PMZ.SMS.026_622II说明书C_V1.0.cdr

Transcription

1 YN622C II RX OFF User Manual 用户手册

2 注意事项 Contents General Description Function Introduction Supported Functions List Compatibility List Name of Parts Preparation Before Use Setting Flash Awaking /Testing Flash Remote Control Mode Mix Control Mode Flash Triggering of Type B/C Camera PC Port Triggering References Troubleshooting Specifications Cautions Please turn off power supplies of all equipment when connecting or installing the product. Please keep it dry. Be sure not to use wet hand to touch the product. It is also not allowed to immerse the product into waster or make it be exposed in the rain; otherwise it may not work normally or even be damaged. Do not use it in explosive situations; violation of this warning may cause an explosion or fire. This product involves battery, please be in strict accordance with the relevant provisions on the use of the battery, otherwise it would cause property damage or personal injury. vread this user manual while also referring to your camera's & flash's user manual before using in order to correct use this product.

3 RX OFF General Description This product is a wireless transceiver, transmitting & receiving mode will automatically switched. to express conveniently, in this user manual, it is called transmitter (master control unit) when being installed on the hot shoe of the camera, while it is called receiver (slave unit) when a flash is installed or connected. On-Top Flash Off-Camera Flash Flash Control Menu (Camera Menu) YN622C II Off-Camera Flash LCD Display YN622C-TX Recommended optional YN622C-TX E-TTL wireless flash controller as a transmitter, about the introduction of this product, please visit the following website : 1

4 Function Introduction Thank you for purchase the products of Yongnuo firstly. The new upgrade version YN622C II can set to "622" or "560-RX" communication mode through the power switch, supports receiving the trigger signal of the YN560-TX/RF605(603 mode)/rf603(ii) series products, with multi aspects improved, equipped with quick lock design and supports USB firmware upgrade. YN622C II E-TTL wireless flash trigger is a high performance master and slave equipment of multiple flashes photography, through digital FSK 2.4GHz radio wireless transmission, and different photographic effects can be realized through setting your flash at 360 degrees. It design of transceiver, the distance of remote control reaches 100M, supporting 7 wireless channels and A/B/C three groups. Remotely change the modes and parameters of the flash quickly when using the Canon EOS series DSLR cameras which supports external flash function, such as TTL ratio or manually set each group of flash output. Support high-speed sync, the max sync speed is 1/8000s*, Support E-TTL, Manual and Multi flash modes. Support E-TTL flash installing on the top of transmitter. Compatible cameras/flashes is needed when using TTL function The highest sync speed of some camera types is 1/4000s, some of flash or camera models may reach to 1/250s only or less if it doesn't support high sync speed. 2

5 Supported Functions List Quick lock design Supports USB firmware upgrade S u p p o r t s " " c o m m u n i c a t i o n m o d e, " R X " communication mode Compatible flash mode: E-TTL (II)/ Manual/ Multi Compatible Shutter sync: 1st curtain, 2nd curtain, high speed sync (HSS/FP), Max 1/8000s sync speed Control remote flash using camera's flash control menu screen(remote Control Mode) Support E-TTL / Manual/ Multi flash mode mix using(mix Control Mode) Flash on hot-shoe of transmitter supports ETTL Support Flash Exposure Compensation (FEC) Support Flash Exposure Bracketing (FEB) Support Flash Exposure Lock (FEL) Support modeling Flash Support E-TTL group ratio (ALL/ A:B/ A:B C) Support Manual/Multi group (ALL/ A:B/ A:B:C) Support flash zooming (auto, manual) Support AF assist beam emitter(af Lamp) Support PC port triggering strobe flashes and support 1st, 2nd curtain/hss (Super Sync) Support LCD Live view triggering Support high-speed continuous shooting trigger Settings saved automatically Compatible with ALL YongNuo/ Canon EXII series flashes Support single-contact of camera & flash triggering (max sync speed is 1/250s) 3

6 Compatibility List Functions supported by the product depend on the camera and flash used. According to different types of cameras, in this user manual, the EOS DSLR camera with external flash(speedlite) control menu is called type A camera; while EOS DSLR camera without external flash control menu is called type B camera; other camera brands with standard hot-shoe is called type C camera. List of Type A cameras: Canon EOS 1DX/EOS 5D Mark II/ 5DMark III/1Ds Mark III/1D Mark IV/1D Mark III/ 6D/7D/7DII/60D/70D/50D/40D/450D/ 500D Series/600D Series/700D Series/1000D Series List of Type B cameras: Canon EOS 5D/10D/20D/30D/ 300D/350D/400D/1D/1D Mark II Compatible ETTL flash list: (support wireless remote control through camera menu) Canon 600EX(RT)/580EXII/430EXII/320EX/270EX(II) YongNuo YN600EX-RT /YN568EX(II)/YN565(II)/ YN468(II)/YN467(II)/YN EX/550EX/580EX or other parts of the flash is not supported remote control via the camera menu, need to manually set the flash modes(parameters). When using general type manual flash or strobe flash connect to PC port, flash output needs to be set manually. In this user manual, assumes that you are using the type A camera and compatible ETTL flash, as for type B/ C camera, please refer to page 22. 4

7 Name of Parts Indicator Blinking Keep Lighting Channel Indicator Group Indicator Communicating (Remote control mode) Firing group or receiving group The protective film can be torn out. Mix Control Mode Testing Communicating State Indicator(green) TX Communicating(622) Testing Communicating State Indicator(red) RX Communicating(622) State Indicator(orange) RX Communicating(560-RX) Standby State Standby State Q R RX OFF A B C D E F G H I AF assist beam emitter(p.24) Channel setting button (p.8/9) Test button(p.9/10) PC port(p.23) Channel indicator (p.8) Group indicator (p.8/9) Hot shoe(p.6/7) Group setting button(p.8/9) Power switch(p.8) J K L M N O P Q R K State indicator(p.5) Dust and water resistant adapter Mounting foot lock lever(p.6/7) Lock-release button USB upgrade terminal(p.26) Mounting foot(p.6/7) locking pin(p.6) Battery compartment(p.6) Battery compartment cover(p.6) 5

8 Preparation Before Use 1. Installing the Batteries Open the cover and install two AA batteries (excluded)according to the + and - marks, rechargeable batteries of 1.2V can be used. When in low battery, the status indicator light will blink(red) separately, at the moment need to replace battery. Remove the batteries when the product is not used for long time. Please replace the both two batteries at the same time. 2.Attaching and Detaching the Transmitter 1).Attach the transmitter. Slip the transmitter's mounting foot all the way into the camera's hot shoe. 2). Secure the transmitter. On the mounting foot, slide the lock lever to the right. When the lock lever clicks in place, it will be locked. 3).Detach the transmitter. While pressing the lock-release button, slide the lock lever to the left and detach the transmitter. It is supported that install a flash on the hot shoe of the transmitter(on-top flash). 6

9 Preparation Before Use 3.Install Flash on the Hot Shoe of the Transceiver (as Receiver) 1. Install the transceiver into the flash bracket or other fixing devices (Not included in the product box). 2.Make sure the mounting foot lock of the flash is released 3.Slide the flash s mounting foot into the transceiver s hot shoe fully. 4.Lock the flash in place. Caution! The hot shot of the transceivers can only install flash being applicable to DSLR cameras, can not install highv o l t a g e f l a s h, o r t h e transceiver may be damaged.! Check that all equipments are installed and connected reliably before use, turn all equipments on, setting the transceivers in the same channel, set the group of receivers, test button can be used to awaken and test whether the flash works before shooting(refer to Page 10), trigger the flash until flash recyling completely. 7

10 Setting 1.Power switch The YN622C II adopts 3 sections of power switch design. When it set in the 622 communication mode, the red indicator light will bright, when set in the 560-RX communication mode, the orange indicator light will bright, OFF for power off. When it used with the YN622C series products, please set the power switch on 622 position,transmitting/receiving mode will automatically switched. For the relevant usage of 560-RX please refer to page 25. Red Indicator (622mode) Orange Indicator (560-RX mode) 2. Channel Setting (Shortly Press [CH SET] Button) Shortly press [CH SET] button and the channel indicator will keep lighting for several seconds to indicate the current channel, shortly press [CH SET] button again to change channel, and there are totally 7 channels. Set all the transceivers at same channel. Ch1 Ch2 Ch3 Ch4 Ch5 Ch6 Ch7 3. Receiving Group Setting (Press [GP SET] Button) Short press [GP SET] button to check the current receiving group, then shortly press [GP SET] button again to change among A/B/C three groups. 8

11 Setting 4.Flash Test Group Setting (Test + GP SET Button) Set flash testing group Type C camera uses the set firing group. YN622C Ⅱ RX OFF 1. H o l d d o w n [ Te s t ] b u t t o n t h e n t h e g r o u p indicators will keep lighting, the flash on the receiver group having been selected will be woken up(p.10). 2. Hold down [Test] button and repeat to shortly press [GP SET] button, selected groups of receivers to testing flash, and there are totally 7 combinations. 3. When loosening [Test] button, the flash of the group having been selected will fire a test flash(p.10). Testing group is different from firing group, firing g r o u p s e t t i n g of t y p e A c a m e r a r e f e r t o page 18 while page 22 for type B. 9

12 Flash Awaking and Testing Flash When half-pressing the shutter button of the camera, the hot-shoe flash on the receiver will be awakened. (for A/B type camera only) Under any connection type, [Test] button can be pressed to awaken and test the flash on the transceiver and other transceivers at the same channel. Test flash with the mode set by the flash, and under the mode of E-TTL it may fire in a lower output. Refer to the following figure, the transmitter sets A +B two groups of flash test, hold down the[test] button, the flash on A and B of the receiver will be awakened, and when loosening [Test] button will fire a test flash. YN622C II RX OFF If the flash can not be awakened, manually awaken the flash before shooting. Using PC port to connect with flash without the awakening function. All the indicators going out when flash fires. 10

13 Remote Control Mode Remotely setting all the flashes through the external flash function setting (camera menu) of the camera, just likes the flash being directly installed on the camera. The settings of camera menu is prior, settings will upgraded to the receiver after pressing down camera confirmation button or half pressing shutter button without needing to operate the flash control panel, the flash s screen will display the current setting. The setting varies depending on the cameras/flashes. This control mode is the default control mode, transmitter s channel indicator will goes out in standby state, the camera needs to be set at P/AV/TV/M exposure mode, and it for type A cameras only. 1. Press down [MENU] button on the camera, select flash control-external flash function setting. When the off-camera setting which is consistent with the camera s menu, the AF assist beam emitter of the receiver will blink twice to show that the change is successfully.(p. 24) 2. Enabled the wireless flash function via the camera s menu to realize firing group control.(p.17) 3. Focus and shoot picture, the flash is fired according to the parameters set of all groups. Support the function of AF assist beam emitter of the transmitter. (p.24) Suggest disabled wireless flash function when using 2st curtain sync only. 11

14 Automatic Flash (E-TTL II) Fully-automatic Flash Shooting 1. Select flash mode as E-TTL II mode. 2. Half press camera's shutter button to focus, and on the flash screen the aperture and effective range etc. parameters will be displayed. 3. Ensure that the subject is in the effective flash range, full press camera s shutter button to shoot, the flash will be fire according to the setting. Exposure lever increments may set to 1/3-stop via the camera. vthe following E-TTL functions are advanced application, please refer to the usermanual by the manufacturer of the camera and flash. E-TTL II metering FEL: Flash Exposure Lock Modeling flash 12

15 Shutter Sync 1. 1st Curtain sync The normal flash sync. 2. 2nd curtain sync The flash fires right before the shutter closes, lower shutter speed needs to be used, support bulb 2nd curtain sync flash. Only when wireless flash function via the flash control menu is disable, the 2nd curtain sync can be use. 3. Hi-speed Sync(HSS/FP FLASH) The flash can sync with all shutter speeds when using HSS. The max speed is 1/8000s or 1/4000s(depends on the camera). In case of using hot-shoe flash which does not support hispeed sync, the max sync speed is 1/250s or less. 13

16 FEB/FEC(E-TTL only) 1. FEB (Flash Exposure Bracketing) Support 1/3-stop increments to set FEB within ±3. The sequence of FEB is fixed at 0 - +, even the FEB sequence of the custom setting in flash is different, the shoot sequence remains to either. FEB function will be automatically cancelled af ter three shots are taken. Even the E-TTL flash does not support FEB can also realize this function. 2. FEC (Flash Exposure Compensation) Support 1/3-stop increments to set FEC within ±3. The FEC button of the camera can also be use.! Setting value will be show on the flash screen when halfpressing the shutter button. Till FEB and FEC of the flash are set to 0, settings could be changed by remote control of camera menu, and you can also set each of the flash FEB and FEC via its control panel, compensation value shall be superposed according to flash setting plus camera menu setting, for example, the camera menu is set to -3, and the flash is set to +3, then exposure compensation shall be 0. 14

17 Zoom (Flash Coverage) Zoom supports automatic/manual setting. 1. With automatic setting, focal length of the flash may change with lens focal length. 2. With manual setting, focal length of the flash supports manual setting within MM. 1. Automatic Setting 2. Manual Setting 3. Zoom Lock Hold down the [CH SET] button of the receiver for seconds until channel indicator keeps lighting (same to set the mix control mode for the transmitter, p.21), enable the zoom lock function for the receiver, then the flash on the receiver will not be controlled by the camera menu, adjust flash zoom settings with flash control panel (automatic or manual), that means each flash can be set with a different focal. Hold down the [CH SET] for seconds again to cancel. 15

18 Manual Flash/ Multi Flash 1.Manual Flash: Manually set flash output (1/128~1/1 power 1/3-stop increments) Select flash mode as Manual Flash Mode, setting flash output,shutter sync, zoom etc. 2.Multi Flash (Stroboscopic flash) Select flash mode as Multi Flash, setting via the camera menu. Items Flash Output Frequency Flash count Zoom! The three parameters of flash output, frequency, and flash count may restrain each other, setting details may be referred to user manual of flash manufacturer. Factual output shall be subject to the flash s screen display. 16 Parameter Manual(Max1/4) 1-199hz 1-100times Auto/Manual(24-105mm)

19 Wireless Function* By setting the wireless flash function menu, in a different flash mode or firing group, remotely set A / B / C, three groups of flash ratio or flash output. 1. Enabled the wireless function via flash control menu. 2. Master Flash: Option for a flash which installed on the transmitter(on-top flash), select enable for firing or disable. On-top flash exposure setting as well as group A. The on-top flash just like a flash installed in receiver, which supports E-TTL, manual flash, multi flash mode and can cooperate with other off-camera flash using. It supports the function of AF assist beam emitter(p.24), disabled the wireless function can also be used the on-top flash. The zoom of the on-top flash will not be controlled by the camera menu, adjust zoom settings with flash control panel (auto or manual), that means you can make the zoom setting of the ontop flash different from other off-camera flash, such as auto set for the on-top flash(via control panel), manual set for the offcamera flashes(via camera menu). Enable the wireless flash function, 2nd curtain sync function will be unable to use. For 5D MarkIII, 650D and other new models, selecting the optical transmission menu insteads of wireless function. * YN622C is corresponding to optical pulse transmission wireless function. 17

20 Wireless Function 3.Channel Setting via Wireless Function Set channel (CH1-CH4 only) of the transmitter via wireless function setting, the changed shall cover the original setting. CH1-CH7 may also be set by directly pressing [CH SET] at the transmitter(p.8). 4. Firing Group Setting via Wireless Function Sets firing group of the transmitter via wireless function setting, in transmitting communications, state indicator and group indicator both blinking green, the following table shows that each group indicator stands for different firing group available. YN622C II RX OFF Group Indicator Indicator A blinks Indicator B blinks Indicator C blinks Indicator goes out Firing Group ALL(A+B+C) (A:B) A:BC or A:B:C ALL(A+B+C) When disabled the wireless function via the camera menu, in transmitting communications, group indicator will go out, firing group consists of all (A+B+C), all groups of flashes using the same setting. 18

21 Flash Ratio with E-TTL II Flash fire ratio and FEC of the A, B, C three firing groups can be set under E-TTL II flash mode. 1.All (A+B+C) R a t i o o f f, A / B / C t h r e e flashes automatically fire with same output, flash e x p o s u re c o m p e n s a t i o n (FEC)can be set. 2.A:B Set fire ratio (8:1-1:8, 1/2- stop increments) and flash exposure compensation for flashes of Group A and B, Group C does not fire. 3.A:BC Set fire ratio and FEC for flashes of Group A and B, FEC of Group C can be set solely (Group C flash may be overexposure to the subject, suitable for use as a backlight). 19

22 Manual/Multi Flash Output Flash output for each group A/B/C can be separately set under Manual/Multi flash mode. 1. All (A+B+C)-The three groups of flashes shall be set with the same output. 2. A: B-Group A and B shall be separately set, Group C flash will not fire. 3. A: B: C-Group A, B, C shall be separately set. Flash output under menu root is same to Group A. 20

23 Mix Control Mode Set the flash on each receiver in different flash modes as Manual/E-TTL/Multi for mix control, the settings of the flash is prior, channel indicator of the transmitter will keep lighting when enabled this control mode. Supports type A/B cameras using. 1. Hold down the [CH SET] button for several seconds of the transmitter until the channel indicator blinks for 3 times and then keep lighting, enable the mix control mode. 2. Flash mode of the transmitter will be fixed at E-TTL and the zoom setting is disabled. 3. Set the parameters of each flashes via it own control panel. In the mix control mode, set items via the flash it supports: Flash mode (output), FEB, FEC, Zoom etc. Set the shutter sync via camera menu and the flash set is invalid (Type B camera defaults to hi-speed sync). Disable the mix control mode by hold down [CH SET] button again then it will return to remote control mode (the channel indicator goes out in standby state).(p.11) 21

24 Flash Triggering of B/C Type Camera Type B Cameras: There is no flash control menu of such type of cameras that some of function will be restricted. Enable the mix control mode of the transmitter before using(p.21). 1. Setting of transmitting groups (set in the transmitter when it in transmitting status): Half press the camera s shutter button then status indicator blinks green. Press [GP SET] to set transmitting firing groups. Group Indicator Indicator A blinks Indicator B blinks Indicator C blinks Firing Group ALL(A+B+C) (A:B) ALL(A+B+C) 2. Setting of flash mode (via the flash control panel): 1). Automatic (ETTL) mode supports automatic flash, supports the settings of FEC and FEB, it defaults to hi-speed sync. 2). Manual (M) mode, manually set the flash output. It defaults to hi-speed sync. 3). Multi mode, set according to the flash. Type C Cameras: Manually set the Flash Output 1. Transmitting group set (via the transmitter): Set according to testing group of transmitter (p.9). 2. Flash mode set (via the flash control panel): Set the manual(m) flash output via the control panel of the flash, and trigger with transmitter's main flash contact(single contact). Do not support hi-speed sync or other TTL functions.(max speed sync is 1/250s or less) 22

25 PC Port Triggering (Support Super Sync *) Caution! Do not connect to the PC port any flash requiring trigger voltage more than 300V, or the transceiver may be damaged. Purchase corresponding PC flash sync cord according to the different ports of the flashes needs. 1. Use an end of PC sync cord with nut to connect to the receiver. 2. The other end of the PC sync cord connects to strobe flashes or other flashes which supporting PC port. 3. Set the camera's shutter sync as 1st curtain or 2nd curtain. 4. Adjust shooting parameters and shoot. * Super sync: Use the non-high speed sync flash to realize higher sync speed, this function is more applicable to strobe flashes whose flash duration is longer. (PC port output only) 1. Connect the receiver to flash via PC port and it may needs setting at manual full-power flash output (1/1). 2. Use manual exposure or shutter-priority mode, set the shutter sync as hi-speed sync, the maximum shutter sync speeds can reach to 1/8000s. Take photos and check whether the photos are synchronous, it may see gradations or variations in the photos, results depend on the camera and flash. The PC port is for output using only. Flashes on the hot shoe and connecting to the PC port can be used at the same time. For type C camera, the max PC sync speed is 1/250s or less. 23

26 References AF Assist Beam Emitter When using AF under low-light, the built-in AF-assist beam emitter of the transmitter will be emitted automatically to make it easier to autofocus, and the flash on the transmitter which support AF assist beam emitter function can also be emitted at the same time. It needs using single autofocus for the lens. It needs enabled the AF assist beam function of camera (flash) by custom functions setting. Can also disable this function by custom functions setting(c.fn8). Both the receiver and the off-camera flash on the receiver will not be emitted. Feedback Function of the AF Assist Beam Emitter When the off-camera setting which is consistent with the camera s menu, the AF assist beam emitter of the receiver will blink twice to show that the change is successfully. Only when the flash which supports assist beam emitter function is set in the receiver and the assist beam emitter is available, can this function be used. Install the receiver on the camera and set the assist beam firing as disable via external flash custom function setting camera menu to disable this function(sets will be saved). If parameter which the flash doesn t support had been set (such as hi-speed sync), this function will be abnormal. 24

27 Reference-About 560-RX The YN622C II supports receiving the triggering signal YN560-TX (RF603 communication mode),when using the compatible flash, it can wireless control the flash mode, flash output and zoom of each group; meanwhile supports the triggering signal(the flash set to M mode) of the RF603(II) RF605(RF603 communication mode). Supports grouping function of the YN560-TX RF Set to the 560-RX mode through the power switch. 2.Set the same channel as the transmitter (Shortly press the CH SET button). Ch1 Ch2 Ch3 Ch4 Ch5 Ch6 Ch7 3.Set the receiving group (press the GP SET button). 4.Shoot and trigger the flash. When the power switch set to 560-TX, it is recommended only use the YN560-TX/RF603/RF605 as transmitter, the YN622C II as receiver. If it is used as transmitter in this communication mode, it will transmit as 622 communication mode. 25

28 YN622C II RX OFF References Firmware Update 1.Log in the YONGNUO official website: to download the firmware update software and the latest firmware. 2.Power off, use Micro-USB(do not include) cable connect to PC. 3.Press the <CH SET> button and set the power on, all the indicator bright(green). 4.Complete the firmware upgrade operation according to the prompt of software. YN622C Ⅱ RX OFF Factory Reset YN622C II RX OFF 1) Hold down the buttons [CH SET] plus [GP SET] at the same time. 2) The state indicators will blink for 3 times in red-green alternately then turn to keep lighting (red). 3) Release all the buttons then reset the factory set. About Automatic Saving Function The transceiver will automatically save the sets such as channel, receiving group, AF assist beam. In the TTL set, some parameters will not be saved, such as the set of fire ratio etc. 26

29 Troubleshooting 1. Fail to power on or automatic shutdown: The battery is loaded inversely or exhausted; the status indicator light will blink(red) separately when the battery is going to be exhausted, and it will power off automatically in case of being over discharged. Install the battery according to the correct direction, ensure the battery is full and restart the power (refer to page 8). 2.The flash doesn't fire: Ensure the power of all are full, the connection among the transceiver, camera and the flash is reliable; whether the indicator is set in the same channels and controllable groups. Flashes recycle process, entering in the state of overheating protection, the flash enters into sleep status etc. may makes the flash doesn't fire. Ensure the flash is in ready state, use the [Test] button test the flash before using. Check the power switch of the receiver to see if it set to correct communication mode. Such as the receiver set to 560-RX mode, it will not receive the signal of 622". 3. Fail to enable the 2nd curtain sync: That s because the restriction of camera menu. It shall set the wireless function disabled if needs using the 2nd curtain sync. 4. Can't access into the external flash function menu or the menu is displayed abnormally: The transmitter is not installed right, the contacts of the hot shoe is stained or the power of the battery is exhausted. Reinstall the transmitter and clean the contacts,replace the batteries. 5.The channel indicator bright all along, unable to change the flash mode and zoom of camera menu. It is because enable the mix control mode. Please long press the CH SET button to exit the mix control mode or restore to factory settings. 27

30 Troubleshooting 6. The assist beam emitter doesn't work: Refer to page The on-top flash doesn't fire: Enabled the master flash via the wireless function setting. 8. Can't set the flash zoom via camera menu: W h e n t h e m i x control mode has been set in the transmitter (p.21) or zoom locking has been set in the receiver (p.15), zoom can't be set via camera menu. Zoom setting of the on-top flash needs to be set separately(p.17). 9. Fail to set channel 5, 6, 7 via camera menu: This is caused by the camera restriction and it can only set the channel 1-4 in via camera menu, while other channels can be set via channel button. 10.ETTL underexposure or overexposure:suggest enable wireless flash function when using ETTL flash mode, and adjust the position of the flash, use FEC/FEL function, check flash s effective range. It may overexposure when ETTL and manual flash are used at the same time, now the manual flash suits to be used as a backlight. 10.Information of aperture, distance are not displayed on the flash when half pressing the shutter:set compatiable flash mode/shutter sync with the flash on the transmitter. 11.No effect of the flash exposure bracketing calculation on receiver: Set the flash mode which is compatible with the flash. vit is suggested using the following procedures to deal with when other trouble occur during the using: 1). Restart all the equipments. 2). Replace the batteries of the transceivers. 3). Reset the factory set of the transceivers/camera/flash. 4). Install the hot-shoe flash on the camera directly and clear the custom function of external flash then install it on transceiver again. 28

31 Specifications System type: Digital FSK 2.4GHz wireless transceiver Distance: 100M Channel: 7 Flash mode: E-TTL(II), Manual flash, Multi flash Sync mode: 1st curtain, 2nd curtain, Hi-speed sync Groups: A/B/C 3Groups(622);A/B/C/D/E/F 6Groups (560-RX) Max Sync speed: 1/8000s* Input: Hot-shoe(TTL,main contact) Output: Hot-shoe, PC port Firmware upgrade terminal: Micro USB Applicable battery: AAX2 (support 1.2 V rechargeable battery) Stand-by time: 60h Dimensions: 91.5X53.5X43mm Net Weight:89g *About the Max Sync Speed It needs the camera and flash both support hi-speed sync, and the max sync speed is 1/8000s or 1/4000s. When using the hot shoe flash which doesn t support hi-speed sync, the max sync speed is 1/250s or lower. Sync speed of part of cameras and flashes may be lower. All of the specification parameters are base on test conditions of our company. All registered trademarks are the property of their respective owners in this user manual. Specifications subject to change without notic. Updated version of the user manual can be got from 29

32 注意事项目录 通用描述 产品功能简介 支持的功能列表 兼容性列表 各部位名称 使用前准备 设置 闪光灯唤醒 测试引闪 远程控制 ( 遥控 ) 模式 混合控制模式 B/C 型相机闪光触发 PC 接口触发 参考 故障排除 规格 注意事项 连接或安装本产品时, 请关闭所有设备电源 请保持干燥, 勿用湿手接触产品, 亦不可将产品浸入水中或暴露雨中, 否则可能引起无法正常使用, 甚至损坏 请勿在易燃易爆场合中使用, 违反此警告可能引起爆炸或火灾 本产品涉及电池, 关于电池的使用请严格按照相关规定, 否则会引起财产损失或人身伤害 v 使用前请先阅读您的相机与闪光灯的说明书, 并通读本使用手册, 以确保能正确使用本产品的功能

33 RX OFF 通用描述 本产品为无线收发一体设计, 自动切换发射 接收状态 为方便表述, 本说明书中将安装于相机热靴时将称之为发射器 ( 主控单元 ), 安装或连接闪光灯时将称之为接收器 ( 从属单元 ) 闪光灯菜单 ( 相机菜单 ) YN622C II LCD 屏幕显示 YN622C-TX 推荐选购 YN622C-TX 无线引闪控制器作为发射器使用, 有关此产品的介绍, 请浏览以下网页 : 1

34 产品功能简介 首先感谢您选购永诺产品 全新升级版 YN622C II 可通过电源开关设置在 622 或 R X 通信模式, 支持接收 Y N TX/RF605(603 模式 )/RF603(II) 系列产品的引闪信号, 拥有多项细节改进, 并使用了快速锁定设计, 支持 USB 固件升级 YN622C II E-TTL 无线引闪器是高性能的多灯摄影主控及受控设备, 通过数字 FSK 2.4GHz 无线传输, 可在 360 度布置你的闪光灯, 实现不同的拍摄效果 采用收发一体的设计, 遥控距离可达 100M, 支持 7 个无线频道及 A/B/C 三个分组 安装在支持外接闪光灯菜单的佳能 EOS 系列单反相机, 可实现快速地更改远程闪光灯的模式及参数, 如 TTL 分组光比或手动控制每组闪光灯的闪光输出 支持高速同步, 最高同步速度 1/8000s*, 有 E-TTL M 多次闪光模式, 支持机顶发射器安装 E-TTL 闪光灯 使用 TTL 功能需兼容的相机及闪光灯 部分相机机型最高同步速度为 1/4000, 使用不支持高速同步的相机与闪光灯, 最高同步速度为 1/250 或更低 2

35 支持的功能列表 快速锁定设计 支持 USB 固件升级 支持 622 通信模式,560-RX 通信模式 支持的闪光模式 :E-TTL(II), 手动, 频闪闪光 快门同步 : 前帘同步, 后帘同步, 高速同步, 支持最高同步速度为 1/8000s 支持通过相机菜单远程设置闪光灯参数 ( 远程控制 ) 支持 E-TTL, 手动, 频闪闪光混合使用 ( 混合控制 ) 支持发射端机顶安装闪光灯并支持 ETTL 功能 支持闪光灯头变焦 ( 自动, 手动 ) 支持曝光补偿 (FEC) 支持包围曝光 (FEB) 支持曝光锁定 (FEL) 支持景深预览造型灯闪光 支持 ETTL 光比 (ALL/A:B/A:BC) 支持手动 频闪分组 (ALL/A:B/A:B:C) 支持辅助对焦灯功能 支持 PC 接口触发影室灯, 并支持前帘同步, 后帘同步, 高速同步 ( 超级同步 ) 支持 LCD 实时取景状态下正常引闪 支持高速连拍触发闪光 设置自动保存功能 兼容永诺全系列闪光灯 佳能全系列 EXII 闪光灯 支持单触点闪光相机 / 闪光灯触发 ( 最高同步速度为 1/250s) 3

36 兼容性列表 本产品所支持的功能取决于使用的相机及闪光灯, 针对使用的相机不同, 本说明书中将具备外接闪光灯控制功能菜单的 EOS 单反相机称为 A 型相机 ; 不具备外接闪光灯控制功能菜单的 EOS 单反相机称为 B 型相机 ; 其他带标准热靴的相机品牌称为 C 型相机 A 型相机列表 Canon EOS 1DX/5D Mark II/5DMark III/1Ds Mark III/ 1D Mark IV/1D Mark III/6D/7D/7DII/70D/60D/ 50D/40D 450D/500D 系列 /600D 系列 /700D 系列 /1000D 系列 B 型相机列表 Canon EOS 5D/10D/20D/30D/300D/350D/400D/1D/1D Mark II 兼容的 ETTL 闪光灯列表 ( 支持通过相机菜单无线遥控 ) Canon 600EX(RT)/580EXII/430EXII/320EX/270EX(II) 永诺 YN600EX-RT/YN568EX(II)/YN565EX(II)/ YN500EX/YN468(II)/ YN467(II)/YN EX/550EX/580EX 等部分闪光灯不支持通过相机菜单遥控, 需手动设定闪光灯闪光模式及参数 使用通用型手动闪光灯及 PC 接口触发影室闪光灯, 需要手动给闪光灯设置功率 如无特别说明, 本说明书假定您正在使用 A 型相机及兼容的 ETTL 闪光灯, 对于 B/C 型相机, 请参阅第 22 页 4

37 622 各部位名称 / 指示灯状态说明 指示灯名称 闪烁 常亮 频道指示灯 通信中 ( 远程控制模式 ) 混合控制模式 分组指示灯 闪光组或接收分组 测试通信中 状态指示绿灯 622 模式发射通信中 测试通信中 状态指示红灯 622 模式接收通信中 待机状态 状态指示橙灯 560-RX 模式接收通信中 待机状态 此处保护薄膜可以撕去 Q R 560-RX OFF 辅助对焦灯 ( 第 24 页 ) 频道设置按钮 ( 第 8,9 页 ) 测试按钮 ( 第 9,10 页 ) PC 座 ( 第 23 页 ) 频道指示灯 ( 第 8 页 ) 分组指示灯 ( 第 8,9 页 ) K 热靴座 ( 第 6,7 页 ) 分组设置按钮 ( 第 8,9 页 ) 电源开关 ( 第 8 页 ) 状态指示灯 ( 第 5 页 ) 防尘防水滴适配器固定座锁定杆 ( 第 6,7 页 ) 锁定释放按钮 USB 插座 ( 第 26 页 ) 热靴固定脚 ( 第 6,7 页 ) 锁定销 ( 第 6 页 ) 电池仓 ( 第 6 页 ) 电池仓盖 ( 第 6 页 ) 5

38 使用前准备 1. 安装电池 打开电池仓, 根据电池仓正负极方向安装两节 AA 电池 ( 不含 ), 可以使用两节 1.2V 充电电池 电池电量不足时, 状态指示灯将会单独闪烁, 此时需更换电池 长期不使用产品请将电池取出 更换电池时, 请两节一起更换 2. 安装 / 取下发射器 1). 将固定座完全滑入相机的热靴插座 2). 将固定座上的锁定杆滑动到右侧, 在锁定杆发出咔嚓声的位置, 发射器将被锁定 3). 按住锁定释放按钮的同时向左滑动锁定杆, 取下发射器 支持在发射器热靴安装闪光灯 ( 机顶闪光灯 ) 6

39 使用前准备 3. 安装闪光灯于收发器热靴 ( 作为接收器 ) 1. 将收发器安装在闪光灯附带的微型支架或其他固定装置 ( 不含 ) 2. 松开闪光灯锁定装置 3. 将闪光灯热靴固定脚完全插入收发器热靴座 4. 锁紧闪光灯锁定装置 注意! 收发器热靴只能安装数码单反适用的闪光灯, 不能安装高压闪光灯, 否则可能损坏收发器! 使用前检查所有设备安装及连接可靠, 打开所有设备电源, 收发器设置在相同的频道, 设定接收器闪光组, 拍摄前使用测试按钮唤醒及测试闪光灯是否正常 ( 参考第 10 页 ), 在闪光灯完全回电后触发闪光灯 7

40 设置 1. 电源开关 YN622C II 产品使用 3 段式电源开关设计, 设置在 "622" 通信模式, 状态指示灯亮红色, 设置在 "560-RX" 通信模式, 状态指示灯亮橙色, "OFF" 为电源关闭 红色指示灯亮 (622 模式 ) 配合 YN622C 系列产品使用, 请将电源开关设置在 622 位置, 自动切换发射 接收状态 有关 560-RX 模式的使用, 请参考说明书第 25 页 2. 设置频道 ( 短按 CH SET 按钮 ) 待机状态下短按 CH SET 按钮, 频道指示灯显示当前的频道, 再短按一次 CH SET 按钮切换, 共有 7 个频道 将要控制的发射 接收器设置在相同的频道 Ch1 Ch2 Ch3 Ch4 Ch5 Ch6 橙色指示灯亮 (560-RX 模式 ) Ch7 3. 设置接收分组 ( 短按 GP SET 按钮 ) 短按 GP SET 按钮查看当前接收分组, 再短按一次 GP SET 按钮将在 A/B/C 3 个分组间切换 8

41 设置 4. 设置闪光测试分组 (Test+ GP SET 按钮 ) 设置闪光测试分组 C 型相机使用此设置发射分组 ( 闪光组 ) YN622C Ⅱ RX OFF 1. 在待机状态下按住 Test 按钮不放, 分组指示灯保持常亮, 同时会唤醒已选分组的闪光灯 ( 第 10 页 ) 2. 按住 Test 按钮不放并重复短按 GP SET 按钮设置测试闪光分组, 共有 7 种组合 松开 Test 按钮的同时, 所选分组的闪光灯将被测试闪光一次 ( 第 10 页 ) 设置测试闪光分组与设置发射分组 ( 闪光组 ) 不同, A 型相机相机发射分组设置参考第 18 页,B 型相机参考第 22 页 9

42 闪光灯唤醒 测试引闪 半按相机快门按钮时 ( 限 A/B 型相机 ), 接收器上的热靴闪光灯将被唤醒 任何连接方式下均可通过按下收发器 Test 按钮唤醒及测试该收发器以及相同频道收发器上的闪光灯 将以闪光灯所设定的模式测试闪光, 在 E-TTL 模式下将会以较低亮度闪光 下图中, 发射器设置了 A+B 两组闪光测试, 按下 Test 按钮接收器 A 与 B 上的闪光灯将被唤醒, 在松开 Test 按钮时, 闪光灯将测试闪光一次 YN622C II RX OFF 若闪光灯不能被唤醒, 需在拍摄前手动唤醒该闪光灯 使用 PC 接口连接闪光灯将不支持唤醒功能 触发闪光的瞬间, 所有指示灯将熄灭 10

43 远程控制 ( 遥控 ) 模式 通过相机外接闪光灯菜单 ( 相机菜单 ) 遥控更改所有闪光灯的设置, 与闪光灯直接安装于相机的操作方式相同 设置将以相机菜单为优先, 更改的设定在按下相机确认按钮或半按相机快门按钮后同步更新到闪光灯而无需操作闪光灯控制面板, 闪光灯屏幕显示当前设定, 不同相机及闪光灯支持设置的参数将有所区别 遥控模式为默认的控制模式, 发射器在待机状态中频道指示灯熄灭, 相机需设定在 P/AV/TV/M 曝光模式, 本功能限 A 型相机使用 1. 按下相机菜单按钮, 选择闪光灯控制 - 外接闪光灯功能设置, 选择闪光模式及参数并设置, 当离机闪光灯被更改的设置与相机闪光灯菜单一致时, 接收器辅助对焦灯将会快速闪烁两次表示修改成功 ( 第 24 页 ) 2. 可启用无线闪光功能以实现分组控制 ( 第 17 页 ) 3. 对焦并拍摄照片, 根据设置的闪光灯各分组参数闪光 支持发射器辅助对焦灯功能 ( 第 24 页 ) 建议仅在使用后帘同步时关闭无线闪光功能 11

44 自动闪光 (E-TTL II) 全自动闪光拍摄 1. 选择闪光模式为 E-TTL II 模式 2. 半按相机快门按钮进行对焦, 闪光灯屏幕显示光圈 有效距离等参数 3. 检查拍摄主体是否在闪光的有效距离内, 全按相机快门按钮拍摄相片, 将根据设置自动输出闪光 需在相机内设置曝光增量等级为 1/3 级 v 以下为 TTL 功能高级应用, 有关相机及闪光灯的操作及技巧, 请参考制造商提供的说明书 E-TTL II 测光 FEL: 闪光曝光锁定 造型灯闪光 12

45 快门同步 1. 前帘同步 正常的闪光同步 2. 后帘同步 在快门即将关闭前闪光, 需使用较低的快门速度, 支持 B 门后帘同步 只有当闪光灯菜单中的无线闪光功能设为禁用时, 才可使用后帘同步 3. 高速同步 使用高速同步, 可以在所有快门速度下使用闪光灯同步 最高同步速度为 1/8000s 或 1/4000s( 取决于相机 ) 不支持高速同步的热靴灯, 最高同步速度为 1/250s 或更低 13

46 闪光包围 / 曝光补偿 ( 限 ETTL) 1.FEB 闪光包围曝光 支持在 ±3 的范围内以 1/3 步长设置闪光包围曝光 曝光包围的顺序固定为 0 - +, 即使闪光灯的自定义功能菜单中的设置与此顺序不相同, 拍摄的顺序仍然为 完成一次曝光包围闪光 ( 三次拍摄 ) 后, 自动取消此功能 即使不支持包围曝光功能的 E-TTL 闪光灯, 也可实现此功能 2.FEC 闪光曝光补偿 支持在 ±3 的范围内以 1/3 步长设置闪光曝光补偿 支持使用相机的闪光曝光补偿按钮设置! 设置值在半按相机快门按钮时显示在接收器上的闪光灯屏幕 仅当闪光灯的曝光包围及曝光补偿设置为 0 时, 可通过相机菜单遥控更改设置 支持操作各闪光灯控制面板更改其曝光包围及曝光补偿设置, 补偿值根据该闪光灯 + 机身菜单设置叠加, 如机身闪光灯菜单设置为 -3, 闪光灯设置为 +3, 则曝光补偿为 0 14

47 ZOOM 灯头变焦 ( 闪光覆盖范围 ) 闪光灯头变焦支持自动 / 手动设置 1. 使用自动设置, 灯头焦距会跟随镜头焦距变化 2. 使用手动设置, 灯头焦距支持手动 MM 范围设置 1. 自动设置 2. 手动设置 3. 灯头焦距锁定 接收器在待机状态下长按 CH SET 按钮数秒直至频道指示灯保持常亮 ( 与发射器设置混合控制模式相同, 见第 21 页 ), 打开接收器焦距锁定功能, 此时接收器上的闪光灯焦距将不受相机菜单控制, 通过操作闪光灯控制面板调整闪光灯的焦距设置 ( 自动或手动 ), 可使每支闪光灯设置在不同的焦距 再次长按 CH SET 按钮取消本功能 15

48 手动闪光 多次闪光 ( 频闪 ) 1. 手动闪光 : 闪光输出在 1/128~1/1 1/3 步长设置 设置闪光模式为手动闪光模式, 更改闪光输出, 快门同步, 变焦等参数 2. 多次闪光 ( 频闪 ): 设置闪光模式为多次闪光, 通过相机菜单更改设置 设置项目 参数 闪光输出 手动 ( 最高支持 1/4) 闪光频率 1-199hz 闪光次数 次 闪光灯变焦 自动 / 手动 (24-105mm) v 闪光输出 频率 闪光次数三个数值会相互限制, 详细设置可参考闪光灯制造商的说明书 实际输出以接收器上的闪光灯显示为准 16

49 无线闪光功能 * 通过设置相机无线闪光功能菜单, 在不同的闪光模式远程设置 A/B/C 三组闪光灯的光比或闪光输出 1. 在外接闪光灯菜单中将无线闪光功能设置为启用 2. 主控闪光 : 安装在发射器上的闪光灯 ( 机顶闪光灯 ) 选项, 选择启用 ( 闪光 ) 或禁用 ( 不闪光 ), 机顶闪光灯有关曝光的选项等同 A 组设置 安装于发射器上的闪光灯, 支持相当于接收器所支持的功能, 包括 E-TTL 手动闪光 多次闪光模式, 可配合其他接收器离机无线闪光, 并支持闪光灯辅助对焦灯功能 ( 第 24 页 ) 机顶灯变焦将不受相机外接闪光灯菜单控制, 通过操作机顶闪光灯控制面板更改为自动或手动变焦设置, 既你可以使用机顶闪光灯与离机闪光不同的焦距设置, 如机顶灯设置为自动 ( 通过闪光灯面板 ), 离机闪光灯设置为手动 ( 通过相机菜单 ) 即使未启用无线闪光功能也可使用发射器机顶灯 启用无线闪光功能后, 将不能使用后帘同步 在 5D MarkIII 650D 等新机型中, 设置无线闪光功能选择光传输菜单 * 不对应光学脉冲传输的无线闪光功能 17

50 无线闪光功能 3. 设置频道 ( 通过无线闪光功能菜单 ) 4. 设置发射闪光分组 ( 通过无线闪光功能菜单 ) 通过无线闪光功能设置闪光组, 发射通信中, 分组指示灯会与状态指示绿灯同时闪烁, 分组指示灯的状态代表各可选的发射闪光组, 如下表 启用无线闪光功能后, 支持通过相机外接闪光灯菜单设置发射器的无线频道 ( 限 CH1-CH4), 更改的频道将覆盖原有发射器频道设置 也可直接按发射器 CH SET 按钮设置 (CH1-CH7) 见第 8 页 YN622C II RX OFF 分组指示灯指示灯 A 闪烁指示灯 B 闪烁指示灯 C 闪烁指示灯熄灭 禁用无线闪光功能后, 在发射状态通信状态中, 分组指示灯熄灭, 发射分组为全部 (A+B+C), 所有分组的闪光灯使用相同的设置 18 闪光组全部 (A+B+C) (A:B) A:BC 或 A:B:C 全部 (A+B+C)

51 E-TTL II 设置光比 在 E-TTL II 模式下, 可分别设置 ABC 三组闪光灯的闪光光比及闪光曝光补偿 1. 全部 (A+B+C) 光比关闭,ABC 三组闪光灯自动以相同功率闪光, 可设置闪光曝光补偿 2.A:B AB 两组闪光灯设置光比 (8:1-1:8,1/2 步长 ) 及闪光曝光补偿, C 组不闪光 3.A:BC AB 两组闪光灯设置光比及闪光曝光补偿,C 组单独设置闪光曝光补偿 (C 组灯对主体闪光可能过曝, 适合作为背景灯使用 ) 19

52 手动 / 频闪设置各组闪光输出 在手动 (M)/ 多次闪光 (Multi) 模式下, 可分别设置 A/B/C 三组闪光灯的功率输出 1. 全部 (A+B+C)- 三组闪光灯设置相同闪光输出 2.A:B-A 与 B 两组闪光灯分别设置闪光输出,C 组不闪光 3.A:B:C-ABC 三组闪光灯分别设置闪光输出 闪光灯菜单根目录下的闪光输出与 A 组参数设置相同 20

53 混合控制模式 设置各接收器上的闪光灯在 E-TTL/M/Multi 闪光模式混合使用, 将以闪光灯上的设置为优先, 发射器启用混合控制模式后频道指示灯在待机状态时保持长亮, 支持 A/B 型相机使用 1. 发射器在待机状态下长按 CH SET 按钮数秒直至频道指示灯闪烁三次后保持常亮, 打开混合控制模式 2. 发射器闪光模式将固定为 E-TTL, 变焦设置被禁用 3. 通过闪光灯的控制面板设定参数 在混合控制模式下, 支持在闪光灯上设置的项目 : 闪光模式 ( 功率输出 ), 曝光包围, 曝光补偿, 变焦等 快门同步请通过机身菜单设置, 在闪光灯上设置无效 对于 B 型相机, 默认为高速同步 取消混合控制模式可再次长按 CH SET 按钮数秒, 即恢复到远程控制模式 ( 待机状态时发射器频道指示灯熄灭 ) ( 第 11 页 ) 21

54 B/C 型相机闪光触发 B 型相机 : 此类相机无闪光灯菜单, 需打开发射器混合模式 ( 第 21 页 ), 一些功能将受到限制 1. 发射分组设置 ( 在发射状态中在发射器上设置 ): 半按相机快门按钮, 状态指示灯绿色闪烁时, 短按 GP SET 按钮更改发射分组设置 分组指示灯 闪光组 A 闪烁 A+B+C( 全部 ) B 闪烁 A+B C 闪烁 A+B+C( 全部 ) 2. 闪光模式设置 ( 在闪光灯上设置 ): 1). 自动 (ETTL) 模式, 支持自动闪光, 支持闪光曝光包围及曝光补偿设置, 默认为高速同步 2). 手动 (M) 模式, 手动更改闪光输出, 默认为高速同步 3). 多次 (Multi) 模式, 依据闪光灯设置 C 型相机 : 手动设置闪光输出 1. 发射分组设置 ( 在发射器上设置 ): 依据发射器测试分组设置闪光组 ( 第 9 页 ) 2. 闪光模式设置 ( 在闪光灯上设置 ): 通过闪光灯控制面板设置在手动闪光 (M) 模式, 手动更改闪光输出, 使用发射器主闪光触点触发, 不支持高速同步或其他 TTL 功能 ( 最高同步速度为 1/250s 或更低 ) 22

55 PC 接口触发 ( 支持超级同步 *) 注意! 请勿使用超过 300V 触发电压的闪光灯连接 PC 接口, 否则可能损坏收发器 需根据不同接口的闪光灯选购 PC 闪光灯同步线 1. 使用 PC 同步线带螺母一端连接接收器 2. 连接线另一端连接影室灯或其他支持 PC 接口的闪光灯 3. 设置相机快门同步为前帘 后帘同步 4. 调整拍摄参数并拍摄照片 * 超级同步 - 使用非高速同步闪光灯实现更高的同步速度, 本功能更适合闪光持续时间较长的影楼灯 ( 限 PC 接口输出 ) 1. 接收器通过 PC 接口连接闪光灯, 闪光灯可能需要设置在手动全功率闪光输出 (1/1) 2. 设置相机在手动曝光或快门优先模式, 把快门同步设置为高速同步, 快门同步速度最高可设置在 1/8000s, 拍摄并检查照片是否同步, 可能会看到光线的层次变化, 效果将根据相机及闪光灯不同会有所不同 PC 接口只作为输出 可同时使用热靴座上的闪光灯和与 PC 接口连接的闪光灯 使用 C 型相机,PC 同步速度最高为 1/250s 或更低 23

56 参考 辅助对焦灯 当光线不足以自动对焦时会启动辅助对焦灯功能, 发射器及发射器上的闪光灯辅助对焦灯会同时点亮以辅助镜头更容易对焦 需使用相机镜头自动对焦模式, 对焦模式设置为单次 AF 需在相机 ( 闪光灯 ) 自定义功能中设置辅助对焦功能启用, 也可以设置为禁用关闭辅助对焦灯功能 (C.Fn8) 接收器及安装在接收器上的闪光灯辅助对焦灯在相机自动对焦时均不会点亮 辅助对焦灯反馈功能 通过相机外接闪光灯菜单功能更改闪光灯支持的设置完成后, 接收器的辅助对焦灯将快速闪烁二次, 以提示远程设置成功 当接收器安装上支持辅助对焦灯功能的闪光灯且打开辅助对焦灯功能后, 本功能启用 关闭此功能, 可将该接收器安装于相机, 在相机的外接闪光灯自定义功能内设置辅助对焦灯功能为禁用 ( 设置的状态将被保存 ) 若设置了闪光灯不支持的项目 ( 如高速同步 ), 可能导致本功能异常 24

57 参考 - 关于 560-RX YN622C II 支持接收 YN560-TX(RF603 通信模式 ) 的引闪信号, 当使用兼容的闪光灯时, 可无线控制各组闪光灯模式 输出功率 焦距 ; 同时也支持接收 RF603(II) RF605(RF603 通信模式 ) 引闪信号 ( 闪光灯需设置在 M 模式 ) 支持 YN560-TX RF605 分组功能 1. 通过电源开关设置在 560-RX 模式 2. 设置与发射器相同的频道 ( 短按 CH SET 按钮 ) Ch1 Ch2 Ch3 Ch4 Ch5 Ch6 Ch7 3. 设置接收分组 ( 按下 GP SET 按钮 ) 4. 拍摄并引闪闪光灯 建议仅在使用 YN560-TX/RF603/RF605 作为发射器,YN622C II 作为接收器时将电源开关设置在 "560-RX", 如在此通信模式作为发射器使用, 将以 622 通信模式发射 25

58 YN622C II RX OFF 参考 固件升级 1. 登录永诺官网 : 下载升级程序及最新固件 2. 关闭产品电源, 使用 Micro-USB 连接线 ( 不含 ) 与电脑连接 3. 按住 CH SET 按钮的同时开机, 所有指示灯将以绿色点亮, 进入固件升级界面 4. 按软件上的提示完成固件升级操作 YN622C Ⅱ RX OFF 恢复出厂设置 YN622C II RX OFF 1.) 同时按住 CH SET + GP SET 按钮不放 2.) 状态指示灯将红绿交替闪烁三次后保持红色常亮 3.) 松开所有按钮即恢复出厂设置 关于自动保存功能收发器将自动保存频道, 接收分组, 辅助对焦灯等设置, 在 TTL 设置中, 一些参数将不能保存, 如设置的 TTL 闪光光比等 26

59 故障排除 1. 无法开机或自动关机 状态指示灯红色闪烁 : 电池装反或电池耗尽将无法开机 ; 电池即将耗尽时状态指示灯红色闪烁, 并会自动断电, 防止电池过放电 按照电池仓指示标志的正确方向安装 ( 更换 ) 电池, 并确保电池有电, 重新开启电源 ( 参考第 6 页 ) 2. 闪光灯不闪光 : 确保所有设备电池电量充足, 收发器与相机及闪光灯之间的安装连接可靠, 观察指示灯是否设置在相同的频道及可控制的分组, 闪光灯回电过程 进入过热保护状态 正在调整焦距或闪光灯休眠可能导致漏闪, 确保闪光灯在就绪的状态, 在使用前用测试按键唤醒及测试闪光灯 检查接收器电源开关是否设置为正确的通信模式 比如接收器设置了 560-RX, 将无法接收 622 的信号 3. 无法启用后帘同步 : 启用无线闪光功能后无法启用后帘同步, 这是由于相机菜单的限制 使用后帘同步功能, 应在相机外接闪光灯功能处设置无线闪光灯功能为关闭 4. 无法进入闪光灯外接功能菜单或菜单显示异常 : 发射器未安装到位, 或热靴底座触点有污迹, 电池电量不足也可能导致此现象 重新安装控制器, 并清洁相机与控制器热靴触点, 更换电池 5. 频道指示灯常亮, 无法通过相机菜单更改闪光模式及焦距 : 这是开启了 混合控制模式, 长按 "CH SET" 按钮退出混合模式或恢复出厂设置即可 27

60 故障排除 6. 辅助对焦灯不亮 : 见第 24 页 7. 机顶灯不闪光 : 在无线闪光功能中主控闪光设置为启用 8. 无法通过闪光灯菜单设置变焦 : 在发射器上设置了混合控制模式 ( 第 21 页 ), 接收器设置了焦距锁定 ( 第 15 页 ), 将无法通过菜单设置闪光灯焦距 机顶闪光灯变焦需单独设置 ( 第 17 页 ) 9. 无法通过机身菜单设置频道 5 6 7: 这是由于机身菜单限制造成的, 只能在机身菜单设置频道 1-4, 其他频道可通过频道按键设置 10. ETTL 闪光曝光不足或曝光过度 : 建议在使用 TTL 闪光时启用无线闪光功能, 并调整闪光灯位置, 使用曝光补偿 曝光锁定功能, 检查闪光灯有效范围 ; ETTL 与手动闪光模式混合使用时可能会过曝, 此时手动灯适合作为背景灯使用 10. 半按相机快门时闪光灯上的光圈 距离信息不显示 : 将发射器上的闪光模式 / 快门同步设置为与闪光灯兼容的模式 11. 接收器上的包围曝光计数不起作用 : 将发射器上的闪光模式设置为与闪光灯兼容的模式 v 如在使用过程中遇到其他故障, 建议进行以下步骤解决 : 1). 重启所有设备 2). 给收发器更换电池 3). 给引闪器 相机 闪光灯恢复出厂设置 4). 直接将热靴闪光灯安装于相机上并清除外接闪光灯自定义功能设置后再安装于收发器 28

61 规格 系统模式 : 数字 FSK 2.4GHz 无线收发器距离 : 100M 无线通道 : 7 个闪光模式 : E-TTL(II) 手动闪光 多次闪光同步模式 : 前帘 后帘 高速同步分组控制 : A/B/C 3 个组别 (622);A/B/C/D/E/F6 个组别 (560- RX) 最高同步速度 :1/8000s* 兼容闪灯 : 热靴闪光灯 影室闪光灯输入 : 热靴 (TTL 触发, 主触点触发 ) 输出 : 热靴 (TTL 输出 ),PC 接口输出固件升级接口 :Micro USB 接口适用电池 :AAX2 节 ( 支持 1.2V 充电电池 ) 待机时间 :60 小时体积 :91.5X53.5X43mm 重量 :89 克 * 有关最高同步速度使用高速同步需相机及闪光灯支持,1/8000s 或 1/4000s 为相机支持的最高同步速度 使用不支持高速同步的热靴闪光灯, 最高同步速度为 1/250s 或 1/200s, 部分相机与闪光灯的组合同步速度可能更低 所有规格参数是基于本公司的测试, 本手册提到的所有注册商标均归其所有者拥有, 设计规格或本用户手册如有变更, 恕不另行通知 最新版本的说明书及升级固件请访问 下载 29

62 序列号 SN. 产品名称 Product Model 用户名称 Name 地址 Address 故障说明 Failure Description 产品保修卡 Warranty card 购买日期 Purchase Date 联系电话 Phone 邮编 Zip Code

63 V1.0