SafeTANK GR5630-SB3+ User Manual
» SafeTANK GR5630-SB3+ User Manual...1» SafeTANK GR5630-SB3+ 產品使用說明... 7 V1.1
Introduction Thanks for purchasing RAIDON product. This User Manual will introduce you the GR5630- SB3+ storage product. Before using your GR5630-SB3+, please read it thoroughly. Although all information contented in this User manual had already been carefully verified before publishing, however, the actual product and its specification will be based upon the time of delivery from RAIDON. Any update to the product or its relevant information may be listed on www.raidon.com.tw. Product is subjected to change without notice. If you have any question regarding this product, or you would like to know the latest product information, or updates, please contact your local supplier or visit to www.raidon.com.tw for assistance. Copyright RAIDON Technology, Inc. All right is reserved. Table of Contents 1. Package Contents and Product Views 2. Operating Information 3. Hardware Requirements and Precautions 4. Hardware Installation Procedure 5. Description of Front Panel Operation and LCD Information 6. Replacement of Malfunctioning Drive and Data Rebuild Instructions 7. System Temperature Overheat and Fan Failure Management 8. Frequently Asked Questions 1. Package Contents and Product Views Open the package and you shall find the following parts: GR5630-SB3+ GR5630-SB3+ x 1 ( with removable drive tray enclosed x 4) USB 3.0 Cable x 1 esata Cable x 1 AC Power Cable x 1 CD x 1 Screws & Keys Quick Installation Guide x 1 Please make sure that the contents listed above are not damaged or missing. If you find any damaged or missing parts in the package, please contact your supplier immediately. 1
Product View Front View Drive position(1) Drive position(2) Drive position(3) Drive position(4) A. Hard drive status Indicator B. Removable drive tray C. HDD tray key lock D. LCD display E. UP button F. DOWN button G. ENTER button H. ESC button I. Power indicator J. Alarm indicator Rear View K. USB3.0 interface connection L. esata interface connection M. Mute button N. Power Switch O. Power socket P. Cooling fan Q. Anti-theft cord slot 2
LED Indicators : Constant Front LED Power LED Larm LED HDD LED Buzzer Power ON Blue Blue Flashing Blue 1 long when booting finished No HDD Blue Disk Failed Blue Red RAID Failed Blue Red 4 Short Disk Idle Blue Blue Format Blue Blue Flashing Access Blue Blue Flashing Rebuilding - Source Blue Blue Flashing Rebuilding - Target Blue Blue and Purple Flashing Fan Failed Blue Red Blue 4 Short Over Temp Blue Red Blue 4 Short 2. Operating Information Operating Temperature : 10 ~ 35 C (50 ~ 95 F) Storage Temperature : -20 ~ 47 C (-4 ~ 116 F) Relative humidity : 5% to 95% noncondensing Line Voltage : 100~240V AC 3. Hardware Requirements and Precautions 1. Only one interface connection may be used at once per computer system. 2. RAID volume formation utilizes the capacity of whichever hard drive has the smallest and then multiply that capacity by three for RAID 5, four for RAID 0, to form a large volume, therefore, it is recommended to only install hard drives of the same brand and specification for all drive position prior to use. Moreover, when you need to replace with a new hard drive, please be sure to purchase one with the same specification, capacity and brand. If these conditions can t be met, select one that s at least 20 GB greater in capacity. 3. The actual storage capacity of GR5630-SB3+ recognized by the system may differ from the total capacity stated on the hard drives once the drives have been formatted. 4. When connected to the computer system, it s prohibited to remove, insert or swap the hard drive while data transfer is being performed. 5. It s prohibited to change the positioning of the drives once the initial installation has been completed as the changes made to the drive positions may destroy the RAID formation. 6. If you discover that hard drive failure is taking place, go to Section 6 Replacement of Malfunctioning Drive and Data Rebuild Instructions and follow the steps accordingly. 3
7. Whenever turning off or unplugging the GR5630-SB3+ from your computer system becomes necessary, always remember to safely remove it from your operating system first. 8. In RAID 5 mode, the system allows one single hard drive failure. If multiple drive failures occur at once, it s likely that all data stored in the system have been destroyed or lost. In RAID 0 mode, if one hard drive failure occurs, then all data maybe destroyed or lost. If this happens, we recommend you to consult with a professional hard drive data recovery specialist to see if your data may be recoverable. 9. It is highly recommended for users to back up important data contained within the GR5630-SB3+ unit on a regular basis or whenever the user feels necessary to a remote or a separate storage device. RAIDON will not be responsible for any lost of data caused during the use of the unit or the recovery of the data lost. 4. Hardware Installation Procedure Please follow the instructions below to complete the hardware installation. Step 1 Step 2 Step 3 Open the package and take out the product making sure that all the enclosed contentsare not damaged or missing. Should you find damages or missing contents, please contactyour supplier immediately. Place the system on a stable surface. Ensure that it is well ventilated without blockage tothe vent and kept away from areas near water and damage prone areas. Use the key included in the accessory kit and inserted into the key access opening to eject the removable drive tray latch and extract the removable drive tray. Step 4 Mount your hard drives onto the removable drive tray and secure it with the screws included in the accessory kit to avoid any damage to the hard drive due to accidental movements. Step 5 Step 6 Step 7 Step 8 Step 9 When the hard drive installation has been completed, insert the hard drive tray into the system horizontally and secure the latch into place. Connect the AC power cable to the GR5630-SB3+, and then plug the AC power to the wall socket. Boot-up the unit. Set the storage mode using the LCD and buttons on the front (please refer to section 5 for front panel and LCD information). Connect the cable to the PC and the GR5630-SB3+ port. After boot-up, your operating system will automatically detect the storage capacity of your hard drives. Please follow the operating system instructions to configure and format your drives. The formatted drives can be configured for the RAID setup. 4
5. Description of Front Panel Operation and LCD Information Front Panel Operation: Enter: Enter: Enter to next level or Confirm Esc: Back to next level or Cancel Up / Down: Select Items Users can set the RAID mode using the LCD and buttons on the front. The default is JBOD mode. Using Quick Setup function, users can change the RAID mode to RAID 0 or RAID 5 quickly. Please refer to LCD Information as below for other setting: Level 0 Level 1 Level 2 Level 3 Level 4 Quick Setup Create One RAID Delete All RAID RAID 0/ RAID 5 Select Disk Disk 1 Disk Manager Identify Disk Disk 2 Disk 3 Disk 4 Show Disk Info < Disk Info > Identify RAID Select RAID External 4BAY HARDWARE RAID RAID Manager Create RAID Delete RAID RAID Info Change RAID Pwd RAID 0 / RAID 5 Select RAID < Password > for RAID Setup Select Disk Rebuilding Priority Highest/High/Medium/Low/Lowest Standby Timer < 99999min > System Info Firmware Version Changhe Password < Password > for System Info Logout From Menu < Y or N > System Manager Alarm Control Mute the Buzzer Voltage Monitor < 3.3V / 5V / 12V > Hardware Monitor Temp. Monitor Fan Monitor < Temp. > < Fan Speed / Fan Level > 5
6. Replacement of Malfunctioning Drive and Data Rebuild Instructions When a front hard drive indicator has lit up red and the audio alarm sounds, this could mean the indicated hard drive may be malfunctioning. If this occurs, you may press the mute button at the rear of the system to shut off the audio alarm and power off the system immediately if in the allowed operational state, and then re-power on the system to double check and see if in fact the indicated hard drive has malfunctioned. If the problem persists, please turn off the system and follow the directions below : 1. Remove the drive tray containing the malfunctioned hard drive and disassemble the hard drive from drive tray. 2. Mount the new hard drive onto the tray and insert it back to the empty drive position of the GR5630-SB3+, then push the latch into place making sure it is secured and locked. 3. In RAID 5 mode, when you turn the system on, the hard drive status indicator of the replacement drive will interchangeably blink red and purple to inform that the data is being rebuilt to the replacement drive. During data rebuild, you may operate the GR5630-SB3+ as normal. When the indicator stops, the data rebuild process has been completed. 7. System Temperature Overheat and Fan Failure Management If the alarm indicator has lit up red and the audio alarm sounds, this could mean that either a system fan has stopped operating entirely or the system temperature has exceeded over the default temperature of 60 C. When this occurs, you may press the mute button at the rear of the system to shut off the audio alarm and power off the system immediately if in the allowed operational state to let the system cool. Check and see if the overall operation environment is well ventilated and make sure there are no blockages to the enclosed fan and then re-power on the system to continue use. If the problem persists, please turn off the system and contact your supplier or the RAIDON tech support for further assistance. 8. Frequently Asked Questions Q1. Which drive format should I choose to format the hard drives in the GR5630-SB3+? A: It depends on the computer system you most often use. See the below suggestions: 1. Use NTFS format for Windows 2000/XP/Vista/7/8/10 system 2. Use HFS+ (Mac OS Extended) format for a Mac OS X system 3. Choose FAT32 format if you ll use the GR5630 in both Windows and Mac environments (the maximum size of one single file may not exceed 4 GB). Q2. Why can t my GR5630-SB3+ reach the transfer performance speed of 200 MB/s via esata interface as stated on your website? A: 1. Please first check if your PCI-E SATA host adapter would only support PCI-E (1X). This type of host adapters cannot reach the transfer performance speed beyond 135MB/s. 2. The GR5630-SB3+ will need to be set to the RAID 0 mode also. 6
» SafeTANK GR5630-SB3+ 產品使用說明關於這份手冊 感謝您使用 RAIDON 的產品 本手冊將介紹產品 在您開始使用產品前, 建議您先閱讀過本手冊 手冊裡的資訊在出版前雖已被詳細確認, 實際產品規格仍將以出貨時為準 ; 任何產品規格或相關資訊更新請您直接到 www.raidon.com.tw 網站查詢, 本公司將不另行通知 若您想獲得 RAIDON 最新產品訊息 使用手冊 韌體, 或對 RAIDON 產品有任何疑問, 請您聯絡當地供應商或到 www.raidon.com.tw 取得相關訊息 本手冊相關產品內容歸銳銨科技股份有限公司版權所有 目錄索引 1. 產品外觀及包裝內容 2. 環境需求 3. 硬體需求與注意事項 4. 硬體安裝 5. 前面板操做及 LCD 訊息說明 6. 故障硬碟更換步驟及資料重建功能說明 7. 系統過熱及風扇故障排除 8. 常見問題 1. 產品外觀及包裝內容打開包裝外盒後, 包裝內容應包含下列組件 : GR5630-SB3+ GR5630-SB3+ 產品本體 X1( 內含抽取盒 x4) USB3.0 連接線 x1 esata 連接線 x1 AC 電源線 x1 光碟 x 1 螺絲及鑰匙快速安裝導引 x 1 請確認相關配件與產品本身是否有受損或配件缺少, 若有任何疑問請與本產品供應商聯絡 7
正面與背面示意圖 正面圖 硬碟位置 1 硬碟位置 2 硬碟位置 3 硬碟位置 4 A. 2.5 吋硬碟狀態指示燈 B. 硬碟抽取盒 C. 硬碟卡榫按鍵 D. LCM 顯示幕 E. UP 按鍵 F. DOWN 按鍵 G. ENTER 按鍵 H. ESC 按鍵 I. 電源指示燈 J. 系統警示燈 背面圖 K. USB3.0 連接埠 L. esata 連接埠 M. 靜音按鈕 N. 電源開關 O. 電源插座 P. 風扇 Q. 防竊鎖孔 8
燈號一覽表 : 狀態 前置 LED 電源指示燈 系統警示燈 硬碟狀態顯示燈 蜂鳴器 開機 藍燈恆亮 藍燈閃爍 恆亮 啟動完成時 1 長音 無硬碟 藍燈恆亮 硬碟故障 藍燈恆亮 紅燈恆亮 RAID 毀損 藍燈恆亮 紅燈恆亮 4 短音 閒置 藍燈恆亮 藍燈恆亮 格式化 藍燈恆亮 藍燈閃爍 資料存取 藍燈恆亮 藍燈閃爍 資料重建 - 來源碟 藍燈恆亮 藍燈閃爍 資料重建 - 資料碟 藍燈恆亮 藍紫燈交互閃爍 風扇故障 藍燈恆亮 紅燈 藍燈恆亮 4 短音 過熱 藍燈恆亮 紅燈 藍燈恆亮 4 短音 2. 環境需求工作溫度 :10 ~ 35 o C (50 ~ 95 o F) 儲存溫度 :-20 ~ 47 o C (-4 ~ 116 o F) 相對濕度 :5% 至 95% 非冷凝狀態工作電壓 :100~240V AC 3. 硬體需求與注意事項 1. 本系統同一時間只可透過一組介面與一台電腦執行資料傳輸 2. RAID 5 的容量形成是將硬碟中最小容量乘上三倍後,RAID 0 乘上四倍, 之後會被視為一個大儲存容量 ; 因此, 用本系統前必須每顆硬碟裝置槽都已完成硬碟安裝, 並建議全部使用相同品牌與同規格之全新硬碟 同時, 如果需要更換新的硬碟時, 也請您務必購買規格 容量 廠牌相同的硬碟, 若您無法購買到符合上述條件的硬碟時, 請選購容量大於另一硬碟最少 20GB 3. 硬碟格式化後, 由電腦主機作業系統所辨識 GR5630-SB3+ 的實際容量會與硬碟廠所標示的容量加總後, 有所差異 4. 當系統運作時, 請勿任意移除任何一顆硬碟, 以免導致資料遺失 5. 完成系統初始化安裝後, 在使用上請勿任意變更硬碟位置 ; 此動作將可能導致系統無法形成 RAID 6. 當您發現硬碟故障時, 請參考章節 6" 硬碟故障排除與硬碟更換步驟說明 ", 並依照程序進行故障硬碟的更換 7. 當您需要關閉或移除 GR5630-SB3+ 時, 務必透過您所操作的作業系統中執行硬碟安全移除後, 方可進行電源關閉動作 9
8. 在 RAID 5 模式下儲存系統僅容許單顆硬碟故障 因此, 當您發現二顆以上的硬碟顯示故障時, 您先前以儲存的資料可能已損毀或遺失 ; 在 RAID 0 模式下, 當您發現一顆以上的硬碟顯示故障時, 您先前以儲存的資料可能已損毀或遺失 建議您可尋找專業硬碟資料救援服務, 試著將您損毀或遺失的資料重新取回 9. 強烈建議除了使用 GR5630-SB3+ 的資料儲存功能外, 請針對重要資料備份到另一個儲存裝置或遠端備份, 雙重備份您重要的資料 若您儲存在 GR5630-SB3+ 的資料損毀或遺失,RAIDON 將不負任何的責任 4. 硬體安裝 請參照以下步驟完成硬體安裝 步驟 1 步驟 2 步驟 3 拆開外包裝並取出產品主體 ( 請確認相關配件與產品本身是否有受損或是缺少配件, 若有任何疑問, 請與您的經銷商或業務人員聯絡 ) 將系統擺放於穩固平台, 並確認散熱風扇口沒有被其它物體擋住, 系統四周有適當的散熱空間 ( 擺放環境請避免接近潮濕或其它亦對產品造成損傷的環境 ) 請按壓抽取盒面板上的按鈕, 按壓後抽取盒門將會輕彈開啟, 即可將抽取盒取出 步驟 4 將硬碟安裝到抽取盒上, 並以零件包內附的螺絲加以固定, 以避免不必要的移動對硬碟造成傷害 步驟 5 硬碟安裝完成後, 請將抽取盒平移放入主機內, 並關上把手 步驟 6 將 AC Power 電源線與 GR5630-SB3+ 連接, 再將 AC Power 電源線與電源插座連接, 執行開機 步驟 7 透過前方的 LCD 與按鍵來設定您所需求的儲存模式 ( 請參考 " 前面板操作及 LCD 訊息說明 ") 步驟 8 將附件中的連接線分別接到 PC 與 GR5630-SB3+ 的相關連接埠 步驟 9 開機後, 您的作業系統將會自動辨識到 RAID 容量 ; 待辨識成功後, 請依據您所需的儲存格式, 將系統內的硬碟依照作業系統的指示完成格式化 待格式化完成後, 便可直接執行 RAID 系統 10
5. 前面板操做及 LCD 訊息說明 前面板操作 : Enter : 進入下一層或是確認 Esc : 跳回上一層或是取消 Up / Down : 循序選擇項目 使用者可經由面板進行 RAID 操作,GR5630-SB3+ 預設值為 JBOD, 可進入 Quick Setup 快速設定成 RAID 0 或是 RAID 5 模式使用 如需進行其他設定, 則可參考下列 LCD 說明進行操作 : Level 0 Level 1 Level 2 Level 3 Level 4 Quick Setup Create One RAID Delete All RAID RAID 0/ RAID 5 Select Disk Disk 1 Disk Manager Identify Disk Disk 2 Disk 3 Disk 4 Show Disk Info < Disk Info > Identify RAID Select RAID External 4BAY HARDWARE RAID RAID Manager Create RAID Delete RAID RAID Info Change RAID Pwd RAID 0 / RAID 5 Select RAID < Password > for RAID Setup Select Disk Rebuilding Priority Highest/High/Medium/Low/Lowest Standby Timer < 99999min > System Info Firmware Version Changhe Password < Password > for System Info Logout From Menu < Y or N > System Manager Alarm Control Mute the Buzzer Voltage Monitor < 3.3V / 5V / 12V > Hardware Monitor Temp. Monitor Fan Monitor < Temp. > < Fan Speed / Fan Level > 11
6. 故障硬碟更換步驟及資料重建功能說明 1. 取出故障硬碟所存放的抽取盒, 再將硬碟從抽取盒上拆解下來 2. 將新的硬碟安裝至抽取盒後, 再將新硬碟的抽取盒插回 GR5630-SB3+ 空的硬碟槽位置, 並將抽取盒門鎖上, 確認硬碟已完全插入 3. RAID 5 模式下, 將電源打開時, 您將會看到所更換的新硬碟抽取盒旁的指示燈號呈現閃爍紅藍燈的狀態, 表示更換上的硬碟資料正在進行重建 ; 此時, 您仍可正常使用 GR5630-SB3+ 工作 ; 待資料重建指示燈號停止, 即代表資料重建完成 RAID 0 模式下, 因單顆硬碟故障會造成所有資料損毀, 更換新硬碟後, 請重新將系統內的硬碟格式化 7. 系統過熱與風扇故障狀況排除 GR5630-SB3+ 內建故障警示功能, 若 GR5630-SB3+ 內部溫度超過 60, 或 GR5630-SB3+ 風扇發生故障時, 內建的蜂鳴器會發出警告聲響, 前面板的紅色警示燈號也會亮起 ; 此時您可選按系統背面的靜音按鈕, 先將警示聲關閉, 並在允許的狀況下關閉 GR5630-SB3+ 電源讓系統降溫 ; 同時, 請先確認積體擺放環境是否通風良好, 沒有任何物體擋住風扇孔, 一併檢查 GR5630-SB3+ 的風扇是否停止運轉 ; 待上述檢查確認後, 再將電源開啟繼續使用本系統 若問題還是無法獲得解決, 請與供應商或 RAIDON 聯絡, 以便取得進一步的支援 8. 常見問題 Q1. 我應該選擇何種模式來格式化 GR5630-SB3+ 產品內的硬碟? A: 這將取決於您平常所使用的電腦系統, 我們有以下建議 : 1. Windows 2000 / XP / Vista / 7 / 8 / 10 使用 NTFS 2. Mac OS X 使用 HFS+ (Mac OS Extended) 3. 如必須同時使用於 PC 或 Mac, 請使用 FAT32 ( 單一檔案的最大限制是 4GB) Q2. 為什麼我所購買的 GR5630-SB3+ 透過 esata 介面無法達到 200MB/s 以上的傳輸速度? A:1. 請先檢查您所購置的 PCI-E SATA 擴充卡是否僅支援 PCI-E (1X), 此類擴充卡無法達到 135MB/s 以上的傳輸速度 2. GR5630-SB3+ 的儲存模式必須為 RAID 0 或 RAID 5 模式 12
www.raidon.com.tw 13