of the constructed prototype at 5800 MHz (center frequency of the 5.8-GHz band), and similar directional radiation patterns are also obtained. Figure 5 shows the measured peak antenna gain for operating frequencies across the 5.2- and 5.8-GHz bands. A stable antenna gain of about 5.5 6.0 dbi is obtained. 4. CONCLUSION A planar folded-dipole antenna printed on a dielectric substrate and comprising two back-to-back folded dipoles for spatial-diversity operation in WLAN communications has been proposed. A prototype with a wide impedance bandwidth of about 1 GHz covering the 5.2- and 5.8-GHz bands for WLAN operation has been successfully implemented, and good directional radiation patterns covering two complementary half spaces have been obtained, which makes the antenna capable of performing spatial diversity to combat the multipath interference problem and enhance the system s performance. REFERENCES 1. G. Johnson and D. Keilen, Diversity antenna system for LAN communication system, U.S. Patent No. 6339404 B1, 2002. 2. G.Y. Lee, H.T. Chen, and K.L. Wong, Dual-band printed diversity dipole antenna for WLAN access point, Microwave Opt Technol Lett 36 (2003), 254 257. 3. W.L. Stutzman and G.A. Thiele, Antenna theory and design, 2 nd ed., Wiley, New York, 1998, Ch. 5. 2003 Wiley Periodicals, Inc. A STAIR-SHAPED SLOT ANTENNA FOR THE TRIPLE-BAND WLAN APPLICATIONS Figure 2 Comparison of the simulated and measured return loss of the stair-shaped slot antenna with four stubs at the slot edge slot antenna is smaller than that of the conventional rectangular-slot antenna. 2003 Wiley Periodicals, Inc. Microwave Opt Technol Lett 39: 370 372, 2003; Published online in Wiley InterScience (www. interscience.wiley.com). DOI 10.1002/mop.11220 Key words: slot antenna; WLAN; multiple-band antenna 1. INTRODUCTION The advantages of the microstrip-fed slot antenna over the patch antenna are wider bandwidth, less conductor loss, and better isolation between the radiating element and feeding network [1]. These advantages have prompted the extensive use of the slot antenna in radar and communications systems. The detailed char- Chien-Jen Wang and Wen-Tsai Tsai Department of Electrical Engineering Feng-Chia University Taichung, Taiwan, R.O.C. Received 16 May 2003 ABSTRACT: In this paper, a novel triple-band microstrip-fed slot antenna for wireless communication systems operating at 2.4, 5.2, and 5.8 GHz is demonstrated. The slot antenna is originally designed to radiate at 2.4 GHz. By etching a stair-shaped slot on the ground plane and adding several stubs at the edge to excite the first higher-order mode, we can create another resonant band at 5 GHz. According to the results, the impedance bandwidths are 227 and 778 MHz at the 2.4- and 5-GHz bands, respectively. In addition, the dimension of the proposed Figure 1 Schematic diagram of the stair-shaped slot antenna with four stubs at the slot edge Figure 3 Comparison of G vs. the measured resonant frequencies of the modified stair-shaped slot antenna 370 MICROWAVE AND OPTICAL TECHNOLOGY LETTERS / Vol. 39, No. 5, December 5 2003
Figure 4 Comparison of S vs. the measured resonant frequencies of the modified stair-shaped slot antenna acteristics of the fundamental mode and the first higher-order mode of the microstrip-fed slot antenna are presented by using the reciprocity theorem in a manner similar to the analysis of the waveguide [2, 3]. The slot length of the slot antenna is usually designed to be g / 2, where g is the guided wavelength of the operating frequency. Here, we present a stair-shaped slot antenna with several matching stubs at the slot edge. The capactive coupling between the microstrip feedline and the slot edges can enhance the impedance bandwidth, and two neighboring stubs at the slot edge can lower the higher resonant band in order to meet the requirements of 5.2 5.8-GHz band wireless communication systems. 2. ANTENNA DESIGN The schematic configuration of the stair-shaped slot antenna with four stubs is shown in Figure 1. FR-4 was used as a substrate with a dielectric constant of 4.4 and thickness of 0.8 mm. A stair-shaped slot was etched on the ground plane of the substrate as the radiating element. The width of the microstrip feed line on the bottom plane of the substrate, used for the probe excitation of the slot antenna, is 1.4 mm and the characteristic impedance is 52 at 2.4 GHz. The capacitive coupling between the microstrip feed line and the two slot edges leads to improved impedance characteristics. Four tuning stubs are symmetrically added at both edges of the stair-shaped slot to excite the first-order mode. The position G of the stub was located at an offset of 1.75 mm from the sidewall of the slot and the separation S of the stub was 1 mm. This separation between two neighboring stubs was tested to modify the impedance characteristics so that the initial frequency of the higher resonant band could be reduced. Figure 5 Simulated and measured radiation patterns of the E and H planes of the proposed slot antenna at 2.45, 5.20, and 5.80 GHz MICROWAVE AND OPTICAL TECHNOLOGY LETTERS / Vol. 39, No. 5, December 5 2003 371
3. SIMULATED AND MEASURED RESULTS Figure 2 shows the comparison of the simulated and measured return losses of the stair-shaped slot antenna with four stubs, made by utilizing the commercial simulation tool Ansoft HFSS V8.0 and an HP 8510C network analyzer. Figures 3 and 4 show the comparison of the stub location G or the stub separation S versus the measured resonant frequencies of the modified stair-shaped slot antenna. It is found that the operating frequencies of the lower and higher resonant bands are reduced when G increases and the higher resonant band of the slot antenna is lowered when S decreases. Two neighboring stubs can be treated as a capacitor and the loading effect due to the capacitive coupling enhances the matching condition. The measured results indicate that the lower resonant band of the proposed slot antenna ranges from 2.337 to 2.614 GHz and the higher resonant band achieves the bandwidth from 5.124 to 5.902 GHz. Figure 5 presents the simulated and measured radiation patterns of the E and H planes of the slot antenna at 2.45, 5.20, and 5.80 GHz. The beam positions of the maximum power of the slot antenna are not located in the broadside direction due to the nonrectangular slot. By applying the techniques described in this paper, the slot width is also reduced to be 32.75 mm less than 34.3 mm ( g / 2) at 2.45 GHz. The size of the slot antenna is reduced by approximately 5%. The proposed slot antenna can be a candidate for the Tx/Rx antenna of portable devices, such as notebooks, tablet PCs, or PDAs. ACKNOWLEDGMENTS This work is currently supported by the National Science Council, Taiwan, under grants NSC 91-2213-E-035-037 and NSC 91-2218- E-035-006. The authors would like to thank Prof. Rey-Bin Huang, National Chi-Nan University, Nantou, for providing equipment for the measurements used in this paper. The authors would also like to thank the National Center for High Performance Computing, Hsinchu, Taiwan, for their contribution of the Ansoft HFSS V 8.0 simulation tool. REFERENCES 1. H.G. Akhavan and D.M. Syahkal, Study of coupled slot antennas fed by microstrip lines, 10 th Int Conf Antennas Propagat, 1997, pp. 1290 1292. 2. D.M. Pozar, A reciprocity method of analysis for printed slot and slot-coupled microstrip antenna, IEEE Trans Antennas Propagat 34 (1986), 1439 1446. 3. M. Omiya, T. Hikage, N. Ohno, K. Horiguchi, and K. Itoh, Design of cavity-back slot antennas using the finite-difference time-domain technique, IEEE Trans Antennas Propagat 46 (1998), 1853 1858. 2003 Wiley Periodicals, Inc. Figure 5 Continued 372 MICROWAVE AND OPTICAL TECHNOLOGY LETTERS / Vol. 39, No. 5, December 5 2003
易迪拓培训 专注于微波 射频 天线设计人才的培养网址 :http://www.edatop.com 射频和天线设计培训课程推荐 易迪拓培训 (www.edatop.com) 由数名来自于研发第一线的资深工程师发起成立, 致力并专注于微波 射频 天线设计研发人才的培养 ; 我们于 2006 年整合合并微波 EDA 网 (www.mweda.com), 现已发展成为国内最大的微波射频和天线设计人才培养基地, 成功推出多套微波射频以及天线设计经典培训课程和 ADS HFSS 等专业软件使用培训课程, 广受客户好评 ; 并先后与人民邮电出版社 电子工业出版社合作出版了多本专业图书, 帮助数万名工程师提升了专业技术能力 客户遍布中兴通讯 研通高频 埃威航电 国人通信等多家国内知名公司, 以及台湾工业技术研究院 永业科技 全一电子等多家台湾地区企业 易迪拓培训课程列表 :http://www.edatop.com/peixun/rfe/129.html 射频工程师养成培训课程套装该套装精选了射频专业基础培训课程 射频仿真设计培训课程和射频电路测量培训课程三个类别共 30 门视频培训课程和 3 本图书教材 ; 旨在引领学员全面学习一个射频工程师需要熟悉 理解和掌握的专业知识和研发设计能力 通过套装的学习, 能够让学员完全达到和胜任一个合格的射频工程师的要求 课程网址 :http://www.edatop.com/peixun/rfe/110.html ADS 学习培训课程套装该套装是迄今国内最全面 最权威的 ADS 培训教程, 共包含 10 门 ADS 学习培训课程 课程是由具有多年 ADS 使用经验的微波射频与通信系统设计领域资深专家讲解, 并多结合设计实例, 由浅入深 详细而又全面地讲解了 ADS 在微波射频电路设计 通信系统设计和电磁仿真设计方面的内容 能让您在最短的时间内学会使用 ADS, 迅速提升个人技术能力, 把 ADS 真正应用到实际研发工作中去, 成为 ADS 设计专家... 课程网址 : http://www.edatop.com/peixun/ads/13.html HFSS 学习培训课程套装该套课程套装包含了本站全部 HFSS 培训课程, 是迄今国内最全面 最专业的 HFSS 培训教程套装, 可以帮助您从零开始, 全面深入学习 HFSS 的各项功能和在多个方面的工程应用 购买套装, 更可超值赠送 3 个月免费学习答疑, 随时解答您学习过程中遇到的棘手问题, 让您的 HFSS 学习更加轻松顺畅 课程网址 :http://www.edatop.com/peixun/hfss/11.html `
易迪拓培训 专注于微波 射频 天线设计人才的培养网址 :http://www.edatop.com CST 学习培训课程套装该培训套装由易迪拓培训联合微波 EDA 网共同推出, 是最全面 系统 专业的 CST 微波工作室培训课程套装, 所有课程都由经验丰富的专家授课, 视频教学, 可以帮助您从零开始, 全面系统地学习 CST 微波工作的各项功能及其在微波射频 天线设计等领域的设计应用 且购买该套装, 还可超值赠送 3 个月免费学习答疑 课程网址 :http://www.edatop.com/peixun/cst/24.html HFSS 天线设计培训课程套装套装包含 6 门视频课程和 1 本图书, 课程从基础讲起, 内容由浅入深, 理论介绍和实际操作讲解相结合, 全面系统的讲解了 HFSS 天线设计的全过程 是国内最全面 最专业的 HFSS 天线设计课程, 可以帮助您快速学习掌握如何使用 HFSS 设计天线, 让天线设计不再难 课程网址 :http://www.edatop.com/peixun/hfss/122.html 13.56MHz NFC/RFID 线圈天线设计培训课程套装套装包含 4 门视频培训课程, 培训将 13.56MHz 线圈天线设计原理和仿真设计实践相结合, 全面系统地讲解了 13.56MHz 线圈天线的工作原理 设计方法 设计考量以及使用 HFSS 和 CST 仿真分析线圈天线的具体操作, 同时还介绍了 13.56MHz 线圈天线匹配电路的设计和调试 通过该套课程的学习, 可以帮助您快速学习掌握 13.56MHz 线圈天线及其匹配电路的原理 设计和调试 详情浏览 :http://www.edatop.com/peixun/antenna/116.html 我们的课程优势 : 成立于 2004 年,10 多年丰富的行业经验, 一直致力并专注于微波射频和天线设计工程师的培养, 更了解该行业对人才的要求 经验丰富的一线资深工程师讲授, 结合实际工程案例, 直观 实用 易学 联系我们 : 易迪拓培训官网 :http://www.edatop.com 微波 EDA 网 :http://www.mweda.com 官方淘宝店 :http://shop36920890.taobao.com 专注于微波 射频 天线设计人才的培养易迪拓培训官方网址 :http://www.edatop.com 淘宝网店 :http://shop36920890.taobao.com