角磨简介 本工具适用于金属或石材上打磨 打磨时不能使用水 请您在使用前务必仔细阅读说明书, 并严格按照说明书指示使用该角磨机 1. 操作控制 轴锁 2. 旋转方向 3. 输出轴 4. 非切割片护罩 5. 下法兰 6. 磨片 7. 上法兰 8. 扳

Transcription

1 型号 : CE CE 中国 GB 角向磨光机 Angle Grinder 各产品外观之间存在差异, 请以实物为准 专业电动工具 PROFESSIONAL TOOLS

2 角磨简介 本工具适用于金属或石材上打磨 打磨时不能使用水 请您在使用前务必仔细阅读说明书, 并严格按照说明书指示使用该角磨机 1. 操作控制 轴锁 2. 旋转方向 3. 输出轴 4. 非切割片护罩 5. 下法兰 6. 磨片 7. 上法兰 8. 扳手 9. 开关 10. 主握持部位 11. 调速开关 Page 2 Manual_Revised_V1.1

3 2. 工具规格 型号 CE CE 额定输入功率 ( 瓦 ) 额定转速 ( 转 / 分钟 ) 磨片直径 ( 毫米 ) 磨削厚度 ( 毫米 ) 螺纹直径 M10 M14 重量 ( 千克 ) 保护等级绝缘等级 E E 注 : 1. 为求改进, 本说明书所载规格可能不预先通告而给予更改 2. 本说明书提供的参数是以 220V 为依据, 若有低于或高于此电压的地区, 数据有可能不同 电动工具通用安全警告 警告! 阅读说明 按照以下例举的说明而使用或操作将导致触电 着火和 / 或严重伤害 在所有以 下列举的警告中术语 电动工具 指市电驱动 ( 有 线 ) 电动工具或电池驱动 ( 无线 ) 电动工具 保存这些说明 1. 工作场地 1) 保持工作场地清洁和明亮 混乱和黑暗的场 地会引发事故 2) 不要在易爆环境, 如有易燃液体 气体或粉 尘的环境下操作电动工具 电动工具产生的 火花会点燃粉尘或气体 3) 让儿童和旁观者离开后操纵电动工具 分心 会使你放松控制 2. 电气安全 1) 电动工具插头必须与插座相配 绝不能以任 何方式改装插头 需接地的电动工具不能使 用任何转换插头 未经改装的插头和相配的 插座将减少触电危险 2) 避免人体接触接地表面, 如管道 散热片和 冰箱 如果你身体接地会增加触电危险 3) 不得将电动工具暴露在雨中或潮湿环境中 水进入电动工具将增加触电危险 4) 不得滥用电线 绝不能用电线搬运 拉动电动工具或拔出其插头 让电动工具远离热 油 锐边或运动部件 受损或缠绕的电线会 增加触电危险 5) 当在户外使用电动工具时, 使用适合户外使用的外接电线 适合户外使用的电线将减少 触电危险 3. 人身安全 1) 保持警觉, 当操作电动工具时关注所从事的操作并保持清醒 切勿在有疲倦, 药物 酒 精或治疗反应下操作电动工具 在操作电动 工具期间精力分散会导致严重人身伤害 2) 使用安全装置 始终配戴护目镜 安全装置, 诸如适当条件下的防尘面具 防滑安全鞋 安 全帽 听力防护等装置能减少人身伤害 3) 避免突然起动 确保开关在插入插头时处于关断位置 手指放在已接通电源的开关上或 开关处于接通时插入插头可能会导致危险 4) 在电动工具接通之前, 拿掉所有调节钥匙或扳手 遗留在电动工具旋转零件上的扳手或 钥匙会导致人身伤害 5) 手不要伸得太长 时刻注意脚下和身体平衡 这样在意外情况下能很好地控制电动工具 6) 着装适当 不要穿宽松衣服或佩带饰品 让头发 衣服和袖子远离运动部件 宽松衣 服 佩饰或长发可能会卷入运动部件 7) 如果提供了与排屑装置 集尘设备连接用的装置, 则确保它们连接完好且使用得当 使 用这些装置可减少碎屑引起的危险 4. 电动工具使用和注意事项 1) 不要滥用电动工具, 根据用途使用适当的电动工具 选用适当的设计额定值的电动工具 会使你工作更有效 更安全 2) 如果开关不能接通或关断工具电源, 则不能使用该电动工具 不能用开关来控制的电动 工具是危险的且必须进行修理 3) 在进行任何调节 更换附件或贮存电动工具之前, 必须从电源上拔掉插头和 / 或将电池 Manual_Revised_V1.1 Page 3

4 盒脱开电源 这种防护性措施将减少电动工 具突然起动的危险 4) 将闲置电动工具贮存在儿童所及范围之外, 并且不要让不熟悉电动工具或对这些说明不 了解的人操作电动工具 电动工具在未经训 练的用户手中是危险的 5) 保养电动工具 检查运动件的安装偏差或卡住 零件破损情况和影响电动工具运行的其他 条件 如有损坏, 电动工具必须在使用前修理 好 许多事故由维护不良的电动工具引发 6) 保持切削刀具锋利和清洁 保养良好的有锋 利切削刃的刀具不易卡住而且容易控制 7) 按照使用说明书以及打算使用的电动工具的特殊类型要求的方式, 考虑作业条件和进行 的作业来使用电动工具 附件和工具的刀头 等 将电动工具用作那些与要求不符的操作 可能会导致危险情况 5. 维修 1) 将你的电动工具送交专业维修人员, 必须使 用同样的备件进行更换 这样将确保所维修 的电动工具的安全性 2) 当维修时, 仅使用有标示的零部件 3) 按照本说明书中维修部分操作 使用未经授 权的零件或未按该说明书中的指示操作可能 引发触电的危险 角磨工具的通用安全警告 通用安全警告 1. 该电动工具是用于实现砂轮机功能的 阅读随该电动工具提供的所有安全警告, 说明, 图解和规定 不了解以下所列所有说明将导致 电击 着火或严重伤害 2. 不推荐用该电动工具进行诸如砂光 刷光 抛光或切断等操作 电动工具不按指定的功能去操 作, 可能会发生危险和引起人身伤害 3. 不使用非工具制造商推荐和专门设计的附件 否则该附件可能被装到你的电动工具 上, 而它不能保证安全操作 4. 附件的额定速度必须至少等于电动工具上标出的最大速度 附件以比其额定速度大的速 度运转会发生爆裂和飞溅 5. 附件的外径和厚度必须在电动工具额定能力 范围之内 不正确的附件尺寸不能得到充分 防护或控制 6. 砂轮 法兰盘 靠背垫或任何其他附件的轴孔尺寸必须适合于安装到电动工具的主轴 上 带轴孔的 与电动工具安装件不配的附 件将会失稳, 过度振动并会引起失控 7. 不要使用损坏的附件 在每次使用前要检查 附件, 例如砂轮是否有碎片和裂缝, 靠背垫 是否有的裂缝, 撕裂或过度磨损 如果电动 工具或附件跌落了, 检查是否有损坏或安装 没有损坏的附件 检查和安装附件后, 让自 己和旁观者的位置远离旋转附件的平面, 并 以电动工具最大空载速度运行 1min 损坏的 附件通常在该试验时会碎裂 8. 戴上防护用品 根据适用情况, 使用面罩 安全护目镜或安全眼镜 适用时, 戴上防尘 面具 听力保护器 手套和能挡小磨料或工 件碎片的工程围裙 眼防护罩必须挡住各种 操作产生的飞屑 防尘面具或口罩必须能过 滤操作产生的颗粒 长期暴露在高强度噪声 中会引起失聪 9. 让旁观者与工作区域保持一安全距离 任何进入工作区域的人必须戴上防护用品 工件 或破损附件的碎片可能会飞出并引起紧靠着 操作区域的旁观者的伤害 切割附件触及带 电导线会使电动工具外露的金属零件带电, 并使操作者触电 10. 当在磨削附件有可能切割到暗线或自身电线的场所进行操作时, 只能通过绝缘握持面来 握住电动工具 切割机附件碰到一根带电导 线可能会使电动工具的外露金属零件带电并 使操作者发生电击危险 11. 使软线远离旋转的附件 如果控制不当, 软 线可能被切断或缠绕, 并使得你的手或手臂 可能被卷入旋转附件中 12. 直到附件完全停止运动才放下电动工具 旋 转的附件可能会抓住表面并拉动电动工具而 让你失去对工具的控制 13. 当携带电动工具时不要开动它 意外地触及 旋转附件可能会缠绕你的衣服而使附件伤害 身体 14. 经常清理电动工具的通风口 电动机风扇会 将灰尘吸进机壳, 过多的金属粉末沉积会导 致电气危险 Page 4 Manual_Revised_V1.1

5 15. 不要在易燃材料附近操作电动工具 火星可 能会点燃这些材料 16. 不要使用需用冷却液的附件 用水或其他冷 却液可能会导致电腐蚀或电击 附加安全说明 反弹和相关警告 : 反弹是因卡住或缠绕住的旋转砂轮 靠背垫 钢丝 刷或其他附件而产生的突然反作用力 卡住或缠绕 会引起旋转附件的迅速堵转, 随之使失控的电动工 具在卡住点产生与附件旋转方向相反的运动 例如, 如果砂轮被工件缠绕或卡住, 伸入卡住点 的砂轮边缘可能会进入材料表面而引起砂轮爬出 或反弹 砂轮可能飞向或飞离操作者, 这取决于 砂轮在卡住点的运动方向 在此条件下砂轮也可 能碎裂 反弹是电动工具误用和 / 或不正确操作工序或条 件的结果, 可以通过采取以下给出的适当预防措 施得以避免 1. 保持紧握电动工具, 使你的身体和手臂处于正确状态以抵抗反弹力 如有辅助手柄, 则 要一直使用, 以便最大限度控制住起动时的 反弹力或反力矩 如采取合适的预防措施, 操作者就可以控制反力矩或反弹力 2. 绝不能将手靠近旋转附件 附件可能会反弹 碰到手 3. 不要站在发生反弹时电动工具可能移动到的地方 反弹将在缠绕点驱使工具逆砂轮运动 方向运动 4. 当在尖角 锐边等处作业时要特别小心 避免附件的弹跳和缠绕 尖角 锐边和弹跳具 有缠绕旋转附件的趋势并引起反弹的失控 5. 不要附装上锯链 木雕刀片或带齿锯片 这 些锯片会产生频繁的反弹和失控 附加磨削和砂磨的专用安全警告 1. 只使用所推荐的砂轮型号和为选用砂轮专门设计的护罩 不是为电动工具设计的砂轮不 能充分得到防护, 是不安全的 2. 护罩必须牢固地装在电动工具上, 且放置得最具安全性, 只有最小的砂轮部分暴露在操 作人面前 护罩帮助保护操作者免于受到爆 裂砂轮碎片和偶然触及砂轮的危险 3. 砂轮只用于推荐的用途 4. 始终为所选砂轮选用未损坏的 有恰当规格和形状的砂轮法兰盘 合适的砂轮法兰盘支 承砂轮可以减小砂轮破裂的可能性 5. 不要使用从大规格电动工具上用剩的磨损砂轮 用于大规格电动工具上的砂轮不适于较 小规格工具的高速工况并可能会爆裂 角磨使用注意事项 1. 该角磨仅用于磨削 2. 在操作时, 避免磨片撞击或其它强力性动 作 一旦发生, 必须立刻停机检查 3. 若工具起动后, 出现明显颤动或其它异常, 请立即停机, 排除故障后方可继续操作 4. 打磨金属时会产生火花 小心勿让火花及研 磨屑喷到身上 5. 研磨含硅酸石材时, 产生的灰尘有害健康 不可加工含石棉材料的工件 6. 在粉尘过多的环境下, 应缩短电动工具的清 洁周期 7. 本机只可用于干式加工 代表符号 以下符号可以帮助您正确地使用本电动工具 请 牢记各符号和它们的代表意思 正确了解各符号 的代表意思, 可以帮助您更有把握更安全地操作 本电动工具 符号 含义 危险范围! 手掌, 手臂和手指头必 须尽可能远离这个范围 请佩戴护目镜 佩戴耳罩 工作噪音会损坏听力 请佩戴防尘面具 Manual_Revised_V1.1 Page 5

6 佩戴工作手套 齿轮箱盖 非切割片护罩 警告 : 器具工作时产生的粉尘可能含 有致癌或对人体有害的化学物质 例如 : 油漆中含的铅 砷和铬与木材起反应后也会产生有毒物质 为了减少这些有毒的化学物质对人体的伤 害, 要尽量保证在通风的环境下工作, 并且工作 时配戴合格的安全保护装置 配备 扳手 在某些国家或某些特殊的机型, 其所提供的配 备, 可能与以上所给的资料稍有出入 安装手柄 注意 : 操作前不安装手柄是不允许的 为了满足消费者的不同需求, 角磨的手柄有两处 不同的位置可以安装 安装手柄 : 将手柄旋转进电机头部位的孔内 操作前, 请检查手柄已经牢固的安装到位, 但不 要过度的拧紧 螺钉 操作说明 警告 : 为了避免意外开动电动工具 安装锯片时, 或进行电动工具的维护修理工作时, 机器的插头都不可以插在插座中 检查供电电压须与铭牌数据相符! 安装护罩 警告 : 当使用角磨来打磨时, 务必确保护罩是正确安装在机器上 注意 : 有受伤风险! 请带上防护手套 1) 拔下插头 2) 将护罩箍上的突起部分与齿轮箱盖上的沟槽吻 合 3) 顺时针旋转护罩 4) 逆时针方向旋转为拆卸护罩 安装磨片 不得使用安全线速度低于 80m/s 的砂轮, 严禁使 用损坏 不平衡的砂轮! 1) 按下并按住角磨轴锁 2) 使用扳手来松开角磨轴上的紧固螺母 3) 将磨片正确的放置好 4 ) 安装磨片时 : 凸起的一面朝内 5) 按住角磨轴锁 6) 使用扳手拧紧紧固螺母 7) 在使用前, 请试运行一下角磨, 检查各个部件是 不是安装到位 注意 : 在使用前, 请先运行角磨大于 30 秒左右, 检查角磨各个部件是不是安装到位, 有无异 常振动 Page 6 Manual_Revised_V1.1

7 注意 : 工具的损坏会导致人身伤害 操作时, 请选用恰当的工具 实际应用 注意 : 如果在持续操作时需要过载或是过热的情况时, 机器会自动降速直到工具逐渐冷却下 来 3. 打磨 将工具以 位置操作时会达到最佳的效 果 使用时, 请使用恰当的力度, 在工件的表面来回 移动角磨 因此, 加工件不会变的特别热, 也不 会导致变色 打磨金属时会产生火花, 火花散射范围内, 严禁存放任何可燃物料, 以免火灾! 注意 : 电源的电压! 电源的电压必须和电动工具铭牌上标示的电压一致 操作之前先检查磨片 不仅要正确地安装好磨 片, 而且磨片必须能够无阻地旋转 必须进行至 少 30 秒的无载试机 不可以使用已经损坏 变形 或会震动的磨片 损坏的磨片可能会破裂并且造 成伤害 加工含铅的颜料以及矿物和金属所产生的废尘有 害健康 工作场所要保持空气流通 最好佩戴 P2 滤网等级的口罩 1. 开动和关闭 检查工具的开关操作是否自如, 确保插电前开关 处于关停状态! 1) 将开关向前推并按住 2) 松开开关, 来关闭机器 3) 连续操作 : 将开关向前推, 并将开关的前端往 下按 4 ) 关闭机器时, 按下开关尾部 注意 : 如果突遇断电, 通电后, 开关将不会重新启动 2. 调速 拨动调速盘来选择合适的操作速度 旋钮设定转速 ( 转 / 分钟 ) 工具维护保养 注意 : 进行维修检查之前, 必须把插头拔离电源插座!! 1. 避免工具受到震荡 撞击或油脂影响 2. 检查安装螺钉 经常检查安装螺钉是否紧固 稳妥 螺钉松开极易引起严重事故 3. 定期检查线缆 如发现损伤应立即委托 授权的维修中心处理 4. 保持通风槽清洁顺畅 经常清除尘埃 油 污, 严防杂物入内 5. 更换碳刷 经授权的维修中心检查 和更换碳刷, 以保证工具长期安全使用 6. 必须由授权的维修中心进行维修 只能使用的配件 零件 7. 清洁 避免使用造成塑料龟裂损坏的溶剂擦 拭塑料零件 建议使用稍微沾湿了肥皂水的 柔布擦拭外塑料机壳 Manual_Revised_V1.1 Page 7

8 请勿让马达淋到水, 禁止将整个机身投入水中, 以免引起马达故障及触电事故! 环境保护 1. 的包装可以百分之百进行回收再生 处理 2. 报废的电动工具和附件中含有大量有价值的 原材料及合成材料, 同样可以进行再生回 收 3. 磨削时所产生的粉尘中会包含有害物质, 因而不应作为普通垃圾倾倒, 而应交给特殊垃圾回收站处理 服务 1. 工具需要保修时, 请自行送至当地特约维修中心, 并提供有效保修卡及购机发票原件, 遗失保修卡恕不补发 2. 由于正常磨耗 过载或不当使用而导致的损坏, 不在保修范围内 附 : 一般故障及排除方法 故障 原因 排除方法 1. 电源断了 1. 修复电源 1. 接电后电机不运转 2. 接头松落 2. 检查所有接头 3. 开关接触不良或不动作 3. 修理或更换开关 4. 电刷与换向器表面不接触 4. 更换碳刷 1. 开关触点烧坏 1. 修理或更换开关 2. 接电后有异声且不旋转或转得很慢 2. 机械部分卡住 2. 检查机械部分 3. 换向器上产生环火或较大火花 1. 电枢短路 1. 修复电枢 2. 电刷和换向器接触不良 2. 更换碳刷 4. 旋转慢且有异声 1. 磨片损坏 1. 更换磨片 2. 磨片碰到钢筋 2. 重新选择作业点 Page 8 Manual_Revised_V1.1

9 DESCRIPTION OF THE TOOL 1. MAIN PARTS The power tool is intended for dry grinding metal and stone. Read, understand and follow all safety rules and instructions before using this tool Spindle lock button 2. Shift direction 3. Spindle 4. Non-cutting guard 5. Inner flange 6. Wheel 7. Outer flange 8. Spanner 9. switch 10. Primary hold part 11. Dial for preselecting the speed Manual_Revised_V1.1 Page 9

10 2. TOOL SPECIFICATIONS Model CE CE Rated power input (W) Rated speed (/min) Max. grinding tool Ø (m) Grinding tool thickness (m) Spindle thread (m) M10 M14 Weight (kg) Protection class Insulation grade E E NOTE 1: Due to s continuing program of development, the specifications herein are subject of change without prior notice. NOTE 2: The values given are valid for nominal voltages [U] of 220 V. For lower or higher voltages and models for specific countries, these values can vary. GENERAL SAFETY RULES WARNING: Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. The term power tool in all of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless) power tool. Save these instructions. 1. WORK AREA SAFETY 1) Keep work area clean and well lit. Cluttered and dark areas invite accidents. 2) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. 3) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2. ELECTRICAL SAFETY 1) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. 2) Avoid body contact with earthed or grounded surfaces such as pipes, radiators and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. Page 10 3) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 4) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. 5) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. 3. PERSONAL SAFETY 1) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. 2) Use safety equipment. Always wear eye protection. Safety equipment such as a dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. 3) Avoid accidental starting. Make sure that the switch is in the OFF position before plugging the tool into an electrical outlet. Carrying power tools with your finger on the switch or plugging in power tools that have the power switch ON invites accidents. 4) Remove any adjusting key or wrench before turning the tool on. A wrench or a key that is left attached to a rotating part of Manual_Revised_V1.1

11 the power tool may result in personal injury. 5) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. 6) Dress properly. Do not wear loose clothing or jewellery. Keep your clothing, gloves and hair away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. 7) If devices are provided for the connection of dust extraction and collection facilities, ensure that these are connected and properly used. Use of these devices can reduce dust-related hazards. 4. POWER TOOL USE AND CARE 1) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 2) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 3) Disconnect the plug from the power source or come away the battery box from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. 4) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. 5) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. 6) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. 7) Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different form intended could result in a hazardous situation. 5. SERVICE 1) Have your power tool serviced by a qualified repair person. 2) When servicing a power tool, use only identical replacement parts. 3) Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance instructions may create a risk of shock or injury. ALL OF SAFETY RULES 1. This power tool is intended to function as a grinder tool. Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. 2. Do not recommend use this power tool operations as sander, wire brush and so on. Used this power tool do besides appointed function will cause hazards and personal injuries. 3. Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation. 4. The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can fly apart. 5. The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled. Manual_Revised_V1.1 Page 11

12 6. The arbor size of wheels, flanges, backing pads or any other accessory must properly fit the spindle of the power tool. Accessories with arbor holes that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control. 7. Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for chips and cracks, backing pads for cracks, tear or excessive wear. If the power wool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time. 8. Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and shop apron capable of stopping small abrasive or work piece fragments. The eye protection must be capable of stopping flying debris generated by various operations. The dust mask or respirator must be capable of filtrating particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss. 9. Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective equipment. Fragments of the work piece or of a broken accessory may fly away and cause injury beyond the immediate area of operation. Contact with live wire will also make exposed metal parts of the power tool live and shock the operator. 10. Hold the power tool only by the insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own power cord. Contact with a live wire will also make exposed metal parts of the power tool live and shock the operator. 11. Position the cord clear of the spinning accessory. If you lose control, the cord may Page 12 be cut or snagged and your hand or arm may be pulled into the spinning accessory. 12. Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control. 13. Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body. 14. Regularly clean the air vents of the power tool. The fan of the motor will draw dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards. 15. Do not operate the power tool near flammable materials. Sparks could ignite these materials. 16. Do not use accessories that require coolants. Using water or other coolants may result in electric cauterization or electric shock. ADDITIONAL SAFETY WARNING Kickback and related warnings: Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory s rotation at the point of the binding. For example, if an abrasive wheel is snagged or pinched by the work piece, the edge of the wheel that is entering into the pinch point can dig into the surface of the material causing the wheel to climb out or kick out. The wheel may either jump toward or away from the operator, depending on the direction of the wheel s movement at the point of pinching. Abrasive wheels may also break under these conditions. Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below. 1. Maintain a firm grip with your hands on the power tool and position your body and arm to allow you to resist kickback forces. Always use the auxiliary handle, for maximum control over kick- back or torque reaction during start-up. The operator can Manual_Revised_V1.1

13 control torque reactions or kick back forces, if proper precautions are taken. 2. Never place your hand near the rotating accessory. The accessory may kickback over your hand. 3. Do not position your body in the area where the power tool will move if kickback occurs. Kickback will propel the tool in the direction opposite to the wheel s movement at the point of snagging. 4. Use special care when working sharp edges, sharp sides etc. Avoid bouncing and snagging the accessory. Sharp edges, sharp sides or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback. 5. Do not attach a saw chain, woodcarving blade or toothed saw blade. Such blades create frequent kickback and loss of control. ADDITIONAL GRINDING SAFETY WARNING 1. Use only wheel types that are recommend for you power tool and the specific guard designed for the selected wheel. Wheel for which the power tool was not designed cannot be adequately guarded and are unsafe. 2. The guard must be firmly attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator. The guard helps to protect the operator from broken wheel fragments and accidental contact with the wheel. 3. Wheels must be used only for recommended applications. 4. Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. 5. Do not use worn down wheels from larger power tools. A wheel intended for a larger power tool is not suitable for the higher speed of a smaller tool and may burst. USE CARE OF ANGLE GRINDER 1. The grinder is intended for grinding. 2. Avoid the wheel impact or force actions, if this condition occurs, stop the machine immediately and check the machine. 3. If there is considerable vibration or other defects are detected in operation, stop the machine immediately and check the machine to determine the cause. 4. When grinding metal, flying sparks are produced. Take care that sparks resulting from use do not hit persons. 5. Some dust created by power grinding contains chemicals known to birth defects. Do not work with materials containing asbestos. 6. Shorten the clean periods when working in dusty conditions. 7. The machine should only be used only for dry working. SYMBOL Danger area! Keep hands, fingers or arms away from this area. Wear safety goggles. Wear ear protectors. Exposure to noise can cause hearing loss. Wear a dust respirator. Wear protective gloves. WARNING: Some dust created by power Cutting contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: Lead from lead-based paints Arsenics and chromium from chemically reacted lumber. Manual_Revised_V1.1 Page 13

14 Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment. STANDERD ACCESSORIES positions around the casing to meet the operator s different needs. To assemble the handle, simply screw it into one of the attachment points. Check that the handle has been securely fastened, but don t screw it in too tightly. Spanner Be sure to check the accessories as it is subject to change by areas and models. OPERATION POWER SUPPLY The power tool supply must match the nameplate date. Attach the Guard WARNING: When using the angle grinder for roughing, never work without the guard. CAUTION! Risk of injury! Wear protective gloves. 1) Pull out the mains plug. 2) Lugs on the guard hood must be located in the flange recesses. 3) Turn guard hood clockwise. Rotation is possible in one direction only! 4) Remove in reverse order. Gear Case Cover Non-cutting Guard Attach the grinding wheel WARNING: Only use grinding wheels with maximum safe operating speed rated at or above 80m/s. Never use damaged or imbalance grinding wheels. 1) Press and hold down the spindle lock. 2) Using the face spanner, loosen the clamping nut on the spindle in an anti-clockwise direction and remove. 3) Insert the grinding wheel in the correct position. 4) Screw the clamping nut with flange face up, onto the spindle. 5) Press and hold down the spindle lock. 6) Tighten the clamping nut with the face spanner. 7) Carry out a test run to check that the tool is clamped in the centre. NOTE: Switch on the angle grinder with the switch (without engaging it) and run the angle grinder for approx. 30seconds. Check for imbalances and vibrations. Screw Attach the Handle NOTE: It is not permitted to operate the electric power tool without the handle. The handle can be assembled in two different Page 14 Manual_Revised_V1.1

15 Rough-grinding APPLICATION NOTE: Observe correct mains voltage! Switching On and Off 1) Push the switch rocker forwards and hold in position. 2) To switch off the power tool, release the switch rocker. 3) For continuous operation, push the switch rocker forwards and engage by pressing the front end. 4) To switch off the power tool, release the switch rocker by pressing the rear end. NOTE: Following a power failure, the switched on power tool does not restart. Preselecting the Speed To set the operating speed, move the dial to the required value. Dial Setting r/min CAUTION! Risk of injury due to destruction of the tool. Use the appropriate tool for the job. NOTE: If an overload or overheating occurs during continues operation, the power tool automatically reduces the speed until the power tool has cooled down adequately. WARNING: Never use cutting-off wheels for rough-grinding. Angle of wheel for best performance. Applying moderate pressure, move the angle grinder backwards and forwards. As a result, the workpiece will not become too hot and there will be no discoloration; nor will there be any grooves. WARNING: Sparks generated when grinding metal. Take care that no combustible material presented in the area of flying sparks. TOOL MAINTENANCE WARNING: Before any work on the machine itself, unplug the saw from the power source. 1. Inspect bolts periodically. If the bolts loosen, tighten them immediately, or will result in serious accident. 2. Inspect tool cords periodically. The cord is special prepared, if damaged, have repaired at your nearest Authorized s Service Center. This tool was used with the power cord as a particular structure; don t replace the power cord without authorization, such as replacement, please go to the Authorized s Service Center. 3. Keep the vents clean. Clean all parts of the tool, clean dust periodically. To prevent debris from entry. Manual_Revised_V1.1 Page 15

16 4. Replace the carbon brush when the carbon brush is worn out in certain length and motor stops running. All maintenance should be carried Out by Authorized Service Center. 5. All service MUST only be performed by Authorized Service Center. ALWAYS use only that are recommended for this tool. accessories 6. Cleaning. Avoid the use of plastic cracks caused by damage to the solvent. Use clean cloths and mild soap to remove dirt, dust, etc. 7. Avoid the tool vibration or impact, and keep it from oil and grease. WARNING: Do not allow the water entering the motor and the tool full immersed in the ware, which will result in motor malfunction and electric shock. packaging should be sorted for environment-friendly recycling. 2. Power tools and accessories at the end of their service life still contain large amounts of valuable raw materials and plastics which can likewise be fed back into a recycling process. 3. Some dust created by working contains harmful chemicals must be collected by special garbage re- cycle site. SERVICE 1. In case of guarantee, repair or purchase of replacement parts, always contact the qualified service center. And supplied with the efficient service card and invoice. 2. It is without the scope of guarantee when the tool was normal wear, overload or improper use of damage. ENVIRONMENT PROTECTION 1. s tool, accessories and Trouble Shooting Problems Reasons Ways to Solve The Problems 1. Unconnected to power source 1. Connect to power source 2. Plugs not fully connect 2. Check all plugs 1. The motor stops running 3. Switch out of work 3. Replace or repair the switch 4. Brushs not touch the commutator 4. Replace the brushs with two new ones 2. Running slowly (Not running) with the noise 1. Switch out of work 1. Replace or repair the switch at the beginning of power turn-on 2. Mechanical trouble 2. Check mechanical parts 1. Armature short circuit 1. Repair the armature 3. Commutator sparkle 2. Poor connection between the brush and the commutator 2. Replace it with a new one 3. Commutator surface not smooth 3. Clean the commutator surface 4. Running slowly with 1. Bearing worn out 1. Replace it with a new one the noise in process 2. Grinding wheel touched ofworking reinforcing steel bar 2. Chose another work place Page 16 Manual_Revised_V1.1

17

18

19

20 中国南京江宁经济技术开发区将军大道 159 号制造商 :( 外商独资 ) 南京德朔实业有限公司 No.159 Jiang-Jun Rd., Nanjing Jiangning Economic & Technical Development Zone. Nanjing , P.R.China Tel: Fax: