NORMAL CURRENT CONDITION UL type fuse: Max.current de-rating of fuse(in)= R.M.S current/(temp.factor) x UL margin(0.75 fixed) IEC type fuses: Max.curr

Transcription

1 FUSES What are fuses? They are protectors that prevent electronic and electrical equipment from overload current damage.current flew to circuit via fuse until over the specifications of fuse.at That time, the fuse "Blows" and stops the current. FUSE TYPE There are four basic types of fuses: (1)Slow Blow/Time lag fuses ()Dual element slow blow fuses (3)Fast acting fuses (4)Very fast acting fuses Slow-blow fuses are ideal for circuits with a transient surge or power-on inrush.these circuits include:motors,transformers, incandescent lamps and capacitate loads. Fast-acting fuses response quickly and are used in circuits without transient inrush currents. Very fast-acting fuses often have silver linked. Because the fuses need to have ability to limit the current,these fuses are usually used to protect semiconductor circuits. FUSE SELECTION GUIDE The fuse must carry the normal load current of the circuit without nuisance openings.however,when an over current occurs the fuse must interrupt the over current,limit the energy let-through,and withstand the voltage across the fuse during acting.to properly select a fuse the followings must be considered: (1)Normal operating current(the current rating of a fuse is typically derated 5% for operation at 5% to avoid nuisance blowing.for example,a fuse with 10A current rating is not usually recommended for operation at more than 7.5A in a 5% derating.) ()Overload current and melting time of the fuse. (3)Application volage(ac or DC voltage). (4)Inrush currents,surge currents,pulses,start-up currents characteristics. (5)Ambient temperature. (6)Applicable standards agency required,such as UL,CSA, TUV,VDE,PSE and IEC... Considerations: Reduce installed cost,ease of removal, (7)mounting type/form factor,etc. Electrical Characteristic The capacity of fuses for carrying current are tested at 5 and will be affected by ambient temperature changed.the fuse operated in higher the ambient temperature;the life of the fuse will be reduced. Conversely,operating at a lower temperature wil extend the life of fuse.

2 NORMAL CURRENT CONDITION UL type fuse: Max.current de-rating of fuse(in)= R.M.S current/(temp.factor) x UL margin(0.75 fixed) IEC type fuses: Max.current de-rating of fuse(in) = measured rms current/(temp.factorx IEC margin(0.9 fixed)) PERCENT RATING CHART SHOWING EFFECT OF AMBIENT TEMPERATURE ON CURRENT-CARRYING CAPACITY BREAKING CAPACITY A fuse will be safely interrupt in the maximum current and the maximum rated voltage(include less than maximum rated) then the appearance of fuse will not be changed. VOLTAGE RATING For general circuit protetion,the voltage rating of the circuit needs to be equal or less than the voltage rating of the fuse. Using exceed the voltage rating of the fuse in circuit will reduce ability of the fuse for clearing overload current safely.for example, fuse 50V voltage rating can be used in less than 50V circuits. AMPERE SQUARE SECONDS, I t Ii is the measure of heat energy developed within a circuit during the fuse's clearing.it can be expressed as "melting I t ","arcing I t " or the sum of them as " Clearing I t "."I" stands for effective let-through current(rms),which is squared, and "t" means melting time(seconds). I t I t I t I t

3 CALCULATING PULSE I t I t The energy contained in a current pulse depends on the Pulse s waveform s shape, peak current and duration. Determini the energy contained in a particular waveform can be very difficult. Table 1 presents a variety of waveforms and the corresponding formulas which determine I t value. Current pulses in most applications can be approximated by one of the waveforms in Table 1. If a complex waveform is not shown exactly, then it may be possible to break the com-plex waveform in to a combination of the simpler waveforms shown. The complex waveform s I t is then estimated as the sum of the I t values of these other waveforms. The best way to explain how this is done is through an example. Table 1 Waveform I t Formulas Pulse Waveforms Formulas 1 a t b 1 (i a I t= +i ai b+i b )t 3 ip t 1 I t= i p t 3 3 ip t 1 I t= i p t 4 ip t I t=i p t 5 ip t I t= i p t 1 6 ip t OR t I t= i p t 5 1 Table 1 Waveform I t Formulas Pulse Cycle Withstand Capability 100,000 Pulses Pulse I t=% Of Nominal Melting I t 10,000 Pulses Pulse I t=9% Of Nominal Melting I t 1,000 Pulses Pulse I t=38% Of Nominal Melting I t 100 Pulses Pulse I t=48% Of Nominal Melting I t

4 Number of Pulses 1000 Number of Pulses % Table Pulse I t / Average Melting I t 100% Note: Adequate time(10 seconds) must exist between pulse events to allow heat from the previous event to dissipate. Example: Select one fuse Type: MET(page 4) is capable of withstanding 100,000 pulses cycle. The normal operating current is A at an ambient temperature of 5ºC and waveform shown in Figure 1. 10A/div % Table Pulse I t / Average Melting I t 10A/div 100% ip=55a ip=55a Figure 1 t=6ms ms/div t=6ms ms/div Answer: Step1. Refer to table 1 and select suitable pulse waveforms and formulas to calculate I t. I t = 1/3 (ip) t = 1/3 x (55) x = 6.05A Sec This value is referred to as the Pulse I t Step. Refer to table decide Nominal Melting I t. 100,000 Pulses Pulse I t =% Of Nominal Melting I t So: Normal Melting I t = Pulse I t 0. = = 7.5 A Sec Step 3. Examine the I t rating data for the Time lag radial lead micro fuse. The part number MET, ampere design is rated at 31A Sec, which is the minimum fuse rating that will accommodate the 7.5 A Sec calculated in Step. I t I t = 1/3 (ip) t = 1/3 x (55) x = 6.05A Sec I t I t I t I t I t = Pulse I t 0. = = 7.5 A Sec I t Sec Sec

5 VICFUSE circuit protection design combines miniature Fuses,Fuse Bases and Fuse-Carriers.We provide to you good combinations according to your different demands.for example,a fuse clip or holder is suitable for fuse without lead wire connect with pcb,it's easy for user change and fix it. The Fuse-Holder must be thinking about the maximum energy dissipation (temperature raise) of the application and must check especially in installment about the temperature raise in the maximum ambient temperature. Please ask for further detailed information for choice and application of our Fuse-Links. RETURN OF GOODS Return of unused merchandise is permitted within 30 days after shipment only,with freight and duty paid.a returning fee equal to 15% of the original sales price (minimum of US $100)will be charged for this service,consult with sales department for authorization prior to returning merchan dise for credit or replacement.an authorization number must be appeared on all packages returned or they will not be accepted. VICFUSE Components are guaranteed from defects in material and workmanship for a reason able period of time after delivery. Our liability shall be limited to replacement to defective material only. Either seller or manufacturer shall be liable for any injury,loss or damage,direct or consequential,rising out of the use of or the inability to use the products. Before using,user shall determine the suitability of the product for his intended use,user assumes all risk and liability whatsoever in connection therewith. VICFUSE reserves the right to change specifications on any and all items shown in this catalog.

6 FUSE SELECTION INDEX PRODUCT TYPE CHARACTERISTICS A V SURFACE MOUNT FUSE F SEF 6mA-5A 15V,86V T SET 00mA-7A 15V C TYPE CHIP FUSE F CQ40LF 500mA-40A 600V 1-13 T CQ40LT 500mA-40A 600V F CQ4LF 1A-0A 350V T CQ4LT 1A-0A 350V FF CQ1LV 1A-0A 15V,4V T CQ1LH 1A-0A 15V,4V F CQ1LF 1A-0A 15V,4V T CQ1LT 1A-0A 15V,4V F CQ06LF 1A-8A 63V T CQ06LT 1A-8A 63V P TYPE CHIP FUSE F CQ4PF 500mA-1A 350V T CQ4PT 500mA-1A 350V F CQ1PF 500mA-7A 63V T CQ1PT 500mA-7A 63V F CQ06PF 500mA-5A 63V T CQ06PT 500mA-5A 63V THIN FILM CHIP FUSE H CF1 500mA-7A 63V,3V H CF06 400mA-5A 50V,3V H CF04 315mA-4A 3V F CFS1 500mA-7A 63V,3V F CFS06 400mA-6A 50V,3V F CFS04 500mA-4A 3V F CP1 500mA-7A 63V,3V F CP06 500mA-5A 50V,3V F CP04 500mA-4A 3V T CPS1 500mA-7A 63V,3V 6-63 T CPS06 500mA-6A 50V,3V PPTC RESETABLE FUSE PPTC SMD A-3A 6V-60V PPTC SMD 181 PPTC SMD 110 PPTC SMD 106 PPTC SMD 0805 PPTC SMD 0603 PPTC LO RHO SMD 181 PPTC LO RHO SMD 110 PPTC LO RHO SMD 106 PPTC LO RHO SMD 0805 PPTC LO RHO SMD A-3A 0.05A-A 0.05A-A 0.1A-1A 0.01A-0.A 1.4A-3.7A 1.75A-3.80A 0.5A-A 0.75A-1.75A 0.5A-0.75A 6V-60V 6V-60V 6V-60V 6V-15V 9V-60V 6V 6V 6V 6V 6V-9V

7 VICFUSE(CQ) BUSSMANN LITTELFUSE bel AEM SEF 615FA 451/453 SSQ AF 410 SET 615TD 45/454 SST CQ40LF CQ40LT CQ4LF CQ4LT CQ1LV CQ1LH CQ1LF 316FF 466/437/433/49 C1Q F106FA CQ1LT 316TD 469/430/468 C1S F106SB CQ06LF 0603FA 467/438/434/431 CQ F0603FA CQ06LT F0603SB CQ4PF CQ4PT CQ1PF CQ1PT CQ06PF CQ06PT CF CF CF CFS CFS CFS CP CP CP CP CPS CPS PPTC SMD Raychem/Tyco Bourns PPTC SMD PPTC SMD PPTC SMD PPTC SMD PPTC SMD PPTC LO RHO SMD L - PPTC LO RHO SMD L - PPTC LO RHO SMD L - PPTC LO RHO SMD PPTC LO RHO SMD minismd microsmd nanosmd MF-MSMD(F) MF-USMD(F) MF-NSMD(F)

8 Type SEF Fast Acting Square Ceramic Surface Mount Fuse Feature a. Small volume. b. Excellent inrush current withstanding capability. c. Excellent withstand capacity for thermal and mechanic shock. d. High reliability and stable solderability, terminal caps can choice plating gold or silver. e. Our SEF SET series products,because the materials used in these fuses include high melting temperature type solder and this solder contains more than 85% lead (Pb),so these products can conform to the exempts of the requirements of RoHS Directive(00/95/EC). Cartridge Catalog Number SEF.06 Approval PSE Certified products for U.S. and Canada Recognized Component for Canada and U.S. CSA Listed Electrical Characteristic Rated current Ampere [ In ] 6mA (1/16A) 1 ln ln MIN MAX 6mA~10A 4hr 5 sec 1A~15A 4hr 60 sec Environmental Temperature at 5 C Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec SEF ma SEF ma SEF ma SEF ma SEF ma SEF ma SEF ma SEF ma SEF ma SEF ma SEF ma SEF A 15V SEF A SEF 00 A SEF.50.5 A SEF A SEF A SEF A SEF A SEF A SEF A SEF A SEF A SEF A SEF 01 1A SEF A 86V SEF 00 0A SEF 05 5A 1A~15A 6mA~5A 6A~5A 6mA~10A Interrupting 6mA~8A: 1A~5A: 50 amperes at 15V AC/DC 300 amperes at 3V DC 10A: 35 amperes at 15V AC 50 amperes at 15V AC/DC 300 amperes at 3V DC 50 amperes at 65V AC/DC 300 amperes at 4V DC 00 amperes at 86V AC/DC Mechanical Dimension Physical Specification Material Body: Ceramic Terminations: Silver Plated Brass Caps -G:Gold plated brass caps Packaging 1,000 Fuses in 7 inches dia. reel, or 5,000 fuses in 13 inches dia. reel, 1mm wide tape, per EIA Standard 481 Environmental Specification Operating Temperature -55 C to +15 C Vibration MIL-STD-0G, Method 01 (10-55 Hz, 0.06 inch, total excursion) Salt Spray MIL-STD-0G, Method 101, Test Condition B (48Hrs) Insulation Resistance MIL-STD-0G, Method 30, Test Condition A Resistance to Solder Heat MIL-STD-0G, Method 10, Test Condition B (10sec, at 60 C) Thermal Shock MIL-STD-0G, Method 107, Test Condition B (-65 C to +15 C).6 ± 0.1 mm

9 Temperature Temperature Rerating Curve Average Time Current Curves Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Time in Seconds CURRENT IN AMPERES 6mA 80mA 100mA 15mA 00mA 50mA 300mA 375mA 400mA 500mA 700mA 750mA 1A 1.5A A.5A 3A 3.5A 4A 5A 6A 7A 8A 10A 1A 15A Soldering Parameters Reflow Condition - Temperature Min (T s(min) ) 150 C Pb Free assembly T P Ramp-up t P Critical Zone TL to TP Pre Heat - Temperature Max (T s(max) ) 00 C - Time (Min to Max) (t s ) secs T L T S(max) t L Average ramp up rate (Liquidus Temp (T L ) to peak 5 C/second max. T S(min) Preheat Ramp-down T S(max) to T L - Ramp-up Rate 5 C/second max. t S - Temperature (T L ) (Liquidus) 17 C Reflow - Temperature (t L ) seconds Peak Temperature (T P ) 50 +0/-5 C 5 time to peak temperature (t 5ºC to peak) Time Time within 5 C of actual peak Temperature (t p ) 0 40 seconds Ramp-down Rate 5 C/second max. Time 5 C to peak Temperature (T P ) 8 minutes max. Do not exceed 60 C Wave Soldering Parameters 60 C Peak Temperature, 10 seconds max (.70") 3.15 (.14") SEF (.077").95 (.116") Recommended pad layout SERIES AMP Code Refer to Electrical

10 Type SET Slow Blow Square Ceramic Surface Mount Fuse Feature a. Small volume. b. Excellent inrush current withstanding capability. c. Excellent withstand capacity for thermal and mechanic shock. d. High reliability and stable solderability, terminal caps can choice plating gold or silver. e. Our SEF SET series products,because the materials used in these fuses include high melting temperature type solder and this solder contains more than 85% lead (Pb),so these products can conform to the exempts of the requirements of RoHS Directive(00/95/EC). Cartridge Catalog Number SET.00 Approval PSE 1A~7A UL Recognized 00mA~7A CSA Listed 00mA~7A Electrical Characteristic Rated current Ampere [ In ] 00 ma 1 ln ln 3 ln 8 ln MIN MIN MAX MIN MAX MIN MAX 00mA~7A 4hr 1 sec 60 sec 0. sec 3 sec 0.0 sec 0.1 sec Environmental Temperature at 5 C Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec SET ma SET ma SET ma SET ma SET ma SET ma SET ma SET ma SET ma SET A 15V SET A SET 00 A SET.50.5 A SET A SET A SET A SET A SET A SET A SET A Interrupting 50 amperes at 15V AC/DC 300 amperes at 3V DC Mechanical Dimension Physical Specification Material Body: Ceramic Terminations: Silver Plated Brass Caps -G:Gold plated brass caps Packaging 1,000 Fuses in 7 inches dia. reel, or 5,000 fuses in 13inches dia. reel, 1mm wide tape, per EIA Standard 481 Environmental Specification Operating Temperature -55 C to +15 C Vibration MIL-STD-0G, Method 01 (10-55 Hz, 0.06 inch, total excursion) Salt Spray MIL-STD-0G, Method 101, Test Condition B (48Hrs) Insulation Resistance MIL-STD-0G, Method 30, Test Condition A Resistance to Solder Heat MIL-STD-0G, Method 10, Test Condition B (10sec, at 60 C) Thermal Shock MIL-STD-0G, Method 107, Test Condition B (-65 C to +15 C).6 ± 0.1 mm 47

11 Temperature Temperature Rerating Curve Average Time Current Curves Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Time in Seco mA 50mA 300mA 350mA 375mA 400mA 450mA 500mA 700mA 750mA 1A 1.5A A.5A 3A 3.5A 4A 5A 6A 7A CURRENT IN AMPERES Soldering Parameters Reflow Condition - Temperature Min (T s(min) ) 150 C Pb Free assembly T P Ramp-up t P Critical Zone TL to TP Pre Heat - Temperature Max (T s(max) ) 00 C - Time (Min to Max) (t s ) secs T L T S(max) t L Average ramp up rate (Liquidus Temp (T L ) to peak 5 C/second max. T S(min) Preheat Ramp-down T S(max) to T L - Ramp-up Rate 5 C/second max. t S - Temperature (T L ) (Liquidus) 17 C Reflow - Temperature (t L ) seconds Peak Temperature (T P ) 50 +0/-5 C 5 time to peak temperature (t 5ºC to peak) Time Time within 5 C of actual peak Temperature (t p ) 0 40 seconds Ramp-down Rate 5 C/second max. Time 5 C to peak Temperature (T P ) 8 minutes max. Do not exceed 60 C Wave Soldering Parameters 60 C Peak Temperature, 3 seconds max (.70") 3.15 (.14") SERIES SET (.077").95 (.116") Recommended pad layout AMP Code Refer to Electrical

12 Type CQ40LF 10.1mmx 3.1mm (401) Fast-Acting Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 1A ~30A Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Recommended Land Pattern Cartridge Catalog Number CQ40LF.500 CQ40LF1.5 CQ40LF00 CQ40LF00 CQ40LF030 CQ40LF040 Approval UL Recognized 1A~30A Ampere [ In ] 500 ma 1.5A A 0A 30A 40A Electrical Characteristic Voltage ( V ) 600V AC 350V DC Nominal Nominal Resistance Melting I t Cold Ohms A Sec Tape and Reel Specification Item W P E F P D D1 Criterion Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Reflow Solder L1 L W 1A~30A Rated current 1 ln ln MIN MAX 1A~30A 4 hr 5 sec Item P0 10P0 A0 B0 K0 t Criterion Tolerence ±0.10 ±0.0 ±0.10 ±0.10 ±0.10 ±0.05 Environmental Temperature at 5 C Interrupting 1A~30A : 150 amperes at 350V DC 150 amperes at 600V AC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Tape & Reel Quantity 1000 pcs/reel Environmental Specification Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

13 Temperature Temperature Rerating Curve Average Time Current Curves Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Soldering Parameters Reflow Condition - Temperature Min (T s(min) ) 150 C Pb Free assembly T P Ramp-up t P Critical Zone TL to TP Pre Heat - Temperature Max (T s(max) ) 00 C - Time (Min to Max) (t s ) secs T L T S(max) t L Average ramp up rate (Liquidus Temp (T L ) to peak 5 C/second max. T S(min) Preheat Ramp-down T S(max) to T L - Ramp-up Rate 5 C/second max. t S Reflow - Temperature (T L ) (Liquidus) 17 C - Temperature (t L ) seconds Peak Temperature (T P ) 50 +0/-5 C 5 time to peak temperature (t 5ºC to peak) Time Time within 5 C of actual peak Temperature (t p ) 0 40 seconds Ramp-down Rate 5 C/second max. Time 5 C to peak Temperature (T P ) 8 minutes max. Do not exceed 60 C Wave Soldering Parameters 60 C Peak Temperature, 10 seconds max. CQ40LF 001 SERIES AMP Code Refer to Electrical

14 Type CQ40LT 10.1mmx 3.1mm (401) Slow Blow Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 0.5A ~40A Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Recommended Land Pattern Cartridge Catalog Number CQ40LT001 CQ40LT00 CQ40LT00 CQ40LT030 CQ40LT040 Ampere [ In ] 1A A 0A 30A 40A Voltage ( V ) 600V AC 350V DC Nominal Nominal Resistance Melting I t Cold Ohms A Sec L1 L W 1A~30A Approval UL Recognized 0.5A~40A Electrical Characteristic Rated current Environmental Temperature at 5 C Interrupting 0.5A~30A: 150 amperes at 350V DC 150 amperes at 600V AC 600 amperes at 60V DC 40A : 600 amperes at 60V DC Soldering Method 1 ln ln 3 ln 8 ln MIN MIN MAX MAX MAX 0.5mA~40A 4hr 1 sec 60 sec 3 sec 0.1 sec *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Tape and Reel Specification Item W P E F P D D1 Criterion Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Item P0 10P0 A0 B0 K0 t Criterion Tolerence ±0.10 ±0.0 ±0.10 ±0.10 ±0.10 ±0.05 Reflow Solder Tape & Reel Quantity 1000 pcs/reel Environmental Specification Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

15 Temperature Temperature Rerating Curve Average Time Current Curves Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Soldering Parameters Reflow Condition - Temperature Min (T s(min) ) 150 C Pb Free assembly T P Ramp-up t P Critical Zone TL to TP Pre Heat - Temperature Max (T s(max) ) 00 C - Time (Min to Max) (t s ) secs T L T S(max) t L Average ramp up rate (Liquidus Temp (T L ) to peak 5 C/second max. T S(min) Preheat Ramp-down T S(max) to T L - Ramp-up Rate 5 C/second max. t S - Temperature (T L ) (Liquidus) 17 C Reflow - Temperature (t L ) seconds Peak Temperature (T P ) 50 +0/-5 C 5 time to peak temperature (t 5ºC to peak) Time Time within 5 C of actual peak Temperature (t p ) 0 40 seconds Ramp-down Rate 5 C/second max. Time 5 C to peak Temperature (T P ) 8 minutes max. Do not exceed 60 C Wave Soldering Parameters 60 C Peak Temperature, 10 seconds max. CQ40LT 001 SERIES AMP Code Refer to Electrical

16 Type CQ4LF 6.1mmx.6mm (410) Fast-Acting Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 1A ~0A Catalog Number Approval Ampere [ In ] 1 A Voltage ( V ) Nominal Resistance Cold Ohms Nominal Melting I t A Sec CQ4LF CQ4LF A CQ4LF 00 A CQ4LF.50.5 A CQ4LF A CQ4LF A CQ4LF A CQ4LF 004 4A CQ4LF 005 5A 350V CQ4LF 006 6A CQ4LF A CQ4LF 007 7A CQ4LF 008 8A CQ4LF A CQ4LF 01 1A CQ4LF A CQ4LF 00 0A Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Tape and Reel Specification Item W P E F P D D1 Criterion Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Item P0 10P0 A0 B0 K0 t Criterion Tolerence ±0.10 ±0.0 ±0.10 ±0.10 ±0.10 ±0.05 Recommended Land Pattern L1 L W 1A~0A Reflow Solder UL Recognized 1A~0A Electrical Characteristic Rated current 1 ln ln MIN MAX 1A~0A 4 hr 5 sec Environmental Temperature at 5 C Interrupting 1A~0A : 100 amperes at 350V AC 100 amperes at 15V AC 100 amperes at 15V DC 300 amperes at 3V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Tape & Reel Quantity Environmental Specification 500 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

17 Temperature Rerating Curve Average Time Current Curves Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Time in Seconds (s) Current in Amperes (A) Soldering Parameters CQ4LF 001 SERIES AMP Code Refer to Electrical

18 Type CQ4LT 6.1mmx.6mm (410) Slow Blow Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 1A ~0A Catalog Number Approval Ampere [ In ] 1 A Voltage ( V ) Nominal Resistance Cold Ohms Nominal Melting I t A Sec CQ4LT CQ4LT A CQ4LT 00 A CQ4LT.50.5 A CQ4LT A CQ4LT A CQ4LT A CQ4LT 004 4A CQ4LT 005 5A 350V CQ4LT 006 6A CQ4LT A CQ4LT 007 7A CQ4LT 008 8A CQ4LT A CQ4LT 01 1A CQ4LT A CQ4LT 00 0A Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Tape and Reel Specification Item W P E F P D D1 Criterion Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Item P0 10P0 A0 B0 K0 t Criterion Tolerence ±0.10 ±0.0 ±0.10 ±0.10 ±0.10 ±0.05 Recommended Land Pattern Reflow Solder L1 L W 1A~0A UL Recognized 1A~0A Electrical Characteristic Rated 1 ln ln 3 ln 8 ln current MIN MIN MAX MAX MAX 1A~0A 4hr 1 sec 60 sec 3 sec 0.1 sec Environmental Temperature at 5 C Interrupting 1A~0A : 100 amperes at 350V AC 100 amperes at 15V AC 100 amperes at 15V DC 300 amperes at 3V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Tape & Reel Quantity Environmental Specification 500 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

19 Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) 1A 1.5A A.5A 3A 3.5A 4A 5A 6A 7A 8A 10A 1A 15A 0A Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Current in Amperes (A) Soldering Parameters CQ4LT 001 SERIES AMP Code Refer to Electrical

20 Type CQ1LV 3.1mmx 1.6mm (106) Very Fast-Acting Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 1A ~0A Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Recommended Land Pattern Catalog Number Approval Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CQ1LV 001 H 1A CQ1LV 1.50 K 1.5A CQ1LV 00 N A CQ1LV.50 O.5A CQ1LV 003 P 3A CQ1LV 3.50 R 3.5A 15V CQ1LV 004 S 4A CQ1LV 005 T 5A CQ1LV 006 U 6A CQ1LV 007 V 7A CQ1LV 008 W 8A CQ1LV A CQ1LV A V CQ1LV A CQ1LV A Tape and Reel Specification Item W P E F P D D1 Criterion Tolerence ±0.30 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Item P0 10P0 A0 B0 K0 t Criterion Tolerence ±0.10 ±0.0 ±0.10 ±0.10 ±0.10 ± ± 0. mm Reflow Solder UL Recognized 1A~0A Electrical Characteristic Rated current Environmental Temperature at 5 C Interrupting 1A~8A : 50 amperes at 15V AC 50 amperes at 15V DC 100 amperes at 63V DC 150 amperes at 3V AC 10A~0A : 150 amperes at 4V DC Soldering Method 1 ln.5 ln 4 ln MIN MAX MAX 1A~0A 4 hr 5 sec 0.05 sec *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max mm Tape & Reel Quantity Environmental Specification 4000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability Reference IEC

21 Temperature Rerating Curve Average Time Current Curves Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Soldering Parameters CQ1LV 001 SERIES AMP Code Refer to Electrical

22 Type CQ1LH 3.1mmx 1.6mm (106) Slow Blow Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 1A ~0A Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CQ1LH 001 H 1A CQ1LH 1.50 K 1.5A CQ1LH 00 N A CQ1LH.50 O.5A CQ1LH 003 P 3A CQ1LH 3.50 R 3.5A 15V CQ1LH 004 S 4A CQ1LH 005 T 5A CQ1LH 006 U 6A CQ1LH 007 V 7A CQ1LH 008 W 8A CQ1LH A CQ1LH A V CQ1LH A CQ1LH A Approval Tape and Reel Specification Item W P E F P D D1 Criterion Tolerence ±0.30 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Item P0 10P0 A0 B0 K0 t Criterion Tolerence ±0.10 ±0.0 ±0.10 ±0.10 ±0.10 ± ± 0. mm Reflow Solder UL Recognized 1A~0A Electrical Characteristic Rated current 1 ln ln 3 ln 8 ln MIN MIN MAX MAX MAX 1A~0A 4hr 1 sec 10 sec 3 sec 0.05 sec Environmental Temperature at 5 C Interrupting 1A~8A : 50 amperes at 15V AC 50 amperes at 15V DC 100 amperes at 63V DC 150 amperes at 3V AC 10A~0A : 150 amperes at 4V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max mm Tape & Reel Quantity Environmental Specification 4000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability Reference IEC

23 Temperature Rerating Curve Average Time Current Curves Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Soldering Parameters CQ1LH 001 SERIES AMP Code Refer to Electrical

24 Type CQ1LF 3.1mmx 1.6mm (106) Fast-Acting Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 1A ~0A Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Recommended Land Pattern Catalog Number Approval Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CQ1LF 001 H 1A CQ1LF 1.50 K 1.5A CQ1LF 00 N A CQ1LF.50 O.5A CQ1LF 003 P 3A CQ1LF 3.50 R 3.5A 15V CQ1LF 004 S 4A CQ1LF 005 T 5A CQ1LF 006 U 6A CQ1LF 007 V 7A CQ1LF 008 W 8A CQ1LF A CQ1LF A V CQ1LF A CQ1LF A Tape and Reel Specification Item W P E F P D D1 Criterion Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Item P0 10P0 A0 B0 K0 t Criterion Tolerence ±0.10 ±0.10 ±0.10 ±0.10 ±0.10 ± ± 0. mm Reflow Solder UL Recognized 1A~0A Electrical Characteristic Rated current Environmental Temperature at 5 C Interrupting 1A~8A : 50 amperes at 15V AC 50 amperes at 15V DC 100 amperes at 63V DC 150 amperes at 3V AC 10A~0A : 150 amperes at 4V DC Soldering Method 1 ln.5 ln 4 ln MIN MAX MAX 1A~0A 4 hr 5 sec 0.05 sec *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max mm Tape & Reel Quantity Environmental Specification 3000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

25 Temperature Rerating Curve Average Time Current Curves 1A 1.5A A.5A 3A 3.5A 4A 5A 6A 7A 8A 10A 1A 15A 0A Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Time in Seconds (s) Current in Amperes (A) Soldering Parameters CQ1LF 001 SERIES AMP Code Refer to Electrical

26 Type CQ1LT 3.1mmx 1.6mm (106) Slow Blow Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 1A ~0A Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CQ1LT 001 H 1A CQ1LT 1.50 K 1.5A CQ1LT 00 N A CQ1LT.50 O.5A CQ1LT 003 P 3A CQ1LT 3.50 R 3.5A 15V CQ1LT 004 S 4A CQ1LT 005 T 5A CQ1LT 006 U 6A CQ1LT 007 V 7A CQ1LT 008 W 8A CQ1LT A CQ1LT A V CQ1LT A CQ1LT A Approval Tape and Reel Specification Item W P E F P D D1 Criterion Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Item P0 10P0 A0 B0 K0 t Criterion Tolerence ±0.10 ±0.10 ±0.10 ±0.10 ±0.10 ± ± 0. mm Reflow Solder UL Recognized 1A~0A Electrical Characteristic Rated current 1 ln ln 3 ln 8 ln MIN MIN MAX MAX MAX 1A~0A 4hr 1 sec 10 sec 3 sec 0.05 sec Environmental Temperature at 5 C Interrupting 1A~8A : 50 amperes at 15V AC 50 amperes at 15V DC 100 amperes at 63V DC 150 amperes at 3V AC 10A~0A : 150 amperes at 4V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max mm Tape & Reel Quantity Environmental Specification 3000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability

27 Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) 1A 1.5A A.5A 3A 3.5A 4A 5A 6A 7A 8A 10A 1A 15A 0A Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Current in Amperes (A) Soldering Parameters CQ1LT 001 SERIES AMP Code Refer to Electrical

28 Type CQ06LF 1.6mmx 0.8mm (0603) Fast-Acting Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 1A ~8A Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CQ06LF 001 H 1A CQ06LF 1.50 K 1.5A CQ06LF 00 N A CQ06LF.50 O.5A CQ06LF 003 P 3A CQ06LF 3.50 R 3.5A 63V CQ06LF 004 S 4A CQ06LF 005 T 5A CQ06LF 006 U 6A CQ06LF 007 V 7A CQ06LF 008 W 8A Approval UL Recognized 1A~8A Electrical Characteristic Tape and Reel Specification Item W P E F P D D1 Criterion Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Item P0 10P0 A0 B0 K0 T Criterion Tolerence ±0.10 ±0.0 ±0.10 ±0.10 ±0.10 ± ± 0. mm Reflow Solder Rated current 1 ln ln 3 ln 10 ln MIN MAX MAX MAX 1A~8A 4hr 5 sec 0.5 sec 0.0 sec Environmental Temperature at 5 C Interrupting 35 amperes at 63V DC 60 amperes at 3V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max mm + Tape & Reel Quantity Environmental Specification 4000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C mm +

29 Temperature Rerating Curve Average Time Current Curves 1A 1.5A A.5A 3A 3.5A 4A 5A 6A 7A 8A Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Time in Seconds (s) Current in Amperes (A) Soldering Parameters CQ06LF 001 SERIES AMP Code Refer to Electrical

30 Type CQ06LT 1.6mmx 0.8mm (0603) Slow Blow Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 1A ~8A Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CQ06LT 001 H 1A CQ06LT 1.50 K 1.5A CQ06LT 00 N A CQ06LT.50 O.5A CQ06LT 003 P 3A CQ06LT 3.50 R 3.5A 63V CQ06LT 004 S 4A CQ06LT 005 T 5A CQ06LT 006 U 6A CQ06LT 007 V 7A CQ06LT 008 W 8A Approval UL Recognized 1A~8A Electrical Characteristic Tape and Reel Specification Item W P E F P D D1 Criterion Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Item P0 10P0 A0 B0 K0 T Criterion Tolerence ±0.10 ±0.0 ±0.10 ±0.10 ±0.10 ± ± 0. mm Reflow Solder Rated current 1 ln ln 3 ln 10 ln MIN MIN MAX MAX MAX 1A~8A 4hr 1 sec 10 sec 3 sec 0.05 sec Environmental Temperature at 5 C Interrupting 35 amperes at 63V DC 60 amperes at 3V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max mm + Tape & Reel Quantity Environmental Specification 4000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C mm +

31 Temperature Rerating Curve Average Time Current Curves CQ 06LT Series Clear Time Curves Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Soldering Parameters CQ06LT 001 SERIES AMP Code Refer to Electrical

32 Type CQ4PF 6.1mmx.6mm (410) Fast-Acting Fuse Series Feature a. Chip Fuse structure design with PCB body and copper & tin alloy element b. Use optical lithography & etching skill to make refinement element c. Complete on element with the terminal electrode plating Tin material to prevent element oxidation. d. Product meet 100% ROHS, lead free, HF & REACH requirement. e. Offer range of current ratings from 0.5A-1A & voltage up to 350VAC and 350VDC. Material Construction Body Material: FR4 Board Termination Material: Copper(Cu),Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CQ4PF A 500m A CQ4PF A 750mA CQ4PF 001 1A 1A CQ4PF A 1.5 A CQ4PF 00 A A CQ4PF.50.5A.5A CQ4PF A 3 A V CQ4PF 004 4A 4A CQ4PF 005 5A 5A CQ4PF 006 6A 6A CQ4PF 007 7A 7A CQ4PF 008 8A 8A CQ4PF A 10A CQ4PF 01 1A 1A Tape and Reel Specification Item W P E F P D D1 Criterion Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 L1 L W 1A~0A Reflow Solder Approval UL Recognized 0.5A~1A Electrical Characteristic Rated current 1 ln ln MIN MAX 0.5A~1A 4 hr 5 sec Environmental Temperature at 5 C Interrupting 100 amperes at 350V AC 100 amperes at 350V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Tape & Reel Quantity 500 pcs/reel Environmental Specification Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

33 Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) 0.5A 0.75A 1A 1.5A A.5A 3A 4A 5A 6A 7A 8A 10A 1A Current in Amperes (A) Soldering Parameters CQ4PF 001 SERIES AMP Code Refer to Electrical

34 Type CQ4PT 6.1mmx.6mm (410) High Inrush Fuse Series Feature a. Chip Fuse structure design with PCB body and copper & tin alloy element b. Use optical lithography & etching skill to make refinement element c. Complete on element with the terminal electrode plating Tin material to prevent element oxidation. d. Product meet 100% ROHS, lead free, HF & REACH requirement. e. Offer range of current ratings from 0.5A-1A & voltage up to 350VAC and 350VDC. Material Construction Body Material: FR4 Board Termination Material: Copper(Cu),Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CQ4PT A 500m A CQ4PT A 750mA CQ4PT 001 1A 1A CQ4PT A 1.5 A CQ4PT 00 A A CQ4PT.50.5A.5A CQ4PT A 3 A V CQ4PT 004 4A 4A CQ4PT 005 5A 5A CQ4PT 006 6A 6A CQ4PT 007 7A 7A CQ4PT 008 8A 8A CQ4PT A 10A CQ4PT 01 1A 1A Tape and Reel Specification Item W P E F P D D1 Criterion Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 L1 L W 0.5A~1A Reflow Solder Approval UL Recognized 0.5A~1A Electrical Characteristic Rated 1 ln ln.5 In 3 ln 8 In current MIN MIN MAX MAX MAX MAX 0.5A~1A 4 hr sec 60 sec 5 sec 3 sec 0.05 sec Environmental Temperature at 5 C Interrupting 100 amperes at 350V AC 100 amperes at 350V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Tape & Reel Quantity 500 pcs/reel Environmental Specification Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

35 Temperature Rerating Curve Average Time Current Curves Soldering Parameters CQ4PT 001 SERIES AMP Code Refer to Electrical

36 Type CQ1PF 3.1mmx 1.6mm (106) Fast-Acting Fuse Series Feature a. Chip Fuse structure design with PCB body and copper & tin alloy element b. Use optical lithography & etching skill to make refinement element c. Complete on element with the terminal electrode plating Tin material to prevent element oxidation. d. Product meet 100% ROHS, lead free, HF & REACH requirement. e. Offer range of current ratings from 0.5A-7A & voltage up to 63VDC and 63VAC. Material Construction Body Material: FR4 Board Termination Material: Copper(Cu),Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CQ1PF.500 F 500m A CQ1PF.750 G 750mA CQ1PF 001 H 1A CQ1PF 1.50 K 1.5 A CQ1PF 00 N A CQ1PF.50 O.5A 63V CQ1PF 003 P 3 A CQ1PF 004 S 4A CQ1PF 005 T 5A CQ1PF 006 U 6A CQ1PF 007 V 7A Approval Tape and Reel Specification Item A B W E F P0 P1 P D0 T 10PS Criterion Reflow Solder Max Min UL Recognized 0.5A~7A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.5A~7A 4 hr 5 sec 0. sec Environmental Temperature at 5 C Interrupting 100 amperes at 63V AC 100 amperes at 63V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max mm Tape & Reel Quantity Environmental Specification 4000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

37 Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) 0.5A 0.75A 1A 1.5A A.5A 3A 4A 5A 6A 7A Current in Ameres (A) Soldering Parameters CQ1PF 001 SERIES AMP Code Refer to Electrical

38 Type CQ1PT 3.1mmx 1.6mm (106) Slow Blow Fuse Series Feature a. Chip Fuse structure design with PCB body and copper & tin alloy element b. Use optical lithography & etching skill to make refinement element c. Complete on element with the terminal electrode plating Tin material to prevent element oxidation. d. Product meet 100% ROHS, lead free, HF & REACH requirement. e. Offer range of current ratings from 0.5A-7A & voltage up to 63VDC and 63VAC. Material Construction Body Material: FR4 Board Termination Material: Copper(Cu),Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CQ1PT.500 F 500m A CQ1PT.750 G 750mA CQ1PT 001 H 1A CQ1PT 1.50 K 1.5 A CQ1PT 00 N A CQ1PT.50 O.5A 63V CQ1PT 003 P 3 A CQ1PT 004 S 4A CQ1PT 005 T 5A CQ1PT 006 U 6A CQ1PT 007 V 7A Approval Tape and Reel Specification Item A B W E F P0 P1 P D0 T 10P Criterion Reflow Solder Max Min S UL Recognized 0.5A~7A Electrical Characteristic Rated current 1 ln ln 3 ln 8 ln MIN MIN MAX MAX MAX 0.5A~7A 4 hr sec 10 sec 3 sec 0.05 sec Environmental Temperature at 5 C Interrupting 100 amperes at 63V AC 100 amperes at 63V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max mm Tape & Reel Quantity Environmental Specification 4000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

39 Temperature Rerating Curve Average Time Current Curves Soldering Parameters CQ1PT 001 SERIES AMP Code Refer to Electrical

40 Type CQ06PF 1.55mmx 0.8mm (0603) Fast-Acting Fuse Series Feature a. Chip Fuse structure design with PCB body and copper & tin alloy element b. Use optical lithography & etching skill to make refinement element c. Complete on element with the terminal electrode plating Tin material to prevent element oxidation. d. Product meet 100% ROHS, lead free, HF & REACH requirement. e. Offer range of current ratings from 0.5A-5A & voltage up to 63VDC and 63VAC. Material Construction Body Material: FR4 Board Termination Material: Copper(Cu),Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CQ06PF.500 F 500m A CQ06PF.750 G 750mA CQ06PF 001 H 1A CQ06PF 1.50 K 1.5 A CQ06PF 00 N A 63V CQ06PF.50 O.5A CQ06PF 003 P 3 A CQ06PF 004 S 4A CQ06PF 005 T 5A Tape and Reel Specification Item A B W E F P0 P1 P D0 T 10P0 Criterion Reflow Solder Max Approval Min UL Recognized 0.5A~5A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.5A~5A 4hr 5 sec 0. sec Environmental Temperature at 5 C Interrupting 100 amperes at 63V AC 100 amperes at 63V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Tape & Reel Quantity Environmental Specification 5000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

41 Temperature Rerating Curve Average Time Current Curves Soldering Parameters CQ06PF 001 SERIES AMP Code Refer to Electrical

42 Type CQ06PT 1.55mmx 0.8mm (0603) Slow Blow Fuse Series Feature a. Chip Fuse structure design with PCB body and copper & tin alloy element b. Use optical lithography & etching skill to make refinement element c. Complete on element with the terminal electrode plating Tin material to prevent element oxidation. d. Product meet 100% ROHS, lead free, HF & REACH requirement. e. Offer range of current ratings from 0.5A-5A & voltage up to 63VDC and 63VAC. Material Construction Body Material: FR4 Board Termination Material: Copper(Cu),Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CQ06PT.500 F 500m A CQ06PT.750 G 750mA CQ06PT 001 H 1A CQ06PT 1.50 K 1.5 A CQ06PT 00 N A 63V CQ06PT.50 O.5A CQ06PT 003 P 3 A CQ06PT 004 S 4A CQ06PT 005 T 5A Tape and Reel Specification Item A B W E F P0 P1 P D0 T 10P0 Criterion Reflow Solder Max Approval Min UL Recognized 0.5A~5A Electrical Characteristic Rated current 1 ln ln 3 ln 8 ln MIN MIN MAX MAX MAX 0.5A~5A 4 hr sec 10 sec 3 sec 0.05 sec Environmental Temperature at 5 C Interrupting 100 amperes at 63V AC 100 amperes at 63V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Tape & Reel Quantity Environmental Specification 5000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

43 Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) 0.5A 0.75A 1A 1.5A A.5A 3A 4A 5A Current in Amperes (A) Soldering Parameters CQ06PT 001 SERIES AMP Code Refer to Electrical

44 Z Type CF1 3.1mmx1.55mm (106) High-surge Enhanced Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 3.1 Recommended Land Pattern.0-.4 Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics mm mm 0.60 ± 0.1 mm Reflow Solder Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CF1V6TR50 F 0.50A CF1V6TR80 K 0.80A CF1V6T1R0 L 1.00A CF1V6T1R5 M 1.5A 63V DC CF1V6T1R50 P 1.50A CF1V6TR0 S.00A CF1V3TR50 T.50A CF1V3T3R A V DC CF1V3T4R0 W 4.00A CF1V3T5R0 Y 5.00A CF1V3T7R0 7.00A Approval Tape and Reel Specification Item A B W F E P P P 1 0 D0 T Criterion 0.84 ±0.15 ±0. ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity 5000 pcs/reel UL Recognized 0.5A~7A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.5A~7A 4hr 60sec 1 sec Environmental Temperature at 5 C Interrupting 0.5A~A : 50 amperes at 63V DC.5A~7A : 50 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

45 Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CF 1 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

46 Type CF06 1.6mmx 0.80mm (0603) High-surge Enhanced Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 1.6 Recommended Land Pattern Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics mm mm 0.45 ± 0.1 mm Reflow Solder Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CF06V5TR40 E 0.40A 50V DC CF06V5TR50 F 0.50A CF06V3TR63 I 0.63A CF06V3TR80 K 0.80A CF06V3T1R0 L 1.00A CF06V3T1R5 M 1.5A CF06V3T1R50 P 1.50A CF06V3T1R60 N 1.60A CF06V3TR0 S.00A 3V DC CF06V3TR50 T.50A CF06V3T3R A CF06V3T3R15 U 3.15A CF06V3T4R0 W 4.00A CF06V3T5R0 Y 5.00A Tape and Reel Specification Item A B W F E P P P 1 0 D0 T Criterion ±0.1 ±0.1 ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity 5000 pcs/reel Approval UL Recognized 0.4A~5A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.4A~5A 4hr 60sec 1 sec Environmental Temperature at 5 C Interrupting 0.4A~0.5A : 50 amperes at 50V DC 0.63A~5A : 50 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

47 Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CF 04 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

48 Type CF04 1.0mmx 0.5mm (040) High-surge Enhanced Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 1.0 Recommended Land Pattern Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics mm 0.35 ± 0.05mm Reflow Solder Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CF04V3TR315 D 0.315A CF04V3TR50 F 0.50A CF04V3TR75 V 0.75A CF04V3TR80 K 0.80A CF04V3T1R0 L 1.00A CF04V3T1R5 M 1.5A CF04V3T1R50 P 1.50A 3V DC CF04V3T1R60 N 1.60A CF04V3TR0 S.00A CF04V3TR50 T.50A CF04V3T3R A CF04V3T3R15 U 3.15A CF04V3T4R0 W 4.00A Tape and Reel Specification Item A B W F E P P P 1 0 D0 T Criterion 0.45 ±0.05 ±0.05 ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity pcs/reel Approval UL Recognized 0.315A~4A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.315A~4A 4hr 60sec 1 sec Environmental Temperature at 5 C Interrupting 0.315A~4A : 35 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

49 Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CF 04 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

50 Z Type CFS1 3.1mmx 1.55mm (106) Fast Acting Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 3.1 Recommended Land Pattern.0-.4 Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics mm mm 0.60 ± 0.1 mm Reflow Solder Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CFS1V6TR50 F 0.50A CFS1V6TR80 K 0.80A CFS1V6T1R0 L 1.00A 63V DC CFS1V6T1R5 M 1.5A CFS1V6T1R50 P 1.50A CFS1V6TR0 S.00A CFS1V3TR50 T.50A CFS1V3T3R A CFS1V3T4R0 W 4.00A 3V DC CFS1V3T5R0 Y 5.00A CFS1V3T7R0 7.00A Approval Tape and Reel Specification Item A B W F E P P P 1 0 D0 T.0 Criterion ± ±0. ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity 5000 pcs/reel UL Recognized 0.5A~7A Electrical Characteristic Rated current 1 ln.5 ln 3 ln MIN MAX MAX 0.5A~7A 4hr 5sec 0. sec Environmental Temperature at 5 C Interrupting 0.5A~A : 50 amperes at 63V DC.5A~7A : 50 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

51 Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CFS 1 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

52 Type CFS06 1.6mmx 0.80mm (0603) Fast Acting Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 1.6 Recommended Land Pattern Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics mm mm 0.45 ± 0.1 mm Reflow Solder Ampere Voltage Nominal Nominal Catalog Marking Resistance Melting I t Number [ In ] ( V ) Cold Ohms A Sec CFS06V5TR40 E 0.40A V DC CFS06V5TR50 F 0.50A CFS06V3TR63 I 0.63A CFS06V3TR70 J 0.70A CFS06V3TR80 K 0.80A CFS06V3T1R0 L 1.00A CFS06V3T1R5 M 1.5A CFS06V3T1R50 P 1.50A CFS06V3T1R60 N 1.60A 3V DC CFS06V3TR0 S.00A CFS06V3TR50 T.50A CFS06V3T3R A CFS06V3T3R15 U 3.15A CFS06V3T4R0 W 4.00A CFS06V3T5R0 Y 5.00A CFS06V3T6R A Approval UL Recognized 0.4A~6A Electrical Characteristic Rated current 1 ln.5 ln 3 ln MIN MAX MAX 0.4A~6A 4hr 5sec 0. sec Environmental Temperature at 5 C Interrupting 0.4A~0.5A : 50 amperes at 50V DC 0.63A~6A : 50 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Tape and Reel Specification Item A B W F E P P P 1 0 D0 T Criterion ±0.1 ±0.1 ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion ±.0 ±1.0 ±1.0 ±1.0 ±.0 Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages Tape & Reel Quantity R<10% 5000 pcs/reel

53 Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CFS 1 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

54 Type CFS04 1.0mmx 0.5mm (040) Fast Acting Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 1.0 Recommended Land Pattern Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics mm 0.35 ± 0.05mm Reflow Solder Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CFS04V3TR50 F 0.50A CFS04V3TR80 K 0.80A CFS04V3T1R0 L 1.00A CFS04V3T1R5 M 1.5A CFS04V3T1R50 P 1.50A CFS04V3T1R60 N 1.60A CFS04V3TR0 S.00A 3V DC CFS04V3TR50 T.50A CFS04V3T3R A CFS04V3T3R15 U 3.15A CFS04V3T4R0 W 4.00A Approval Tape and Reel Specification Item A B W F E P P P 1 0 D0 T Criterion 0.45 ±0.05 ±0.05 ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity pcs/reel UL Recognized 0.5A~4A Electrical Characteristic Rated current 1 ln.5 ln 3 ln MIN MAX MAX 0.5A~4A 4hr 5sec 0. sec Environmental Temperature at 5 C Interrupting 0.5A~4A : 35 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

55 Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CFS 04 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

56 Z Type CP1 3.1mmx1.55mm (106) Fast Acting Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 3.1 Recommended Land Pattern.0-.4 Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics mm mm 0.60 ± 0.1 mm Reflow Solder Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CP1V6TR50 F 0.50A CP1V6TR80 K 0.80A CP1V6T1R0 L 1.00A CP1V6T1R5 M 1.5A 63V DC CP1V6T1R50 P 1.50A CP1V6TR0 S.00A CP1V3TR50 T.50A CP1V3T3R A V DC CP1V3T4R0 W 4.00A CP1V3T5R0 Y 5.00A CP1V3T7R0 7.00A Approval Tape and Reel Specification Item A B W F E P P P 1 0 D0 T Criterion 0.84 ±0.15 ±0. ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity 5000 pcs/reel UL Recognized 0.5A~7A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.5A~7A 4hr 60sec 1 sec Environmental Temperature at 5 C Interrupting 0.5A~A : 50 amperes at 63V DC.5A~7A : 50 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

57 r Temperature Rerating Curve Average Time Current Curves 0.5A 0.8 A 1A 1.5A 1.5A A.5A 3A 4A 5A 7A 10 1 Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CP 1 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

58 Type CP06 1.6mmx 0.80mm (0603) Fast Acting Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 1.6 Recommended Land Pattern Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics mm mm 0.45 ± 0.1 mm Reflow Solder Ampere Voltage Nominal Nominal Catalog Marking Resistance Melting I t Number [ In ] ( V ) Cold Ohms A Sec CP06V5TR50 F 0.50A 50V DC CP06V3TR63 I 0.63A CP06V3TR80 K 0.80A CP06V3T1R0 L 1.00A CP06V3T1R5 M 1.5A CP06V3T1R50 P 1.50A CP06V3T1R60 N 1.60A CP06V3TR0 S.00A 3V DC CP06V3TR50 T.50A CP06V3T3R A CP06V3T3R15 U 3.15A CP06V3T4R0 W 4.00A CP06V3T5R0 Y 5.00A Tape and Reel Specification Item A B W F E P P P 1 0 D0 T Criterion ±0.1 ±0.1 ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity 5000 pcs/reel Approval UL Recognized 0.5A~5A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.5A~5A 4hr 5sec 0. sec Environmental Temperature at 5 C Interrupting 0.5A :50 amperes at 50V DC 0.63A~5A : 50 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

59 Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CP 04 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

60 Type CP04 1.0mmx 0.5mm (040) Fast Acting Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 1.0 Recommended Land Pattern Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics mm 0.35 ± 0.05mm Reflow Solder Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CP04V3TR50 F 0.50A CP04V3TR80 K 0.80A CP04V3T1R0 L 1.00A CP04V3T1R5 M 1.5A CP04V3T1R50 P 1.50A CP04V3T1R60 N 1.60A 3V DC CP04V3TR0 S.00A CP04V3TR50 T.50A CP04V3T3R A CP04V3T3R15 U 3.15A CP04V3T4R0 W 4.00A Tape and Reel Specification Item A B W F E P P P 1 0 D0 T Criterion 0.45 ±0.05 ±0.05 ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity pcs/reel Approval UL Recognized 0.5A~4A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.5A~4A 4hr 5sec 0. sec Environmental Temperature at 5 C Interrupting 0.5A~4A : 35 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

61 Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CP 04 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

62 Z Type CPS1 3.1mmx 1.55mm (106) Time-Lag Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 3.1 Recommended Land Pattern.0-.4 Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics mm mm 0.60 ± 0.1 mm Reflow Solder Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec CPS1V6TR50 F 0.50A CPS1V6TR80 K 0.80A CPS1V6T1R0 L 1.00A 63V DC CPS1V6T1R5 M 1.5A CPS1V6T1R50 P 1.50A CPS1V6TR0 S.00A CPS1V3TR50 T.50A CPS1V3T3R A CPS1V3T4R0 W 4.00A 3V DC CPS1V3T5R0 Y 5.00A CPS1V3T7R0 7.00A Approval Tape and Reel Specification Item A B W F E P P P 1 0 D0 T.0 Criterion ± ±0. ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity 5000 pcs/reel UL Recognized 0.5A~7A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.5A~7A 4hr 10sec 0. sec Environmental Temperature at 5 C Interrupting 0.5A~A : 50 amperes at 63V DC.5A~7A : 50 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

63 Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CPS 1 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

64 Type CPS06 1.6mmx 0.80mm (0603) Time-Lag Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 1.6 Recommended Land Pattern Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics mm mm 0.45 ± 0.1 mm Reflow Solder Ampere Voltage Nominal Nominal Catalog Marking Resistance Melting I t Number [ In ] ( V ) Cold Ohms A Sec CPS06V5TR50 F 0.50A 50V DC CPS06V3TR63 I 0.63A CPS06V3TR80 K 0.80A CPS06V3T1R0 L 1.00A CPS06V3T1R5 M 1.5A CPS06V3T1R50 P 1.50A CPS06V3T1R60 N 1.60A 3V DC CPS06V3TR0 S.00A CPS06V3TR50 T.50A CPS06V3T3R A CPS06V3T3R15 U 3.15A CPS06V3T4R0 W 4.00A CPS06V3T5R0 Y 5.00A CPS06V3T6R A Tape and Reel Specification Item A B W F E P P P 1 0 D0 T Criterion ±0.1 ±0.1 ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity 5000 pcs/reel Approval UL Recognized 0.5A~6A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.5A~6A 4hr 10sec 0. sec Environmental Temperature at 5 C Interrupting 0.5A : 50 amperes at 50V DC 0.63A~6A : 50 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

65 Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CPS 1 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

66 PPTC SMD90 7.5mmx 5.5mm (90) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.90 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. d.operation Current: 0.30A~3.00A e.maximum Voltage: 6V~60V DC f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized 0.3A~3A TUV 0.3A~3A ANSI/J-std-00 Category 3 Tape & Reel Quantity 000 pcs/reel Electrical Characteristics(3 C) Part Number Hold Current Trip Current Rated Voltage Max Current Typical Max Time to Trip Resistance Power Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W A Sec Ohms Ohms SMD R SMD R SMD R SMD R SMD R SMD15-90-R SMD R SMD R SMD00-90-R SMD R SMD50-90-R SMD60-90-R SMD R SMD R I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin

67 Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD R SMD R SMD R SMD R SMD R SMD15-90-R SMD R SMD R SMD00-90-R SMD R SMD50-90-R SMD60-90-R SMD R SMD R Thermal Derating Curve Percent of Rated Hold and Trip Current 00% 150% 100% 50% Thermal Derating Curve, FSMD90 Series 0% A= SMD15-90-R ~ SMD R B= SMD R~ A B SMD R Ambient Temperature ( ) NOTE : Specification subject to change without notice.

68 Average Time Current Curves A = SMD R B = SMD R C = SMD R/ R D = SMD R E = SMD15-90-R F = SMD R G = SMD R H = SMD00-90-R/ R I = SMD50-90-R J = SMD60-90-R K= SMD R/ R Time-to-trip (S) A B C D EFGHIJK Fault Current (A) Soldering Parameters 3 6 A B C SMD R AMP Code Refer to Electrical Voltage

69 PPTC SMD mmx3.mm (181) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.181 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. d.operation Current: 0.10A~3.00A e.maximum Voltage: 6V~60V DC f.temperature Range: -45 C to +85 C Electrical Characteristics(3 C) Part Number Hold Current Trip Current Material Approval UL Recognized 0.A~3A Tape & Reel Quantity 000 pcs/reel SMD010-R SMD014-R SMD00-R SMD00-60-R SMD030-R SMD035-R SMD R SMD050-R SMD R SMD075-R SMD075-4R* SMD075-33R* SMD110-R SMD R SMD110-4R* SMD15-R SMD15-16R SMD150-R SMD150-1R SMD150-4R SMD160-R SMD160-1R SMD160-16R SMD00R SMD60R SMD60-13R* SMD60-16R* SMD300R* I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin Rated Voltage Max Current Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, ANSI/J-std-00 Category 3 TUV Typical 0.75A~3A Max Time to Trip Resistance * 1500 pcs/reel Power Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W Amp Sec Ohms Ohms

70 Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD010-R SMD014-R SMD00-R SMD00-60-R SMD030-R SMD035-R SMD R SMD050-R SMD R SMD075-R SMD075-4R SMD075-33R SMD110-R SMD R SMD110-4R SMD15-R SMD15-16R SMD150-R SMD150-1R SMD150-4R SMD160-R SMD160-1R SMD160-16R SMD00R SMD60R SMD60-13R SMD60-16R SMD300R NOTE : Specification subject to change without notice.

71 Thermal Derating Curve SMD Series Percent of Rated Hold and Trip Current 00% 150% 100% 50% 0% Ambient Temperature ( ) A= SMD 075-R, 075-4R, R, 110-R, R, 110-4R, 15-R, 15-16R, 150-R, 150-1R, 150-4R, 160-R, 160-1R, R, 00R, 60R, 60-13R, 60-16R,300R B= SMD010-R, 014-R, 00-R, R, 030-R, 035-R, R,050-R, R Average Time Current Curves A = SMD010-R B = SMD014-R C = SMD00-R / R D = SMD030-R E = SMD035-R / R F = SMD050-R / R G = SMD075-R / 075-4R / R H = SMD110-R / R / 110-4R I = SMD15-R / 15-16R J = SMD150-R / 150-1R / 150-4R K = SMD160-R / 160-1R / R L = SMD00R M = SMD60R / 60-13R / 60-16R N = SMD300R Time-to-trip (S) SMD S eries A B C D E F G HIJ K LM N Fault Current (A) NOTE : Specification subject to change without notice.

72 Soldering Parameters 3 6 A B C SMD R AMP Code Refer to Electrical Voltage

73 PPTC SMD110 3.mmx.5mm (110) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.110 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. Lower resistance than standard SMD devices. d.operation Current: 0.05A~.00A e.maximum Voltage: 6V~60V DC f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized 0.05A~A TUV 0.05A~A Tape & Reel Quantity ANSI/J-std-00 Category pcs/reel * 4000 pcs/reel Electrical Characteristics(3 C) Part Number Hold Current I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin Trip Current Rated Voltage Max Current Typical Max Time to Trip Resistance Power Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W A Sec Ohms Ohms SMD R SMD R SMD R SMD R* * SMD R * SMD R * SMD R SMD R SMD R SMD R SMD00-110R

74 Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD00-110R Thermal Derating Curve 00% Thermal Derating Curve, SMD110 Series Percent of Rated Hold and Trip Current 150% 100% 50% 0% Ambient Temperature ( ) NOTE : Specification subject to change without notice.

75 Average Time Current Curves A = SMD R B = SMD R C = SMD R D = SMD R E = SMD R F = SMD R/ R G = SMD R H = SMD R I = SMD R J = SMD00-110R Time-to-trip (S) A B C D E F G H I J Fault Current (A) Soldering Parameters 3 6 A B C SMD R AMP Code Refer to Electrical Voltage

76 PPTC SMD106 3.mmx 1.6mm (106) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.106 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. Lower resistance than standard SMD devices. d.operation Current: 0.05A~.00A e.maximum Voltage: 6V~60V DC f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized TUV 0.05A~A 0.05A~A Tape & Reel Quantity ANSI/J-std-00 Category pcs/reel * 4000 pcs/reel * * 000 pcs/reel Electrical Characteristics(3 C) Part Number Hold Current I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin Trip Current Rated Voltage Max Current Typical Max Time to Trip Resistance Power Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W A Sec Ohms Ohms SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R * SMD R * SMD R * SMD R * SMD R SMD R SMD R SMD R SMD R * * SMD00-106R * *

77 Dimensions Part Thermal Derating Curve A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD00-106R % SMD106 Series Percent of Rated Hold and Trip Current 150% 100% 50% 0% Ambient Temperature ( )

78 Average Time Current Curves Z= SMD R A= SMD R B= SMD R C= SMD R D= SMD R E= SMD R / R F= SMD R / R G= SMD R / R H= SMD R / R I= SMD R J= SMD R K= SMD R L= SMD00-106R Time-to-trip (S) Z A B C D E F G H I J K L SMD106 Series Fault current (A) Soldering Parameters 3 6 A B C SMD R AMP Code Refer to Electrical Voltage

79 PPTC SMD0805.0mmx 1.mm (0805) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.0805 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. Lower resistance than standard SMD devices. d.operation Current: 0.10A~1.00A e.maximum Voltage: 6V~15V f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized 0.10A~1A TUV 0.10A~1A Tape & Reel Quantity ANSI/J-std-00 Category pcs/reel * 4000 pcs/reel Electrical Characteristics(3 C) Part Number Hold Current I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin Trip Current Rated Voltage Max Current Typical Max Time to Trip Resistance Power Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W Amp Sec Ohms Ohms SMD R * SMD R * SMD R * SMD R SMD R SMD R SMD R

80 Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD R SMD R SMD R SMD R SMD R SMD R SMD R Thermal Derating Curve SMD0805 Series 00% Percent of Rated Hold and Trip Current 150% 100% 50% 0% Ambient Temperature ( ) NOTE : Specification subject to change without notice.

81 Average Time Current Curves 100 A B C D E F A = SMD R B = SMD R C = SMD R D = SMD R / SMD R E = SMD R F = SMD R Time-to-trip (S) Fault current (A) Soldering Parameters 3 6 A B C SMD R AMP Code Refer to Electrical Voltage

82 PPTC SMD mmx 0.8mm (0603) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.0603 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. Lower resistance than standard SMD devices. d.operation Current: 0.01A~0.0A e.maximum Voltage: 9V~60V DC f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized 0.05A~0.0A TUV 0.05A~0.0A Tape & Reel Quantity ANSI/J-std-00 Category pcs/reel Electrical Characteristics(3 C) Part Number Hold Current I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin Trip Current Rated Voltage Max Current Typical Power Max Time to Trip Resistance Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W A Sec Ohms Ohms SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R

83 Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R Thermal Derating Curve 00% SMD0603 Series Percent of Rated Hold and Trip Current 150% 100% 50% 0% Ambient Temperature ( ) NOTE : Specification subject to change without notice.

84 Average Time Current Curves A= SMD R 100 A BCD E F GH I SMD0603 Series B= SMD R C= SMD R 10 D= SMD R E= SMD R F= SMD R G= SMD R H= SMD R I= SMD R Time-to-Trip (s) Fault Current (A) Soldering Parameters 3 6 A B C SMD R AMP Code Refer to Electrical

85 PPTC LO RHO SMD mmx 3.mm (181) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.181 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. Lower resistance than standard SMD devices. d.operation Current: 1.4A~3.7A e.maximum Voltage: 6V f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized 1.4A~3.7A TUV 1.4A~3.7A Tape & Reel Quantity ANSI/J-std-00 Category pcs/tape Electrical Characteristics(3 C) Part Number Hold Current I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin Trip Current Rated Voltage Max Current Typical Max Time to Trip Resistance Power Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W A Sec Ohms Ohms SMD140RZ SMD190RZ SMD70RZ SMD300RZ SMD370RZ

86 Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD140RZ SMD190RZ SMD70RZ SMD300RZ SMD370RZ Thermal Derating Curve Lo Rho SMD181 Series 00% Percent of Rated Hold and Trip Current 150% 100% 50% 0% Ambient Temperature ( ) NOTE : Specification subject to change without notice.

87 Average Time Current Curves 100 Lo Rho SMD 181 Series A B CDE A = SMD140RZ B = SMD190RZ C = SMD70RZ D = SMD300RZ E = SMD370RZ Time-to-trip (S) Fault Current (A) Soldering Parameters 3 6 A B C AMP Code Refer to Electrical SMD 100 RZ

88 PPTC LO RHO SMD110 3.mmx.5mm (110) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.110 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. Lower resistance than standard SMD devices. d.operation Current: 1.75A~3.80A e.maximum Voltage: 6V f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized 1.75A~.00A TUV 1.75A~.00A Tape & Reel Quantity ANSI/J-std-00 Category pcs/tape * 4000 pcs/tape Electrical Characteristics(3 C) Part Number Hold Current I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin Trip Current Rated Voltage Max Current Typical Power Max Time to Trip Resistance Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W A Sec Ohms Ohms SMD RZ * SMD00-110RZ * SMD RZ SMD RZ SMD RZ

89 Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD RZ SMD RZ SMD RZ SMD RZ SMD RZ Thermal Derating Curve 00% Lo Rho SMD110 series Percent of Rated Hold and Trip Current 150% 100% 50% 0% Ambient Temperature ( ) NOTE : Specification subject to change without notice.

90 Average Time Current Curves Lo Rho SMD 110 series 100 A B C D E A= SMD RZ B= SMD00-110RZ C= SMD RZ D= SMD RZ E= SMD RZ Time-to-trip (S) Fault Current (A) Soldering Parameters 3 6 A B C AMP Code Refer to Electrical SMD RZ

91 PPTC LO RHO SMD106 3.mmx 1.6mm (106) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.106 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. Lower resistance than standard SMD devices. d.operation Current: 0.5A~.0A e.maximum Voltage: 6V f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized 0.5A~.0A TUV 0.5A~.0A Tape & Reel Quantity ANSI/J-std-00 Category pcs/tape Electrical Characteristics(3 C) Part Number Hold Current Trip Current Rated Voltage Max Current Typical Max Time to Trip Resistance Power Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W A Sec Ohms Ohms SMD RZ SMD RZ SMD RZ SMD RZ SMD00-106RZ I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin

92 Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD RZ SMD RZ SMD RZ SMD RZ SMD00-106RZ Thermal Derating Curve 00% Lo Rho SMD106 series Percent of Rated Hold and Trip Current 150% 100% 50% 0% Ambient Temperature ( 0 C) NOTE : Specification subject to change without notice.

93 Average Time Current Curves A= SMD RZ B= SMD RZ C= SMD RZ D= SMD RZ E= SMD00-106RZ Time-to-trip (S) A B C D E Lo Rho SMD 106 series Fault Current (A) Soldering Parameters 3 6 A B C AMP Code Refer to Electrical SMD RZ

94 PPTC LO RHO SMD0805.0mmx 1.mm (0805) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.0805 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. Lower resistance than standard SMD devices. d.operation Current: 0.75A~1.75A e.maximum Voltage: 6V f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized 0.75A~1.5A TUV 0.75A~1.5A Tape & Reel Quantity ANSI/J-std-00 Category pcs/tape Electrical Characteristics(3 C) Part Number Hold Current Trip Current Rated Voltage Max Current Typical Power Max Time to Trip Resistance Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W A Sec Ohms Ohms SMD RZ SMD RZ SMD RZ SMD RZ SMD RZ I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin

95 Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD RZ SMD RZ SMD RZ SMD RZ SMD RZ Thermal Derating Curve 00% Lo Rho SMD0805 series Percent of Rated Hold and Trip Current 150% 100% 50% 0% Ambient Temperature ( 0 C) NOTE : Specification subject to change without notice.

96 Average Time Current Curves A = B = C = D = E = SMD RZ SMD RZ SMD RZ SMD RZ SMD RZ Time-to-trip (S) A B C D E Lo Rho SMD 0805 series Fault Current (A) Soldering Parameters 3 6 A B C AMP Code Refer to Electrical SMD RZ

97 PPTC LO RHO SMD mmx 0.8mm (0603) Surface Mountable PTC Resettable Fuse Feature a.rohs compliant & Halogen Free b.all high-density boards c.0603 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. Lower resistance than standard SMD devices. d.operation Current: 0.5A~0.75A e.maximum Voltage: 6~9V f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized pending TUV pending Tape & Reel Quantity ANSI/J-std-00 Category pcs/tape Electrical Characteristics(3 C) Part Number Hold Current Trip Current Rated Voltage Max Current Typical Max Time to Trip Resistance Power Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W A Sec Ohms Ohms SMD RZ SMD RZ SMD RZ SMD RZ I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin

98 Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD RZ SMD RZ SMD RZ SMD RZ Thermal Derating Curve 00% Thermal Derating Curve, Lo Rho FSMD0603 series Percent of Rated Hold and Trip Current 150% 100% 50% 0% Ambient Temperature ( ) NOTE : Specification subject to change without notice.

99 Average Time Current Curves 100 A B C D A = SMD RZ B = SMD RZ C = SMD RZ 10 D = SMD RZ Time-to-trip (S) Fault Current (A) Soldering Parameters 3 6 A B C AMP Code Refer to Electrical SMD RZ