KV-DA322M66

Transcription

1 () Trinitron Color TV Operating Instructions Before operating the unit, please read this manual thoroughly and retain it for future reference. GB CT Panduan Pengendalian Sebelum mengendalikan unit, sila baca buku panduan ini dengan teliti dan simpan untuk rujukan masa depan. MY KV-DA Sony Corporation M66

2 WARNING Dangerously high voltages are present inside the TV. TV operating voltage: V AC. Do not plug in the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground. To avoid battery leakage and damage to the remote, remove the batteries from the remote if you are not going to use it for several days. If any liquid leaks from the batteries and touches your skin, immediately wash it away with water. For your own safety, do not touch any part of the TV, the power cord and the antenna cable during lightning storms. For children s safety, do not leave children alone with the TV. Do not allow children to climb onto it. To prevent fire or shock hazard, do not expose the TV to rain or moisture. Do not place any objects on the TV. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. Do not operate the TV if any liquid or solid object falls into it. Have it checked immediately by qualified personnel only. Install the TV on a stable TV stand and floor which can support the TV set weight. Ensure that the TV stand surface is flat and its area is larger than the bottom area of the TV. Do not block the ventilation openings of the TV. Do not install the TV in a confined space, such as a bookcase or built-in cabinet. Your TV is recommended for home use only. Do not use the TV in any vehicle or where it may be subject to excessive dust, heat, moisture or vibrations. Do not plug in too many appliances to the same power socket. Do not damage the power cord. Do not open the cabinet and the rear cover of the TV as high voltages and other hazards are present inside the TV. Refer servicing and disposal of the TV to qualified personnel. Clean the TV with a dry and soft cloth. Do not use benzine, thinner, or any other chemicals to clean the TV. Do not attach anything (e.g., adhesive tape, cellophane tape, glue) on the painted cabinet of the TV. Do not scratch the picture tube. Pull the power cord out by the plug. Do not pull the power cord itself. Even if your TV is turned off, it is still connected to the AC power source (mains) as long as the power cord is plugged in. Unplug the TV before moving it or if you are not going to use it for several days. 2

3 Table of Contents Installation Securing the TV... 4 Getting Started... 5 Setting up your TV ( Initial Setup )... 6 Overview of Controls TV front and rear panels... 8 Using the remote control and basic functions... 9 Advanced Operations ing the picture and sound modes... Using the wide screen mode... 2 Enjoying the WEGA Theatre Mode with center speaker... 4 Viewing two programs at the same time... 5 Displaying multiple programs... 6 Enjoying stereo or bilingual programs... 7 Viewing Teletext... 8 Operating optional components... 9 Menu Adjustment Introducing the WEGA GATE navigator Settings Adjustment... 2 Changing the Picture setting Changing the Sound setting Changing the Wide Screen setting Changing the Multi Picture setting Changing the Channel Setup setting Changing the Setup setting... 3 Additional Information Connecting optional components Troubleshooting Specifications... Back cover GB 3

4 Installation x Securing the TV To prevent the TV from falling, use the supplied screws, clamps and band to secure the TV. 20 mm 3.8 mm screws clamps band Screw the band to the TV stand and to the provided hole at the rear of your TV. or () Put a cord or chain through the clamps. (2) Screw one clamp to a wall or pillar and the other clamp to the provided hole at the rear of your TV. or () Attach each end of a cord or chain to the provided holders at the rear of your TV. (2) Securely fix the attached cord or chain to a wall or pillar using an attachment which can support the TV set weight. Note Use only the supplied screws. Use of other screws may damage the TV. 4 Installation

5 Installation x Getting Started Step b Insert the batteries (supplied) into the remote. Note Do not use old or different types of batteries together. Step 2 Connect the antenna cable (not supplied) to 8 (antenna input) at the rear of the TV. Tip You can also connect your TV to other optional components (see page 33). Step 3 b Plug in the power cord, then press! on the TV to turn it on. Note The (standby) indicator flashes green for a few seconds when turning on the TV. This does not indicate a malfunction. Step 4 Set up the TV by following the instructions of the Initial Setup menu (see page 6). End Installation 5

6 x Setting up your TV ( Initial Setup ) When you turn on your TV for the first time, the Initial Setup menu will appear. You may change the menu language, preset the TV channels automatically, sort or edit the channels and adjust the picture position using the buttons on the remote control or TV front panel. Press V or v to select the desired menu language, then press. The selected menu language appears. End 2 Press V or v to select Yes, then press to preset the channels automatically. The screen will indicate automatic presetting is in progress. After all available channels have been tuned and stored, the Program Sorting/Edit menu appears automatically on the screen. To skip automatic channel presetting, select No, then press. Program: TV System: VHF Low End 0 Auto If the message No channel found. Please connect cable/antenna appears, check your TV connections, then press. End 3 The Program Sorting/Edit menu enables you to sort and edit the channels. a) If you wish to keep the channels in the current condition, press WEGA GATE to exit. b) Press V or v to select the program number with the channel you wish to change. The selected channel will appear on the screen. c) If you wish to store the channels in a different order: ) Press b to enter sorting mode. 2) Press V or v to select the new program number position for your selected channel, then press B. Program Sorting/Edit PROG Label Skip 0 Off 02 Off 03 Off 04 Off 05 Off Sorting: Edit: Program Sorting/Edit PROG Label Skip 0 Off 02 Off Off 05 Off Sorting mode Exit Off Exit 6 Installation

7 Installation d) If you wish to edit the channels, press to change to edit mode. Press b until the mode that you wish to edit is highlighted: Label, Skip, (block symbol). Then press. ) To label, press V or v to select the alphanumeric characters for the label. Then press. 05 Exit 2) To skip the program number, press V or v to select On. Then press. You can skip this program number when using PROG +/ ) To block unwanted program number, press V or v to select. Then press. Exit e) Repeat step b) to d) if you wish to change other channels. Press WEGA GATE to go to the next menu. Exit 4 Press B or b to adjust the bars on the top and bottom of the menu if they are slanted, then press. Picture V-Position menu appears. End 5 If the upper and lower bars are not equally positioned to the top and bottom of the screen, press V or v to adjust them, then press. End If no adjustment is necessary, then press. 6 To prevent this Initial Setup menu from appearing again when you turn on the TV by pressing!, press V or v to select No, then press. To allow this menu to appear again, select Yes, then press. Tip You can immediately go to the end of the Initial Setup menu by pressing WEGA GATE. Note Before adjusting Picture Rotation and Picture V-Position, keep external speakers or other electrical equipment away from the TV. The magnetic disturbance from these equipments or the direction of the earth s magnetic field may affect the TV. Installation 7

8 4 L(MONO) R AUTO PROG:Press [MENU] for 5sec SOUND MENU MODE (AUTO PROG) PROG Overview of Controls x TV front and rear panels TV rear panel R L Y PB/ CB PR/ CR C 2 20W MAX qa qs qd qf qg qh TV front panel ( ) WEGA GATE L(MONO) R Y PB/CB PR/CR SOUND MODE PROG Button/Terminal Function Page! Turn off or turn on the TV. 5 2 Standby indicator. 5 2 Wake Up indicator. 9 3 Remote control sensor. 4 PROG +/ program number / Adjust volume. 6 t TV or video input. 33 WEGA GATE menu operations 4, 5 V,v,B,b and adjust items selected items WEGA GATE Display or cancel WEGA GATE menu SOUND MODE sound mode options with a 5-Band Graphic Equalizer display. 9 t2 Video input terminal Component video input terminal i Headphone jack. qa Center speaker input terminal. 35 qs t, t3, t4 Video input terminal, 3, qd T Monitor output terminal. 34 qf 2 Component video input terminal qg Component video input terminal. 34 qh 8 Antenna input terminal Overview of Controls

9 Overview of Controls x Using the remote control and basic functions qf qg qh qj qk ql w; wa ws WEGA THEATRE RETURN VIDEO A/B PROG INDEX OPTION TV PROG WEGA GATE qa qs qd Button Description Page?/ Turn off temporarily or turn on the TV. 2 a Display the TV program. 3 t TV or video input. 33 Stereo/bilingual operations 4 A/B stereo/bilingual mode. 7 5 PROG INDEX Display all preset TV programs. 6 WEGA GATE menu operations 6 V, v, B, b and adjust items selected items WEGA GATE Display or cancel WEGA 20 GATE menu. qj RETURN Return to the previous level Change the picture size. 3 0 Jump to last program number that has been watched for at least five seconds. qa PROG +/ program number. Timer operations qs (Sleep Timer) qd (Wake Up Timer) Set TV to turn off automatically according to the desired period of time (max. of one hour and 30 min.). Set TV to turn on automatically according to the desired period of time (max. of 2 hours). The indicator on TV lights up amber once you set the wake up timer. If no buttons or controls are pressed for more than one hour after the TV is turned on using the wake up timer, the TV automatically goes into standby mode. qf Mute the sound. qg Display on-screen information. qh WEGA THEATRE WEGA Theatre Mode. 4 continue Overview of Controls 9

10 continued Button Description Page qk sound mode options with a 5-Band Graphic Equalizer display. ql picture mode options. w; surround mode options. 25 wa 0 9 Input numbers. For program numbers 0 and above, enter the second digit within two seconds. ws 2 +/ Adjust volume. TWIN picture operations,, V,v,B,b All buttons are used for Twin picture operations. 5 Teletext operations (green label),,,, All buttons are used for Teletext operations. 8,,,, (red, green, yellow, blue) Optional components operations VIDEO?/, OPTION, For details, see Operating optional components. 9 N, X, x,., >, %, 2 +/ WOW, TruSurround, SRS and symbol are trademarks of SRS Labs, Inc. WOW and TruSurround technologies are incorporated under license from SRS Labs, Inc. Licensed by BBE Sound, Inc. under USP , BBE and BBE symbol are trademarks of BBE Sound, Inc. 0 Overview of Controls

11 Advanced Operations x ing the picture and sound modes You can select picture and sound modes and adjust the setting to your preference in the Custom option. WEGA THEATRE RETURN VIDEO A/B PROG INDEX WEGA GATE ing the picture mode Press to select the desired picture mode. Vivid Standard Custom To view contrast and sharp pictures. normal pictures. the last adjusted picture setting from the Picture Adjustment option in the menu (see page 24) ing the sound mode Press (or SOUND MODE on the front panel) to select the desired sound mode. 5-Band Graphic Equalizer display will appear. Dynamic Dynamic To listen to dynamic and clear sound that emphasizes both the low and high tones k 3k 8k Standard Standard sound that emphasizes voice and high tones. Custom k 3k 8k Custom the last adjusted sound setting from the Sound Adjustment option in the menu (see page 26) k 3k 8k Advanced Operations

12 x Using the wide screen mode The wide screen mode feature allows you to watch the picture filling the 6:9 screen of the TV. Watching the picture in wide screen mode automatically Auto Wide The TV automatically selects optimum wide screen mode according to the signal input and displays the picture to fill the 6:9 screen. The examples in the table below show the settings preset at the factory; Auto Wide is set to On and 4:3 Default is set to Wide Zoom in the Wide Screen menu (see page 27). When receiving Auto Wide The picture changes to functions to select normal 4:3 aspect ratio picture with or without an ID- or WSS signal. letter box picture with an ID- or WSS signal. Wide Zoom* Zoom Black bands may appear on the top and bottom of the screen. squeezed picture with an ID- or WSS signal. Full 720p/080i format signal (HDTV 6:9 picture). Full An HDTV 6:9 picture is always displayed in Full mode. * When a normal 4:3 picture is received, Wide Zoom mode is automatically selected with the factory setting. You can display picture as it is without enlarging it ( Normal mode) if you set 4:3 Default in the Wide Screen menu to Normal (see page 27). Note The Auto Wide feature may not work correctly depending on the quality of signal. In this case, select the wide screen mode manually using the button (see page 3). 2 Advanced Operations

13 Watching the picture in wide screen mode manually Press repeatedly until the mode indication you want is displayed on the screen PROG Wide Zoom V Center: 00 Zoom V Center: 00 Normal Full OPTION TV Notes You can also select the wide screen mode manually using the menu (see page 27). When the wide screen mode is selected by pressing the button on the remote or using the menu, the Auto Wide feature does not work temporarily. The Auto Wide feature functions again when: you change a TV channel. you change the video input. the TV is turned off and on again. the signal format is changed. The 720p/080i format signal (HDTV 6:9 picture) is always displayed in Full mode. In Wide Zoom or Zoom mode, you can adjust the vertical position of the picture (V Center) by using remote control. While V Center: 00 in Wide Zoom or Zoom mode is displayed for three seconds, press V or v to adjust the vertical position, then press. Advanced Operations 3

14 x Enjoying the WEGA Theatre Mode with center speaker WEGA THEATRE 2 +/ The WEGA Theatre Mode enables you to enjoy the best picture, sound and surround effect of a cinema from a DVD source. You can use your TV speaker as the center speaker of your audio system for optimum vocal enhancement and control its sound volume from the remote of the TV. Setting up WEGA Theatre Mode WEGA THEATRE RETURN OPTION TV VIDEO 4 Advanced Operations A/B PROG INDEX PROG WEGA GATE. Connect the center speaker terminals of the amplifier to the center speaker input terminal on the TV (see page 35). 2. the proper video input and center speaker mode from WEGA Theatre Setup menu and turn on (main power) the connected equipment (see page 3). 3. See the table below. If the connected equipment is a Sony audio/video equipment, you can set up the remote to work with the connected equipment (see page 9). To switch to WEGA Theatre Mode Press adjust center 2 +/. speaker volume WEGA THEATRE. Be sure to aim the remote control at the TV set and connected equipment for about one second after the button is pressed. The connected equipment turns on automatically from standby mode and will start playing (only for Sony audio/video equipment). The Picture Mode and Sound Mode will switch automatically to Custom and you can adjust the setting to your personal preference (see pages 24 and 26). Notes Be sure to place your TV and connected Sony equipment adjacent to each other so that you can control both the TV and the connected equipment by using the TV s remote control at the same time (see page 9). The WEGA Theatre and center speaker modes are automatically cancelled when you change the input mode or turn the TV off and on again. When the TV is in the center speaker mode, you cannot use the Twin pictures feature, change the surround sound and the Intelligent Volume mode. Some Sony equipment might not respond properly when WEGA THEATRE button is pressed. In this case, use the equipment s own remote control. To use the TV s speakers as the center speaker, you can also display Center Speaker from Sound menu and select On (see page 25).

15 x Viewing two programs at the same time With the Twin pictures feature, you can display two different TV program or video input at the same time. 0 8 V/v/B/b VIDEO WEGA THEATRE A/B PROG INDEX WEGA RETURN GATE OPTION TV PROG To display Twin pictures Press. To cancel, press the button again. select a program number V or v. in the right picture swap the left and right pictures swap sound between the. B or b once. left and right pictures A symbol will appear to indicate which screen you are hearing. change the screen size of the Twin pictures Hold B to increase the left screen size. Hold b to increase the right screen size. Sound will swap automatically to the screen which is increasing in size. ing TV program from TV in WEGA GATE menu (see page 20) using PAP (Picture And Picture) You can select your desired TV program directly from the right picture by using V or v buttons.. Press V or v until the desired program appears on the right picture. 2. Press (or b) to display the right picture in full screen. Notes You cannot change the picture size or swap the two pictures in the PAP mode. HD (high-definition) and DVD input signals are not available in the right picture. If you swap HD and DVD input signals from the left picture, the function is not available or the signal will not be displayed properly. This does not indicate a malfunction. You cannot change the picture to a video input in the right picture. You can only display a video input in the right picture by swapping the video input from the left picture. The Twin pictures feature is not available when the TV is in the center speaker mode (see page 4) and you cannot set the TV to the center speaker mode while viewing the Twin pictures. You can only enjoy stereo sound from the left picture. For the T (monitor output) terminals, the video output signal will follow the left picture on the screen and the audio output signal will follow the sound from your TV speaker. Due to different video processors used, it is normal that the picture quality of the right picture might be slightly different from the left picture. Advanced Operations 5

16 x Displaying multiple programs The Program Index feature displays all tuned TV programs scrolling on the screen for direct selection. PROG INDEX V/v/ WEGA THEATRE VIDEO A/B PROG INDEX Press PROG INDEX. The current program is displayed on the left. The first tuned program is displayed on the bottom right of the screen, then frozen. It scrolls up and the next program appears on the bottom-right until all tuned programs appear one by one. WEGA RETURN GATE PROG 2 3 Press V or v until the program you want to view is displayed in the frame, then press. To return to scrolling, press V or v again. Press again to enlarge the selected program into the left frame. OPTION TV 4 Press PROG INDEX. The selected program is displayed in full screen ,, 0 8, 8 Note When displaying multiple programs, only the sound of the left picture is heard. 6 Advanced Operations

17 x Enjoying stereo or bilingual programs You can enjoy stereo sound or bilingual programs of NICAM and A2 stereo systems by using the A/B button. VIDEO When receiving a NICAM program WEGA THEATRE Broadcasting On-screen display (ed sound) A/B A/B PROG INDEX NICAM stereo NICAM (Stereo sound) t t Mono (Regular sound) WEGA RETURN GATE OPTION PROG NICAM bilingual NICAM monaural NICAM Main t NICAM Sub t Mono (Main sound) (Sub sound) (Regular sound) t NICAM Main (Main sound) t Stereo (Stereo sound) t t t Mono (Regular sound) Mono (Regular sound) Main (Main sound) t Sub (Sub sound) t When receiving an A2 program Broadcasting On-screen display (ed sound) A2 stereo TV A2 bilingual Note If the stereo sound is noisy when receiving a stereo program, select Mono. The sound becomes monaural but the noise is reduced. Advanced Operations 7

18 x Viewing Teletext Some TV stations broadcast an information service called Teletext which allows you to receive various information, such as stock market reports and news. You can use the buttons on the remote to view Teletext. (red, green, yellow, blue), VIDEO WEGA THEATRE A/B PROG INDEX WEGA RETURN GATE OPTION TV PROG To Do this display a Teletext Press. Each time you press, the page on the screen changes as follows: TV picture Teletext t Teletext and TV t TV. If there is no Teletext broadcast, 00 is displayed at the top left corner of the screen. check the contents Press. of a Teletext service An overview of the Teletext contents, including page numbers, appears on the screen. select a Teletext page Press the number buttons to enter the three-digit page number of the desired Teletext page. If you make a mistake, reenter the correct page number. To access the next or previous page, press or. hold (pause) a Press to display the symbol at Teletext display the top left corner of the screen. To resume normal Teletext viewing, press. reveal concealed Press. information (e.g., To conceal the information, press the an answer to a quiz) button again. enlarge the Teletext Press. Each time you press, the display Teletext display changes as follows: Enlarge upper half t Enlarge lower half t Normal size. stand by for a Teletext () Enter the Teletext page number that page while watching you want to refer to, then press. a TV program (2) When the page number is displayed, press to show the text. select a FASTEXT Press (red, green, yellow and blue) menu or the colored that corresponds to the desired menu or boxes page number. turn off Teletext Press a. Notes The FASTEXT feature can be used only when the FASTEXT broadcast is available. Teletext is automatically cancelled when there is no signal or the frequency of input signal is not within the proper range. 8 Advanced Operations

19 x Operating optional components You can use the supplied remote to operate Sony audio/video equipment. Setting up the remote to work with other connected equipment While keeping VIDEO?/ pressed, press the corresponding number button for the desired equipment (see the chart below). For example, to operate a Sony 8 mm VCR: VIDEO + 8 To control Hold down VIDEO?/ and press Audio System, x, 2 or 3 0,, 2, or 3 DVD, 2 or 3 4, 5 or 6 VTR (Beta), VTR2 (8 mm) or VTR3 (VHS) 7, 8 or 9 Operating audio/video equipment Press VIDEO?/ or while keeping OPTION pressed, press N, x,., >, X, or 2 +/ (see the chart below). To Press turn on/off VIDEO?/ play stop fast forward/ step forward or rewind/ step backward pause N while keeping OPTION pressed. x while keeping OPTION pressed. > or. while keeping OPTION pressed. X while keeping OPTION pressed. Press again to resume normal playback. mute the sound while keeping OPTION pressed. (Audio System, x, 2 or 3 only) adjust volume (Audio System, x, 2 or 3 only) 2 +/ while keeping OPTION pressed. Notes If the equipment does not have a certain function, the corresponding button on the remote will not operate. Some equipment might not respond properly to buttons on TV s remote. In this case, use the equipment s own remote control. Advanced Operations 9

20 Menu Adjustment x Introducing the WEGA GATE navigator WEGA GATE is a gateway that allows you access to preset TV channels, connected external inputs and Settings menu. WEGA GATE TV External Inputs Settings TV TV End watch the preset TV channels (see pages 6 and 5) External Inputs External Inputs End Video 2( ) Video 2 3 Video 3 4 Video 4 HD/DVD select the inputs for the connected equipment (see page 33) Settings Picture DRC-MF: DRC250 Picture Mode: Vivid Picture Adjustment 3D Intelligent Picture: On change the settings of your TV (see page 2) End How to use WEGA GATE WEGA GATE TV External Inputs Settings TV End () Press WEGA GATE to display or cancel the WEGA GATE menu. (3) Press V or v to select the desired item. TV End (2) Press (or b) to confirm your selection or go to the next level. WEGA GATE TV External Inputs Settings (4) Press RETURN to move to the previous level. Tip The WEGA GATE, operations above. and V,v,B,b buttons on the front panel can also be used for the 20 Menu Adjustment

21 x Settings Adjustment You are able to change the settings of your TV from Settings in WEGA GATE menu. Press WEGA GATE button to display WEGA GATE menu. Press V or v to select Settings and press. The following is an overview of the items that can be adjusted. Picture DRC-MF: DRC250 Picture Mode: Vivid Picture Adjustment 3D Intelligent Picture: On End Picture (see page 23) DRC-MF : DRC250 DRC00 Progressive Picture Mode : Vivid Standard Custom Picture Adjustment : Picture, Brightness, Color, Hue, Sharpness, Color Temperature, Reset 3D Intelligent Picture : On Off Sound Sound Mode: Dynamic Sound Adjustment Balance Intelligent Volume: Off Surround: Off Center Speaker: Off End Sound (see page 25) Sound Mode : Dynamic Standard Custom Sound Adjustment : Adjust, Reset Balance Intelligent Volume : On Off Surround : TruSurround WOW Simulated Off Center Speaker : On Off Wide Screen Wide Mode: Auto Wide: 4:3 Default: V Center: V Size: Wide Zoom On Wide Zoom End Wide Screen (see page 27) Wide Mode : Wide Zoom Normal Full Zoom Auto Wide : On Off 4:3 Default : Wide Zoom Normal V Center V Size Multi Picture Twin: Swap Program Index Off Multi Picture (see page 28) Twin : On Off Swap Program Index End continue Menu Adjustment 2

22 continued Channel Setup Auto Program Manual Program Program Sorting/Edit End Channel Setup (see page 29) Auto Program Manual Program Program : TV System : B/G I D/K M VHF Low / VHF High / UHF Fine : Auto Manual Signal Booster : Auto Off Program Sorting/Edit Setup Language: English Picture Position WEGA Theatre Setup Game Mode: Off Video Label Color System: Auto End Setup (see page 3) Language : English (Chinese) (Arabic) (Thai) Picture Position : Picture Rotation, Picture V-Position WEGA Theatre Setup : Direct Input, Speaker Game Mode : On Off Video Label Color System : Auto PAL SECAM NTSC3.58 NTSC4.43 Eco Mode : On Off Factory Settings : Yes No Note When a feature is dimmed in the menu, it is not selectable. 22 Menu Adjustment

23 x Changing the Picture setting 2 The Picture menu allows you to adjust the picture settings. Press WEGA GATE and select Settings. Make sure the Picture icon ( ) is selected, then press. Picture DRC-MF: DRC250 Picture Mode: Vivid Picture Adjustment 3D Intelligent Picture: On 3 Press V or v to select the desired item (e.g., DRC-MF ), then press. DRC-MF To choose either DRC250 (for high density pictures), DRC00 (reduce flicker on the screen) or Progressive (reduce jitter of any small areas or scanning lines on the screen). Picture Mode choose either Vivid, Standard or Custom * (see page ). 3D Intelligent Picture optimize picture quality. Automatically, the picture will become clearer and sharper if the signal is good and noise will be reduced if the signal is noisy. Press V or v to select On, then press. To cancel, select Off, then press. End * You can adjust the setting to your personal preference in the Picture Adjustment option only when the Custom mode is selected (see page 24). Notes The DRC-MF mode is not selectable when using the Program Index feature or when the Game Mode or Twin mode is turned On. The mode is not available for HD (highdefinition) and progressive input signals. 3D Intelligent Picture is not available in HD and progressive input signal. For NTSC 3.58 color system, 3D Comb Filter : On or 3D NR : On display will appear when 3D Intelligent Picture changes from one mode to the other. For PAL color system, Digital Comb Filter and 3D-NR are also available. The DRC-MF logo ( Corporation. ) and DRC-MF are trademarks of Sony continue Menu Adjustment 23

24 continued Adjusting the Picture Adjustment items under Custom mode 2 3 Press V or v to select either Picture (contrast), Brightness, Color, Hue (color tones), Sharpness or Color Temperature (choose either Cool, Neutral or Warm ), then press. ing Reset will set your TV to the factory settings. Press V,v,B or b to adjust the setting of your selected item, then press. Repeat the above steps to adjust other items. The adjusted settings will be received when you select Custom. Notes Hue can be adjusted for the NTSC color system only. Reducing Sharpness can also reduce picture noise. 24 Menu Adjustment

25 x Changing the Sound setting 2 The Sound menu allows you to adjust the sound settings. Press WEGA GATE and select Settings. Press V or v to select the Sound icon ( ), then press. Sound Sound Mode: Dynamic Sound Adjustment Balance Intelligent Volume: Off Surround: Off Center Speaker: Off 3 Press V or v to select the desired item (e.g., Sound Mode ), then press. Sound Mode Balance Intelligent Volume To choose either Dynamic, Standard or Custom * (see page ). Press v or B to emphasize the left speaker. Press V or b to emphasize the right speaker. adjust the volume of all program numbers and video inputs automatically. Press V or v to select On, then press. To cancel, select Off, then press. End Surround Center Speaker choose either TruSurround (surround sound that spreads out to the rear of a room), WOW ** (full, deep bass sound), Simulated (stereo-like monaural sound) or Off. use your TV speaker to optimise vocal enhancement. Press V or v to select On, then press. To cancel, select Off, then press. * You can adjust the setting to your personal preference in the Sound Adjustment option only when the Custom mode is selected (see page 26). ** BBE High Definition Sound is fully activated maximizing the sound effect in the WOW mode. Note Intelligent Volume is not selectable when TruSurround is selected. continue Menu Adjustment 25

26 continued Adjusting the Sound Adjustment items under Custom mode The 5-Band Graphic Equalizer feature allows you to adjust sound frequency settings of Custom mode in the menu. Make sure that Adjust is selected, then press. ing Reset will set your TV to the factory settings. Sound Adjustment Adjust Reset k 3k 8k 2 Press B or b to select the desired sound frequency, then press V or v to adjust the setting and press. The adjusted settings will be received when you select Custom. End Notes Adjusting higher frequency will affect higher pitched sound and adjusting lower frequency will affect lower pitched sound. You may display the settings directly by using the SOUND MODE button on the TV front panel (see page 8) or button on the remote control (see page 0). 26 Menu Adjustment

27 x Changing the Wide Screen setting 2 The Wide Screen menu allows you to watch the picture filling the 6:9 screen of the TV. Press WEGA GATE and select Settings. Press V or v to select the Wide Screen icon ( ), then press. Wide Screen Wide Mode: Auto Wide: 4:3 Default: V Center: V Size: Wide Zoom On Wide Zoom Press V or v to select the desired item (e.g., Wide Mode ), then press. Wide Mode To select the desired wide screen mode to fit the 6:9 screen. Press V or v to select Wide Zoom, Normal, Full or Zoom, then press. End Auto Wide automatically display the picture in optimum wide screen mode. Press V or v to select On, then press. Off if you want to display any picture in currently selected wide screen mode. 4:3 Default display a 4:3 picture in Wide Zoom or Normal mode. Press V or v to select the Wide Zoom or Normal, then press. V Center adjust the vertical position of the picture in Wide Zoom or Zoom mode. Press V or v to move the picture, then press. V Size adjust the vertical size of the picture in Wide Zoom or Zoom mode. Press V or v to adjust the vertical size, then press. Tips You can also change to wide-mode picture size by pressing the button on the remote control (see page 3). You can also adjust V Center by using remote control (see page 3). Notes Wide Mode will switch to 6:9 or 4:3 in the left screen when viewing twin pictures. Wide Mode is not selectable for HD (080i, 720p) input signals. For HD (080i, 720p) input signals, your TV will always display Full mode picture. Auto Wide is only available when receiving 576i, 480p and 480i input signals. 4:3 Default does not function when Auto Wide is set to Off. Menu Adjustment 27

28 x Changing the Multi Picture setting 2 The Multi Picture menu allows you to view two pictures on the screen at the same time, swap the picture of twin screen and display Program Index. Press WEGA GATE and select Settings. Press V or v to select the Multi Picture icon ( ), then press. Multi Picture Twin: Swap Program Index Off 3 Press V or v to select the desired item (e.g., Twin ), then press. Twin To display a different TV program beside the main picture. Press V or v to select On, then press. To cancel, select Off, then press. End Swap Program Index swap the left and right pictures of the twin screen. view multiple programs on the sub-screens. To cancel, select Program Index, then press. Tip You can also display or cancel the settings directly by pressing the, or PROG INDEX buttons on the remote control (see pages 5 and 6). 28 Menu Adjustment

29 x Changing the Channel Setup setting 2 The Channel Setup menu allows you to preset channels automatically, manually preset channels and sort or edit the channels. Press WEGA GATE and select Settings. Press V or v to select the Channel Setup icon ( ), then press. Channel Setup Auto Program Manual Program Program Sorting/Edit 3 Press V or v to select the desired item (e.g., Auto Program ), then press. Auto Program Manual Program Program Sorting/Edit To preset channels automatically. manually preset desired channels and channels that cannot be preset automatically (see Presetting channels manually in page 30). change the order in which the channels appear on the screen, label the program number, skip the program number and block unwanted programs. (see step 3 of the section Initial Setup in page 6). End Notes If you preset a blocked program number, that program number will be unblocked automatically. If you sort a blocked program, that program will remain blocked. continue Menu Adjustment 29

30 continued Presetting channels manually After selecting Manual Program, select the program number to which you want to preset a channel. () Make sure Program is selected, then press. (2) Press V or v until the program number you want to preset appears on the menu, then press. the desired channel. () Make sure either VHF Low, VHF High or UHF is selected, then press. (2) Press V or v until the desired channel s broadcast appears on the TV screen, then press. If the sound of the desired channel is abnormal, select the appropriate TV system. () Press V or v to select TV System, then press. (2) Press V or v until the sound becomes normal, then press. If you are not satisfied with the picture and sound quality, you may be able to improve them by using the Fine tuning feature. () Press V or v to select Fine, then press. (2) Press V or v to select Manual, then press. (3) Press V,v,B or b until the picture and sound quality are optimal, then press. The + or icon on the menu flashes while tuning. Manual Program Program: 0 TV System: B/G VHF Low Fine: Auto Signal Booster: Auto If the TV signal is too strong (picture distorted; picture with lines; signal interference) or weak (snowy picture), you may be able to improve the picture quality by setting the Signal Booster feature. () Press V or v to select Signal Booster, then press. (2) Press V or v to select Off (for picture distorted; picture with lines; signal interference) or Auto (for snowy picture), then press. End 30 Menu Adjustment

31 x Changing the Setup setting 2 The Setup menu allows you to change the menu language, adjust the picture position, setup WEGA Theatre Mode, adjust suitable picture setting for video games, label the connected equipment, select the color system, reduce your TV power consumption and reset your TV to factory settings. Press WEGA GATE and select Settings. Press V or v to select the Setup icon ( ), then press. Setup Language: English Picture Position WEGA Theatre Setup Game Mode: Off Video Label Color System: Auto 3 Press V or v to select the desired item (e.g., Language ), then press. Language To change the menu language. Press V or v to select either English, (Chinese), (Arabic) or (Thai), then press. End Picture Position WEGA Theatre Setup Game Mode adjust the picture position when it is not aligned with the TV screen. Press V or v to select Picture Rotation or Picture V-Position, then press. Press V,v,B or b to adjust the picture position, then press. setup WEGA Theatre Mode for best picture, sound and surround effect enjoyment of a cinema (see page 4). Press V or v to select Direct Input, then press. either Video, Video 2, Video 3, Video 4, HD/DVD or HD/DVD 2 for the connected equipment that you want to view with WEGA Theatre, then press. Speaker and press. Normally select MAIN. When you want to use the TV s speakers as the center speaker, press V or v to select CENTER IN, then press. adjust the picture setting that is suitable to view video games. Press V or v to select On, then press. To cancel, select Off, then press. continue Menu Adjustment 3

32 continued Video Label Color System Eco Mode To label the connected equipment. () Press V or v to select the input you want to label, then press. (2) Press V or v to select the label options: Video / Video 2 / Video 3 / Video 4 / HD/DVD / HD/DVD 2, VCR, SAT, Game or Edit *, then press. * You may edit the video label to your favorite name. Press V or v to select alphanumeric characters for the label, then press. select the color system. Press V or v to select either Auto, PAL, SECAM, NTSC3.58 or NTSC4.43, then press. Normally, set this to Auto. reduce power consumption of your TV to save energy. Press V or v to select On, then press. When you press or turn on the TV, Eco Mode ( ) symbol will appear on the screen for a while. To cancel, select Off, then press. Factory Settings reset your TV to factory settings. Press and press V or v to select Yes, then press. To cancel, select No, then press. Notes Your TV is over scanned to avoid the display of non picture related signals that may appear as distortions at the top or bottom of the screen due to the influence of the earth s magnetic field. This does not indicate a malfunction. If necessary, you can adjust the Picture V-Position or Picture Rotation to prevent seeing the display of this non picture related signals. You cannot adjust Picture Rotation and Picture V-Position when high-definition (080i, 720p) signals are input. Game Mode is available only when receiving signals through the t (video input), (S video input) or (component video input) terminals. When HD (high-definition) or progressive signals are input, Game Mode does not function. 32 Menu Adjustment

33 Additional Information x Connecting optional components Connecting to the video input terminal ( t ) or component video input terminal ( ) TV front panel 2 ( ) Y PB/CB PR/CR L(MONO) R Audio/ Video cable (not supplied) L R Camcorder or TV front panel 2 ( ) Component video cable (not supplied) Y PB/ CB PR/ CR L L(MONO) R R Y PB/CB PR/CR Audio cable (not supplied) HD Camcorder TV rear panel R L Y PB/ CB PR/ CR 20W MAX 8 C 2 Antenna cable (not supplied) 3 4 Audio/Video cable (not supplied) S Video cable (not supplied) Notes You can only connect to either video input signal (, L, R) or component video input signal (Y, PB/CB, PR/CR, L, R) on the front input terminal (t2 ( )) at one time. If you connect a VCR to 8 (antenna input), preset the signal output from the VCR to the program number 0 on the TV (see page 30). When both (S video) and (video) for t are connected at the same time, (S video) is automatically selected. To view (video), disconnect the S video cable. continue L R VCR DVD Player Additional Information 33

34 continued Connecting to the monitor output terminal ( T ) TV rear panel R L Y PB/ CB PR/ CR C 2 20W MAX L R Audio system Audio/ Video cable (not supplied) VCR Connecting to the component video input terminal ( ) TV rear panel 20W MAX 8 C R L PB/ PR/ Y CB CR Component video cable (not supplied) Y PB/ CB / PR CR L R DVD player Audio cable (not supplied) Digital TV receiver Notes The component video terminals on your DVD player are sometimes labeled Y/CB/CR, Y/PB/ PR, Y/Cb/Cr or Y/B-Y/R-Y. If you select HD/DVD or HD/DVD 2 on your TV screen, the signal from the T (monitor output) terminals will not be output properly. This does not indicate a malfunction. Tip The TV accepts the following signal formats: Total scanning line Effective scanning line fv (Hz) 25i 080i 50/60 750p 720p 50/60 625p 576p i 576i p 480p i 480i Additional Information

35 Connecting an amplifier to the center speaker input terminal ( ) If you use an amplifier with a Dolby* surround decoder instead of the TV s audio system, you can use the TV s speakers as the center speaker for your audio system. Using the speaker cords supplied with the amplifier, connect the center speaker terminals of the amplifier to the (center speaker input) terminals on the TV. TV rear panel Component video cable (not supplied) DVD player R L PB/ PR/ Y CB CR C Y 20W MAX 8 20W MAX 8 C 3 4 Audio cable (not supplied) PB/ CB PR/ CR L R Optical digital cable (not supplied) Amplifier Front speaker (L) Rear speaker (L) Front speaker (R) Rear speaker (R) Woofer Note If you use the TV s speakers as the center speaker and nothing is connected to the center speaker input terminals on the rear of TV or the sound source emitted from the amplifier does not contain the center speaker channel, no sound will be heard from the TV s speaker. * Dolby is a trademark of Dolby Laboratories. Additional Information 35

36 x Troubleshooting If you find any problem while viewing your TV, you can either use the Factory Settings function or check the Troubleshooting guide below. If the problem persists, contact your Sony dealer. Factory Settings function Press the WEGA GATE button. Choose Settings and go to Setup ( ) menu. From Setup menu, select Factory Settings. Then select Yes and press. Your TV will go blank for a few seconds, then the Initial Setup menu will appear. Your TV will be set to factory settings, but certain problems may be solved. Symptom Snowy picture, noisy sound Distorted picture, noisy sound Good picture, noisy sound No picture, no sound Good picture, no sound Dotted lines or stripes Double images or ghosts Solutions Check the antenna cable and connection on the TV, VCR and at the wall (see page 33). Check the antenna setup. Contact a Sony dealer for advice. Display the Channel Setup menu and select Manual Program to preset the channel again (see page 30). Display the Channel Setup menu and set the Signal Booster to Auto from Manual Program (see page 30). Try using an external booster. Turn off or disconnect the external booster if it is in use. Display the Channel Setup menu and set the Signal Booster to Off from Manual Program (see page 30). Display the Channel Setup menu and select the appropriate TV System from Manual Program (see page 30). The sound of the right picture is selected when twin pictures are displayed. Press or B, b once (see page 5). Check the power cord, antenna and VCR connections (see page 33). Press?/ (power) to turn on the TV (see page 9). Press! (main power) on the TV to turn off the TV for about five seconds, then turn it on again (see page 8). Press 2 + to increase the volume level (see page 0). Press to cancel the muting (see page 9). The sound of the right picture is selected when twin pictures are displayed. Press or B, b once (see page 5). Display the Sound menu and select the appropriate setting for Center Speaker (see page 25). Do not use a hair dryer or other equipment near the TV. Check the antenna setup. Contact a Sony dealer for advice. Use the fine tuning ( Fine ) function (see page 30). Check the antenna setup. Contact a Sony dealer for advice. Turn off or disconnect the external booster if it is in use. 36 Additional Information

37 Symptom No color Picture slant Abnormal color patches TV cannot receive stereo broadcast sound. or Solutions Display the Picture menu and select Custom from Picture Mode, then adjust the Color level from Picture Adjustment (see page 24). Display the Setup menu and check the Color System setting (usually set this to Auto ) (see page 32). Check the antenna setup. Contact a Sony dealer for advice. Keep external speakers or other electrical equipment away from the TV. Display the Picture Position under Setup menu, then adjust Picture Rotation and Picture V-Position so that the picture is aligned to the TV screen (see page 3). Keep external speakers or other equipment away from the TV. Do not move the TV while the TV is turned on. Press! (main power) on the TV to turn off the TV for about 5 minutes, then turn it on again to demagnetize the TV. Check the antenna cable and connection on the TV, VCR and at the wall (see page 33). Check the antenna setup. Contact a Sony dealer for advice. Stereo broadcast sound switches on and off or is distorted. Teletext display is incomplete (snowy picture or double images). Check the antenna cable and connection on the TV, VCR and at the wall (see page 33). Check the antenna setup. Contact a Sony dealer for advice. Display the Channel Setup menu and set the Signal Booster to Auto from Manual Program (see page 30). Use the fine tuning ( Fine ) function (see page 30). The wide screen mode changes spontaneously when Auto Wide is On. During a transition between two programs, the TV detects the optimum wide screen mode. During this period, an irregular wide screen mode may appear. The wide screen mode is switched automatically according to the received signal with an ID- or WSS signal. The Auto Wide feature stops working temporarily when you have pressed, and functions again when the signal format changes. To fix in the manually selected wide screen mode, set Auto Wide to Off in the Wide Screen menu (see page 27). The (standby) indicator on your TV flashes red several times after every three seconds. Count the number of times the (standby) indicator flashes. Press! (main power) to turn off your TV. Contact your nearest Sony service center. continue Additional Information 37

38 continued Symptom The TV screen sometimes goes blank for slightly longer than usual during channel change. Cannot play shooting games. TV cabinet creaks. A small boom sound is heard when the TV is turned on. Thin lines appear on the TV Screen. Solutions The Signal Booster is functioning to detect a weak signal. This does not indicate a malfunction. Some shooting games which involve pointing a light beam at the TV screen with an electronic gun or rifle cannot be used with your TV. For details, see the instruction manual supplied with the video game software. Changes in room temperature sometimes make the TV cabinet expand or contract, causing a noise. This does not indicate a malfunction. The TV s demagnetizing function is working. This does not indicate a malfunction. The visible lines that sometimes appear on your TV screen are shadows from the damper wires used to stabilize the aperture grille of the Trinitron picture tube. This does not indicate a malfunction. 38 Additional Information

39

40 WEGA MENU WEGA GATE CT 3

41 x

42 x b b! 4 Initial Setup 6 End 5

43 x Initial Setup V v 2 V v 0 3 a) WEGA GATE b) V v PROG c) ) b 2) V v B PROG

44 d) b ) V v 2) V v PROG +/ 3) V v e) b) d) WEGA GATE B b 5 V v 6! V v WEGA GATE 7

45 4 L(MONO) R AUTO PROG:Press [MENU] for 5sec SOUND MENU MODE (AUTO PROG) PROG x R L Y PB/ CB PR/ CR C 2 20W MAX qa qs qd qf qg qh ( ) WEGA GATE Y PB/CB PR/CR L(MONO) R SOUND MODE PROG! PROG +/ 5 2 +/ 6 t 33 WEGA GATE 4, 5 V,v,B,b WEGA GATE WEGA GATE 20 8 SOUND MODE 5-Band Graphic Equalizer 9 t DVD 33 0 i qa 35 qs t, t3, t4, 3, 4 33 qd T 34 qf 2 DVD 2 34 qg DVD 34 qh

46 x qf qg qh qj qk ql w; wa ws VIDEO WEGA THEATRE A/B PROG INDEX WEGA RETURN GATE OPTION TV PROG qa qs qd? 2 a 3 t 33 4 A/B 7 5 PROG INDEX 6 WEGA GATE 6 V, v, B, b WEGA WEGA GATE 20 GATE qj RETURN qa PROG +/ qs 30 qd 2 qf qg qh WEGA WEGA 4 THEATRE 9

47 qk 5-Band Graphic Equalizer ql w; 25 wa ws 2 +/,, V,v,B,b 5,,,, 8,,,, VIDEO?, OPTION, 9 N, X, x,., >, %, 2 +/ WOW, TruSurround, SRS SRS Labs, Inc. WOW TruSurround SRS Labs, Inc. BBE , BBE BBE BBE 0

48 x WEGA THEATRE VIDEO A/B PROG INDEX RETURN WEGA GATE SOUND MODE 5-Band Graphic Equalizer k 3k 8k k 3k 8k k 3k 8k

49 x 6:9 6:9 4:3 27 ID- WSS * ID- WSS ID- WSS 6:9 720p/080i HDTV 6:9 6:9 HDTV 6:9 6:9 4:3 4:3 4:3 4:

50 PROG OPTION TV p/080i HDTV 6:9 6:9 00 V v 3

51 x WEGA WEGA DVD WEGA THEATRE 2 +/ VIDEO WEGA THEATRE A/B PROG INDEX WEGA RETURN GATE OPTION TV PROG WEGA WEGA 3 3. Sony 9 WEGA 2 +/. WEGA THEATRE Sony Sony 9 WEGA WEGA THEATRE Sony 25 4

52 x 0 8 V/v/B/b VIDEO WEGA THEATRE A/B PROG INDEX WEGA RETURN GATE PROG V v B b B b OPTION TV WEGA GATE 20 PAP V v. V v 2. b PAP HD DVD HD DVD 4 T 5

53 x WEGA THEATRE VIDEO PROG INDEX PROG INDEX A/B PROG INDEX V/v/ RETURN WEGA GATE 2 V v V v PROG 3 4 PROG INDEX OPTION TV ,,, 8 6

54 x A/B NICAM A2 VIDEO WEGA THEATRE t A/B A/B PROG INDEX t t t RETURN WEGA GATE t t t PROG OPTION TV t t t A2 A2 t A2 7