844 IEEE MICROWAVE AND WIRELESS COMPONENTS LETTERS, VOL. 17, NO. 12, DECEMBER 2007 Fig. 1. Proposed broadband SIW planar balun. Fig. 2. Electrical fie

Size: px

Start display at page:

Download "844 IEEE MICROWAVE AND WIRELESS COMPONENTS LETTERS, VOL. 17, NO. 12, DECEMBER 2007 Fig. 1. Proposed broadband SIW planar balun. Fig. 2. Electrical fie"

读孟
5 years ago
Views:

1 IEEE MICROWAVE AND WIRELESS COMPONENTS LETTERS, VOL. 17, NO. 12, DECEMBER A Broadband Substrate Integrated Waveguide (SIW) Planar Balun Zhen-Yu Zhang and Ke Wu, Fellow, IEEE Abstract A broadband planar balun is presented in this work that makes use of a substrate integrated waveguide (SIW) technique using a printed circuit board process. The proposed balun structure is able to operate at millimeter wave frequencies and it does not require any tight line coupling sections as frequently used in monolithic microwave integrated circuit balun design. In addition, this balun can be integrated with other planar topologies including nonplanar circuits made of the same substrate for achieving high efficiency. This balun structure consists of a 3 db SIW power divider and microstrip lines that are placed on both sides of the substrate at balanced ports to obtain an 180 phase shift. The concept is validated by simulations and measurements. Our measured results suggest that a 10 db return loss at unbalanced port can easily be achieved across a 42% bandwidth from 19 to 29 GHz. Measured amplitude and phase imbalance between two balanced ports are within 1 db and 5, respectively. Index Terms Broadband structure, millimeter wave techniques, planar balun, substrate integrated waveguide (SIW). I. INTRODUCTION ABALUN is a device or circuit that converts signals between an unbalanced circuit structure and a balanced counterpart. A large number of analog radio frequency (RF) and microwave circuits require balanced inputs and outputs in order to reduce noise and high order harmonics as well as improve dynamic range of circuits. With the inherent features of generating balanced signals, baluns are widely used in many wireless communication systems for realizing critical building blocks such as balanced mixer, push pull amplifier and antenna feed networks. Although various types of baluns have been reported for applications in connection with microstrip circuits in the form of microwave integrated circuits (MICs) and monolithic microwave integrated circuits (MMICs), a planar balun structure with favourable performance has been a challenging research topic over the past several decades [1] [4]. Among them, the 180 hybrids and multisection half-wave baluns are frequently used in microwave circuits as they can easily be realized in many design procedures and fabrication processes, Manuscript received April 15, 2007; revised August 20, This work was supported in part by the National Sciences and Engineering Research Council of Canada. The authors are with the Poly-Grames Research Center, Département de Génie Électrique, Ecole Polytechnique de Montreal, Montreal, QC H3T 1J4 Canada ( zhang.zhenyu@polymtl.ca; ke.wu@polymtl.ca). Color versions of one or more of the figures in this paper are available online at Digital Object Identifier /LMWC and also they provide satisfactory performances, namely, low voltage standing wave ratio (VSWR), small insertion loss and good amplitude/phase imbalance between balanced ports. However, they fail to maintain those advantageous features over a wide frequency range. Furthermore, they are hardly employable when the operating frequency goes into millimeter-wave frequency band. The Marchand balun is a known broadband solution but its performances largely depend on a tight coupling of the coupled line sections. In addition, it is difficult to design with the conventional printed circuit board (PCB) process at frequencies beyond 20 GHz. Due to those challenging issues in the design of planar baluns, non-planar baluns are usually used instead [5], [6]. However, the use of a non-planar topology may prevent itself from its seamless integration with planar circuits, especially with respect to surface mounted chip structures. In this letter, a broadband substrate integrated waveguide (SIW) balun is proposed and presented, which is made in planar form. The SIW concept has been proposed and demonstrated in many previous publications [7], [8]. The fundamental point is that the usually non-planar hollow rectangular waveguide can effectively be synthesized in planar substrate with metallized slots or trenches or even arrays of metallic via posts. The proposed broadband SIW-based planar balun consists of a 3 db SIW power divider [7] for equal power splitting and microstrip lines which are placed on different sides of a dielectric substrate at balanced ports to obtain a 180 phase shift. Since the SIW power divider presents broadband characteristics, the newly proposed balun structure can provide a broadband frequency response, which is a critical feature for many wireless communication systems. On the other hand, the planarity of balanced ports can further be achieved by using a metallic via hole to conduct one of the differential signals from one side to the other. As such, the new balun can easily be designed and fabricated on a double-sided PCB substrate. Compared to previously reported structures, the proposed balun can easily be used at millimeter wave frequencies and also the structure does not require tight coupling sections as usually made in many MMIC balun structures. Of course, the proposed topology can be integrated with other planar structures including nonplanar circuits within the same substrate for achieving high efficiency at low cost. To demonstrate the design methodology and structural features, a prototype of the balun is presented in this work. The design was made through the use of a commercial software package (Ansoft HFSS v 10.1 [9]) and validated by experiments /$ IEEE

844 IEEE MICROWAVE AND WIRELESS COMPONENTS LETTERS, VOL. 17, NO. 12, DECEMBER 2007 Fig. 1. Proposed broadband SIW planar balun. Fig. 2. Electrical field plots on the A plane. II.

Therefore, the monomode bandwidth is guaranteed with mode related to mode.

2 844 IEEE MICROWAVE AND WIRELESS COMPONENTS LETTERS, VOL. 17, NO. 12, DECEMBER 2007 Fig. 1. Proposed broadband SIW planar balun. Fig. 2. Electrical field plots on the A plane. II. GEOMETRY AND DESIGN OF BROADBAND SIW PLANAR BALUN STRUCTURE The SIW structure is known to have broadband monomode characteristics compared to its conventional waveguide counterpart as the SIW usually supports only modes. This is because the synthesis of bilateral metallic walls is made with discontinued metallized via or slot arrays in the thin dielectric substrate, which does not allow the guidance of the TM modes. Therefore, the monomode bandwidth is guaranteed with mode related to mode. In addition, the SIW yields better loss characteristics compared with other schemes like microstrip and coplanar waveguide (CPW) lines. It can be used at millimeter wave frequencies where loss becomes critical. Fig. 1 shows the structure of the proposed broadband SIW planar balun, in which the SIW section is realized by using metallic slot arrays. The dark area stands for the metallization parts on the bottom plane of the double-sided PCB substrate and the gray area stands for the metallization on the top plane. The proposed balun consists of a 3 db SIW power divider for equal power splitting and microstrip line sections which are placed on different sides of the PCB substrate at balanced ports so as to obtain an 180 phase shift. To further demonstrate this idea with a better explanation, an intersection plane A is chosen, which is marked in Fig. 1. Fig. 2 illustrates the electrical fields on plane A, from which it can be found that the E-field orientations of balanced ports are different from each other, which means an 180 phase difference. The transition between the SIW and microstrip line is referred to a well-described tapered line structure given in [10]. The only difference is that the ground plane of the transitions is also modified in the form of tapered section so that the transitions can provide a better performance. The planarity of balanced ports is further achieved using a metallic via hole transition to conduct one of the differential signals from one side to the other. As shown in Fig. 3, the via-hole transition and the tapered ground plane were carefully designed to ensure that the RF signal can Fig. 3. Physical dimensions of the experimental prototype of the proposed SIW planar balun (w = 1.74 mm, w = 0.6 mm, w = 2.14 mm, w = 5.2 mm, w = 5.2 mm, l = 12 mm, l = 3 mm, l = 7 mm, l = 5.6 mm, l = 4.25 mm, s = 0.3 mm, s = 0.6 mm, s = 0.15 mm, x = 1.8 mm, x = 1.6 mm, y = 0.4 mm, r = 1.6 mm, r = 0.75 mm, = 0.6 mm and = 0.25 mm). be smoothly transferred to the output port with very low insertion loss and little discontinuity. All the interconnections that generate the discontinuities were made into tapered shape so that the discontinuity and inductance effects were minimized. The optimization was done with the aid of Ansoft HFSS v The general design considerations of the tapered lines can be referred to the previous publication [6]. To demonstrate the design methodology and electrical performances, an experimental prototype of the proposed balun is designed and fabricated at 24 GHz. The substrate used in our work is RO6002 with a thickness of 10 mil and a dielectric constant Fig. 3 shows the physical dimensions of the designed broadband SIW planar balun. The via hole transition part is enlarged to provide a clear illustration. The gray area in this case stands for the metallization on the top plane of the substrate while the dashed-line area stands for the metallization on the bottom plane of the substrate. The SIW is realized by using metallic slots. The balanced ports are extended to different directions just for the measurement consideration. III. SIMULATION AND MEASUREMENT RESULTS Fig. 4(a) (b) display the simulated and measured results for the amplitude response and phase balance of the proposed planar balun, in which the solid line stands for the simulated results and the dashed line stands for the measured results. This balun is simulated by using Ansoft HFSS v The measurements are carried out by using an Aristu test fixture model 3680 K with the maximum frequency up to 40 GHz and an HP 8510C vector network analyzer. The calibration work is

3 ZHANG AND WU: BROADBAND SIW PLANAR BALUN 845 IV. CONCLUSION A broadband SIW planar balun implemented on a PCB is proposed and presented in this letter. The balun structure consists of a 3 db SIW power divider for equal power splitting and microstrip lines which are placed on different sides of the PCB substrate at balanced ports to obtain an 180 phase shift. To demonstrate the design concept, an experimental prototype is fabricated. The balun structure is simulated and validated by the measurement. The merits of this balun are concluded by the fact that it can easily operate at millimeter wave frequencies and does not require any tight coupling sections as usually used in many MMIC balun structures. In addition, the balun can be integrated with other planar circuits including nonplanar and multilayered structures for achieving high circuit efficiency. It can be anticipated that the proposed balun will have a broad range of RF and millimeter-wave applications. REFERENCES Fig. 4. S-parameters of the proposed balun: (a) amplitude responses and (b) phase responses. done by using a set of TRL calibration standards. It is observed that a good agreement is achieved between the measurement and the simulation. Measured results show that better than 10 db return loss of the unbalanced port is well achieved across the whole bandwidth of interest from around 19 to 29 GHz, or 42% of bandwidth. Within the bandwidth of operation, the measured amplitude and phase imbalance between the two balanced ports are respectively within 1 db and 5, except that the phase imbalance reaches 8 at around 28 GHz. [1] N. Marchand, Transmission-line conversion transformers, Electronics, vol. 17, no. 12, pp , Dec [2] R. Sturdivant, Balun designs for wireless mixers, amplifiers and antennas, Appl. Microw., pp , [3] M. Basraoui and S. N. Prasad, Wideband, planar, log-periodic balun, in IEEE MTT-S Int. Dig., 1998, pp [4] Z. Y. Zhang, Y. X. Guo, L. C. Ong, and M. Y. W. Chia, Improved planar marchand balun with a patterned ground plane, Int. J. RF Microw. CAE, vol. 15, no. 3, pp , May [5] S. A. Maas, Microwave Mixer, 2nd ed. Norwood, MA: Artech House,, 1993, pp [6] J. W. Duncan and V. P. Minerva, 100:1 Bandwidth balun transformer, IRE Proc., vol. 48, pp , [7] S. Germain, D. Deslandes, and K. Wu, Development of substrate integrated waveguide power dividers, in Proc. IEEE Canadian Conf. Elect. Comput. Eng., 2003, pp [8] D. Deslandes and K. Wu, Single-substrate integration technique of planar circuits and waveguide components, IEEE Trans. Microw. Theory Tech., vol. 51, no. 2, pp , Feb [9] Ansoft Corporation: Ansoft HFSS, Version [10] D. Deslandes and K. Wu, Integrated microstrip and rectangular waveguide in planar form, IEEE Microw. Wireless Compon. Lett., vol. 11, no. 2, pp , Feb

易迪拓培训专注于微波射频天线设计人才的培养网址 :http://www.edatop.com 射频和天线设计培训课程推荐易迪拓培训 (www.edatop.com) 由数名来自于研发第一线的资深工程师发起成立, 致力并专注于微波射频天线设计研发人才的培养 ; 我们于 2006 年整合合并微波 EDA 网 (www.mweda.

永业科技全一电子等多家台湾地区企业易迪拓培训课程列表 :http://www.edatop.com/peixun/rfe/129.

4 易迪拓培训专注于微波射频天线设计人才的培养网址 : 射频和天线设计培训课程推荐易迪拓培训 ( 由数名来自于研发第一线的资深工程师发起成立, 致力并专注于微波射频天线设计研发人才的培养 ; 我们于 2006 年整合合并微波 EDA 网 ( 现已发展成为国内最大的微波射频和天线设计人才培养基地, 成功推出多套微波射频以及天线设计经典培训课程和 ADS HFSS 等专业软件使用培训课程, 广受客户好评 ; 并先后与人民邮电出版社电子工业出版社合作出版了多本专业图书, 帮助数万名工程师提升了专业技术能力客户遍布中兴通讯研通高频埃威航电国人通信等多家国内知名公司, 以及台湾工业技术研究院永业科技全一电子等多家台湾地区企业易迪拓培训课程列表 : 射频工程师养成培训课程套装该套装精选了射频专业基础培训课程射频仿真设计培训课程和射频电路测量培训课程三个类别共 30 门视频培训课程和 3 本图书教材 ; 旨在引领学员全面学习一个射频工程师需要熟悉理解和掌握的专业知识和研发设计能力通过套装的学习, 能够让学员完全达到和胜任一个合格的射频工程师的要求课程网址 : ADS 学习培训课程套装该套装是迄今国内最全面最权威的 ADS 培训教程, 共包含 10 门 ADS 学习培训课程课程是由具有多年 ADS 使用经验的微波射频与通信系统设计领域资深专家讲解, 并多结合设计实例, 由浅入深详细而又全面地讲解了 ADS 在微波射频电路设计通信系统设计和电磁仿真设计方面的内容能让您在最短的时间内学会使用 ADS, 迅速提升个人技术能力, 把 ADS 真正应用到实际研发工作中去, 成为 ADS 设计专家... 课程网址 : HFSS 学习培训课程套装该套课程套装包含了本站全部 HFSS 培训课程, 是迄今国内最全面最专业的 HFSS 培训教程套装, 可以帮助您从零开始, 全面深入学习 HFSS 的各项功能和在多个方面的工程应用购买套装, 更可超值赠送 3 个月免费学习答疑, 随时解答您学习过程中遇到的棘手问题, 让您的 HFSS 学习更加轻松顺畅课程网址 : `

易迪拓培训专注于微波射频天线设计人才的培养网址 :http://www.edatop.

5 易迪拓培训专注于微波射频天线设计人才的培养网址 : CST 学习培训课程套装该培训套装由易迪拓培训联合微波 EDA 网共同推出, 是最全面系统专业的 CST 微波工作室培训课程套装, 所有课程都由经验丰富的专家授课, 视频教学, 可以帮助您从零开始, 全面系统地学习 CST 微波工作的各项功能及其在微波射频天线设计等领域的设计应用且购买该套装, 还可超值赠送 3 个月免费学习答疑课程网址 : HFSS 天线设计培训课程套装套装包含 6 门视频课程和 1 本图书, 课程从基础讲起, 内容由浅入深, 理论介绍和实际操作讲解相结合, 全面系统的讲解了 HFSS 天线设计的全过程是国内最全面最专业的 HFSS 天线设计课程, 可以帮助您快速学习掌握如何使用 HFSS 设计天线, 让天线设计不再难课程网址 : MHz NFC/RFID 线圈天线设计培训课程套装套装包含 4 门视频培训课程, 培训将 13.56MHz 线圈天线设计原理和仿真设计实践相结合, 全面系统地讲解了 13.56MHz 线圈天线的工作原理设计方法设计考量以及使用 HFSS 和 CST 仿真分析线圈天线的具体操作, 同时还介绍了 13.56MHz 线圈天线匹配电路的设计和调试通过该套课程的学习, 可以帮助您快速学习掌握 13.56MHz 线圈天线及其匹配电路的原理设计和调试详情浏览 : 我们的课程优势 : 成立于 2004 年,10 多年丰富的行业经验, 一直致力并专注于微波射频和天线设计工程师的培养, 更了解该行业对人才的要求经验丰富的一线资深工程师讲授, 结合实际工程案例, 直观实用易学联系我们 : 易迪拓培训官网 : 微波 EDA 网 : 官方淘宝店 : 专注于微波射频天线设计人才的培养易迪拓培训官方网址 : 淘宝网店 :

ANSYS 在航空航天器电磁兼容、电磁干扰分析中的应

ANSYS 在航空航天器电磁兼容、电磁干扰分析中的应易迪拓培训专注于微波射频天线设计人才的培养网址 :http://www.edatop.com 射频和天线设计培训课程推荐易迪拓培训 (www.edatop.com) 由数名来自于研发第一线的资深工程师发起成立, 致力并专注于微波射频天线设计研发人才的培养 ; 我们于 2006 年整合合并微波 EDA 网 (www.mweda.com), 现已发展成为国内最大的微波射频和天线设计人才培养基地,