CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future

Transcription

1 LV Front Surround System Owner s Manual Manual de Instrucciones

2 CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. Install this unit in a well ventilated, cool, dry, clean place - away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. For proper ventilation, allow the following minimum clearances. Top: 10 cm (4 in), Rear: 10 cm (4 in), Sides: 10 cm (4 in) Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury. Avoid installing this unit where foreign objects may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: Other components, as they may cause damage and/or discoloration on the surface of this unit. Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury. Containers with liquid in them, as they may fall and liquid may cause electrical shock to the user and/or damage to this unit. Do not cover this unit with a newspaper, tablecloth, curtain, etc., in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury. Do not plug in this unit to a wall outlet until all connections are complete. Do not operate this unit upside-down. It may overheat, possibly causing damage. Do not use force on switches, knobs and/or cords. When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cable. Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. Yamaha will not be held responsible for any damage resulting from use of this unit with a voltage other than specified. To prevent damage by lightning, keep the power cable and outdoor antennas disconnected from a wall outlet or the unit during a lightning storm. Do not attempt to modify or fix this unit. Contact qualified Yamaha service personnel when any service is needed. The cabinet should never be opened for any reasons. When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet. Be sure to read the Troubleshooting section on common operating errors before concluding that this unit is faulty. Before moving this unit, press to set this unit in standby mode, and disconnect the power supply cable from the wall outlet. Condensation will form when the surrounding temperature changes suddenly. Disconnect the power supply cable from the outlet, then leave the unit alone. Install this unit near the wall outlet and where the AC power plug can be reached easily. Secure placement or installation is the owner s responsibility. Yamaha shall not be liable for any accident caused by improper placement or installation of speakers. Keep the product out of reach of children to avoid them swallowing small parts. Notes on remote controls and batteries Do not spill water or other liquids on the remote control. Do not drop the remote control. Do not leave or store the remote control in the following places: places of high humidity, such as near a bath places of high temperatures, such as near a heater or a stove places of extremely low temperatures dusty places Do not expose the remote control sensor of this unit to direct sunlight or lighting such as inverted fluorescent lamps. If the batteries grow old, the effective operation range of the remote control decreases considerably. If this happens, replace the batteries with two new ones as soon as possible. Do not use old batteries together with new ones. Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color. Exhausted batteries may leak. If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. Do not carry batteries in a pocket or purse with metal objects like coins, etc. Do not throw away batteries with general house waste. Dispose of them correctly in accordance with your local regulations. Keep batteries away from children. If a battery is accidentally swallowed, contact your doctor immediately. When not planning to use the remote control for long periods of time, remove the batteries from the remote control. Do not charge or disassemble the supplied batteries. The batteries shall not be exposed to excessive heat such as sunshine, fire or like. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by. In this state, this unit is designed to consume a very small quantity of power. (Power key) Turns on the power of this unit or sets it to the standby mode. Do not use this unit within 22 cm (9 inches) of persons with a heart pacemaker implant or defibrillator implant. Radio waves may affect electro-medical devices. Do not use this unit near medical devices or inside medical facilities. The name plate is located on the bottom of the unit. i En

3 Contents Supplied items... 2 Features... 3 Frequently asked questions... 3 Part names and functions... 4 Installation... 5 Connections... 6 Operations... 8 Listening to the sound from a Bluetooth device Settings Programming the sound bar with the TV s remote control (TV s remote control learning function) Using an external subwoofer Setting the auto power standby function Initializing the sound bar Troubleshooting Specifications About this manual NOTE This indicates precautions for use of the product and its feature limitations. HINT This indicates supplementary explanations for better use. En 1

4 Supplied items Make sure you have received all of the following items. Preparing the remote control Peel off the protection sheet before use. Sound bar Remote control Battery x 2 (AAA, R03, UM4) Optical cable (1.5 m [4.9 ft]) Operating range of the remote control Remain within the operating range shown below. When attaching the sound bar to a wall, operate with the remote control sensor on the top panel (p.5). Remote control sensor Within 6 m (20 ft) Mounting template * Use when attaching the sound bar to a wall Spacer 2 * Use when attaching the sound bar to a wall Owner s Manual (This manual) 2 En

5 Features Enjoy powerful and realistic sound from the sound bar with built-in subwoofer, and easy installation and connection to a TV and other devices. AIR SURROUND XTREME Enjoy 7.1 channel surround sound, which creates a wide and deep soundstage, as if speakers are set, not only on the front, but also on the left and right, and behind the listener (p.9). Bass extension Enjoy a powerful bass sound with the Yamaha original bass boost technology Advanced Bass Extension Processing (p.9). Bluetooth connection Content on a Bluetooth compatible smartphone, tablet, or computer can be played back easily (p.10). You can enjoy realistic and impressive sound as close to the original by the Compressed Music Enhancer. HOME THEATER CONTROLLER You can operate the sound bar easily by installing the dedicated controlling application HOME THEATER CONTROLLER. TV s remote control learning function Operate the sound bar with the TV s remote control (p.12). Frequently asked questions The following section covers popular functions and frequently asked questions about the sound bar. Q1 A1 Q2 A2 Q3 A3 Can I operate the sound bar using the remote control of the TV? Switching between the remote controls of the TV and sound bar is inconvenient. Yes. You can control the sound bar using your TV s remote control by the TV s remote control learning function (p.12). This function is available only for the IR (infrared) remote control. Check your TV s remote control type. Can I improve the clarity of dialogue? Yes. Dialogue in movies, TV news, sports programs, etc., can be made clearer using the clear voice function (p.9). Can I operate the sound bar using a smartphone? And, can I turn on/off the sound bar with a smartphone? Yes. You can operate the sound bar with your smartphone by using the dedicated control application HOME THEATER CONTROLLER (p.11). When using this function, it is necessary to connect your smartphone to the sound bar through Bluetooth connection. Also, if you use the Bluetooth standby mode function, the sound bar will turn on when a Bluetooth connection is made between your smartphone and the sound bar, and turns off when disconnected (p.11). Clear voice Makes voice sound (such as dialogues and narrations) clear (p.9). En 3

6 Part names and functions Sound bar (front panel/top panel) Sound bar (rear panel/bottom panel) * * * * * Keys are located in the rear part of the sound bar. * * Bottom panel A Indicators Indicate the status of the sound bar. Refer to Operations (p.8 to 9) for the main functions of the indicators. B (input) key Selects an input source to be played back (p.8). C (mute) key Mutes the audio output. Press the key again to unmute (p.9). D / (volume +/-) keys Adjust the volume (p.8). E (power) key Turns on or off (standby) the sound bar (p.9). HINT The sound bar may automatically turn off when the auto power standby function is enabled (p.15). F Remote control sensors Receive infrared signals from the remote control of the sound bar (p.2). The remote control sensors are located on the front panel and on the top panel of the sound bar (p.5). G Dual built-in subwoofers The built-in subwoofers are located in the top part of the sound bar. H Speakers I TV input jack For connecting to a TV with an optical cable (p.6). J BD/DVD input jack For connecting to a playback device, such as a Blu-ray Disc (BD) player, with a coaxial digital cable (p.7). K ANALOG input jack For connecting an external device with a 3.5 mm stereo mini plug cable (p.7). L SUBWOOFER OUT jack For connecting an external subwoofer with a monaural pin cable (p.14). M Installation position selector switch Sets the sound quality appropriate to the installation position of the sound bar (p.5). 4 En

7 Installation The orientation of the sound bar and the appropriate remote control sensor depend on the installation location. Installing the sound bar on a TV cabinet, etc. 1 Slide the installation position selector switch on the bottom panel of the sound bar to the T (for Tabletop) side (T, by default). The sound quality appropriate to the installation will be set. 2 Place the sound bar on a TV cabinet, etc., so that the keys are facing the wall. Attaching the sound bar to a wall 1 Slide the installation position selector switch on the bottom panel of the sound bar to the W (for Wall mount) side. The sound quality appropriate to the installation will be set. 2 Following How to install on the wall below, install the sound bar so that the keys face upwards. Remote control sensor (top panel) Keys Installation position selector switch (bottom panel) 2 Remove the mounting template from the wall, then install commercially available screws (as illustrated below) at the points marked on the wall. 7 to 9 mm (1/4" to 3/8") 10 to 12 mm (3/8" to 1/2") 3 Peel off the backing paper from the spacers and attach the adhesive face to the sound bar as illustrated below. Spacer 4 Hang the sound bar on the screws. 4 mm (#8) 20 mm (3/4") or more Installation position selector switch (bottom panel) Remote control sensor (front panel) Cautions Do not stack the sound bar and a BD player or other device directly on each other. Doing so may cause a malfunction due to vibrations. Do not hold the speaker portion (fabric parts) on the front and the top of the sound bar. The sound bar contains non-magnetic shielding speakers. Do not place magnetically sensitive items (hard disk drive, etc.) near the sound bar. Depending on your installation environment, it may be better to connect the sound bar and external devices (such as a TV) before installing the sound bar. Do not place the sound bar within 50 mm (2") of the TV. Cautions When installing the sound bar on a wall, all installation work must be performed by a qualified contractor or dealer. The customer must never attempt to perform this installation work. Improper or inadequate installation could cause the sound bar to fall, resulting in personal injury. Do not attach the sound bar to a wall that is made of weak materials such as plaster or veneered woods. Doing so may cause the sound bar to fall. Make sure you use commercially available screws that can support the weight of the installation (specified in Step 2 on the right). Using clamps other than specified screws, such as short screws, nails, and two-sided tape, may cause the sound bar to fall. How to install on the wall 1 Attach the mounting template on a wall and mark for the screw holes. Tapes or thumbtacks Mounting template (supplied) Screw holes Mounting holes on bottom of sound bar Cautions Fix the cables in place where they will not become loose. If your foot or hand accidentally gets caught on a loose cable, the sound bar may fall. Check that the sound bar is fixed securely after the installation. Yamaha will bear no responsibility for any accidents caused by improper installations. En 5

8 Connections Connect to a TV (or other peripheral device). Sound bar (rear) CAUTIONS Do not connect the power cable of the sound bar to the AC wall outlet before making connections. Do not use excessive force when inserting the cable plug. Doing so may damage the cable plug or terminal. Power cable To AC wall outlet 1 Connect the TV and sound bar with the optical cable (supplied). Remove the cap of the optical cable and check the direction of the plug. Optical cable 2 Connect the power cable of the sound bar to an AC wall outlet. 3 Set the TV as follows. Set the TV volume to minimum. Disable the TV built-in speaker output (if available). TV OPTICAL OUTPUT HINT If a setting to disable the speaker output is not available on your TV, you may disable it by connecting headphones to the headphone jack on the TV. For details, refer to the manuals of the TV. The TV and BD/DVD input jacks support the following audio signals. PCM (2 channel) Dolby Digital (up to 5.1 channel) HDMI cable (etc.) Playback device (such as a BD player) Set top box HINT In the following cases, connect the coaxial digital audio output of the playback device to the BD/DVD input of the sound bar with a coaxial digital cable (commercially available), then select the BD/DVD key on the remote control for the input source. The TV does not have an optical output. The TV does not output audio (or outputs low volume audio) from the connected playback device. The audio from the playback device connected to the TV cannot be heard as surround sound. 6 En

9 Digital connection of an external device You can connect an external device that has a coaxial digital audio output, such as a DVD player, to the BD/DVD input jack of the sound bar. Analog connection of an external device (game console) You can connect an external device, such as a game console or TV that does not have a digital audio output, to the ANALOG input jack of the sound bar. Coaxial digital cable (commercially available) 3.5 mm stereo mini plug cable (commercially available) Coaxial digital audio output (orange) Playback device Game console (etc.) NOTE Select the BD/DVD key on the remote control for the input source. NOTE Select the ANALOG key on the remote control for the input source. If you can adjust the volume on an external device connected to the ANALOG input jack of the sound bar, adjust it to the same volume as the external device connected to the TV or BD/DVD input jack. En 7

10 Operations Indicators The indicators on the top panel flash or light up, to indicate the operation and setting status. 1 Input keys Select an input source to be played back. TV...TV audio BD/DVD...Audio from a device connected to the BD/DVD input jack ANALOG...Audio from a device connected to the ANALOG input jack BLUETOOTH...Audio from a Bluetooth connected device The indicator for the selected input source lights up. (Example: when TV is selected) : Keys that require pressing for more than 3 seconds LEARN, BLUETOOTH STANDBY, AUDIO DELAY Remote control signal transmitter Transmits infrared signals. In this manual, illustrations of the nine in-line indicators are used for explanation. : Off : Lights up : Flashes (Example: When the PLII indicator and SURROUND indicator flash, and the TV indicator lights up) HINT To play audio of the playback device connected to the TV or to watch videos of the playback device, set the TV s input source to the playback device. For details on Bluetooth connection, refer to Listening to the sound from a Bluetooth device (p.10). SUBWOOFER keys (+/-) Adjust the volume of the subwoofer. 2 Volume down ( ) Volume up (+) VOLUME keys (+/-) Adjust the volume of the sound bar. Volume down ( ) Volume up (+) LEARN key Sets the sound bar to the TV s remote control learning mode (p.12). BLUETOOTH STANDBY key Enables/disables the Bluetooth standby mode (p.11). 3 8 En

11 (power) key 4 BASS EXTENSION key 6 MUTE key 7 Turns on or off (standby) the sound bar. Turned on Indicator of the selected input source lights up (green) Bluetooth standby (p.11) Enables/disables the bass extension function. When this function is enabled, you can enjoy a powerful bass sound with the Yamaha original bass boost technology Advanced Bass Extension Processing. Lights up (enabled) Mutes the audio output. Press the key again to unmute. Flash (on mute) Lights up (red) Turned off DIMMER key Switches the brightness of the indicators. Pressing the key each time switches the status of the indicators as follows. Dim (default setting) Off Bright Indicators illuminate bright just after the operation and become the set brightness after a few seconds. SURROUND and STEREO keys Switch between surround and stereo (2 channel) playback. When surround playback is selected, you can enjoy a realistic sound effect using Yamaha s exclusive AIR SURROUND XTREME. SURROUND Lights up (surround playback) STEREO Off (stereo playback) HINT When 2 channel stereo signals are played in surround, the PLII indicator lights up. 5 Lights up (Dolby Pro Logic II) By installing the dedicated free application HOME THEATER CONTROLLER to a Bluetooth device, such as a smartphone, you can choose the following surround modes: TV PROGRAM, MOVIE, MUSIC, SPORTS, and GAME. CLEAR VOICE key Enables/disables the clear voice function. When this function is enabled, you can enjoy clear voice sounds while watching movies, TV dramas, news programs or sports programs. Off (disabled) Lights up (enabled) Off (disabled) AUDIO DELAY key Adjusts the audio delay to synchronize the sound with the video when the video image on the TV may seem delayed with respect to the sound. Follow the procedure below to adjust the audio delay. 1 Hold down the AUDIO DELAY key for more than 3 seconds. The left most indicator flashes. 2 Press the SUBWOOFER (+/-) key to adjust the audio delay. Pressing the SUBWOOFER (+) key delays the audio output timing. ( ) (+) 3 To finish the adjustment, press the AUDIO DELAY key. HINT The adjustment will be finished automatically if no operations are performed for 20 seconds. Decoder indication The sound bar supports the following audio signals. You can check the type of the input audio signal by the color of the indicator. Green (Dolby Digital) Off (PCM) En 9

12 Listening to the sound from a Bluetooth device You can play back wirelessly from Bluetooth devices, such as a smartphone or digital music player. See also the operating manual of the Bluetooth device for more details. Pairing a Bluetooth device with the sound bar When connecting to a Bluetooth device for the first time, pairing between the device and sound bar is required. Pairing is necessary for each Bluetooth device you use. Once pairing with a device is completed, subsequent connection with that device will not require pairing. 1 Press the BLUETOOTH key on the sound bar s remote control to select Bluetooth as the input source. The BLUETOOTH indicator on the top panel flashes. Bluetooth devices Flashes 2 Turn on the Bluetooth function of the device to be paired, and perform pairing. The operation varies depending on the device. Refer to the operation manual of the device. 3 Select YAS-105 Yamaha in the Bluetooth device list on the device. If a passkey (PIN) is required, enter the number Perform the following steps to use a Bluetooth device with the sound bar. For the first Bluetooth connection For subsequent Bluetooth connection YAS-105 Yamaha PIN Pairing a Bluetooth device with the sound bar Playing back audio from a Bluetooth device on the sound bar NOTE When pairing is completed, or a completion message appears on the device. Perform pairing with the Bluetooth device and sound bar within 10 meters (33 ft) of each other. Up to eight Bluetooth devices can be paired with the sound bar. If a ninth device is paired, pairing data for the device with the oldest connection date will be deleted. If pairing information for a device is deleted, to use that device again, pairing of the device is required again. If a Bluetooth device is already connected to the sound bar, terminate that Bluetooth connection (p.11), then perform pairing with the new device. Refer to Bluetooth (p.18) in Troubleshooting if pairing cannot be achieved. 10 En

13 Playing back audio from a Bluetooth device on the sound bar 1 With the sound bar turned on, press the BLUETOOTH key on the sound bar s remote control to select Bluetooth as the input source. The BLUETOOTH indicator on the top panel flashes. Flashes 2 Turn on the Bluetooth function of the device and then connect. When Bluetooth connection is made correctly, the BLUETOOTH indicator of the sound bar lights up. Using the Bluetooth standby mode The Bluetooth standby mode allows you to turn on (or off) the sound bar automatically, linked with the operation of the Bluetooth device. 1 With the sound bar turned on, hold down the BLUETOOTH STANDBY key on the sound bar s remote control for more than 3 seconds. Holding down the BLUETOOTH STANDBY key for 3 seconds each time toggles the mode between enabled and disabled. Flash 3 times (enabled), flash once (disabled) When the Bluetooth standby mode is enabled and the sound bar is turned off, the D indicator lights up in red (Bluetooth standby). Lights up 3 Play back a song on the device. Lights up (red) Functions available on Bluetooth devices with Bluetooth standby mode enabled Power on interlock function (when the sound bar is turned off) When Bluetooth connection is made on the device, the sound bar will turn on and will be ready to play back sound from the device. NOTE Perform Bluetooth connection with the device and sound bar within 10 meters (33 ft) of each other. It may be necessary to select YAS-105 Yamaha in the Bluetooth device list again, in the event that a connection problem occurs. You may have to change the output setting to output audio to the sound bar, depending on the Bluetooth device you are using. Adjust the volume level of the Bluetooth device as required. If a Bluetooth device is already connected to the sound bar, terminate that Bluetooth connection, then connect with the new device. Terminating Bluetooth connection Bluetooth connection is terminated in the following cases. When the Bluetooth connection is terminated with the sound bar turned on, the BLUETOOTH indicator changes from the lit status to the flashing status and the sound bar enters the connection wait status. The Bluetooth function is turned off on the compatible device. The BLUETOOTH key on the sound bar s remote control is pressed for more than 3 seconds. The sound bar is turned off. Power off interlock function (when the sound bar is turned on) The sound bar will be turned off when Bluetooth connection is terminated on a Bluetooth device. (Only when BLUETOOTH is selected as the input source.) Using the HOME THEATER CONTROLLER application By installing the dedicated free application HOME THEATER CONTROLLER to a Bluetooth device, such as a smartphone, you can perform various operations easily and conveniently with the Bluetooth device. (Setting items: basic operation, surround mode, sound adjustments) NOTE To use the application, connect the sound bar and a Bluetooth device via Bluetooth connection. If you enable the Bluetooth standby mode of the sound bar, you can turn on the power of the sound bar with the Bluetooth device. For details on HOME THEATER CONTROLLER, see the product information on our website. En 11

14 Settings Programming the sound bar with the TV s remote control (TV s remote control learning function) Once you program the sound bar, you can control it with your TV s remote control for functions such as turning on/off the TV and sound bar simultaneously, or volume up/ down and muting/unmuting of the sound bar. This function is available only when your TV s remote control uses IR (infrared) signal. A radio wave remote control will not work. If you want to use a cable or satellite set top box s remote control to operate the sound bar, use your original TV s IR (infrared) remote control to program the sound bar, then use the set top box s remote control to operate. If by changing the volume of the sound bar the TV s volume also changes, set the TV s volume to minimum, or disable speaker output. NOTE Steps 5 to 8 require only the TV s remote control and the keys on the rear panel of the sound bar. The remote control of the sound bar is not necessary. If the sound bar has already learned functions, the following indicators light up. Mute: TV Volume (-): BD/DVD Volume (+): ANALOG Power: BLUETOOTH 5 Teach the sound bar the Mute code of the TV s remote control. 5-1 Press (mute) on the rear panel of the sound bar. 5-2 While pointing your TV s remote control at the remote control sensor, hold down the mute key for more than 1 second twice or three times. The appropriate remote control sensor depends on the installation position (p.5). 1 Turn off the TV. 2 Turn off the sound bar. 3 Hold down the LEARN key on the sound bar s remote control for more than 3 seconds while pointing at the appropriate remote control sensor (p.5). The sound bar enters the learning mode, and the indicators on the top panel flash as shown below. Approx. 30 cm (1 ft) TV s remote control Hold down (more than 1 second) Release (more than 1 second) Hold down (more than 1 second) Release (...) 4 Check if the appropriate remote control sensor has been activated. You can check which remote control sensor has been activated with the CLEAR VOICE indicator. Successfully learned Once Lights up Result Bleep/buzzer Indicators CLEAR VOICE indicator Off Lights up Activated remote control sensor On the front panel On the top panel Activated remote control sensor is appropriate when Installing the sound bar on a TV cabinet, etc. Attaching the sound bar to a wall Failed to learn * Repeat from Step 5-1. Twice Flash If the appropriate remote control sensor has not been activated, press the LEARN key to exit from the learning mode, and repeat from Step En

15 6 Teach the sound bar the Volume ( ) code of the TV s remote control. 6-1 Press (volume -) on the rear panel of the sound bar. 8 Teach the sound bar the Power code of the TV s remote control. 8-1 Press (power) on the rear panel of the sound bar. 6-2 While pointing your TV s remote control at the remote control sensor, hold down the volume ( ) key for more than 1 second twice or three times. Result Bleep/buzzer Indicators 8-2 While pointing your TV s remote control at the remote control sensor, hold down the power key for more than 1 second twice or three times. Result Bleep/buzzer Indicators Successfully learned Once Lights up Successfully learned Once Lights up Failed to learn * Repeat from Step 6-1. Twice Flash Failed to learn * Repeat from Step 8-1. Twice Flash 7 Teach the sound bar the Volume (+) code of the TV s remote control. 7-1 Press (volume +) on the rear panel of the sound bar. 7-2 While pointing your TV s remote control at the remote control sensor, hold down the volume (+) key for more than 1 second twice or three times. Result Bleep/buzzer Indicators Successfully learned Once Lights up 9 To finish the learning mode, press the LEARN key on the sound bar s remote control. This completes the necessary settings. Now you can operate the sound bar with the TV s remote control s mute key, volume keys, or power key. HINT The learning mode will be finished automatically if no operations are performed for 5 minutes. Set the TV volume to minimum. When you turn up the volume of the sound bar with the TV s remote control, the volume of the TV may be turned up at the same time. In this case, follow Step 3 in Connections (p.6) to change the TV setting. You can press the (power) key on the sound bar s remote control to finish learning mode. Failed to learn * Repeat from Step 7-1. Twice Flash En 13

16 Clearing all programmed functions 1 With the sound bar turned off, hold down the LEARN key on the sound bar s remote control for more than 3 seconds (for entering the learning mode). When the sound bar is in the learning mode, the indicators on the top panel flash as shown below. Using an external subwoofer The sound bar has dual built-in subwoofers; however you can connect an external subwoofer when you want to enhance low frequency sound. Connect a subwoofer to the SUBWOOFER OUT jack of the sound bar. Sound is output from both the built-in subwoofers and external subwoofer. 2 Hold down (input) on the rear panel of the sound bar for more than 3 seconds. The corresponding indicator of the learned function turns off and the indicators on the top panel flash as shown below. Pin cable for subwoofer (commercially available) If the clearing is completed, you will hear the bleep sound three times. 3 Press the LEARN key on the sound bar s remote control. Mono input NOTE Use an external subwoofer with built-in amplifier. 14 En

17 Setting the auto power standby function By enabling the auto power standby function, you can avoid forgetting to turn off the sound bar after use, or if you fall asleep while watching TV. NOTE When the auto power standby function is enabled and one of the following conditions is met, the sound bar will automatically turn off. No operations for 8 hours No audio input and no operations for 20 minutes when BLUETOOTH is selected as the input source. 1 With the sound bar turned off, hold down the MUTE key on the sound bar s remote control for more than 3 seconds to enable/disable the auto power standby function. You can check the status of the auto power standby function with the indicators on the top panel for several seconds right after the sound bar is turned on. Initializing the sound bar Follow the procedure below to initialize the sound bar. 1 Turn off the sound bar. 2 Hold down (power) on the rear panel of the sound bar for more than 3 seconds. Flash (initialized) Off (enabled), lights up (disabled) HINT Initial setting varies depending on the country or region. U.K. and Europe models: enabled Other models: disabled En 15

18 Troubleshooting Refer to the table below when the sound bar does not function properly. If the problem you are experiencing is not listed below or if the instructions below do not help, turn off the sound bar, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. First, check the following: A The power cables of the sound bar, TV and playback devices (such as BD players) are connected to AC wall outlets securely. B The sound bar, TV and playback devices (such as BD players) are turned on. C The connectors of each cable are securely inserted into jacks on each device. Power and system Problem Cause Remedy The power turns off suddenly. The auto power standby function worked. When the auto power standby function is enabled and one of the following conditions is met, the sound bar will automatically turn off. - No operations for 8 hours - No audio input and no operations for 20 minutes when BLUETOOTH is selected as the input source. The protection circuitry has been activated. (The D indicator on the top panel of the sound bar flashes.) Turn on the sound bar again. To stop the sound bar from turning off automatically, disable the auto power standby function (p.15). After confirming that all connections are made properly, turn on the sound bar again. If the power still turns off suddenly or cannot be turned on, unplug the power cable from the AC wall outlet and contact the nearest authorized Yamaha dealer or service center. Disable the Bluetooth standby mode (p.11). All indicators go out although the sound bar is turned on (it may seem that the sound bar is turned off). The sound bar is not responding correctly. The sound bar operates by itself. TV s 3D glasses do not work. The sound bar cannot be operated using the dedicated application HOME THEATER CONTROLLER. (The screen of the application does not shift from the demo mode.) The brightness of indicators is set to off on the DIMMER key setting. The internal microcomputer is frozen, due to an external electric shock (such as lightning or excessive static electricity) or to a drop in the power supply voltage. Another Bluetooth device is being operated nearby. The sound bar is blocking the 3D glasses transmitter of your TV. The Bluetooth device on which the application has been installed is not connected to the sound bar. Operate the DIMMER key to select the desired brightness (p.9). Hold down (power) on the rear panel of the sound bar for more than 10 seconds to reboot it. (If the problem persists, unplug the power cable from the AC wall outlet and plug it again.) Terminate Bluetooth connection of the sound bar (p.11). Check the position of the 3D glasses transmitter of your TV and adjust the position of the sound bar. Connect the Bluetooth device and the sound bar via Bluetooth and use the application. Bluetooth connection is terminated on a Bluetooth device when the Bluetooth standby mode is enabled. The protection circuitry has been activated three times consecutively. (If you try to turn on the power in this condition, the D indicator on the top panel of the sound bar flashes.) The power cannot be turned on. To protect the product, the power cannot be turned on. Unplug the power cable from the AC wall outlet and contact the nearest authorized Yamaha dealer or service center. 16 En

19 Audio Problem Cause Remedy No sound. Another input source is selected. Select an appropriate input source (p.8). The mute function is activated. Cancel the mute function (p.9). The volume is too low. Turn up the volume (p.8). No sound is coming from the subwoofer. The volume decreases when the sound bar is turned on. No surround effect. Noise is heard. The power cable of the sound bar is not connected properly. Input jacks on both devices are connected. Signals that the sound bar cannot play back are being input. The volume of the subwoofer is too low. The playback source does not contain low-frequency signals. The automatic volume adjustment function worked. To prevent excessive loudness, the sound bar automatically controls its volume within a certain level when the sound bar is turned on. Stereo playback is selected. The volume is too low. The TV or playback device is set to output 2 channel audio (such as PCM) only. The audio is output from the TV built-in speakers. The listening position is too close to the sound bar. The installation position selector switch is not set appropriately. The sound bar is too close to another digital or high-frequency device. Make sure that the power cable of the sound bar is connected to an AC wall outlet securely (p.6). Connect the input jack on the sound bar and the output jack on the external playback device. Change the digital audio output setting on the playback device to PCM or Dolby Digital. Turn up the volume of the subwoofer (p.8). Play back a sound source containing low-frequency signals, and confirm that the sound is output from the subwoofer. If necessary, turn up the volume (p.8). Select surround playback (p.9). Turn up the volume (p.8). Change the digital audio output setting on the TV or playback device to Dolby Digital or BitStream. Set the TV volume to minimum (p.6). Listen from a position at some distance from the sound bar. When placing the sound bar in front of a TV, set the installation position selector switch to T. When attaching the sound bar to a wall, set the installation position selector switch to W. Move those devices away from the sound bar. Remote control Problem Cause Remedy The sound bar cannot be controlled using the remote control. The TV cannot be controlled using the TV s remote control. The sound bar does not learn TV s remote control operations. Sound is coming from the TV when the sound bar volume is turned up with the TV s remote control. (when TV s remote control learning function is used) The sound bar is out of the operating range. The batteries are weak. The remote control sensor of the sound bar is exposed to direct sunlight or strong lighting. The remote control sensor of the TV is hidden by the sound bar. The TV s remote control key was not held down long enough. The TV s remote control does not use infrared signals. (Some remote controls may not work even if it uses infrared signals.) The position where you operated the TV s remote control is not appropriate. The batteries of the TV s remote control are weak. The remote control sensor of the sound bar is exposed to direct sunlight or strong lighting. The transmission of the remote control signal was disturbed by the TV screen light. Audio output is enabled on the TV. Use the remote control within the operating range (p.2). Replace with new batteries (p.2). Adjust the lighting angle, or reposition the sound bar. Adjust the installation position of the sound bar so that the remote control sensor of the TV is not hidden by the sound bar when operating the TV from the ordinary operation position. Hold down the key for more than 1 second twice or three times (p.12). The TV s remote control learning function cannot be used in this case. Use the sound bar s remote control to operate the sound bar. Operate the TV s remote control at the appropriate position (p.12). Replace with new batteries. Adjust the lighting angle, or reposition the sound bar. Turn off the TV and perform the learning operation again (p.12). Change the TV setting to disable the TV speaker output. If a setting to disable the speaker output is not available on your TV, try the following methods. - Connect headphones to the headphone jack on the TV. - Set the TV volume to minimum. En 17

20 The power of the sound bar and of the TV switch in the opposite direction. (For example, the TV is turned off if the sound bar is turned on.) (when TV s remote control learning function is used) Bluetooth The power of the TV was on when you performed the learning operation. Press the power key on the TV and (power) on the rear panel of the sound bar to turn them on and then press the power key on the TV s remote control to turn them off. Problem Cause Remedy Cannot make the sound bar pair Bluetooth is not selected as the input source. Select Bluetooth as the input source. with the The device does not support Perform pairing operations with a Bluetooth A2DP. device which supports A2DP. device. A Bluetooth adaptor, etc., that you want to pair with the sound bar has a password other than The sound bar and device are too far apart. There is a device (microwave oven, wireless LAN, etc.) that outputs signals in the 2.4 GHz frequency band nearby. Another Bluetooth device is connected. Use a Bluetooth adaptor, etc., whose password is Move the device closer to the sound bar. Move the sound bar away from the device that is emitting radio frequency signals. If the Bluetooth device is equipped with the wireless LAN function, turn off the wireless LAN function, and turn on the Bluetooth function only. Terminate current Bluetooth connection, and perform pairing with the new device. Cannot make a Bluetooth connection. Cannot make a Bluetooth connection (the BLUETOOTH indicator continues to flash rapidly). No sound is produced or the sound is interrupted during playback. Another Bluetooth device is connected. More than nine devices are paired and the oldest pairing information is deleted. There is a problem within the sound bar. The Bluetooth connection of the sound bar with the device is disconnected. Bluetooth is not selected as the input source. The sound bar and device are too far apart. There is a device (microwave oven, wireless LAN, etc.) that outputs signals in the 2.4 GHz frequency band nearby. The device is not set to send Bluetooth audio signals to the sound bar. Playback on the device has not been performed. The device s volume is set to minimum. The sound bar cannot make multiple Bluetooth connections. Terminate current Bluetooth connection, and make connection for the desired device. Perform pairing again. The sound bar can retain pairing information for up to eight devices. When pairing a ninth device, pairing data for the device with the oldest connection date will be deleted. Unplug the power cable from the AC wall outlet and contact the nearest authorized Yamaha dealer or service center. Perform Bluetooth connection operations again (p.10). Select Bluetooth as the input source. Move the device closer to the sound bar. Move the sound bar away from the device that is emitting radio frequency signals. If the Bluetooth device is equipped with the wireless LAN function, turn off the wireless LAN function, and turn on the Bluetooth function only. Change the audio output setting and connection setting on the device. Perform playback on the device. Turn up the device s volume level. 18 En

21 Specifications Item Amplifier Section Front L/R Section Tweeter Section Subwoofer Section Decoder Input Jacks Output Jack Maximum Rated Output Power Type Driver specifications Front L/R 30 W x 2 ch Subwoofer 60 W Acoustic suspension type 5.5 cm (2-1/8") cone non-magnetic shielding type x 2 Frequency Response 160Hz to 22kHz Impedance 6Ω Type Driver 19 mm (3/4") balanced dome magnetic shielding type x 2 Frequency Response 4kHz to 23kHz Impedance 4Ω Type Bass reflex type Driver 7.5 cm (3") cone non-magnetic shielding type x 2 Frequency Response 55Hz to 160Hz Impedance 3Ω Supported audio signal (TV, BD/DVD) Digital (Optical) Digital (Coaxial) Analog (3.5 mm stereo mini) Analog (RCA/monaural) PCM (2ch) Dolby Digital (up to 5.1ch) 1 (TV) 1 (BD/DVD) 1 (ANALOG) 1 (SUBWOOFER OUT) Bluetooth General Bluetooth version Ver EDR Supported protocols A2DP, SPP Supported codecs SBC, MPEG4 AAC Wireless output Bluetooth Class 2 Maximum communication 10 m ([33 ft] without obstructions) distance Supported content protection method SCMS-T U.S.A. and Canada models: AC 120 V, 60Hz Power Supply Taiwan model: AC V, 50/60Hz China model: AC 220V, 50Hz Other models: AC V, 50/60Hz Power Consumption 22 W Standby Power Consumption 0.4 W Bluetooth standby power consumption Dimensions (W x H x D) Weight * Specifications are subject to change without notice. 0.5 W (Taiwan, U.S.A., and Canada models) 0.6 W (China, and other models) 890 x 53 x 131 mm (installing the sound bar in front of a TV, etc.) (35" x 2-1/8" x 5-1/8") 890 x 131 x 59 mm (attaching the sound bar to a wall, with spacer) (35" x 5-1/8" x 2-3/8") 4.0 kg (8.8 lbs) En 19

22 PRECAUCIÓN: LEER ESTAS INDICACIONES ANTES DE UTILIZAR EL PRODUCTO. Para asegurar el mejor rendimiento de este aparato, lea atentamente este manual. Y luego guárdelo en un lugar seguro para poder consultarlo en el futuro en caso de ser necesario. Instale este sistema de sonido en un lugar bien ventilado, fresco, seco y limpio, alejado de la luz solar directa, fuentes de calor, vibraciones, polvo, humedad y/o frío. Para conseguir una ventilación adecuada, deje libres los siguientes espacios, como mínimo: Arriba: 10 cm, Atrás: 10 cm, A los lados: 10 cm Coloque este aparato lejos de otros aparatos eléctricos, motores o transformadores, para evitar así los ruidos de zumbido. No exponga este aparato a cambios bruscos de temperaturas, del frío al calor, ni lo coloque en lugares muy húmedos (una habitación con deshumidificador, por ejemplo), para impedir así que se forme condensación en su interior, lo que podría causar una descarga eléctrica, un incendio, daños en el aparato y/o lesiones a las personas. Evite instalar este aparato en un lugar donde puedan caerle encima objetos extraños y/o donde quede expuesto al goteo o a la salpicadura de líquidos. Encima de este aparato no ponga: Otros componentes, porque pueden causar daños y/o decoloración en la superficie de este aparato. Objetos con fuego (velas, por ejemplo), porque pueden causar un incendio, daños en el aparato y/o lesiones a las personas. Recipientes con líquidos, porque pueden caerse y derramar el líquido, causando descargas eléctricas al usuario y/o dañando el aparato. No tape este aparato con un periódico, mantel, cortina, etc. para no impedir el escape del calor. Si aumenta la temperatura en el interior del aparato, esto puede causar un incendio, daños en el aparato y/o lesiones a las personas. No enchufe este aparato a una toma de corriente hasta después de haber terminado todas las conexiones. No ponga el aparato al revés. Podría recalentarse y posiblemente causar daños. No utilice una fuerza excesiva con los conmutadores, los controles y/o los cables. Cuando desconecte el cable de alimentación de la toma de corriente, sujete la clavija y tire de ella; no tire del propio cable. No limpie este aparato con disolventes químicos porque podría estropear el acabado. Utilice un paño limpio y seco para limpiar el aparato. Utilice solamente la tensión especificada en este aparato. Utilizar el aparato con una tensión superior a la especificada resulta peligroso y puede producir un incendio, daños en el aparato y/o lesiones a las personas. Yamaha no se hará responsable de ningún daño debido al uso de este aparato con una tensión diferente de la especificada. Para impedir daños debidos a relámpagos, desconecte el cable de alimentación y antenas externas de la toma de corriente durante una tormenta eléctrica. No intente modificar ni arreglar este aparato. Póngase en contacto con el personal de servicio Yamaha cualificado cuando necesite realizar alguna reparación. La caja no deberá abrirse nunca por ninguna razón. Cuando no piense utilizar este aparato durante mucho tiempo (cuando se ausente de casa por vacaciones, por ejemplo) desconecte el cable de alimentación de la toma de corriente. Asegúrese de leer la sección Resolución de problemas antes de dar por concluido que su aparato está averiado. Antes de trasladar este aparato, pulse para ponerlo en el modo de espera, y luego desconecte el cable de alimentación de CA de la toma de corriente. La condensación se formará cuando cambie de repente la temperatura ambiental. Desconecte en este caso el cable de alimentación de la toma de corriente y no utilice el aparato. Instale este aparato cerca de la toma de CA y donde se pueda alcanzar fácilmente la clavija de alimentación. La colocación o la instalación seguras de la unidad es responsabilidad del propietario. Yamaha no se responsabilizará de ningún accidente provocado por la colocación o instalación incorrecta de los altavoces. Mantenga el producto lejos del alcance de los niños, para evitar la ingestión accidental de piezas pequeñas. Observaciones sobre los mandos a distancia y las pilas No derrame agua u otros líquidos en el mando a distancia. No deje caer el mando a distancia. No deje ni guarde el mando a distancia en uno de las siguientes lugares: lugares de humedad alta como, por ejemplo, cerca de un baño lugares con temperaturas elevadas, por ejemplo, cerca de una calefacción o estufa lugares con temperaturas demasiado bajas lugares polvorientos No exponga el sensor del mando a distancia de esta unidad a la luz solar directa ni a iluminación de focos fluorescentes invertidos. Si las pilas se agotan, el alcance operativo eficaz del mando a distancia se reduce considerablemente. Si esto sucediese, cambie las pilas por dos nuevas tan pronto como sea posible. No utilice pilas viejas y nuevas juntas. No utilice juntas pilas de tipos diferentes (alcalinas de manganeso, por ejemplo). Lea atentamente las instrucciones de la caja ya que hay distintos tipos de pilas con la misma forma y color. Las pilas gastadas pueden tener derrames. Si se produce algún derrame en las pilas, deséchelas inmediatamente. Evite tocar el líquido derramado o que entre en contacto con la ropa, etc. Ante de instalar pilas nuevas, limpie bien el compartimento de las pilas. No guarde las pilas en el bolsillo ni en un bolso junto con objetos metálicos, como monedas, etc. No arroje las pilas al cubo de la basura. Deséchelas de acuerdo con la normativa local aplicables. Mantenga las pilas alejadas de los niños. Si alguien tragase una pila accidentalmente, acuda a un médico de inmediato. Si no va a utilizar el mando a distancia durante mucho tiempo, quítele las pilas. No cargue ni desmonte las pilas suministradas. Las baterías no deberán exponerse a un calor excesivo como, por ejemplo, el que producen los rayos del sol, el fuego y similares. ADVERTENCIA PARA REDUCIR EL RIESGO DE INCENDIO O DESCARGA ELÉCTRICA, NO EXPONGA ESTE APARATO A LA LLUVIA NI A LA HUMEDAD. Aunque usted apague esta unidad con, esta unidad no se desconectará de la fuente de alimentación de CA mientras esté conectada a la toma de CA. En este estado, esta unidad ha sido diseñada para que consuma una cantidad de corriente muy pequeña. Tecla (encendido) Enciende la unidad o la ajusta en modo de espera. No utilice la unidad a menos de 22 cm de personas que tengan implantado un marcapasos o un desfribiliador. Las ondas de radio pueden afectar a los dispositivos médicos electrónicos. No utilice esta unidad cerca de dispositivos médicos o en el interior de instalaciones médicas. La placa de identificación está colocada en la parte inferior de la unidad. i Es