深圳安博检测股份有限公司 Shenzhen Anbotek Compliance Laboratory Limited 报告编号 :R B 第 1 页, 共 17 页 Report No. Page of 锂电池 UN38.3 测试报告 Lithium Battery UN38.3

Size: px

Start display at page:

Download "深圳安博检测股份有限公司 Shenzhen Anbotek Compliance Laboratory Limited 报告编号 :R B 第 1 页, 共 17 页 Report No. Page of 锂电池 UN38.3 测试报告 Lithium Battery UN38.3"

枉穆
5 years ago
Views:

Lithium Cell 样品型号 (Model) : 6060100 检测日期 : 2017 年 05 月 02 日至 2017 年 05 月 17 日 Date of Test May.

1 第 1 页, 共 17 页锂电池 U38.3 测试报告 Lithium Battery U38.3 Test Report 委托单位 (Client) : 生产工厂 (Manufacturer) : USU019 样品名称 (Product) : 聚合物锂离子电芯 Polymer Lithium Cell 样品型号 (Model) : 检测日期 : 2017 年 05 月 02 日至 2017 年 05 月 17 日 Date of Test May. 02, 2017 to May. 17, 2017 报告日期 : 2017 年 05 月 17 日 Date of Report May. 17, 2017 批准 (Approved Signatory) 审核 Checked by 检测 Tested by : : 报告专用章 Stamp :

2 第 2 页, 共 17 页 1. 样品描述 (SAMPLE DESCRIPTIO): 样品名称 : Sample ame 聚合物锂离子电芯 Polymer Lithium Cell 委托单位 : 深圳市波导能源有限公司 Client USU019 委托方地址 : China Add. Of Client 电芯型号 : Cell Model 生产工厂 : Manufacturer 标称电压 ominal 充电电流 Charge Current 终止电压 Cut-off 测试开始日期 Client date 3.7V 额定容量 Rated Capacity 1000mA 最大连续充电电流 Maximum Continuous Charge Current 2.75V 最大放电电流 Maximum Discharge Current 2017 年 05 月 02 日 May. 02, mAh 18.5Wh 5000mA 5000mA 测试结束日期 Finished date 商标 Trademark 充电截止电流 End Charge Current / 100mA 充电限制电压 4.2V Limited Charge 2017 年 05 月 17 日 May. 17, 参考方法 (REFERECE METHOD) 联合国关于危险货物运输的建议书试验和标准手册 (ST/SG/AC.10/11/Rev.6) United ations Recommendations On The Transport Of Dangerous Goods, Manual Of Tests And Criteria (ST/SG/AC.10/11/Rev.6).

3 第 3 页, 共 17 页 3. 测试项目 (TEST ITEM) 1. 高度模拟 (Altitude simulation) 5. 外部短路 (External short circuit) 2. 温度试验 (Thermal test) 6. 挤压 (Crush) 3. 振动 (Vibration) 7. 过度充电 (Overcharge) 4. 冲击 (Shock) 8. 强制放电 (Forced discharge) 4. 本次检测所使用的设备清单 : Major instruments of measurement used in the test: 设备名称 / 型号编号校准有效期 ame of equipment Serial o. Due Date /Model 模拟高空低压试验箱 SE Low Pressure Test Machine BE-DY-125 快速温变箱 SE High and Low Temperature Chamber BE-THK-150M8 振动台 SE Vibration Machine EV103VT650VC Susb-2 机械冲击台 SE Shock Machine HSKT-10 温控型短路试验机 SE Thermostat Short-circuit Testing Machine BE-1000W 挤压试验机 SE Crush Machine BE V10A 电池充放电仪 SE Battery Charge and Discharge Machine CT V10A-A

4 第 4 页, 共 17 页 5. 检测地点环境条件 Place and Environmental Conditions of the test 地点 : 电池实验室温度 (20±5) 相对湿度 (40~70)%RH Place Temperature R.H. 6. 测试结论 (COCLUSIO) 测试项目 ITEM 样品编号 SAMPLE UMBER 执行标准 STADARD 结论 COCLUSIO 高度模拟 C1~C10 (Altitude simulation) 通过 (PASS) 温度试验 (Thermal test) 通过 (PASS) 振动 (Vibration) 通过 (PASS) 冲击 (Shock) 通过 (PASS) 外部短路 U38.3 (External short circuit) 通过 (PASS) 挤压 (Crush) C11~C15 通过 (PASS) 过度充电 (Overcharge) 强制放电 (Forced discharge) C16~C25 C26~C35 通过 (PASS) 说明 (otes): C1~C10: 为第一个充放电周期完全充电状态的电芯 ; Cells at first cycle in fully charged states; C11~C15: 为第一个充放电周期 50% 设计额定容量状态的电芯 ; Cells at first cycle at 50% of the design rated capacity; C16~C25: 为第一个充放电周期完全放电状态的电芯 ; Cells at first cycle in fully discharged states; C26~C35: 为 50 个充放电周期后完全放电状态的电芯 ; Cells after 50 cycles ending in fully discharged states.

5 第 5 页, 共 17 页 7. 测试方法 (TEST METHOD) 小型电芯或电池必须按顺序进行试验 T.1 至 T.5 试验 T.6 和 T.8 应使用未另外试验过的电芯或电池试验 T.7 可以使用原先在试验 T.1 至 T.5 中使用过的未损坏电池进行, 以便测试交替充电放电过的电池质量损失依照下式计算 : 质量损失 (%)= (M1-M2)/M1 *100 式中 M1 是实验前的质量,M2 是试验后的质量如质量损失不超过下表所列数值, 即视为无质量损失 Tests T.1 to T.5 shall be conducted in sequence on the same cell or battery. Tests T.6 and T.8 shall be conducted using not otherwise tested cells or batteries. Test T.7 may be conducted using undamaged batteries previously used in tests T.1 to T.5 for purposes of testing on cycled batteries. In order to quantify the mass loss, the following procedure is provided: Mass loss(%) = (M1-M2) / M1 100 Where M1 is the mass before the test and M2 is the mass after the test. When mass loss does not exceed the values in Table blow, it shall be considered as no mass loss. 电芯或电池质量 M Mass M of cell or battery 质量损失限值 Mass loss limit M<1 克 (g) 0.5% 1g M 75 克 (g) 0.2% M>75 克 (g) 0.1% T.1 高度模拟试验电芯和电池应在压力等于或低于 11.6 千帕和环境温度为 (20 ±5 ) 下存放至少 6 小时要求电芯和电池无渗漏无排气无解体无破裂无起火, 并且每个试验电芯或电池在试验后的开路电压不小于其在进行这一实验前电压的 90% 有关电压的要求不适用于完全放电状态的试验电芯和电池 T.1 Altitude simulation Test cells and batteries shall be stored at a pressure of 11.6 kpa or less for at least six hours at ambient temperature (20 ± 5 C). Cells and batteries meet this requirement if there is no leakage, no venting, no disassembly, no rupture and no fire and if the open circuit voltage of each test cell or battery after testing is not less than 90% of its voltage immediately prior to this procedure. The requirement relating to voltage is not applicable to test cells and batteries at fully discharged states. T.2 温度试验试验电芯和电池应先在试验温度等于 75 ±2 的条件下存放至少 6 小时, 接着再在试验温度等于 -40 ±2 的条件下存放至少 6 小时两个极端试验温度之间的最大时间间隔为 30 分钟此程序重复进行, 完成 10 次, 接着将所有试验电芯和电池在环境温度 (20 ±5 ) 下存放 24 小时对于大型电芯和电池, 暴露于极端试验温度的时间至少应为 12 小时要求电芯和电池无渗漏无排气无解体无破裂和无起火, 并且每个试验电芯或电池在试验后的开路电压不小于其在进行这一试验前电压的 90% 有关电压的要求不适用于完全放电状态的试验电芯和电池

6 第 6 页, 共 17 页 T.2 Thermal test Test cells and batteries are to be stored for at least six hours at a test temperature equal to 75 ± 2 C, followed by storage for at least six hours at a test temperature equal to - 40 ± 2 C. The maximum time interval between test temperature extremes is 30 minutes. This procedure is to be repeated until 10 total cycles are complete, after which all test cells and batteries are to be stored for 24 hours at ambient temperature (20 ± 5 C). For large cells and batteries the duration of exposure to the test temperature extremes should be at least 12 hours. Cells and batteries meet this requirement if there is no leakage, no venting, no disassembly, no rupture and no fire and if the open circuit voltage of each test cell or battery after testing is not less than 90% of its voltage immediately prior to this procedure. The requirement relating to voltage is not applicable to test cells and batteries at fully discharged states. T.3 振动电芯和电池紧固于振动机平台, 但不得造成电芯变形, 并能准确可靠地传播振动振动应是正弦波形, 对数扫描频率在 7Hz 和 200Hz 之间, 在回到 7Hz, 跨度为 15 分钟这一振动过程须对三个相互垂直的电芯安装方位的每一方向重复进行 12 次, 共为时 3 小时其中一个振动方向必须与端面垂直作对数式频率扫描, 对总质量不足 12 千克的电芯和电池 ( 电芯和小型电池 ), 和对 12 千克及更大的电池有所不同对电芯和小型电池 : 从 7Hz 开始, 保持 1g 的最大加速度, 直到频率达到 18Hz 然后将振幅保持在 0.8mm( 总位移 1.6mm), 并增加频率直到最大加速度达到 8g( 频率约为 50Hz) 将最大加速度保持在 8g 直到频率增加到 200Hz 对大型电池 : 从 7 赫兹开始保持 1gn 的峰值加速度直到频率达到 18 赫兹然后将振幅保持在 0.8 毫米 ( 总行程 1.6 毫米 ) 并增加频率直到最大加速度达到 2gn( 频率约为 25 赫兹 ) 将峰值加速度保持在 2gn 直到频率增加到 200 赫兹要求电芯和电池无渗漏无排气无解体无破裂和无起火, 并且每个试验电芯或电池在试验后的开路电压不小于其在进行这一试验前电压的 90% 有关电压的要求不适用于完全放电状态的试验电芯和电池 T.3 Vibration Cells and batteries are firmly secured to the platform of the vibration machine without distorting the cells in such a manner as to faithfully transmit the vibration. The vibration shall be a sinusoidal waveform with a logarithmic sweep between 7 Hz and 200 Hz and back to 7 Hz traversed in 15 minutes. This cycle shall be repeated 12 times for a total of 3 hours for each of three mutually perpendicular mounting positions of the cell. One of the directions of vibration must be perpendicular to the terminal face. The logarithmic frequency sweep shall differ for cells and batteries with a gross mass of not more than 12 kg (cells and small batteries), and for batteries with a gross mass of more than 12 kg (large batteries). For cells and small batteries: from 7 Hz a peak acceleration of 1 gn is maintained until 18 Hz is reached. The amplitude is then maintained at 0.8 mm (1.6 mm total excursion) and the frequency increased until a peak acceleration of 8 gn occurs (approximately 50 Hz).A peak acceleration of 8 gn is then maintained until the frequency is increased to 200 Hz. For large batteries: from 7 Hz to a peak acceleration of 1 gn is maintained until 18 Hz is reached. The amplitude is then maintained at 0.8 mm (1.6 mm total excursion) and the frequency increased until a peak acceleration of 2 gn occurs (approximately 25 Hz). A peak acceleration of 2 gn is then maintained until the frequency is increased to 200 Hz.

7 第 7 页, 共 17 页 Cells and batteries meet this requirement if there is no leakage, no venting, no disassembly, no rupture and no fire during the test and after the test and if the open circuit voltage of each test cell or battery directly after testing in its third perpendicular mounting position is not less than 90% of its voltage immediately prior to this procedure. The requirement relating to voltage is not applicable to test cells and batteries at fully discharged states. T.4 冲击试验电芯和电池用坚硬支架紧固在试验装置上, 支架支撑着每个试验电池的所有安装面每个电芯须经受最大加速度 150g 和脉冲持续时间 6 毫秒的半正弦波冲击另外, 大型电芯或许须经受最大加速度 50g 和脉冲持续时间 11 毫秒的半正弦波冲击电池须经受半正弦波冲击的峰值加速度取决于电池组的质量对小型电池的脉冲持续时间为 6 毫秒, 对大型电池的脉冲持续时间为 11ms. 下面的公式用于计算相应的最小峰值加速度每个电芯或电池须在三个相互垂直的安装方位的正方向经受三次冲击, 接着再反方向经受三次冲击, 总共经受 18 次冲击要求电芯和电池无渗漏无排气无解体无破裂和无起火, 并且每个试验电芯或电池在试验后的开路电压不小于其在进行这一试验前电压的 90% 有关电压的要求不适用于完全放电状态的试验电芯和电池 T.4 Shock Test cells and batteries shall be secured to the testing machine by means of a rigid mount which will support all mounting surfaces of each test battery. Each cell shall be subjected to a half-sine shock of peak acceleration of 150 gn and pulse duration of 6 milliseconds. Alternatively, large cells may be subjected to a half-sine shock of peak acceleration of 50 gn and pulse duration of 11 milliseconds. Each battery shall be subjected to a half-sine shock of peak acceleration depending on the mass of the battery. The pulse duration shall be 6 milliseconds for small batteries and 11 milliseconds for large batteries. The formulas below are provided to calculate the appropriate minimum peak accelerations. 电池 Battery 小型电池 Small batteries 大型电池 Large batteries 最小峰值加速度 Minimum peak acceleration 150 gn or result of formula Acceleration(gn)= mass* whichever is smaller 50 gn or result of formula Acceleration(gn)= mass* whichever is smaller * Mass is expressed in kilograms. 脉冲持续时间 Pulse duration 6ms 11 ms Each cell or battery shall be subjected to three shocks in the positive direction and to three shocks in the negative direction in each of three mutually perpendicular mounting positions of the cell or battery for a total of 18 shocks.

8 第 8 页, 共 17 页 Cells and batteries meet this requirement if there is no leakage, no venting, no disassembly, no rupture and no fire and if the open circuit voltage of each test cell or battery after testing is not less than 90% of its voltage immediately prior to this procedure. The requirement relating to voltage is not applicable to test cells and batteries at fully discharged states. T.5 外部短路在一定的时间内加热电芯或电池使其外壳达到 57 ± 4 均匀稳定的温度, 温升时间取决于电芯或电池的尺寸和外观, 并且被评估和记录如果这种评估记录不可行, 那么小型电芯或电池的暴露时间应至少持续 6 小时, 大型电芯或电池应至少持续 12 小时然后使电芯或电池在 57 ±4 下经受总外电阻小于 0.1 欧姆的短路条件这一短路条件应在电芯或电池外壳温度回到 57 ±4 后持续至少 1 小时, 或者大电池的温度下降至最大温升值的一半并保持低于此温度值短路和冷却期间应至少在环境温度下进行要求电芯和电池外壳温度不超过 170, 并且在试验过程中及试验后 6 小时内无解体, 无破裂, 无起火 T.5 External short circuit The cell or battery to be tested shall be shall be heated for a period of time necessary to reach a homogeneous stabilized temperature of 57 ± 4, measured on the external case. This period of time depends on the size and design of the cell or battery and should be assessed and documented. If this assessment is not feasible, the exposure time shall be at least 6 hours for small cells and small batteries, and 12 hours for large cells and large batteries. Then the cell or battery at 57 ± 4 shall be subjected to one short circuit condition with a total external resistance of less than 0.1 ohm. This short circuit condition is continued for at least one hour after the cell or battery external case temperature has returned to 57 ± 4, or in the case of the large batteries, has decreased by half of the maximum temperature increase observed during the test and remains below that value. The short circuit and cooling down phases shall be conducted at least at ambient temperature. Cells and batteries meet this requirement if their external temperature does not exceed 170 C and there is no disassembly, no rupture and no fire during the test and within six hours after the test. T.6 撞击 / 挤压撞击 ( 适用于直径不小于 18 毫米的圆柱形电芯 ) 试样电芯或组成电芯放在平坦光滑的表面上, 一根 316 型不锈钢棒横放在试样中心, 钢棒直径 15.8 毫米 ±0.1 毫米, 长度至少 6 厘米, 或电芯最长端的尺度, 取二者之长者将一块 9.1 千克 ±0.1 千克的重锤从 61±2.5 厘米高处跌落到钢棒和试样交叉处, 使用一个几乎没有摩擦的对落体重锤阻力最小的垂直轨道或管道加以控制垂直轨道或管道用于引导落锤沿水平支撑表面呈 90 度落下接受撞击的试样, 纵轴应与平坦表面平行并与横放在试样中心的直径 15.8±0.1 毫米弯曲表面的纵轴垂直每一试样只经受一次撞击 T.6 Impact / Crush Impact (applicable to cylindrical cells greater than 18 mm in diameter) The sample cell or component cell is to be placed on a flat smooth surface. A 15.8 mm ± 0.1mm diameter, at least 6 cm long, or the longest dimension of the cell, whichever is greater, Type 316 stainless steel bar is to be placed across the centre of the sample. A 9.1 kg ± 0.1 kg mass is to be dropped from a height of 61 ± 2.5 cm at the intersection of the bar and sample in a controlled manner using a near frictionless, vertical sliding track or channel with minimal drag on the falling mass. The vertical track or channel used to guide the falling mass shall be oriented 90 degrees from the horizontal supporting surface.

9 第 9 页, 共 17 页 The test sample is to be impacted with its longitudinal axis parallel to the flat surface and perpendicular to the longitudinal axis of the 15.8 mm ± 0.1mm diameter curved surface lying across the centre of the test sample. Each sample is to be subjected to only a single impact. 挤压 ( 棱柱形袋装硬币 / 纽扣电芯和直径小于 18 毫米的圆柱形电芯 ) 将电芯或组成电芯放在两个平面之间挤压, 挤压力度逐渐加大, 在第一个接触点上的速度大约为 1.5 厘米每秒挤压持续进行, 直到出现以下三种情况之一 : (a) 施加的力量达到 13K±0.78K; (b) 电芯的电压下降至少 100mV; (c) 电芯变形达到原始厚度的 50% 或以上一旦达到最大压力电压下降 100mV 或更多, 或电芯变形至少达原厚度的 50%, 即可解除压力棱柱形或袋装电芯应从最宽的一面施压纽扣 / 硬币形电芯应从其平坦表面施压圆柱形电芯应从与纵轴垂直的方向施压每个试样电芯或组成电芯只做一次挤压试验试样应继续观察 6 小时试验应使用之间未做过其他试验的电芯或组成电芯进行要求电芯或组成电芯外壳温度不超过 170, 并且在试验过程中及试验后 6 小时内无解体, 无起火 Crush (applicable to prismatic, pouch, coin/button cells and cylindrical cells not more than 18 mm in diameter) A cell or component cell is to be crushed between two flat surfaces. The crushing is to be gradual with a speed of approximately 1.5 cm/s at the first point of contact. The crushing is to be continued until the first of the three options below is reached. (a) The applied force reaches 13 k ± 0.78 k; (b) The voltage of the cell drops by at least 100 mv; or (c) The cell is deformed by 50% or more of its original thickness. Once the maximum pressure has been obtained, the voltage drops by 100 mv or more, or the cell is deformed by at least 50% of its original thickness, the pressure shall be released. A prismatic or pouch cell shall be crushed by applying the force to the widest side. A button/coin cell shall be crushed by applying the force on its flat surfaces. For cylindrical cells, the crush force shall be applied perpendicular to the longitudinal axis. Each test cell or component cell is to be subjected to one crush only. The test sample shall be observed for a further 6 h. The test shall be conducted using test cells or component cells that have not previously been subjected to other tests. Cells and component cells meet this requirement if their external temperature does not exceed 170 C and there is no disassembly and no fire during the test and within six hours after this test. T.7 过度充电充电电流必须是制造商建议的最大持续充电电流的两倍试验的最小电压如下 : (a) 制造商建议的充电电压不大于 18V 时, 试验的最小电压应是电池最大充电电压的两倍或 22V 两者中的较小者 ; (b) 制造商建议的充电电压大于 18V 时, 试验的最小电压应为最大充电电压的 1.2 倍试验应在环境温度下进行, 进行试验的时间应为 24 小时要求充电电池在试验过程中和试验后 7 天内无解体, 无起火 T.7 Overcharge

10 第 10 页, 共 17 页 The charge current shall be twice the manufacturer s recommended maximum continuous charge current. The minimum voltage of the test shall be as follows: (a) When the manufacturer s recommended charge voltage is not more than 18V, the minimum voltage of the test shall be the lesser of two times the maximum charge voltage of the battery or 22V. (b) When the manufacturer s recommended charge voltage is more than 18V, the minimum voltage of the test shall be 1.2 times the maximum charge voltage. Tests are to be conducted at ambient temperature; the duration of the test shall be 24 hours. Rechargeable batteries meet this requirement if there is no disassembly and no fire during the test and within seven days after the test. T.8 强制放电每个电芯应在环境温度下与 12V 直流电电源串联在起始电流等于制造商给定的最大放电电流的条件下强制放电将适当大小和额定值的电阻负荷与试验电池串联, 计算得出给定的放电电流对每个电池进行强制放电, 放电时间应等于其额定容量除以初始试验电流要求原电芯或充电电芯在试验过程中和试验后 7 天内无解体, 无起火 T.8 Forced discharge Each cell shall be forced discharged at ambient temperature by connecting it in series with a 12V D.C. power supply at an initial current equal to the maximum discharge current specified by the manufacturer. The specified discharge current is to be obtained by connecting a resistive load of the appropriate size and rating in series with the test cell. Each cell shall be forced discharged for a time interval (in hours) equal to its rated capacity divided by the initial test current (in ampere). Primary or rechargeable cells meet this requirement if there is no disassembly and no fire during the test and within seven days after the test.

11 第 11 页, 共 17 页 8. 测试程序 TEST PROCEDURE 编号分组 Marking 预处理 Pretreatment C1-C10 C11-C15 C16~C25 C26~C35 高度模拟 Altitude simulation 温度测试 Thermal test 振动 Vibration 挤压 Crush 过度充电 Overcharge 强制放电 Forced discharge 冲击 Shock 外部短路 External short circuit 数据处理 Analysis

12 第 12 页, 共 17 页 9. 测试数据 DATA T.1 高度模拟 (Altitude simulation) 电池编号 o. 测试前 Pre-test 测试后 After test 质量亏损 Mass loss (%) 质量 Mass 克 (g) 电压伏 (V) 质量 Mass 克 (g) 电压伏 (V) 电压亏损 loss (%) 有无渗漏, 排气, 解体, 破裂和起火 ( 是 / 否 ) Whether leakage, venting, disassembly, rupture, fire (Y/) C C C C C C C C C C T.2 温度测试 (Thermal test) 电池编号 o. 测试前 Pre-test 测试后 After test 质量亏损 Mass loss (%) 质量 Mass 克 (g) 电压伏 (V) 质量 Mass 克 (g) 电压伏 (V) 电压亏损 loss (%) 有无渗漏, 排气, 解体, 破裂和起火 ( 是 / 否 ) Whether leakage, venting, disassembly, rupture, fire (Y/) C C C C C C C C C C

13 第 13 页, 共 17 页 T.3 振动 (Vibration) 电池编号 o. 测试前 Pre-test 测试后 After test 质量亏损 Mass loss (%) 质量 Mass 克 (g) 电压伏 (V) 质量 Mass 克 (g) 电压伏 (V) 电压亏损 loss (%) 有无渗漏, 排气, 解体, 破裂和起火 ( 是 / 否 ) Whether leakage, venting, disassembly, rupture, fire (Y/) C C C C C C C C C C T.4 冲击 (Shock) 峰值加速度 :150 gn, 脉冲时间 :6ms: Peak acceleration: 150 gn, Pulse duration: 6 ms 电池编号 o. 测试前 Pre-test 测试后 After test 质量亏损 Mass loss (%) 质量 Mass 克 (g) 电压伏 (V) 质量 Mass 克 (g) 电压伏 (V) 电压亏损 loss (%) 有无渗漏, 排气, 解体, 破裂和起火 ( 是 / 否 ) Whether leakage, venting, disassembly, rupture, fire (Y/) C C C C C C C C C C

14 第 14 页, 共 17 页 T.5 外部短路 (External short circuit) 电池编号 o. 最高温度 Peak temperature ( ) 有无解体, 破裂, 起火 ( 是 / 否 ) Whether disassembly, rupture, fire (Y/) C C C C C C C C C C T.6 挤压 (Crush) 电池编号 o. 最高温度 Peak temperature ( ) 有无解体, 起火 ( 是 / 否 ) Whether disassembly, fire (Y/) C C C C C T.7 过度充电 (Overcharge) 电池编号 o. 有无解体, 起火 ( 是 / 否 ) Whether disassembly, fire (Y/)

15 第 15 页, 共 17 页 T.8 强制放电 (Forced discharge) 电池编号 o. 有无解体, 起火 ( 是 / 否 ) Whether disassembly, fire (Y/) C16 C17 C18 C19 C20 C21 C22 C23 C24 C25 C26 C27 C28 C29 C30 C31 C32 C33 C34 C35

16 第 16 页, 共 17 页 10. 样品照片 (Photos of the Sample) 电芯 (Cell)

17 第 17 页, 共 17 页声明 (DECLARATIO) 1. 测试参考文件 : 联合国关于危险货物运输的建议书试验和标准手册 (ST/SG/AC.10/11/Rev.6) United ations Recommendations On The Transport Of Dangerous Goods, Manual Of Tests And Criteria (ST/SG/AC.10/11/Rev.6). 2. 测试实验室 : Test place Lab: East of 4/F., Building A, Hourui o.3 Industrial Zone, Xixiang Street, Bao'an District, Shenzhen, 3. 本报告不能修改和删除 This report shall not be revised and deleted. 4. 本报告出现的试验结果仅与试验样品有关 The results only related to the items tested. 5. 本报告在未经书面许可情况下不能用于宣传广告之用 This report shall not be published as advertisement without the approval of Shenzhen Anbotek Compliance. 6. 除非全部复制, 否则无书面批准本报告不得部分复制 This report shall not be copied partly without the written approval of Shenzhen Anbotek Compliance. ********** 报告结束 ********** End of report

Microsoft Word - Lenovo_L15M3PB2 (Winbook)_3S1P_UN38.3 Test Report_SLEU

Microsoft Word - Lenovo_L15M3PB2 (Winbook)_3S1P_UN38.3 Test Report_SLEU Lithium-ion Battery UN38.3 Test Report Recommendations on the TRANSPORT OF DANGEROUS GOODS (Manual of Tests and Criteria, Fifth revised edition, Amend.2) Customer: Lenovo Model: L15M3PB2 Rating: 11.25V,