2213 .pdf

Size: px

Start display at page:

Download "2213 .pdf"

怡纷充
5 years ago
Views:

1 2213 GB Palm Sander

2 V 220 Hz 50 W 200 /min mm 1.6 mm 110x100 kg 1.3 E page 1 Manual_Revised_V1.0

3 4) 5) 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 1) 2) 3) 4) 5) 6) 7) 8) 1 2 Manual_Revised_V1.0 page 2 page 3 Manual_Revised_V1.0

4 Manual_Revised_V1.0 page 4 page 5 Manual_Revised_V1.0

5 DESCRIPTION OF THE TOOL OPERATING CONTROL The sander is designed for dry sanding on timber, plastic, and the surfaces of lacquer. Read, understand and follow all safety rules and instructions before using this tool. 1. MAIN PARTS 1.Switch 2.Paper clamp 3.Soft pad 4.Bottom support 1 5.Handle TOOL SPECIFICATIONS Model 2213 Rated voltage ( V ) 220 Rated frequency ( Hz ) 50 Rated input power ( W ) 200 Speed ( /min ) Orbit diameter ( mm ) 1.6 Sanding base ( mm ) 110x100 Weight ( kg ) 1.3 Protected grade Insulated grade E Note: Due to s without prior notice. Manual_Revised_V1.0 page 6 page 7 Manual_Revised_V1.0

6 GENERAL SAFETY RULES WARNING: Read all instructions. Failure to follow all instructions listed below may result in The term power tool in all of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless) power tool. SAVE THESE INSTRUCTIONS WORK AREA 1. Keep workplace clean and well lit. Cluttered and dark workplaces invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of create sparks which may ignite the dust or fumes. Personal safety 1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are or medication. A moment of inattention while operating power tools may result in serious 2. Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non- skid safety shoes, hard hat, or hearing protection used for appropriate 3. Avoid suddenly starting. Ensure the switch is in the off position before plugging in. When power tools that have the switch on invites accidents. shields. Everyday glasses may have impact resistant lenses, but they are not safety glasses. Following this rule will reduce the 12. Protect your lungs. Wear a face or dust mask if the operation is dusty. Following this rule will reduce the risk of serious personal 13. Protect your hearing. Wear hearing protection during extended periods of operation. Following this rule will reduce the Power tool use and care 1. Do not force the power tool. Use the correct power tool for your application. The correct the rate for which it was designed. a hazardous situation. 8. Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you lend this tool to someone else, also lend them these instructions. Service repair person. 2. When servicing a power tool, use only identical replacement parts. 3. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance instruc- ADDITIONAL SAFETY RULES FOR SANDER 2. Do not use the power tool if the switch 3. Keep children and bystanders away while does not turn it on and off. Any power tool 1. Place the cord in rear of the tool. operating a power tool. Distractions can cause you turning the power tool on. A wrench or a key that cannot be controlled with the switch is to lose control. left attached to a rotating part of the power 2. Clamp work piece securely with clamping dangerous and must be repaired. devices or a vise. Electrical safety 3. Disconnect the plug from the power source 5. Do not overreach. Keep proper footing and 3. Never drill any hole in the housing of the 1. Power tool plugs must match the outlet. Never balance at all times. This enables better tool, which will result in electric shock. modify the plug in any way. Do not use any accessories, or storing power tools. Such control of the power tool in unexpected 4. Keep your workplace clean. Blends of adapter plugs with earthed (grounded) power preventive safety measures reduce the risk situations. materials are particularly dangerous. Dust of starting the power tool accidentally. 6. Dress properly. Do not wear loose clothing from light alloys can burn of explode. reduce risk of electric shock. 4. Store idle power tools out of the reach of 5. Do not use the power tool with a damaged 2. Avoid body contact with earthed or grounded children and do not allow persons unfamiliar gloves away from moving parts. Loose cord. Do not touch the damaged cord and surfaces such as conduits, radiators, and with the power tool or these instructions pull the plug from the outlet when the cord refrigerators. There is an increased risk of electric to operate the power tool. Power tools are in moving parts. is damaged while working. Damaged cords shock if your body is earthed or grounded. dangerous in the hands of untrained users. 7. f devices are provided for the connection increase the risk of an electric shock. 3. Do not expose power tools to rain or wet 5. Maintain power tools. Check for misalignment or binding of moving parts, breakage of of dust extraction and collection facilities, 6. Wear ear protection in continuous working conditions. Water entering a power tool will ensure these are connected and properly time. increase the risk of electric shock. parts and any other condition that may affect used. Use of these devices can reduce dust the power tools operation. If damaged, have 7. Keep your hands far away from the rotating 4. Do not abuse the cord. Never use the cord for related hazards. the power tool repaired before use. Many components. carrying, pulling or unplugging the power tool. 8. Use clamps or another practical way to accidents are caused by poorly maintained Keep cord away from heat oil, sharp edges or support and secure the workpiece to a power tools. moving parts. Damaged or entangled cords and hold it securely still in operation. stable platform. Holding the work by hand increase the risk of electric shock. 6. Keep cutting tools sharp and clean. Properly or against your body leaves it unstable and 9. Do not work materials containing asbestos. maintained cutting tools with sharp cutting 5. When operating a power tool outdoors, use an may lead to loss of control. Asbestos is considered carcinogenic. edges are less likely to bind and are easier extension cord suitable for outdoor use. Use of a 9. Do not use on a ladder or unstable support. to control. 10. Never allow children to use the machine. cord suitable for outdoor use reduces the risk of Stable footing on a solid surface enables 7. Use the power tool, accessories and tool bits 11. Make sure if the sanding sheet or the base electric shock. better control of the power tool in unexpected etc., in accordance with these instructions plate is crackled or damaged. Crackled 6. If operating a power tool in a damp location is situations. and in the manner intended for the particular or damaged base plate would result in unavoidable, use a residual current device (RCD) 10. Keep handles dry, clean, and free from oil type of power tool, taking into account the protected supply. Use of an RCD reduces the risk and grease. Slippery hands cannot safely working conditions and the work to be performed. Use of the power tool for operations not suitable for wet sanding. 12. The tool hasn t waterproof feature, and it is of electric shock. control the power tool. different from those intended could result in 11. Always wear safety glasses with side Manual_Revised_V1.0 page 8 page 9 Manual_Revised_V1.0

7 13. Never clean any dust or dirt during APPLICATION operation. 14. The tool can be operated when the sanding OPERATION sheet is attached and clamp securely. Switch the sander on whilst it is resting on the WARNING: Some dust created by work piece. Take care to hold the whole surface power Cutting contains chemicals of the platen on the work piece. Move the known to cause cancer, birth sander over the surface of the work in a circular defects or other reproductive motion with an even, moderate pressure. harm. Some examples of these Extreme pressure will reduce the tool lift. chemicals are: Note: Do not block the wind intake of the lead from lead-based paints motor with hand. 3. SWITCHING ON AND OFF arsenics and chromium from chemically To switch the sander on by depressing the reacted lumber. trigger switch in the position 1, to turn off Your risk from these exposures varies, the sander, depress the trigger switch in the depending on how often you do this type position 0. of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment. STANDARD ACCESSORIES N/A Be sure to check the accessories as it is TOOL MAINTENANCE OPERATION 4. GRASP THE SANDER WARNING: Before any work on the 1. POWER SUPPLY The sander can be grasped in two methods to machine itself, unplug the power supply. satisfy different operators for more comfortable The power tool supply must match the Inspect bolts periodically. If the bolts loosen, nameplate date. tighten them immediately, or will result in 2. ATTACHING SANDING SHEETS serious accident. WARNING: Always disconnect the Inspect tool cords periodically. If damaged, machine from the power supply before have repaired at your nearest Authorized attaching or remove sanding sheets. Service Center. This tool was Locate the clamps on either side of the machine, used with the power cord as a particular loosen the clamp levers, position one end of the structure, don t replace the power cord sanding sheet under the clamp and secure the without authorization, such as replacement, 5. SELECTING THE SANDING SHEET clamping lever. The sanding sheet should be please go to the Authorized pulled taut and follow the contours of the sander Depending on the material to be worked and Service Center. base. Ensure alignment of dust extraction holes the required rate of material removal, different Keep the vents clean. Clean all parts of on the on the sander soleplate with the holes in sanding sheets are available: the tool, clean dust periodically. To prevent the sanding sheet. Position the other end of the sanding sheet under the clamp and secure the Grit Type debris from entry. clamp lever. 60 or less Very Coarse Replace the carbon brush when the carbon Coarse Note: When the sanding sheet is attached, brush is worn out in certain length and motor Medium check and make sure the sanding paper is stops running. All maintenance should be Fine clamped properly and securely, do follow this carried Out by Authorized Service Center, will cause uneven surface of work piece. 240 or more Very Fine and only use identical repair parts. All service MUST only be performed by Authorized Service Center. ALWAYS use only accessories that are recommended for this tool. Cleaning. Avoid the use of plastic cracks caused by damage to the solvent. Use clean cloths and mild soap to remove dirt, dust, etc. Avoid the tool vibration or impact, and keep it from oil and grease. WARNING: Do not allow the water entering the motor and the tool full immersed in the ware, which will result in motor malfunction and electric shock. 1. REPLACEMENT OF CARBON BRUSH The sander is built in replaceable brush, please use the brush from authorized service center. 1) Unplug the sander. 2) Remove the screws in the motor cap of the sander then remove the locking screws of the brush by Philip screwdriver. 3) Depress the clasp to release the brush using a slotted screwdriver. 4) Remove brush assemblies, and replace a new one. 5) Reassemble by reversing the steps listed above. 6) Tighten all brush caps securely. Do not over tighten. The tool should be allowed to RUN IN for several minutes before use, to seat the new brushes properly. 2. REPLACEMENT OF PAPER CLAMP 1) Unplug the sander. 2) Set the sander upside down on the table, make the sub base face the operator. 3) Remove the screws on the base using Philip screwdriver, the paper clamp will release Manual_Revised_V1.0 page 10 page 11 Manual_Revised_V1.0

8 automatically. Problem Shooting 4) Replace the paper clamp. Problems Reasons Ways to Solve The Problems 5) Reassemble by reversing the steps listed 1. Unconnected to power source 1. Connect to power source above. 6) Tighten all screws in the base securely. Do 2. Plugs not fully connect 2. Check all plugs not over tighten. 1. The motor stops running 3. Switch out of work 3. Replace or repair the switch 4.Brushes not touch the commutator 4. Replace the brushes with two new ones 2. Running slowly (Not 1. Switch out of work 1. Replace or repair the switch running) with the noise 2. Mechanical trouble 2. Check mechanical parts at the beginning of power turn-on 1. Armature short circuit 1. Repair the armature ENVIRONMENT PROTECTION 2. Poor connection between the 2. Replace it with a new one brush and the commutator 3. REPLACEMENT OF VIBRATION 3. Commutator sparkle 3. Commutator surface not smooth 3. Clean the commutator surface BRACKET 4. stator wires are connected 4. rewire the stator according the 1) Unplug the sander. reversely instructions 2) Set the sander upside down on the table, 1. Tool, accessories and packaging should be 4. Running slowly 1. Bearing worn out 1. Replace it with a new one make the sub base face the operator. sorted for environment-friendly recycling. 3) Remove the screws on the base using Philip 2. Power tools and accessories at the end of screwdriver. their service life still contain large amounts 4) Remove the bracket locking screws by Philip of valuable raw materials and plastics which screwdriver. can likewise be fed back into a recycling 5) Replace the vibration bracket. process. 6) Reassemble by reversing the steps listed above. 3. Some dust created by working contains 7) Tighten all the screws in the base securely. harmful chemicals must be collected by Do not over tighten. special garbage re- cycle site. SERVICE 1. In case of guarantee, repair or purchase of replacement parts, always contact the 2. It is without the scope of guarantee when the tool was normal wear, overload or improper use of damage. 4. REPLACEMENT OF STATOR Connect the stator according the hookup on the top of the motor housing. Be careful the black and blue lines should never be connected reversely, otherwise, the problems rotation speed, or brokenly rotation. Manual_Revised_V1.0 page 12 page 13 Manual_Revised_V1.0

9 Tapping Screw Housing Cover( ) Middle Housing() Stator( ) Tapping Screw Rotor Set() Ball Bearing( ) Plain Washer( ) Insulated Pad Rotor( ) Dust Washer() Mounting Plate A Ball Bearing( ) Plain Washer( ) Bearing Support() Screw Fan( ) Ball Bearing ( ) Plain Washer( ) Screw Pad Support Mounting Plate BB Paper Clamp Assy() Paper Clamp() Plate Lever Base Assy Base Plate Soft Pad Sand Paper Switch Cover() Fixing Board Rocker Switch() Receptacle Sleeve() Tapping Screw Brush Holder Carbon Brush Tapping Screw PCB Assembly Tapping Screw Cord Anchorage Cord Guard Power Cord & Plug 1 Manual_Revised_V1.0 page 14 page 15 Manual_Revised_V1.0

11 Economic & Technical Development Zone. Tel: Fax:

000Book_SV12SH.indb

000Book_SV12SH.indb Orbital Sander SV 12SH Handling instructions Read through carefully and understand these instructions before use. 1 2 1 1 3 4 A B 3 4 2 5 5 English 1 Sanding paper 2 Dust gate 3 Dust bag 4 Dust outlet