RoHS Specification 规格书 Customer Name: 客户名称 : Customer P/N: 客户品号 : Factory P/N: HL-AA-280S29YC-D 公司品号 : Sending Date: 送样日期 : Client approval Hongli approval 客户审核 鸿利光电审核 Approval 核准 Audit 确认 Confirmation 制作 Approval 核准 Audit 确认 Confirmation 制作 殷小平 谭娅 Qualified 接受 Disqualified 不接受 DATE: 日期 : Adr:Airport High-tech Industry Base Jinggu South Road(XianKe st Road Intersection), Huadu District,Guangzhou,China 地址 : 中国广州市花都区机场高新科技产业基地金谷南路与先科一路交汇 Tel/ 电话 :020-86733333 Fax/ 传真 :020-86733883 86733938 86733265 Web/ 网址 :www.honglitronic.com 注 :. 此规格书以中英文方式书写, 若有冲突以中文版本为准文本. 2. 此规格书的最终解释权归广州鸿利光电股份有限公司 3. 此规格书的有效期限为两年, 自盖章或签字之日起计算, 期满时双方可以续签协议, 但应采用书面形式 SPEC NO:B--A-007 REV NO: A/2 DATE: SEP/24/202 PAGE: OF 8
.28 [0.05].20 [0.05] 0.28 [0.0] 0.70 [0.03].00 [0.04] 0.55 [0.02].20 [0.05] HL-AA-280S29YC-D Features( 特征 ) Side view LED( 侧发光 LED) Extremely wide viewing angle.( 宽的发光角度 ) Suitable for all SMT assembly and solder process.( 适用于所有的 SMT 组装和焊接工艺 ) Available on tape and reel.( 适用于载带及卷轴 ) Moisture sensitivity level: Level 4.( 防潮等级 Level 4) Package:3000pcs/reel..( 包装每卷 3000PCS) RoHS compliant. (RoHS 认证 ) Description( 描述 ) The YELLOW source color devices are made with AlGaInP on Substrate Light Emitting Diode 黄光 LED 由 AlGaInP 四种元素芯片激发而成 ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES 注意 : 操作时应注意静电敏感 释放设备装置 Applications( 应用 ) Optical indicator( 光学指示 ) Package Dimensions( 封装尺寸 ) Indoor display( 室内显示 ) Automotive lighting( 汽车照明 ) Backlight for LCD, switch and Symbol, display (LCD 背光 转换器, 开关和标志, 显示器等 ) Tubular light application( 用于日光灯管 ) 2 General use( 一般应用 ) 2.80 [0.] 2.45 [0.0] Recommended Soldering Pattern ( 建议焊盘尺寸图 ) 2.40 [0.06] 3.20 0.55 [0.3] [0.02] 2.40 [0.06].40 [0.06] 2 Notes:( 备注 ) 2.00 [0.08] 2.00 [0.08]. All dimension units are millimeters.( 所有标注尺寸单位为毫米 ).40 [0.06] 2.All dimension tolerance is ±0.5mm unless otherwise noted.( 除特别标注外, 所有尺寸允许公差 ±0.5mm ) SPEC NO:B--A-007 2.00 [0.08] REV NO: 2.00 A/2 [0.08] DATE: SEP/24/202 PAGE: 2 OF 8
HL-AA-280S29YC-D Selection Guide( 选择指南 ) Part No. 型号 Dice Lens Type 胶体类型 Luminous intensity(mcd) 光强 @ 20mA Viewing Angle 角度 Min Typ 2q/2 HL-AA-280S29YC-D Yellow (AlGaInP) Water Clear 90 20 90 Note:( 备注 ) /2 is the angle from optical centerline where the luminous intensity is /2 the optical centerline value. q/2 是半值角, 指光强是光学中心线光强的 /2 处到光学中心线的角度 2. the above luminous intensity measurement allowance tolerance ±0%. 上述发光强度的测试允许公差为 ±0% Electrical / Optical Characteristics at Ta=25 C 电性与光学特性 Parameter( 参数 ) Symbol ( 符号 ) Min. ( 最小 ) Typ. ( 平均 ) Max. ( 最大 ) Units ( 单位 ) Test Conditions 测试条件 Forward Voltage 正向电压 Reverse Current 反向电流 Dominate Wavelength 主波长 VF.8 - - 2.4 V IF=20mA IR - - - - 0 μa VR = 5V λd 586 - - 596 nm IF=20mA Absolute Maximum Ratings at Ta=25 C 绝对最大额定值 Parameter( 参数 ) Symbol( 符号 ) Rating( 值 ) Units( 单位 ) Power Dissipation( 功耗 ) Pd 75 mw Forward Current( 正向电流 ) IF 30 ma Peak Forward Current []( 峰值正向电流 ) IFP 40 ma Reverse Voltage( 反向电压 ) VR 5 V Electrostatic Discharge (HBM)( 静电 ) ESD 2000 V Operating Temperature( 操作温度 ) Topr -40 ~ +85 Storage Temperature( 保存温度 ) Tstg -40 ~ +00 Note:( 备注 ). /0 Duty cycle, 0.ms pulse width.( 脉宽 0.ms, 周期 /0) 2. The above forward voltage measurement allowance tolerance is ± 0.V.( 以上所示电压测量误差 ± 0.V) SPEC NO:B--A-007 REV NO: A/2 DATE: SEP/24/202 PAGE: 3 OF 8
Relative luminous intensity Forward Current(mA) Relative Luminous Intensity Forward Current(mA) Relative Luminous Intensity HL-AA-280S29YC-D Typical optical characteristics curves 典型光学特性曲线 Ambient Temperature vs. Forward Current 环境温度与正向电流特性曲线 Forward Current VS. Relative Intensity 正向电流与相对光强特性曲线 60 2.5 50 40 30 20 0 2.0.5.0 0.5 0 0 20 40 60 80 00 Ambient Temperature Ta( ) 0.0 0 0 20 30 40 50 Forward Current(mA) Forward Voltage VS. Forward Current 正向电压与正向电流特性曲线 40 Ambient Temperature VS. Relative Intensity 环境温度与相对光强特性曲线 3.0 2.5 30 2.0 20.5 0.0 0.5 0 0.0 0.5.0.5 2.0 2.5 3.0 Forward Voltage(V) Relative spectral emission 相对光谱分布特性曲线 0.0-40 -20 0 20 40 60 80 Ambient Temperature Radiation diagram 辅射图特性曲线 Ta( ).0 0.8 0.6 0.4 0.2 0.0 380 460 540 620 700 780 Wavelength(nm) SPEC NO:B--A-007 REV NO: A/2 DATE: SEP/24/202 PAGE: 4 OF 8
HL-AA-280S29YC-D Reliability Test Items And Conditions 信赖性测试项目及条件 Test Items 项目 Ref.Standard 参考标准 Test Condition 测试条件 Time 时间 Quantity 数量 Ac/Re 接收 / 拒收 Reflow 回流焊 JESD22-B06 Temp:260 max T=0 sec 3 times. 22Pcs. 0/ Temperature Cycle 温度循环 JESD22-A04 00 ±5 30 min. 5 min -40 ±5 30 min. 00 Cycles 22Pcs. 0/ High Temperature Storage 高温保存 JESD22-A03 Temp:00 ±5 000Hrs. 22Pcs. 0/ Low Temperature Storage 低温保存 JESD22-A9 Temp:-40 ±5 000Hrs. 22Pcs. 0/ Life Test 常温通电 JESD22-A08 Ta=25 ±5 IF=20mA 000Hrs. 22Pcs. 0/ High Temperature High Humidity JESD22-A0 85 ±5 / 85%RH IF=5mA 000Hrs. 22Pcs. 0/ Criteria For Judging Damage 失效判定标准 Test Items 项目 Symbol 符号 Test Condition 测试条件 Criteria For Judgement 判定标准 Min. 最小 Max. 最大 Forward Voltage 正向电压 Reverse Current 反向电流 Luminous Flux 光通量 VF IF=20mA - - U.S.L*)x. IR VR = 5V - - U.S.L*)x2.0 lm IF=20mA L.S.L*)x0.7 - - U.S.L: Upper standard level 规格上限 L.S.L: Lower standard level 规格下限 *The technical information shown in the data sheets are limited to the typical characteristics and circuit examples of the referenced products. It does not constitute the warranting of industrial property nor the granting of any license. 数据工作表中所示的技术信息仅限于典型特征和电路实例引用的产品. 它既不构成工业特性的保证, 也不构成任何许 可的授权 SPEC NO:B--A-007 REV NO: A/2 DATE: SEP/24/202 PAGE: 5 OF 8
HL-AA-280S29YC-D SMT Reflow Soldering Instructions SMT 回流焊说明.Reflow soldering should not be done more than two times. 回流焊不可以做两次以上 2.When soldering, do not put stress on the LEDs during heating 当焊接时, 不要在材料受热时用力压胶体表面 Soldering iron 烙铁焊接.When hand soldering, keep the temperature of iron below less 300 less than 3 seconds 当手工焊接时, 烙铁的温度必须小于 300, 时间不可超过 3 秒 2.The hand solder should be done only one times 手工焊接只可焊接一次 Repairing 修补 Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed in advance whether the characteristics of LEDs will or will not be damaged by repairing. LED 回流焊后不应该修复, 当修复是不可避免时, 必须使用双头烙铁 ( 如下图 ), 但必须事先确认此种方式会或不会 损坏 LED 本身的特性 SPEC NO:B--A-007 REV NO: A/2 DATE: SEP/24/202 PAGE: 6 OF 8
HL-AA-280S29YC-D Handling Precautions 处理防备措施 Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more prone to damage by external mechanical force. As a result, Special handling precautions must be observed during assembling using silicone encapsulated LED products, Failure to comply might leads to damage and premature failure of the LED. 相对环氧树脂较脆较硬而言, 硅胶封装较柔软且有弹性, 虽然它的特性大大减少了热应力, 但易受机械外力损坏, 因此 在手工处理方面须要对硅胶封装材料做预防措施, 若未按要求操作, 可能会导致 LED 损坏和光衰.Handle the component along the side surface by using forceps or appropriate tools 通过使用适当的工具从材料侧面夹取 2.Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry 3528 不可直接用手或尖锐金属压胶体表面, 它可能会损坏内部电路 3.Do not available for flexible products( like soft flexible strip) or damage the internal circuitry 不适用于易弯曲产品 ( 如软光条 ) 以防内部电路受损 4.LED operating environment and sulfur element composition cannot be over 00PPM in the LED mating usage material LED 工作环境及与 LED 适配的材料中硫元素及化合物成份不可超过 00PPM SPEC NO:B--A-007 REV NO: A/2 DATE: SEP/24/202 PAGE: 7 OF 8
HL-AA-280S29YC-D Label 标签 IV: Luminous intensity rank 亮度等级 WD: Dominate Wavelength 波长等级 VF: Forward voltage rank 电压等级 Tape Specifications (Units : mm) 载带规格 ( 单位 :mm) Reel Dimensions 卷轴尺寸 Moisture Resistant Packaging 防潮带包装 Note: The tolerances unless mentioned is ±0.mm, Unit: mm 注 : 标注公差为 ±0.mm, 单位 :mm SPEC NO:B--A-007 REV NO: A/2 DATE: SEP/24/202 PAGE: 8 OF 8