1 Features/ 特征 : Emitting Color/ 发光颜色 :/Green// 红色 / 绿色 / 蓝色 Lens Type/ 封装特性 :Water clear/ 透明 Device Outline/ 外形特征 :5.5 5. 1.95 (unit:mm) RoHS compliant/ 符合 RoHS 标准 2 Applications/ 应用 : Backlight for Mobile,Machine Vision, LCD Display/ 手机 电话 显示屏背光源 Backlight in Dashboard and switch of Automive/ 汽车仪表盘 记程器背光源 3 Outline Dimensions/ 产品外形尺寸 (units:mm) : C.8 deep.5 1 2 6 5 3 4 灌胶点 B 1 6 R 2 5 G 3 4 1/1
4 Absolute maximum ratings/ 极限参数 (Ta = 25 ): Parameter 参数 Color 颜色 Symbol 符号 Test Condition 测试条件 Values 数值 Min. Max. Unit 单位 Power Dissipation 损耗功率 Reverse Voltage 反向电压 Pulse Current 正向峰值电流 Forward Current 正向工作电流 Operating Temperature 工作温度范围 Storage Temperature 储存温度范围 6 Green Pd 85 mw 85 Green VR IR = 3μA 5 V Green IFp Duty=.1,1kHz 1 ma Green IFm 25 ma Green Topr -4 +85 Green Tstr -4 +85 2/1
5 Electrical and optical characteristics/ 光电参数 (Ta = 25 ): Parameter 参数 Color 颜色 Symbol 符号 Test Condition 测试条件 Values 数值 Min Typ Max Unit 单位 Forward Voltage 正向电压 Reverse Current 反向电流 Dominate Wavelength 主波长 Peak Wavelength 峰值波长 Spectral Line half-width 半波长宽度 Luminous Intensity 发光强度 Viewing Angle 发光指向角 2.1 2.5 Green VF IF = 2mA 2.9 3.4 V 3. 3.4 3 Green 3 IR VR =5V 3 619 63 Green λd IF = 2mA 52 53 465 475 631 Green λp IF = 2mA 527 468 2 Green Δλ IF = 2mA 3 3 39 59 Green IV IF = 2mA 77 112 2 28 μa nm nm nm mcd Green 2θ1/2 IF = 2mA 12 Deg. 3/1
6 Typical electrical/optical characteristic curves/ 光电特性曲线 : 5 Fig.1 正向电流 Vs. 正向电压 Fig.2 相对亮度 Vs. 正向电流 2.5 Forward Current(mA) 4 3 2 1 1.2 1.6 R B G Luminous Intensity Relative Value at IF=2mA 2. 2.4 2.8 3.2 3.6 1 2 3 4 5 Forward Voltage(V) IF-Forward Current (ma) 2. 1.5 1..5 R/G/B Fig.3 正向电流 Vs. 环境温度 Fig.4 相对亮度 Vs. 环境温度 Forward Current(mA) 5 4 3 2 1 2 4 R/G/B 6 8 1 Relative Luminous Intensity 2.5 2. 1.5 1..5-4 -2 2 R/G/B 4 6 8 9 Ambient Temperature TA ( ) Ambient Temperature TA ( ) Relative Luminous Intensity / 相对亮度 1 75 5 25 Fig.5 相对亮度 Vs. 波长 B G R 4 45 5 55 6 Wavelength λ(nm)/ 波长 65 1..9.8.7 SPATIAL DISTRIBUTION.5.3.1.2.4.6 4/1
7 Relibility Analysis/ 可靠性试验 7.1 Test Items And Results/ 测试项目和判据 No. Item/ 项目 Test Condition/ 测试条件 Spec. / 引用标准 Q ty/ 数量 Time/ 时间 Standard/ 判定 1 IR Reflow (Reflow Soldering) / 回流焊接 Tsld=26,1sec GB/T 4937, Ⅱ,2.2 5 2times ALL PASS 2 Solder ability/ 可焊性 Tsld=235±5,3sec 5 1times Over 95% ALL PASS 3-4 11 Temperature Cycle/ GB/T 4937, 3min ~ 3min 高低温循环 Ⅲ,1 The cut is not more than 1 min 5 3cycles ALL PASS 4 Moisture Resistance 85 GB/T 4937, C/85%RH Cyclic / 湿热循环 Ⅲ,4 5 168hrs ALL PASS 5 High Temperature Storage / 高温储存 Ta=1 GB/T 4937, Ⅲ,2 5 1hrs ALL PASS 6 Low Temperature Storage / 低温储存 Ta=-4 GB/T 4937, Ⅲ,2 5 1hrs ALL PASS 7 Steady State perating Life / 电耐久性 IF=2mA Ta=25 GB/T 1894.3 Part A 5 1hrs Iv decay <3% 7.2 Criteria For Judging Damage/ 判断标准 Item/ 项目 Symbol/ 符号 Test conditions / 测试条件 Criteria for Judgement / 判断标准 Min./ 最小值 Max./ 最大值 Luminous Intensity/ 亮度 Iv IF=2mA Iv*.7 / Forward Voltage/ 正向电压 VF IF=2mA / U.S.L*1.1 Reverse current/ 反向电流 IR VR=5v / U.S.L*2 *U.S.L.:Upper Standard Level / 上限 *L.S.L.:Lower Standard Level / 下限 5/1
8 Specification of Packing / 包装规格 8.1 Taping and Orientation/ 编带和方向 Quantity/ 数量 :1 units/reel Diameter/ 直径 :178 mm 6/1
8.2 Specification of Packing/ 包装规格 Diameter/ 直径 : 178 mm Width/ 宽度 : 17 mm =>1 pcs / Reel (Anti-Static Shielding/ 抗静电保护袋 ) Thickness/ 厚度 : T=.1 mm => 1 Reel / Bag 4 Bags / Box =>4, pcs / Box 195mm 85mm 195mm 7/1
9 Notes/ 注意 9.1 Moisture Proof Packaging/ 防潮包装 9.1.1 LEDs need to package in moisture proof bag. When moisture is absorbed into the SMT package it may vaporize and expand during soldering. There is a possibility that this can cause exfoliation of the contacts and damage to the optical characteristics of the LEDs. For this reason, the moisture proof bag is used to keep moisture to a minimum in the bag. 产品必须包封装在防潮包装袋中 当湿气进入防潮包装袋的时候, 在焊接时, 湿气会受热汽化膨胀, 从而可能影响产品的光学特性, 甚至造成封装胶体的开裂剥离 因此, 防潮袋要求放置在保持低湿度的盒中 9.1.2 Moisture proof function is inactive. The moisture proof bag is made of an aluminum moisture proof bag. A package of a moisture absorbent material (silica gel) is inserted into the aluminum moisture proof bag. The silica gel turns the smashing from the transparent circular spherical pellet. 防潮的作用是缓慢的 防潮袋使用铝防潮袋, 并在铝防潮袋中放入潮气吸收材料 ( 硅胶干燥剂 ) 当硅胶干燥剂吸收潮气后, 硅胶干燥剂从透明圆形球状颗粒变成粉碎物 9.2 Storage Method/ 储存方式 9.2.1 Before opening the bag: The LEDs should be used within a year and kept at 3 or less and 7%RH or less. The moisture proof bag with absorbent material is needed when storing the LEDs. 拆开包装袋之前 : 产品可以使用一年, 但要求放置在温度低于 3, 湿度低于 7% 的环境中 ; 当存放产品时, 必须放置在带有干燥剂的防潮容器中 9.2.2 After opening the bag: The LEDs should be soldered within 72 hours after opening the package. If unused LEDs remain, they should be stored in moisture proof bags with moisture absorbent material. If the LEDs have exceeded the storage time or the moisture absorbent material has faded away. Baking process should be performed by using more than 24hours baking at 6±5 before using LEDs. It recommended that the user use the LEDs as soon as possible. 拆开包装袋之后 : 产品应该在拆封后的 72 小时内焊接完毕 ; 如果没用完, 产品应该储 8/1
存在带有干燥剂的防潮包装袋中 ; 如果产品超出了使用期限或者干燥剂失效, 那么产品在使用前必须在 6±5 中烘烤至少 24 小时 ; 建议客户尽快的使用完产品 9.3 Heat Generation/ 产品热量的产生 Thermal design of the end applications are of paramount importance. Please consider the heat generation of the LED when making the system design. It is necessary to avoid intense heat generation and operate within the maximum ratings given in this specification. 应用产品的热学设计是至关重要的 在做系统设计时, 请考虑 LED 的散热, 避免热量的积累, 必须严格的在允许的温度范围内使用 9.4 Soldering/ 焊接 9.4.1 Lead Solder/ 回流焊接 9.4.3 Hand Soldering(Not Recommended)/ 手工焊接 ( 不推荐 ) 9/1
Soldering iron/ 烙铁焊接 :3 degrees C max/ 不超过 3 ;5 seconds max/ 不超过 5s; once/ 允许 1 次. 9.5 Cleaning/ 清洗 It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. It should be confirmed beforehand whether the solvents will dissolve the package the resin or not when using other solvents. Please do not clean the LEDs by the ultrasonic. If it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on ultrasonic power and the assembled condition. Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur. 建议使用酒精作为溶剂清洗 LEDs 若要使用其他溶剂, 应该预先证实是否能溶化封装料 请不要使用超声波清洗 LEDS, 如果一定要使用超声波清洗, 则一定要注意超声波的功率和超声条件 在清洗作业前, 必须预先实验确认对 LEDS 无任何的伤害 9.6 Static Electricity/ 静电 It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. All devices, equipment and machinery must be properly grounded. It is recommended that precautions be taken against surge voltage to the equipment that mounts the LEDs. 在接触 LEDs 时, 建议使用防静电手腕带或防静电手套 所有的器件 设备和机器必须 有可靠的接地 对所有 LEDs 接触的设备, 建议采取预防措施消除冲击电压 9.7 Others/ 其他 The LED light output is strong enough to injure human eyes. Precautions must be taken to prevent looking directly at the LEDs with unaided eyes for more than a few seconds. LED 的光辐射足够强时, 会对人眼造成伤害 若眼睛要直接看 LED, 并且要一定的时 间, 则必须采取相应防护措施 1/1