FEATURE Thin Film Passivity NiCr Resistor Very Tight Tolerance from ±0.01%. Extremely Low TCR from ±5ppm/ Wide R-Value Range Rated : 1/32W ~ 1W (0402 ~2512) Applications Medical Equipment Testing / Measurement Equipment Consumer Product Printer Equipment Automatic Equipment Controller DC-DC Converters, Battery pack, Charge. Communication Device, Cell phone, GPS, PDA Measurement instruments Figure CONSTRUCTION Resistor Layer (RuO2) / 電阻層 Primary Overcoat (Glass) / 保障塗層 ( 玻璃 ) Secondary Overcoat (Epoxy) 表面塗料 ( 環氧樹脂 ) Top Electrode (Ag/Pd) / 上層電極 Alumina Substrate ( 氧化鋁基板 ) External Electrode (Sn) / 外部電極 ( 錫 ) Bottom Electrode (Ag) / 底部電極 ORDERING INFORMATION Example: Y-TPT03FC10R0 (1/16W 0603 ±1% 25ppm 10R Ω ) Part No Resistance Tolerance TCR( ) Standard High Standard High E96 (Ω) 1/16W --- 0402 Y-TPT02 --- A = ±0.01% S=±5ppm 1R=1R00 10K Reel 1/16W 1/10W 0603 Y-TPT03 X-TPT03 P = ±0.05% B=±10ppm 10R=10R0 5K Reel --- 1/6W 0603 --- H-TPT03 B = ±0.1% C=±25ppm 100R=100R 5K Reel 1/10W 1/8W 0805 X-TPT05 W-TPT05 C = ±0.25% D=±50ppm 1K=1001 5K Reel --- 1/4W 0805 --- V-TPT05 D = ±0.5% E=±100ppm 10K=1002 5K Reel 1/8W 1/4W 1206 W-TPT06 V-TPT06 F = ±1% 100K=1003 5K Reel --- 1/3W 1206 --- J-TPT06 1M=1004 5K Reel 1/5W 1/3W 1210 I-TPT10 J-TPT10 10M=1005 5K Reel 1/4W 1/3W 2010 V-TPT20 J-TPT20 5K Reel 1/2W 3/4W 2512 U-TPT12 T-TPT12 4K Reel --- 1W 2512 --- S-TPT12 4K Reel DIMENSION Standard High L W H D1 D2 1/16W --- 0402 1.00 ±0.05 0.50 ±0.05 0.30 ±0.05 0.20 ±0.15 0.20 ±0.15 1/16W 1/10W 0603 1.50 ±0.15 0.80 ±0.15 0.50 ±0.15 0.35 ±0.15 0.35 ±0.15 --- 1/6W 0603 1.50 ±0.15 0.80 ±0.15 0.50 ±0.15 0.35 ±0.15 0.35 ±0.15 1/10W 1/8W 0805 2.00 ±0.20 1.25 ±0.15 0.50 ±0.15 0.35 ±0.15 0.35 ±0.15 --- 1/4W 0805 2.00 ±0.20 1.25 ±0.15 0.50 ±0.15 0.35 ±0.15 0.35 ±0.15 1/8W 1/4W 1206 3.20 ±0.20 2.50 ±0.20 0.55 ±0.15 0.50 ±0.20 0.50 ±0.20 --- 1/3W 1206 3.20 ±0.20 2.50 ±0.20 0.55 ±0.15 0.50 ±0.20 0.50 ±0.20 1/5W 1/3W 1210 3.10 ±0.10 2.50 ±0.20 0.55 ±0.05 0.45 ±0.10 0.40 ±0.10 1/4W 1/3W 2010 5.0 ±0.10 2.50 ±0.10 0.55 ±0.05 0.60 ±0.20 0.40 ±0.10 1/2W 3/4W 2512 6.30 ±0.20 3.20 ±0.20 0.55 ±0.10 0.60 ±0.20 0.60 ±0.20 --- 1W 2512 6.30 ±0.20 3.20 ±0.20 0.55 ±0.10 0.60 ±0.20 0.60 ±0.20 Fig-1 Packing Page: P5 - P1
Standard Electrical Specification: Rated Maximum Voltage Tolerance Range / Resistance Range (Ω) TCR at 70 Operating Overload ±0.01% ±0.05% ±0.1% ±0.25% ±0.5% ±1% ppm/ 1/16W 0402 1/16W 0603 25V 50V 1/2W 2512 150V 300V 50~5K 50~5K 50~5K ±5 50~12K 50~12K 50~12K ±10 50~12K 50~12K 50~68K ±15 10~200K 10~200K 10~200K 10~200K ±25 10~200K 10~200K 1R~200K 1R~200K ±50 25~15K 25~15K 25~15K ±5 25~100K 4.7~332K 4.7~332K ±10 25~100K 4.7~332K 4.7~332K ±15 4.7~332K 4.7~1M 2.2~1M 2.2~1M 2.2~1M ±25 4.7~332K 4.7~1M 1R0~1M 1R0~1M 1R0~1M ±50 25~30K 25~30K 25~30K ±5 25~100K 4.7~510K 4.7~510K ±10 25~100K 4.7~510K 4.7~510K ±15 4.7~510K 4.7~2M 1R0~2M 1R0~2M 1R0~2M ±25 4.7~510K 4.7~2M 1R0~2M 1R0~2M 1R0~2M ±50 25~50K 25~50K 25~50K ±5 4.7~1M 4.7~2.2M 1R~2.2M 1R~2.2M 1R~2.2M ±25 4.7~1M 4.7~2.2M 1R~2.2M 1R~2.2M 1R~2.2M ±50 25~50K 25~50K 25~50K ±5 4.7~1M 4.7~2.2M 1R~2.2M 1R~2.2M 1R~2.2M ±25 4.7~1M 4.7~2.2M 1R~2.2M 1R~2.2M 1R~2.2M ±50 25~100K 25~100K 25~100K ±5 4.7~1M 4.7~3.0M 1R~3.0M 1R~3.0M 1R~3.0M ±25 4.7~1M 4.7~3.0M 1R~3.0M 1R~3.0M 1R~3.0M ±50 25~100K 25~100K 25~100K ±5 4.7~1M 4.7~3.0M 1R~3.0M 1R~3.0M 1R~3.0M ±25 4.7~1M 4.7~3.0M 1R~3.0M 1R~3.0M 1R~3.0M ±50 Operating Temperature Range: -55 ~ +155 * In case resistors operating ambient temperature in excess of the temperature range -55 ~+155 power ratio will be derated in accordance with the figure as shown on the right. * Others data not in the specification of data, please contact us. 如果你要求的規格不在本規格書裡請與我們聯絡. POWER DERATING CURVE 50V 100V 1/10W 0805 100V 200V 1/8W 1206 150V 300V 1/5W 1210 150V 300V 1/4W 2010 150V 300V 100 70 Ratio (%) 80 60 40 20-55 155 0 20 40 60 80 100 120 140 160 Ambient Temperature ( ) Page: P5 - P2
High Electrical Specification: Rated Maximum Voltage Tolerance Range / Resistance Range (Ω) TCR Operating at 70 Operating Overload ±0.01% ±0.05% ±0.1% ±0.25% ±0.5% ppm/ Temp. 50~15K 50~15K 50~15K 50~15K 50~15K ±5 25~100K 4.7~332K 4.7~332K 4.7~332K 4.7~332K ±10 1/10W 0603 75V 150V 25~100K 4.7~332K 4.7~332K 4.7~332K 4.7~332K ±15 25~100K 4.7~332K 4.7~1M 4.7~1M 4.7~1M ±25 25~100K 4.7~332K 4.7~1M 4.7~1M 4.7~1M ±50 1/6W 0603 100V 150V 10~332K 10~332K 10~332K 10~332K ±25,±50 25~30K 25~30K 25~30K 25~30K 25~30K ±5 25~200K 4.7~510K 4.7~510K 4.7~510K 4.7~510K ±10 1/8W 0805 150V 300V 25~200K 4.7~510K 4.7~1M 4.7~1M 4.7~1M ±15 25~200K 4.7~510K 4.7~1M 1R~1M 1R~1M ±25 25~200K 4.7~510K 4.7~1M 1R~1M 1R~1M ±50 1/4W 0805 150V 300V 10R~500K 10R~500K 10R~500K 10R~500K ±25,±50 1/4W 1206 200V 400V 25R~500K 4.7R~1M 4.7R~1M 4.7R~1M 4.7R~1M ±15 1/3W 1206 200V 400V 10R~1M 10R~1M 10R~1M 10R~1M ±25,±50. 1/3W 1210 200V 400V 25R~500K 4.7R~1M 4.7R~1M 4.7R~1M 4.7R~1M ±15 1/3W 2010 200V 400V 25R~500K 4.7R~1M 4.7R~1M 4.7R~1M 4.7R~1M ±15 25R~2K 4.7R~2K 4.7R~2K 1R0~2K 1R0~2K ±10 3/4W 2512 200V 400V 25R~2K 4.7R~2K 4.7R~2K 1R0~2K 1R0~2K ±15 25R~2K 4.7R~2K 4.7R~2K 1R0~2K 1R0~2K ±25 25R~2K 4.7R~2K 4.7R~2K 1R0~2K 1R0~2K ±50 1W 2512 200V 400V 4.7R~100R 1R0~100R 1R0~100R ±25 4.7R~100R 1R0~100R 1R0~100R ±50 * In case resistors operating ambient temperature in excess of the temperature range -55 ~+155 power ratio will be derated in accordance with the figure as shown on the right. * Others data not in the specification of data, please contact us. 如果你要求的規格不在本規格書裡請與我們聯絡. IR Reflow -55 ~ +155 Page: P5 - P3
Tol.±0.01% TCR:±5ppm Test Procedures and Requirements Test Item Test Method Requirement Temperature coefficient of MIL-STD202F Method 304 +25/-55/+25/+125/+25 As specification resistance (T.C.R.) Short time overload JIS-C-5201-1 5.5 Tol.<0.05% ±0.05%; Tol.>0.05% ±0.2% RCWV*2.5 or Max. overload voltage for 5 seconds R±0.2% for high power rating Insulation resistance MIL-STD202F Method 302 Apply 100VDC for min >100M Ω Endurance MIL-STD-202F Method 108A Tol.<0.05% ±0.05%; Tol.>0.0% ±0.2% 70+2, Max.working voltage for 1000hrs >7KΩ R±0.5% with 1.5hrs [ON] and 0.5hrs [OFF] R±0.5% for high power rating Damp heat with load MIL-STD-202F Method 103B Tol.<0.05% ±0.05%; Tol.>0.05% ±0.3% 40+2, 90~95%, R.H. Max working voltage R±0.5% for high power rating for 1000hrs with 1.5hrs [ON] and 0.5hrs [OFF] bending strength JIS-C-5201-1 6.1.4 Tol.<0.05% ±0.05%; Tol.>0.05% ±0.2% Bending amplitude 3mm for 10 seconds Solderability MIL-STD-202F Method 208H 95% min. coverage 245+5 for 3seconds Resistance to soldering heat MIL-STD-202F Method 210E Tol.<0.05% ±0.05%; Tol.>0.05% ±0.2% 245+5 for 10 seconds Dielectric withstand voltage MIL-STD-202F Method 301 By Type Max. overload voltage for 1 minute Thermal shock MIL-STD-202F Method 107G Tol.<0.05% ±0.05%; Tol.>0.05% ±0.25% -55 ~155, 100 cycles. Low temperature operation JIS-C-5201-1 7.1 Tol.<0.05% ±0.05%; Tol.>0.05% ±0.2% 1 hour, -65, followed by 45 min. of RCWV. R±0.5% for high power rating Storge temperature: 25±3 ; Humidity <80%RH. VOLTAGE RATING OR CURRENT RATING Resistance Range: 1Ω Rated Voltage: The resistor shall have a DC continuous working voltage or a RMS AC continuous working voltage at commercial-line frequency and wave form corresponding to the power rating, as determined formula as following: E=Rated voltage(v) E= R P P= rating(w) R=Nominal resistance(ω) Overload voltage(v) 2.5* R*P Page: P5 - P4
RECOMMEND LAND PATTERN DESIGN (For Reflow Soldering) Unit: mm Type TPT02 TPT03 TPT05 TPT06 TPT10 TPT12 TPT20 TPT28 TPT12 Dim. 0402 0603 0805 1206 1210 1812 2010 1218 2512 A 0.5 0.8 1.30 2.20 2.00 3.11 3.80 2.04 4.90 B 0.6 0.9 1.40 1.70 2.70 3.00 2.70 4.50 3.40 C 1.5 2.8 2.90 4.20 4.40 5.91 6.60 4.24 8.10 PACKAGE SPECIFICATION Quantity(ea) Standard High Paper Reel Tape In Box Carton 1/16W --- 0402 10,000 Pcs 7" Reel 100K pcs 600K pcs 1/16W 1/10W 0603 5,000 Pcs 7" Reel 50K pcs 300K pcs 1/10W 1/8W 0805 5,000 Pcs 7" Reel 50K pcs 300K pcs 1/8W 1/4W 1206 5,000 Pcs 7" Reel 40K pcs 300K pcs 1/5W 1/3W 1210 5,000 Pcs 7" Reel 40K pcs 300K pcs 1/4W 1/3W 2010 5,000 Pcs 7" Reel 40K pcs 300K pcs 1/2W 3/4W 2512 4,000 Pcs 7" Reel 40K pcs 240K pcs --- 1W 2512 4,000 Pcs 7" Reel 40K pcs 240K pcs Paper Reel Tape Reel Tape Leble Carton Pack In Box Page: P5 - P5