When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X notch"(show below), please make sure your AGP card is AGP 4X (1.5V). Do not use AGP 2X card (3.3V) in this motherboard. It will burn and damage the motherboard due to Intel 845 chipset can't support AGP 2X(3.3V).. Example 1: Diamond Vipper V770 golden finger is compatible with 2X/ 4X mode AGP slot. It can be switched between AGP 2X(3.3V) or 4X(1. 5V) mode by adjusting the jumper. The factory default for this card is 2X (3.3V). If you install this card in GA-8IRM series (or any AGP 4X only) motherboards without switching the jumper to 4X mode (1.5V), it will burn the motherboard. Example 2: ATi Rage 128 Pro (Power Color)& SiS 305 golden finger is compatible with 2X/4X mode AGP slot, but it supports 2X(3.3V) only. If you install this card in GA-8IRM series (or any AGP 4X only) motherboards, it will burn the motherboard. Note : Although Gigabyte's AG32S graphics card is based on ATi Rage 128 Pro chip, the design of AG32S is compliance with AGP 4X (1.5V) specification. Therefore, AG32S will work fine with Intel 845 / 850 based motherboards.
The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a commitment to up date the information contained herein. Third-party brands and names are the property of their respective owners. Please do not remove any labels on motherboard, this may void the warranty of this motherboard. Due to rapid change in technology, some of the specifications might be out of date before publication of this booklet.
Declaration of Conformity We, Manufacturer/Importer (full address) G.B.T. Technology Träding GMbH Ausschlager Weg 41, 1F, 20537 Hamburg, Germany declare that the product ( description of the apparatus, system, installation to which it refers) Mother Board GA-8IRM/GA-8IRML is in conformity with (reference to the specification under which conformity is declared) in accordance with 89/336 EEC-EMC Directive EN 55011 Limits and methods of measurement of radio disturbance characteristics of industrial,scientific and medical (ISM high frequency equipment EN 61000-3-2* EN 60555-2 Disturbances in supply systems cause by household appliances and similar electrical equipment Harmonics EN 55013 Limits and methods of measurement of radio disturbance characteristics of broadcast receivers and associated equipment EN 61000-3-3* EN 60555-3 Disturbances in supply systems cause by household appliances and similar electrical equipment Voltage fluctuations EN 55014 EN 55015 Limits and methods of measurement of radio disturbance characteristics of household electrical appliances, portable tools and similar electrical apparatus Limits and methods of measurement of radio disturbance characteristics of fluorescent lamps and luminaries EN 50081-1 Generic emission standard Part 1: Residual commercial and light industry EN 50082-1 Generic immunity standard Part 1: Residual commercial and light industry EN 55081-2 Generic emission standard Part 2: Industrial environment EN 55020 Immunity from radio interference of broadcast receivers and associated equipment EN 55082-2 Generic emission standard Part 2: Industrial environment EN 55022 Limits and methods of measurement of radio disturbance characteristics of information technology equipment ENV 55104 lmmunity requirements for household appliances tools and similar apparatus DIN VDE 0855 part 10 part 12 Cabled distribution systems; Equipment for receiving and/or distribution from sound and television signals EN50091-2 EMC requirements for uninterruptible power systems (UPS) CE marking (EC conformity marking) The manufacturer also declares the conformity of above mentioned product with the actual required safety standards in accordance with LVD 73/23 EEC EN 60065 EN 60335 Safety requirements for mains operated electronic and related apparatus for household and similar general use Safety of household and similar electrical appliances EN 60950 EN 50091-1 Manufacturer/Importer (Stamp) Date : Nov. 10, 2001 Signature: Name: Timmy Huang Timmy Huang
DECLARATION OF CONFORMITY Per FCC Part 2 Section 2.1077(a) Responsible Party Name: G.B.T. INC. (U.S.A.) Address: 17358 Railroad Street City of Industry, CA 91748 Phone/Fax No: (818) 854-9338/ (818) 854-9339 hereby declares that the product Product Name: Motherboard Model Number: GA-8IRM/GA-8IRML Conforms to the following specifications: FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109 (a),class B Digital Device Supplementary Information: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful and (2) this device must accept any inference received, including that may cause undesired operation. Representative Person s Name: ERIC LU Signature: Eric Lu Date: Nov. 10,2001
GA-8IRM P4 DDR Pentium 4 Rev. 2.2 First Edition 12MC-8IRM-2201
GA-8IRM... 4... 4... 5... 6... 6 GA-8IRM Layout... 8... 9 1: (CPU)... 10...10... 11 2 :... 12 3:... 13 4 : 14 I/O...14...16 BIOS...22 (For Example BIOS Verson:F3b)... 23 CMOS... 25 BIOS... 28... 31 2
... 34... 41 P CI... 45... 47 /... 49 Fail-Safe... 50 Optimized... 51 (Supervisor)/ (User)... 52 SETUP... 53 SETUP... 54...55... 55... 56 Easy TuneIII TM... 57 @ BIOS TM... 58...59 3
GA-8IRM 2.2 GA-8IRM Feb.2001 The GA-8IRM x 1 / x 1 (IUCD) GA-8IRM I/O x 1 4
1. 2. 3. (CPU RAM) 4. 5. ATX PCB 5
GA-8IRM Flex ATX 19.0 x 22.9 GA-8IRM GA-8IRM GA-8IRML Socket478 Intel Micro FC-PGA2 Pentium 4 I/O IDE Intel Pentium 4 (Northwood, 0.13um) Intel Pentium 4 400MHz FSB 2nd CPU Chipset 82845 HOST/AGP/Controller 82801BA(ICH2)I/O Controller Hub 2 184-pin DIMM PC160/PC2100 DDR DIMM 2.5V DDR DIMM 64bit ECC type DRAM integrity mode GB W83627HF 1 AGP 4X (1.5V) 3 PCI 33MHz PCI2.2 compliant 2 IDE bus master (UDMA 33/ATA 66/ATA 100) IDE 4 ATAPI PIO mode 3,4,5,UDMA33/ATA66/ATA100 IDE ATAPI CD- ROM 1 (360K,720K,1.2M,1.44M 2.88M bytes) 1 Normal/EPP/ECP 2 (COM A & COM B) 4 USB ( x 2, x 2) 1 CPU CPU CPU 6...
AC97 CODEC(RealTek ALC201A) PS/2 Line In/Line Out/Mic In/CD In/Game Port PS/2 PS/2 Intel 82562ET * BIOS AWARD BIOS,2M bit PS/2 PS/2 AC Recovery USB wake up from S3 @BIOS Easy Tune III CPU CPU,,,, ;CPU,,,. * GA-8IRML. 7
GA-8IRM GA-8IRM Layout KB_MS CPU_FAN COMA PWR_FAN ATX FDD LPT AUX_12V COMB SOCKET478 GA-8IRM(L) MIC_IN LINE_OUT LINE_IN USB/ GAME LAN* 82562ET* CD_IN F_AUDIO LAN_EN* AC97 CI W83627HF AGP Brookdale WOL PCI1 ICH2 PCI2 FWH PCI3 DDR1 DDR2 IDE2 IDE1 SYS _FAN BATTERY F_USB IR F_PANEL * GA-8IRML. 8
1 - (CPU) 2-3 - 4-5 - BIOS 6 - Step4 Step1 Step 2 Step 4 Step 4 Step3 9
GA-8IRM 1: (CPU) 1 1 1 1. 2. ( 90. 3.,. ). C P U,,,. 1 0
1. CPU 2. CPU CPU, ;.. I n t e l C P U ( C P U C P U, C P U, ), C P U C P U F A N, ( ) 1 1
GA-8IRM 2 : 2 184Pin(DIMM),BIOS. DIMM,,, :NEC, Toshiba, PQI, Winbond. Unbuffered DDR DIMM Devices used on DIMM 1 DIMM x 64 / x 72 2 DIMMs x 64 / x 72 64 Mbit (2Mx8x4 banks) 128 MBytes 256 MBytes 64 Mbit (1Mx16x4 banks) 32 MBytes 64 MBytes 128 Mbit(4Mx8x4 banks) 256 MBytes 512 MBytes 128 Mbit(2Mx16x4 banks) 64 MBytes 128 MBytes 256 Mbit(8Mx8x4 banks) 512 MBytes 1 GBytes 256 Mbit(4Mx16x4 banks) 128 MBytes 256 MBytes 512 Mbit(16Mx8x4 banks) 1 GBytes 2 GBytes 512 Mbit(8Mx16x4 banks) 256 MBytes 512 MBytes : Intel 845 x16 DDR. DDR 1.,. 2.,,.,. 3. DIMM.,,, STR/DIMM, DIMM. 1 2
DDR DDR(Double Data Rate) PC SDRAM SDRAM DDR OEM DDR SDRAM SDRAM DDR SDRAM DDR 2.1GB/s DDR DRAM PC SDRAM 3.3 volts DDR 2.5 volts DDR 3 : 1. 2. ( ) 3. 4. 5. 6. 7. BIOS 8. AGP / AGP,. AGP AGP. AGP 1 3
GA-8IRM 4 : I/O ❶ ❷ ❺ ❹ ❶ PS/2 PS/2 PS/2 PS/2 PS/2 (6 pin Female) PS/2 (6 pin Female) ❷ A / B / (25 pin Female) A (9 pin Male) B 1 4
(15 pin Female) ❹ Line Out MIC In Line In ❺, LAN* Connector USB 0 USB 1 USB USB USB USB ZIP USB. USB * GA-8IRML. 1 5
GA-8IRM A B C D E P O N M F G H I J L K A) AUX_12V B) CPU_FAN C) PWR_FAN D) ATX E) FDD F) IDE1/IDE2 G) BATTERY H) SYS_FAN I) IR J) F_PANEL K) FP_USB L) WOL M) LAN_EN* N) CD_IN O) CI P) F_AUDIO * GA-8IRML. 1 6
A) AUX_12 ( +12V ) +12V +12V 4 3 2 1 AGPPRO ( +12V 12 ) B) CPU_FAN ( C P U ) +12V/Control CPU 600 1 C) PWR_FAN H) SYS_FAN ( ) ( ) 1 +12V/Control 1 +12V/Control O) CI ( ). GND 1 Signal 1 7
GA-8IRM IDE E) FDD ( ) 1 F) IDE1/ IDE2 ( I D E ) IDE ID E IDE 1 1 IDE1 IDE2 K) F_USB ( ) USB USB D3+ USB D3- USB USB 1 USB D2- USB D2+ 1 8
N) CD_IN1 ( ) 1 CD-R CD-L I) IR 1 IR Data Output IR Data Input VCC(+5V) P) F_AUDIO( ) Rear Audio (L) Rear Audio (R) Incase speaker (L) 1 Front Audio (L) Front Audio (R) +12V MIC GND Incase speaker (R) : Pin11-12 Pin13-14 Jumper 1 9
GA-8IRM L) WOR ( ) 1 +5V SB M) LEN_EN( )* 1 1 1-2 : ( ) 2-3 : JUMP JUMPER D) ATX (ATX ) AC (110/ 20 +12V 5V SB (Stand by +5V) VCC VCC 3.3V 3.3V 1 220V) ATX VCC ATX VCC AC (110/ -5V 220V) PS-ON(Soft On/Off) -12V 3.3V * GA-8IRML. 2 0
J) F_PANEL (2x7 Pins ) 2 14 RST- RST+ SPK+ 1 SPK- HD- 1 13 HD (IDE Hard Disk Active LED) SPK (Speaker Connector) RST (Reset Switch)) PD+/PD_G/PD_Y(Power LED) PW (Soft Power Connector) 1 PD+ PD_G- PD_Y- PW+ PW- HD+ Pin 1: LED anode(+) Pin 2: LED cathode(-) Pin 1: VCC(+) +5v Pin 2- Pin 3: NC Pin 4: Data(-) Open: Normal Operation Close: Reset Hardware System Pin 1: LED anode(+) Pin 2: LED cathode(-) Pin 3: LED cathode(-) Open: Normal Operation : Close: Power On/Off : / G) BAT( ) + 2 1
GA-8IRM Series Motherboard Chapter 3 BIOS Setup BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. ENTERING SETUP Power ON the computer and press <Del> immediately will allow you to enter Setup. CONTROL KEYS < > < > < > < > <Esc> <+/PgUp> <-/PgDn> <F1> <F2> <F3> <F4> <F5> <F6> <F7> <F8> <F9> <F10> Move to previous item Move to next item Move to the item in the left hand Move to the item in the right hand Main Menu - Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu - Exit current page and return to Main Menu Increase the numeric value or make changes Decrease the numeric value or make changes General help, only for Status Page Setup Menu and Option Page Setup Menu Reserved Reserved Reserved Restore the previous CMOS value from CMOS, only for Option Page Setup Menu Load the default CMOS value from BIOS default table, only for Option Page Setup Menu Load the Setup Defaults Reserved Reserved Save all the CMOS changes, only for Main Menu 22
BIOS Setup GETTING HELP Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu / Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press <Esc>. Q-Flash Utility After power on the computer, pressing <Del> immediately during POST (Power On Self Test) it will allow you to enter Award BIOS CMOS SETUP, then press <F8> to enter Q-Flash utility. The Main Menu (For example: BIOS Ver. :F3b) Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 1) will appear on the screen. The Main Menu allows you to select from eight setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. CMOS Setup Utility-Copyright (C) 1984-2001 Award Software Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status ESC:Quit Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving :Select Item F8: Q-Flash F10:Save & Exit Setup Time, Date, Hard Disk Type... Figure 1: Main Menu Standard CMOS Features This setup page includes all the items in standard compatible BIOS. 23
GA-8IRM Series Motherboard Advanced BIOS Features This setup page includes all the items of Award special enhanced features. Advanced Chipset Features This setup page includes all the items of chipset special features. Integrated Peripherals This setup page includes all onboard peripherals. Power Management Setup This setup page includes all the items of Green function features. PnP/PCI Configurations This setup page includes all the configurations of PCI & PnP ISA resources. PC Health Status This setup page is the System auto detect Temperature, voltage, fan, speed. Frequency/Voltage Control This setup page is control CPU s clock and frequency ratio. Load Fail-Safe Defaults Fail-Safe Defaults indicates the value of the system parameters which the system would be in safe configuration. Load Optimized Defaults Optimized Defaults indicates the value of the system parameters which the system would be in best performance configuration. Set Supervisor password Change, set, or disable password. It allows you to limit access to the system and Setup, or just to Setup. Set User password Change, set, or disable password. It allows you to limit access to the system. Save & Exit Setup Save CMOS value settings to CMOS and exit setup. Exit Without Saving Abandon all CMOS value changes and exit setup. 24
BIOS Setup Standard CMOS Features CMOS Setup Utility-Copyright (C) 1984-2001 Award Software Standard CMOS Features Date (mm:dd:yy) Sun, Jan 7 2001 Item Help Time (hh:mm:ss) 22:31:24 Menu Level IDE Primary Master Press Enter None IDE Primary Slave Press Enter None IDE Secondary Master Press Enter None IDE Secondary Slave Press Enter None Drive A [1.44M, 3.5 ] Drive B [None] Floppy 3 Mode Support [Disabled] Halt On [All, But Keyboard] Base Memory 640K Extended Memory 130048K Total Memory 131072K : Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 2: Standard CMOS Features Date The date format is <week>, <month>, <day>, <year>. Week The week, from Sun to Sat, determined by the BIOS and is display only Month The month, Jan. Through Dec. Day The day, from 1 to 31 (or the maximum allowed in the month) Year The year, from 1994 through 2079 Time The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour militarytime clock. For example, 1 p.m. is 13:00:00. 25
GA-8IRM Series Motherboard IDE Primary Master, Slave / Secondary Master, Slave The category identifies the types of hard disk from drive C to F that has been installed in the computer. There are two types: auto type, and manual type. Manual type is user-definable; Auto type which will automatically detect HDD type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If you select User Type, related information will be asked to enter to the following items. Enter the information directly from the keyboard and press <Enter>. Such information should be provided in the documentation form your hard disk vendor or the system manufacturer. CYLS. Number of cylinders HEADS number of heads PRECOMP write precomp LANDZONE Landing zone SECTORS number of sectors If a hard disk has not been installed select NONE and press <Enter>. Drive A / Drive B The category identifies the types of floppy disk drive A or drive B that has been installed in the computer. None No floppy drive installed 360K, 5.25 in. 5.25 inch PC-type standard drive; 360K byte capacity. 1.2M, 5.25 in. 5.25 inch AT-type high-density drive; 1.2M byte capacity (3.5 inch when 3 Mode is Enabled). 720K, 3.5 in. 3.5 inch double-sided drive; 720K byte capacity 1.44M, 3.5 in. 3.5 inch double-sided drive; 1.44M byte capacity. 2.88M, 3.5 in. 3.5 inch double-sided drive; 2.88M byte capacity. Floppy 3 Mode Support (for Japan Area) Disabled Drive A Drive B Both Normal Floppy Drive. (Default value) Drive A is 3 mode Floppy Drive. Drive B is 3 mode Floppy Drive. Drive A & B are 3 mode Floppy Drives. 26
BIOS Setup Halt on The category determines whether the computer will stop if an error is detected during power up. NO Errors All Errors All, But Keyboar The system boot will not stop for any error that may be detected and you will be prompted. Whenever the BIOS detects a non-fatal error the system will be stopped. The system boot will not stop for a keyboard error; it will stop for all other errors. (Default value) All, But Diskette The system boot will not stop for a disk error; it will stop for all other errors. All, But Disk/Key The system boot will not stop for a keyboard or disk error; it will stop for all other errors. Memory The category is display-only which is determined by POST (Power On Self Test) of the BIOS. Base Memory The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system. The value of the base memory is typically 512 K for systems with 512 K memory installed on the motherboard, or 640 K for systems with 640 K or more memory installed on the motherboard. Extended Memory The BIOS determines how much extended memory is present during the POST. This is the amount of memory located above 1 MB in the CPU s memory address map. 27
GA-8IRM Series Motherboard Advanced BIOS Features CMOS Setup Utility-Copyright (C) 1984-2001 Award Software Advanced BIOS Features BIOS Flash Protection [Auto] First Boot Device [Floppy] Item Help Second Boot Device [HDD-0] Menu Level Third Boot Device [CDROM] Boot Up Floppy Seek [Disabled] Boot Up Num-Lock [On] Password Check [Setup] Interrupt Mode [APIC] MPS Version Control For OS [1.4] HDD S.M.A.R.T. Capability [Disabled] : Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 3: Advanced BIOS Features BIOS Flash Protection This field lets you determine the states that flash BIOS Enabled Auto During POST, DMI/ESCD would not be updated. But flash tools can update BIOS always BIOS enables flash write access automatically when updating BIOS data/ DMI/ESCD. (Default Value) First / Second / Third Boot device Floppy Select your boot device priority by Floppy. LS120 Select your boot device priority by LS120. 28
BIOS Setup HDD-0~3 SCSI CDROM LAN USB-CDROM USB-ZIP USB-FDD USB-HDD ZIP Disabled Select your boot device priority by HDD-0~3. Select your boot device priority by SCSI. Select your boot device priority by CDROM. Select your boot device priority by LAN. Select your boot device priority by USB-CDROM. Select your boot device priority by USB-ZIP. Select your boot device priority by USB-FDD. Select your boot device priority by USB-HDD. Select your boot device priority by ZIP. Disabled this function. Boot Up Floppy Seek During POST, BIOS will determine the floppy disk drive installed is 40 or 80 tracks. 360 K type is 40 tracks 720 K, 1.2 M and 1.44 M are all 80 tracks. Enabled BIOS searches for floppy disk drive to determine it is 40 or 80 tracks. Note that BIOS can not tell from 720 K, 1.2 M or 1.44 M drive type as they are all 80tracks. Disabled BIOS will not search for the type of floppy disk drive by track number. Note that there will not be any warning message if the drive installed is 360 K. (Default value) Boot Up NumLock On Off Keypad is number keys. (Default value) Keypad is arrow keys. Password Check This category allows you to limit access to the system and Setup, or just to Setup. System Setup The user must enter correct password in order to access the system and/or BIOS setup. The user must enter correct password in order to access BIOS setup utility. (Default value) 29
GA-8IRM Series Motherboard Interrupt Mode APIC Through IOAPIC generate more IRQ for system use.(default value) PIC Use AT stantard IRQ controlles to generate IRQ. When you already have IOAPIC enable system and want to upgrade the system please note, since running an IOAPIC enabled OS (like Windows NT,Windows 2000, Windows XP...) system with none IOAPIC HW support will cause the system to hang. Following are some situations users might run into: 1.An IOAPIC enabled OS and change the BIOS setting from IOAPIC to PIC, this will cause your system to hang. MPS Version Control For OS (Support Multi Processor Specification revision 1.4) Note: Some old MPS OS support 1.1 version only 1.4 Support MPS Version 1.4. (Default Value) 1.1 Support MPS Version 1.1. HDD S.M.A.R.T. Capability Enabled Disabled Enabled HDD S.M.A.R.T. Capability. Disabled HDD S.M.A.R.T. Capability. (Default value) 30
BIOS Setup Advanced Chipset Features CMOS Setup Utility-Copyright (C) 1984-2001 Award Software Advanced Chipset Features Configure DRAM Timing [SPD] Item Help CAS Latency Time 2.5 Menu Level Active to Precharge Delay 7 DRAM RAS# to CAS# Delay 3 DRAM RAS# Precharge 3 Refresh Mode Select 15.6usec DRAM Data IntegtityMode Non-ECC DRAM Read Thermal Mgmt [Disable] Delay Transaction [Enable] AGP Aperture Size(MB) [64] Delay Prior to Thermal [16Min] : Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 4: Advanced Chipset Features Configure DRAM Timing Warning: Wrong DRAM Timing may make system can t boot.clear CMOS to overcome wrong Timing issue) SPD Manual Set Configure DRAM Timing Control by SPD. (Default value) Set Configure DRAM Timing Control by Manual. CAS latency Time 2.5 Set CAS latency Time is 2.5. (Default Value) 2 Set CAS latency Time is 2. 1.5 Set CAS latency Time is 1.5. Active to Precharge Delay 5 6 Set active to Precharge delay timing is 5 clk. Set active to Precharge delay timing is 6 clk. 31
GA-8IRM Series Motherboard 7 Set active to Precharge delay timing is 7 clk.(default value) DRAM RAS# to CAS# delay 3 2 Set DDR RAM RAS# to CAS# delay 3 SCLKs. (Default value) Set DDR RAM RAS# to CAS# delay 2 SCLKs. DRAM RAS# Precharge 3 Set DDR RAM RAS# Precharge Time to 3. (Default value) 2 Set DDR RAM RAS# Precharge Time to 2. Refresh Mode Select 7.8 usec Set active to Refresh mode timing is 7.8 usec. 15.6 usec Set active to Refresh mode timing is 15.6 usec.(default) 64 usec Set active to Refresh mode timing is 64 usec. DRAM Data Integrity Mode ECC ³] wdram Data Integrity Mode by ECC. Non-ECC ³] wdram Data Integrity Mode by Non-ECC. (¹w³] È) DRAM Data Integrity Mode ECC Non-ECC Set DRAM Data Integrity Mode by ECC. Set DRAM Data Integrity Mode by Non-ECC. (Default value) DRAM Read Thermal Mgmt Disabled Disabled this function.(default) Enabled Enabled can reduce DRAM heat issue. Note:DRAM heat thermal mangement is always enabled in write cycle. 32
BIOS Setup Delay Transaction Disabled Enabled Normal operation. For slow speed ISA device in system. (Default value) AGP Graphics Aperture Size (Driver use selected size of system memory for 3D texturing to increase video performance) 4 8 16 32 64 128 AGP Graphics Aperture Size is 4MB. AGP Graphics Aperture Size is 8MB. AGP Graphics Aperture Size is 16MB AGP Graphics Aperture Size is 32MB. AGP Graphics Aperture Size is 64MB.(Default Value) AGP Graphics Aperture Size is 128MB. 256 Delay Prior to Thermal AGP Graphics Aperture Size is 256MB. 4Min 8Min 16Min 32Min Set active CPU Thermal function after booting 4 Min. Set active CPU Thermal function after booting 8 Min. Set active CPU Thermal function after booting 16 Min. (Default Value) Set active CPU Thermal function after booting 32 Min. 33
GA-8IRM Series Motherboard Integrated Peripherals CMOS Setup Utility-Copyright (C) 1984-2001 Award Software Integrated Peripherals On-Chip Primary PCI IDE [Enabled] Item Help On-Chip Secondary PCI IDE [Enabled] IDE Primary Master PIO [Auto] Menu Level IDE Primary Slave PIO [Auto] IDE Secondary Master PIO [Auto] IDE Secondary Slave PIO [Auto] IDE Primary Master UDMA [Auto] IDE Primary Slave UDMA [Auto] IDE Secondary Master UDMA [Auto] IDE Secondary Slave UDMA [Auto] IDE1 Conductor Cable [Auto] IDE2 Conductor Cable [Auto] USB Controller [Enabled] USB Keyboard Support [Disabled] USB Mouse Support [Disabled] Init Display First [AGP] AC97 Audio [Auto] Mouse Power On [Disabled] Keyboard Power On [Disabled] KB Power ON Password Enter Onboard FDC Controller [Enabled] Onboard Serial Port 1 [3F8/IRQ4] Onboard Serial Port 2 [2F8/IRQ3] UART Mode Select [Normal] RxD,TxD Active Hi,Lo IR Transmission Delay Enabled UR2 Duplex Mode Half Use IR Pins IR-Rx2Tx2 34
BIOS Setup Onboard Parallel Port Parallel Port Mode EPP Mode Select ECP Mode Use DMA 3 AC BACK Function [378/IRQ7] [SPP] EPP1.7 [Soft-Off] Game Port Address [201] Mdi Port Address [330] Midi Port IRQ [10] : Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 5: Integrated Peripherals On-Chip Primary PCI IDE Enabled Disabled Enable onboard 1st channel IDE port. (Default value) Disable onboard 1st channel IDE port. On-Chip Secondary PCI IDE Enabled Disabled Enable onboard 2nd channel IDE port. (Default value) Disable onboard 2nd channel IDE port. IDE Primary Master PIO (for onboard IDE 1st channel) Auto Mode0~4 BIOS will automatically detect the IDE HDD Accessing mode. (Default value) Manually set the IDE Accessing mode. IDE Primary Slave PIO (for onboard IDE 1st channel) Auto Mode0~4 BIOS will automatically detect the IDE HDD Accessing mode. (Default value) Manually set the IDE Accessing mode. 35
GA-8IRM Series Motherboard IDE Secondary Master PIO (for onboard IDE 2nd channel) Auto BIOS will automatically detect the IDE HDD Accessing mode. (Default value) Mode0~4 Manually set the IDE Accessing mode. IDE Secondary Slave PIO (for onboard IDE 2nd channel) Auto BIOS will automatically detect the IDE HDD Accessing mode. (Default value) Mode0~4 Manually set the IDE Accessing mode. IDE Primary Master UDMA Auto BIOS will automatically detect the IDE HDD Accessing mode. (Default value) Disabled Disable UDMA function. IDE Primary Slave UDMA Auto BIOS will automatically detect the IDE HDD Accessing mode. (Default value) Disabled Disable UDMA function. IDE Secondary Master UDMA Auto Disabled BIOS will automatically detect the IDE HDD Accessing mode. (Default value) Disable UDMA function. IDE Secondary Slave UDMA Auto Disabled BIOS will automatically detect the IDE HDD Accessing mode. (Default value) Disable UDMA function. 36.
BIOS Setup IDE1 Conductor Cable Auto ATA66/100 ATA33 Will be automatically detected by BIOS (Default Value) Set IDE1 Conductor Cable to ATA66/100 (Please make sure your IDE device and cable is compatible with ATA66/100) Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE device and cable is compatible with ATA33) IDE2 Conductor Cable Auto ATA66/100 ATA33 Will be automatically detected by BIOS (Default Value) Set IDE2 Conductor Cable to ATA66/100 (Please make sure your IDE device and cable is compatible with ATA66/100) Set IDE2 Conductor Cable to ATA33 (Please make sure your IDE device and cable is compatible with ATA33). USB Controller Enabled Disabled Enabled USB Controller. (Default value) Disabled USB Controller. USB Keyboard Support Enabled Disabled Enabled USB Keyboard Support. Disabled USB Keyboard Support. (Default value) USB Mouse Support Enabled Disabled Enabled USB Mouse Support. Disabled USB Mouse Support. (Default value) Init Display First PCI AGP Set Init Display First to PCI Slot. Set Init Display First to AGP. (Default value) 37
GA-8IRM Series Motherboard AC97 Audio Auto BIOS will automatically detect onboard AC97 Audio or Creative CT5880 audio. (Default value) Disabled Disabled AC97 Audio. Mouse Power On Disabled Double Right Double Left Disabled this function. (Default value) Set mouse power on by double click mouse right bottom. Set mouse power on by double click mouse left bottom. Keyboard Power On Password Disabled Keyboard 98 Any Key Enter from 1 to 5 characters to set the Keyboard Power On Password. Disabled this function. (Default value) If your keyboard have POWER Key button, you can press the key to power on your system. Set Keyboard power on by any key KB Power ON Password Enter Input password (from 1 to 5 characters) and press Enter to set the Key board Power On Password.. Onboard FDC Controller Enabled Disabled Enable onboard FDC port. (Default value) Disable onboard FDC port. Onboard Serial Port 1 Auto BIOS will automatically setup the port 1 address. 3F8/IRQ4 Enable onboard Serial port 1 and address is 3F8. (Default value) 2F8/IRQ3 Enable onboard Serial port 1 and address is 2F8. 3E8/IRQ4 Enable onboard Serial port 1 and address is 3E8. 2E8/IRQ3 Enable onboard Serial port 1 and address is 2E8. 38
BIOS Setup Disabled Disable onboard Serial port 1. Onboard Serial Port 2 Auto BIOS will automatically setup the port 2 address. 3F8/IRQ4 Enable onboard Serial port 2 and address is 3F8. 2F8/IRQ3 Enable onboard Serial port 2 and address is 2F8. (Default Value) 3E8/IRQ4 Enable onboard Serial port 2 and address is 3E8. 2E8/IRQ3 Enable onboard Serial port 2 and address is 2E8. Disabled Disable onboard Serial port 2. UART Mode Select (This item allows you to determine which Infra Red(IR) function of Onboard I/O chip) ASKIR IrDA Normal Set onboard I/O chip UART to ASKIR Mode. Set onboard I/O chip UART to IrDA Mode. Set onboard I/O chip UART to Normal Mode. (Default Value) RxD, TxD Active Hi, Hi Set RxD,TxD Active to Hi, Hi. Hi, Lo Set RxD,TxD Active to Hi, Lo. (Default Value) Lo, Hi Set RxD,TxD Active to Lo, Hi. Lo, Lo Set RxD,TxD Active to Lo, Lo. IR Transmission Delay Enabled Disabled Enabled IR Transmission delay. (Default Value) Enabled IR Transmission delay. UR2 Duplex Mode Half Full IR Function Duplex Half. (Default Value) IR Function Duplex Full. 39
GA-8IRM Series Motherboard Use IR Pins IR-Rx2xTx2 RxD2,TxD2 Set IR Pins use IR-Rx2xTx2. (Default Value) Set IR Pins use RxD2,TxD2. OnBoard Parallel port 378/IRQ7 Enable On Board LPT port and address is 378.(Default Value) 278/IRQ5 Enable On Board LPT port and address is 278. 3BC/IRQ7 Enable On Board LPT port and address is 3BC. Parallel Port Mode SPP EPP ECP ECP+EPP Using Parallel port as Standard Parallel Port. (Default Value) Using Parallel port as Enhanced Parallel Port. Using Parallel port as Extended Capabilities Port. Using Parallel port as ECP & EPP mode. EPP Mode Select EPP 1.9 EPP Version is 1.9. EPP 1.7 EPP Version is 1.7.(Default value) ECP Mode Use DMA 3 Set ECP mode use DMA 3. (Default value) 1 Set ECP mode use DMA 1. AC Back Function Memory Soft-Off Full-On System power on depends on the status before AC lost. Always in Off state when AC back. (Default value) Always power on the system when AC back. 40
BIOS Setup Game Port Address Disabled Disabled this function. 201 Set Game Port Address to 201. (Default Value) 209 Set Game Port Address to 209. Midi Port Address Disabled Disabled this function. 290 Set Midi Port Address to 290. 300 Set Midi Port Address to 300. 330 Set Midi Port Address to 300.(Default Value) Midi Port IRQ 5 10 Set 5 for Midi Port IRQ. Set 11 for Midi Port IRQ. (Default Value) 41
GA-8IRM Series Motherboard Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2001 Award Software Power Management Setup ACPI Suspend Type [S1(POS)] Item Help USB Device Wake-Up From S3 Disabled Power Management [User Define] Menu Level Video Off Method [DPMS] Video Off In Suspend [Yes] Suspend Type [Stop Grant] MODEM Use IRQ [3] Suspend Mode [Disabled] HDD Power Down [Disabled] Soft-Off by PWR-BTTN [Instant-off] PME Event Wake Up [Enabled] ModemRingOn/WakeOnLan [Enabled] Resume by Alarm [Disabled] Date(of Month) Alarm Everyday Time(hh:mm:ss) Alarm 0 0 0 ** Reload Global Timer Events ** Primary IDE 0 Primary IDE 1 Secondary IDE 0 Secondary IDE 1 FDD,COM,LPT Port PCI PIRQ[A-H]# [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] : Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 6: Power Management Setup 42
BIOS Setup ACPI Suspend Type S1/POS S3/STR Set ACPI Suspend Type to S1/POS (Power On Suspend). (Default value) Set ACPI Suspend Type to S3/STR (Suspend To RAM). USB Device Wakeup From S3 Enabled Enable USB Device Wakeup From S3. Disabled Disable USB Device Wakeup From S3. (Default value) Power Management User Define Min Saving Max Saving For configuring our own power management features (Default Value) Disabled Green & software APM function. Enabled Green & software APM function. Video off Method V/H SYNC+Blank Blank Screen DPMS BIOS will turn off V/H-SYNC when gets into Green mode for Green monitor power saving. BIOS will only black monitor when gets into Green mode. BIOS will use DPMS Standard to control VGA card. (The Green type VGA card will turn off V/H-SYNC automatically.)(default value) Video Off In Suspend Yes No Set Suspend type is stop grant. (Default value) Set Suspend type is Power on Suspend. Suspend Type Stop Grant PwrOn Suspend Set Suspend type is stop grant. (Default value) Set Suspend type is Power on Suspend. 43
GA-8IRM Series Motherboard MODEM Use IRQ N/A Set MODEM Use IRQ to NA. 3 Set MODEM Use IRQ to 3.(Default value) 4 Set MODEM Use IRQ to 4. 5 Set MODEM Use IRQ to 5. 7 Set MODEM Use IRQ to 7. 9 Set MODEM Use IRQ to 9. 10 Set MODEM Use IRQ to 10. 11 Set MODEM Use IRQ to 11. Suspend Mode Disabled 1 min - 1 Hour Disabled Suspend Mode. (Default value) Setup the timer to enter Suspend Mode. HDD Power Down Disabled Disabled HDD Power Down mode function. (Default value) 1-15 mins. Enabled HDD Power Down mode between 1 to 15 mins. Soft-off by PWR-BTTN Instant-off Delay 4 Sec. Press power button then Power off instantly. (Default value) Press power button 4 sec to Power off. Enter suspend if button is pressed less than 4 sec. PME Event Wake up Disabled Enabled Disabled PME Event Wake up function. Enabled PME Event Wake up function. (Default Value) 44
BIOS Setup Modem Ring On/ WakeOnLAN Disabled Enabled Disabled Modem Ring On / Wake On LAN function. Enabled Modem Ring On / Wake On LAN function. (Default Value) Resume by Alarm You can set "Resume by Alarm" item to enabled and key in Data/time to power on system. Disabled Disable this function. (Default Value) Enabled Enable alarm function to POWER ON system. If RTC Alarm Lead To Power On is Enabled. Date ( of Month) Alarm : Everyday, 1~31 Time ( hh: mm: ss) Alarm : (0~23) : (0~59) : (0~59) Primary IDE 0/1 Disabled Enabled Disabled this function. (Default value) Enabled monitor Primary IDE 0/1 for Green event. Secondary IDE 0/1 Disabled Enabled Disabled this function. (Default value) Enabled monitor Secondary IDE 0/1 for Green event. FDD,COM,LPT Port Disabled Enabled Disabled this function. (Default value) Enabled monitor FDC,COM,LPT for Green event. PCI PIRQ[A-H] # Enabled Disabled Monitor PCI PIRQ[A-H]# IRQ Active. Ignore PCI PIRQ[A-H]# IRQ Active. (Default value) 45
GA-8IRM Series Motherboard PnP/PCI Configurations CMOS Setup Utility-Copyright (C) 1984-2001 Award Software PnP/PCI Configurations Resources Controlled By [Auto ] Item Help IRQ Resources Press Enter Menu Level PCI1 IRQ Assignment [Auto] PCI2 IRQ Assignment [Auto] PCI3 IRQ Assignment [Auto] : Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 7: PnP/PCI Configurations Resources Controlled by Manual Auto(ESCD) User can set the PnP resource (I/O Address, IRQ & DMA channels) used by legacy ISA DEVICE. BIOS automatically use these PnP rescuers. (Default value) IRQ Resources ( 3,4,5,7,9,10,11,12,15 ) PCI Device Reserved The resource is used by PCI device. Set the resource to reserved. PCI1 IRQ Assignment Auto 3,4,5,7,9.,10,11,12,15 Auto assign IRQ to PCI 1. (Default value) Set 3,4,5,7,9,10,11,12,15 to PCI1/ PCI5. PCI2 IRQ Assignment Auto 3,4,5,7,9.,10,11,12,15 Auto assign IRQ to PCI 2. (Default value) Set 3,4,5,7,9,10,11,12,15 to PCI2/ PCI6. 46
BIOS Setup PCI3 IRQ Assignment Auto 3,4,5,7,9.,10,11,12,15 Auto assign IRQ to PCI 3. (Default value) Set 3,4,5,7,9,10,11,12,15 to PCI3. 47
GA-8IRM Series Motherboard PC Health Status CMOS Setup Utility-Copyright (C) 1984-2001 Award Software PC Health Status Reset Case Open Status [Disabled] Case Opened No VCORE 1.746V Item Help +3.3V 3.296V Menu Level + 5V 5.080 V +12V 11.904V Current System Temperature 34 C/93 F Current CPU Temperature 45 C/113 F Current CPU FAN Speed 4821 RPM Current POWER FAN Speed 0 RPM Current SYSTEM FAN speed 0 RPM CPU Warning Temperature [Disabled] CPU FAN Fail Warning [Disabled] POWER FAN Fail Warning [Disabled] SYSTEM FAN Fail Warning [Disabled] : Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure8: PC Health Status Reset Case Open Status Case Opened If the case is closed, "Case Opened" will show "No". If the case have been opened, "Case Opened" will show "Yes". If you want to reset "Case Opened" value, set "Reset Case Open Status" to "Enabled" and save CMOS, your computer will restart. Current Voltage (V) VCORE / +3.V / +5V / +12V Detect system s voltage status automatically. 48
BIOS Setup Current CPU / SYSTEM Temperature ( C) Detect CPU /SYSTEM Temp. automatically. Current CPU FAN / POWER FAN/ SYSTEM FAN Speed (RPM) Detect Fan speed status automatically. CPU Warning Temperature 60 C / 140 F 70 C / 158 F 80 C / 176 F 90 C / 194 F Disabled Monitor CPU Temp. at 60 C / 140 F. Monitor CPU Temp. at 70 C / 158 F. Monitor CPU Temp. at 80 C / 176 F. Monitor CPU Temp. at 90 C / 194 F. Disabled this function.(default value) Fan Fail Warning ( CPU / POWER / SYSTEM) Disabled Enabled Fan Fail Alarm Function Disabled. (Default value) Fan Fail Alarm Function Enabled. 49
GA-8IRM Series Motherboard Frequency/Voltage Control CMOS Setup Utility-Copyright (C) 1984-2001 Award Software Frequency/Voltage Control CPU Clock Ratio [x 15] Item Help CPU Host Clock Control [Disable] Menu Level CPU Host Frequency(MHz) 100 Host/DRAM Clock ratio [Auto] Memory Frequency(MHz) 266 PCI/AGP Frequency(MHz) 33/66 : Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 9: Frequency/Voltage Control CPU Clock Ratio Set CPU Ratio if CPU Ratio is unlocked. X8~X 24 It s depends on CPU Clock Ratio. CPU Host Clock Control Note: If system hangs up before enter CMOS setup utility, wait for 10 sec for times out reboot. When time out occur, system will reset and run at CPU default Host clock at next boot. Disable Disable CPU Host Clock Control.(Default value) Enable Enable CPU Host Clock Control. CPU Host Frequency 100MHz ~ 200MHzSet CPU Host Clock from 100MHz to 200MHz. 50
BIOS Setup Host/DRAM Clock Ratio (Warning: wrong frequency may make system can t boot, clear CMOS to overcome wrong frequency issue) 2.0 Memory Frequency = Host clock X 2.0. 2.66 Memory Frequency = Host clock X 2.66. Auto Set Memory frequency by DRAM SPD data. (Default value) PCI/AGP Frequency(Mhz) The values depend on CPU Host Frequency(Mhz). Memory Frequency(Mhz) The values depend on CPU Host Frequency(Mhz). 51
GA-8IRM Series Motherboard Load Fail-Safe Defaults CMOS Setup Utility-Copyright (C) 1984-2001 Award Software Standard CMOS Features Frequency/Voltage Control Advanced BIOS Features Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP/PCI Configurations Save & Exit Setup Load Fail-Safe Defaults? (Y/N)?Y PC Health Status Exit Without Saving ESC:Quit :Select Item F8: Q-Flash F10:Save & Exit Setup Load Fail-Safe Defaults Figure 11: Load Fail-Safe Defaults Load Fail-Safe Defaults Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system performance. 52
BIOS Setup Load Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2001 Award Software Standard CMOS Features Frequency/Voltage Control Advanced BIOS Features Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP/PCI Configurations PC Health Status ESC:Quit Save & Exit Setup Load Optimized Defaults? (Y/N)?Y Exit Without Saving :Select Item F8: Q-Flash F10:Save & Exit Setup Load Optimized Defaults Figure 12: Load Optimized Defaults Load Optimized Defaults Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects. 53
GA-8IRM Series Motherboard Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2001 Award Software Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status ESC:Quit Enter Password: Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving :Select Item F8: Q-Flash F10:Save & Exit Setup Change/Set/Disable Password Figure 13: Password Setting When you select this function, the following message will appear at the center of the screen to assist you in creating a password. Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter a password. To disable password, just press <Enter> when you are prompted to enter password. A message PASSWORD DISABLED will appear to confirm the password being disabled. Once the password is disabled, the system will boot and you can enter Setup freely. The BIOS Setup program allows you to specify two separate passwords: a SUPERVISOR PASS- WORD and a USER PASSWORD. When disabled, anyone may access all BIOS Setup program function. When enabled, the Supervisor password is required for entering the BIOS Setup program and having full configuration fields, the User password is required to access only basic items. If you select System at Security Option in Advance BIOS Features Menu, you will be prompted for the password every time the system is rebooted or any time you try to enter Setup Menu. If you select Setup at Security Option in Advance BIOS Features Menu, you will be prompted only when you try to enter Setup. 54
BIOS Setup Save & Exit Setup CMOS Setup Utility-Copyright (C) 1984-2001 Award Software Standard CMOS Features Frequency/Voltage Control Advanced BIOS Features Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP/PCI Configurations Save & Exit Setup PC Health Status ESC:Quit Exit Without Saving Save to CMOS and EXIT (Y/N)? Y :Select Item F8: Q-Flash F10:Save & Exit Setup Save Data to CMOS Figure 14: Save & Exit Setup Type Y will quit the Setup Utility and save the user setup value to RTC CMOS. Type N will return to Setup Utility. 55
GA-8IRM Series Motherboard Exit Without Saving CMOS Setup Utility-Copyright (C) 1984-2001 Award Software Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving ESC:Quit :Select Item Quit Without Saving (Y/N)? N F8: Q-Flash F10:Save & Exit Setup Abandon all Data Figure 15: Exit Without Saving Type Y will quit the Setup Utility without saving to RTC CMOS. Type N will return to Setup Utility. 56
Revision History Intel Pentuim 4 2.0GHz (128 x 2) MB RAM (NANYA NT5DS16M8AT-7K S) CPU 256KB Gigabyte GV-GF3000D (NUCD 1.9) IDE (Quantum AS30000AT 30GB) Windows 2000+ SP2+DX 8.0a Display Driver at 1024 x 768 x 64K colors x 75Hz IUCD ver. 19 For Intel chipset M.B. Processor Intel Pentium 4 2GHz (100x20) WCPUID 3.0D Clock Frequency Internal MHz 2019.88 External MHz 100.99 SiSoft Sandra 2001 CPU/FPU Benchmark 3895/2484 CPU Multi-Media Benchmark 8025/9945 Drives Benchmark 20663 Memory Benchmark 1015/1073 SPECviewperf 6.12 Pro CDRS-03 14.76 MedMCAD-01 30.19 Light-04 8.283 DX-06 27.13 DRV-07 18.18 Awadvs-04 62.11 QUAKE III Arena (without sound) 640*480*16 Demo1 199.2 1024*768*32 Demo2 181.2 3D Mark 2001 1.0 6852 55
GA-8IRM Pentium 4 CPU CPUCLK± (100MHz) AGPCLK (66MHz) 3 PCI PCICLK (33MHz) AGP 4X RJ45 Creative CT5880 Game Port Intel 82562ET* AC97 Link AC97 CODEC Intel 82845 Intel ICH 2 4 USB Ports System Bus 100MHz 100/133 MHz HCLK± (100MHz) MCHCLK (66MHz) 66 MHz 33 MHz 14.318 MHz 48 MHz LPC BUS ATA33/66/100 IDE Channels Winbond W83627HF FWH SST49LF002 24 MHz 33 MHz SDRAM Game Port Floppy LPT Port PS/2 KB/Mouse COM Ports MIC LINE-IN PCICLK (33MHz) USBCLK (48MHz) 14.318 MHz 33 MHz LINE-OUT Cypress CY28324 * GA-8IRML. HCLK± (100MHz) CPUCLK± (100MHz) AGPCLK (66MHz) MCHCLK (66MHz) ICH3V66 (66MHz) 56
Easy TuneIII TM EasyTuneIII TM EasyTuneIII TM EasyTuneIII TM BIOS Jumpers Switches " " EasyTuneIII TM EasyTune III TM CPU EasyTuneIII TM http://www.gigabyte.com.tw : IUCD 1.6 EasyTuneIII TM 57
GA-8IRM @ BIOS TM @BIOS TM BIOS EasyTune III TM DOS BIOS Windows @BIOS TM BIOS @BIOS TM BIOS @BIOS TM Internet BIOS BIOS Windows BIOS! @BIOS TM BIOS 58
Revision History Windows ME ( 1.9) ( " " setup.exe ) A. Installing Intel 845 Chipset Driver INF. Intel INF B. Installing Sound Driver,. C. Installing LAN Driver*,. A: Intel 845. A-1. Windows 9x/ME/2000/XP INF "Windows 9x/ME/2000/XP INF Update Utility". A-2. Intel Ultra ATA Storage "Intel Ultra ATA Storage Driver". * GA-8IRML. 5 9
GA-8IRM B AC97 Revision History 1.9 "Audio" 1. "RealTek AC 97 Audio Driver". C Intel 82562 Network * (8IRM ) Revision History "Intel 82562 Network Driver" Windows ME LAN (README.txt) D:\Network\Rtl ( D:) "NETWORK" "Driver Information" * GA-8IRML. 6 0
Revision D History EasyTuneIII ( " " setup.exe ) " Tools" 2. "Easy Tune III Setup" 1. "Gigabyte Utilities" (1) (2) 4. "Next" 3. "Next" (4) (3) 6 1
GA-8IRM 5. "Next" 6. "Next" (5) (6) 7. "Finish" (7) (8) 6 2
E BIOS BIOS OS Win9X @BIOS " Tools" 2. "@BIOS Writer Utility v1.08e" 1. "Gigabyte Utilities" (1) (2) " " (3) 1. I. Internet BIOS a. "Internet Update" b. "Update New BIOS" c. @BIOS ( "Gigabyte @BIOS server 1 in Taiwan" "Gigabyte @BIOS server 2 in Taiwan") d. e. BIOS 6 3
GA-8IRM II. Internet BIOS a. "Internet Update" b. "Update New BIOS" c. " "All Files (*.*)" d. BIOS ( : 8ITXE.F1) e. III. BIOS "Save Current BIOS" BIOS IV. Flash ROM "About this program" @BIOS Flash ROM 2. a. I ( ) BIOS b. II BIOS c. I @BIOS BIOS BIOS II BIOS d. BIOS 6 4
GA-7VTX Flash841 BIOS DOS BIOS Flash BIOS ( ) (1) "BIOS Feature Setup" "BIOS Flash Protection" Auto 32 (2) Winzip pkunzip winzip : http://shareware.cnet.com ( ) DOS ( Windows 98 ) Windows ME/2000 DOS (1) ( " ") " " "3.5 (A)" " " 6 5
GA-8IRM (2) " ( )" " " " " " " (3) " " 6 6
( ) BIOS BIOS (1) (http://www.gigabyte.com.tw/chinese-web/index.html) " " (2) " BIOS & Driver" 6 7
GA-8IRM (3) GA-7VTX BIOS (4) ( F4) " " " " 6 8
(5) "Extract" (6) ( ) A "Extract" 6 9
GA-8IRM ( ) (1) ( ) A "DEL" BIOS Setup American Release:09/16/99 Megatrends AMIBIOS (C) 1999 American Megatrend 7VTX F1 Check System Health OK AMD-Athlon(tm)Processor-900MHz Checking NVRAM... 262144KB Wait... Press F1 to enter Dual BIOS Utility. Press ESC to quit Press any key to contiune ( C ) American Megatrends Inc., 63-0001-001199-00101111-071595-VIA_K7-GA7VTX1-F (2) BIOS FEATUERS SETUP AMIBIOS SIMPLE SETUP UTILITY - VERSION 1.24b (C) 1999 American Megatrends, Inc. All Rights Reserved STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP HARDWARE MONITOR & MISC SETUP CHIPSET FEATURES SETUP SUPERVISOR PASSWORD POWER MANAGEMENT SETUP USER PASSWORD PNP / PCI CONFIGURATION IDE HDD AUTO DETECTION LOAD BIOS DEFAULTS SAVE & EXIT SETUP LOAD SETUP DEFAULTS EXIT WITHOUT SAVING ESC: Quit : Select Item (Shift)F2 : Change Color F5: Old Values F6: Load BIOS Defaults F7: Load Setup Defaults F10:Save & Exit Time, Date, Hard Disk Type 7 0
( ) (1) ( ) A "DEL" BIOS Setup American Release:09/16/99 Megatrends AMIBIOS (C) 1999 American Megatrend 7VTX F1 Check System Health OK AMD-Athlon(tm)Processor-900MHz Checking NVRAM... 262144KB Wait... Press F1 to enter Dual BIOS Utility. Press ESC to quit Press any key to contiune ( C ) American Megatrends Inc., 63-0001-001199-00101111-071595-VIA_K7-GA7VTX1-F (2) BIOS FEATUERS SETUP AMIBIOS SIMPLE SETUP UTILITY - VERSION 1.24b (C) 1999 American Megatrends, Inc. All Rights Reserved STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP HARDWARE MONITOR & MISC SETUP CHIPSET FEATURES SETUP SUPERVISOR PASSWORD POWER MANAGEMENT SETUP USER PASSWORD PNP / PCI CONFIGURATION IDE HDD AUTO DETECTION LOAD BIOS DEFAULTS SAVE & EXIT SETUP LOAD SETUP DEFAULTS EXIT WITHOUT SAVING ESC: Quit : Select Item (Shift)F2 : Change Color F5: Old Values F6: Load BIOS Defaults F7: Load Setup Defaults F10:Save & Exit Time, Date, Hard Disk Type 7 1
GA-8IRM ( ) BIOS (1) A:\> dir/w "Enter" A:\> "BIOS " "BIOS " "Flash841 7VTX.F4" "Enter" Starting Windows 98 Microsoft(R) Windows98 Copyright Microsoft Corp 1981-1999 A:\> dir/w Volume in drive A has no label Volume Serial Number is 16EB-353D Directory of A:\ COMMAND.COM 7VTX.F4 FLASH841.EXE 3 file(s) 838,954 bytes 0 dir(s) 324,608 bytes free A:\> Flash841 7VTX.F4 (2) [Enter] Load [Drive:\Path\Filename] [Enter] 7 2
(3) BIOS [Enter] [Esc] BIOS BIOS Are you sure to flash the BIOS? [Enter] to continue Or [Esc] to cancel? (4) BIOS [ESC] EXIT? [Enter] to continue Or [Esc] to cancel? 7 3
GA-8IRM ( ) BIOS BIOS (1) BIOS American Release:09/16/99 Megatrends AMIBIOS (C) 1999 American Megatrend 7VTX F4 Check System Health OK AMD-Athlon(tm)Processor-900MHz Checking NVRAM... 262144KB Wait... Press F1 to enter Dual BIOS Utility. Press ESC to quit Press any key to contiune ( C ) American Megatrends Inc., 63-0001-001199-00101111-071595-VIA_K7-GA7VTX1-F (2) <DEL> BIOS "LOAD SETUP DEFAULTS" "Enter" "Y" "Enter" AMIBIOS SIMPLE SETUP UTILITY - VERSION 1.24b (C) 2001 American Megatrends, Inc. All Rights Reserved STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP HARDWARE MONITOR & MISC SETUP CHIPSET FEATURES SETUP SUPERVISOR PASSWORD POWER MANAGEMENT SETUP USER PASSWORD PNP / PCI CONFIGURATION Load Setup Defaults? (Y/N)?N IDE HDD AUTO DETECTION LOAD BIOS DEFAULTS SAVE & EXIT SETUP LOAD SETUP DEFAULTS EXIT WITHOUT SAVING ESC: Quit : Select Item (Shift)F2 : Change Color F5: Old Values F6: Load BIOS Defaults F7: Load Setup Defaults F10:Save & Exit Load Setup Defaults 7 4