KV-AZ21M61

Transcription

1 () Trinitron Color TV Operating Instructions Before operating the unit, please read this manual thoroughly and retain it for future reference. Panduan Pengendalian Sebelum mengendalikan unit, sila baca buku panduan ini dengan teliti dan simpan untuk rujukan masa depan. GB CT MY KV-AZ 005 Sony Corporation M6

2 WARNING Dangerously high voltages are present inside the TV. TV operating voltage: 0 40 V AC. Do not plug in the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground. To avoid battery leakage and damage to the remote, remove the batteries from the remote if you are not going to use it for several days. If any liquid leaks from the batteries and touches your skin, immediately wash it away with water. For your own safety, do not touch any part of the TV, the power cord and the antenna cable during lightning storms. For children s safety, do not leave children alone with the TV. Do not allow children to climb onto it. To prevent fire or shock hazard, do not expose the TV to rain or moisture. Do not place any objects on the TV. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. Do not operate the TV if any liquid or solid object falls into it. Have it checked immediately by qualified personnel only. Install the TV on a stable TV stand and floor which can support the TV set weight. Ensure that the TV stand surface is flat and its area is larger than the bottom area of the TV. Do not block the ventilation openings of the TV. Do not install the TV in a confined space, such as a bookcase or built-in cabinet. Your TV is recommended for home use only. Do not use the TV in any vehicle or where it may be subject to excessive dust, heat, moisture or vibrations. Do not plug in too many appliances to the same power socket. Do not damage the power cord. Do not open the cabinet and the rear cover of the TV as high voltages and other hazards are present inside the TV. Refer servicing and disposal of the TV to qualified personnel. Clean the TV with a dry and soft cloth. Do not use benzine, thinner, or any other chemicals to clean the TV. Do not attach anything (e.g., adhesive tape, cellophane tape, glue) on the painted cabinet of the TV. Do not scratch the picture tube. Pull the power cord out by the plug. Do not pull the power cord itself. Even if your TV is turned off, it is still connected to the AC power source (mains) as long as the power cord is plugged in. Unplug the TV before moving it or if you are not going to use it for several days.

3 Table of Contents Securing the TV... 4 Getting Started... 4 Setting up your TV ( Initial Setup )... 5 TV top control, front and rear panels... 7 Connecting optional components... 8 Using the remote control and basic functions... 0 Introducing the WEGA GATE navigator... Settings Adjustment... 3 Changing the Picture setting... 4 Changing the Sound setting... 5 Changing the Channel Setup setting... 6 Changing the Setup setting... 8 Viewing Teletext... 9 Enjoying stereo or bilingual programs... 0 Listening to FM Radio... Troubleshooting... Specifications... Back cover GB 3

4 x Securing the TV To prevent the TV from falling, use the supplied screws, clamps and band to secure the TV. Use only the supplied screws. Use of other screws may damage the TV. 0 mm 3.8 mm screws clamps band or Screw the band to the TV stand and to the provided hole at the rear of your TV. () Put a cord or chain through the clamps. () Screw one clamp to a wall or pillar and the other clamp to the provided hole at the rear of your TV. x Getting Started Step Insert the batteries (supplied) into the remote. b Note Do not use old or different types of batteries together. Step Connect the antenna cable (not supplied) to 8 (antenna input) at the rear of the TV. Tips Your TV can receive both TV and FM radio signals from the appropriate connections through the 8 (antenna input) terminal (see page 8). You can also connect your TV to other optional components (see page 8). b Step 3 Plug in the power cord, then press! on the TV to turn it on. Note The (standby) indicator flashes green for a few seconds when turning on the TV. This does not indicate a malfunction. Initial Setup Language: English Step 4 Set up the TV by following the instructions of the Initial Setup menu (see page 5). End 4

5 x Setting up your TV ( Initial Setup ) When you turn on your TV for the first time, the Initial Setup menu will appear. You may change the menu language, preset the TV channels automatically, sort or edit the channels and adjust the picture position using the buttons on the remote control or TV top control panel. Press V or v to select the desired menu language, then press. Initial Setup Language: English The selected menu language appears. End 3 Press V or v to select Yes, then press to preset the channels automatically. The screen will indicate automatic presetting is in progress. After all available channels have been tuned and stored, the Program Sorting/Edit menu appears automatically on the screen. To skip automatic channel presetting, select No, then press. If the message No channel found. Please connect cable/antenna appears, check your TV connections, then press. The Program Sorting/Edit menu enables you to sort and edit the channels. a) If you wish to keep the channels in the current condition, press WEGA GATE to exit. b) Press V or v to select the program number with the channel you wish to change. The selected channel will appear on the screen. c) If you wish to store the channels in a different order: ) Press b to enter sorting mode. ) Press V or v to select the new program number position for your selected channel, then press B. Initial Setup First please connect cable/ antenna Start Auto Program now? Yes No Auto Program Program: TV System: VHF Low Program Sorting/Edit PROG Label Skip Sorting: Edit: Program Sorting/Edit PROG Label Skip Sorting mode End End Exit Exit 0 Auto continue 5

6 Setting up your TV ( Initial Setup ) (continued) 4 5 d) If you wish to edit the channels, press to change to edit mode. Press b until the mode that you wish to edit is highlighted: Label, Skip, (block symbol). Then press. ) To label, press V or v to select the alphanumeric characters for the label. Then press. ) To skip the program number, press V or v to select On. Then press. You can skip this program number when using PROG +/-. 3) To block unwanted program number, press V or v to select. Then press. e) Repeat step b) to d) if you wish to change other channels. Press WEGA GATE to go to the next menu. Press B or b to adjust the bars on the top and bottom of the menu if they are slanted, then press. If no adjustment is necessary, then press. To prevent this Initial Setup menu from appearing again when you turn on the TV by pressing!, press V or v to select No, then press. To allow this menu to appear again, select Yes, then press. Program Sorting/Edit PROG Label Skip Edit mode Picture Rotation Initial Setup Program Sorting/Edit PROG Label Skip Edit mode Program Sorting/Edit PROG Label Skip Edit mode End Display this menu next time? Yes No Exit Exit Exit Tip You can immediately go to the end of the Initial Setup menu by pressing WEGA GATE. 6

7 L (MONO) R x TV top control, front and rear panels TV top control panel WEGA GATE FM PROG TV rear panel Y TV front panel ( MONO) L CB L ( MONO) CR R R L (MONO) R qf qd qs qa Button/Terminal Function Page! Turn off or turn on the TV. 4 Remote control sensor. - 3 Wake Up indicator. 3 Standby indicator. 4 4 i Headphone jack. - 5 t Video input terminal. 8 6 PROG +/ program number / Adjust volume. - 8 t TV or video input. 8 WEGA GATE menu operations 6,7 V,v,B,b and adjust items. 8 selected items. 9 WEGA GATE Display or cancel WEGA GATE menu. 0 FM Listen to FM radio. qa 8 Antenna input terminal. 8 qs T Monitor output terminal. 9 qd Component video input terminal. 9 qf t Video input terminal. 8 7

8 x Connecting optional components Connecting to the video input terminal ( t ) TV front panel Audio/Video cable (not supplied) Camcorder L (MONO) R Antenna cable (not supplied) TV, CATV, Satellite or When there is no FM signal TV rear panel Antenna selector FM signal Y TV signal (MONO) L CB C R L (MONO) Antenna cable (not supplied) R R Audio/Video cable (not supplied) VCR S Video cable (not supplied) DVD player Notes If you connect a VCR to 8 (antenna input), preset the signal output from the VCR to the program number 0 on the TV (see page 7). When both (S video) and (video) for t are connected at the same time, (S video) is automatically selected. To view (video), disconnect the S video cable. 8

9 Connecting to the monitor output terminal ( T ) TV rear panel Y Audio system C B (MONO) L R C R L (MONO) R Audio/Video cable (not supplied) VCR Connecting to the component video input terminal ( ) TV rear panel (MONO) L Y C B L (MONO) Component video cable (not supplied) R C R R DVD player Audio cable (not supplied) Notes If your DVD player can output interlace and progressive mode signals, select the interlace output when connecting to (component video input) on your TV. Your TV can receive either 55i/60Hz or 65i/50Hz interlace signals. The component video terminals on your DVD player are sometimes labeled Y/CB/CR, Y/PB/ PR, Y/Cb/Cr or Y/B-Y/R-Y. If you select DVD on your TV screen, the signal from the T (monitor output) jacks will not be output properly. This does not indicate a malfunction. 9

10 x Using the remote control and basic functions 0 qa qs qd qf qg qh qj qk ql w; A/B RETURN TV PROG WEGA GATE Button Description Page?/ Turn off temporarily or turn on the TV. a Display the TV program. 3 Jump to last program number that has been watched for at least five seconds. 4 PROG +/ program number. 5 +/ Adjust volume. 8 Change the picture size: On (6:9 wide-mode),. 9 surround mode options: 5 TruSurround, WOW, Simulated,. 0 Display on-screen information. qa Mute the sound. qd t TV or video input. 8 qf 0 9 Input numbers. For program number 0 and above, enter the second digit within two seconds. ql sound mode options 5 Dynamic k 3k 8k with a 5-Band Graphic Equalizer display: Dynamic, Standard, Custom *. Standard k 3k 8k Custom * When the Custom mode is selected, you can receive the last adjusted sound settings from the Sound Adjustment option in the menu k 3k 8k w; picture mode options: 4 Vivid, Standard, Custom *. * When the Custom mode is selected, you can receive the last adjusted picture settings from the Picture Adjustment option in the menu. 0

11 Button Description Page WEGA GATE menu operations 6 selected items. 7 WEGA GATE Display or cancel WEGA GATE menu. qj V, v, B, b and adjust items. qk RETURN Return to the previous level. Timer operations qg Set TV to turn on automatically according to the (Wake Up Timer) desired period of time (max. of hours). The indicator on TV lights up amber once you set the wake up timer. If no buttons or controls are pressed for more than one hour after the TV is turned on using the wake up timer, the TV automatically goes into standby mode. qh Set TV to turn off automatically according to the (Sleep Timer) desired period of time (max. of one hour and 30 min.). Teletext operations (green label),,,, All buttons are used for Teletext operations. 9,,,, (red, green, yellow, blue) PIP operations,, V, v, B, b Not function for your TV. Stereo/bilingual operations qs A/B stereo/bilingual mode. 0 WOW, TruSurround, SRS and symbol are trademarks of SRS Labs, Inc. WOW and TruSurround technologies are incorporated under license from SRS Labs, Inc. Licensed by BBE Sound, Inc. under USP463858, BBE and BBE symbol are trademarks of BBE Sound, Inc.

12 x Introducing the WEGA GATE navigator WEGA GATE is a gateway that allows you access to preset TV channels, connected external inputs, FM Radio mode and Settings menu. WEGA GATE TV TV 0 External Inputs FM Radio Settings TV End watch the preset TV channels (see page 5) External Inputs External Inputs Video Video DVD End FM Radio select the inputs for the connected equipment (see page 8) FM Radio Preset : Please setup FM Radio Preset -9 Search Fine Exit listen to the FM Radio (see page ) Settings Picture Picture Mode: Vivid Picture Adjustment Color Temperature: Cool VM: High Intelligent Picture: On change the settings of your TV (see page 3) How to use WEGA GATE End WEGA GATE TV External Inputs FM Radio Settings TV End () Press WEGA GATE to display or cancel the WEGA GATE menu. (3) Press V or v to select the desired item. TV End WEGA GATE TV External Inputs FM Radio Settings () Press (or b) to confirm your selection or go to the next level. Tip The WEGA GATE, operations above. (4) Press RETURN to move to the previous level. and V,v,B,b buttons on the top control panel can also be used for the

13 x Settings Adjustment You are able to change the settings of your TV from Settings in WEGA GATE menu. Press WEGA GATE button to display WEGA GATE menu. Press V or v to select Settings and press. The following is an overview of the items that can be adjusted. Picture Picture Mode: Vivid Picture Adjustment Color Temperature: Cool VM: High Intelligent Picture: On End Picture (see page 4) Picture Mode : Vivid Standard Custom Picture Adjustment : Picture, Brightness, Color, Hue, Sharpness, Reset Color Temperature : Cool Neutral Warm VM : High Low Intelligent Picture : On Sound Sound Mode: Dynamic Sound Adjustment Balance Intelligent Volume: Surround: End Sound (see page 5) Sound Mode : Dynamic Standard Custom Sound Adjustment : Adjust, Reset Balance Intelligent Volume : On Surround : TruSurround WOW Simulated Channel Setup Auto Program Manual Program Program Sorting/Edit FM Radio Setup End Channel Setup (see page 6) Auto Program Manual Program Program : TV System : B/G I D/K M VHF Low / VHF High / UHF Fine : Auto Manual Signal Booster : Auto Program Sorting/Edit FM Radio Setup Setup Language: English Picture Rotation Video Label Color System: Wake Up Timer Beep: Auto On Factory Settings End Setup (see page 8) Language : English (Chinese) Picture Rotation Video Label : Video Input, Label Color System : Auto PAL SECAM NTSC3.58 NTSC4.43 Wake Up Timer Beep : On Factory Settings : Yes No Note When a feature is dimmed in the menu, it is not selectable. 3

14 x Changing the Picture setting 3 The Picture menu allows you to adjust the picture settings. Press WEGA GATE and select Settings. Make sure the Picture icon ( ) is selected, then press. Press V or v to select the desired item (e.g., Picture Mode ), then press. Picture Mode Color Temperature VM (Velocity Modulation) Intelligent Picture To choose either Vivid (contrast and sharp), Standard (normal) or Custom *. adjust white color tint. Choose either Cool (blue tint), Neutral (neutral tint) or Warm (red tint). sharpen the edges of each object. Choose either High, Low or. optimize picture quality. Press V or v to select On, then press. To cancel, select, then press. * You can adjust the setting to your personal preference in the Picture Adjustment, Color Temperature and VM options only when the Custom mode is selected. Adjusting the Picture Adjustment items under Custom mode 3 Press V or v to select either Picture (contrast), Brightness, Color, Hue (color tones) or Sharpness, then press. ing Reset will set your TV to the factory settings. Press V,v,B or b to adjust the setting of your selected item, then press. Repeat the above steps to adjust other items. The adjusted settings will be received when you select Custom. Notes Hue can be adjusted for the NTSC color system only. Reducing Sharpness can also reduce picture noise. 4

15 x Changing the Sound setting 3 The Sound menu allows you to adjust the sound settings. Press WEGA GATE and select Settings. Press V or v to select the Sound icon ( ), then press. Press V or v to select the desired item (e.g., Sound Mode ), then press. Sound Mode Balance Intelligent Volume To choose either Dynamic (low and high tones), Standard (voice and high tones) or Custom *. Press v or B to emphasize the left speaker. Press V or b to emphasize the right speaker. adjust the volume of all program numbers and video inputs automatically. Press V or v to select On, then press. To cancel, select, then press. Surround choose either TruSurround (surround sound that spreads out to the rear of a room), WOW ** (full, deep bass sound), Simulated (stereo-like monaural sound) or. * You can adjust the setting to your personal preference in the Sound Adjustment option only when the Custom mode is selected. ** BBE High Definition Sound is fully activated maximizing the sound effect in the WOW mode. Note Intelligent Volume is not selectable when TruSurround is selected. Adjusting the Sound Adjustment items under Custom mode The 5-Band Graphic Equalizer feature allows you to adjust sound frequency settings of Custom mode in the menu. Make sure that Adjust is selected, then press. ing Reset will set your TV to the factory settings. Press B or b to select the desired sound frequency, then press V or v to adjust the setting and press. The adjusted settings will be received when you select Custom. Notes Adjusting higher frequency will affect higher pitched sound and adjusting lower frequency will affect lower pitched sound. You may display the settings directly by using button on the remote control (see page 0). 5

16 x Changing the Channel Setup setting 3 The Channel Setup menu allows you to preset channels automatically, manually preset channels, sort or edit the channels and preset FM Radio stations. Press WEGA GATE and select Settings. Press V or v to select the Channel Setup icon ( ), then press. Press V or v to select the desired item (e.g., Auto Program ), then press. Auto Program Manual Program Program Sorting/Edit FM Radio Setup * To preset channels automatically. manually preset desired channels and channels that cannot be preset automatically (see Presetting channels manually in page 7). change the order in which the channels appear on the screen, label the program number, skip the program number and block unwanted programs. (see step 3 of the section Initial Setup in page 5). preset up to nine FM radio stations. You can manually preset each FM radio station that can be received in your area and then store the radio frequency of the desired FM radio stations. () Press V or v to select the desired FM radio station position, then press. () Press V or v to search the FM radio stations. Searching stops automatically when a station is tuned in. If the station has a weak signal, press B or b to fine tune the radio frequency manually, then press to store the FM radio station. (3) You may edit the FM radio station label. Press V or v to select alphanumeric characters for the label, then press. (4) Repeat steps () through (3) to preset other FM radio stations. * The FM Radio Setup feature is only available in FM Radio mode. To enable this feature, access to FM Radio mode by using WEGA GATE system (see page ) or pressing the FM button on the top control panel (see page 7), then preset your desired FM radio stations according to the steps mentioned above. Notes If you preset a blocked program number, that program number will be unblocked automatically. If you sort a blocked program, that program will remain blocked. 6

17 Presetting channels manually After selecting Manual Program, select the program number to which you want to preset a channel. () Make sure Program is selected, then press. () Press V or v until the program number you want to preset appears on the menu, then press. the desired channel. () Make sure either VHF Low, VHF High or UHF is selected, then press. () Press V or v until the desired channel s broadcast appears on the TV screen, then press. If the sound of the desired channel is abnormal, select the appropriate TV system. () Press V or v to select TV System, then press. () Press V or v until the sound becomes normal, then press. If you are not satisfied with the picture and sound quality, you may be able to improve them by using the Fine tuning feature. () Press V or v to select Fine, then press. () Press V or v to select Manual, then press. (3) Press V,v,B or b until the picture and sound quality are optimal, then press. The + or icon on the menu flashes while tuning. If the TV signal is too strong (picture distorted; picture with lines; signal interference) or weak (snowy picture), you may be able to improve the picture quality by setting the Signal Booster feature. () Press V or v to select Signal Booster, then press. () Press V or v to select either (for picture distorted; picture with lines; signal interference) or Auto (for snowy picture), then press. 0 7

18 x Changing the Setup setting 3 The Setup menu allows you to change the menu language, adjust the picture position, label the connected equipment, select the color system, set the wake up timer beep and reset your TV to factory settings. Press WEGA GATE and select Settings. Press V or v to select the Setup icon ( ), then press. Press V or v to select the desired item (e.g., Language ), then press. Language To change the menu language. Press V or v to select either English or press. (Chinese), then Picture Rotation Video Label Color System Wake Up Timer Beep Factory Settings adjust the picture position when it is not aligned with the TV screen. Press B or b to adjust the picture position, then press. label the connected equipment. () Video Input and press. Press V or v to select the input you want to label, then press. () Label and press, then press V or v to select the label options: Video / Video / DVD, VCR, SAT, Game or Edit *. * You may edit the video label to your favorite name. Press V or v to select alphanumeric characters for the label, then press. select the color system. Press V or v to select either Auto, PAL, SECAM, NTSC3.58 or NTSC4.43, then press. Normally, set this to Auto. allow your TV to emit beeping sound when TV switches on automatically using wake up timer. Press V or v to select On, then press. To cancel, select, then press. reset your TV to factory settings. Press and press V or v to select Yes, then press. To cancel, select No, then press. Notes Color system is not selectable in FM Radio mode. To ensure the beeping sound can be heard, you must set an appropriate volume level on your TV and make sure the TV is not in mute condition. To stop the beeping sound, press any buttons on the remote control or top control panel. If no button is pressed for three minutes, the beeping sound will automatically go off. 8

19 x Viewing Teletext Some TV stations broadcast an information service called Teletext which allows you to receive various information, such as stock market reports and news. You can use the buttons on the remote to view Teletext., (red, green, yellow, blue) A/B RETURN TV PROG WEGA GATE To Do this display a Teletext Press. Each time you press, the page on the screen changes as follows: TV picture Teletext t Teletext and TV t TV. If there is no Teletext broadcast, 00 is displayed at the top left corner of the screen. check the contents Press. of a Teletext service An overview of the Teletext contents, including page numbers, appears on the screen. select a Teletext page Press the number buttons to enter the three-digit page number of the desired Teletext page. If you make a mistake, reenter the correct page number. To access the next or previous page, press or. hold (pause) a Press to display the symbol at Teletext display the top left corner of the screen. To resume normal Teletext viewing, press. reveal concealed Press. information (e.g., To conceal the information, press the an answer to a quiz) button again. enlarge the Teletext Press. Each time you press, the display Teletext display changes as follows: Enlarge upper half t Enlarge lower half t Normal size. stand by for a Teletext () Enter the Teletext page number that page while watching you want to refer to, then press. a TV program () When the page number is displayed, press to show the text. select a FASTEXT Press (red, green, yellow and blue) menu or the colored that corresponds to the desired menu or boxes page number. turn off Teletext Press a. Note The FASTEXT feature can be used only when the FASTEXT broadcast is available. 9

20 x Enjoying stereo or bilingual programs You can enjoy stereo sound or bilingual programs of NICAM and A stereo systems by using the A/B button. When receiving a NICAM program Broadcasting On-screen display (ed sound) A/B A/B PROG NICAM stereo NICAM bilingual NICAM monaural NICAM (Stereo sound) t t Mono (Regular sound) NICAM Main t NICAM Sub t Mono (Main sound) (Sub sound) (Regular sound) t NICAM Main (Main sound) t Mono (Regular sound) t RETURN WEGA GATE When receiving an A program Broadcasting On-screen display (ed sound) A stereo Stereo (Stereo sound) t t Mono (Regular sound) TV A bilingual Main (Main sound) t Sub (Sub sound) t Note If the stereo sound is noisy when receiving a stereo program, select Mono. The sound becomes monaural but the noise is reduced. 0

21 x Listening to the FM Radio You are able to listen to the FM radio stations using your TV. To access to FM Radio mode: Press WEGA GATE button and select FM Radio (see page ). or Press FM button on the top control panel (see page 7). To exit from FM Radio mode: Press WEGA GATE button, select the desired items: TV or External Inputs, then press. the desired TV channel or external inputs and press. or Press FM button on the top control panel. A/B PROG +/ V, v, B, b WEGA GATE A/B RETURN TV PROG WEGA GATE Listening to preset stations 3 Access to FM Radio mode. Press WEGA GATE button and select Settings. Preset the desired FM radio stations in FM Radio Setup from Channel Setup menu (see page 6). Exit from Channel Setup menu by pressing WEGA GATE button. The selected preset FM radio station number and label will appear on the screen. To select the desired preset FM radio station, press PROG +/. Tip You can also use the -9 buttons on the remote control to directly select the desired preset FM radio station. Listening to non-preset stations 3 Access to FM Radio mode. Press V or v to search for the desired FM radio station. The preset number and label will not be displayed. If the station has a weak signal, press B or b to fine tune the radio frequency manually. Notes You can only operate V, v, B and b functions using the remote control buttons in FM Radio mode. The available radio frequency is only for temporary listening pleasure and cannot be stored in the memory. If the message Please setup FM Radio appears, display the Channel Setup menu and select FM Radio Setup to preset the desired FM radio stations (see page 6). Note When a FM stereo program has static noise, press A/B until Mono appears. There will be no stereo effect, but the noise will be reduced.

22 x Troubleshooting If you find any problem while viewing your TV, you can either use the Factory Settings function or check the Troubleshooting guide below. If the problem persists, contact your Sony dealer. Factory Settings function Press the WEGA GATE button. Choose Settings and go to Setup ( ) menu. From Setup menu, select Factory Settings. Then select Yes and press. Your TV will go blank for a few seconds, then the Initial Setup menu will appear. Your TV will be set to factory settings, but certain problems may be solved. Symptom Snowy picture, noisy sound Distorted picture, noisy sound Good picture, noisy sound No picture, no sound Good picture, no sound Dotted lines or stripes Double images or ghosts No color Solutions Check the antenna cable and connection on the TV, VCR and at the wall (see page 8). Check the antenna setup. Contact a Sony dealer for advice. Display the Channel Setup menu and select Manual Program to preset the channel again (see page 7). Display the Channel Setup menu and set the Signal Booster to Auto from Manual Program (see page 7). Try using an external booster. Turn off or disconnect the external booster if it is in use. Display the Channel Setup menu and set the Signal Booster to from Manual Program (see page 7). Display the Channel Setup menu and select the appropriate TV System from Manual Program (see page 7). Check the power cord, antenna and VCR connections (see page 8). Press?/ (power) to turn on the TV (see page 0). Press! (main power) on the TV to turn off the TV for about five seconds, then turn it on again (see page 7). Press + to increase the volume level (see page 0). Press to cancel the muting (see page 0). Do not use a hair dryer or other equipment near the TV. Check the antenna setup. Contact a Sony dealer for advice. Use a highly directional antenna. Use the fine tuning ( Fine ) function (see page 7). Check the antenna setup. Contact a Sony dealer for advice. Turn off or disconnect the external booster if it is in use. Display the Picture menu and select Custom from Picture Mode, then adjust the Color level from Picture Adjustment (see page 4). Display the Setup menu and check the Color System setting (usually set this to Auto ) (see page 8). Check the antenna setup. Contact a Sony dealer for advice.

23 Symptom Picture slant Abnormal color patches Teletext display is incomplete (snowy picture or double images). Solutions Keep external speakers or other electrical equipment away from the TV. Display the Setup menu and adjust Picture Rotation so that the picture position is optimal (see page 8). Keep external speakers or other equipment away from the TV. Do not move the TV while the TV is turned on. Press! (main power) on the TV to turn off the TV for about 5 minutes, then turn it on again to demagnetize the TV. Check the antenna cable and connection on the TV, VCR and at the wall (see page 8). Check the antenna setup. Contact a Sony dealer for advice. Display the Channel Setup menu and set the Signal Booster to Auto from Manual Program (see page 7). Try using an external booster. Use the fine tuning ( Fine ) function (see page 7). TV cannot receive stereo broadcast sound or stereo broadcast sound switches on and off or is distorted. TV cannot receive FM radio station. The (standby) indicator on your TV flashes red several times after every three seconds. The TV screen sometimes goes blank for slightly longer than usual during channel change. TV cabinet creaks. A small boom sound is heard when the TV is turned on. Check the antenna cable and connection on the TV, VCR and at the wall (see page 8). Check the antenna setup. Contact a Sony dealer for advice. Connect a separate FM antenna and the TV channel source through an antenna selector (switch) to your TV (see page 8). Count the number of times the (standby) indicator flashes. Press! (main power) to turn off your TV. Contact your nearest Sony service center. The Signal Booster is functioning to detect a weak signal. This does not indicate a malfunction. Changes in room temperature sometimes make the TV cabinet expand or contract, causing a noise. This does not indicate a malfunction. The TV s demagnetizing function is working. This does not indicate a malfunction. 3

24 0-40

25 WEGA GATE CT 3

26 x x Initial Setup Language: b b English ! 4 Initial Setup 5 End 4

27 x Initial Setup V v V v 0 3 a) WEGA GATE b) V v c) ) b ) V v B PROG PROG

28 d) b ) V v ) V v PROG +/ 3) V v e) b) d) PROG PROG PROG 4 WEGA GATE B b 5! V v WEGA GATE 6

29 L (MONO) R x WEGA GATE FM PROG Y ( MONO) L CB L ( MONO) CR R R L (MONO) 5 R 4 3 qf qd qs qa! i 5 t 8 6 PROG +/ 7 +/ 8 t 8 WEGA GATE 6, 7 V,v,B,b 8 9 WEGA GATE WEGA GATE 0 FM qa 8 8 qs T 9 qd DVD 9 qf t 8 7

30 x t L (MONO) R Y (MONO) L CB C R L (MONO) R R S DVD S t S S 8

31 T Y C B (MONO) L L (MONO) R C R R DVD (MONO) L Y C B L (MONO) DVD R C R R DVD DVD DVD 55i/60 65i/50 DVD Y/CB/CR, Y/PB/PR, Y/Cb/Cr Y/B-Y/R-Y DVD T 9

32 x 0 qa qs qd qf qg qh qj qk ql w; A/B RETURN TV PROG WEGA GATE ? a 3 4 PROG +/ 5 +/ 8 6:9 9 5 TruSurround WOW 0 qa qd t 8 qf ql 5-Band Graphic Equalizer 5 * k 3k 8k k 3k 8k * k 3k 8k w; 4 * * 0

33 WEGA GATE 6 7 WEGA GATE WEGA GATE qj V, v, B, b qk RETURN qg qh 30,,,, 9,,,,,, V, v, B, b qs A/B 0 WOW, TruSurround, SRS SRS Labs, Inc. WOW TruSurround SRS Labs, Inc. BBE , BBE BBE BBE

34 x WEGA GATE WEGA GATE WEGA GATE DVD WEGA GATE WEGA GATE 电视 选择结束 确认 () WEGA GATE WEGA GATE (3) V v WEGA GATE () b (4) RETURN WEGA GATE V,v,B,b

35 x WEGA GATE WEGA GATE WEGA GATE V v 4 5 TruSurround WOW B/G I D/K M VHF / VHF / UHF Language: 8 Language English PAL SECAM NTSC3.58 NTSC4.43 3

36 x 3 WEGA GATE V v * V v * V v V v B b 3 NTSC 4

37 x 3 WEGA GATE V v V v * v B V b V v TruSurround WOW ** * ** BBE WOW TruSurround 5-Band Graphic Equalizer 5 B bv v 0 5

38 x 3 WEGA GATE V v V v * 9 V v V v B b 3 V v 4 3 * WEGA GATE FM 7 6

39 V v VHF 0 VHF VHF UHF V v 3 V v V v 4 V v V v 3 V v B b + 5 V v V v 7

40 x 3 WEGA GATE V v V v /Language Language V v English B b V v V v DVD * * V v V v PAL SECAM NTSC 3.58 NTSC 4.43 V v V v 8

41 x, A/B RETURN TV PROG WEGA GATE t t () FASTEXT t t 00 () a FASTEXT FASTEXT 9

42 x A/B NICAM A A/B A/B PROG t t t t t t t t t t t RETURN WEGA GATE A TV A A 0

43 x WEGA GATE FM 7 WEGA GATE FM A/B PROG +/ V v B b WEGA GATE A/B RETURN TV PROG WEGA GATE 3 WEGA GATE 6 WEGA GATE PROG +/ 9 V v B b 3 V v B b 6 FM A/B

44 x Sony WEGA GATE ( Settings ) ( Setup ) 8 Sony ?/ 0! Sony 7 Sony 4 8 Sony

45 8!5 8 Sony Sony 8! Sony 3

46 AMARAN TV anda bervoltan tinggi yang membahayakan. Voltan pengendalian TV: 0 40 V AC. Jangan sambungkan palam wayar kuasa TV sebelum anda selesai membuat semua sambungan yang lain; jika tidak, kebocoran arus yang minimum mungkin mengalir menerusi antena dan terminal lain ke bumi. Untuk mengelakkan kebocoran bateri dan kerosakan alat kawalan jauh, keluarkan bateri dari alat kawalan jauh jika anda tidak menggunakannya untuk beberapa hari. Jika anda tersentuh sebarang cecair yang terbocor dari bateri, sila cuci dengan air secepat mungkin. Untuk keselamatan diri, jangan sentuh mana-mana bahagian TV, wayar kuasa dan kabel antena semasa kilat. Untuk keselamatan kanak-kanak, jangan biarkan mereka menghampiri TV bersendirian. Jangan benarkan kanak-kanak memanjat TV. Untuk mengelakkan dari berlakunya kebakaran atau litar pintas, jangan dedahkan TV kepada hujan atau kelembapan. Jangan letak sebarang benda di atas TV anda. Jangan dedahkan TV kepada titisan atau percikan cecair dan jangan letak sebarang benda yang mengandungi cecair seperti bekas bunga di atas TV anda. Jangan pasang TV sekiranya terdapat sebarang tumpahan cecair atau pepejal yang terjatuh ke dalamnya. Pemeriksaan segera harus dilakukan oleh orang yang berkelayakan sahaja. Pasangkan TV di atas rak TV dan lantai yang stabil serta boleh menyokong berat TV anda. Pastikan permukaan rak TV adalah rata dan luasnya adalah lebih besar daripada luas permukaan bawah TV. Jangan halang ruang pengudaraan TV. Jangan letakkan TV di tempat yang tertutup seperti rak buku atau kabinet. TV anda hanya untuk kegunaan di rumah sahaja. Jangan gunakan TV anda dalam sebarang kenderaan atau di tempat yang amat berhabuk, panas, lembap atau di tempat yang mengalami gegaran yang melampau. Jangan sambungkan terlalu banyak perkakas elektrik kepada satu soket kuasa. Jangan rosakkan wayar. Jangan buka kabinet dan penutup belakang TV kerana terdapat voltan yang tinggi dan bahagian yang merbahaya di dalam TV. Kerja membaiki dan membuang TV hendaklah dilakukan oleh orang yang berkelayakan sahaja. Bersihkan TV dengan kain yang kering dan lembut. Jangan gunakan benzina, pencair atau bahan kimia yang lain untuk membersihkan TV. Jangan lekatkan apa-apa (contohnya, pita pelekat, pita selofan, gam) pada kabinet bercat TV anda. Jangan calarkan tiub gambar. Pegang palam untuk menarik keluar wayar kuasa TV. Jangan terus tarik wayar kuasa. Walaupun TV anda telah ditutup, TV anda masih bersambung kepada sumber kuasa AC (kuasa utama) selagi wayar kuasa TV disambungkan ke soket. Cabut wayar kuasa TV sebelum memindahkan TV anda atau jika anda tidak menggunakan TV untuk beberapa hari.

47 Kandungan Keselamatan TV anda... 4 Persediaan Awal... 4 Mengaturkan TV anda ( Initial Setup )... 5 Panel kawalan atas, hadapan dan belakang TV... 7 Menyambung komponen pilihan... 8 Menggunakan alat kawalan jauh dan fungsi asas... 0 Memperkenalkan penunjuk WEGA GATE... Melaraskan Settings... 3 Menukar aturan Picture... 4 Menukar aturan Sound... 5 Menukar aturan Channel Setup... 6 Menukar aturan Setup... 8 Menonton Teleteks... 9 Menikmati rancangan stereo atau rancangan dwibahasa... 0 Mendengar FM Radio... Penyelesaian masalah... Specifications... Muka surat terakhir MY 3

48 x Keselamatan TV anda Untuk menghindarkan TV anda daripada terjatuh, gunakan skru, pengapit dan pita yang dibekalkan. Gunakan skru yang dibekalkan sahaja. Penggunaan skru yang berlainan jenis boleh merosakkan TV anda. 0 mm 3.8 mm skru pengapit pita Skrukan pita kepada rak TV dan lubang yang disediakan di bahagian belakang TV anda. atau () Masukkan wayar atau rantai menerusi pengapit. () Skrukan salah satu pengapit pada dinding atau tiang dan skrukan satu pengapit lagi pada lubang yang disediakan di bahagian belakang TV anda. 4 x Persediaan Awal Initial Setup Language: b b English End Langkah Masukkan bateri (dibekalkan) ke dalam alat kawalan jauh. Nota Jangan gunakan bateri lama atau bateri yang berlainan jenis bersama-sama. Langkah Sambungkan kabel antena (tidak dibekalkan) kepada terminal 8 (input antena) yang terdapat di belakang TV anda. Panduan TV anda boleh menerima kedua-dua isyarat TV dan FM radio daripada sambungan yang bersesuaian melalui terminal 8 (input antena) (rujuk halaman 8). Anda juga boleh menyambungkan komponen pilihan kepada TV anda (rujuk halaman 8). Langkah 3 Sambungkan wayar kuasa TV, kemudian tekan! pada TV untuk memasangkan TV anda. Nota Penunjuk (standby) berkelip-kelip dengan warna hijau selama beberapa saat apabila anda memasang TV anda. Ini tidak menandakan TV anda mempunyai masalah. Langkah 4 Aturkan TV anda dengan mengikuti arahan menu Initial Setup (rujuk halaman 5).

49 x Mengaturkan TV anda ( Initial Setup ) Apabila anda memasangkan TV pada kali pertama, menu Initial Setup akan muncul. Anda boleh menukar bahasa menu, mengatur saluran TV secara automatik, menukar susunan saluran atau menyunting saluran dan melaraskan kedudukan gambar dengan menggunakan butang pada alat kawalan jauh atau panel kawalan atas TV. Tekan V atau v untuk memilih bahasa menu yang dikehendaki, kemudian tekan. Bahasa menu yang dipilih akan muncul. Initial Setup Language: English End 3 Tekan V atau v untuk memilih Yes, kemudian tekan untuk mengatur saluran secara automatik. Skrin TV akan menunjukkan pengaturan automatik sedang dijalankan. Setelah semua saluran yang boleh didapati selesai ditala dan disimpan, menu Program Sorting/Edit akan muncul secara automatik pada skrin. Untuk melangkau pengaturan saluran secara automatik, pilih No, kemudian tekan. Jika mesej No channel found. Please connect cable/antenna muncul, periksa sambungan TV anda, kemudian tekan. Menu Program Sorting/Edit membolehkan anda menukar susunan saluran dan menyunting saluran. a) Jika anda ingin simpan saluran dalam keadaan sekarang, tekan WEGA GATE untuk keluar. b) Tekan V atau v untuk memilih nombor rancangan dengan saluran yang anda ingin tukar. Saluran yang dipilih akan muncul pada skrin. c) Jika anda ingin simpan saluran dalam susunan yang berlainan: ) Tekan b untuk masuk mod susunan saluran. ) Tekan V atau v untuk memilih kedudukan nombor rancangan yang baru untuk saluran yang dipilih, kemudian tekan B. Initial Setup First please connect cable/ antenna Start Auto Program now? Yes No Auto Program Program: TV System: VHF Low Program Sorting/Edit PROG Label Skip Sorting: Edit: End End Exit Program Sorting/Edit PROG Label Skip Sorting mode Exit 0 Auto bersambung 5

50 Mengaturkan TV anda ( Initial Setup ) (sambungan) 4 d) Jika anda ingin menyunting saluran, tekan untuk menukar kepada mod menyunting. Tekan b sehingga mod yang anda ingin menyunting dipilih: Label, Langkau, (simbol sekatan). Kemudian tekan. ) Untuk melabel, tekan V atau v untuk memilih abjad nombor untuk label tersebut. Kemudian tekan. ) Untuk melangkau nombor rancangan, tekan V atau v untuk memilih On. Kemudian tekan. Anda boleh melangkau nombor rancangan ini ketika menggunakan PROG +/. 3) Untuk menyekat nombor rancangan yang tidak diingini, tekan V atau v untuk memilih. Kemudian tekan. e) Ulangi langkah b) ke d) jika anda ingin menukar saluran yang lain. Tekan WEGA GATE untuk pergi ke menu yang seterusnya. Tekan B atau b untuk melaraskan jaluran di atas dan di bawah menu jika ia senget, kemudian tekan. Jika tidak perlu melaraskannya, tekan. Program Sorting/Edit PROG Label Skip Edit mode Program Sorting/Edit PROG Label Skip Edit mode Program Sorting/Edit PROG Label Skip Edit mode Picture Rotation End Exit Exit Exit 5 Untuk mengelakkan menu Initial Setup muncul lagi jika anda memasangkan TV dengan menekan!, tekan V atau v untuk memilih No, kemudian tekan. Untuk membolehkan menu ini muncul lagi, pilih Yes, kemudian tekan. Initial Setup Display this menu next time? Yes No Panduan Anda boleh terus ke paparan menu Initial Setup yang terakhir dengan menekan WEGA GATE. 6

51 L (MONO) R x Panel kawalan atas, hadapan dan belakang TV Panel kawalan atas TV WEGA GATE FM PROG Panel belakang TV Y Panel hadapan TV ( MONO) L CB L ( MONO) CR R R L (MONO) R qf qd qs qa Butang/Terminal Fungsi Halaman! Menutup atau memasang TV. 4 Pengesan alat kawalan jauh. - 3 Penunjuk Bangun Tidur. 3 Penunjuk standby. 4 4 i Terminal Headphone. - 5 t Terminal input video. 8 6 PROG +/ Memilih nombor rancangan / Melaraskan paras bunyi. - 8 t Memilih input TV atau video. 8 Operasi menu WEGA GATE 6,7 V,v,B,b Memilih dan melaraskan butiran. 8 Mengesahkan butiran yang dipilih. 9 WEGA GATE Memapar atau membatalkan menu WEGA GATE. 0 FM Mendengar FM radio. qa 8 Terminal input antena. 8 qs T Terminal output monitor. 9 qd Terminal input komponen video. 9 qf t Terminal input video. 8 7

52 x Menyambung komponen pilihan Menyambungkan kepada terminal input video ( t ) Panel hadapan TV Kabel Audio/Video (tidak dibekalkan) kamkorder L (MONO) R Kabel antena (tidak dibekalkan) TV, TV Kabel, Satelit atau Apabila tiada isyarat FM Panel belakang TV Pemilih antena Isyarat FM (MONO) L Y C B L (MONO) Kabel antena (tidak dibekalkan) Isyarat TV R C R R Kabel Audio/ Video (tidak dibekalkan) Kabel Video S (tidak dibekalkan) Perakam pita video Pemain DVD Nota Jika anda menyambungkan VCR kepada 8 (input antena), aturkan output isyarat dari VCR kepada nombor rancangan 0 pada TV (rujuk halaman 7). Apabila kedua-dua (S video) dan (video) untuk t disambungkan serentak, (S video) akan dipilih secara automatik. Untuk menonton (video), putuskan sambungan kabel S video. 8

53 Menyambungkan kepada terminal output monitor ( T ) Panel belakang TV Y Sistem audio C B (MONO) L R C R L (MONO) R Kabel Audio/ Video (tidak dibekalkan) Perakam pita video Menyambungkan kepada terminal input komponen video ( ) Panel belakang TV (MONO) L Y C B L (MONO) Kabel komponen video (tidak dibekalkan) R C R R Pemain DVD Kabel audio (tidak dibekalkan) Nota Jika pemain DVD anda boleh mengeluarkan isyarat mod interlace dan progressive, pilih output interlace apabila menyambungkan kepada (input komponen video) pada TV anda. TV anda boleh menerima sama ada isyarat interlace 55i/60Hz atau 65i/50Hz. Terminal komponen video pada pemain DVD anda mungkin ditanda sebagai Y/CB/CR, Y/PB/ PR, Y/Cb/Cr atau Y/B-Y/R-Y. Jika anda memilih DVD di skrin TV anda, isyarat dari T (output monitor) tidak akan dikeluarkan dengan sempurna. Ini tidak menandakan TV anda mempunyai masalah. 9

54 x Menggunakan alat kawalan jauh dan fungsi asas 0 qa qs qd qf qg qh qj qk ql w; A/B RETURN TV PROG WEGA GATE Butang Deskripsi Halaman?/ Menutup sementara atau memasangkan TV. a Memaparkan input TV. 3 Kembali kepada nombor rancangan sebelumnya yang telah ditonton sekurangkurangnya lima saat. 4 PROG +/ Memilih nombor rancangan. 5 +/ Melaraskan paras bunyi. 8 Menukar saiz gambar: On (6:9 mod lebar),. 9 Memilih mod bunyi keliling: 5 TruSurround, WOW, Simulated,. 0 Memaparkan maklumat dalam skrin. qa Menghilangkan bunyi. qd t Memilih input TV atau video. 8 qf 0 9 Input nombor. Bagi nombor rancangan 0 dan ke atas, masukkan angka yang kedua dalam masa dua saat. ql Memilih pilihan mod bunyi 5 Dynamic k 3k 8k dengan paparan 5-Band Graphic Equalizer : Dynamic, Standard, Custom *. Standard k 3k 8k Custom * Apabila mod Custom dipilih, anda boleh menerima aturan bunyi yang terakhir dilaraskan daripada pilihan Sound Adjustment di dalam menu k 3k 8k w; Memilih pilihan mod gambar: 4 Vivid, Standard, Custom *. * Apabila mod Custom dipilih, anda boleh menerima aturan gambar yang terakhir dilaraskan daripada pilihan Picture Adjustment di dalam menu. 0

55 Butang Deskripsi Halaman Operasi menu WEGA GATE 6 Mengesahkan butiran yang dipilih. 7 WEGA GATE Memapar atau membatalkan menu WEGA GATE. qj V, v, B, b Memilih dan melaraskan butiran. qk RETURN Kembali ke paras yang sebelumnya. Operasi pemasa qg Setkan TV supaya dipasang mengikut tempoh masa (Pemasa bangun yang dikehendaki secara automatik (maks. jam). tidur) Penunjuk pada TV menyala dengan warna kuning jingga apabila anda sudah mengaturkan pemasa bangun tidur. Jika tidak ada butang atau kawalan ditekan setelah satu jam TV dipasang dengan menggunakan pemasa bangun tidur, TV akan berada dalam keadaan standby secara automatik. qh Setkan TV supaya ditutup mengikut tempoh masa yang (Pemasa tidur) dikehendaki secara automatik (maks. jam 30 min). Operasi Teleteks (label hijau),,,, Semua butang adalah digunakan untuk operasi 9,,,, Teleteks. (merah, hijau, kuning, biru) Operasi PIP,, V, v, B, b Tidak berfungsi pada TV anda. Operasi stereo/dwibahasa qs A/B Memilih mod stereo/dwibahasa. 0 Perkataan WOW, TruSurround, SRS dan simbol adalah cap dagang SRS Labs, Inc. Teknologi WOW dan TruSurround adalah digabungkan di bawah lesen SRS Labs, Inc. Dilesenkan oleh BBE Sound, Inc. di bawah USP463858, Perkataan BBE dan simbol BBE adalah cap dagang BBE Sound, Inc.

56 x Memperkenalkan penunjuk WEGA GATE WEGA GATE adalah satu laluan yang membolehkan anda memasuki saluran TV yang diaturkan, input luaran yang disambungkan, mod FM Radio dan menu Settings. WEGA GATE TV TV 0 External Inputs FM Radio Settings TV End menonton saluran TV yang diaturkan (rujuk halaman 5) External Inputs External Inputs Video Video DVD memilih input peralatan yang disambungkan (rujuk halaman 8) End Cara menggunakan WEGA GATE WEGA GATE TV External Inputs FM Radio Settings FM Radio Settings FM Radio Preset : Please setup FM Radio Preset -9 Search Fine Exit Picture Picture Mode: Vivid Picture Adjustment Color Temperature: Cool VM: High Intelligent Picture: On End TV End Mendengar FM Radio (rujuk halaman ) menukar aturan TV anda (rujuk halaman 3) () Tekan WEGA GATE untuk memapar atau membatalkan menu WEGA GATE. (3) Tekan V atau v untuk memilih butiran yang dikehendaki. TV End WEGA GATE TV External Inputs FM Radio Settings () Tekan (atau b) untuk mengesahkan pilihan anda atau pergi ke paras menu yang seterusnya. Panduan Butang WEGA GATE, operasi di atas. (4) Tekan RETURN untuk pergi ke paras yang sebelumnya. dan V,v,B,b pada panel kawalan atas boleh juga digunakan untuk

57 x Melaraskan Settings Anda boleh menukar aturan TV anda daripada Settings dalam menu WEGA GATE. Tekan butang WEGA GATE untuk memaparkan menu WEGA GATE. Tekan V atau v untuk memilih Settings dan tekan. Berikut adalah gambaran menyeluruh tentang butiran yang boleh dilaraskan. Picture Picture Mode: Vivid Picture Adjustment Color Temperature: Cool VM: High Intelligent Picture: On End Picture (rujuk halaman 4) Picture Mode : Vivid Standard Custom Picture Adjustment : Picture, Brightness, Color, Hue, Sharpness, Reset Color Temperature : Cool Neutral Warm VM : High Low Intelligent Picture : On Sound Sound Mode: Dynamic Sound Adjustment Balance Intelligent Volume: Surround: End Sound (rujuk halaman 5) Sound Mode : Dynamic Standard Custom Sound Adjustment : Adjust, Reset Balance Intelligent Volume : On Surround : TruSurround WOW Simulated Channel Setup Auto Program Manual Program Program Sorting/Edit FM Radio Setup End Channel Setup (rujuk halaman 6) Auto Program Manual Program Program : TV System : B/G I D/K M VHF Low / VHF High / UHF Fine : Auto Manual Signal Booster : Auto Program Sorting/Edit FM Radio Setup Setup Language: English Picture Rotation Video Label Color System: Wake Up Timer Beep: Auto On Factory Settings End Setup (rujuk halaman 8) Language : English (Bahasa Cina) Picture Rotation Video Label : Video Input, Label Color System : Auto PAL SECAM NTSC3.58 NTSC4.43 Wake Up Timer Beep : On Factory Settings : Yes No Nota Apabila ciri kelihatan malap di dalam menu, ia tidak boleh dipilih. 3

58 x Menukar aturan Picture 3 Menu Picture membenarkan anda menukar aturan gambar. Tekan WEGA GATE dan memilih Settings. Pastikan lambang Picture ( ) dipilih, kemudian tekan. Tekan V atau v untuk memilih butiran yang dikehendaki (contohnya, Picture Mode ), kemudian tekan. Pilih Picture Mode Color Temperature VM (Velocity Modulation) Intelligent Picture Untuk memilih Vivid (cerah dan tajam), Standard (biasa) atau Custom *. melaraskan warna putih. Memilih Cool (warna biru), Neutral (warna neutral) atau Warm (warna merah). menajamkan kejelasan tepi setiap objek. memilih High, Low atau. mengoptimumkan kualiti gambar. Tekan V atau v untuk memilih On, kemudian tekan. Untuk membatalkannya, pilih, kemudian tekan. * Anda boleh melaraskan aturan mengikut citarasa anda dalam pilihan Picture Adjustment, Color Temperature dan VM hanya apabila mod Custom dipilih. Melaraskan butiran Picture Adjustment di bawah mod Custom 3 Tekan V atau v untuk memilih Picture (kecerahan), Brightness, Color, Hue (keterangan warna) atau Sharpness, kemudian tekan. Memilih Reset akan mengaturkan TV anda kepada aturan kilang. Tekan V,v,B atau b untuk melaraskan aturan butiran pilihan anda, kemudian tekan. Ulangi langkah-langkah tersebut di atas untuk melaras butiran lain. Anda dapat menerima aturan yang telah dilaraskan apabila anda memilih Custom. Nota Hue boleh dilaras untuk sistem NTSC sahaja. Anda boleh mengurangkan Sharpness untuk mengurangkan gangguan gambar. 4