A D B E C 2 1 2

Size: px

Start display at page:

Download "A D B E C 2 1 2"

聆溲被燕
5 years ago
Views:

1 ISD72 English (original instructions) 4 9

2 A D B E C 2 1 2

3 7.2V IMPACT SCREWDRIVER ISD72 Technical Data Specifications: ISD72 Voltage 7.2V No load speed 2200 Chuck size 6.35 Weight 640g Battery Voltage V 7.2 Capacity Ah 1.3 Type Li-lon Charger Input Voltage V 110V Output Voltage V 8V (Max) Current 100ma Approx. charge time 13 Hours SAFETY GUIDELINES - DEFINITIONS It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially haz ard ous situation which, if not avoided, may result in minor or mod er ate injury. NOTICE: Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in property damage. This tool is intended for consumer use only. Safety instructions GENERAL POWER TOOL SAFETY WARNINGS WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. 3 SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE The term power tool in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS 1) WORK AREA SAFETY a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2) ELECTRICAL SAFETY a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock. 3) PERSONAL SAFETY a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are

4 tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, nonskid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/ or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions 4 to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) Battery tool use and care a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. b) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. c) When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. d) Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. 6) Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

5 Specific Safety Rules Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a live wire may make exposed metal parts of the power tool live and could give the operator an electric shock. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control. When not in use, place tool on its side on a stable surface where it will not cause a tripping or falling hazard. Some tools with large battery packs will stand upright but may be easily knocked over. save these instructions Symbols The label on your tool may include the following symbols. The symbols and their definitions are as follows: V...volts A...amperes Hz...hertz W...watts min...minutes or AC...alternating current or DC...direct current no...no load speed...class I Construction (grounded)...earthing terminal...safety alert symbol...class II Construction (double insulated).../min or rpm...revolutions or reciprocation per minute SPM...Strokes per minute...read instruction manual before use...use proper eye protection...use proper hearing protection...use proper respiratory protection 5 Functional Description 1. Variable speed trigger 2. Forward/reverse button 3. Quick-release chuck 4. Magnetic bit holder 5. Charging port 6. Charging indicator 7. Charger safety warnings AND INSTRUCTIONS - BATTERIES Do not disassemble or open, drop (mechanical abuse), crush, bend or deform, puncture, or shred. Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, or expose to fire, excessive heat including soldering irons, or put in microwave oven. Only use the battery with a charging system specified by the manufacturer/supplier. Do not short-circuit a battery or allow metallic or conductive objects to contact both battery terminals simultaneously. Dispose of used batteries promptly according to the manufacturer/supplier s instructions. Improper battery use may result in a fire, explosion, or other hazard. Battery usage by children should be supervised. WARNING: Never attempt to open the battery for any reason. If battery case is cracked or damaged, do not insert into charger. Do not crush, drop or damage battery. Do not use a battery or charger that has received a sharp blow, been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer, stepped on). Damaged batteries should be returned to service center for recycling. safety warnings AND INSTRUCTIONS - CHARGING 1. This manual contains important safety and operating instructions. 2. Before using battery charger, read all instructions and cautionary warnings on battery charger and product using battery. CAUTION: To reduce the risk of injury, use charger only with this product. Batteries in other products may burst causing personal injury or damage.

6 3. Do not expose charger to rain or snow. 4. Use of an attachment not recommended or sold by Black & Decker may result in a risk of fire, electric shock, or injury to persons. 5. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger. 6. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. 7. An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire, electric shock or electrocution. a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round jacketed extension cords should be used, and we recommend that they be listed by Underwriters Laboratories (U.L.). If the extension is to be used outside, the cord must be suitable for outdoor use. Any cord marked for outdoor use can also be used for indoor work. The letters W or WA on the cord jacket indicate that the cord is suitable for outdoor use. b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety, and to prevent loss of power and overheating. The smaller the gauge number of the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each extension contains at least the minimum wire size. Chart for minimum wire size (AWG) of Extension Cords Nameplate rating AMPS Total Extension Cord Length (ft) (0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m) Wire Gauge Use only the supplied charger when charging your tool. The use of any other charger could damage the tool or create a hazardous condition. 9. Use only one charger when charging. 10.Do not attempt to open the charger. There are no customer serviceable parts inside. Return to any authorized Black & Decker service center. 11.DO NOT incinerate the tool or batteries even if they are severely damaged or completely worn out. The batteries can explode in a fire Do not incinerate the battery even if it is severely damaged or is completely worn out. The batteries can explode in a fire. Toxic fumes and materials are created when lithium ion batteries are burned. 13. Do not charge or use battery in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Inserting or removing the drill from the charger may ignite the dust or fumes. 14. If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for three minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts. WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame. CHARGING PROCEDURE THE BATTERIES IN YOUR TOOL ARE NOT FULLY CHARGED AT THE FACTORY. BEFORE ATTEMPTING TO CHARGE THEM, THOROUGHLY READ ALL OF THE SAFETY INSTRUCTIONS. To charge your tool, follow the steps below. 1. Plug the charger (7) into electrical outlet. 2. Insert the charger into the charging port (5), making sure to line up the keyed plug with the port as shown in figure A. The charging indicator LED (6) will flash, indicating the battery inside the drill is being charged. The completion of charge is indicated by the LED remaining on continuously. important charging notes 1. Your tool was sent from the factory in an uncharged condition. Before attempting to use it, it must be charged for at least 9 hours. 2. DO NOT charge the batteries in an air temperature below 40 F (4,5 C) or above 105 F (40,5 C). This is important and will prevent serious damage to the batteries. Longest life and best performance can be obtained if batteries are charged when air temperature is about 75 F (23,8 C). 3. While charging, the charger may hum and become warm to touch. This is a normal condition and does not indicate a problem.

7 4. If the batteries do not charge properly (1) Check current at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. (3) Move charger and tool to a surrounding air temperature of 40 F (4,5 C) to 105 F (40,5 C). (4) If the receptacle and temperature are ok, and you do not get proper charging, take or send the tool and charger to your local Black & Decker service center. See Tools Electric in yellow pages. 5. The tool should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using product with its batteries in a depleted condition. operating instructions Quick Release Chuck (figure B) To install an accessory: Hold the tool as shown in figure B and push the chuck collar away from the tool. Insert a hex shank accessory and release the collar. The accessory is locked in place. NOTE: Use 2 bits or 1 bits with a bit tip holder (not provided). To remove an accessory: Hold the tool as shown in figure B and push the chuck collar away from the tool. Remove the accessory and release the collar. Trigger Switch & Reversing Button (Figure C) The drill is turned ON and OFF by pulling and releasing the trigger (1). A forward/reverse control button (2) determines the direction of the tool and also serves as a lock off button. To select forward rotation, release the trigger switch and depress the forward/reverse control button to the left. To select reverse, depress the forward/ reverse control button the opposite direction. To avoid being turned on accidentally, do not carry in your pocket. NOTE: The center position of the control button locks the tool in the off position. When changing the position of the control button, be sure the trigger is released. Screw Driving For driving fasteners, the foward/reverse button should be pushed to the left. Use reverse (button pushed to the right) for removing fasteners. When moving from forward to reverse, or vice versa, always release the trigger switch first. Release trigger when the fastener is at the desired depth. NOTE: For best performance, use 2 fasteners or smaller, or screw into pre-drilled holes. NOTE: The impact mechanism of the screwdriver creates a loud, impacting noise when extra force is needed. This noise is normal; the screwdriver is not malfunctioning or broken. Impact Driver Warnings: Hold the tool as shown in figure D. Do not use tool as a pry bar. To avoid being turned on accidentally, do not carry in your pocket. on board bit storage (Figure E) A magnetic bit holder(4) is built-in to the area on top of the screwdriver for easy storage and access. Drilling Use sharp drill bits only. Screwdriver is ideal for bits 1/4 or smaller. Support and secure work properly, as instructed in the Safety Instructions. Use appropriate and required safety equipment, as instructed in the Safety Instructions. Secure and maintain work area, as instructed in the Safety Instructions. Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit. DO NOT CLICK THE TRIGGER OF A STALLED SCREWDRIVER OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE SCREWDRIVER CAN RESULT. Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last part of the hole. Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming. Make sure switch turns screwdriver on and off. 7

8 maintenance Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts. LUBRICATION Your tool was properly lubricated before leaving the factory. Once every year take or send your tool to a Black & Decker service center, or authorized service station, for a complete cleaning, inspection and lubrication. Tools out of service for long periods should be relubricated before being put back to work. WARNING: Since accessories, other than those offered by Black & Decker, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only Black & Decker recommended accessories. CLEANING Use only mild soap and a slightly damp cloth to clean your angle grinder. Many household cleaners contain chemicals which could seriously damage the plastic. Also, do not use petrol, turpentine, lacquer or paint thinners or similar products. Never let any liquid get inside the tool and never immerse any part of the tool into liquid. of it with household waste. Make this product available for separate collection. Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials. Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product. SERVICE INFORMATION Black & Decker offers a full network of companyowned and authorized service locations. All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. For more information about our authorized service centers and if you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. Notes Black & Decker s policy is one of continuous improvement to our products and, as such, we reserve the right to change product specifications without prior notice. Standard equipment and accessories may vary by country. Product specifications may differ by country. Complete product range may not be available in all countries. Important! To assure product SAFETY and RE- LIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts. PROTECTING THE ENVIRONMENT Separate collection. This product must not be disposed of with normal household waste. Should you find one day that your Black & Decker product needs replacement, or if it is of no further use to you, do not dispose 8

9 7.2V ISD72 ISD72 7.2V g V 7.2 Ah 1.3 V 110V V 8V - 100ma 13 / 1) a) b) c) 2) a) b) c) d) e) 9

10 f) (GFCI) GFCI 3) a) b) c) / d) e) f) g) 4) a) b) c) / d) e) f) g) 5) a) b) c) d) 10

11 6) a) V... A... Hz... W... min... AC... DC... no......i ii.../ /... SPM / / / 11

12 Black & Decker a. Underwriters Laboratories (U.L.) WWA b. AWG (AWG) AMPS (0-7.6m) ( m) ( m) ( m) Black & Decker (7) 2. (5) A 12

13 LED (6) LED B F (4.5 C) 105 F (40.5 C) 75 F (23.8 C) (1) (2) (3) 40 F (4.5 C) 105 F (40.5 C) (4) Black & Decker - 5. B B 2 1 C (1) / (2) / / off / 2 D E (4) 13

14 1/4 Black & Decker Black & Decker Black & Decker Black & Decker Black & Decker Black & Decker Black & Decker 14

15 Black & Decker / / 15

16 /2013

000Book_SV12SH.indb

000Book_SV12SH.indb Orbital Sander SV 12SH Handling instructions Read through carefully and understand these instructions before use. 1 2 1 1 3 4 A B 3 4 2 5 5 English 1 Sanding paper 2 Dust gate 3 Dust bag 4 Dust outlet