow scan. Operation Slide the power switch to on (Normal grade) position or "S" (Slow grade) position, and then connect the RJ45 /RJ11/RJ12 cable with Master Tester and Remote Tester. The cable mapping will be automatically processed by pin to pin scanning as below: Pin 1-8 8P/8C Pin 1-6 6P/6C Pin 2-5 6P/4C Pin 3-4 6P/2C 3

5 Abnormal connections instruction OPENS 1. While performing the pin to pin scanning, if the pin 3 LED does not light up on both the master unit and remote unit, it means Pin 3 is open circuited. 2. If there are several pins that are not connected, there are several lights that will not turn on. If less than two pins are connected, none of the lights are on. CROSSOVER If pins are crossover, for example NO2 and NO4,the result is displayed as below: Master Tester: G Remote Tester: G SHORT If two or more pins are short circuited, the lights will not light up on the remote tester while master tester shows normal. Testing patch cables or wall installed cables, two cables which can match each other (eg 110P4-RJ45) will be connected to the tester. Test by RJ45 cable Slide the power switch to "ON" or "SLOW", the power will turn on. 1. UTP cable test Connect the cable, the tester will pin to pin scan sequentially from 1 to 8 circulate test. 2. STP cable test Connect the cable, the tester will pin to pin scan sequentially from 1 to G circulate test. If any cable is open, short or crossover, the result is as shown as above. When finished testing, turn off the tester. If finished for a long time, remove the battery for storage. Test by RJ11/RJ12 Slide the power switch to "ON" or "SLOW", the power will turn on. 1. RJ11 cable test Connect the cable, the tester will pin to pin scan sequentially from 2 to 5 circulate test. 2. RJ12 cable test Connect the cable, the tester will pin to pin scan sequentially from 2 to 6 circulate test. If any cable is open, short or crossover, the result is as shown as above. When finished test, turn off the tester. If finished for a long time, remove the battery for storage. 4

6 MT-7063/MT-7064 PoE& 網路線纜測試器一產品介紹 : MT-7063/MT-7064 是一款集多種線路測試及 PoE 測試於一體的多功能纜線測試器, 可測試的線材種類 RJ-45 RJ-11 RJ-12 的斷路短路交錯, 還可用來測試網線是否供電及供電情況, 並能區分 POE 交換機的標準, 即 802.3AF 和 802.3AT 兩種標準, 廣泛應用於商業, 家用等領域二安全注意事項 : 1. 使用前請細詳閱讀使用說明書, 錯誤使用可能造成測試器損壞 2. 此測試器不能用於測試帶有電壓之活線, 若將活線接於此測試器, 將嚴重燒壞本設備 3. 本設備採用 9V 電池供電, 若發生亮度減弱情況, 請及時更換電池 ; 4. RJ45 接頭銅夾片沒完全壓下去時不能測試, 否則會使埠永久損壞 ; 5. 長時間不使用本設備時, 請將電池取出, 以防日久後電池液漏出 6. 使用時請勿將機殼打開使用或自行更換內部零件, 如此可能造成測試器損壞三產品特色 : 1. 快速結果測試 ( 斷路. 交叉. 直通. 短路 ) 2. 快速判斷交換機供電類型及供電情況 ; 3. 支援 802.3AF 和 802.3AT 兩種標準 ; 4. 網線埠設計, 方便測試 ; 5

7 5. 人性化設計, 廣泛用於綜合佈線技術人員 6. 明亮清楚的 LED 燈顯示四產品規格 : 規格 MT-7063 MT-7064 線序 / 對應故障最大測量距離可測試連結阜適用電纜線 300m RJ45(8 pin) & RJ11(6P/6C/4C/2C) & RJ12 & PoE RJ45 網路線 Cat 5 5e 6(UTP/STP) RJ11/12 電話線 Cat 3 (6P/2C/4C/6C) 線序 / 故障指示 8 LED, 快 / 慢雙速測試屏蔽指示 PoE 指示電信設備和路由器活電測試 2 LED ( 中間 / 末端跨接法 ) 有有 4 LED ( 中間 / 末端跨接法, at /af PoE 電源環境 ) 尺寸 (L W D) 主機 mm, 遠端 mm 電源 DC 9.0V ( 出貨不含 ) 重量 130g( 不含電池 ) 五線材及 PoE 的測試方法注意 : 對線時, 測試器的測試結果皆需搭配遠端接收器亮燈順序來判斷線路正確性 PoE 測試 : MT-7063: 6

8 1. 將主測試器妥善連接 RJ45(8P/8C) 網路線或插座另一端連接在正在工作的網路交換機上 2. 當 Midspan 橙色 LED 燈亮起時, 說明該埠中 45/78 線纜供電 ; 3. 當 Endspan 綠色 LED 燈亮起時, 說明該埠中 12/36 線纜供電 4. 當 Midspan 橙色和 Endspan 綠色的燈同時亮的時候, 說明該埠中 12/36/45/78 線纜同時供電 Midspan Endspan 結果顯示 ( 橙色 LED) ( 綠色 LED) V X 45/78 線纜同時供電 X V 12/36 線纜同時供電 V V 12/36/45/78 四組線纜同時供電 MT-7064: 1. 將主測試器妥善連接 RJ45(8P/8C) 網路線或插座另一端連接在正在工作的網路交換機上 2. 當 D1 綠色指示燈亮起, 說明該埠 12/36 線纜同時供電, 其交換機類型是 802.3AF 標準, 輸出功率是 15.4 瓦 (PD 埠最大功率瓦 ); 3. 當 D1 綠色指示燈 & D2 號藍色指示燈亮起, 說明該埠 12/36 線纜同時供電, 交換機類型是 802.3AT 標準, 輸出功率是 30 瓦 (PD 埠最大功率 25.5 瓦 ) 4. 當 D3 綠色指示燈亮起, 說明該埠 45/78 線纜供電, 其交換機是 802.3AF 標準, 輸出功率是 15.4 瓦 (PD 埠最大功率瓦 ); 5. 當 D3 綠色指示燈 & D4 號藍色指示燈亮起時, 說明該埠 45/78 線纜供電, 其交換機類型是 802.3AT 標準, 輸出功率是 30 瓦 (PD 埠最大功率 25.5 瓦 ) 6. 當 D1&D3 號燈指示燈同時亮起時, 說明該埠 12/36/45/78 線纜同時供電, 其供電類型是 802.3AF 標準, 輸出功率是 30 瓦 ; 1) 當 D1&D2&D3&D4 指示燈同時亮起時, 說明 12/36/45/78 線纜同時供電, 7

9 其供電類型是 802.3AT 標準, 輸出功率是 60 瓦 ; D1 綠色 LED D2 藍色 LED D3 綠色 LED D4 藍色 LED 顯示結果 V X X X 12/36 線纜供電,802.3af 標準 V V X X 12/36 線纜供電,802.3at 標準 X X V X 45/78 線纜供電,802.3af 標準 X X V V 45/78 線纜供電,802.3at 標準 V X V X 12/36/45/78 線纜供電,802.3af 標準 V V V V 12/36/45/78 線纜供電,802.3at 標準 1. 測試 RJ45 網路線 : 將所需測試線插入主測試器和遠端測試器 RJ45 埠, 撥動主機開關至 ON 或 SLOW 此時,POWER 燈亮起, 線對表中對應的 1~8/G 燈開始掃描 ( 如果是 STP 線則 "G" 燈也會亮 ) 通路的 LED 燈號顯示 : 主測試器和遠端測試器 1~8/G 指示燈按先後順序依次同步點亮短路的 LED 燈號顯示 : 主測試器 1~8/G 指示燈按先後順序依次點亮, 遠端測試器 1~8/G 指示燈對應短路位置燈不亮, 其他燈按先後順序依次點亮斷路的 LED 燈號顯示 : 主測試器和遠端測試器指示燈對應斷路位置 LED 燈不亮, 其他燈按先後順序依次同步點亮交叉的 LED 燈號顯示 : 主測試器 1~8/G 指示燈按先後順序依次點亮, 遠端測試器 1~8/G 指示燈按實際壓接錯位順序依次點亮 2. 測試 RJ-11/12 電話線 : 將所需測試線插入主測試器和遠端測試器 RJ11 埠, 撥動主機開關至 ON 或 SLOW 此時,POWER 燈亮起, 如果 6 芯電話線則 LED 亮 1~6 號燈 ",4 芯 8

10 電話線亮 2~5 號燈 ",2 芯電話線亮 3~4 號燈 3. 工作中的網路檢測 : 注意 : 此測試方法只能測試網線路通斷, 不能檢測交叉或短路將主測試器妥善連接 RJ45(8P/8C) 網路線或插座另一端連接在正在工作的網路交換機上, 當主測試器上的 1~8 G 測試結果指示燈, 按先後順序逐一點亮時, 表示網路線 1~8 G 全部連通, 如有燈號未亮, 代表線路故障 9

11 MT-7063/MT-7064 PoE& 网络线缆测试器二产品介绍 : MT-7063/MT-7064 是一款集多种线路测试及 PoE 测试于一体的多功能缆线测试器, 可测试的线材种類 RJ-45 RJ-11 RJ-12 的断路短路交错, 还可用来测试网线是否供电及供电情况, 并能区分 POE 交换机的标准, 即 802.3AF 和 802.3AT 两种标准, 广泛应用于商业, 家用等领域五安全注意事项 : 7. 使用前请细详阅读使用说明书, 错误使用可能造成测试器损坏 8. 此测试器不能用于测试带有电压之活线, 若将活线接于此测试器, 将严重烧坏本设备 9. 本设备采用 9V 电池供电, 若发生亮度减弱情况, 请及时更换电池 ; 10. RJ45 接头铜夹片没完全压下去时不能测试, 否则会使埠永久损坏 ; 11. 长时间不使用本设备时, 请将电池取出, 以防日久后电池液漏出 12. 使用时请勿将机壳打开使用或自行更换内部零件, 如此可能造成测试器损坏六产品特色 : 7. 快速结果测试 ( 断路. 交叉. 直通. 短路 ) 8. 快速判断交换机供电类型及供电情况 ; 9. 支持 802.3AF 和 802.3AT 两种标准 ; 10. 网线埠设计, 方便测试 ; 10

12 11. 人性化设计, 广泛用于综合布线技术人员 12. 明亮清楚的 LED 灯显示七产品规格 : 规格 MT-7063 MT-7064 线序 / 对应故障最大测量距离可测试连结阜 300m RJ45(8 pin) & RJ11(6P/6C/4C/2C) & RJ12 & PoE 适用电缆线线序 / 故障指示 RJ45 网络线 Cat 5 5e 6(UTP/STP) RJ11/12 电话线 Cat 3 (6P/2C/4C/6C) 8 LED, 快 / 慢双速测试屏蔽指示 PoE 指示电信设备和路由器活电测试 2 LED ( 中间 / 末端跨接法 ) 有有 4 LED ( 中间 / 末端跨接法, at /af PoE 电源环境 ) 尺寸 (L W D) 主机 mm, 远程 mm 电源 DC 9.0V ( 出货不含 ) 重量 130g( 不含电池 ) 五线材及 PoE 的测试方法注意 : 对线时, 测试器的测试结果皆需搭配远程接收器亮灯顺序來判断线路正确性 PoE 测试 : MT-7063: 11

13 5. 将主测试器妥善连接 RJ45(8P/8C) 网络线或插座另一端连接在正在工作的网络交换机上 6. 当 Midspan 橙色 LED 灯亮起时, 说明该埠中 45/78 线缆供电 ; 7. 当 Endspan 绿色 LED 灯亮起时, 说明该埠中 12/36 线缆供电 8. 当 Midspan 橙色和 Endspan 绿色的灯同时亮的时候, 说明该埠中 12/36/45/78 线缆同时供电 Midspan Endspan 结果显示 ( 橙色 LED) ( 绿色 LED) V X 45/78 线缆同时供电 X V 12/36 线缆同时供电 V V 12/36/45/78 四组线缆同时供电 MT-7064: 7. 将主测试器妥善连接 RJ45(8P/8C) 网络线或插座另一端连接在正在工作的网络交换机上 8. 当 D1 绿色指示灯亮起, 说明该埠 12/36 线缆同时供电, 其交换机类型是 802.3AF 标准, 输出功率是 15.4 瓦 (PD 埠最大功率瓦 ); 9. 当 D1 绿色指示灯 & D2 号蓝色指示灯亮起, 说明该埠 12/36 线缆同时供电, 交换机类型是 802.3AT 标准, 输出功率是 30 瓦 (PD 埠最大功率 25.5 瓦 ) 10. 当 D3 绿色指示灯亮起, 说明该埠 45/78 线缆供电, 其交换机是 802.3AF 标准, 输出功率是 15.4 瓦 (PD 埠最大功率瓦 ); 11. 当 D3 绿色指示灯 & D4 号蓝色指示灯亮起时, 说明该埠 45/78 线缆供电, 其交换机类型是 802.3AT 标准, 输出功率是 30 瓦 (PD 埠最大功率 25.5 瓦 ) 12. 当 D1&D3 号灯指示灯同时亮起时, 说明该埠 12/36/45/78 线缆同时供电, 其供电类型是 802.3AF 标准, 输出功率是 30 瓦 ; 2) 当 D1&D2&D3&D4 指示灯同时亮起时, 说明 12/36/45/78 线缆同时供电, 12

14 其供电类型是 802.3AT 标准, 输出功率是 60 瓦 ; D1 绿色 LED D2 蓝色 LED D3 绿色 LED D4 蓝色 LED 显示结果 V X X X 12/36 线缆供电,802.3af 标准 V V X X 12/36 线缆供电,802.3at 标准 X X V X 45/78 线缆供电,802.3af 标准 X X V V 45/78 线缆供电,802.3at 标准 V X V X 12/36/45/78 线缆供电,802.3af 标准 V V V V 12/36/45/78 线缆供电,802.3at 标准 1. 测试 RJ45 网络线 : 将所需测试线插入主测试器和远程测试器 RJ45 端口, 拨动主机开关至 ON 或 SLOW 此时,POWER 灯亮起, 线对表中对应的 1~8/G 灯开始扫描 ( 如果是 STP 线则 "G" 灯也会亮 ) 通路的 LED 灯号显示 : 主测试器和远程测试器 1~8/G 指示灯按先后顺序依次同步点亮短路的 LED 灯号显示 : 主测试器 1~8/G 指示灯按先后顺序依次点亮, 远程测试器 1~8/G 指示灯对应短路位置灯不亮, 其它灯按先后顺序依次点亮断路的 LED 灯号显示 : 主测试器和远程测试器指示灯对应断路位置 LED 灯不亮, 其它灯按先后顺序依次同步点亮交叉的 LED 灯号显示 : 主测试器 1~8/G 指示灯按先后顺序依次点亮, 远程测试器 1~8/G 指示灯按实际压接错位顺序依次点亮 2. 测试 RJ-11/12 电话线 : 将所需测试线插入主测试器和远程测试器 RJ11 端口, 拨动主机开关至 ON 或 SLOW 此时,POWER 灯亮起, 如果 6 芯电话线则 LED 亮 1~6 号灯 ",4 芯 13

15 电话线亮 2~5 号灯 ",2 芯电话线亮 3~4 号灯 3. 工作中的网络检测 : 注意 : 此测试方法只能测试网线路通断, 不能检测交叉或短路将主测试器妥善连接 RJ45(8P/8C) 网络线或插座另一端连接在正在工作的网络交换机上, 当主测试器上的 1~8 G 测试结果指示灯, 按先后顺序逐一点亮时, 表示网络线 1~8 G 全部连通, 如有灯号未亮, 代表线路故障 14

K301Q-D VRT中英文说明书141009

K301Q-D VRT中英文说明书141009 THE INSTALLING INSTRUCTION FOR CONCEALED TANK Important instuction:.. Please confirm the structure and shape before installing the toilet bowl. Meanwhile measure the exact size H between outfall and infall