客户 : CUSTOMER : 产品规格书 PRODUCT 产品名称 : 电源适配器 PRODUCT NAME Power Adaptor 客户产品型号 : CUSTOMER PART No. 供方产品型号 : KELI MODEL. No. 供方产品料号 : SW-6032 KELI PART No. (12V/1A--3C) Rev1.0 客户确认盖章 Customer Signature 规格书 日期 /DATE:2015 年 02 月 04 日 APPROVAL CHECK PREPARE Please return this copy with your company's official stamp on approval of this item, automatic approval to be considered if there is any order coming from your company before formal approval return 厦门市科力电子有限公司 XIAMEN KELI ELECTRONICS CO.,LTD 地址 : 厦门市集美区杏北三路 19 号 ADD:NO.19Factory,Xinglin North3Road, JimeiArea,Xiamen.China. 邮编 /P.C:361022 电话 /TEL:0592-6287052 传真 /FAX:0592-6024482 网页 /Http://www.xmkeli.cn 电子信箱 /E-mail:sales@xmkeli.cn 1
INDEX 目录 INDEX 目录 2 1 Revision 版本. 3 2 General description 概述..4 3 Electronic characteristics 电气特性.4/5 4 Environment Requirements 环境....6 5 Reliability 可靠性. 6 6 Safety requirement 安规要求...7 7 EMC 电磁兼容....7 8 Shape and Dimensions 外形结构图...8 9 DC Cord drawing DC 线.. 9 10 Label 标签.. 10 11 Circuit 原理图 11 12 PCB LAYOUT 线路板图....12 13 材料表 13 14 证书 14-16 2
1 Revision 版本 1.1 Document revision list 文档版本明细 Approval sheet BOM Schematic PCB Label Outline Drawing Date 承认书 Rev1.0 材料原理图线路板标签外形图日期 1.0 1.0 1.0 1.0 1.0 2015/2/4 Note:Initial approval sheet release. Rev1.0 注 : 初始承认书发布为 Rev1.0 1.2 Revision History 修订履历 No. 序号 1 Item Description Issue date RevNo. Applicant 项目 描述 修订日期 版本号 申请 Initial 2015/2/4 1.0 Approval 批准 3
2 General description 概述 This document defines the functional equipment for a 12 watts single output AC to DC power supply. 此文档定义了 12W 单输出的 AC 到 DC 的电源适配器的功能需求 3 Electronic characteristics 电气特性 3.1 Input characteristics 输入特性 Input Voltage Range 输入电压范围 90VAC~264VAC Normal Voltage Range 额定输入电压 100VAC~240VAC Input Frequency Range 输入频率范围 47Hz~63Hz Max.Input Current 满载输入电流 0.5A Max. at full load condition Average Efficiency 平均效率 75% Min. at 220Vac Standby power loss 待机损耗 0.3W Max. 3.2 Output characteristics 输出参数 3.2.1 Output Voltage,Output Current and Regulation 输出电压 电流及输出调整率 Output Voltage Intput Voltage Min. Current Rated Current temperature 输出电压 输入电压 最小电流 额定电流 环境温度 12.0V± 5% AC100-240V 0A 1.0A 25 3.2.2 Ripple & Noise 纹波和噪声 Output Voltage Ripple & Noise +12.0V 120mV MAX(AC220V) Note: Tested by loading side parallel with a 22uF/EC and 0.1uF/Ceramic capacitors and Measured Band-Width with DC-20MHz. 备注 : 测试时在负载侧并联 22uF 的电解电容和 0.1uF 的陶瓷电容, 并将示波器的带宽设定 在 20MHz 3.2.3 Hold-Up Time 维持时间 Output Voltage +12.0V 220Vac Input 5mS 4
KELI PART No. 产品料号 SW-6032 Rev1.0 Note: full load 输出满载 3.2.4 Undershoot and Overshoot 过欠冲 Output Voltage Undershoot and Overshoot +12.0V ±10% 3.2.5 Voltage Rise Time 输出电压上升时间 Output Voltage +12.0V 220Vac Input 50mS Note:The output voltage rise from 10% to 90% 输出电压从 10% 上升到 90% 的时间 3.2.6 Temperature Coefficient 温漂 Output Voltage Temperature Coefficient 3.3 Protection 保护 +12.0V 0.05% / 3.3.1 Short Circuit Protection 短路保护 Output Voltage +12.0V Note Hiccup and auto-recovery 3.3.2 Over Current Protection 过流保护 Output Voltage Over Current Note +12.0V Hiccup and auto-recovery 3.4 Isolation 绝缘性能 3.4.1 Hi-pot test 耐电压测试 3000Vac,5mA,60s between input side to output side. 5
银河电子 输入 --- 输出 3000Vac,5 ma,60s 3.4.2 Insulation 绝缘阻抗 500Vdc,2sec between input side to output side circuit, 100MΩ 输入 --- 输出 500Vdc,2 秒, 100MΩ 4 Environment Requirements 环境 4.1 Temperature. 温度 a Operation 工作温度 :0 --40. b Storage 存储温度 :-10 --70. 4.2 Humidity. 湿度 a Operation 工作湿度 :10--85%.non-condensing b Storage 存储湿度 :5--95%.non-condensing 4.3 Vibration 振动 10-55Hz,0.35mm amplitude,displacement 3 axes,30minutes each axes. 扫描频率 10-55Hz, 位移 0.35mm, 振动三个方向, 每方向 30 分钟 4.4 Cooling Method 冷却方式 Ventilation Cooling 自然风冷 4.5 Drop 跌落 Dropping down the sample freely from 1.0±0.1m height on thick wooden floor 3cm,every of 6 faces one time each side.then retest Isolation and Electrical Specifications, Inspected visually, graze of case is allowed; but no puncture and electric arcing. 样品从高度为 1.0±0.1m, 自由跌落到 3cm 厚的木地板上,6 个表面, 每个方向 1 次 实验后对 外进行检查, 并进行绝缘性能及电性能重新测试, 外观允许有擦伤 ; 但无击穿 飞弧现象 5 Reliability 可靠性 5.1 MTBF 平均无故障时间 50000Hrs power on at 25. 5.2 Burn in 老化 100% Burn-In with 80-100% loading & 25-40 Environment temperature for 4 hours. 全数在带 80-100% 额定负载, 在 25~40 环境温度下老化 4 小时 6
KELI PART No. 产品料号 SW-6032 银河电子 Rev1.0 6 Safety requirement 安规要求 compliance with the following Criterion: 符合以下标准 Safety referring standards CCC GB8898-2011 File Records 2011010807476400 7 EMC 电磁兼容 7.1 EMI (Both of conduction and Radiated) 电磁干扰 Compliance with the following Criterion : Referring standards GB13837-2012/GB17625.1-2012 Specification 7.2 EMS ( 电磁抗扰 ) Compliance with the following Criterion : ITEM Standard ESD 静电测试 *GB/T17626.2-2006/IEC61000-4-2 :2001 EFT 群脉冲测试 *GB/T17626.4-2008/IEC61000-4-4 :2004 DIP 电压跌落 *GB/T17626.11-2008/IEC61000-4-11 :2004 SURGE 浪涌测试 *GB/T17626.5-2008/IEC61000-4-5 :2005 Level 接触放电 :8KV 空气放电 :10KV Level 3 Level 3 L--N=4KV 7
10.5±0.5 1500mm min 74±1.0 KELI PART No. 产品型号 SW-6032 Rev1.0 8 Shape and Dimensions 外形结构图插头为 3C 插头 Unit 单位 : mm Tolerance for no indicate 未标注公差 :±0.5mm 41.0±1.0 29±1.0 2.1±0.1 5.5±0.1 8
注 : Φ5.5±0.1 Φ2.1±0.1 25±1.0 4±0.5 KELI PART No. 产品型号 SW-6032 Rev1.0 9 DC Cord drawing DC 线 Unit 单位 : mm Tolerance for no indicate 未标注公差 :±0.5mm 2.PLUG 头为 : 黑色 + 黑色滚白边. 且黑色滚白边接内芯 ;PLUG 头不可偏 1.DC 线为 AWG 24# 黑色音叉标准平行线. 带凹槽. 芯, 氧化, 粘胶 ; 不可极性相反, 正负极短路. 1500mm min 10.5±0.5 9
29.5±0.3 2.5 10 Label 标签 Unit 单位 : mm Tolerance for no indicate 未标注公差 :±0.5mm R1.0 20.5±0.3 變壓器 型號 : 料號 :SW-6032 輸入 :100-240V~ 50/60Hz 0.5A 輸出 :12.0V 1.0A 2.5 XXXX 廈門市科力電子有限公司製造 1. 标签内容如上图 ; 2. 标签直接激光打印在外壳上 ; 3.XXXX 前两个 XX 为年, 后两个 XX 为周 10
15
16