Instruction Manual

Size: px

Start display at page:

Download "Instruction Manual"

掌贲
5 years ago
Views:

1 PT-1136 CORDLESS LIGHTED SCREWDRIVER 3.6V User s Manual 1 st Edition, Copy Right by Prokit s Industrial Co., Ltd.

2 Please read this instruction manual carefully before using the tool General Safety Rules WARNING Read all safety warnings and all instructions Failure to follow all warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference The term power tool in the warnings refer to your mains operated (corded) power tool or battery operated (cordless) power tool. 1. Work area a) Keep work area clean and well lit. Cluttered and dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2. Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tools in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. 3. Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. 1

3 f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dust related hazards. 4. Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not(use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control; g) Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from intended could result in a hazardous situation. 5. Battery tool use and care a) Recharge only with the adaptor specified by the manufacturer. A charter that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. b) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. c) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected form the battery may cause irritation or burns. d) For ensure the maximum life out of a new battery, always charge the battery before use. e) Always discharge battery completely when long time no use or not often to use power tool before use f) Battery will auto discharge when long time no use,.please charge the battery 50 days per time g) Please keep ambience dry and opportune temperature where storage power tool. It will quicken auto discharge where environment too high or too low temperature. Hi-humidity will damage the battery and will make power tool rust 2

4 6. Service Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Safety Advice for Rechargeable Battery Use only the battery provided with the replacement rechargeable battery from Pro skit and the provided adaptor. Protect battery and adaptor from humidity. Do not operate the adaptor outdoors. When it is not in use and before cleaning and servicing, disconnect the adaptor from the power supply. Do not open or attempt to repair the battery or the adaptor. If any parts are defective, have them repaired by a qualified technician or send them to our service department for repair. Only charge the battery at an ambient (surrounding air) temperature between 10ºC and 40ºC. A charged battery can be used to power the machine under ambient temperature conditions between 0ºC and 50ºC.When not in use, store the battery in a dry place between 10ºC and 30ºC. Important! Danger! Never short-circuit the battery or expose it to moisture. Do not store it together with any metal parts which could short-circuit the contacts. The battery could overheat, start burning or explode. If any person comes into contact with acid or similar internal fluids or substances contained in the battery, wash off these substances immediately with plenty of water. If these substances make contact with the eyes, rinse with plenty of water and visit a doctor immediately. Do not place the rechargeable battery into fire or water. It can explode. The Rechargeable Battery should not be discarded to domestic refuse, regardless of whether used or unused. You should return it to a local battery collection point in accordance with Battery Regulations or return them to us suitably marked Used Battery. 3

5 Technical Data Model No PT-1136A PT-1136F PT-1136G Rated voltage DC 3.6 V DC 3.6 V DC 3.6 V No-load speed 200 rpm 200 rpm 200 rpm Output torque 2.5N.m 2.5N.m 2.5N.m 6.35mm (1/4") Hex Bit 6.35mm (1/4") Shank Hex Bit Shank Dirver(collect) Overall Length: Straight Overall Length: Angled Battery 270mm (10-13/16") mm (7-23/32") Ni-Mh 3.6V 1000 mah 270mm (10-13/16") mm (7-23/32") Ni-Mh 3.6V 1000 mah 6.35mm (1/4") Hex Bit Shank 270mm (10-13/16") mm (7-23/32") Ni-Mh 3.6V 1000 mah Charging time 5~7 hours 5~7 hours 5~7 hours Free running time min. (unload speed) min. (unload speed) Weight 365g 365g 365g Adaptor 120V AC 60Hz 230V AC 50Hz 6V DC 300mA 6V DC 300mA Protection Class II Complied with EN Indoor operation only min. (unload speed) 220V AC 50Hz 6V DC 300mA Accessory Screwdriver bits in plastic holding set Bit size 11pcs bits 2pcs bits holder SL 3/4/5/6/7mm T10/15/20 PH#1/2/3 Environmental Proection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice 4

6 Product Introduction LED Light LED Light switch Angle Lock Froward& Reverse Switch Charging light indication Initial operation Charging the Battery The rechargeable battery must be charged before the first use. Only recharge the battery once it is has been fully discharged, i.e. the performance clearly decreases. Otherwise the battery may not achieve its full capacity at the subsequent charge. Important! Only use the provided adaptor for charging the battery. When the speed became slowly, charging the battery immediately. The red LED light will light up during the power tool was charging. Please remove the adaptor from the power tool after 5-7 hours. Inserting Tool Bits The machine has a magnet in the slot. You can insert or remove screw bit quickly and easily without any auxiliary tool. Forward / Reverse Switch Use the Forward / Reverse Switch to start the machine and keep holding it for continuous operation. To switch the machine off, release the Forward / Reverse Switch Important! Do not switch quickly. Wait for operating stop, then switch to desire operation, to avoid switch damaged 5

7 LED Light The machine has a built in LED light; it is convenience for working in dark environments. The LED light switch is at the top of handgrip. Simply slide the switch on and off as required when needed. Turn off when not needed so as to save battery life. Operation for working Only use tool bits which can be securely fastened in the chuck and for which the bits has been designed. Before using the machine check whether the screw-bit is inserted correctly. Avoid over-tightening screws, otherwise the screw head may be damaged or stripping of the threads may occur. Screw-bit Insertion Insert the screw-bit into the slot in the head of the screw. Hold the screw bit perpendicular to the head of the screw, otherwise the screw or the screw head may be damaged. Press the forward button, the screw bit against the screw and driving in the screw into work-piece. When the screw is completely screwed in, hold the machine firmly and release switch, otherwise the screw or the screw head may be damaged. Screw-bit Removal Insert the screw-bit into the slot in the head of the screw. Hold the screw-bit perpendicular to the head of the screw, otherwise the screw or the screw head may be damaged. Press the reverse bottom, screw bit against the screw and removing the screw. Maintenance and Clean To clean the power tool, always use a dry or moist, but not wet towel. Many cleaning agents contain chemical substances which may cause damage to the plastic parts of the machine. Therefore do not use any strong or inflammable cleaners such as petrol, paint thinner, turpentine or similar cleaning agents. Always keep air ventilation holes free of dust deposits to prevent overheating. Service For more information on PT-1136A / PT-1136F and other products, please visit 6

8 PT-1136A/F/G 鎳氫充電起子 3.6V 使用說明書使用前請先詳讀本份操作手冊基本安全規則警告 : 沒有按照以下安全注意事項及使用說明操作, 將導致觸電火災或其它嚴重傷害請將本份文件加以保存以供日後所須參考使用 1. 工作區域 a) 請保持工作環境整潔明亮, 混亂昏暗的環境將引發事故 b) 請不要在易爆環境中使用電動工具, 例如在易燃的液體瓦斯或者粉塵環境中電動工具使用時所產生的火花可能點燃粉塵或氣體 c) 工作環境中請勿有孩童及旁觀者, 以免分心造成失誤 2. 電器安全 a) 電動工具插頭請與相配的插座使用請不要以任何方式拆解並改裝插頭, 需接地的電動工具不可使用轉接插頭使用未拆解過的插頭和匹配的插座將減少觸電的風險 b) 請避免讓人體接觸接地表面, 像是管道散熱器爐灶及冰箱等, 如果你的身體接地將會有觸電的風險 c) 請避免讓電動工具暴露在雨中或是潮濕的環境中. 雨水滲入電動工具中會增加觸電的風險 d) 請勿濫用電線絕不用電線搬運拉動電動工具或將插頭拉出 ; 電線必須遠離高溫油膩尖銳或可移動的物體, 受損或纏繞的電線會增加觸電風險 e) 當在戶外操作電動工具時, 請搭配適合戶外使用的外接電線, 以減少觸電風險 f) 如果無法避免在潮濕的環境中使用電動工具, 請使用漏電斷路器 (RCD), 以減少觸電風險 3. 個人安全 a) 請保持高度警覺, 操作電動工具須有基本常識並保持專心, 請勿在身體疲勞服用藥物飲酒及醫事治療後使用電動工具, 否則會導致嚴重的人身傷害 b) 請使用安全裝備永遠配戴護目鏡在適當的狀況下使用安全設備, 如防塵面罩防滑安全鞋, 安全帽, 聽力保護裝置等, 以避免造成人體傷害 c) 為避免電動工具突然啟動, 插電前請先確認開關處於 OFF 位置, 移動電動工具或插電前手指請勿放在開關處, 以免誤觸開關導致事故發生 d) 啟動前務必先移除調整電動工具的鑰匙或扳手, 遺留在電動工具上的鑰匙或扳手在啟動時可能導致人身傷害 e) 操作電動工具時請保持適當距離, 以便在突如其來的狀況發生時能有足夠時間反應及處理 f) 穿著適宜, 請不要穿寬鬆衣服或佩戴首飾請讓您的頭髮, 衣服和手套遠離電動工具寬鬆衣服珠寶或長髮可能會捲入或卡住電動工具. g) 如果有提供排屑和集塵的設備, 請確保他們連接完好且使用得當使用這些裝置可減少粉塵導致的危險 7

9 4. 電動工具的使用及維護 a) 請選擇適當的電動工具請依據您的工作狀況使用正確的電動工具, 可使工作更有效率更安全, 並使電動工具發揮最大效益 b) 當電動工具的啟動開關不能開啟或關閉電源時請停止使用, 請送回原廠修理以免發生危險 c) 當電動工具要進行調整更換配件或儲存不用時, 請先將插頭拔下, 此預防安全措施可降低電動工具意外啟動的風險 d) 電動工具請貯存在兒童無法接觸的地方請不要讓不熟悉或對操作說明不瞭解的人員使用未經訓練的人員操作電動工具會造成危險 e) 電動工具維護 : 請檢查電動工具可調的部位是否到位, 零件是否有破損或是有其它任何可能影響電動工具操作的情形如有損壞, 請先進行修理後才能使用許多事故都是因為電動工具未作好維護而造成的. f) 保持鑽頭 ( 或批頭 ) 鋒利和清潔, 適當的維持在鋒利狀態可減少卡住的狀況且易於使用 g) 依據本操作說明及操作方法, 考量工作環境及需完成的工作, 選用適當的電動工具配件及批頭進行作業選擇不適合的電動工具會產生危險狀況 5. 電池的使用及維護 a) 請使用製造商原裝的變壓器充電, 不適合的變壓器可能會造成火災 b) 請使用製造商原裝的電池包, 使用非製造商原裝的電池包可能造成人身傷害和火災 c) 當電池遭到濫用時, 電池裏的液體可能會滲出, 請勿觸摸如果意外接觸電池液, 請用大量清水沖洗如果眼睛接觸液體, 請立即就醫皮膚接觸噴出的電池液會造成疼痛或燙傷. d) 為確保電動工具電池壽命及效能充分發揮, 請務必充飽電後再使用 e) 非經常性及長時間使用電動工具, 使用時請先確認電池是否有電, 電動工具能正常使用情況下, 建議先使用直至電動工具無法運轉再進行充電 f) 長時間存放電動工具不使用須注意電池自放電情況, 建議每 50 天取出進行一次完全充電 g) 存放電動工具請注意環境溫濕度, 過高 / 過低的溫度將使電池自放電情況加速, 濕度過高容易使電動工具及電池生鏽短路而造成損壞 6. 服務本電動工具的維修或更換零件需由原廠專業維修人員服務, 以確保電動工具的使用安全性關於可充電電池的安全公告請使用原廠所提供的電池及變壓器, 並存放於乾燥區域請勿在戶外使用變壓器當變壓器使用完畢或是在清潔維修前, 請先拔下插頭請勿試圖打開修理電池或變壓器如果任何部件有缺陷, 請由合格的維修技術人員維修或送回原廠維修電池充電的環境溫度為 10 到 40 之間, 已充電的電池可以在 0 到 50 環境溫度下提供電動工具電力進行作業如不使用時, 請儲存在 10 到 30 之間的乾燥環境重要! 危險! 請勿讓電池短路或接觸水氣請勿將電池與金屬物品存放在一起以免造成短路, 電池將產生過熱發燙或爆炸 8

10 如果任何人接觸到電池內部液體或物質, 請立即用大量清水沖洗如果這些物質接觸眼睛, 請立即用清水沖洗後立刻就醫請勿將將充電電池放入水中或火中, 以免發生爆炸無論充電電池是否使用, 均不可當作家用垃圾丟棄您應該按照電池回收條例送到當地國家的電池回收站或是交回給我們並標示為使用過電池規格型號 PT-1136A PT-1136F PT-1136G 額定電壓 DC 3.6V DC 3.6V DC 3.6V 無負載轉速 200rpm 200rpm 200rpm 輸出扭力 2.5 N.M (MAX) 2.5 N.M (MAX) 2.5 N.M (MAX) 工作夾頭 6.35mm( 1/4 ) 內六 6.35mm( 1/4 ) 內六角 6.35mm( 1/4 ) 內六角角插孔插孔插孔電池鎳氫電池 3.6V 鎳氫電池 3.6V 鎳氫電池 3.6V 1000mAh 1000mAh 1000mAh 充電時間 5-7 小時 5-7 小時 5-7 小時可使用時間 30~35 分鐘. ( 無負載 ) 30~35 分鐘. ( 無負載 ) 30~35 分鐘. ( 無負載 ) 長度 270mm 270mm 270mm 重量 365g 365g 365g 輸入 :120V AC 60Hz 變壓器輸出 :6V DC 300mA 防護等級 : II 級符合標準 : EN 適用於室內操作輸入 :230V AC 50Hz 輸出 :6V DC 300mA 輸入 :220V AC 50Hz 輸出 :6V DC 300mA 配件批頭批頭規格 2pcs 延長杆 11pcs 25mm 批頭一字 SL : 3.0 / 4.0 / 5.0 / 6.0 / 7.0mm 星型 : T10 / T15 / T20 十字 PH : #1 / #2 / #3 環境保護廢棄的電器產品請勿當作家用垃圾處理請依當地國家的回收條例送到回收站或是零售商進行回收 9

11 產品功能操作說明 LED 照明燈 LED 照明燈開關角度調節按鈕正反轉切換按鈕充電指示燈基本說明充電首次使用前請先將可充電電池充飽電每次電池完整放電後才能再次進行充電, 以避免電池效率降低除此之外還會造成之後每次充電都無法充飽電的情況發生重要! 請使用原廠所提供的變壓器為電池充電當電力耗盡時請盡快充電, 充電時紅色充電指示燈會亮起, 請控制充電時間在 5~7 小時內, 充電完成請移除變壓器過度消耗電力及過長時間充電都會對電池造成傷害插入批頭本產品夾頭內有磁鐵可吸附批頭, 使用時可直接插入或拔出批頭, 不需特別對準且快速方便正反轉切換按鈕當正反轉按鈕往上按時批頭會向右轉 ( 旋緊 ), 往下按則是向左轉 ( 鬆開 ), 鬆開開關後即停止運轉特别注意! 切換時請待旋轉動作停止後, 再切換下一個動作, 旋轉中直接切換將容易造成機器損傷, 請適當控制切換速度, 以保護開關 LED 照明燈本產品內建 LED 照明燈可提供於昏暗環境進行作業, 照明燈開關位於電動工具上方, 不使用時請隨手關燈以節省電力操作使用請使用合格的批頭產品, 并確認規格符合本產品的裝配尺寸開始操作前請先確認批頭插入是否牢固避免螺絲鎖附過緊造成螺絲頭損傷或滑牙螺絲鎖入請將批頭放入本機夾頭內, 批頭與螺絲對準呈垂直方向, 否則螺絲將造成損壞將批頭對著螺絲按下正轉開關將螺絲鎖緊當螺絲完全鎖緊後, 鬆開正反轉切換按鈕即可 10

松香水, 松節油及其它類似的清潔劑本機通風孔請防止灰塵沉積以免過熱服務更多關於 PT-1136A / PT-1136F

12 螺絲旋出請將批頭放入本機夾頭內, 批頭與螺絲呈垂直方向, 否則螺絲將造成損壞將批頭對著螺絲按下反轉開關將螺絲旋出維護和清潔請使用乾的或是微濕的毛巾進行清潔許多清潔劑含有化學物質, 可能會使機器的塑膠部位造成損壞因此請勿使用其它較強烈或易燃的清洗劑像是汽油松香水, 松節油及其它類似的清潔劑本機通風孔請防止灰塵沉積以免過熱服務更多關於 PT-1136A / PT-1136F 的資訊及其它產品, 請上本公司網站 2015 Prokit s Industries Co., LTD. All rights reserved (C) 11

000Book_SV12SH.indb

000Book_SV12SH.indb Orbital Sander SV 12SH Handling instructions Read through carefully and understand these instructions before use. 1 2 1 1 3 4 A B 3 4 2 5 5 English 1 Sanding paper 2 Dust gate 3 Dust bag 4 Dust outlet