报告编号 Rep No. SET 检测报告 TEST REPORT 委托单位名称 Client Name 产品名称 Name of product 制造厂商 Manufacturer 商标型号 Trade mark & model 检测类别 Test sort 深圳市比苛电池有限

Size: px

Start display at page:

Download "报告编号 Rep No. SET 检测报告 TEST REPORT 委托单位名称 Client Name 产品名称 Name of product 制造厂商 Manufacturer 商标型号 Trade mark & model 检测类别 Test sort 深圳市比苛电池有限"

稳戚
4 years ago
Views:

检测报告 TEST REPORT 委托单位名称 Client Name 产品名称 Name product 制造厂商 Manufacturer 商标型号 Trade mark & model 检测类别 Test sort 深圳市比苛电池有限公司 Shenzhen PKCELL Battery Co.

1 检测报告 TEST REPORT 委托单位名称 Client Name 产品名称 Name product 制造厂商 Manufacturer 商标型号 Trade mark & model 检测类别 Test sort 深圳市比苛电池有限公司 Shenzhen PKCELL Battery Co.,Ltd 锂离子电池 Lithium-ion Battery 深圳市比苛电池有限公司 Shenzhen PKCELL Battery Co.,Ltd PKCELL/ ICR18650 Safety Entrust Test 中检集团南方电子产品测试 ( 深圳 ) 有限公司 CCIC Southern Electronic Product Testing (Shenzhen) Co., Ltd. 地址 : 广东省深圳市南山区西丽街道西丽工业区石鼓东栋邮政编码 /P.C.: Address: Building 28 29, Shigu east, Xili Factory District, Xili Road, Nanshan District, ShenZhen, Guangdong, China 电话 /TEL: 传真 /FAX: 网址 /Internet: 电子信箱 / sophie.wang@ccic-set.com 1

2 样品名称 Name sample 制造厂商 Manufacturer 委托单位 Client 送检日期 Application data 样品数量 Quantity samples 标称 Nominal voltage 3.7V 标准充电电流 Standard charge current (Battery/Power Bank) 中检集团南方电子产品测试 ( 深圳 ) 有限公司 CCIC Southern Electronic Product Testing (Shenzhen) CO., Ltd. 检测报告锂离子电池 Lithium-ion Battery TEST REPORT 深圳市比苛电池有限公司 Shenzhen PKCELL Battery Co.,Ltd 深圳市比苛电池有限公司 Shenzhen PKCELL Battery Co.,Ltd 440mA 放电终止 Cut-f 2.75V 检验项目 (Test item): 商标 Trade mark 型号规格 Model/Type 取样方式 Sampling method 2015/03/03 完成日期 Completing Date 43PCS Test1: 高度模拟 Altitude simulation Test2: 温度试验 Thermal Test Test3: 振动 Vibration Test4: 冲击 Shock 充电限制 Limited Charge 最大充电电流 Max. Charge Current (Battery/Power Bank) 最大放电电流 Max.Discharge Current Test5: 外短路 External short circuit Test6: 挤压 Crush Test7: 过充电 Overcharge Test8: 强制放电 Forced discharge 检测依据 (Reference documents): 检验环境 Environment condition 4.20V 2200mA 2200mA PKCELL ICR18650 Sent by client 2015/03/27 15~35 45~75%RH 额定能量 Rate Energy 充电截止电流 End Charge Current (Cell) 电池数量 Component cells Number 8.Wh/220 0mAh 44mA 1PCS 关于危险货物运输的建议书试验和标准手册 ( 五次修订版本 )38.3 节 : 金属锂电池和锂离子电池组 Recommendations on the Transport Dangerous Goods,Manual Test and Critera,section 38.3 lithium batteries(st/sg/ac.10/11/rev.5/amend.1section 38.3). 检验概况 (Summary): 对电池或电池组进行了 T1 至 T8 项试验, 试验 T1 至 T5 按顺序进行, 使用相同电池或电池组, 试验 T6 和 T8 使用未另外试验过的电池或电池组, 试验 T7 使用原先试验 T1 至 T5 中使用过的未损坏的电池组进行试验 Each Cell/battery type is subjectd to tests 1 to 8,Tests 1 to 5 are conducted in sequence on the same Cells/batteries,Tests 6 and 8 are conducted using not otherwise tested Cells/ batteries,test 7 using undamaged batteries previously used in Tests 1 to 5. 损失 loss%=(m1-m2)/m1 100 式中 :M1 是实验前的,M2 是试验后的, 如果损失不超过表所列的数值, 视为 2

3 无损失 Where M1 is the mass before the test and M2 is the mass after the test. When mass loss does not exceed the values in Table , it shall be considered as "no mass loss". M cell or battery loss limit M<1g 0.5% 1g M 75g 0.2% M>75g 0.1% 试验 T1 至 T4 如果电池组无渗漏无排气无解体无破裂和无起火, 并且每个试验电池组在试验后的开路不小于其在进行这一试验前的 90% 则认为符合要求 In test 1 to 4 batteries meet this requirement if there is no leakage,no venting, no disassembly, no rupture and no fire and if the open circuit voltage each test battery after testing is not less than 90% its voltage immediately prior to this procedure. 制造商提供的锂离子电池为单电芯电池, 根据标准规定, 单电芯电池应作为电池来评估, 按照电池的测试要求进行测试 The Lithium-ion Batteries submitted by manufacturer are single cell batteries,according to the standard,a single cell Battery is considered a Cell and shall be tested according to the testing requirements for cell. 备注 (Remark): 编号 B01#-B10# B16#-B19# 是在一个充放电周期完全充电的可充电电芯 ; Rechargeable cells B01#-B10# B16#-B19# are fully charge at first cycle; 编号 C11#-C15# 是在一个充放电周期 50% 设计额定容量状态的可充电电芯 ; Rechargeable cells C11#-C15# at 50% the design rated capacity at first cycle; 编号 B20#-B23# 是在 50 个充放电周期后完全充电的可充电电芯 ; Rechargeable cells B20#-B23# are fully charged after 50 cycles; 编号 C24#-C33# 是在一个充放电周期完全放电的可充电电芯 ; Rechargeable Cells B24#-B33# ard in fully Discharged at first cycle; 编号 C34#-C43# 是在 50 个充放电周期后完全放电的可充电电芯 ; Rechargeable cells B34#-B43# are in fully discharged after 50 cycles; 检验结论 (Test conclusion): 测试样品符合联合国关于危险货物运输的建议书试验和标准手册 38.3 要求 The test samples comply with section 38.3 Recommendations on the Transport Dangerous Goods,Manual Test and Critera. ( 检验单位盖章 stamp) 检测 : Tested by 审核 : Reviewed by 批准 : Approved by 2015 年 03 月 27 日 2015 年 03 月 27 日 2015 年 03 月 27 日 3

4 测试流程 Test Procedure 预处理 Pretreatment 标记 Marking 样品编号 Samples :B01#-B10# 样品编号 Samples :C11#-C15# 样品编号 Samples :B16#-B23# 样品编号 Samples :C24#-C43# 高度模拟 Altitude simulation 温度试验 Thermal test 振动 Vibration 挤压 Crush 过充 Overcharge 强制放电 Forced dischage 冲击 Shock 外短路 External short circuit 完成 Finished test 4

5 测试结果 Test results: Test T.1 高度模拟 Altitude siuiation 电池在压力等于或低于 11.6 千帕和环境温度 (20±5 ) 下存放至少 6 小时 Cells are stored at a pressure 11.6 kpa or less for at least six hours at ambient temperature (20±5 ). 电池如无渗漏无排气无解体无破裂和无燃烧, 并且每个试验电池在试验后的开路不小于其在进行这一试验前的 90%, 电池即符合这一要求 Cells meet this requirement if there is no leakage, no venting, no disassembly, no rupture and no fire and if the open circuit voltage each test cells after testing is not less than 90% its voltage immediately prior to this procedure. 测试数据如下表 Test Date showed in table below; 样品状态 State sample 一个充放电周期完全充电 At first cycle,in fully charged states 序号试验前 Pre-test 试验后 After test 损失 loss (%) 比 after test/ pre-test(%) Status B01# PASS B02# PASS B03# PASS B04# PASS B05# PASS B06# PASS B07# PASS B08# PASS B09# PASS B10# PASS 试验后电池无渗漏无排气无解体无破裂和无燃烧, 环境温度 22.5 After the test,the cells are no leakage,no venting, no disassembly, no rupture and no fire. Ambient temperature:

6 Test T.2: 温度试验 Thermal test 电池在试验温度等于 75±2 下存放至少 6 小时, 接着在试验温度等于 -40±2 下存放至少 6 小时两个极端试验温度之间的最大时间间隔为 30 分钟这一程序重复 10 次, 接着将所有试验电池在环境温度 ( 20±5 ) 下存放 24 小时 Cells are to be stored for at least six hours at a test temperature equal to 75 ± 2 C, followed by storage for at least six hours at a test temperature equal to - 40 ± 2 C. The maximum time interval between test temperature extremes is 30 minutes. This procedure is to be repeated 10 times, after which all test cells are to be stored for 24 hours at ambient temperature (20 ± 5 C). 电池如无渗漏无排气无解体无破裂和无燃烧, 并且每个试验电池在试验后的开路不小于其在进行这一试验前的 90%, 电池即符合这一要求 Cells meet this requirement if there is no leakage, no venting, no disassembly, no rupture and no fire and if the open circuit voltage each test cells after testing is not less than 90% its voltage immediately prior to this procedure. 测试数据如下表 Test Date showed in table below; 样品状态 State sample 一个充放电周期完全充电 At first cycle,in fully charged states 序号试验前 Pre-test 试验后 After test 损失 loss (%) 比 after test/ pre-test(%) Status B01# PASS B02# PASS B03# PASS B04# PASS B05# PASS B06# PASS B07# PASS B08# PASS B09# PASS B10# PASS 试验后电池无渗漏无排气无解体无破裂和无燃烧, 环境温度 22.7 After the test,the cells are no leakage,no venting, no disassembly, no rupture and no fire. Ambient temperature:

7 Test T.3: 振动 Vibration 电池紧固在振动机平面上, 正弦波形振动, 频率在 7 和 200 赫兹之间摆动再回到 7 赫兹的对数扫频为时 15 分钟这一振动过程须对三个互相垂直的电池安装方位的每一个方向都重复进行 12 次, 总共为时 3 小时其中一个振动方向必须与端面垂直对数扫频为 : 从 7 赫兹开始保持 1gn 的最大加速度直到频率达到 18 赫兹然后将振幅保持在 0.8 毫米 ( 总偏移 1.6 毫米 ) 并增加频率直到最大加速度达到 8gn( 频率约为 50 赫兹 ) 将最大加速度保持在 8gn 直到频率增加到 200 赫兹 Cells are firmly secured to the platform the vibration machine,the vibration is a sinusoidal waveform with a logarithmic sweep between 7 Hz and 200 Hz and back to 7 Hz traversed in 15 minutes. This cycle shall be repeated 12 times for a total 3 hours for each three mutually perpendicular mounting positions the cell. One the directions vibration must be perpendicular to the terminal face. The logarithmic frequency sweep is as follows: from 7 Hz a peak acceleration 1gn is maintained until 18 Hz is reached. The amplitude is then maintained at 0.8 mm (1.6 mm total excursion) and the frequency increased until a peak acceleration 8 gn occurs (approximately 50 Hz). A peak acceleration 8 gn is then maintained until the frequency is increased to 200 Hz. 电池如无渗漏无排气无解体无破裂和无燃烧, 并且每个试验电池在试验后的开路不小于其在进行这一试验前的 90%, 电池即符合这一要求 Cells meet this requirement if there is no leakage, no venting, no disassembly, no rupture and no fire and if the open circuit voltage each test cells after testing is not less than 90% its voltage immediately prior to this procedure. 测试数据如下表 Test Date showed in table below; 样品状态 State sample 一个充放电周期完全充电 At first cycle,in fully charged states 序号试验前 Pre-test 试验后 After test 损失 loss (%) 比 after test/ pre-test(%) Stat us B01# PASS B02# PASS B03# PASS B04# PASS B05# PASS B06# PASS B07# PASS B08# PASS B09# PASS B10# PASS 试验后电池无渗漏无排气无解体无破裂和无燃烧, 环境温度 22.6 After the test,the cells are no leakage,no venting, no disassembly, no rupture and no fire. Ambient temperature:

8 Test T.4: 冲击 Shock 电池用坚硬支架紧固在试验装置上, 支架支撑着每个试验电池的所有安装面每个电池经受最大加速度 150gn 和脉冲持续时间 6 毫秒的半正弦波冲击每个电池在三个互相垂直的电池组安装方位的正方向经受三次冲击, 接着在反方向经受三次冲击, 总共经受 18 次冲击 cells are secured to the testing machine by means a rigid mount which will support all mounting surfaces each test cell. Each cell is subjected to a half-sine shock peak acceleration 150 gn and pulse duration 6 milliseconds. Each battery is subjected to three shocks in the positive direction followed by three shocks in the negative direction three mutually perpendicular mounting positions the battery for a total 18 shocks. 电池如无渗漏无排气无解体无破裂和无燃烧, 并且每个试验电池在试验后的开路不小于其在进行这一试验前的 90%, 电池即符合这一要求 Cells meet this requirement if there is no leakage, no venting, no disassembly, no rupture and no fire and if the open circuit voltage each test cells after testing is not less than 90% its voltage immediately prior to this procedure. 测试数据如下表 Test Date showed in table below; 样品状态 State sample 一个充放电周期完全充电 At first cycle,in fully charged states 序号试验前 Pre-test 试验后 After test 损失 loss (%) 比 after test/ pre-test(%) Stat us B01# PASS B02# PASS B03# PASS B04# PASS B05# PASS B06# PASS B07# PASS B08# PASS B09# PASS B10# PASS 试验后电池无渗漏无排气无解体无破裂和无燃烧, 环境温度 24.3 After the test,the cells are no leakage,no venting, no disassembly, no rupture and no fire. Ambient temperature:

9 Test T.5: 外部短路 External short circuit 电池的温度稳定后使其外壳温度达到 55±2, 然后电池组在 55±2 下经受总外阻小于 0.1 欧姆的短路条件短路条件持续到电池外壳温度回到 55±2 后继续至少 1 小时, 再观察 6 小时结束试验 Cells be tested are temperature stabilized so that its external case temperature reaches 55±2 and then the cell are subjected to a short circuit condition with a total external resistance less than 0.1 ohm at 55±2. This short circuit condition is continued for at least one hour after the cell external case temperature has returned to 55±2. The cells are observed for a further six hours for the test to concluded. 外壳温度如不超过 170, 并且在试验过程后 6 小时内无解体无破裂无起火, 电池即符合这一要求 Cells meet this requirement if their external temperature does not exceed 170 and there is no disassembly, no rupture and no fire within six hours after test. 测试数据如下表 Test Date showed in table below; 样品状态 State sample 序号最高温度 Highest temperature( ) Status 一个充放电周期完全充电 At first cycle,in fully charged states B01# 55.9 PASS B02# 54.7 PASS B03# 55.3 PASS B04# 55.1 PASS B05# 55.6 PASS B06# 55.8 PASS B07# 54.6 PASS B08# 55.2 PASS B09# 55.7 PASS B10# 55.3 PASS. 试验后电池 6 小时内无解体无破裂无起火, 环境温度 24.6 After the test,the cells are no disassembly,no rupture and no fire within six hours. Ambient temperature:

10 Test T.6: 挤压 Crush 将电池放在两个平面之间挤压, 挤压力度逐渐加大, 在一个接触点上的速度大约为 1.5 厘米 / 秒, 直到出现下列的情况之一 ; Cells is to be crushed between two flat surfaces. The crushing is to be gradual with a speed approximately 1.5 cm/s at the first point contact,the crushing is to be continued until the first the three options below is reached. (a) 施加的力量达到 13 千牛 ±0.78 千牛 ; The applied force reaches 13 kn ± 0.78 kn; (b) 电池的下降至少 100mV; 或 The voltage the cell drops by at least 100 mv; or (c) 电池变形达原始高度的 50% 或以上 The cell is deformed by 50% or more its original thickness. 外壳温度如不超过 170, 并且在试验过程中及试验后 6 小时内无解体无破裂无起火, 电池即符合这一要求 Cells meet this requirement if their external temperature does not exceed 170 and there is no disassembly,no rupture and no fire during the test and within six hours after test. 测试数据如下表 Test Date showed in table below; 样品状态 State sample 一个充放电周期 50% 设计额定容量状态 At first cycle at 50% the design rated capacity 序号 Status C11# PASS C12# PASS C13# PASS C# PASS C15# PASS 电池在试验过程中和试验后 6 小时内无解体无破裂无起火, 环境温度 24.6 Cells are no disassembly and no fire during the test and within six hours after test. Ambient temperature:

11 Test T.7: 过充电 Overcharge 充电电流为制造商建议的最大持续充电电流的两倍, 试验为电池最大充电的两倍, 试验在环境温度下进行, 进行试验时间为 24 小时 The charge current is twice the manufacturer's recommended maximum continuous charge current. The voltage the test is the lesser two times the maximum charge voltage the battery,tests are to be conducted at ambient temperature. The duration the test is 24 hours. 电池如在试验过程中和试验后 7 天内无解体, 无起火, 即符合本项要求 Cells meet this requirement if there is no disassembly and no fire during the test and within seven days after the test 测试数据如下 Test Date showed in table below; 过充电流 Overcharge current: =4400mA 样品状态 State sample 一个充放电周期后完全充电 At first cycle in fully charged states 五十个充放电周期后, 完全充电 After 50 cycles ending in fully charged states 过充 Overcharge voltage : 2 3.7=7.4V 序号充电总时间 Total time charging: 24hours Status B16# PASS B17# PASS B18# PASS B19# PASS B20# PASS B21# PASS B22# PASS B23# PASS 电池在试验过程中和试验后 7 天内无解体无起火, 环境温度 24.5 Cells are no disassembly and no fire during the test and within seven days after the test Ambient temperature:

12 Test T.8: 强制放电 Forced discharge 电池在环境温度下与 12V 直流电电源串联在起始电流等于制造商给的的最大放电电流条件下强制放电 Each cells is forced discharged at ambient temperature by connecting it in series with a 12V D.C. power supply at an initial current equal to the maximum discharge current specified by the manufacturer. 充电电池如在试验过程中和试验后 7 天内无解体, 无起火, 即符合本项要求 Recharged cells meet this requirement if there is no disassembly and no fire during the test and within seven days after the test. 测试数据如下表 Test Date showed in table below; 样品状态序号 State sample Status C24# PASS C25# PASS C26# PASS 一个充放电周期后完全放电 At first cycle in fully discharged states C27# PASS C28# PASS C29# PASS C30# PASS C31# PASS C32# PASS C33# PASS C34# PASS C35# PASS C36# PASS 五十个充放电周期后, 完全放电 After 50 cycles ending in fully discharged states C37# PASS C38# PASS C39# PASS C40# PASS C41# PASS C42# PASS C43# PASS 试验后充电电池在试验过程中和试验后 7 天内无解体无起火, 环境温度 24.3 After the test,the recharged cells are no disassembly and no fire during the test and within seven days Ambient temperature:

13 样品照片 Photo document 图片 Photo 1 图片 Photo 2 13

14 声明 STATEMENT 1. 本实验室是经过中国合格评定国家认可委员会认可的检测实验室, 证书号 :L1659 This test laboratory is accredited by CNAS,Accreditation Certificate L 报告未加盖检测专用章无效 The test report is invalid without stamp laboratory. 3. 报告无检测批准人员签字无效 The test report is invalid without signature person(s) testing and authorizing. 4. 报告涂改无效 The test report is invalid if erased and corrected. 5. 自送样品的检测结论仅对送检样品有效 Test results the report is valid to the test samples if sampling by client. 6. CNAS 未涉及的项目 item cannot be Accredited by CNAS. 7. 未经本实验室书面同意, 不得部分地复制本报告 The test report shall not be reproduced except in full, without written approval the laboratory. 8. 如对本报告有异议, 可在收到报告后 15 天内向本单位申诉, 逾期不予受理 If there is any objection to report,the client should inform issuing laboratory within 15 days from the date receving test report. 地址 : 广东省深圳市南山区西丽街道西丽工业区石鼓东栋邮政编码 /P.C.: Address: Building 28 29, Shigu east, Xili Factory District, Xili Road, Nanshan District, ShenZhen, Guangdong, China 电话 /TEL: 传真 /FAX: 网址 /Internet: 电子信箱 / sophie.wang@ccic-set.com

Microsoft Word - Lenovo_L15M3PB2 (Winbook)_3S1P_UN38.3 Test Report_SLEU

Microsoft Word - Lenovo_L15M3PB2 (Winbook)_3S1P_UN38.3 Test Report_SLEU Lithium-ion Battery UN38.3 Test Report Recommendations on the TRANSPORT OF DANGEROUS GOODS (Manual of Tests and Criteria, Fifth revised edition, Amend.2) Customer: Lenovo Model: L15M3PB2 Rating: 11.25V,