Hybrid of Monopole and Dipole Antennas for Concurrent 2.4- and 5-GHz WLAN Access Point

Hybrid of Monopole and Dipole Antennas for Concurrent 2.4- and 5-GHz WLAN Access Point Saou-Wen Su 1, Jui-Hung Chou 2 Network Access Strategic Business Unit Lite-On Technology Corp., No. 9, Chien I Road, Chungho, Taipei County 23585, Taiwan 1 stephen.su@liteon.com 2 alex.chou@liteon.com Abstract A novel hybrid of a 2.4-GHz monopole antenna and a 5-GHz dipole antenna is presented to provide concurrent 2.4 and 5 GHz band operation for access-point applications. The two antennas are arranged in a collinear structure and printed on a compact dielectric substrate with dimensions 12 mm 60 mm. The monopole antenna has a meandered radiating strip and is short-circuited to a small ground plane through a shorting strip. The dipole antenna includes two sub-dipoles at the opposite side of a narrow ground plane and fed by a simple T-junction microstrip-line network. The two antennas are closely set with a distance of 1 mm only, yet good port isolation (S 21 ) well below 20 db can be obtained. With a low profile, the proposed design can easily fit into the casing of some standard access points and allow the 2.4 and 5 GHz band signals to be simultaneously received or transmitted with no external diplexer required. Good omnidirectional radiation has been observed too. I. INTRODUCTION With a great success in developing WLAN technology over the past few years, many Wi-Fi-enabled consumer-electronic devices are ubiquitous in the market, along with pervasive wireless access-point (AP) infrastructure. The laptops nowadays are almost equipped with 802.11a/b/g wireless functionality as a basic, required specification. For indoor access-point applications, several printed antennas have been reported to cover single- or dual-band WLAN operation in the 2.4 GHz (2400-2484 MHz) band and/or 5 GHz [5.2 GHz (5150-5350)/5.8 GHz (5725-5825 MHz)] band [1-6]. Among these designs, the dual-band antenna usually has a single RF feed port only. This suggests that an extra external diplexer between the conventional single-feed antenna and two separate 2.4 and 5 GHz modules is needed when concurrent 2.4 and 5 GHz operation is demanded for the purpose of having more efficient spectrum usage. However, even a good diplexer can still yield 1-dB insertion loss over the 2.4 and 5 GHz bands, which is really unsatisfying and unwanted. Recently, the integration of two individual antennas with two separate feeds has been introduced as a good solution to concurrent operation [7, 8]. The 2.4 GHz antenna and the 5 GHz antenna can be integrated into a compact structure by employing a common shorting portion [7] or sharing a common antenna ground plane [7, 8] with port isolation below 15 db. In this paper, we propose a novel design of a hybrid of printed monopole and dipole antennas for concurrent, WLAN access-point applications. Each of the two antennas has its own radiating element and ground plane, different from the antenna configuration shown in [7, 8], in which the two antennas share the same ground plane. The two antennas in this study are arranged in a collinear structure, the monopole at the top of the dipole, to achieve an upright but narrow profile to fit into the casing of an access point. Though there is only 1 mm small gap between the two antennas, low mutual coupling with good port isolation (S 21 < 20 db) can still be obtained. Details of the design consideration of the proposed antenna are described in this article, and the experimental results of a realized prototype are presented and discussed. II. ANTENNA DESIGN Fig. 1(a) shows the proposed hybrid of the 2.4 GHz monopole and the 5 GHz dipole antennas for access-point applications. The two-antenna system is formed on a 0.8-mm thick FR4 substrate with dimensions 12 mm 60 mm. The two antennas are arranged in a collinear structure, in which the monopole is located at the top of the dipole, and there is only 1 mm isolation gap therein between. Further detailed dimensions of each antenna are shown in Fig. 1(b). The monopole antenna in the upper part has a small ground plane of size 12 mm 15.5 mm and an S-shaped radiating strip, which is further short-circuited to the ground through a thin shorting strip. The shorting strip has been meandered such that better impedance matching can be realized. As for the dipole antenna in the lower part, the antenna consists of two subdipoles at the opposite side of a narrow ground of width 4 mm. This back-to-back dipole configuration [2, 4] can result in good omnidirectional radiation characteristics. Notice that the ground plane is set on the same layer where the printed monopole antenna is located. The dipole arms are printed on both sides of the substrate. To excite both the sub-dipoles with equal power and in phase, a simple T-junction 50-Ω microstrip-line network is utilized in this study. To feed the design prototype, two short, 50-Ω mini-coaxial cables with I-PEX connectors are used. The inner conductors of the coaxial cables are connected to feed point A and C, and the outer braided shielding are connected to ground point B and D. Because the unwanted leakage currents on the surface of the coaxial cable usually occur, the cable routing of the monopole antenna thus needs more concern. For minimizing this cable effect, the coaxial cable is arranged to first go through the monopole ground and then the center of the dipole ground [see photo of a manufacture sample in Fig. 2(a)]. In this 545

case, both the antennas can be fed at or below the end of the two-antenna system, making it possible for very practical applications in some swivel-type access point, as seen in an example photo in Fig. 2(b). Also notice that the two coaxial cables in the two-antenna system can affect the mutual coupling between the antennas. The results of measured isolation (S 21 ) may be inaccurate if no special consideration is given for cable routing. (a) (a) (b) Fig. 2 (a) Photo of the proposed antennas printed on a double-layered FR4 substrate and fed by two 50-Ω mini-coaxial cables. (b) Photo of a swivel-type access point. (b) Fig. 1 (a) Configuration of the proposed hybrid of the 2.4-GHz monopole and 5-GHz dipole antennas for a concurrent WLAN access point. (b) Detailed dimensions of the two printed WLAN antennas. III. EXPERIMENTAL RESULTS AND DISCUSSION Fig. 3(a) and 3(b) show the measured and simulated reflection coefficients (S 11 for the 2.4 GHz antenna, S 22 for the 5 GHz antenna) and isolation (S 21 ) of a design prototype. The experimental data in general compare well with the simulation results, which are based on the finite element method (FEM). Some discrepancies are also found due to manufacture tolerance and effect of mini-coaxial cables. The measured impedance bandwidth, defined by 10 db return loss, can easily meet the bandwidth specification for 2.4 and 5 GHz WLAN operation and the isolation between the antennas is well below 20 db. The isolation is even better than 30 db in the 5 GHz band. Notice that when there is no distance [that s gap equal to 0 in Fig.1(a)] between the two antennas, the isolation behavior in both resonant modes is seen from the simulation results (not shown here for brevity) to rapidly deteriorate by about 10 db. Fig. 4 and 5 give the far-field, 2-D radiation patterns in E θ and E ϕ fields at 2442 and 5490 MHz, the center operating frequencies of the 2.4 and 5 GHz bands. Other frequencies in the bands of interest were also measured, and no appreciable 546

difference in radiation patterns was obtained. It is easy to see that good omnidirectional radiation patterns in the horizontal plane (that s the x-y plane here) are obtained from the test results. Notice that though the monopole antenna is utilized for 2.4 GHz operation, the antenna system (radiating strip and ground plane thereof) can radiate a dipole-like radiation pattern. This is because both the radiating strip and the ground plane are of quarter-wavelength resonant structure with no null surface currents occurring in both portions at the same operating frequency. Fig. 6 plots the measured peak antenna gain and radiation efficiency. The peak-gain level in the 2.4 GHz band is about 2.1 dbi; the radiation efficiency exceeds about 83%. As for the 5.2 GHz band, the peak gain is in the range of 2.6-3.1 dbi with radiation efficiency larger than 79%. Notice that the radiation efficiency was obtained in the 3-D test system by calculating the total radiated power of an antenna under test (AUT) over the 3-D spherical radiation first and then dividing the total amount by the input power (default value is 0 dbm) given to the AUT. Fig. 4 Measured 2-D radiation patterns at 2442 MHz for the antenna studied in Fig 3(a). (a) Fig. 5 Measured 2-D radiation patterns at 5490 MHz for the antenna studied in Fig 3(a). (b) Fig. 3 Reflection coefficients (S 11 for the 2.4 GHz antenna, S 22 for the 5 GHz antenna) and isolation (S 21 ) between the two antennas: (a) measured results; (b) simulated results. Fig. 6 Measured peak antenna gain and radiation efficiency for the two antennas studied in Fig. 3(a). 547

IV. CONCLUSIONS A two-antenna system formed by arranging a monopole antenna and a dipole antenna both printed on a dielectric substrate for concurrent, WLAN access-point applications has been demonstrated, studied, and tested. The results show that though the distance between the two WLAN antennas is 1 mm, good isolation of less than 20 db over the 2.4 and 5 GHz bands is still obtained. In addition, dipole-like radiation patterns with good omnidirectional radiation in the horizontal plane have been observed. Peak antenna gain is about 2.1 and 2.9 dbi for the 2.4 and 5 GHz antennas respectively. The proposed design is well suited for concurrent 2.4 and 5 GHz band operation in an access point, which does not lose extra gain compared with the case of a single-feed, dual-band access point using an external diplexer for concurrent operation. REFERENCES [1] S. W. Su, Y. T. Chen, and K. L. Wong, Printed dual-band U-slotted monopole antenna for WLAN access point, Microwave Opt. Technol. Lett., vol. 38, pp. 436 439, Sep. 2003. [2] K. L. Wong, J. W. Lai, and F. R. Hsiao, Omnidirectional planar dipole-array antenna for 2.4/5.2-GHz WLAN access points, Microwave Opt. Technol. Lett., vol. 39, pp. 33 36, Oct. 2003. [3] K. M. Luk and S. H. Wong, A printed high-gain monopole antenna for indoor wireless LANs, Microwave Opt. Technol. Lett., vol. 41, pp. 177 180, May 2004. [4] F. R. Hsiao and K. L. Wong, Omnidirectional planar folded dipole antenna, IEEE Trans. Antennas Propagat., vol. 52, pp. 1898 1902, Jul. 2004. [5] R. Bancroft, Design parameters of an omnidirectional planar microstrip antenna, Microwave Opt. Technol. Lett., vol. 47, pp. 414 418, Dec. 2005. [6] S. W. Su and J. H. Chou, Printed omnidirectional access-point antenna for 2.4/5-GHz WLAN operation, Microwave Opt. Technol. Lett., vol. 50, pp. 2403 2407, Sep. 2008. [7] K. L. Wong and J. H. Chou, Integrated 2.4- and 5-GHz WLAN antennas with two isolated feeds for dual-module applications, Microwave Opt. Technol. Lett., vol. 47, pp. 263 265, Nov. 2005. [8] S. W. Su, J. H. Chou, and Y. T. Liu, Printed coplanar two-antenna element for 2.4/5 GHz WLAN operation in a MIMO system, Microwave Opt. Technol. Lett., vol. 50, pp. 1635 1638, Jun. 2008. 548

易迪拓培训 专注于微波 射频 天线设计人才的培养网址 :http://www.edatop.com 射频和天线设计培训课程推荐 易迪拓培训 (www.edatop.com) 由数名来自于研发第一线的资深工程师发起成立, 致力并专注于微波 射频 天线设计研发人才的培养 ; 我们于 2006 年整合合并微波 EDA 网 (www.mweda.com), 现已发展成为国内最大的微波射频和天线设计人才培养基地, 成功推出多套微波射频以及天线设计经典培训课程和 ADS HFSS 等专业软件使用培训课程, 广受客户好评 ; 并先后与人民邮电出版社 电子工业出版社合作出版了多本专业图书, 帮助数万名工程师提升了专业技术能力 客户遍布中兴通讯 研通高频 埃威航电 国人通信等多家国内知名公司, 以及台湾工业技术研究院 永业科技 全一电子等多家台湾地区企业 易迪拓培训课程列表 :http://www.edatop.com/peixun/rfe/129.html 射频工程师养成培训课程套装该套装精选了射频专业基础培训课程 射频仿真设计培训课程和射频电路测量培训课程三个类别共 30 门视频培训课程和 3 本图书教材 ; 旨在引领学员全面学习一个射频工程师需要熟悉 理解和掌握的专业知识和研发设计能力 通过套装的学习, 能够让学员完全达到和胜任一个合格的射频工程师的要求 课程网址 :http://www.edatop.com/peixun/rfe/110.html ADS 学习培训课程套装该套装是迄今国内最全面 最权威的 ADS 培训教程, 共包含 10 门 ADS 学习培训课程 课程是由具有多年 ADS 使用经验的微波射频与通信系统设计领域资深专家讲解, 并多结合设计实例, 由浅入深 详细而又全面地讲解了 ADS 在微波射频电路设计 通信系统设计和电磁仿真设计方面的内容 能让您在最短的时间内学会使用 ADS, 迅速提升个人技术能力, 把 ADS 真正应用到实际研发工作中去, 成为 ADS 设计专家... 课程网址 : http://www.edatop.com/peixun/ads/13.html HFSS 学习培训课程套装该套课程套装包含了本站全部 HFSS 培训课程, 是迄今国内最全面 最专业的 HFSS 培训教程套装, 可以帮助您从零开始, 全面深入学习 HFSS 的各项功能和在多个方面的工程应用 购买套装, 更可超值赠送 3 个月免费学习答疑, 随时解答您学习过程中遇到的棘手问题, 让您的 HFSS 学习更加轻松顺畅 课程网址 :http://www.edatop.com/peixun/hfss/11.html `

易迪拓培训 专注于微波 射频 天线设计人才的培养网址 :http://www.edatop.com CST 学习培训课程套装该培训套装由易迪拓培训联合微波 EDA 网共同推出, 是最全面 系统 专业的 CST 微波工作室培训课程套装, 所有课程都由经验丰富的专家授课, 视频教学, 可以帮助您从零开始, 全面系统地学习 CST 微波工作的各项功能及其在微波射频 天线设计等领域的设计应用 且购买该套装, 还可超值赠送 3 个月免费学习答疑 课程网址 :http://www.edatop.com/peixun/cst/24.html HFSS 天线设计培训课程套装套装包含 6 门视频课程和 1 本图书, 课程从基础讲起, 内容由浅入深, 理论介绍和实际操作讲解相结合, 全面系统的讲解了 HFSS 天线设计的全过程 是国内最全面 最专业的 HFSS 天线设计课程, 可以帮助您快速学习掌握如何使用 HFSS 设计天线, 让天线设计不再难 课程网址 :http://www.edatop.com/peixun/hfss/122.html 13.56MHz NFC/RFID 线圈天线设计培训课程套装套装包含 4 门视频培训课程, 培训将 13.56MHz 线圈天线设计原理和仿真设计实践相结合, 全面系统地讲解了 13.56MHz 线圈天线的工作原理 设计方法 设计考量以及使用 HFSS 和 CST 仿真分析线圈天线的具体操作, 同时还介绍了 13.56MHz 线圈天线匹配电路的设计和调试 通过该套课程的学习, 可以帮助您快速学习掌握 13.56MHz 线圈天线及其匹配电路的原理 设计和调试 详情浏览 :http://www.edatop.com/peixun/antenna/116.html 我们的课程优势 : 成立于 2004 年,10 多年丰富的行业经验, 一直致力并专注于微波射频和天线设计工程师的培养, 更了解该行业对人才的要求 经验丰富的一线资深工程师讲授, 结合实际工程案例, 直观 实用 易学 联系我们 : 易迪拓培训官网 :http://www.edatop.com 微波 EDA 网 :http://www.mweda.com 官方淘宝店 :http://shop36920890.taobao.com 专注于微波 射频 天线设计人才的培养易迪拓培训官方网址 :http://www.edatop.com 淘宝网店 :http://shop36920890.taobao.com