Overview 简介 The LSWMXGTPM interface card provides two /0GBase-T Ethernet ports. The LSWMXGT8PM interface card provides eight /0GBase-T Ethernet ports. LSWMXGTPM 和 LSWMXGT8PM 接口模块扩展卡对外分别提供 个和 8 个 /0 GBase-T 自适应以太网端口 /0GBase-T autosensing Ethernet port /0GBase-T 自适应以太网端口 /0GBase-T autosensing Ethernet port LED /0GBase- T 自适应以太网端口状态指示灯 Captive screw 松不脱螺钉 Ejector lever 扳手 /0GBase-T autosensing Ethernet port /0GBase-T 自适应以太网端口 Handle 拉手 Captive screw 松不脱螺钉 /0GBase-T autosensing Ethernet port LED /0GBase-T 自适应以太网端口状态指示灯 The switch models that the LSWMXGTPM and LSWMXGT8PM interface cards are applicable to might change over time. For the most up-to-date list of applicable switch models, contact HC Support or marketing staff. LSWMXGTPM 和 LSWMXGT8PM 接口模块扩展卡适用于 HC 多款交换机产品, 其适用机型的准确信息随着时间变化有更新的可能性, 若您需要更详细的适配信息, 请咨询 HC 公司市场人员或技术支持人员

Installing an LSWMXGTPM interface card 安装 LSWMXGTPM 接口模块扩展卡 Unpack the card. Insert the card slowly into the slot along the guide rails. 从包装袋中取出接口模块扩展卡, 并将接口模块扩展卡沿着插槽导轨水平缓慢地推进接口模块扩展卡插槽 Rotate inward the ejector lever until the card is in close contact with the switch. 将扳手用力向内扣合, 确保接口模块扩展卡和交换机紧密接触 Use the Phillips screwdriver to tighten the captive screw on the card. 使用十字螺丝刀顺时针方向旋转, 拧紧接口模块扩展卡上的松不脱螺钉 Installing an LSWMXGT8PM interface card 安装 LSWMXGT8PM 接口模块扩展卡 Unpack the card. Insert the card slowly into the slot along the guide rails. 从包装袋中取出接口模块扩展卡, 并将接口模块扩展卡沿着插槽导轨水平缓慢地推进接口模块扩展卡插槽 Use the Phillips screwdriver to tighten the captive screw on the card. 使用十字螺丝刀顺时针方向旋转, 拧紧接口模块扩展卡上的松不脱螺钉 4 Removing an LSWMXGTPM interface card 拆卸 LSWMXGTPM 接口模块扩展卡

Use a Phillips screwdriver to loosen the captive screw on the card. 使用十字螺丝刀逆时针方向旋转, 松开接口模块扩展卡上的松不脱螺钉 Hold the ejector lever to pull the card outward until the card is disconnected from the connectors. 拉动扳手使接口模块扩展卡与设备内连接器端子脱离 Hold the card with both hands and take it out slowly. 用双手水平缓慢地取出接口模块扩卡 5 Removing an LSWMXGT8PM interface card 拆卸 LSWMXGT8PM 接口模块扩展卡 Use a Phillips screwdriver to loosen the captive screw on the card. 使用十字螺丝刀逆时针方向旋转, 松开接口模块扩展卡上的松不脱螺钉 Grasping the handle of the interface card, pull out the interface card slowly out the interface card slot. 向外拉动拉手, 水平缓慢地取出接口模块扩展卡 Verifying the installation 安装完成后的检查 After the installation is complete, determine whether the card is operating correctly. If the card fails to operate correctly, perform the following steps: Reinstall the card following the installation procedures described in this document. If the problem persists, contact HC Support. 全部安装完成后, 在交换机运行正常的情况下, 若发现接口模块扩展卡无法正常工作 : 您可以按照手册中介绍的方法重新安装接口模块扩展卡 如果重新安装后, 接口模块扩展卡仍无法正常工作, 请您联系 HC 技术支持人员 Ports 接口 Item 属性 Specification 描述 /0GBase-T autosensing Ethernet ports /0GBase-T 自适应以太网端口 Connector 连接器类型 Port mode 端口属性 RJ-45 0 Gbps, full duplex. 0Gbps 全双工 Gbps, full duplex. Gbps 全双工 MDI/MDI-X autosensing. MDI/MDI-X 自适应 4

Item 属性 Maximum transmission distance 最大传输距离 Cable 使用电缆规格 Standard 符合标准 Specification 描述 Category 6 unshielded twisted pair cable (6 类非屏蔽双绞线 ): 55 m (80.45 ft) Category 6 shielded twisted pair cable (6 类屏蔽双绞线 ): 00 m (8.08 ft) Category 6A or above twisted pair cable (6A 类及以上双绞线 ): 00 m (8.08 ft) Category 6 or above twisted pair cables 6 类及 6 类以上双绞线 IEEE 80.an IEEE 80.ab LED Status 指示灯状态 Description 指示灯含义 /0GBase-T autosensing Ethernet port LED /0GBase-T 自适应以太网端口指示灯 Steady green 绿色常亮 Flashing green 绿色闪烁 Steady yellow 黄色常亮 Flashing yellow 黄色闪烁 Off 灯灭 The port is operating at 0 Gbps, and a link is present on the port. 端口工作在 0G 模式下, 并且端口 Link Up The port is sending or receiving data at 0 Gbps. 端口工作在 0G 模式下, 正在接收或发送数据 The port is operating at Gbps, and a link is present on the port. 端口工作在 G 模式下, 并且端口 Link Up The port is sending or receiving data at Gbps. 端口工作在 G 模式下, 正在接收或发送数据 No link is present on the port. 端口没有 Link Up 5