Microsoft Word - GEB mAh.doc

Size: px

Start display at page:

Download "Microsoft Word - GEB602030-300mAh.doc"

我湛
7 years ago
Views:

1 File No:GEB USA030 Specification For Approval 客户承认书 Model:GEB Customer( 客户名称 ): CDI Customer P/N( 客户料号 ): Revision( 版本 ): 1.00 Date( 日期 ): Comment: 意见 : Customer approval/date: 客户承认 / 日期 : Cell prepared by( 电芯制定 ) Cell checked by( 电芯审核 ) Proj. checked by( 审核 ) 杨权吴国吴富 Pack Prepared by(pack 制定 )Pack checked by(pack 审核 ) Approved by( 批准 ) 朱云罗文吴富

00 Date( 日期 ): 2014-11-10 Comment: 意见 : Customer approval/date: 客户承认 / 日期 : Cell prepared by( 电

2 AMENDMENT RECORDS 规格变更记录 Revision Description Reason for revision Date Approval 版本描述变更原因日期批准 1.00 初版发行吴富 File No: GEB USA030 Revision: 1.00 Page : 2 / 15

3 Content 目录 1.Scope 适用范围 Battery configuration 电池 Description 描述 Model 型号 Main BOM 电池主要物料 Specifications of battery 电池规格 Packaging, Storage and Transportation 包装储存及运输 Use Attentions 使用注意事项 Note 备注 Component Specification 组件规格 Cell Model 电芯规格 Specifications of cell 电芯规格 Cell Performance Criteria 电芯性能检查及测试 Appendix1 PCM parameter 附件一保护板参数 File No: GEB USA030 Revision: 1.00 Page : 3 / 15

1 Description 描述 ------------------------------------------------------------------------------------------------4 2.

4 1 Scope 适用范围 This document describes the Product Specification of the Lithium-Polymer (LIP) rechargeable battery cell supplied by General Electronics Battery Co., Ltd. 本规格说明书描述了深圳市中美通用电池有限公司 ( 以下简称中美通用 ) 生产的可充电聚合物锂离子电池的产品性能指标 2 Battery configuration 电池 2.1 Description 描述 Rechargeable Lithium-ion Polymer Battery 聚合物电池 2.2 Model 型号 GEB 红线 (P+) 黑线 (P-) -GEB602030P 3.7V 300mAh +Made in China Fig.(1)The Dimension of Battery 图 (1) 成品电池外形尺寸图 Item 项目 Description 描述 Dimension and SPEC 尺寸说明 T Thickness 电池厚度 (max) 6.20mm W Width 电池宽度 (max) 20.5mm H Height 电池高度 (max) 32.5mm -- Pack Weight 电池重量 Approx: 7.50g L Wire Length 导线长度 30±3mm File No: GEB USA030 Revision: 1.00 Page : 4 / 15

1 Description 描述 Rechargeable Lithium-ion Polymer Battery 聚合物电池 2.2 Model 型号 GEB602030 红线 (P+) 黑线 (P-) -GEB602030P 3.7V 300mAh +Made in China Fig.

5 L1 Stripping length 剥线长度 Main BOM 电池主要物料 No. Item 项目 Qty 数量 Specification 规格 1 Cell 电芯 1 Li-ion polymer cell (please check the section3) 聚合物电池 ( 见第 3 章节 ) 2 PCM 保护板 1 GEB1636 SEIKO Plate 精工板 3 Wire/connector 线材 / 连接器 1 UL1571-AWG26#,MOLEX P 2.4 Specifications of battery 电池规格 No. Items 项目 Specifications 产品规格 Charge voltage 充电电压 Nominal voltage 标称电压 Nominal capacity 标称容量 Minimal capacity 最小容量 Pack Initial Internal Impedance 电池组内阻 Charge current 充电电流 Standard Charge 标准充电 Standard Discharge 标准放电 Charging time 充电时间 Max. charge current 最大充电电流 Max. discharge current 最大放电电流 Discharge cut-off voltage 放电截止电压 Charge temperature 充电温度 Discharge temperature 放电温度 15 Temperature range for storage 储存温度范围 4.2V 3.7V 300mAh 0.2C Discharge(0.2C 放电 ) 300mAh 0.2C Discharge(0.2C 放电 ) 260mΩ Standard Charging:: 0.2 C 标准充电 : 0.2 C Rapid charge:1.0 C 快速充电 1.0 C 0.2C constant current charge to 4.2V,then constant voltage 4.2V charge till charged current declines to 0.01C 0.2 C 恒流充电至 4.2V, 再恒压 4.2V 充电直至截止电流 0.01C 0.2C constant current discharge to 3.0V 0.2C 放电至 3.0V Standard Charging: 6.0 hours (Ref.) 标准充电 : 6.0 小时 ( 参考值 ) Rapid charge: hours (Ref.) 快速充电 : 小时 ( 参考值 ) 1.0 C 1.0 C 3.0V 0 ~ ~ +55 less than 1 month 一个月以内 less than 3 month 三个月以内 -10~+55-10~+40 File No: GEB USA030 Revision: 1.00 Page : 5 / 15

器 1 UL1571-AWG26#,MOLEX51021-2P 2.4 Specifications of battery 电池规格 No.

6 less than 1 year 一年以内 0~ Packaging, Storage and Transportation 包装储存及运输 Packaging model 包装示例 : X2 Fig.(3) 图 Storage 储存 : The Li-ion battery pack should be stored in a cool, dry and well-ventilated area, and should be far from the fire and the high temperature. 锂离子电池需保存在阴凉, 干燥, 通风的环境中, 避免接触火源与热源 The battery should store in the product specification book stipulation temperature range, the best storage temp. is 25±5. The best humidity is 60±15%. 电池需按规格书规定温度范围进行储存, 最佳储存温度为 25±5, 最佳湿度为 <70% The battery should be stored within room temperature, and charged to 40%~60% electric quantity(3.85v). In order to avoid over-discharge, we suggest charge and discharge the batteries every three months. Then charge to 40%~60% electric quantity(3.85v). 电池应当在室温下存放, 应充到 40% 至 60% 的电量 (3.85V) 为防止电池过放, 建议每 3 个月按标准充放电电方式进行一次充电, 然后按标准充电方式进行充电至 40%~60% 的电量 (3.85V) Transportation 运输 File No: GEB USA030 Revision: 1.00 Page : 6 / 15

The best humidity is 60±15%. 电池需按规格书规定温度范围进行储存, 最佳储存温度为 25±5, 最佳湿度为 <70% The battery should be stored within room temperature, and charged to 40%~60% electric quantity(3.

7 Do not mix the battery products with other cargos. 请勿与其他货物混合 Do not immerse the battery products in water or allow it to get wet. 请勿将电池浸入水中或使其受潮 Do not over 7 layers staking and upside-down. 请勿叠放超过 7 层或倒置 The highest temperature in transportation is lower than 65. 最高运输温度不超过 Use Attentions 使用注意事项 To ensure proper use of the battery please read the manual carefully before using it. 为确保电池正确使用, 请在使用之前阅读使用说明书 Warnings 警告 : Do not expose to, dispose of the battery in fire. 不可将电池置于火中 Do not put the battery in a charger or equipment with wrong terminals connected. 不可将电池充电器正负极反接 Avoid shorting the battery. 不可将电池短路 Avoid excessive physical shock or vibration. 避免电池过度冲击和震荡 Do not disassemble or deform the battery. 不可拆解或扭曲电池 Do not immerse in water. 不可浸入水中 Do not use the battery mixed with other different type or model batteries. 不可将该电池与其他种类和型号的电池混用 Keep out of the reach of children. 请置于儿童接触不到的地方 File No: GEB USA030 Revision: 1.00 Page : 7 / 15

6 Use Attentions 使用注意事项 To ensure proper use of the battery please read the manual carefully before using it. 为确保电池正确使用, 请在使用之前阅读使用说明书 2.6.1 Warnings 警告 : Do not expose to, dispose of the battery in fire.

8 2.6.2 Charge 充电 : Battery must be charged in appropriate charger only. 请使用合适的充电器对电池充电 Never use a modified or damaged charger.. 请勿用返修或损坏过的充电器充电 Do not leave battery in charger over 24 hours. 请勿对电池充电 24h 以上 Charging current: Can not surpass the biggest charging current which in this specification book stipulated. 不可使用超出本规格书最大充电电流对电池进行充电 Charging voltage: Does not have to surpass the highest amount which in this specification book stipulated to decide the voltage. 充电电压 : 请不要超出本规格书所规定最高充电电压 Charge temperature: The battery must carry on the charge in the ambient temperature scope which this specification book stipulated. 充电温度 : 电池需在指定温度范围内进行充放电 Uses constant current and constant voltage way charge. PLS connect the positive and negative terminals in right way, or the battery may be damaged. 请使用恒流恒压方式进行充电请勿反接正负极, 以免损坏电池 Discharge 放电 he discharging current should not surpass the biggest discharging current this specification book stipulation, The large discharge current can cause heat and lower capacity. 放电电流不可超过规格书最大额定放电放电电流大电流会导致电池发热和容量降低 Discharge temperature: The battery discharge must carry on in the ambient temperature scope which this specification book stipulated. 放电温度 : 电池必须在规格书规定温度范围内放电 Over-discharge: After short time over discharge, then charge immediately won t damage the battery. But the battery will be damaged for being long time over discharged. During long-term storage, the battery may be within over-discharging condition for self discharge. To prevent the occurrence of over discharging, the battery should maintain the certain capacity when storage. File No: GEB USA030 Revision: 1.00 Page : 8 / 15

请勿对电池充电 24h 以上 Charging current: Can not surpass the biggest charging current which in this specification book stipulated.

9 过放电 : 电池瞬间过放然后立即充电不会损坏电池但是如果长时间过放, 电池将会被损坏在长期储存中, 可能由于电池自放电而导致电池处于过放状态因此为避免电池过放, 必须带电储存 Handling of Cell 电池操作注意事项 Soft Aluminium foil 铝箔软包 Don t strike battery with any sharp edge parts 勿用尖锐处撞击电池 Trim your nail or wear glove before taking battery 剪掉指甲, 或者戴手套 Clean worktable to make sure no any sharp particle 清理工作台, 避免尖锐零部件 Sealed edge may be damaged by heat above 100 C, bend or fold sealed edge. 封边被加热到 100 C 以上以及弯折封边都容易使封边受损 Disposal 处理措施 Regulations vary for different countries. Dispose of in accordance with local regulations. 不同国家有不同规定, 请按当地规定进行处理 Period of Warranty 保质期 The period of warranty is 12 month from the date of shipment. Guarantees to give a replacement in case of cells with defects proven due to manufacturing process instead of the customers abuse and misuse. 电池的保质期从出货之日算起为 12 个月如果证明电池的缺陷是在制造过程中形成的而不是由于用户滥用及错误使用造成, 本公司负责退换电池 2.7 Note 备注 Any other items which are not covered in this specification shall be agreed by both parties. 规格书所未包含的其它条款由双方协议解决 If the specific data or related contents you require have not shown on our datasheet, please write them in the blank of customer'comments on the datasheet cover then give feedback to our company in writing.tks. 如贵司有需要明确的参数或相关的内容, 而本规格书中又未涉及到, 请在封面的客户意见中写出并书面反馈至我司 File No: GEB USA030 Revision: 1.00 Page : 9 / 15

Clean worktable to make sure no any sharp particle 清理工作台, 避免尖锐零部件 Sealed edge may be damaged by heat above 100 C, bend or fold sealed edge.

10 Items 项目 Description 描述 Dimension and Spec 尺寸规格 3 Component Specification 组件规格 3.1 Cell Model 电芯规格 L2 B L1 L3 A L T T Thickness 厚度 6.20mm max W File No: GEB USA030 Revision: 1.00 Page : 10 / 15

11 W Width 宽度 20.5 mm max L Length 长度 mm max SPECIFICATION FOR APPROVAL Fig. cell A Sealant Length 极耳胶外露 0.2~2.0mm B Tab width 极耳宽度 2±0.1mm L1 Margins 边距 6±1.0mm L2 Margins 边距 14±1.0mm L3 极耳中心距 8±1.5mm (3)The Dimension of 图 (3) 电芯外形尺寸图 3.2 Specifications of cell 电芯规格 No Items 项目 Charge voltage 充电电压 Nominal voltage 标称电压 Nominal capacity 标称容量 Charge current 充电电流 Standard Charge 标准充电 Standard Discharge 标准放电 Charging time 充电时间 Max. charge current 最大充电电流 Max. discharge current 最大放电电流 Discharge cut-off voltage 放电截止电压 Charge temperature 充电温度 Discharge temperature 放电温度 Temperature range for storage 储存温度范围 Cell Weight 电芯重量 4.2V 3.7V Specifications 产品规格 300mAh 0.2 C Discharge 300mAh 0.2 C 放电 Standard Charging 标准充电 : 0.2 C Rapid charge 快速充电 :1.0 C 0.2C constant current charge to 4.2V,then constant voltage 4.2V charge till charged current declines to 0.01C 0.2 C 恒流充电至 4.2V, 再恒压 4.2V 充电直至截止电流 0.01C 0.2C constant current discharge to 3.0V 0.2C 放电至 3.0V Standard Charging 标准充电 : 6.0 hours (Ref.) Rapid charge 快速充电 : hours (Ref.) 1.0 C 1.0 C 3.0V 0 ~ ~ +55 less than 1 month 一个月以内 less than 3 month 三个月以内 less than 1 year 一年以内 Approx 约 :6.0g -10~+55-10~+40 0~+25 File No: GEB USA030 Revision: 1.00 Page : 11 / 15

1 2 3 4 5 6 7 8 9 10 11 12 13 14 Items 项目 Charge voltage 充电电压 Nominal voltage 标称电压 Nominal capacity 标称容量 Charge current 充电电流 Standard Charge 标准充电 Standard Discharge 标准放电 Charging

12 3.3 Cell Performance Criteria 电芯性能检查及测试 Electrical Characteristics 电性能 No. Items 项目 Test Method and Condition 测试方法和条件 Criteria 标准 Charging the cell initially with constant current at 0.2 C and 1 Standard Charge then with constant voltage at 4.2V till charge current declines to 0.01 C 标准充电方式先用 0.2 C 恒流充电至 4.2V, 再恒压 4.2V 充电直至充电电流 C First Discharge The capacity means the first discharge capacity of the cell, which is measured with discharge current of 0.2 C with 3.0V cut-off 2 Capacity 标称容量 after standard charge. 该容量是指标准充电后,0.2C 放电至 3.0V 截止所放出的容量 300mAh Initial impedance of cell 电池初始内阻 Internal resistance measured at AC 1KHz after 50% charge, at25. 在 25 环境中, 半充状态下, 测量其 AC 1KHz 下的交流阻抗 Test condition: Charge: 0.2 C to 4.2V Discharge: 0.2 C to3.0v 80% or more of 1 st cycle capacity at 0.2C discharge of Operation 测试条件 : 充电 :0.2 C 充电到 4.2V 放电 :0.2 C 放电到 3.0V 当放电容量降至初始容量的 80% 时, 所完成的循环次数定义为该电池的循环寿命 3 120mΩ 4 Cycle Life 循环寿命 300 周 (laps) Environment Characteristics 环境性能 After the standard charging, storied the cells under the condition 25.0±5.0 (Temperature) 75.0%RH(Humidity)for28 days, then measured the capacity with 0.2 C till 3.0Vwith previous standard discharge capacity of the ratio 标准充电后, 在 25 ±5 ( 温度 ) 75%RH( 湿度 ) 条件下贮存 28 天, 再以 0.2 C 放电至 3.0V 所放出的容量与前次标准放电容量的比值 1. According to item3.3.1, at 25±5. 2.Capacity comparison at each temperature, measured with constant discharge current 0.2 C with 3.0V cut-off. Percentage as an index of the capacity compared with 100% at 在 25±5 条件下, 用方法将电池充电 2. 在不同温度条件下, 用 0.2 C 的电流恒流放电至截止电压 3.0V 以 25 时放电容量为基准计算百分比 Self-discharge 荷电保持能力及恢复容量 Temperature Characteristics 温度特性 Constant humidity and temperature 恒定湿热 After standard charging, laying the battery 48h at 40±2, RH 93±2%. Recording 1C discharging time 电池标准充电后在 40±2, 相对湿度 93±2% 环境中放置 48h, 用 1C 放电至截止电压 3.0V, 记录电池放电时间 Residual capacity >90% 剩余容量 >90% -10 : 60% 25 : 100% 55 : 85% No distortion No electrolytes leakage 不变形不漏液, 放电时间 36min File No: GEB USA030 Revision: 1.00 Page : 12 / 15

2V till charge current declines to 0.01 C 标准充电方式先用 0.2 C 恒流充电至 4.2V, 再恒压 4.2V 充电直至充电电流 -- 0.

13 After standard charging, fixed the cell to vibration table and subjected to vibration cycling that the frequency is to be varied at 4 Vibration Test 振动测试 the rate of 1Hz per minute between 10Hz and 55Hz, the excursion of the vibration is 1.6mm.The cell shall be vibrated for 30 minutes per axis of XYZ axes. 将标准充电后的电池固定在振动台上, 沿 X Y Z 三个方向各振动 30 分钟, 振幅 1.6 mm, 振动频率为 10Hz~55Hz, 每分钟变化为 1Hz No leakage 无泄漏 No fire 不起火 5 Drop Test 跌落测试 The cell is to be dropped from a height of meter twice onto concrete ground. 将标准充电后的电池从 1 米高度跌落至混凝土地面 2 次 No fire, no leakage. 无起火无泄漏 Safety Characteristics 安全性能 No. Item 项目 Test Methods and Condition 测试方法和条件 Criteria 标准 At 20±5, charging batteries with constant current 1C to voltage 4.8V, then with constant voltage 4.8V till current decline to 0A. Stop test till 1 Over charge testing 过充测试 batteries temperature 10 lower than max temperature. 在 20±5 状态下, 电芯用 1C 电流充电至 4.8V, 然后恒压 4.8V 让电流下降接近 0A, 监视电池温度变化, 当电池温度下降一峰值低约 10 时, 停止实验. No fire or explosion 不起火, 不爆炸 At 20±5, After standard charging, connect batteries anode and cathode by wire which 2 Short-circuit testing 短路测试 impedance less than 50mΩ, Stop test till batteries temperature 10 lower than max temperature. 在 20±5 状态下, 标准充电后, 将电芯的正负极用一根小于 50mΩ 的导线连接, 监视电芯温度变化, 当电池温度下降到比峰值低约 10, 结束试验. No fire or explosion. 不起火, 不爆炸 Put the Cell in a circulating air oven, at a rate of (5 3 Heating 热冲击 ±2 ) per minute to 130,and then placed fou 30 cminute at 130. 电池放置于热箱中, 温度以 (5 ±2 ) / 分钟的频率加热到 130 并保持 30 分钟 No explosion, no fire; 不爆炸, 不起火 ; Note 测试备注 Visual inspection 外观检查 There shall be no such defect as scratch, flaw, crack, and leakage, which may adversely affect commercial File No: GEB USA030 Revision: 1.00 Page : 13 / 15

6 mm, 振动频率为 10Hz~55Hz, 每分钟变化为 1Hz No leakage 无泄漏 No fire 不起火 5 Drop Test 跌落测试 The cell is to be dropped from a height of meter twice onto concrete ground.

14 value of the cell. 不允许有任何影响电池性能的外观缺陷, 诸如裂纹裂缝泄漏等 Standard environmental test condition 标准测试环境 Unless otherwise specified, all tests stated in this Product Specification are conducted at below condition: Temperature: 25.0±5.0 Humidity: 75.0%RH 除非特别说明, 本标准书中所有测试均在以下环境条件下进行 : 温度 :25.0±5.0 湿度 : 75.0%RH Above testing of safe characteristic must be with protective equipment. 安全性能测试应在有保护措施下进行 Appendix1 PCM parameter 保护板参数 1. Parameter 参数 Item 项目 Symbol 符号 Content 详细内容 Criteria 标准 Over charge Protection 过充保护 Over discharge 过放保护 Over current protection 过流保护 V DET1 tv DET1 V REL1 V DET2 tv DET2 V REL2 V DET3 I DP tv DET3 Over charge detection voltage 过充电检测电压 Over charge detection delay time 过充电检测延迟时间 Over charge release voltage 过充电解除电压 Over discharge detection voltage 过放电检测电压 Over discharge detection delay time 过放电检测延迟时间 Over discharge release voltage 过放电解除电压 Over current detection voltage 过电流检测电压 Over current detection current 过电流保护电流 Detection delay time 检测延迟时间 Release condition 保护解除条件 Detection condition 保护条件 4.28V±0.035V 1.4s(MAX) 4.08±0.1V 3.0V±0.08V 173ms(MAX) Charging to 3.0V lifted above 充电至 3.0V 以上解除 MIN:1.2A 80mV±15mV MAX:2.8A 11ms(MAX) Cut load 断开负载 Exterior short circuit 外部电路短路 Short protection 短路保护 T SHORT Detection delay time 检测延迟时间 Release condition 保护解除条件 0.5ms(MAX) Cut short circuit 断开短路电路 File No: GEB USA030 Revision: 1.00 Page : 14 / 15

0%RH 除非特别说明, 本标准书中所有测试均在以下环境条件下进行 : 温度 :25.0±5.0 湿度 : 75.0%RH 3.3.4.3 Above testing of safe characteristic must be with protective equipment.

15 Interior resistance 内阻 R DS Main loop electrify resistance(battery Vol=3.9V) 主回路通态电阻 ( 电池电压 =3.9V) B- 至 P- B - to P- R DS 60mΩ Current consumption 消耗电流 I DD Current consume in normal operation 工作时电路内部消耗 MIN:0.3μA MAX:8.0μA Battery Vo1=0V charge 向 0V 电池充电的功能 / YES 允许 2. Application Schematic 应用原理图 3. PCB Dimensions PCB 板图纸顶层 Top: 底层 Bottom: File No: GEB USA030 Revision: 1.00 Page : 15 / 15

路内部消耗 MIN:0.3μA MAX:8.0μA Battery Vo1=0V charge 向 0V 电池充电的功能 / YES 允许 2.

评委 : 徐岩宇 - 个人技术标资信标初步审查明细表序号投标单位投标函未按招标文件规定填写漏填或内容填写错误的 ; 不同投标人的投标文件由同一台电脑或同一家投标单

评委 : 徐岩宇 - 个人技术标资信标初步审查明细表序号投标单位投标函未按招标文件规定填写漏填或内容填写错误的 ; 不同投标人的投标文件由同一台电脑或同一家投标单评委 : 徐岩宇 - 个人清标评审明细表评审因素序号投标单位清标评审 1 深圳市创捷科技有限合格 2 四川川大智胜软件股份有限合格 3 北京航天长峰科技工业集团有限公司合格 4 深圳中兴力维技术有限合格 5 深圳键桥通讯技术股份有