Contents 目录 1. 适用范围 Scope 电池组成 Battery Constitution 主要技术参数 Specification 电芯放电曲线图 Batteries discharge curve 电池尺寸 Batter

Size: px

Start display at page:

Download "Contents 目录 1. 适用范围 Scope 电池组成 Battery Constitution 主要技术参数 Specification 电芯放电曲线图 Batteries discharge curve 电池尺寸 Batter"

盼状贺
7 years ago
Views:

1 Specification Approval Sheet 锂离子电池规格承认书型号 Model: PL 样品数量 NO.OF SAMPLES: 容量 Cap : 2500mAh 送样日期 DATE OF SENDING SAMPLE: 版本 REV : A/0 客户代码 CUSTOMER CODE: 制定人 Prepared by 许永顺审核人 Checked by 批准人 Approved by 客户名 CUSTOMER NAME : BATTEX-Czech 业务员 THE SALESMAN : 客户确认 CUSTOMER APPROVAL 签章 STAMP 地址 : 深圳市龙华新区大浪街道华联工业区第 9 栋 Add: Building 9, hualian industrial park, dalang country, longhua new district, Shenzhen city 电话 (TEL): 传真 (FAX): 第 1 页

2 Contents 目录 1. 适用范围 Scope 电池组成 Battery Constitution 主要技术参数 Specification 电芯放电曲线图 Batteries discharge curve 电池尺寸 Battery Drawing 电池性能 Battery Performance 外观 Visual Inspection 标准测试条件 Standard Testing Condition 电性能 Electric Performance 机械性能测试 Mechanical Performance Testing 安全性能测试 Safety Performance Testing 高温储存性能测试 HT Storage Performance Testing 贮存及其它事项 Storage and Others 长期贮存 Long Time Storage 其它事项 Others... 7 Appendix 附录充电 Charging 充电电流 Charging current 充电电压 Charging voltage 充电温度 Charging temperature 禁止反向充电 Prohibition of reverse charging 放电 Discharging 放电电流 Discharging current 放电温度 Discharging temperature 过放电 Over-discharging 电池的注意事项 Handling Instructions... 9 安全警示 Caution... 9 使用说明 Guideline 第 2 页

3 1. 适用范围 Scope 仅适用于深圳倍特力电池有限公司生产的可充电锂离子电池或电池组, 包括锂离子电池电芯和保护组件 This document describes the product specification of lithium ion polymer battery or module which includes cell and protection devices supplied by Shenzhen BetterPower battery develop Co., Ltd. 2. 电池组成 Battery Constitution 序号 No. 名称 Name 型号 Model 备注 Remark 1 1 支锂离子电芯 One piece of cell 倍特力聚合物电池 PL PL 倍特力聚合物锂离子电池 BetterPower Polymer Lithium Ion Battery 2 铝转镍 Al and NI 宽度 4.0 毫米 Wide 4.0 mm 3. 主要技术参数 Specification 序号 NO. 项目 Items 标准 Criteria 备注 Remarks 典型容量 Typical capacity 最小容量 Minimum Capacity 2550 mah 2500 mah 0.2C 充放电至终止电压 0.2C charge and discharge for cut-off voltage 标称电压 Nominal Voltage 出货电压 Shipment voltage 内阻 Internal Impedance 充电截止电压 (V) Charge cut-off voltage 放电截止电压 (V) Discharge cut-off voltage 单支电芯约重 About heavy single batteries 标准充电电流 Standard charge current 最大充电电流 Max. charge current 3.70V V Cell: 50mΩ 4.20V 3.0V 45 g 标准充电后 AC 1KHz 测试 AC 1KHz after standard charge 500 ma 0.2C 1250 ma 0.5C 第 3 页

4 3.9 标准放电电流 Standard dis-charge current 500 ma 0.2C 3.10 最大放电电流 Max discharging current 1250 ma 0.5C 10 ~+25 最大充电 0.2C Max Charging 0.2C 3.11 工作温度 Operating Temperature 25 ~+45 最大充电 0.5C Max Charging 0.5C -20 ~+60 放电 Discharging 3.12 贮存温度 Storage Temperature -10 / / +35 小于一个月 Less than 1 month 小于六个月 Less than 6 months 4. 电芯放电曲线图 Batteries discharge curve 第 4 页

5 5. 电池尺寸 Battery Drawing 标识 Item T W L A B C D E F 描述 Description 厚度 Thickness 宽度 Width 高度 Length 极耳长度 Tab length 极耳中心距 Tab center distance 极耳宽度 Tab width 顶封位宽度 Top sealing width 极耳厚度 Tab thickness 极耳胶长度 Tab rubber length 尺寸规格 Dimension and specification 最大 9.1 毫米 9.1mm Max 最大 50.0 毫米 50.0mm Max 最大 51.0 毫米 51.0mm Max 10.0±2.0 毫米 10.0±2.0mm 32.0±2.0 毫米 32.0±2.0mm 3.8~4.2 毫米 3.8~4.2mm 3.6~4.5 毫米 3.6~4.5mm 0.1 毫米 0.1mm 0.2 ~2.5 毫米 0.2~2.5mm 第 5 页

6 6. 电池性能 Battery Performance 6.1 外观 Visual Inspection 电池外表面应保持干净清洁, 不能出现划痕凹点脏污漏液变形等不良现象 There shall be no such defects as scratch, flaw, crack, and leakage, which may adversely affect commercial value of the battery. 6.2 标准测试条件 Standard Testing Condition 除非另有说明, 涉及本规格书的所有测试项目均应在温度 25±5, 相对湿度 45%-75%RH 条件下进行 Unless otherwise specified, all tests stated in this product specification are conducted at below condition: Temperature: 25 5 C Humidity: 45%-75% RH 6.3 电性能 Electric Performance 序号项目 No. Items 标准充电模式 Standard Charge 循环 Cycle Life 电池温度性能 Temperature Performance of Battery 测试条件 Test Method and Condition 0.2C 恒流充电至 4.2V, 然后恒压充电至 0.02C Charge to 4.2V at constant current 0.2C, then constant voltage charge to taper current 0.02C (1) 充电过程 : 标准充电模式 ; (2) 放电过程 : 标准放电模式重复以上步骤 300 次 Charge: Standard charge model Discharge: Standard discharge model Repeat the procedures below 300 cycles 充电过程 : 标准充电模式放电过程 : 分别在 -10 C, 0 C 和 45 C 温度下以 0.2C 恒流放电至 3.0V Charge: Standard charge model Discharge: Discharge to 3.0V at 0.2C constant current at -10 C, 0 C and 45 C respectively 标准 Criteria 总充电时间不超过 6.5 小时, 其中在 25±2 环境下充电 ; Constant voltage 4.2V for 6.5hours in all at25± 次循环后放电容量大于等于第一次放电容量的 80% Residual capacity 80% after 300 cycles vs. Discharge capacity of first cycle -10 C 下, 容量 70% 0 C 下, 容量 80% 45 C 下, 容量 95% -10 C, capacity 70% 0 C, capacity 80% 45 C, Capacity 95% 6.4 机械性能测试 Mechanical Performance Testing 序号 No. 项目 Items 测试条件 Test Method and Condition 1 振动测试 Vibration Test 充满电电池按 X Y Z 三个方向, 每个方向上从 10HZ 55HZ 的频率循环扫描振动 90min 振动频率 10HZ~50HZ 位移幅值 ( 单振幅 0.8mm) After standard charging, fixed the capacitor to vibration table and subjected to vibration cycling that the frequency is to be varied at the rate of 1Hz per minute between 10Hz and 55Hz, the excursion of the vibration is 1.6mm. The capacitor shall be vibrated for 30 minutes per axis of XYZ axes. 判断标准 Criteria 不起火, 不爆炸, 不冒烟或漏液 No fire, no explode, no smoke or no leakage 2 跌落测试 Drop Test 电池完全充电后从 1300mm 高度由 X,Y,Z 正负 6 个方向自由跌落到置于水泥地面上 18mm-20mm 的厚木板上, 每个方向跌落 1 次, 最后用 1C 进行充放循环 3 次 Battery is dropped from a height of 1.3 meters 6 times at six angles (X, Y, Z plus positive, negative) to concrete ground, then cycle three times at 1C current. 不起火, 不爆炸, 不冒烟或漏液 No fire, no explode, no smoke or no leakage 第 6 页

7 6.5 安全性能测试 Safety Performance Testing 序号 No 项目 Items 过充电测试 Overcharge testing 热冲击实验 Hot oven test 过放电测试 Overdischarge testing 测试条件 Testing condition 充满电的电池外接 3C/4.6V 的电源给电池持续加载 2 小时 3C/4.6V DC power supply charge 2hrs after fully charge 将充满电的电池放在重力对流或循环空气的烘箱中进行加热, 烘箱的温度以 5±2 的速率上升到 130±2 后保温 30 分钟 Put a fully charged battery in a forced air oven and raise the temperature at 5±2 /min. to130±2 Rest for30 minutes 将电池放电至终止电压后, 以 30Ω 负载给电池持续加载 28 小时 Discharge 28hrs through 30Ω resistor after fully charge 标准 Criteria 不起火, 不爆炸, 不冒烟或漏液 No fire, no explode, no smoke or no leakage 不起火, 不爆炸, No fire, no explode 不起火, 不爆炸, 不冒烟或漏液 No fire, no explode, no smoke or no leakage 6.6 高温储存性能测试 HT Storage Performance Testing 序号 No. 项目 Items 测试条件 Testing condition 标准 Criteria 1 45 /7 天 45 /7 days 充满电电池在 45±2 高温箱中搁置 7 天, 再放电至终止电压 Storage 7 days at 45±2 oven after fully charge, then discharge to 3.0V at RT 不起火, 不爆炸, 不冒烟或漏液 No fire, no explode, no smoke or no leakage 容量衰减 < 10%, 内阻增加 < 30% Cap loss < 10%, imp increase < 30% 7. 贮存及其它事项 Storage and Others 7.1 长期贮存 Long Time Storage 长期贮存电池 ( 超过 3 个月 ) 须置于温度为 -10 ~30 湿度为 45%~75%RH 的环境中贮存电压为 3.75V~3.95V If the cell has to be stored for a long time (exceed three months), the environmental condition should be: Temperature: -10 ~30 Humidity: 45%~75%RH. The voltage for a long time storage should be 3.75V~3.95V. 7.2 其它事项 Others 任何本说明书中未提及的事项, 须经双方协商确定 Any matters that this specification does not cover should be conferred between the customer and BPI. 7.3 保质期限 Period of Warranty; 保质期从出厂日期 ( 喷码 ) 开始六个月 The period of warranty is six months from the date(printing) of shipment. 第 7 页

8 Appendix 附录聚合物锂离子充电电池操作指示及注意事项 Handling Precautions and Guideline For LIP (Lithium-Ion Polymer) Rechargeable Batteries 前言 Preface 本檔聚合物锂离子充电电芯操作指示及注意事项仅适用于深圳倍特力电池有限公司生产电芯 This document of 'Handling Precautions and Guideline LIP Rechargeable Batteries' shall be applied to the battery cells manufactured by BPI. 1 充电 Charging 1.1 充电电流 Charging current 充电电流不得超过本规格书中规定的最大充电电流使用高于推荐值电流充电将可能引起电芯的充放电性能机械性能和安全性能的问题, 并可能会导致发热或泄漏 Charging current should be less than maximum charge current specified in the Product Specification. Charging with higher current than recommended value may cause damage to cell electrical, mechanical, and safety performance and could lead to heat generation or leakage. 1.2 充电电压 Charging voltage 充电电压不得超过本规格书刊号中规定的额定电压充电器的设计应满足此条件电池电压高于额定电压值时, 将可能引起电芯的充放电性能机械性能和安全性能的问题, 可能会导致发热或泄漏 Charging shall be done by voltage less than that specified in the Product Specification. which is the absolute maximum voltage, must be strictly prohibited. The charger shall be designed to comply with this condition. It is very dangerous that charging with higher voltage than maximum voltage may cause damage to the cell electrical, mechanical safety performance and could lead to heat generation or leakage. 1.3 充电温度 Charging temperature 电池必须在 10 ~45 的环境温度范围内进行充电 The cell shall be charged within 10 ~45 range in the Product Specification. 1.4 禁止反向充电 Prohibition of reverse charging 正确连接电池的正负极, 严禁反向充电若电池正负极接反, 将无法对电芯进行充电同时, 反向充电会降低电芯的充放电性能安全性, 并会导致发热泄漏 Reverse charging is prohibited. The cell shall be connected correctly. The polarity has to be confirmed before wiring. In case of the cell is connected improperly, the cell cannot be charged.simultaneously, the reverse charging may cause damaging to the cell which 第 8 页

9 may lead to degradation of cell performance and damage the cell safety, and could cause heat generation or leakage. 2 放电 Discharging 2.1 放电电流 Discharging current The cell shall be discharged at less than the maximum discharge current specified in the Product Specification. High discharging current may reduce the discharging capacity significantly or cause over-heat. 放电电流不得超过本规格书规定的最大放电电流, 大电流放电会导致电芯容量剧减并导致过热 2.2 放电温度 Discharging temperature The cell shall be discharged within -20 ~60 range specified in the Product Specification. 电池必须在 -20 ~60 的环境温度范围内进行放电 2.3 过放电 Over-discharging 需要注意的是, 在电池长期未使用期间, 它可能会用其自放电特性而处于某种过放电状态为防止过放电的发生, 电池应定期充电, 将其电压维持在 3.75V 至 3.95V 之间 It should be noted that the cell would be at an over-discharged state by its self-discharge characteristics in case the cell is not used for long time. In order to prevent overdischarging, the cell shall be charged periodically to maintain between 3.75V and3.95v. 过放电会导致电芯性能电池功能的丧失 Over-discharging may causes loss of cell performance, characteristics, or battery functions. 3. 电池的注意事项 Handling Instructions 认真阅读下面的注意事项, 确保正确使用聚合物锂离子电池倍特力对违反下述注意事项而产生的任何问题不予负责 Read and observe the following warnings and precautions to ensure correct and safe use of Liion batteries. Danger! 危险! 安全警示及使用说明 Caution and Guideline 使用前应先阅读产品规格书以及安全警示, 确保正确使用电池和确保电池使用过程中的安全 Before using battery, please read specification and safety caution, insure proper application and safety. 安全警示 Caution 下面的操作可能导致电池泄漏, 发热甚至燃烧 : Failing in following items can cause leakage, heat even fire: 禁止反向充电! Prohibition of reverse charge of battery. 禁止过充电! Prohibition of overcharge of battery. 第 9 页

10 禁止过放电! Prohibition of overdischarge of battery. 禁止正负极短路! Prohibition of short circuit of positive and negative of battery. 请使用指定的充电器充电! Please charge by specified charger. 请不要撞击, 敲打, 钉刺或拆卸电池! Don t knock, beat, nail or disassemble battery. 请保持电芯远离热源, 禁止将电芯扔入火中! Please keep away from fire or other heating sources and prohibition of dumping of battery into fire. 使用说明 Guideline 如果电解液接触到皮肤或眼睛, 请立刻用清水冲洗接触的区域并寻求医生的建议! If electrolyte comes into contact with the skin or eyes where shall flush the electrolyte immediately with fresh water and physicians advice is to be sought. 请不要在规定的范围外使用或储存电池, 否则将削弱电池的性能, 缩短电池的寿命, 甚至导致电池发热, 起火或爆炸! Don t use or storage battery under the circumstance beyond specified, unless will weaken battery performance and shorten battery life-span, even will cause heating, fire or explosion. 使用前请确保电池在质量保证期内 Please insure battery in quality guarantee duration before using. 如果电池太脏, 使用前请清扫它们, 否则可能导致其不正常工作 If batteries are too dirty, please clean them before using. Unless will cause abnormal work of battery. 请不要使电池的封口边缘与金属直接接触 Please don't make the battery side edge of direct contact with the metal. 严禁弯折电池顶封位! It is strictly prohibited to seal a top bend batteries! 第 10 页

BPI电池规格书 mAh-加板加线-中间出线60mm-叶年鑫 _1_.doc

BPI电池规格书 mAh-加板加线-中间出线60mm-叶年鑫 _1_.doc Approval Sheet 锂离子电池规格承认书型号 Model: PL 60508 样品数量 NO.OF SAMPLES: 容量 Cap : 000mAh 送样日期 DATE OF SENDING SAMPLE: 版本 REV : A 客户代码 CUSTOMER CODE: 电芯制定人 Cell Prepared by 包装制定人 Pack Prepared by 审核人 Checked by