KillTest 质量更高 服务更好 学习资料 http://www.killtest.cn 半年免费更新服务
Exam : JN0-130 Title : Juniper Juniper Networks Certified Internet Specialist.e(JNCIS-E) Version : Demo 1 / 10
1. Which CLI command is used to set a Privileged Exec password of mypassword? A. enable password 0 mypassword B. enable password 3 mypassword C. enable password 5 mypassword D. enable password 10 mypassword Answer: A 2. You would like to view all Fast Ethernet interfaces currently using VLAN tagging and the specific VLANs each interface is using. Which CLI command displays this information? A. show fast interface B. show vlan interface C. show vlan subinterface D. show fast interface vlan 3. Why would you make a non-backbone area a stub or not-so-stubby area? A. to aggregate routes learned from the ABR B. to lower the cost of routes advertised by the ABR C. to connect a non-contiguous area to the backbone D. to decrease the size of the link-state database in that area 4. Which configuration command places interfaces whose IP addresses are between 192.168.0.0 and 192.168.255.255 into OSPF area 0? A. network 192.168.0.0 255.255.0.0 area 0.0.0.0 B. network 192.168.0.0 0.0.255.255 area 0.0.0.0 C. area 0.0.0.0 network 192.168.0.0 255.255.0.0 D. area 0.0.0.0 network 192.168.0.0 0.0.255.255 Answer: B 2 / 10
5. Is the IS-IS Designated Intermediate System (DIS) election process called Deterministic or Static and why? A. It is Static. If the priorities are equal for a new neighbor and the current DIS only. B. It is Deterministic. If the well-known pseudonode and system ID is configured on the new neighbor only. C. It is Deterministic. When a new router appears on a multi-access network with a higher priority value, it is elected as the DIS. D. It is Static. When a new intermediate system powers up on a multi-access network, even if it has a higher priority, it may become a backup DIS. 6. Which two BGP attributes are incorporated for loop prevention within an AS using a route reflection configuration? (Choose two.) A. AS Path B. Next Hop C. Cluster List D. Originator ID D 7. Which two types of routes may be advertised via EBGP? (Choose two.) A. Routes that do not originate in the local AS and are learned by OSPF. B. Routes that originate on the local router and are advertised into OSPF. C. Routes that are transiting the local router and are BGP learned routes. D. Routes that originate on the local router and are injected using a route map. D 8. In a Bridged 1483 network, which set of commands is used to configure an ATM subinterface? A. interface atm 6/0.33 atm pvc 33 0 33 aal5snap description Company-XYZ 3 / 10
encapsulation bridge1483 ip address unnumbered loopback0 B. interface atm 6/0.33 atm pvc 33 0 33 aal5snap description Company-XYZ encapsulation bridge1483 ip unnumbered loopback0 C. interface atm 6/0.33 atm pvc 33 0 33 aal5snap encapsulation bridge1483 description Company-XYZ ip address unnumbered loopback0 D. interface atm 6/0.33 atm pvc 33 0 33 aal5snap encapsulation bridge1483 description Company-XYZ ip unnumbered loopback0 9. Which three statements are true regarding the DHCP Internal Server? (Choose three.) A. Can be in remote-access mode. B. Can be in equal-access mode. C. Can be in standalone mode. D. Standalone mode is the default. E. Equal-access mode is the default. Answer: BCE 10. Which CLI command displays the status of a PPP over Ethernet subinterface? A. show pppoe interface B. show ppp int state up 4 / 10
C. show ip interface brief D. show pppoe subinterface 11. Which CLI command disconnects all subscribers on an ATM PVC? A. clear port 4/3.99 B. logout port 4/3.99 C. clear subscriber port 4/3.99 D. logout subscriber port 4/3.99 12. Which three statements about Label-Switched Paths (LSPs) are true? (Choose three.) A. LSPs are bidirectional. B. LSPs are unidirectional. C. LSPs can be signaled by CAC. D. LSPs can be configured explicitly. E. LSPs can be configured dynamically. Answer: BDE 13. Which message type is used to initiate an RSVP-TE label switched path? A. path B. resv C. setup D. session Answer: A 14. Which CLI command displays the VRFs that are operational within each virtual router? A. show vir B. show ip vrf C. show vrf vir 5 / 10
D. show mpls vrf Answer: A 15. Which two services protect the ERX Edge Router from unauthorized CLI logins? A. IPSec B. SecureID C. local passwords D. default IP policy E. RADIUS authentication E 16. Your ERX Edge Router is constantly going to a boot## prompt. What is the most likely cause for this condition? A. bad SRP B. low voltage C. bad mid-plane D. corrupted flash 17. Which sequence of events describes the order used to restore normal router operation after experiencing a corrupted flash? A. initialize flash, reload, copy new system files from FTP server B. reload, copy new system files from FTP server, initialize flash C. initialize flash, copy new system files from FTP server, reload D. reload, initialize flash, copy new system files from FTP server 18. You are trying to recover from a corrupted flash. Which configuration command configures an IP address of 192.168.1.1/24 on the SRP management interface when the ERX1400 router is at the boot## prompt? 6 / 10
A. ip address 192.168.1.1/24 B. ip address 192.168.1.1 subnetmask 24 C. ip address 192.168.1.1 255.255.255.0 D. ip address 192.168.1.1 mask 255.255.255.0 19. What describes the functionality of NTP when using multiple virtual routers? A. All virtual routers can act as NTP clients and servers. B. Only one virtual router can act as an NTP client and a server. C. Only one virtual router can act as an NTP server but all can be clients. D. Only one virtual router can act as an NTP client but all can be servers. 20. Which configuration command is used to make the ERX Edge Router an NTP server? A. set ntp-server B. set ntp server C. ntp-server enable D. ntp server enable 21. Which configuration command allows a virtual router to receive updates from a configured NTP source? A. ntp enable B. enable ntp C. set ntp-client D. enable ntp-client Answer: A 22. Which configuration command is used to send debug level events to the console in real time? A. log here severity debug 7 / 10
B. log destination console severity debug C. log severity debug destination console D. log realtime destination console severity debug Answer: B 23. Which command initiates a packet trace for all PPP packets on interface atm 6/1.33? A. log filter debug ppppacket atm 6/1.33 B. log severity debug ppppacket atm 6/1.33 C. log filter debug category ppppacket atm 6/1.33 D. log severity debug category ppppacket atm 6/1.33 Answer: B 24. Log messages are appearing very quickly on the console of your ERX Edge Router. Which Privileged Exec command disables real-time console logging? A. no log here B. no log console C. destination console severity 7 D. destination console logging off Answer: A 25. Which two configuration commands are required to direct debug level console logging to your current ERX Edge Router Telnet session? (Choose two.) A. log here B. log telnet here C. log destination console severity 7 D. log destination telnet severity debug Answer: AC 26. A log filter of log severity DEBUG ppppacket ATM 4/3.66 is configured within the category of ppppacket. 8 / 10
Which configuration command removes this specific log filter? A. no log severity ppppacket B. no log severity debug ppppacket C. no log severity ppppacket atm 4/3.66 D. no log severity debug ppppacket 4/3.66 27. Which configuration command removes all log filters currently configured on the ERX Edge Router? A. no log here B. no log fields C. no log filters D. no log severity 28. Which three statements describe macros on the ERX Edge Router? (Choose three.) A. They prompt users for input. B. They cannot prompt users for input. C. They can be created on the router itself. D. They are an embedded programming language. E. They can be created on the user's workstation. Answer: ADE 29. Which command is used to execute a macro called setup.mac? A. macro setup B. macro setup.mac C. run macro setup D. run macro setup.mac Answer: B 30. Which control expression must be the last line in all macros? 9 / 10
A. <# end #> B. <# finish #> C. <# endtmpl #> D. <# terminate #> 10 / 10