DETAIL SPECIFICATION SHEET CONNECTORS, RECEPTACLE, ELECTRICAL, FLANGE MOUNTING, MINIATURE, CLASSES E, F, G AND R Inactive for new design for 14 November 1977.For new design, use MIL-DTL-83723, series III, which is interchangeable. INCH-POUND 20 August 2009 SUPERSEDING MS24264P 6 February 2004 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-26500. FIGURE 1. Receptacle, threaded for classes F, G and R. AMSC N/A FSC 5935
STYLE S (SOCKET INSERT) FIGURE 1. Receptacle, threaded for classes F, G and R Continued. 2
FIGURE 1. Receptacle, threaded for classes F, G and R Continued. 3
Inches mm Inches mm.015 0.38.153 3.89.018 0.46.155 3.94.019 0.48.169 4.29.020 0.51.281 7.14.022 0.56.306 7.77.024 0.61.322 8.18.031 0.79.378 9.60.045 1.14.392 9.96.052 1.32.490 12.45.054 1.37.491 12.47.072 1.83.520 13.21.078 1.98.560 14.22.100 2.54.708 17.98.125 3.18.728 18.49.133 3.38 1.421 36.09.140 3.56 NOTES: 1. Dimensions in inches. Unless otherwise specified, tolerances on decimals is.005. 2. Metric equivalents are given for information only. 3. Use tool MIL-I-81969/17 to assemble contacts into this connector, and use tool MIL-I-81969/19 to remove contacts from this connector. 4. All diameters to be concentric with each other within.015 T.I.R. All diameters in the same plane to be concentric with each other within.004 T.I.R. 5. Distance between end of shell and the point at which a gauge pin having the same basic diameter as the mating contact and a square face, engages socket contact spring. 6. Dimensions on pin and socket contact locations and end of shell to insert faces apply when contacts are placed in inserts for inspection or application. 7. Dimension.133 may reduce to.118 minimum under pressures caused by molded cable assemblies or sharp cable bends. 8. Thread relief groove is optional on shell. When groove is omitted the length of full thread from front of shell will be.310 minimum and thread run out.385 maximum. 9. Thread relief groove is optional on shell. When groove is omitted, the length of full thread from rear of shell will be.221 minimum. 10. Environment resistant (classes F and R) receptacles, type T aluminum shell material. Grounding environment resistant (class G) receptacles, type T aluminum shell material. Environment resistant (class E) receptacles, type T stainless steel shell material. These receptacles mate with plug MS24266 type T. 11. True position (T.P.) tolerances specified are for maximum material conditions (M.M.C). FIGURE 1. Receptacle, threaded for classes F, G and R Continued. 4
FIGURE 2. Receptacle, optional shell design for classes F, G, R and stainless steel shell design for class E. 5
Inches mm.015.38.025.63.073 1.85.086 2.18.161 4.09.220 5.59.281 7.14.418 10.62 1.125 28.57 1.375 34.92 NOTES: 1. Dimensions in inches. Unless otherwise specified, tolerances on decimals is.005. 2. Metric equivalents are given for information only. 3. Use tool MIL-I-81969/17 to assemble contacts into this connector, and use tool MIL-I-81969/19 to remove contacts from this connector. 4. All diameters to be concentric with each other within.015 T.I.R. All diameters in the same plane to be concentric with each other within.004 T.I.R. 5. Distance between end of shell and the point at which a gauge pin having the same basic diameter as the mating contact and a square face, engages socket contact spring. 6. Dimensions on pin and socket contact locations and end of shell to insert faces apply when contacts are placed in inserts for inspection or application. 7. Dimension.133 may reduce to.118 minimum under pressures caused by molded cable assemblies or sharp cable bends. 8. Thread relief groove is optional on shell. When groove is omitted the length of full thread from front of shell will be.310 minimum and thread run out.385 maximum. 9. Thread relief groove is optional on shell. When groove is omitted, the length of full thread from rear of shell will be.221 minimum. 10. Environment resistant (classes F and R) receptacles, type T aluminum shell material. Grounding environment resistant (class G) receptacles, type T aluminum shell material. Environment resistant (class E) receptacles, type T stainless steel shell material. These receptacles mate with plug MS24266 type T. 11. True position (T.P.) tolerances specified are for maximum material conditions (M.M.C). FIGURE 2. Receptacle, optional shell design for classes F, G, R and stainless steel shell design for class E Continued. 6
FIGURE 3. Receptacle, bayonet, optional design. 7
FIGURE 3. Receptacle, bayonet, optional design - Continued. 8
FIGURE 3. Receptacle, bayonet optional design - Continued. 9
Inches mm.004.10.005.13.010.25.155 3.94.169 4.29.368 9.35.376 9.55.378 9.6.392 9.96.540 13.72.560 14.22 NOTES: 1. Dimensions in inches. Unless otherwise specified, tolerances on decimals is.005. 2. Metric equivalents are given for general information only. 3. Use tool MIL-I-81969/17 to assemble contacts into this connector, and use tool MIL-I-81969/19 to remove contacts from this connector. 4. All diameters to be concentric with each other within.015 T.I.R. All diameters in the Same plane to be concentric with each other within.004 T.I.R. 5. Distance between end of shell and the point at which a gauge pin having the same basic diameter as the mating contact and a square face, engages socket contact spring. 6. Dimension on pin and socket contact locations and end of shell to insert faces apply when contacts are placed in inserts for inspection or application. 7. Dimension.133 may reduce to.118 minimum under pressures caused by molded cable assemblies or sharp cable bends. 8. Environment resistant (classes F and R) receptacles, type B aluminum shell material. Grounding environment resistant (class G) receptacles, types B-aluminum shell material. Environment resistant (class E) receptacles, types B-stainless steel shell material. This receptacle mates with plug MS24266 type B. 9. True position (T.P.) tolerances specified are for maximum material conditions (M.M.C.). FIGURE 3. Receptacle, bayonet optional design - Continued. 10
11 Shell size A UNEF-2A coupling B dia C dia +.005 (0.13) -.000 (0.00) E max Insert dia F UNEF-2A access 8.5625-24 (14.27).508 (12.90).428 (10.87).318 (8.08).4375-28 (11.10) 10.6875-24 (17.45).636 (16.15).530 (13.46).394 (10.01).5625-24 (14.27) 12.875-20 (22.22).806 (20.47).700 (17.78).564 (14.33).750-20 (19.05) 14.9375-20 (23.80).875 (22.22).769 (19.53).633 (16.08).8125-20 (20.62) 16 1.0625-18 (26.97) 1.002 (25.45).896 (22.76).760 (19.30).9375-20 (23.80) 18 1.1875-18 (30.15) 1.108 (28.62) 1.002 (25.45).866 (22.00) 1.0625-18 (26.97) 20 1.3125-18 (33.32) 1.233 (31.32) 1.127 (28.62).991 (25.17) 1.1875-18 (30.15) 22 1.4375-18 (36.50) 1.358 (34.49) 1.252 (31.80) 1.116 (28.35) 1.3125-18 (33.32) 24 1.5625-18 (39.67) 1.483 (37.67) 1.377 (34.98) 1.241 (31.52) 1.4375-18 (36.50) FIGURE 4. Receptacle dimensions. 029-88256270 029-88257182 www.forpn.com sales@forpn.com
12 Shell size F 1-36NS-2A F 1 pitch dia FF max dia G max dia 8.4340 (11.024).4151/.4114 (10.544/10.450).437 (11.10).561 (14.25) 10.5634 (14.310).5454/.5415 (13.853/13.754).562 (14.27).696 (17.68) 12.7334 (18.628).7154/.7115 (18.171/18.072).750 (19.50).875 (22.22) 14.8032 (20.401).7841/.7806 (19.961/19.827).812 (20.62).935 (23.75) 16.9302 (23.627).9110/.9074 (23.134/23.048).938 (23.82) 1.062 (26.97) 18 1.0362 (26.319) 1.0171/1.0134 (25.834/25.740) 1.062 (26.97) 1.187 (30.15) 20 1.1611 (29.492) 1.1431/1.1385 (29.034/28.918) 1.182 (30.02) 1.312 (33.32) 22 1.2862 (32.669) 1.2670/1.2633 (32.182/32.088) 1.312 (33.32) 1.437 (36.50) 24 1.4111 (35.842) 1.3931/1.3885 (35.385/35.268) 1.432 (36.37) 1.562 (39.67) FIGURE 4. Receptacle dimensions Continued. 029-88256270 029-88257182 www.forpn.com sales@forpn.com
Shell size H min dia front mounting hole HH max grommet dia J min dia back mounting hole KK dia +.000 (0.00) -.005 (0.13) L mounting hole LL dia +.000 (0.00) -.009 (0.23) 8.447 (11.35).328 (8.33).620 (15.75).536 (13.61).594 (15.09).125 (3.18) 10.572 (14.53).420 (10.67).748 (19.00).659 (16.74).719 (18.26).125 (3.18) 12.760 (19.30).580 (14.73).913 (23.19).829 (21.06).812 (20.62).125 (3.18) 14.822 (20.88).664 (16.86).980 (24.90).898 (22.81).906 (23.01).125 (3.18) 16.948 (24.08).769 (19.53) 1.107 (28.12) 1.025 (26.03).969 (24.61).125 (3.18) 18 1.072 (28.12).902 (22.91) 1.209 (30.71) 1.131 (28.73) 1.062 (26.97).125 (3.18) 20 1.192 (30.28) 1.033 (26.24) 1.337 (33.96) 1.256 (31.90) 1.156 (29.36).125 (3.18) 22 1.322 (33.58) 1.152 (29.26) 1.452 (36.89) 1.381 (35.08) 1.250 (31.75).125 (.318) 24 1.442 (36.63) 1.282 (32.56) 1.577 (40.055) 1.505 (38.25) 1.375 (34.925).154 (3.91) FIGURE 4. Receptacle dimensions Continued. 13
Shell size M length side N +.000 (0.00) -.004 (0.10) NN +.000 (0.00) -.004 (0.10) P +.000 (0.00) -.005 (0.13) UU +.000 (0.00) +.009 (0.23) 8.812 (20.62).101 (2.56).078 (1.93).076 (1.93).310 (7.87) 10.937 (23.80).094 (2.39).093 (2.36).089 (2.26).374 (9.50) 12 1.031 (26.19).094 (2.39).093 (2.36).089 (2.26).459 (11.66) 14 1.125 (28.58).094 (2.39).093 (2.36).089 (2.26).494 (12.55) 16 1.250 (31.76).094 (2.39).093 (2.36).089 (2.26).557 (14.15) 18 1.343 (34.11).094 (2.39).093 (2.36).089 (2.26).610 (15.49) 20 1.437 (36.50).094 (2.39).093 (2.36).089 (2.26).673 (17.09) 22 1.562 (39.67).094 (2.39).093 (2.36).089 (2.26).735 (18.67) 24 1.703 (43.26).094 (2.39).093 (2.36).089 (2.26).798 (20.27) Position Shell size 8 Shell size 10 Shell sizes 12 thru 24 E F G E F G E F G Normal 60 180 300 60 180 300 50 170 290 6 46 166 286 46 166 286 50 170 290 7 46 166 286 46 166 286 50 170 290 8 60 180 300 60 180 300 50 170 290 9 89 209 329 89 209 329 50 170 290 Y - - - 60 180 300 50 170 290 NOTES: 1. Dimensions are in inches. 2. Metric equivalent are given for information only. FIGURE 4. Receptacle dimensions Continued. 14
Weight chart Maximum connector weight in lbs MS PIN Pin insert Less contacts With contacts 8T2PN.023 (0.58).025 (0.64) 10T2PN.039 (0.99).041 (1.04) 10T5PN.038 (0.96).042 (1.07) 10T20PN.038 (0.96).042 (1.07) 12T3PN.053 (1.35).058 (1.47) 12T12PN.051 (1.30).061 (1.55) 14T3PN.057 (1.48).067 (1.70) 14T4PN.057 (1.48).072 (1.83) 14T7PN.057 (1.48).070 (1.78) 14T12PN.057 (1.48).070 (1.78) 14T15PN.057 (1.48).071 (1.80) 16T10PN.067 (1.70).085 (2.16) 16T24PN.067 (1.71).087 (2.21) 18T8PN.081 (2.06).110 (2.79) 18T11PN.079 (2.01).103 (2.62) 18T14PN.080 (2.03).105 (2.67) 18T31PN.079 (2.01).105 (2.67) 20T16PN.095 (2.41).123 (3.12) 20T25PN.092 (2.34).130 (3.30) 20T28PN.093 (2.36).128 (3.25) 20T39PN.093 (2.36).128 (3.25) 20T41PN.093 (2.36).127 (3.22) 22T12PN.106 (2.69).149 (3.78) 22T19PN.108 (2.74).142 (3.61) 22T32PN.109 (2.77).152 (3.86) 22T55PN.104 (2.64).151 (2.16) 24T43PN.126 (3.20).181 (4.60) 24T57PN.125 (3.18).178 (4.52) 24T61PN.123 (3.12).174 (4.42) FIGURE 5. Weights for threaded connectors, classes F, G and R. 15
MS PIN Weight chart Maximum connector weight in lbs Socket insert Less contacts With contacts 8T2SN.024 (0.61).026 (0.66) 10T2SN.040 (1.02).042 (1.07) 10T5SN.039 (0.99).043 (1.09) 10T20SN.040 (1.02).044 (1.12) 12T3SN.055 (1.40).060 (1.52) 12T12SN.052 (1.32).062 (1.57) 14T3SN.063 (1.60).072 (1.83) 14T4SN.059 (1.50).074 (1.88) 14T7SN.059 (1.50).072 (1.83) 14T12SN.059 (1.50).072 (1.83) 14T15SN.059 (1.50).072 (1.83) 16T10SN.071 (1.80).089 (2.26) 16T24SN.070 (1.78).090 (2.29) 18T8SN.084 (2.13).112 (2.84) 18T11SN.081 (2.06).104 (2.64) 18T14SN.084 (2.13).109 (2.77) 18T31SN.083 (2.11).108 (2.74) 20T16SN.100 (2.54).128 (3.25) 20T25SN.097 (2.46).134 (3.40) 20T28SN.097 (2.46).131 (3.33) 20T39SN.097 (2.46).131 (3.33) 20T41SN.097 (2.46).131 (3.33) 22T12SN.111 (2.82).153 (3.89) 22T19SN.115 (2.92).148 (3.76) 22T32SN.116 (2.95).159 (4.04) 22T55SN.110 (2.79).155 (3.94) 24T43SN.134 (3.40).188 (4.78) 24T57SN.130 (3.30).182 (4.62) 24T61SN.128 (3.25).178 (4.52) FIGURE 5. Weights for threaded connectors, classes F, G and R Continued. 16
REQUIREMENTS Insert arrangements and alternate insert keying positions shall be in accordance with MIL-STD-1554. Dimensions and configurations: See figures 1 through 5. Connector mating: This connector mates with MS24266 and MS27615. Contacts: In accordance with SAE-AS39029. For accessories used with this connector, see MIL-DTL-26500. Part or Identifying Number (PIN) example: MS number Class Shell size Coupling type Contact arrangement Style Polarizing position ( N used for normal position) MS24264 R 18 B 31 P 6 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-26500, this document references the following: SAE-AS39029 MIL-DTL-83723 MIL-I-81969/17 MIL-I-81969/19 MIL-STD-1554 MS24266 MS27615 17
CONCLUDING MATERIAL Custodians: Air Force 85 DLA CC Review activity: Air Force 99 Preparing activity: DLA CC (Project 5935 2009-099) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil. 18