Practical RF Printed Circuit Board Design

Size: px

Start display at page:

Download "Practical RF Printed Circuit Board Design"

若横郎
5 years ago
Views:

1 PRACTICAL RF PRINTED CIRCUIT BOARD DESIGN Geoff Smithson. Overview The electrical characteristics of the printed circuit board (PCB) used to physically mount and connect the circuit components in a high frequency product will have a significant impact on the performance of that product. The potential magnitude of the effect of the PCB design increases with frequency as the parasitic elements tend to a similar magnitude to the typical lumped components used. This leads to the requirement for increased inclusion of electrical models representing PCB structures into the circuit simulation. In practical radio products the requirements on the PCB design can sometimes be in conflict with best manufacturing practise. In order to achieve the most optimum solution in all respects the radio designer, the PCB designer and the manufacturing engineer must all have some appreciation of each others requirements. PCB Materials A variety of different materials are used to fabricate PCBs. These materials can also be assembled in a variety of different ways potentially using multiple laminates, different materials and different plated through via structures. A range of finishes can be used making use of materials such as Gold, Nickel, Tin and Lead. Typical board materials used for radio circuits are FR4, Rogers R04003 and Rogers RT/Duroid. All of these come in a variety of grades and forms and have different electrical characteristics and cost. Hybrid structures combining two of these materials are possible, allowing a combination of properties to be used for different circuit areas. Some examples of hybrid structures that have been used in commercial products include a duroid and FR4 construction used for microwave satellite receiver low noise down converter blocks produced by various companies in the 1990s as well as a Rodgers and FR4 hybrid construction used by Plextek in a formula one telemetry system. (A photograph of the Rodgers R04003 and FR4 hybrid is shown at the end of this paper). A summary of the main electrical characteristics of three commonly used board materials for radio products are given in the table below. The cost increases with increased dielectric tolerance and reduced loss. Board Material: Typical Dielectric constant Dielectric constant tolerance Loss tangent FR4 4 +/-5% +/-25% 0.01 Rogers R / Rogers RT/Duroid 2.2 +/ Table 1. Summary of the principle properties of different radio PCB materials. Geoff Smithson is an RF Engineer with Plextek Ltd, London Road, Great Chesterford, Essex. Tel: +44 (0) Fax: +44 (0) gs@plextek.co.uk

2 PCB Fabrication Process The most common processes used in the fabrication of PCBs are drilling, plating, bonding and etching. Some new developments are underway where lasers are utilised to distinguish conducts. The principle advantage of this development being the ability to use smaller dimensioned features including track widths down to 0.05 mm. In all but the lowest cost radio products multilayer PCBs are used. These comprise of a number of laminates of board material individually etched and bonded. The principle advantages of this being the ability to use more than two conductor layers reducing the required board space. The disadvantage being increased cost. A typical PCB structure used in volume radio products, such as GSM mobiles, is a four layer or six layer FR4 multilayer construction. In addition to different structures for the laminates, a variety of different structures can be used for the plated through holes (known as via holes). The most basic structure being simply to have all holes going through all layers of the board. For a multilayer board these can then be used to link tracks on any layer to any other or all other layers. The advantage of this structure being the reduced processing time as the vias are all drilled in one process. The disadvantage being that all vias take up space on all layers. More complex structures are possible using blind or buried vias. The term blind via refers to a via between a number of layers including, an outer layer, but not through all layers. The term buried via refers to a via between a number of layers, not including an outer layer and not through all layers. The type of via structure used will have a mayor effect on the processes required to fabricate the PCB and consequently the cost of the finished board. Examples of these three different via types are shown in the PCB cross-section below. Blind via Through hole via Buried via Fig 1. PCB cross-section showing different plated through hole types. PCB Fabrication Limitations In order to design a product using a PCB it is important to understand the practical limitations of the fabrication process. The manufacturing processes used to etch the tracks, drill the holes and assemble the laminates have limitations. Exceeding these limitations will significantly increase the cost of the PCB as manufacturing yields reduce. The typical minimum limit on track thickness for a high volume, complex product is around 0.2 mm. A similar minimum limit applies to the minimum gap between two different conducts. (The larger the minimum track and gap width used, the lower the cost of the PCB). Some PCB manufacturers offer etched track widths down to mm. These do however come at a premium and should only be specified if absolutely necessary and after detailed

3 discussions with the chosen vendor. The typical tolerance on the width of etched tracks is +/ mm. The minimum via hole size used will have a significant effect on the cost of the board as it limits the number of PCBs that can be drilled as a stack. Not withstanding the radio performance implications of small diameter via holes, typical minimum sizes of 0.25 mm are commonly used. A reduced cost will be achieved if the minimum hole diameter of 0.5 mm can be used. A summary of typical process limitations is given in the table below for FR4 PCBs. Three arbitrary cost brackets have been chosen to highlight the range of tolerances. Actual available tolerances and the cost implications of different processes will vary with PCB vendor. Minimum track and gap Copper etch tolerance Smallest hole diameter Low cost radio product PCB. Medium cost radio product PCB. High cost radio product PCB mm 0.2 mm mm +/ mm +/ mm +/ mm 0.7 mm 0.5 mm 0.2 mm Number of layers Via structure Through hole Through hole and blind Through hole, blind and buried Board finish Hot air solder levelled Gold flash Gold plated Table 2. Summary of typical PCB process limitation for a range of cost options. PCB Parasitic Elements The term PCB parasitic is used to refer to a physical attribute of the PCB that has an impact on the performance of the circuit. For example in a high frequency radio circuit it is simple to see how a long thin track will be inductive and a large pad over a ground plan will be capacitive. Consider, for instance, a surface mount 0805 size capacitor on a 0.25 mm thick double sided FR4 PCB above a ground plane. The equivalent high frequency circuit for the whole of the above structure can be described by the following circuit. Fig 2. Equivalent circuit for an SMT capacitor mounted on an FR4 PCB with ground plane.

4 As can be seen in the diagram above, the simple capacitor now has a significant number of other elements attached to it in order to model both the device imperfections and effects of the PCB. These include shunt capacitors to model the pad capacitance and two series inductors to model the device pad metalisation and PCB track inductance. In addition to the parasitic elements described above, used to model the series capacitor, the impedance of the connections between circuit components and the ground plane must also be modelled in real circuits. A plated through via hole will have a significant inductance and good circuit simulation packages will include models to allow there addition. The typical inductance of a 1.6 mm long, 0.2 mm diameter via hole can be as much as 0.75 nh. This may seem very small, but as can be seen in the circuit example below, it can be significant. Component Parasitic Elements In a similar way to the PCB, components also have non ideal characteristics. While the use of surface mount devices helps to reduce the effect of this on radio circuit performance (principally due to the small construction and reduced lead length) it is significant. The term component Q or Quality factor is used as a figure of merit for a reactive device. The Q value is the ratio of the energy stored by the device to energy dissipated. Typical values for a wire-wound inductor would be of the order of 50 and for a ceramic COG dielectric capacitor of the order of 200 (the Q of a component is frequency dependent). Ground Planes A number of different ground plane strategies can be adopted for a radio product PCB. There is no unique answer to the best strategy for a given type of product. Some people are great advocates of split ground planes for analogue, digital, radio or audio circuits. Experience on a number of radio products at Plextek has shown that a single low impedance ground plane for all parts of the circuit is usually a good starting point. Often attempts to split the ground planes causes more problems than it solves. Careful consideration of the flow of currents throughout the product is essential to minimise digital interference with audio and radio circuits. Given the proliferation in the use of DSP and microprocessors in radio products this is a very significant issue. Circuit Example The potential significance of the parasitic PCB and component elements detailed above can be demonstrated with an example. Consider a radio designer who is charged with designing a low pass filter for use on the output of a power amplifier, used in the output stage of a transmitter, to reduce the out of band harmonic emissions. Requirement: Transmitter output power: +30 dbm Third harmonic level (max) at Tx output: -40 dbc Fifth harmonic level (max) at Tx output: -50 dbc Required max out of band emissions: -30 dbm Carrier frequency: 1 GHz Termination impedance: 50 Ω Therefore, at least 20 db of attenuation is required at the third harmonic frequency (3 GHz) and at least 10 db at the fifth harmonic frequency (5 GHz). Examination of standard curves shows that a 5 th order Butterworth will give significantly greater attenuation than required (> 30 3 rd harmonic and > 50 5 th harmonic).

5 The circuit shown below is a 5 th order Butterworth filter. The simulated ideal parasitic free performance for this filter is also shown. Fig 3. Ideal lumped 5 th order Butterworth low pass filter with simulated response. The revised circuit for the same 5 th order Butterworth filter, including PCB and component parasitic elements is shown below along with the revised simulated performance. It can clearly be seen that the actual performance will be very different from the ideal case. Fig 4. Real lumped 5 th order Butterworth low pass filter including PCB and component parasitics. As can be seen from the two graphs, the 3 rd harmonic rejection has improved by nearly 20 db and the 5 th harmonic rejection has been reduced by over 50 db. Additionally the pass band loss has increased from 0.25 db to 4.5 db. Summary This paper has considered the attributes of the three base PCB materials commonly used for radio circuits. In addition to a choice of materials, the PCB designer also has the option to assembly the board from a number of potentially different material laminates of potentially different thickness. This can be very helpful in allowing a single board to accommodate dissimilar circuitry, for example baseband and radio or high frequency radio and analogue. As with the choice of plated through hole structure used, the designer must carefully consider the cost implications of hybrid and multilayer constructions. PCB fabrication process limitations and PCB parasitic effects are discussed. For an optimum commercial radio product it is important for the PCB layout engineer and the circuit design engineer each understand both of these issues. Finally an example is presented to show the significant effect of lumped component and PCB parasitics on the performance of a radio circuit.

6 Two examples of commercial RF products designed by Plextek are shown below. Photo 1. Formula 1 telemetry system using a hybrid Rogers R04003 / FR4 PCB. Photo 2. A six layer PCB with through and blind vias used in a GSM phone.

易迪拓培训专注于微波射频天线设计人才的培养网址 :http://www.edatop.com 射频和天线设计培训课程推荐易迪拓培训 (www.edatop.com) 由数名来自于研发第一线的资深工程师发起成立, 致力并专注于微波射频天线设计研发人才的培养 ; 我们于 2006 年整合合并微波 EDA 网 (www.mweda.

永业科技全一电子等多家台湾地区企业易迪拓培训课程列表 :http://www.edatop.com/peixun/rfe/129.

7 易迪拓培训专注于微波射频天线设计人才的培养网址 : 射频和天线设计培训课程推荐易迪拓培训 ( 由数名来自于研发第一线的资深工程师发起成立, 致力并专注于微波射频天线设计研发人才的培养 ; 我们于 2006 年整合合并微波 EDA 网 ( 现已发展成为国内最大的微波射频和天线设计人才培养基地, 成功推出多套微波射频以及天线设计经典培训课程和 ADS HFSS 等专业软件使用培训课程, 广受客户好评 ; 并先后与人民邮电出版社电子工业出版社合作出版了多本专业图书, 帮助数万名工程师提升了专业技术能力客户遍布中兴通讯研通高频埃威航电国人通信等多家国内知名公司, 以及台湾工业技术研究院永业科技全一电子等多家台湾地区企业易迪拓培训课程列表 : 射频工程师养成培训课程套装该套装精选了射频专业基础培训课程射频仿真设计培训课程和射频电路测量培训课程三个类别共 30 门视频培训课程和 3 本图书教材 ; 旨在引领学员全面学习一个射频工程师需要熟悉理解和掌握的专业知识和研发设计能力通过套装的学习, 能够让学员完全达到和胜任一个合格的射频工程师的要求课程网址 : ADS 学习培训课程套装该套装是迄今国内最全面最权威的 ADS 培训教程, 共包含 10 门 ADS 学习培训课程课程是由具有多年 ADS 使用经验的微波射频与通信系统设计领域资深专家讲解, 并多结合设计实例, 由浅入深详细而又全面地讲解了 ADS 在微波射频电路设计通信系统设计和电磁仿真设计方面的内容能让您在最短的时间内学会使用 ADS, 迅速提升个人技术能力, 把 ADS 真正应用到实际研发工作中去, 成为 ADS 设计专家... 课程网址 : HFSS 学习培训课程套装该套课程套装包含了本站全部 HFSS 培训课程, 是迄今国内最全面最专业的 HFSS 培训教程套装, 可以帮助您从零开始, 全面深入学习 HFSS 的各项功能和在多个方面的工程应用购买套装, 更可超值赠送 3 个月免费学习答疑, 随时解答您学习过程中遇到的棘手问题, 让您的 HFSS 学习更加轻松顺畅课程网址 : `

易迪拓培训专注于微波射频天线设计人才的培养网址 :http://www.edatop.

8 易迪拓培训专注于微波射频天线设计人才的培养网址 : CST 学习培训课程套装该培训套装由易迪拓培训联合微波 EDA 网共同推出, 是最全面系统专业的 CST 微波工作室培训课程套装, 所有课程都由经验丰富的专家授课, 视频教学, 可以帮助您从零开始, 全面系统地学习 CST 微波工作的各项功能及其在微波射频天线设计等领域的设计应用且购买该套装, 还可超值赠送 3 个月免费学习答疑课程网址 : HFSS 天线设计培训课程套装套装包含 6 门视频课程和 1 本图书, 课程从基础讲起, 内容由浅入深, 理论介绍和实际操作讲解相结合, 全面系统的讲解了 HFSS 天线设计的全过程是国内最全面最专业的 HFSS 天线设计课程, 可以帮助您快速学习掌握如何使用 HFSS 设计天线, 让天线设计不再难课程网址 : MHz NFC/RFID 线圈天线设计培训课程套装套装包含 4 门视频培训课程, 培训将 13.56MHz 线圈天线设计原理和仿真设计实践相结合, 全面系统地讲解了 13.56MHz 线圈天线的工作原理设计方法设计考量以及使用 HFSS 和 CST 仿真分析线圈天线的具体操作, 同时还介绍了 13.56MHz 线圈天线匹配电路的设计和调试通过该套课程的学习, 可以帮助您快速学习掌握 13.56MHz 线圈天线及其匹配电路的原理设计和调试详情浏览 : 我们的课程优势 : 成立于 2004 年,10 多年丰富的行业经验, 一直致力并专注于微波射频和天线设计工程师的培养, 更了解该行业对人才的要求经验丰富的一线资深工程师讲授, 结合实际工程案例, 直观实用易学联系我们 : 易迪拓培训官网 : 微波 EDA 网 : 官方淘宝店 : 专注于微波射频天线设计人才的培养易迪拓培训官方网址 : 淘宝网店 :

ANSYS 在航空航天器电磁兼容、电磁干扰分析中的应

ANSYS 在航空航天器电磁兼容、电磁干扰分析中的应易迪拓培训专注于微波射频天线设计人才的培养网址 :http://www.edatop.com 射频和天线设计培训课程推荐易迪拓培训 (www.edatop.com) 由数名来自于研发第一线的资深工程师发起成立, 致力并专注于微波射频天线设计研发人才的培养 ; 我们于 2006 年整合合并微波 EDA 网 (www.mweda.com), 现已发展成为国内最大的微波射频和天线设计人才培养基地,