1 of 6 Balun Design In the design of mixers, push-pull amplifiers, baluns are used to link a symmetrical (balanced) circuit to a asymmetrical (unbalanced) circuit. Baluns are designed to have a precise 180-degree phase shift, with minimum loss and equal balanced impedances. In power amplifiers loss of symmetry will degrade efficiency and the symmetrical port must be well isolated from ground to eliminate parasitic oscillations. The basic construction/design of a balun consists of two 90-degree phasing lines that provide the required 180-degree split, and this involves the use of λ/4 and λ/2. A wire-wound transformer provides an excellent balun. Miniature wirewound transformers are commercially available covering frequencies from low khz to beyond 2GHz. They are often realised with a centre-tapped secondary winding, if grounded this provides a short circuit to even-mode (common-mode) signals whilst having no effect on the differential (odd-mode) signal. Wire-wound transformers are more expensive than the printed or lumped element baluns described below, which find greater adoption in practical mixer designs. It should be noted that most of these lumped element and printed baluns do not provide the centre-tapped ground to even mode signals and this fact must be accounted for in the mixer design. (1) L-C Balun This design is essentially a bridge and is known as a lattice-type balun. It consists of two capacitors and two inductors, which produce the ± 90 degree phase shifts. The diagram below (Figure 1) shows the circuit diagram of the Balun. L R I C Balanced Input R L C L Figure 1 Schematic diagram of a L-C lumped balun. At operating frequency ω = 2πf and Zc = R.R I L Zc L = ω ; C 1 = ω.zc
2 of 6 When designing this circuit make sure that the operating frequency is well below the selfresonant frequencies of the components and take account of pad capacitances. One of the main applications of this circuit is on the output of a push-pull amplifier, which provides a balanced signal and we want to convert to a single un-balanced output. Normally a wound toroid style of balun is used as shown in Figure 2. Vcc Balun O/P Figure 2 Use of a wire-wound balun on the output of a push-pull amplifier stage to provide a balanced to unbalanced conversion.
3 of 6 However, it may be convenient especially at chip level to realise the wound transformer type balun, with the previously described lumped balun as shown in Figure 3. RF Decoupling L1 Vcc C1 Bias Choke Balanced Input L2 O/P C2 Figure 3 The balanced to unbalanced transformation can achieved by using lumped components instead of a wound transformer. (2) Transmission Line This balun can be realised from a λ/4 length of line or coax as shown in Figure 4: (a) 1:1 Coaxial Balun Input Balanced Figure 4 Coaxial balun realised from a quarter length of coaxial cable, and gives a 1:1 impedance transformation.
4 of 6 If we require an impedance transformation of 1:4 then we can utilise the coaxial balun as shown in Figure 5. (b) 1:4 Coaxial Balun Balanced Input R (ohms) 4 * R (ohms) λ/2 line Z0 = 2 * R Figure 5 Coaxial balun realised from a quarter length of coaxial cable, and gives a 1:4 impedance transformation (3) Microstrip There are a wide-range of printed/micro-strip balun topologies they have the advantage of being inexpensive, realised as they are on the Printed Circuit Board (PCB) or Microwave Integrated Circuit (MIC) substrate. On the downside they can be quite large, particularly at lower RF frequencies. The rat-race coupler is commonly used at microwave frequencies for bandwidths of up to around 10-20%. Un-balanced Input Balanced Figure 6 Simple coupled line balun The simplest printed balun is the coupled line balun, also called a parallel-line balun shown in Figure 6. The structure is a quarter of a wavelength long at the centre frequency. It is capable of bandwidths of over an octave, provided the coupling between the lines is high enough. In practice this is not normally the case for the simple edge coupled balun shown in Figure 7.
5 of 6 Un-balanced Input Balanced Figure 7 Coupled line balun using multiple coupled lines A more practical approach is to use multiple coupled lines as shown in Figure 7 or, where multi-layer substrate processing is available, to adopt a broad-side coupler topology as in Figure 8. This broadside-coupled implementation is often referred to as a parallel plate balun. Balun on top surface Un-Balanced Input Balanced Ground plane on bottom Figure 8 Coupled line balun, using broadside coupler structure An improvement on the parallel-line balun is a printed version of the Marchand Balun. This is derived from the co-axial balun, described by Nathan Marchand in 1944. The printed version of the Marchand balun is shown in its simplest form in Figure 9. This is more tolerant to low even mode impedance (low coupling ratio) than the parallel line balun and has a wider bandwidth. Un-balanced Input Figure 9 Printed Marchand Balun Balanced
6 of 6 As with the parallel line balun, improved performance is obtained if multiple planar section are used or if a broadside coupling topology is adopted. One draw back to using these printed baluns at lower RF frequencies is their size. As with the parallel line and Marchand baluns, the use of broadside, rather than edge, coupling will yield tighter coupling and improved performance. Finally we can realise the LC balun type balun using microstrip techniques. Here we are using the microstrip equivalents of capacitors and inductors as shown in Figure 10. Fan load Shunt Decoupling Capacitor λ/4 Bias Choke L1 C1 Balanced Input C1 L2 DC Block Figure 10 LC balun type balun using micro-strip techniques to realise capacitors and inductors. Shunt Capacitors to ground, are realised a low impedance (ie wide track) open circuit stubs, while inductors are realised as high impedance lines (very narrow tracks). The fan load also acts as a shunt capacitor to ground providing RF de-coupling of the network at RF frequencies.
易迪拓培训 专注于微波 射频 天线设计人才的培养网址 :http://www.edatop.com H F S S 视频培训课程推荐 HFSS 软件是当前最流行的微波无源器件和天线设计软件, 易迪拓培训 (www.edatop.com) 是国内最专业的微波 射频和天线设计培训机构 为帮助工程师能够更好 更快地学习掌握 HFSS 的设计应用, 易迪拓培训特邀李明洋老师主讲了多套 HFSS 视频培训课程 李明洋老师具有丰富的工程设计经验, 曾编著出版了 HFSS 电磁仿真设计应用详解 HFSS 天线设计 等多本 HFSS 专业图书 视频课程, 专家讲解, 直观易学, 是您学习 HFSS 的最佳选择 HFSS 学习培训课程套装该套课程套装包含了本站全部 HFSS 培训课程, 是迄今国内最全面 最专业的 HFSS 培训教程套装, 可以帮助您从零开始, 全面深入学习 HFSS 的各项功能和在多个方面的工程应用 购买套装, 更可超值赠送 3 个月免费学习答疑, 随时解答您学习过程中遇到的棘手问题, 让您的 HFSS 学习更加轻松顺畅 课程网址 :http://www.edatop.com/peixun/hfss/11.html HFSS 天线设计培训课程套装套装包含 6 门视频课程和 1 本图书, 课程从基础讲起, 内容由浅入深, 理论介绍和实际操作讲解相结合, 全面系统的讲解了 HFSS 天线设计的全过程 是国内最全面 最专业的 HFSS 天线设计课程, 可以帮助您快速学习掌握如何使用 HFSS 设计天线, 让天线设计不再难 课程网址 :http://www.edatop.com/peixun/hfss/122.html 更多 HFSS 视频培训课程 : 两周学会 HFSS 中文视频培训课程课程从零讲起, 通过两周的课程学习, 可以帮助您快速入门 自学掌握 HFSS, 是 HFSS 初学者的最好课程, 网址 :http://www.edatop.com/peixun/hfss/1.html HFSS 微波器件仿真设计实例 中文视频教程 HFSS 进阶培训课程, 通过十个 HFSS 仿真设计实例, 带您更深入学习 HFSS 的实际应用, 掌握 HFSS 高级设置和应用技巧, 网址 :http://www.edatop.com/peixun/hfss/3.html HFSS 天线设计入门 中文视频教程 HFSS 是天线设计的王者, 该教程全面解析了天线的基础知识 HFSS 天线设计流程和详细操作设置, 让 HFSS 天线设计不再难, 网址 :http://www.edatop.com/peixun/hfss/4.html 更多 HFSS 培训课程, 敬请浏览 :http://www.edatop.com/peixun/hfss
` 专注于微波 射频 天线设计人才的培养易迪拓培训网址 :http://www.edatop.com 关于易迪拓培训 : 易迪拓培训 (www.edatop.com) 由数名来自于研发第一线的资深工程师发起成立, 一直致力和专注于微波 射频 天线设计研发人才的培养 ; 后于 2006 年整合合并微波 EDA 网 (www.mweda.com), 现已发展成为国内最大的微波射频和天线设计人才培养基地, 成功推出多套微波射频以及天线设计相关培训课程和 ADS HFSS 等专业软件使用培训课程, 广受客户好评 ; 并先后与人民邮电出版社 电子工业出版社合作出版了多本专业图书, 帮助数万名工程师提升了专业技术能力 客户遍布中兴通讯 研通高频 埃威航电 国人通信等多家国内知名公司, 以及台湾工业技术研究院 永业科技 全一电子等多家台湾地区企业 我们的课程优势 : 成立于 2004 年,10 多年丰富的行业经验 一直专注于微波射频和天线设计工程师的培养, 更了解该行业对人才的要求 视频课程 既能达到现场培训的效果, 又能免除您舟车劳顿的辛苦, 学习工作两不误 经验丰富的一线资深工程师讲授, 结合实际工程案例, 直观 实用 易学 联系我们 : 易迪拓培训官网 :http://www.edatop.com 微波 EDA 网 :http://www.mweda.com 官方淘宝店 :http://shop36920890.taobao.com 专注于微波 射频 天线设计人才的培养易迪拓培训官方网址 :http://www.edatop.com 淘宝网店 :http://shop36920890.taobao.com