HL-A-2835D1W-S1-08-HR3（主推）

Size: px

Start display at page:

Download "HL-A-2835D1W-S1-08-HR3（主推）"

露耿
5 years ago
Views:

1 RoHS Specification 规格书 Customer Name: 客户名称 : Customer P/N: 客户品号 : Factory P/N: HL-A-2835D1W-S1-08-HR3 公司品号 : Sending Date: 送样日期 : Client approval Hongli approval 客户审核鸿利光电审核 Approval 核准 Audit 确认 Confirmation 制作 Approval 核准 Audit 确认 Confirmation 制作黄雪梅 Qualified 接受 Disqualified 不接受 DATE: 日期 : Adr:Airport High-tech Industry Base Jingu South Road(XianKe 1st Road Intersection), Huadu District,Guangzhou,China 地址 : 中国广州市花都区机场高新科技产业基地金谷南路与先科一路交汇 Tel/ 电话 : Fax/ 传真 : Web/ 网址 : 注 :1. 此规格书以中英文方式书写, 若有冲突以中文版本为准文本. 2. 此规格书的最终解释权归广州鸿利光电股份有限公司 3. 此规格书的有效期限为两年, 自盖章或签字之日起计算, 期满时双方可以续签协议, 但应采用书面形式 SPEC NO:B-13-A-0728 REV NO: A/6 DATE: OCT/31/2015 PAGE: 1 OF 14

Features( 特征 ) PLCC-2 Package.(PLCC-2 封装 ) Extremely wide viewing angle.( 宽的发光角度 ) Suitable for all SMT assembly and solder process.( 适用于所有的 SMT 组装和焊接工艺 ) Available on tape and reel.

2 Features( 特征 ) PLCC-2 Package.(PLCC-2 封装 ) Extremely wide viewing angle.( 宽的发光角度 ) Suitable for all SMT assembly and solder process.( 适用于所有的 SMT 组装和焊接工艺 ) Available on tape and reel.( 适用于载带及卷轴 ) Moisture sensitivity level: Level 4.( 防潮等级 Level 4) Package:4000pcs/reel..( 包装每卷 4000PCS) RoHS compliant. (RoHS 认证 ) Description( 描述 ) The White LED which was fabricated using a blue chip and the phosphor 白光 LED 由蓝光芯片与荧光粉激发而成 ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES 注意 : 操作时应注意静电敏感释放设备装置 Applications( 应用 ) Optical indicator( 光学指示 ) Indoor display( 室内显示 ) Package Dimensions( 封装尺寸 ) Automotive lighting( 汽车照明 ) Backlight for LCD, switch and Symbol, display (LCD 背光转换器, 开关和标志, 显示器等 ) Tubular light application( 用于日光灯管 ) General use( 一般应用 ) Recommended Soldering Pattern ( 建议焊盘尺寸图 ) Notes:( 备注 ) 1. All dimension units are millimeters.( 所有标注尺寸单位为毫米 ) 2.All dimension tolerance is ±0.15mm unless otherwise noted.( 除特别标注外, 所有尺寸允许公差 ±0.15mm ) SPEC NO:B-13-A-0728 REV NO: A/6 DATE: OCT/31/2015 PAGE: 2 OF 14

3 Selection Guide( 选择指南 ) Part No. 型号 Chip Materials 芯片材料 Lens Type 胶体类型 HL-A-2835D1W-S1-08-HR3 InGaN Yellow Diffused Mass Production list( 批量生产目录 ) Part No. 型号 CCT(K) Min CCT(K) Typ CCT(K) Max Φ(lm) Min Φ(lm) Typ Test Conditions 测试条件 IF=150mA HL-A-2835D1W-S1-08-HR IF=150mA IF=150mA IF=150mA Electrical / Optical Characteristics at Ta=25 C 电性与光学特性 Parameter( 参数 ) Symbol ( 符号 ) Min. ( 最小 ) Typ. ( 平均 ) Max. ( 最大 ) Units ( 单位 ) Test Conditions 测试条件 Forward Voltage 正向电压 Viewing Angle 角度 Color Rendering Index 显色性指数 Reverse Current 反向电流 Thermal Resistance (Junction / Soldering point) 热阻 VF V IF=150mA 2θ1/ deg IF=150mA Ra IF=150mA IR μa VR = 5V Rthj-s /W IF=150mA Note:( 备注 ) 2 1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2 1/2 是半值角, 指光强是光学中心线光强的 1/2 处到光学中心线的角度 2. The above luminous flux measurement allowance tolerance is ±10%. 上述发光通量的测试允许公差为 ±10% 3. The above Color Rendering Index measurement allowance tolerance is ±2 以上显色性指数的测试允许公差为 ±2 4. The above forward voltage measurement allowance tolerance is ±0.1V. 以上所示电压测量误差 ±0.1V 5. The above color coordinates measurement allowance tolerance is ± 以上所示坐标测量误差 ±0.003 SPEC NO:B-13-A-0728 REV NO: A/6 DATE: OCT/31/2015 PAGE: 3 OF 14

4 Absolute Maximum Ratings at Ta=25 C 绝对最大额定值 Parameter( 参数 ) Symbol( 符号 ) Rating( 值 ) Units( 单位 ) Power Dissipation( 功耗 ) Pd 578 mw Forward Current( 正向电流 ) IF 170 ma Peak Forward Current [1]( 峰值正向电流 ) IFP 180 ma Reverse Voltage( 反向电压 ) VR 5 V Electrostatic Discharge (HBM)( 静电 ) ESD 1000 V Operating Temperature( 操作温度 ) Topr -40 ~ +85 Storage Temperature( 保存温度 ) Tstg -40 ~ +100 Junction Temperature 结温 Tj 115 Note:( 备注 ) 1. 1/10 Duty cycle, 0.1ms pulse width.( 脉宽 0.1ms, 周期 1/10) SPEC NO:B-13-A-0728 REV NO: A/6 DATE: OCT/31/2015 PAGE: 4 OF 14

5 Typical optical characteristics curves 典型光学特性曲线 Soldering Temperature vs. Forward Current 焊盘温度与正向电流特性曲线 Forward Current VS. Relative Intensity 正向电流与相对光强特性曲线 1.4 Relative Luminous Intensity Forward Current(mA) Forward Voltage VS. Forward Current 正向电压与正向电流特性曲线 Ambient Temperature VS. Relative Intensity 环境温度与相对光强特性曲线 Forward Current(mA) Forward Voltage (V) SPEC NO:B-13-A-0728 REV NO: A/6 DATE: OCT/31/2015 PAGE: 5 OF 14

6 Typical optical characteristics curves 典型光学特性曲线 Relative spectral emission 相对光谱分布特性曲线 Radiation diagram 辐射图特性曲线 SPEC NO:B-13-A-0728 REV NO: A/6 DATE: OCT/31/2015 PAGE: 6 OF 14

7 Y K 3000K W52 W62 W42 W53 W63 W43 W44 W54 W64 N N K N12 N43 N C K C32 C33 C42 C43 C63 N X SPEC NO:B-13-A-0728 REV NO: A/6 DATE: OCT/31/2015 PAGE: 7 OF 14

8 Bin Range of Chromaticity Coordinate Bin 区分类及色坐标范围 CCT 色温 Bin Code Bin 代码 CIE_x CIE_y Bin Code Bin 代码 CIE_x CIE_y C K C K K C K C K C K N K K C K N K N K N K K N K N K SPEC NO:B-13-A-0728 REV NO: A/6 DATE: OCT/31/2015 PAGE: 8 OF 14

9 Bin Range of Chromaticity Coordinate Bin 区分类及色坐标范围 CCT 色温 Bin Code Bin 代码 CIE_x CIE_y Bin Code Bin 代码 CIE_x CIE_y W K W K W K W K K W K W K W K W K W K SPEC NO:B-13-A-0728 REV NO: A/6 DATE: OCT/31/2015 PAGE: 9 OF 14

10 Reliability Test Items And Conditions 信赖性测试项目及条件 Test Items 项目 Ref. Standard 参考标准 Test Condition 测试条件 Time 时间 Quantity 数量 Ac/Re 接收 / 拒收 Reflow 回流焊 JESD22-B106 Temp:260 max T=10 sec 3 times. 22Pcs. 0/1 Temperature Cycle 温度循环 JESD22-A ±5 30 min. 5 min -40 ±5 30 min. 100 Cycles 22Pcs. 0/1 High Temperature Storage 高温保存 Low Temperature Storage 低温保存 JESD22-A103 Temp:100 ±5 1000Hrs. 22Pcs. 0/1 JESD22-A119 Temp:-40 ±5 1000Hrs. 22Pcs. 0/1 Life Test 常温通电 JESD22-A108 Ta=25 ±5 IF=150mA 1000Hrs. 22Pcs. 0/1 High Temperature High Humidity Life Test 高温高湿通电 JESD22-A ±5 / 85%RH IF=100mA 1000Hrs. 22Pcs. 0/1 Failure Criteria 失效判定标准 Test Items 项目 Symbol 符号 Test Condition 测试条件 Min. 最小 Failure Criteria 判定标准 Max. 最大 Forward Voltage 正向电压 Reverse Current 反向电流 Luminous Flux 光通量 VF IF=150mA - - U.S.L*)x1.1 IR VR = 5V uA Lm IF=150mA L.S.L*)x U.S.L: Upper Specification Limit 规格上限 L.S.L: Lower Specification Limit 规格下限 *The technical information shown in the data sheets is limited to the typical characteristics and circuit examples of the referenced products. It does not constitute the warranting of industrial property nor the granting of any license. 数据工作表中所示的技术信息仅限于典型特征和电路实例引用的产品. 它既不构成工业特性的保证, 也不构成任何许可的授权. SPEC NO:B-13-A-0728 REV NO: A/6 DATE: OCT/31/2015 PAGE: 10 OF 14

11 SMT Reflow Soldering Instructions SMT 回流焊说明 1.Reflow soldering should not be done more than two times. 回流焊不可以做两次以上 2.When soldering, do not put stress on the LEDs during heating 当焊接时, 不要在材料受热时用力压胶体表面 Soldering iron 烙铁焊接 1.When hand soldering, keep the temperature of iron below less 300 less than 3 seconds 当手工焊接时, 烙铁的温度必须小于 300, 时间不可超过 3 秒 2.The hand solder should be done only one times 手工焊接只可焊接一次 Repairing 修补 Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed in advance whether the characteristics of LEDs will or will not be damaged by repairing. LED 回流焊后不应该修复, 当修复是不可避免时, 必须使用双头烙铁 ( 如下图 ), 但必须事先确认此种方式会或不会损坏 LED 本身的特性 Cautions 注意事项 The encapsulated material of the LEDs is silicone. Therefore the LEDs have a soft surface on the top of package. The pressure to the top surface will be influence to the reliability of the LEDs. Precautions should be taken to avoid the strong pressure on the encapsulated part. So when use the picking up nozzle, the pressure on the silicone resin should be proper. LED 封装为硅胶, 故 LED 胶体表面较软, 用力按压胶体表面会影响 LED 可靠性, 因此应有预防措施避免在封装的零件上的强大压力, 当使用吸嘴时, 胶体表面的压力应是恰当的 SPEC NO:B-13-A-0728 REV NO: A/6 DATE: OCT/31/2015 PAGE: 11 OF 14

12 Handling Precautions 处理防备措施 Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more prone to damage by external mechanical force. As a result, Special handling precautions must be observed during assembling using silicone encapsulated LED products, Failure to comply might leads to damage and premature failure of the LED. 相对环氧树脂较脆较硬而言, 硅胶封装较柔软且有弹性, 虽然它的特性大大减少了热应力, 但易受机械外力损坏, 因此在手工处理方面须要对硅胶封装材料做预防措施, 若未按要求操作, 可能会导致 LED 损坏和光衰 1.Handle the component along the side surface by using forceps or appropriate tools; do not directly touch or Handle the silicone lens surface, it may damage the internal circuitry. 通过使用适当的工具从材料侧面夹取, 不可直接用手或尖锐金属压胶体表面, 它可能会损坏内部电路 2.The outer diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. The inner diameter of the nozzle should be as large as possible. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup and avoid damage during production. 为防止气压泄漏,SMD 吸咀外径不可以超过 LED 尺寸, 吸咀内径尺寸应尽可能大, 吸咀顶端材质建议采用柔软材料以防在吸取期间刮伤或损坏 LED 胶体表面, 元件的尺寸必须在取放机里准确的编程好, 以确保精确的吸取和避免生产过程中的损害 3.Do not stack together assembled PCBs containing LEDs. Impact may scratch the silicone lens or damage the internal circuitry 不可将模组材料堆积在一起, 它可能会损坏内部电路 4.Not suitable to operate in acidic environment, PH<7 不可用在 PH<7 的酸性场所 <PH7 SPEC NO:B-13-A-0728 REV NO: A/6 DATE: OCT/31/2015 PAGE: 12 OF 14

13 5.LED operating environment and sulfur element composition cannot be over 100PPM in the LED mating usage material. LED 工作环境及与 LED 适配的材料中硫元素及化合物成份不可超过 100PPM 6.When we need to use external glue for LED application products, please make sure that the external glue matches the LED packaging glue. Additionally,as most of LED packaging glue is silica gel, and it has strong Oxygen permeability as well as strong moisture permeability; in order to prevent external material from getting into the inside of LED, which may cause the malfunction of LED, the single content of Bromine element is required to be less than 900PPM,the single content of Chlorine element is required to be less than 900PPM,the total content of Bromine element and Chlorine element in the external glue of the application products is required to be less than 1500PPM 当我们需要使用外封胶涂抹 LED 产品时, 应确保外封胶与 LED 封装胶水相匹配, 因为大多数 LED 的封装胶水为硅胶, 它有较强的氧化性和较强的吸湿性, 必须防止外封材质进入 LED 内部以造成 LED 的损伤, 单一的溴元素含量要求小于 900PPM, 单一氯元素含量要求小于 900PPM, 在涂抹 LED 产品时要求外封胶溴元素与氯元素总含量必须小于 1500PPM 7.Other points for attention, please refer to our LED user manual. 其它注意事项请参照我们的 LED 使用手册 SPEC NO:B-13-A-0728 REV NO: A/6 DATE: OCT/31/2015 PAGE: 13 OF 14

Label 标签 IV: Luminous intensity rank 亮度等级 VF: Forward voltage rank 电压等级 X/Y: Coordinate rank 色坐标 TC: Color temperature 色温 Tape Specifications (Units : mm) 载带规格 ( 单位 :mm) 0.21 [0.01] 4.00 [0.16] 2.

14 Label 标签 IV: Luminous intensity rank 亮度等级 VF: Forward voltage rank 电压等级 X/Y: Coordinate rank 色坐标 TC: Color temperature 色温 Tape Specifications (Units : mm) 载带规格 ( 单位 :mm) 0.21 [0.01] 4.00 [0.16] 2.00 [0.08] TAPE Polarity Mark Ø1.50 [Ø0.06] 1.75 [0.07] 3.50 [0.14] 8.00 [0.31] TOP TAPA 0.95 [0.04] Reel Dimensions 卷轴尺寸 60.00± ± ± ±0.50 Moisture Resistant Packaging 防潮带包装 Note: The tolerances unless mentioned is ±0.1mm, Unit: mm 注 : 标注公差为 ±0.1mm, 单位 :mm SPEC NO:B-13-A-0728 REV NO: A/6 DATE: OCT/31/2015 PAGE: 14 OF 14

RoHS Specification 规格书 Customer Name: 客户名称 : Customer P/N: 客户品号 : Factory P/N: HL-A-3528H343W-S1-13-HR3 公司品号 : Sending Date: 送样日期 : Client approval Ho

RoHS Specification 规格书 Customer Name: 客户名称 : Customer P/N: 客户品号 : Factory P/N: 公司品号 : Sending Date: 送样日期 : Client approval Hongli approval 客户审核鸿利光电审核 Approval 核准 Audit 确认 Confirmation 制作 Approval 核准 Audit