CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future

Size: px
Start display at page:

Download "CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future"

Transcription

1 LHV TV Surround System Owner s Manual Manual de Instrucciones

2 CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. Install this unit in a well ventilated, cool, dry, clean place - away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. For proper ventilation, allow the following minimum clearances (excludes a TV placed on top of this unit). Top: 5 cm (2 in), Rear: 5 cm (2 in), Sides: 5 cm (2 in) Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury. Avoid installing this unit where foreign objects may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: Other components, as they may cause damage and/or discoloration on the surface of this unit. Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury. Containers with liquid in them, as they may fall and liquid may cause electrical shock to the user and/or damage to this unit. Do not cover this unit with a newspaper, tablecloth, curtain, etc., in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury. Do not plug in this unit to a wall outlet until all connections are complete. Do not operate this unit upside-down. It may overheat, possibly causing damage. Do not use force on switches, knobs and/or cords. When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cable. Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. Yamaha will not be held responsible for any damage resulting from use of this unit with a voltage other than specified. To prevent damage by lightning, keep the power cable and outdoor antennas disconnected from a wall outlet or the unit during a lightning storm. Do not attempt to modify or fix this unit. Contact qualified Yamaha service personnel when any service is needed. The cabinet should never be opened for any reasons. When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet. Be sure to read the Troubleshooting section on common operating errors before concluding that this unit is faulty. Before moving this unit, press to set this unit in standby mode, and disconnect the power supply cable from the wall outlet. Condensation will form when the surrounding temperature changes suddenly. Disconnect the power supply cable from the outlet, then leave the unit alone. Install this unit near the wall outlet and where the AC power plug can be reached easily. The batteries shall not be exposed to excessive heat such as sunshine, fire or like. Secure placement or installation is the owner s responsibility. Yamaha shall not be liable for any accident caused by improper placement or installation of speakers. Notes on remote controls and batteries Do not spill water or other liquids on the remote control. Do not drop the remote control. Do not leave or store the remote control in the following places: places of high humidity, such as near a bath places of high temperatures, such as near a heater or a stove places of extremely low temperatures dusty places Do not expose the remote control sensor of this unit to direct sunlight or lighting such as inverted fluorescent lamps. If the batteries grow old, the effective operation range of the remote control decreases considerably. If this happens, replace the batteries with two new ones as soon as possible. Do not use old batteries together with new ones. Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color. Exhausted batteries may leak. If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. Do not carry batteries in a pocket or purse with metal objects like coins, etc. Do not throw away batteries with general house waste. Dispose of them correctly in accordance with your local regulations. Keep batteries away from children. If a battery is accidentally swallowed, contact your doctor immediately. When not planning to use the remote control for long periods of time, remove the batteries from the remote control. Do not charge or disassemble the supplied batteries. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by. In this state, this unit is designed to consume a very small quantity of power. (Power key) Turns on the power of this unit or sets it to the standby mode. Do not use this unit within 22 cm (9 inches) of persons with a heart pacemaker implant or defibrillator implant. Radio waves may affect electro-medical devices. Do not use this unit near medical devices or inside medical facilities. i En

3 Contents Supplied items...2 Features...3 Frequently asked questions...3 Part names and functions of the unit...4 Connections...5 Analog connection of an external device (game console)...6 Digital connection of an external device...6 Installations...7 Operations...8 Setting a surround sound effect for the installation position (SRT position) Selecting a surround sound effect of your choice Adjusting the volume level of each channel (CH LEVEL) Listening to the sound from a Bluetooth device Settings Programming the unit with the TV s remote control (TV s remote control learning function) Using an external subwoofer Making sound easy to listen at low volume Setting the auto power standby function Initializing the settings of the unit Troubleshooting Specifications About this manual This manual explains operations using the supplied remote control. Marks used in this manual NOTE This indicates precautions for use of the product and its feature limitations. HINT This indicates supplementary explanations for better use. En 1

4 Supplied items Make sure you have received all of the following items. How to use the remote control Preparing the remote control Peel off the protection sheet before use. Unit Remote control Battery x 2 (AAA, R03, UM4) Optical cable (1.5 m [4.9 ft]) Operating range of the remote control Remain within the operating range shown below. Within 6 m (20 ft) Owner s Manual (This manual) 2 En

5 Features Enjoy powerful and realistic sound from the unit. The unit is a home theater system which can be easily installed and connected to a TV and other devices. Digital sound projection Integrated multiple small speakers optimize the individual sound beams. The surround sound effect is enhanced by reflecting the beams onto the walls of the room (p.10). Surround mode Enjoy realistic surround sound. Select one of the five surround modes (movie, music, sports, game, TV program) for the source to be played back (p.10). Clear voice Make voice sound (such as dialogues and narrations) clear with just one touch (p.9). UniVolume Maintains consistent sound volume when inputs or sound sources switch (p.9). Frequently asked questions The following section covers popular functions and frequently asked questions about the unit. Q1 A1 Q2 A2 Q3 A3 What size TVs can I place on the unit? Flat screen TVs that weigh no more than 40 kg (88.1 lbs), have bases no wider than 750 mm (29-1/2") and no deeper than 340 mm (13-3/8"), and have screens no larger than 55 inches can be placed on the unit. Can I operate the unit using the remote control of the TV? Switching between the remote controls of the TV and unit is inconvenient. Yes. You can control the unit using your TV s remote control by the TV s remote control learning function (p.14). This function is available only for the IR (infrared) remote control. Check your TV s remote control type. Can I make voice sound more clearly? Yes. Dialogue in movies, TV news or sports programs, etc., can be made clearer using the clear voice function (p.9). Bluetooth connection Play back sound from a connected Bluetooth device (p.12). You can enjoy deep and fresh sound as close to the original by the Compressed Music Enhancer. This unit is also compliant with the aptx codec, which enables you to enjoy better sound from your smartphone. HOME THEATER CONTROLLER You can operate the unit easily by installing the dedicated controlling application HOME THEATER CONTROLLER. TV remote control learning function Operate the unit with the TV s remote control (p.14). En 3

6 Part names and functions of the unit Front panel Rear panel Overhead view A Indicators Indicate the status of the unit. The indicators will dim automatically if no operations are performed for 5 seconds. Refer to Operations (p.8 to 9) for the main functions of the indicators. B Remote control sensor Receives infrared signals from the remote control of the unit (p.2). C INPUT key Selects an input source to be played back (p.8). D MUTE key Mutes the audio output. Press the key again to unmute (p.8). E VOLUME (+/ ) keys Adjust the volume (p.8). F (power) key Turns on or off (standby) the unit (p.9). G Dual built-in subwoofers The built-in subwoofers are located in the bottom part of the unit. A SUBWOOFER OUT jack For connecting an external subwoofer with a monaural pin cable (p.16). B ANALOG input jacks For connecting an external device with an RCA stereo cable (p.6). C COAXIAL input jack For connecting an external device with a coaxial digital cable (p.6). D BD/DVD input jack For connecting a playback device, such as a Blu-ray Disc (BD) player, with an optical cable (p.5). E TV input jack For connecting a TV with an optical cable (p.5). HINT The unit may automatically turn off when the auto power standby function is enabled (p.17). 4 En

7 Connections Connect to a TV (or other peripheral device). Cautions Do not connect the power cable of the unit to the AC wall outlet before making connections. Do not use excessive force when inserting the cable plug. Doing so may damage the cable plug or terminal. 1 Remove the jack cover on the top panel of the unit. 2 Connect the TV and unit with the optical cable (supplied). Remove the cap of the optical cable and check the direction of the plug. To AC wall outlet Unit (rear) Overhead view Power cable Jack cover 3 Connect the power cable of the unit to an AC wall outlet. 4 Set the TV as follows. Set the TV volume to minimum. Disable the TV built-in speaker output (if available). 5 Attach the jack cover. HINT If a setting to disable the speaker output is not available on your TV, you may disable it by connecting headphones to the headphone jack on the TV. For details, refer to the manuals of the TV. The TV, BD/DVD and COAXIAL input jacks support the following audio signals. PCM (2ch) Dolby Digital (up to 5.1 channels) DTS Digital Surround (up to 5.1 channels) HINT In the following cases, connect the optical output of the playback device to the BD/DVD input of the unit with an optical cable (commercially available), then select the BD/DVD key on the remote control for the input source. The TV does not have an optical output. The TV does not output audio (or outputs low volume audio) from the connected playback device. The audio from the playback device connected to the TV cannot be heard as surround sound. OPTICAL OUTPUT Optical cable (commercially available) TV Optical cable Playback device (such as a BD player) Set top box OPTICAL OUTPUT HDMI cable (etc.) En 5

8 Analog connection of an external device (game console) You can connect an external device, such as a game console or TV that does not have an optical output, to the ANALOG input jacks of the unit. Digital connection of an external device You can connect an external device that has a coaxial digital audio output, such as a DVD player, to the COAXIAL input jack of the unit. Unit (rear) Overhead view RCA stereo cable (etc.) (commercially available) Unit (rear) Overhead view Coaxial digital cable (commercially available) Coaxial digital audio output (orange) Game console (etc.) NOTE Make sure the left (L) and right (R) channels are connected correctly. Select the ANALOG key on the remote control for the input source. NOTE Select the COAXIAL key on the remote control for the input source. 6 En

9 Installations Place the unit on a flat surface such as on top of a TV cabinet, and then place a TV on top of the unit. Obtaining effective surround sound effect To obtain effective surround sound effect, observe the following. Optimizing the surround sound effect for the installation position The unit achieves surround sound by reflecting sound beams off walls. The optimum surround sound effect is achieved by setting an SRT position according to the installation position of the unit. After turning on the unit, hold down the SRT POSITION key that corresponds to the installation position for more than 3 seconds. For details, refer to Setting a surround sound effect for the installation position (SRT position) (p.10). Cautions TVs that can be placed on the unit are flat-screen TVs that weigh no more than 40 kg (88.1 lbs), have bases no wider than 750 mm (29-1/2") and no deeper than 340 mm (13-3/8"), and have screens no larger than 55 inches. CRT TVs cannot be placed on the unit. Place the TV so that its base does not protrude from the unit s edges. If the TV base is too large to fit on top of the unit, place the unit in another location such as on an open shelf. In that case, make sure that the shelf is well-ventilated with enough clearance around the unit to prevent the heat from accumulating inside the unit. Place the unit so that it does not protrude from the TV cabinet s edges. Do not place any device other than a TV on the unit. If a device such as a BD player is placed on the unit, a malfunction due to vibrations may occur, or the TV installation may become unstable. Furthermore, if a hard object is placed on the unit, it may cause scratches on the unit. Never fix the unit to a wall or other surface using a fall prevention device, such as wire or bracket, supplied with the TV. Doing so may cause the unit fall together with the TV if an accident such as an earthquake occurs. Read the instruction manual of your TV carefully and fix the TV to a wall or sturdy object following the instruction. The unit contains non-magnetic shielding speakers. Do not place magnetically sensitive items (hard disk drive, etc.) near the unit. Determine the installation location considering the connection with external devices (such as a TV). Keep a distance of more than 2 meters (6.6 ft) between the unit and listener. Install the unit in front of the listening position. If the sound beams are blocked by obstacles such as furniture, adjust the position of the unit or the obstacles. Cautions Effective surround effect may not be achieved in the following environment. Sound beams are blocked by obstacles such as furniture. The room size is not within the following dimensions; Width: 3 meters to 7 meters (9.8 ft to 23 ft) Depth: 3 meters to 7 meters (9.8 ft to 23 ft) Height: 2 meters to 3.5 meters (6.6 ft to 11.5 ft) Listening position is too close to the unit. The unit is installed too close to the left or right wall. The unit is installed in the corner of the room. There is no wall for reflecting sound beam on the path of the sound beams. En 7

10 Operations Indicators The indicators on the front panel flash or light up, to indicate the operation and setting status. Input keys Select an input source to be played back. 1 The indicator for the selected input source lights up. (Example: when TV is selected) : Keys that require pressing for more than 3 seconds BLUETOOTH STANDBY, AUDIO DELAY, SRT POSITION (L, C, R), CH LEVEL, LEARN Remote control signal transmitter Transmits infrared signals. In this manual, illustrations of the nine in-line indicators are used for explanation. : Off : Lights up : Flashes (Example: When the STATUS indicator flashes and the TV indicator lights up) TV...TV audio BD/DVD...Audio from a device connected to the BD/DVD input jack COAXIAL...Audio from a device connected to the COAXIAL input jack ANALOG...Audio from a device connected to the ANALOG input jack BLUETOOTH...Audio from a Bluetooth connected device HINT To play audio of the playback device connected to the TV or to watch videos of the playback device, set the TV s input source to the playback device. For details on Bluetooth connection, refer to Listening to the sound from a Bluetooth device (p.12). SUBWOOFER keys (+/ ) Adjust the volume of the subwoofer. 2 Volume down ( ) Volume up (+) VOLUME keys (+/ ) Adjust the volume of the unit. Volume down ( ) Volume up (+) MUTE key Mutes the audio output. Press the key again to unmute. Flash (on mute) CH LEVEL key While you listen to the test-tone, you can adjust the volume level of each channel (p.11). 3 8 En

11 (power) key Turns on or off (standby) the unit. Green (turned on) Red (Bluetooth standby) (p.13) 4 CLEAR VOICE key Enables/disables the clear voice function. When this function is enabled, you can enjoy clear voice sounds while watching movies, TV dramas, news programs or sports programs. 7 SRT POSITION (SRT position) keys 8 For optimum surround sound effect, select a preset position mode according to where the unit is installed (p.10). Off (turned off) BLUETOOTH STANDBY key Enables/disables the Bluetooth standby mode (p.13). Surround mode / STEREO keys Choose from five different types of surround playback (surround mode keys), or stereo (2- channel) playback. When the surround playback is selected, the sound field program CINEMA DSP provides realistic surround effects (p.10). MOVIE / MUSIC / SPORTS / GAME / TV PROGRAM STEREO Lights up (surround playback) Off (stereo playback) HINT When 2-channel stereo signals are played in surround with Dolby Pro Logic II, the PLII indicator lights up. LEARN key Lights up (Dolby Pro Logic II) Sets the unit to the TV remote control learning mode (p.14). 5 6 Flash 3 times (enabled), flash once (disabled) UNIVOLUME key Enables/disables the UniVolume function. When this function is enabled, consistent volume is maintained when inputs or sound sources switch. Flash 3 times (enabled), flash once (disabled) AUDIO DELAY key Adjusts the audio delay to synchronize the sound with the video when the video image on the TV may seem delayed with respect to the sound. Follow the procedure below to adjust the audio delay. 1 Hold down the AUDIO DELAY key for more than 3 seconds. The left most indicator flashes. 2 Press the SUBWOOFER (+/ ) key to adjust the audio delay. Pressing the SUBWOOFER (+) key delays the audio output timing. ( ) (+) 3 To finish the adjustment, press the AUDIO DELAY key. HINT The adjustment will be finished automatically if no operations are performed for 20 seconds. Decoder indication The unit supports the following audio signals. You can check the type of the input audio signal by the color of the indicator. Green (Dolby Digital), Red (DTS Digital Surround) Off (PCM) En 9

12 Setting a surround sound effect for the installation position (SRT position) The surround sound is achieved by reflecting the sound beams off walls as shown in the illustration below. For optimum surround effect, turn on the unit and select the SRT POSITION key according to the installation position of the unit. 1 Hold down the SRT POSITION key that corresponds to the installation position of the unit for more than 3 seconds. The indicators on the front panel flash according to the set position. Left Center Selecting a surround sound effect of your choice Select the surround mode key to enjoy realistic surround effects that closely resemble a movie theater, the middle of a music concert, or a sports field event, by Yamaha s sound field program, CINEMA DSP. You can select a surround mode key that best suits the source from MOVIE, MUSIC, SPORTS, GAME, or TV PROGRAM. 1 Play back the source. 2 Press one of the surround mode keys (MOVIE, MUSIC, SPORTS, GAME, or TV PROGRAM). The SURROUND indicator on the front panel lights up. (Example: when MOVIE is selected) Right Lights up L (Left) C (Center) (default setting) Left side of room Center of room Surround mode The surround modes are described below. Select the surround mode that best suits the playback source and your personal taste. Sound field program Features MOVIE Creates a broad and expansive cinematic space. With Dolby or DTS surround effects, this program enriches your cinematic experience. MUSIC Creates the palpable excitement, as if you were standing at the front center of a live concert hall event. SPORTS Creates the realistic atmosphere of a live sports event or talk show. GAME Enjoy three-dimensional sound effects with computer or video games. TV PROGRAM Creates optimum surround sound for TV programs. R (Right) HINT When the source is a 2-channel stereo signal, the sound is played back as surround sound by the Dolby Pro Logic II technology. Right side of room 10 En

13 Adjusting the volume level of each channel (CH LEVEL) The surround effect is achieved using six channels (audio outputs) of the unit. While listening to a series of test-tones from the unit, you can adjust the volume level of each channel to balance the sound heard from your listening position. (Volume level adjustment of each channel is not available when the unit is in stereo playback mode.) 1 Hold down the CH LEVEL key on the remote control for more than 3 seconds. The STATUS indicator flashes in green during test-tone output. The test-tone cycles through the channels in the order below. The test-tone is output from each channel in turn for two seconds. You can confirm which channel is playing the testtone by the way the indicators flash. Test-tone flow 2 While the test-tone is output from the channel to be adjusted, press the SUBWOOFER key (+ or ) to balance the volume level with the other channels. During volume adjustment, the cycle of the test tone stops. When you have finished adjusting the current channel level, release the + or key and wait a moment for the test-tone cycle to resume. You can check the volume level by the indicator lights. 3 After adjustment is complete, press the CH LEVEL key again. The test-tone stops. HINT Press the VOLUME key (+ or ) to adjust the overall volume while the test-tone is being played back. When the SRT position setting is changed (p.10), the channel level setting will be overwritten. Front (left) Center Front (right) Surround (right) Surround (left) Subwoofer Back to beginning En 11

14 Listening to the sound from a Bluetooth device You can play back wirelessly from Bluetooth devices, such as smartphones or digital music players. See also the operating manual of the Bluetooth device for more details. Pairing a Bluetooth device with the unit When connecting to a Bluetooth device for the first time, pairing between the device and unit is required. Once pairing with a device is completed, subsequent connection with that device will not require pairing. 1 Press the BLUETOOTH key on the supplied remote control to select Bluetooth as the input source. The BLUETOOTH indicator on the front panel lights up in green. Bluetooth devices Lights up 2 Turn on the Bluetooth function of the device to be paired, and perform pairing. The operation varies depending on the device. Refer to the operation manual of the device. 3 Select SRT-1000 Yamaha in the Bluetooth device list on the device. If a passkey (PIN) is required, enter the number Perform the following steps to use a Bluetooth device with the unit. For the first Bluetooth connection For subsequent Bluetooth connection Pairing a Bluetooth device with the unit Playing back audio from a Bluetooth device on the unit NOTE When pairing is completed, or a completion message appears on the device. Perform pairing with the Bluetooth device and unit within 10 meters (33 ft) of each other. Up to eight Bluetooth devices can be paired with the unit. If a ninth device is paired, the oldest pairing information is deleted. If pairing information for a device is deleted, to use that device again, pairing of the device is required again. If a Bluetooth device is already connected to the unit, terminate that Bluetooth connection (p.13), then perform pairing with the new device. Refer to Bluetooth (p.20) in Troubleshooting if pairing cannot be achieved. 12 En

15 Playing back audio from a Bluetooth device on the unit 1 With the unit turned on, press the BLUETOOTH key on the supplied remote control to select Bluetooth as the input source. The BLUETOOTH indicator on the front panel lights up in green. Lights up 2 Turn on the Bluetooth function of the device. When Bluetooth connection is made correctly, the BLUETOOTH indicator of the unit flashes 3 times. Using the Bluetooth standby mode The Bluetooth standby mode allows you to turn on (or off) the unit automatically, that interlocked by the operation of the Bluetooth device. 1 With the unit turned on, hold down the BLUETOOTH STANDBY key for more than 3 seconds. Holding down the BLUETOOTH STANDBY key for 3 seconds each time toggles the mode between enabled and disabled. Flash 3 times (enabled), flash once (disabled) When the Bluetooth standby mode is enabled and the unit is turned off, the STATUS indicator lights up in red. (Bluetooth standby) Flashes 3 times 3 Play back a song on the device. Lights up (red) Functions available on Bluetooth devices with Bluetooth standby mode enabled Power on interlock function (when the unit is turned off) When Bluetooth connection is made on the device, the unit will turn on and will be ready to play back sound from the device. Power off interlock function (when the unit is turned on) The unit will be turned off when Bluetooth connection is terminated on a Bluetooth device. (Only when BLUETOOTH is selected as the input source.) NOTE Perform Bluetooth connection with the device and unit within 10 meters (33 ft) of each other. It may be necessary to select SRT-1000 Yamaha in the Bluetooth device list again, in the event that a connection problem occurs. You may have to change the output setting to output audio to the unit, depending on the Bluetooth device you are using. Adjust the volume level of the Bluetooth device as required. If a Bluetooth device is already connected to the unit, terminate that Bluetooth connection, then connect with the new device. Terminating Bluetooth connection Bluetooth connection is terminated in the following cases. When the unit is turned on and the Bluetooth connection is terminated, the BLUETOOTH indicator flashes once. Using the HOME THEATER CONTROLLER application By installing the dedicated free application HOME THEATER CONTROLLER to a Bluetooth device, such as a smartphone, you can perform various operations easily and conveniently with the Bluetooth device. (Setting items: basic operation, surround mode, sound adjustments) For details on HOME THEATER CONTROLLER, see the product information on our website. The Bluetooth function is turned off on the compatible device. The BLUETOOTH key is pressed for more than 3 seconds. The unit is turned off. En 13

16 Settings Programming the unit with the TV s remote control (TV s remote control learning function) Once you program the unit, you can control it with your TV s remote control for functions such as turning on/off the TV and unit simultaneously, or volume up/down and muting/ unmuting of the unit. 4-2 While pointing your TV s remote control at the remote control sensor, hold down the mute key for more than 1 second twice or three times. Approx. 30 cm (1 ft) TV s remote control This function is available only when your TV s remote control uses IR (infrared) signal. An RF (Radio Frequency) remote control will not work. If you want to use a cable or satellite set top box s remote control to operate the unit, use your original TV s IR (infrared) remote control to program the unit, then use the set top box s remote control to operate. If by changing the volume of the unit the TV s volume also changes, set the TV s volume to minimum, or disable speaker output. Hold down (more than 1 second) Release (more than 1 second) Hold down (more than 1 second) Release (...) 1 Turn off the TV. 2 Turn off the unit. 3 Hold down the LEARN key on the unit s remote control for more than 3 seconds to set the unit to the learning mode. When the unit is in the learning mode, the indicators on the front panel flash as shown below. Result Bleep/buzzer Indicators Successfully learned Failed to learn * Repeat from Step 4-1. Once Twice 5 Teach the unit the Volume ( ) code of the TV s remote control. 5-1 Press VOLUME ( ) on the front panel of the unit. Lights up Flash NOTE Steps 4 to 7 require only the TV s remote control and the keys on the front panel of the unit. The remote control of the unit is not necessary. If the unit has already learned functions, the following indicators light up. Mute: BD/DVD, Volume (-): COAXIAL, Volume (+): ANALOG, Power: BLUETOOTH 4 Teach the unit the Mute code of the TV s remote control. 4-1 Press MUTE on the front panel of the unit. 5-2 While pointing your TV s remote control at the remote control sensor, hold down the volume ( ) key for more than 1 second twice or three times. Result Bleep/buzzer Indicators Successfully learned Once Lights up Failed to learn * Repeat from Step 5-1. Twice Flash 14 En

17 6 Teach the unit the Volume (+) code of the TV s remote control. 6-1 Press VOLUME (+) on the front panel of the unit. 6-2 While pointing your TV s remote control at the remote control sensor, hold down the volume (+) key for more than 1 second twice or three times. Result Bleep/buzzer Indicators Clearing all learned operations 1 With the unit turned off, hold down the LEARN key on the supplied remote control for more than 3 seconds (for entering the learning mode). When the unit is in the learning mode, the indicators on the front panel flash as shown below. Successfully learned Once Lights up Failed to learn * Repeat from Step 6-1. Twice 7 Teach the unit the Power code of the TV s remote control. 7-1 Press (power) on the front panel of the unit. 7-2 While pointing your TV s remote control at the remote control sensor, hold down the power key for more than 1 second twice or three times. Result Bleep/buzzer Indicators Flash 2 Hold down INPUT on the front panel of the unit for more than 3 seconds. If the clearing is completed, you will hear the bleep sound three times. 3 Press the LEARN key on the supplied remote control. Flashes in red (cleared) Successfully learned Once Lights up Failed to learn * Repeat from Step 7-1. Twice Flash 8 To finish the learning mode, press the LEARN key on the unit s remote control. This completes the necessary settings. Now you can operate the unit with the TV s remote control s mute key, volume keys, or power key. HINT The learning mode will be finished automatically if no operations are performed for 5 minutes. Set the TV volume to minimum. When you turn up the volume of the unit with the TV s remote control, the volume of the TV may be turned up at the same time. In this case, follow Step 4 in Connections (p.5) to change the TV setting. You can press the (power) key on the unit s remote control to finish learning mode. En 15

18 Using an external subwoofer The unit has dual built-in subwoofers; however you can connect an external subwoofer when you want to enhance low frequency sound. Connect a subwoofer to the SUBWOOFER OUT jack of the unit. Making sound easy to listen at low volume You can change the dynamic range to make sounds easy to hear at a low volume. 1 Turn off the unit. 2 Hold down the key for the desired mode for more than 5 seconds. Unit (rear) Overhead view Pin cable for subwoofer (commercially available) The unit turns on with the selected setting. Returns to Normal Sets to Standard Sets to Maximum Three settings are available (see below). You can confirm the setting status by the lights of the indicator, when the unit is turned on. Setting Description Indicator Normal Automatically adjusts the dynamic range based on the volume level of the source. Lights up in green Mono input Standard Compresses the dynamic range to suit a living room environment, etc. Lights up in orange NOTE Maximum Does not compress the dynamic range. Use an external subwoofer with built-in amplifier. Lights up in red NOTE Normal is set as default. 16 En

19 Setting the auto power standby function By enabling the auto power standby function, you can avoid forgetting to turn off the unit after use, or if you fall asleep while watching TV. NOTE When the auto power standby function is enabled and one of the following conditions is met, the unit will automatically turn off. No operation for 8 hours No audio input and no operations for 20 minutes when BLUETOOTH is selected as the input source. 1 With the unit turned off, hold down the MUTE key on the unit s remote control for more than 5 seconds to enable/disable the auto power standby function. You can check the status of the auto power standby function with the BD/DVD indicator when turning on the unit. Initializing the settings of the unit Follow the procedure below to initialize the unit. 1 Turn off the unit. 2 Hold down (power) on the front panel of the unit for more than 3 seconds. Flash (initialized) Off (enabled), lights up (disabled) HINT Initial setting varies depending on the country or region. U.K. and Europe models: enabled Other models: disabled En 17

20 Troubleshooting Refer to the table below when the unit does not function properly. If the problem you are experiencing is not listed below or if the instructions below do not help, turn off the unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. First, check the following: A The power cables of the unit, TV and playback devices (such as BD players) are connected to AC wall outlets securely. B The unit, TV and playback devices (such as BD players) are turned on. C The connectors of each cable are securely inserted in to jacks on each device. Power and system Problem Cause Remedy The power turns off suddenly. The auto power standby function worked. When the auto power standby function is enabled and one of the following conditions is met, the unit will automatically turn off. - No operation for 8 hours - No audio input and no operations for 20 minutes when BLUETOOTH is selected as the input source. The internal microcomputer is frozen, due to an external electric shock (such as lightning or excessive static electricity) or to a drop in the power supply voltage. The protection circuitry has been activated. (The STATUS indicator on the front panel of the unit flashes.) Bluetooth connection is terminated on a Bluetooth device when the Bluetooth standby mode is enabled. Turn on the unit again. To stop the unit from turning off automatically, disable the auto power standby function (p.17). Hold down (power) on the front panel of the unit for more than 10 seconds to reboot it. (If the problem persists, disconnect the power cable from the AC wall outlet and plug it again.) After confirming that all connections are made properly, turn on the unit again. If the power often suddenly turns off, unplug the power cable from the AC wall outlet and contact the nearest authorized Yamaha dealer or service center. Disable the Bluetooth standby mode (p.13). The power cannot be turned on. The unit is not responding correctly. The unit operates by itself. Audio The protection circuitry has been activated three times consecutively. (If you try to turn on the power in this condition, the STATUS indicator flashes.) The internal microcomputer is frozen, due to an external electric shock (such as lightning or excessive static electricity) or to a drop in the power supply voltage. Another Bluetooth device is being operated nearby. To protect the product, the power cannot be turned on. Unplug the power cable from the AC wall outlet and contact the nearest authorized Yamaha dealer or service center. Hold down (power) on the front panel of the unit for more than 10 seconds to reboot it. (If the problem persists, disconnect the power cable from the AC wall outlet and plug it again.) Terminate Bluetooth connection of the unit and connect the unit and device again (p.13). Problem Cause Remedy No sound. Another input source is selected. Select an appropriate input source (p.8). The mute function is activated. Cancel the mute function (p.8). The volume is too low. Turn up the volume (p.8). No sound is coming from the subwoofer. The volume decreases when the unit is turned on. The volume of the subwoofer is too low. The playback source does not contain low-frequency signals. The automatic volume adjustment function worked. To prevent excessive loudness, the unit automatically controls its volume within a certain level when the unit is turned on. Turn up the volume of the subwoofer (p.8). -- If necessary, turn up the volume (p.8). 18 En

21 No surround effect. Noise is heard. Remote control Stereo playback is selected. The volume is too low. The volume of the surround left and right channels is low. The TV or playback device is set to output 2-channel audio (such as PCM) only. The correct SRT position mode is not selected. Sound beams are not reflected effectively off walls because of the shape of the room, etc. The unit is too close to another digital or high-frequency device. Problem Cause Remedy Select the surround mode key to change for surround playback (p.10). Turn up the volume (p.8). Turn up the volume of the surround left and right channels (p.11). Change the digital audio output setting on the TV or playback device. Select a SRT POSITION key on the remote control which is best suited for your listening environment. Use of the sound reflection board (sold separately) is recommended (p.21). Move those devices away from the unit. Sound is coming from the TV when the unit volume is turned up with the TV remote control. (when TV remote control learning function is used) The power of the unit and of the TV switch in the opposite direction. (For example, the TV is turned off if the unit is turned on.) (when TV remote control learning function is used) Audio output is enabled on the TV. The power of the TV was on when you performed the learning operation. Change the TV setting to disable the TV speaker output. If a setting to disable the speaker output is not available on your TV, try the following methods. - Connect headphones to the headphone jack on the TV. - Set the TV volume to minimum. Press the power key on the TV and (power) on the front panel of the unit to turn them on and then press the power key on the TV remote control to turn them off. The unit cannot be controlled using the remote control. The unit is out of the operating range. The batteries are weak. The remote control sensor of the unit is exposed to direct sunlight or strong lighting. The TV remote control key was not held down long enough. The TV remote control does not use infrared signals. (Some remote controls may not work even if it uses infrared signals.) The position where you operated the TV remote control is not appropriate. The batteries of the TV remote control are weak. The remote control sensor of the unit is exposed to direct sunlight or strong lighting. The transmission of the remote control signal was disturbed by the TV screen light. Use the remote control within the operating range (p.2). Replace with new batteries (p.2). Adjust the lighting angle, or reposition the unit. The unit does not learn TV remote control operations. Hold down the key for more than 1 second twice or three times (p.14). The TV remote control learning function cannot be used in this case. Use the supplied remote control to operate the unit. Operate the TV remote control at the appropriate position (p.14). Replace with new batteries. Adjust the lighting angle, or reposition the unit. Turn off the TV and perform the learning operation again (p.14). En 19

22 Bluetooth Problem Cause Remedy Cannot make the unit paired with Bluetooth is not selected as the input source. Select Bluetooth as the input source. the Bluetooth A Bluetooth adaptor, etc., that you Use a Bluetooth adaptor, etc., whose device. want to pair with the unit has a password is password other than The unit and device are too far Move the device closer to the unit. apart. Cannot make a Bluetooth connection. No sound is produced or the sound is interrupted during playback. There is a device (microwave oven, wireless LAN, etc.) outputs signals in the 2.4 GHz frequency band nearby. Another Bluetooth device is connected. Another Bluetooth device is connected. More than nine devices are paired and the oldest pairing information is deleted. The Bluetooth connection of the unit with the device is disconnected. Bluetooth is not selected as the input source. The unit and device are too far apart. There is a device (microwave oven, wireless LAN, etc.) outputs signals in the 2.4 GHz frequency band nearby. The device is not set to send Bluetooth audio signals to the unit. Playback on the device has not been performed. The device s volume is set to minimum. Move this unit away from the device that is emitting radio frequency signals. Terminate current Bluetooth connection, and perform pairing with the new device. The unit cannot make multiple Bluetooth connections. Terminate current Bluetooth connection, and make connection for the desired device. Perform pairing again. The unit can retain pairing information for up to eight devices. When pairing a ninth device, the oldest pairing information will be deleted. Perform Bluetooth connection operations again (p.13). Select Bluetooth as the input source. Move the device closer to the unit. Move this unit away from the device that is emitting radio frequency signals. Change the audio output setting and connection setting on the device. Perform playback on the device. Turn up the volume level. 20 En

23 When surround effect is not enough The unit achieves its surround sound effects by projecting sound beams which reflect off walls. The sound beams are not reflected toward to the listening position caused by furniture, etc., in the path of sound beams, or the room shape. In this case, the sound may become unbalanced. How to install YRB-100 The unit outputs sound beams according to the SRT position settings (p.9) as shown in the following illustrations. Install the YRB-100 in the path of the sound beam. shows the recommended install position. FL: Front left FR: Front right SL: Surround left SR: Surround right Figure 1. Ideal condition Sound beams are reflected correctly and surround sound effects are balanced. Figure 2. Surround (right) beam is not being reflected because there is no wall. Surround (right) is quieter than surround (left), or surround (right) is in front of its proper location. SRT position: Center If the sound beams are not reflected toward to the listening position (figure 2), you can adjust for this by installing the optional sound reflection board (YRB-100). SRT position: Left SRT position: Right NOTE YRB-100 may not be available depending on the country or region. YRB-100 Figure 3. With a sound reflection board installed The sound beam for surround (right) is reflected correctly, and correct surround sound effect is achieved. After installing the sound reflection board, refer to the YRB-100 owner s manual to adjust the height and angle. It is recommended to use the test-tone (by holding down the CH LEVEL key) when adjusting the board (p.11). By installing the board close to your listening position, you can achieve clear surround sound positioning. NOTE This unit does not have the function to automatically adjust sound beam angles. It is not necessary to adjust the sound beam angles, although the procedure is described in the owner s manual. En 21

24 Specifications Item Amplifier Array speakers Woofer Subwoofer Decoder Input Jacks Output Jack Maximum Rated Output Power Type Driver Frequency Response Impedance Type Driver TV Surround System (SRT-1000) Array speakers 2 W x 8 Woofer 30 W x 2 Subwoofer 60 W Acoustic suspension type Full range 2.8 cm (1-1/8") cone magnetic shielding type x Hz to 22 khz 4 Ω Acoustic suspension type Full range 4 x 10 cm (1-1/2 x 4") cone non-magnetic shielding type x 2 Frequency Response 150 Hz to 22 khz Impedance 6 Ω Type Bass reflex type Driver 8.5 cm (3-1/4") cone non-magnetic shielding type x 2 Frequency Response 45 Hz to 150 Hz Impedance 6 Ω Supported audio signal (TV, BD/ DVD) Digital (Optical) Digital (Coaxial) Analog (RCA/stereo) Analog (RCA/monaural) PCM (2ch) Dolby Digital DTS Digital Surround 2 (TV, BD/DVD) 1 (COAXIAL) 1 (ANALOG) 1 (SUBWOOFER OUT) Bluetooth General * Specifications are subject to change without notice. The Bluetooth Ver EDR version Supported A2DP protocols Supported SBC, aptx codecs Wireless output Bluetooth Class 2 Maximum communication 10 m ([33 ft] without obstructions) distance Supported content SCMS-T protection method U.S.A. and Canada models: AC 120 V, 60 Hz Power Supply Taiwan model: AC V, 50/60 Hz Other models: AC V, 50/60 Hz Power 24 W Consumption Standby Power Consumption Dimensions (W x H x D) Weight logo and Cinema DSP are registered trademarks of Yamaha Corporation. UniVolume is a trademark of Yamaha Corporation. 0.3 W (When Bluetooth Standby is enabled) 0.2 W (When Bluetooth Standby is disabled) 780 x 77 x 370 mm (30-3/4" x 3" x 14-5/8") 8.8 kg (19.4 lbs) Bluetooth is a registered trademark of the Bluetooth SIG and is used by Yamaha in accordance with a license agreement. Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double-d symbol are trademarks of Dolby Laboratories. 22 En

25 For DTS patents, see Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks, and DTS Digital Surround is a trademark of DTS, Inc. DTS, Inc. All Rights Reserved CSR plc and its group companies. The aptx mark and the aptx logo are trade marks of CSR plc or one of its group companies and may be registered in one or more jurisdictions. Blu-ray Disc, Blu-ray, and the logos are trademarks of the Blu-ray Disc Association. Bluetooth Bluetooth is a technology for wireless communication between devices within an area of about 10 meters (33 ft) employing the 2.4 GHz frequency band, a band which can be used without a license. Handling Bluetooth communications The 2.4 GHz band used by Bluetooth compatible devices is a radio band shared by many types of equipment. While Bluetooth compatible devices use a technology minimizing the influence of other components using the same radio band, such influence may reduce the speed or distance of communications and in some cases interrupt communications. The speed of signal transfer and the distance at which communications is possible differs according to the distance between the communicating devices, the presence of obstacles, radio wave conditions and type of equipment. Yamaha does not guarantee all wireless connections between this unit and devices compatible with Bluetooth function. En 23

26 PRECAUCIÓN: LEER ESTAS INDICACIONES ANTES DE UTILIZAR EL PRODUCTO. Para asegurar el mejor rendimiento de este aparato, lea atentamente este manual. Y luego guárdelo en un lugar seguro para poder consultarlo en el futuro en caso de ser necesario. Instale este sistema de sonido en un lugar bien ventilado, fresco, seco y limpio, alejado de la luz solar directa, fuentes de calor, vibraciones, polvo, humedad y/o frío. Para conseguir una ventilación adecuada, deje libres los siguientes espacios, como mínimo (no incluye un televisor colocado encima de esta unidad): Arriba: 5 cm, Atrás: 5 cm, A los lados: 5 cm Coloque este aparato lejos de otros aparatos eléctricos, motores o transformadores, para evitar así los ruidos de zumbido. No exponga este aparato a cambios bruscos de temperaturas, del frío al calor, ni lo coloque en lugares muy húmedos (una habitación con deshumidificador, por ejemplo), para impedir así que se forme condensación en su interior, lo que podría causar una descarga eléctrica, un incendio, daños en el aparato y/o lesiones a las personas. Evite instalar este aparato en un lugar donde puedan caerle encima objetos extraños y/o donde quede expuesto al goteo o a la salpicadura de líquidos. Encima de este aparato no ponga: Otros componentes, porque pueden causar daños y/o decoloración en la superficie de este aparato. Objetos con fuego (velas, por ejemplo), porque pueden causar un incendio, daños en el aparato y/o lesiones a las personas. Recipientes con líquidos, porque pueden caerse y derramar el líquido, causando descargas eléctricas al usuario y/o dañando el aparato. No tape este aparato con un periódico, mantel, cortina, etc. para no impedir el escape del calor. Si aumenta la temperatura en el interior del aparato, esto puede causar un incendio, daños en el aparato y/o lesiones a las personas. No enchufe este aparato a una toma de corriente hasta después de haber terminado todas las conexiones. No ponga el aparato al revés. Podría recalentarse y posiblemente causar daños. No utilice una fuerza excesiva con los conmutadores, los controles y/o los cables. Cuando desconecte el cable de alimentación de la toma de corriente, sujete la clavija y tire de ella; no tire del propio cable. No limpie este aparato con disolventes químicos porque podría estropear el acabado. Utilice un paño limpio y seco para limpiar el aparato. Utilice solamente la tensión especificada en este aparato. Utilizar el aparato con una tensión superior a la especificada resulta peligroso y puede producir un incendio, daños en el aparato y/o lesiones a las personas. Yamaha no se hará responsable de ningún daño debido al uso de este aparato con una tensión diferente de la especificada. Para impedir daños debidos a relámpagos, desconecte el cable de alimentación y antenas externas de la toma de corriente durante una tormenta eléctrica. No intente modificar ni arreglar este aparato. Póngase en contacto con el personal de servicio Yamaha cualificado cuando necesite realizar alguna reparación. La caja no deberá abrirse nunca por ninguna razón. Cuando no piense utilizar este aparato durante mucho tiempo (cuando se ausente de casa por vacaciones, por ejemplo) desconecte el cable de alimentación de la toma de corriente. Asegúrese de leer la sección Resolución de problemas antes de dar por concluido que su aparato está averiado. Antes de trasladar este aparato, pulse para ponerlo en el modo de espera, y luego desconecte el cable de alimentación de CA de la toma de corriente. La condensación se formará cuando cambie de repente la temperatura ambiental. Desconecte en este caso el cable de alimentación de la toma de corriente y no utilice el aparato. Instale este aparato cerca de la toma de CA y donde se pueda alcanzar fácilmente la clavija de alimentación. Las baterías no deberán exponerse a un calor excesivo como, por ejemplo, el que producen los rayos del sol, el fuego y similares. La colocación o la instalación seguras de la unidad es responsabilidad del propietario. Yamaha no se responsabilizará de ningún accidente provocado por la colocación o instalación incorrecta de los altavoces. Observaciones sobre los mandos a distancia y las pilas No derrame agua u otros líquidos en el mando a distancia. No deje caer el mando a distancia. No deje ni guarde el mando a distancia en uno de las siguientes lugares: lugares de humedad alta como, por ejemplo, cerca de un baño lugares con temperaturas elevadas, por ejemplo, cerca de una calefacción o estufa lugares con temperaturas demasiado bajas lugares polvorientos No exponga el sensor del mando a distancia de esta unidad a la luz solar directa ni a iluminación de focos fluorescentes invertidos. Si las pilas se agotan, el alcance operativo eficaz del mando a distancia se reduce considerablemente. Si esto sucediese, cambie las pilas por dos nuevas tan pronto como sea posible. No utilice pilas viejas y nuevas juntas. No utilice juntas pilas de tipos diferentes (alcalinas de manganeso, por ejemplo). Lea atentamente las instrucciones de la caja ya que hay distintos tipos de pilas con la misma forma y color. Las pilas gastadas pueden tener derrames. Si se produce algún derrame en las pilas, deséchelas inmediatamente. Evite tocar el líquido derramado o que entre en contacto con la ropa, etc. Ante de instalar pilas nuevas, limpie bien el compartimento de las pilas. No guarde las pilas en el bolsillo ni en un bolso junto con objetos metálicos, como monedas, etc. No arroje las pilas al cubo de la basura. Deséchelas de acuerdo con la normativa local aplicables. Mantenga las pilas alejadas de los niños. Si alguien tragase una pila accidentalmente, acuda a un médico de inmediato. Si no va a utilizar el mando a distancia durante mucho tiempo, quítele las pilas. No cargue ni desmonte las pilas suministradas. ADVERTENCIA PARA REDUCIR EL RIESGO DE INCENDIO O DESCARGA ELÉCTRICA, NO EXPONGA ESTE APARATO A LA LLUVIA NI A LA HUMEDAD. Aunque usted apague esta unidad con, esta unidad no se desconectará de la fuente de alimentación de CA mientras esté conectada a la toma de CA. En este estado, esta unidad ha sido diseñada para que consuma una cantidad de corriente muy pequeña. (Tecla de encendido) Enciende la unidad o la ajusta en modo de espera. No utilice la unidad a menos de 22 cm de personas que tengan implantado un marcapasos o un desfribiliador. Las ondas de radio pueden afectar a los dispositivos médicos electrónicos. No utilice esta unidad cerca de dispositivos médicos o en el interior de instalaciones médicas. i Es

TX-NR3030_BAS_Cs_ indd

TX-NR3030_BAS_Cs_ indd TX-NR3030 http://www.onkyo.com/manual/txnr3030/adv/cs.html Cs 1 2 3 Speaker Cable 2 HDMI OUT HDMI IN HDMI OUT HDMI OUT HDMI OUT HDMI OUT 1 DIGITAL OPTICAL OUT AUDIO OUT TV 3 1 5 4 6 1 2 3 3 2 2 4 3 2 5

More information

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future LV Front Surround System Owner s Manual Manual de Instrucciones CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully. Keep it in a safe place

More information

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future LV Front Surround System (YAS-CU203+NS-WSW41) Owner s Manual Manual de Instrucciones CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully.

More information

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future TL TV Surround System Owner s Manual Manual de Instrucciones CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully. Keep it in a safe place

More information

OA-253_H1~H4_OL.ai

OA-253_H1~H4_OL.ai WARNINGS Note: Read ALL the following BEFORE using this product. Follow all Guidelines at all times while using this product. CAUTION This warning indicates possibility of personal injury and material

More information

Logitech Wireless Combo MK45 English

Logitech Wireless Combo MK45 English Logitech Wireless Combo MK45 Setup Guide Logitech Wireless Combo MK45 English................................................................................... 7..........................................

More information

LH_Series_Rev2014.pdf

LH_Series_Rev2014.pdf REMINDERS Product information in this catalog is as of October 2013. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check

More information

K301Q-D VRT中英文说明书141009

K301Q-D VRT中英文说明书141009 THE INSTALLING INSTRUCTION FOR CONCEALED TANK Important instuction:.. Please confirm the structure and shape before installing the toilet bowl. Meanwhile measure the exact size H between outfall and infall

More information

BC04 Module_antenna__ doc

BC04 Module_antenna__ doc http://www.infobluetooth.com TEL:+86-23-68798999 Fax: +86-23-68889515 Page 1 of 10 http://www.infobluetooth.com TEL:+86-23-68798999 Fax: +86-23-68889515 Page 2 of 10 http://www.infobluetooth.com TEL:+86-23-68798999

More information

01CP-WX3030WNetc_CO_ENG.indd

01CP-WX3030WNetc_CO_ENG.indd Data Video Projector User s Manual (Concise) ModelS: 8928A/8930A/8931WA/ 8933W Information in this Guide may change due to product improvements. To obtain the latest manuals, literature, and software please

More information

1.ai

1.ai HDMI camera ARTRAY CO,. LTD Introduction Thank you for purchasing the ARTCAM HDMI camera series. This manual shows the direction how to use the viewer software. Please refer other instructions or contact

More information

CANVIO_AEROCAST_CS_EN.indd

CANVIO_AEROCAST_CS_EN.indd 简 体 中 文...2 English...4 SC5151-A0 简 体 中 文 步 骤 2: 了 解 您 的 CANVIO AeroCast CANVIO AeroCast 无 线 移 动 硬 盘 快 速 入 门 指 南 欢 迎 并 感 谢 您 选 择 TOSHIBA 产 品 有 关 您 的 TOSHIBA 产 品 的 详 情, 请 参 阅 包 含 更 多 信 息 的 用 户 手 册 () 安

More information

KDC-U5049 KDC-U4049 Made for ipod, and Made for iphone mean that an electronic accessory has been designed to connect specifically to ipod, or iphone,

KDC-U5049 KDC-U4049 Made for ipod, and Made for iphone mean that an electronic accessory has been designed to connect specifically to ipod, or iphone, KDC-U5049 KDC-U4049 Made for ipod, and Made for iphone mean that an electronic accessory has been designed to connect specifically to ipod, or iphone, respectively, and has been certified by the developer

More information

<4D6963726F736F667420576F7264202D2032303130C4EAC0EDB9A4C0E04142BCB6D4C4B6C1C5D0B6CFC0FDCCE2BEABD1A15F325F2E646F63>

<4D6963726F736F667420576F7264202D2032303130C4EAC0EDB9A4C0E04142BCB6D4C4B6C1C5D0B6CFC0FDCCE2BEABD1A15F325F2E646F63> 2010 年 理 工 类 AB 级 阅 读 判 断 例 题 精 选 (2) Computer mouse How does the mouse work? We have to start at the bottom, so think upside down for now. It all starts with mouse ball. As the mouse ball in the bottom

More information

1 2 3 Speaker Cable 2

1 2 3 Speaker Cable   2 TX-NR636 AV RECEIVER http://www.onkyo.com/manual/txnr636upg/adv/ct.html Ct 1 2 3 Speaker Cable http://www.onkyo.com/manual/txnr636upg/adv/ct.html 2 HDMI OUT HDMI IN HDMI OUT HDMI OUT HDMI OUT HDMI OUT

More information

Mixcder ShareMe 7 User Manual

Mixcder ShareMe 7 User Manual User s Manual MODEL:ShareMe7 Wireless Headphone Important safety instruction If used in the correct method, this design and production of this product can ensure your personal safety completely. However,

More information

Microsoft Word - ChineseSATII .doc

Microsoft Word - ChineseSATII .doc 中 文 SAT II 冯 瑶 一 什 么 是 SAT II 中 文 (SAT Subject Test in Chinese with Listening)? SAT Subject Test 是 美 国 大 学 理 事 会 (College Board) 为 美 国 高 中 生 举 办 的 全 国 性 专 科 标 准 测 试 考 生 的 成 绩 是 美 国 大 学 录 取 新 生 的 重 要 依

More information

pdf

pdf THE INSTLLING INSTRUCTION FOR CONCELED TNK Important instuction:.. Please confirm the structure and shape before installing the toilet bowl. Meanwhile measure the exact size H between outfall and infall

More information

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DV-SP302 Ct WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE

More information

Microsoft Word - template.doc

Microsoft Word - template.doc HGC efax Service User Guide I. Getting Started Page 1 II. Fax Forward Page 2 4 III. Web Viewing Page 5 7 IV. General Management Page 8 12 V. Help Desk Page 13 VI. Logout Page 13 Page 0 I. Getting Started

More information

國 立 政 治 大 學 教 育 學 系 2016 新 生 入 學 手 冊 目 錄 表 11 國 立 政 治 大 學 教 育 學 系 博 士 班 資 格 考 試 抵 免 申 請 表... 46 論 文 題 目 申 報 暨 指 導 教 授... 47 表 12 國 立 政 治 大 學 碩 博 士 班 論

國 立 政 治 大 學 教 育 學 系 2016 新 生 入 學 手 冊 目 錄 表 11 國 立 政 治 大 學 教 育 學 系 博 士 班 資 格 考 試 抵 免 申 請 表... 46 論 文 題 目 申 報 暨 指 導 教 授... 47 表 12 國 立 政 治 大 學 碩 博 士 班 論 國 立 政 治 大 學 教 育 學 系 2016 新 生 入 學 手 冊 目 錄 一 教 育 學 系 簡 介... 1 ( 一 ) 成 立 時 間... 1 ( 二 ) 教 育 目 標 與 發 展 方 向... 1 ( 三 ) 授 課 師 資... 2 ( 四 ) 行 政 人 員... 3 ( 五 ) 核 心 能 力 與 課 程 規 劃... 3 ( 六 ) 空 間 環 境... 12 ( 七 )

More information

HWS-BTA2W

HWS-BTA2W 2-689-456-81(1) Bluetooth Wireless Audio Adapter (Transmitter / Receiver) Operating Instructions GB CT HWS-BTA2W 2007 Sony Corporation WARNING To reduce the risk of fire or electric shock, do not expose

More information

Important Notice SUNPLUS TECHNOLOGY CO. reserves the right to change this documentation without prior notice. Information provided by SUNPLUS TECHNOLO

Important Notice SUNPLUS TECHNOLOGY CO. reserves the right to change this documentation without prior notice. Information provided by SUNPLUS TECHNOLO Car DVD New GUI IR Flow User Manual V0.1 Jan 25, 2008 19, Innovation First Road Science Park Hsin-Chu Taiwan 300 R.O.C. Tel: 886-3-578-6005 Fax: 886-3-578-4418 Web: www.sunplus.com Important Notice SUNPLUS

More information

* 1 * *1 *2 2

* 1 * *1 *2 2 * 1 * 2 1 2 *1 *2 2 3 1 2 7 bo 8 9 6 5 4 3 bn bm bl bk 1 2 3 * 4 5 6 7 8 9 bk bl p bq bp bm * bn bo bp bq * br br 8 . bs br bq bp bo 1234567 bo bnbm bl 8 9 bk 1 2 3 4 5 6 7 8 9 bk b bl bm bn bo bp

More information

S325A 2

S325A 2 TX-NR609 S325A 2 ON/STANDBY ON/STANDBY POWER POWER ON/STANDBY POWER 3 2 2 3 3 * 4 VCR/DVR ON/STANDBY 69 5 * *2 *3*4 -*5 *5 *6 *7 *6 *6 *6 *8 *9 * *0 *9 6 * *2 *3 *4 *5 *6 *7 *8 *9 *0 *0 7 ON/STANDBY 22

More information

Cube20S small, speedy, safe Eextremely modular Up to 64 modules per bus node Quick reaction time: up to 20 µs Cube20S A new Member of the Cube Family

Cube20S small, speedy, safe Eextremely modular Up to 64 modules per bus node Quick reaction time: up to 20 µs Cube20S A new Member of the Cube Family small, speedy, safe Eextremely modular Up to 64 modules per bus de Quick reaction time: up to 20 µs A new Member of the Cube Family Murrelektronik s modular I/O system expands the field-tested Cube family

More information

Preface This guide is intended to standardize the use of the WeChat brand and ensure the brand's integrity and consistency. The guide applies to all d

Preface This guide is intended to standardize the use of the WeChat brand and ensure the brand's integrity and consistency. The guide applies to all d WeChat Search Visual Identity Guidelines WEDESIGN 2018. 04 Preface This guide is intended to standardize the use of the WeChat brand and ensure the brand's integrity and consistency. The guide applies

More information

E15-3D1 1. Specifications Compact 4-Way Cassette type Model name MMU- AP0071MH2UL AP0091MH2UL AP0121MH2UL AP0151MH2UL AP0181MH2UL Cooling Capacity kbt

E15-3D1 1. Specifications Compact 4-Way Cassette type Model name MMU- AP0071MH2UL AP0091MH2UL AP0121MH2UL AP0151MH2UL AP0181MH2UL Cooling Capacity kbt E15-3D1 Compact 4-Way Cassette type MMU-AP0071MH2UL MMU-AP0091MH2UL MMU-AP0121MH2UL MMU-AP0151MH2UL MMU-AP0181MH2UL Contents 1. Specifications 2. Dimensions 3. Center of gravity 4. Piping diagram 5. Wiring

More information

r_09hr_practical_guide_kor.pdf

r_09hr_practical_guide_kor.pdf PRACTICAL GUIDE TO THE EDIROL R-09HR 3 4 PRACTICAL GUIDE TO THE EDIROL R-09HR 5 Situation 1 6 1 2 3 PRACTICAL GUIDE TO THE EDIROL R-09HR WAV MP3 WAV 24 bit/96 khz WAV 16 bit/44.1 khz MP3 128 kbps/44.1

More information

入學考試網上報名指南

入學考試網上報名指南 入 學 考 試 網 上 報 名 指 南 On-line Application Guide for Admission Examination 16/01/2015 University of Macau Table of Contents Table of Contents... 1 A. 新 申 請 網 上 登 記 帳 戶 /Register for New Account... 2 B. 填

More information

HT-S200F

HT-S200F Sound Bar Operating Instructions GB CT HT-S200F WARNING Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. For the AC adapter Labels for AC adapter Model No. and

More information

Microsoft PowerPoint - ATF2015.ppt [相容模式]

Microsoft PowerPoint - ATF2015.ppt [相容模式] Improving the Video Totalized Method of Stopwatch Calibration Samuel C.K. Ko, Aaron Y.K. Yan and Henry C.K. Ma The Government of Hong Kong Special Administrative Region (SCL) 31 Oct 2015 1 Contents Introduction

More information

CONGRATULATIONS ON YOUR PURCHASE OF OUR CAMERA This product has been carefully inspected through rigid quality control before shipment. With reasonabl

CONGRATULATIONS ON YOUR PURCHASE OF OUR CAMERA This product has been carefully inspected through rigid quality control before shipment. With reasonabl INSTRUCTIONS MANUAL SMOKE DETECTOR COLOR, B/W CCD CAMERA CONTENTS English / Chinese PREFACE SAFETY INSTRUCTIONS FUNCTION DESCRIPTION INSTALLATION SPECIFICATIONS PR0210SDE2 Thank you very much for purchasing

More information

HC50246_2009

HC50246_2009 Page: 1 of 7 Date: June 2, 2009 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified by the vendor as:

More information

WFC40810

WFC40810 9000086873 (PD 85 05 10) Operating and Installation Instructions Please read this specification carefully before you use the product. Any failure and losses caused by ignoring the above mentioned items

More information

Microsoft PowerPoint - STU_EC_Ch08.ppt

Microsoft PowerPoint - STU_EC_Ch08.ppt 樹德科技大學資訊工程系 Chapter 8: Counters Shi-Huang Chen Fall 2010 1 Outline Asynchronous Counter Operation Synchronous Counter Operation Up/Down Synchronous Counters Design of Synchronous Counters Cascaded Counters

More information

您 對 本 產 品 的 選 擇 充 分 顯 示 了 您 對 音 響 設 備 的 精 通, 我 們 十 分 感 謝 您 的 惠 顧, 並 為 本 公 司 提 供 優 質 產 品 一 貫 傳 統 而 感 到 無 比 的 自 豪 為 使 您 的 裝 置 與 使 用 能 得 到 最 好 的 發 揮, 我 們

您 對 本 產 品 的 選 擇 充 分 顯 示 了 您 對 音 響 設 備 的 精 通, 我 們 十 分 感 謝 您 的 惠 顧, 並 為 本 公 司 提 供 優 質 產 品 一 貫 傳 統 而 感 到 無 比 的 自 豪 為 使 您 的 裝 置 與 使 用 能 得 到 最 好 的 發 揮, 我 們 NT-503 USB DAC/Network Player 關 於 此 機 器 的 網 路 功 能, 請 看 網 路 說 明 書 使 用 者 說 明 書 與 網 路 說 明 書 可 以 從 TEAC Global Site (http://www.teac-global.com/) 下 載 USB D/A 轉 換 器 / 網 路 播 放 機 使 用 說 明 書 欲 播 放 USB 快 閃 記 憶 體

More information

HCD0174_2008

HCD0174_2008 Reliability Laboratory Page: 1 of 5 Date: December 23, 2008 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified

More information

Microsoft Word - HC20138_2010.doc

Microsoft Word - HC20138_2010.doc Page: 1 of 7 Date: April 26, 2010 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified by the vendor as:

More information

GH1220 Hall Switch

GH1220 Hall Switch Unipolar Hall Switch - Medium Sensitivity Product Description The DH220 is a unipolar h all switch designed in CMOS technology. The IC internally includes a voltage regulator, Hall sensor with dynamic

More information

Microsoft Word - LR1122B-B.doc

Microsoft Word - LR1122B-B.doc UNISONIC TECHNOLOGIES CO., LTD LOW NOISE ma LDO REGULATOR DESCRIPTION The UTC is a typical LDO (linear regulator) with the features of High output voltage accuracy, low supply current, low ON-resistance,

More information

Xear 3D USB CH-IN-2 SPKs 2 6 :

Xear 3D USB CH-IN-2 SPKs 2 6 : 13 6 CH-IN-2 SPKs 2 6 : 13 2003 7 0 13 Notice The content furnished in this document is C-Media audio product knowledge for customers reference However, C-Media Inc assumes no responsibility for the consequences

More information

1. 請 先 檢 查 包 裝 內 容 物 AC750 多 模 式 無 線 分 享 器 安 裝 指 南 安 裝 指 南 CD 光 碟 BR-6208AC 電 源 供 應 器 網 路 線 2. 將 設 備 接 上 電 源, 即 可 使 用 智 慧 型 無 線 裝 置 進 行 設 定 A. 接 上 電 源

1. 請 先 檢 查 包 裝 內 容 物 AC750 多 模 式 無 線 分 享 器 安 裝 指 南 安 裝 指 南 CD 光 碟 BR-6208AC 電 源 供 應 器 網 路 線 2. 將 設 備 接 上 電 源, 即 可 使 用 智 慧 型 無 線 裝 置 進 行 設 定 A. 接 上 電 源 1. 請 先 檢 查 包 裝 內 容 物 AC750 多 模 式 無 線 分 享 器 安 裝 指 南 安 裝 指 南 CD 光 碟 BR-6208AC 電 源 供 應 器 網 路 線 2. 將 設 備 接 上 電 源, 即 可 使 用 智 慧 型 無 線 裝 置 進 行 設 定 A. 接 上 電 源 B. 啟 用 智 慧 型 裝 置 的 無 線 Wi-Fi C. 選 擇 無 線 網 路 名 稱 "edimax.setup"

More information

C o n t e n t s...7... 15 1. Acceptance... 17 2. Allow Love... 19 3. Apologize... 21 4. Archangel Metatron... 23 5. Archangel Michael... 25 6. Ask for

C o n t e n t s...7... 15 1. Acceptance... 17 2. Allow Love... 19 3. Apologize... 21 4. Archangel Metatron... 23 5. Archangel Michael... 25 6. Ask for Doreen Virtue, Ph.D. Charles Virtue C o n t e n t s...7... 15 1. Acceptance... 17 2. Allow Love... 19 3. Apologize... 21 4. Archangel Metatron... 23 5. Archangel Michael... 25 6. Ask for a Sign... 27 7.

More information

Microsoft Word - 第四組心得.doc

Microsoft Word - 第四組心得.doc 徐 婉 真 這 四 天 的 綠 島 人 權 體 驗 營 令 我 印 象 深 刻, 尤 其 第 三 天 晚 上 吳 豪 人 教 授 的 那 堂 課, 他 讓 我 聽 到 不 同 於 以 往 的 正 義 之 聲 轉 型 正 義, 透 過 他 幽 默 熱 情 的 語 調 激 起 了 我 對 政 治 的 興 趣, 願 意 在 未 來 多 關 心 社 會 多 了 解 政 治 第 一 天 抵 達 綠 島 不 久,

More information

WVT new

WVT new Operating and Installation Instructions 5120 004601 (PD 84 09 25) Please read this specification carefully before you use the product. Any failure and losses caused by ignoring the above mentioned items

More information

HC20131_2010

HC20131_2010 Page: 1 of 8 Date: April 14, 2010 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified by the vendor as:

More information

RX-5042S[UT]

RX-5042S[UT] TA/NEWS/INFO DISPLAY MODE AUDIO/VIDEO CONTROL RECEIVER RX-5042S INSTRUCTIONS LVT1140-006A [UT] STANDBY/ON STANDBY/ON RX-5042S G-1 ... 2... 4... 4... 4... 4 FM AM... 4... 5... 6 7... 6 7... 8... 8... 8...

More information

WARNING Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To reduce the risk of fire, do not cover the ventila

WARNING Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To reduce the risk of fire, do not cover the ventila The software of this system may be updated in the future. To find out details on any available updates, please visit the following URL. http://www.sony-asia.com/section/support Sound Bar Operating Instructions

More information

2015 Chinese FL Written examination

2015 Chinese FL Written examination Victorian Certificate of Education 2015 SUPERVISOR TO ATTACH PROCESSING LABEL HERE Letter STUDENT NUMBER CHINESE FIRST LANGUAGE Written examination Monday 16 November 2015 Reading time: 11.45 am to 12.00

More information

SHIMPO_表1-表4

SHIMPO_表1-表4 For servo motor ABLEREDUCER L Series Features Coaxial shaft series L series Helical gears contribute to reduce vibration and noise. Standard backlash is 5 arc-min, ideal for precision control. High rigidity

More information

AS4610 Series QSG-EN_SC_TC R02.book

AS4610 Series QSG-EN_SC_TC R02.book Quick Start Guide 4/48-Port GE Data Center Switch AS460-0T AS460-0P AS460-54T AS460-54P. Unpack the Switch and Check Contents AS460-0T AS460-0P Note: The switch can also be installed on a desktop or shelf

More information

Pneumonia - Traditional Chinese

Pneumonia - Traditional Chinese Pneumonia When you have pneumonia, the air sacs in the lungs fill with infection or mucus. Pneumonia is caused by a bacteria, virus or chemical. It is not often passed from one person to another. Signs

More information

WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR PORTABLE CART WARNING S325A CT-2

WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR PORTABLE CART WARNING S325A CT-2 FR-N3X WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR PORTABLE CART WARNING S325A CT-2 CT-3 CLASS LASER PRODUCT CT-4 CT-5 6 mm mm 3 mm 6 5mm 2 CT-6 2 CT-7 2 3 0mm

More information

8260

8260 8260 2004 9 Lenovo 15 32 1 60 40 60 2 ... 6... 6... 7... 9... 11... 14... 15... 15... 16... 17 PictBridge... 18... 19... 19 Lenovo... 21 Lenovo... 23... 24... 25 Lenovo... 28... 29 3 ... 30... 30... 31...

More information

1

1 Application Chuck Instruction Manual Universal Ball Lock Power Chuck APPLICATION CHUCK PBL CHUCK (UNIVERSAL BALL LOCK POWER CHUCK) TABLE OF CONTENTS Keep this manual handy for easy reference as it will

More information

HOIE WITH PREISION is also the Easy choice! Easy-Laser Easy-Laser

HOIE WITH PREISION is also the Easy choice! Easy-Laser Easy-Laser E915 1 HOIE WITH PREISION is also the Easy choice! Easy-Laser Easy-Laser SIMPLE ND EFFETIVE Easy-Laser D23 Easy-Laser E5 TEHNIL DT System Relative humidity 10 95% (complete system) 12.1 kg [26.7 lbs] arrying

More information

MODEL COLOR LIST UZ125D2 YMW GRAY YNF RED YRG BLUE 30H WHITE

MODEL COLOR LIST UZ125D2 YMW GRAY YNF RED YRG BLUE 30H WHITE MODEL COLOR LIST UZ125D2 YMW GRAY YNF RED YRG BLUE 30H WHITE MODEL COLOR LIST UZ125D2K K13 BLACK YRG BLUE YPK WHITE MODEL COLOR LIST UZ125X2 G22 Q05 GRAY ORANGE GREEN WHITE N28 W08 PREFACE When it becomes

More information

5in1_eDVR_Manual_Chinese.cdr

5in1_eDVR_Manual_Chinese.cdr 02 English User Manual 29 User Manual Contents 2 5 6 7 8 9 10 11 12 14 17 18 19 20 21 22 23 24 25 26 27 Quick start Controls Accessories Minimum System Requirements Battery Charge Power On/Off LCM Indicator

More information

Microsoft Word - PZ series.doc

Microsoft Word - PZ series.doc 叠 层 片 式 铁 氧 体 磁 珠 P 系 列 Multilayer Chip Ferrite Bead P Series Operating Temp. : -4 ~ +8 特 征 FEATUES 内 部 印 有 银 电 极 的 叠 层 结 构, 铁 氧 体 屏 蔽 无 串 扰 Internal silver printed layers and magnetic shielded structures

More information

2015年4月11日雅思阅读预测机经(新东方版)

2015年4月11日雅思阅读预测机经(新东方版) 剑 桥 雅 思 10 第 一 时 间 解 析 阅 读 部 分 1 剑 桥 雅 思 10 整 体 内 容 统 计 2 剑 桥 雅 思 10 话 题 类 型 从 以 上 统 计 可 以 看 出, 雅 思 阅 读 的 考 试 话 题 一 直 广 泛 多 样 而 题 型 则 稳 中 有 变 以 剑 桥 10 的 test 4 为 例 出 现 的 三 篇 文 章 分 别 是 自 然 类, 心 理 研 究 类,

More information

HC70245_2008

HC70245_2008 Reliability Laboratory Page: 1 of 6 Date: September 5, 2008 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified

More information

Pin Configurations Figure2. Pin Configuration of FS2012 (Top View) Table 1 Pin Description Pin Number Pin Name Description 1 GND 2 FB 3 SW Ground Pin.

Pin Configurations Figure2. Pin Configuration of FS2012 (Top View) Table 1 Pin Description Pin Number Pin Name Description 1 GND 2 FB 3 SW Ground Pin. Features Wide 3.6V to 32V Input Voltage Range Output Adjustable from 0.8V to 30V Maximum Duty Cycle 100% Minimum Drop Out 0.6V Fixed 300KHz Switching Frequency 12A Constant Output Current Capability Internal

More information

AL-M200 Series

AL-M200 Series NPD4754-00 TC ( ) Windows 7 1. [Start ( )] [Control Panel ()] [Network and Internet ( )] 2. [Network and Sharing Center ( )] 3. [Change adapter settings ( )] 4. 3 Windows XP 1. [Start ( )] [Control Panel

More information

2005 5,,,,,,,,,,,,,,,,, , , 2174, 7014 %, % 4, 1961, ,30, 30,, 4,1976,627,,,,, 3 (1993,12 ),, 2

2005 5,,,,,,,,,,,,,,,,, , , 2174, 7014 %, % 4, 1961, ,30, 30,, 4,1976,627,,,,, 3 (1993,12 ),, 2 3,,,,,, 1872,,,, 3 2004 ( 04BZS030),, 1 2005 5,,,,,,,,,,,,,,,,, 1928 716,1935 6 2682 1928 2 1935 6 1966, 2174, 7014 %, 94137 % 4, 1961, 59 1929,30, 30,, 4,1976,627,,,,, 3 (1993,12 ),, 2 , :,,,, :,,,,,,

More information

Rotary Switch Catalogue

Rotary Switch Catalogue Rotary Switches RS300/400/500 Series Outline Our RS series embody the manufacturing history of our company. All series are sturdy and solid with high dependability designed for control units of plants,

More information

SA-DK2-U3Rユーザーズマニュアル

SA-DK2-U3Rユーザーズマニュアル USB3.0 SA-DK2-U3R 2007.0 2 3 4 5 6 7 8 System Info. Manual Rebuild Delete RAID RAID Alarm Rebuild Rate Auto compare Temp Management Load Default Elapse time Event Log 0 2 3 4 2 3 4 ESC 5

More information

安 全 資 訊 重 要 安 全 指 示 1. 閱 讀 這 些 指 示 2. 保 留 這 些 指 示 3. 留 意 所 有 警 示 4. 遵 循 所 有 指 示 5. 不 要 在 水 源 附 近 使 用 該 產 品 6. 使 用 乾 布 擦 拭 機 器 7. 不 要 阻 塞 任 何 通 風 口 按 照

安 全 資 訊 重 要 安 全 指 示 1. 閱 讀 這 些 指 示 2. 保 留 這 些 指 示 3. 留 意 所 有 警 示 4. 遵 循 所 有 指 示 5. 不 要 在 水 源 附 近 使 用 該 產 品 6. 使 用 乾 布 擦 拭 機 器 7. 不 要 阻 塞 任 何 通 風 口 按 照 AV 收 音 擴 大 機 1 使 用 手 冊 安 全 資 訊 重 要 安 全 指 示 1. 閱 讀 這 些 指 示 2. 保 留 這 些 指 示 3. 留 意 所 有 警 示 4. 遵 循 所 有 指 示 5. 不 要 在 水 源 附 近 使 用 該 產 品 6. 使 用 乾 布 擦 拭 機 器 7. 不 要 阻 塞 任 何 通 風 口 按 照 用 戶 手 冊 來 安 裝 該 產 品 8. 不 要

More information

User’s Manual

User’s Manual SNAP 500 打 印 机 用 户 手 册 1 用 户 手 册 SNAP TM 500 打 印 机 2015 年 8 月 24 日 AVERY DENNISON Manual Edition 2.5 2 SNAP 500 打 印 机 用 户 手 册 WARNING This device complies with Part 15 of the FCC Rules. Operation is subject

More information

SHIMPO_表1-表4

SHIMPO_表1-表4 For servo motor ABLEREDUCER SSeries Coaxial shaft series Features S series Standard backlash is 3 arc-min, ideal for precision control. High rigidity & high torque were achived by uncaged needle roller

More information

Product Specification Chip Intel DSL6540 Thunderbolt 3 Controller Connectors 2 x Thunderbolt 3 ports (Thunderbolt 3 Port 1/Thunderbolt 3 Port 2), supp

Product Specification Chip Intel DSL6540 Thunderbolt 3 Controller Connectors 2 x Thunderbolt 3 ports (Thunderbolt 3 Port 1/Thunderbolt 3 Port 2), supp GC-ALPINE RIDGE Installation Guide/ 12WE6-ALPINER-10AR Product Specification Chip Intel DSL6540 Thunderbolt 3 Controller Connectors 2 x Thunderbolt 3 ports (Thunderbolt 3 Port 1/Thunderbolt 3 Port 2),

More information

WARNING Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To reduce the risk of fire, do not cover the ventila

WARNING Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To reduce the risk of fire, do not cover the ventila Sound Bar Operating Instructions GB CT The software of this system may be updated in the future. To find out details on any available updates, please visit the following URL. http://www.sony-asia.com/section/support

More information

2010 Japanese First Language Written examination

2010 Japanese First Language Written examination Victorian Certificate of Education 2010 SUPERVISOR TO ATTACH PROCESSING LABEL HERE STUDENT NUMBER Letter Figures Words JAPANESE FIRST LANGUAGE Written examination Monday 15 November 2010 Reading time:

More information

untitled

untitled LBS Research and Application of Location Information Management Technology in LBS TP319 10290 UDC LBS Research and Application of Location Information Management Technology in LBS , LBS PDA LBS

More information

iml v C / 4W Down-Light EVM - pplication Notes. IC Description The iml8683 is a Three Terminal Current Controller (TTCC) for regulating the cur

iml v C / 4W Down-Light EVM - pplication Notes. IC Description The iml8683 is a Three Terminal Current Controller (TTCC) for regulating the cur iml8683-220v C / 4W Down-Light EVM - pplication Notes iml8683 220V C 4W Down Light EVM pplication Notes Table of Content. IC Description... 2 2. Features... 2 3. Package and Pin Diagrams... 2 4. pplication

More information

OVLFx3C7_Series_A3_bgry-KB.pub

OVLFx3C7_Series_A3_bgry-KB.pub (5 mm) x High brightness with well-defined spatial radiation patterns x U-resistant epoxy lens x Blue, green, red, yellow Product Photo Here Each device in the OLFx3C7 series is a high-intensity LED mounted

More information

Microsoft Word - 3. Vitroefication_using_EMGP.docx

Microsoft Word - 3. Vitroefication_using_EMGP.docx EM GP 冷 冻 样 品 制 备 实 习 教 程 (Xiaojun Huang, Gang Ji) 每 位 演 示 及 带 领 学 员 实 习 EM GP 冷 冻 样 品 制 备 的 老 师 的 材 料 清 单 : 1)15 个 GIG 载 网 2) 冷 冻 样 品 Ferritin 或 Ribosome 3)EM GP 专 用 镊 子 1 把 4)1-10ul 移 液 器,1 把 ( 移 液 器

More information

IMPORTANT SAFETY INSTRUCTIONS / When using an electrical appliance, basic safety precautions should always be followed, including the following:read a

IMPORTANT SAFETY INSTRUCTIONS / When using an electrical appliance, basic safety precautions should always be followed, including the following:read a 1-NEEDLE, 3-THREAD OVERLOCK SEWING MACHINE MO-623 INSTRUCTION MANUAL IMPORTANT: READ ALL SAFETY REGULATIONS CAREFULLY AND UNDERSTAND THEM BEFORE USING YOUR SEWING MACHINE. RETAIN THIS INSTRUCTION MANUAL

More information

iml88-0v C / 8W T Tube EVM - pplication Notes. IC Description The iml88 is a Three Terminal Current Controller (TTCC) for regulating the current flowi

iml88-0v C / 8W T Tube EVM - pplication Notes. IC Description The iml88 is a Three Terminal Current Controller (TTCC) for regulating the current flowi iml88-0v C / 8W T Tube EVM - pplication Notes iml88 0V C 8W T Tube EVM pplication Notes Table of Content. IC Description.... Features.... Package and Pin Diagrams.... pplication Circuit.... PCB Layout

More information

MODEL 62000H SERIES 5KW / 10KW / 15KW 0 ~ 375A 0 ~ 1000V/2000V( ) : 200/220Vac, 380/400Vac, 440/480Vac 3U/15KW / & 150KW / ( 10 ms ~ 99 hours)

MODEL 62000H SERIES 5KW / 10KW / 15KW 0 ~ 375A 0 ~ 1000V/2000V( ) : 200/220Vac, 380/400Vac, 440/480Vac 3U/15KW / & 150KW / ( 10 ms ~ 99 hours) MODEL 62000H SERIES 5KW / 10KW / 15KW 0 ~ 375A 0 ~ 1000V/2000V( ) : 200/220Vac, 380/400Vac, 440/480Vac 3U/15KW / &150KW / ( 10 ms ~ 99 hours) 10 100 / PROGRAMMABLE DC POWER SUPPLY MODEL 62000H SERIES USB

More information

CL-68x00,00,00,00,00, CL-78x00,00,00,00,6000 Spindle 181mm mm Spindle bore 181mm is standard. 255,5 or 5mm is option. Chuck is optional. You ca

CL-68x00,00,00,00,00, CL-78x00,00,00,00,6000 Spindle 181mm mm Spindle bore 181mm is standard. 255,5 or 5mm is option. Chuck is optional. You ca CNC KINWA FLAT BED CNC LATHE CL-68x00 CL-68/CL-78 Series Swing 11, mm Between centers 00~7000mm Spindle bore 181, 255, 5, 5mm Spindle motor 60HP CL-68x00,00,00,00,00, CL-78x00,00,00,00,6000 Spindle 181mm

More information

LK110_ck

LK110_ck Ck 电子琴 LK110CK1A Ck-1 1. 2. 1. 2. 3. (+) ( ) Ck-2 1. 2. 3. * 1. 2. 3. Ck-3 Ck-4 LCD LCD LCD LCD LCD LCD 15 * * / MIDI Ck-5 100 50 100 100 100 1 2 MIDI MIDI Ck-6 ... Ck-1... Ck-6... Ck-8... Ck-9... Ck-10...

More information

iml v C / 0W EVM - pplication Notes. IC Description The iml8683 is a Three Terminal Current Controller (TTCC) for regulating the current flowin

iml v C / 0W EVM - pplication Notes. IC Description The iml8683 is a Three Terminal Current Controller (TTCC) for regulating the current flowin iml8683-220v C / 0W EVM - pplication Notes iml8683 220V C 0W EVM pplication Notes Table of Content. IC Description... 2 2. Features... 2 3. Package and Pin Diagrams... 2 4. pplication Circuit... 3 5. PCB

More information

Windows XP

Windows XP Windows XP What is Windows XP Windows is an Operating System An Operating System is the program that controls the hardware of your computer, and gives you an interface that allows you and other programs

More information

untitled

untitled 20 90 1998 2001 1 Abstract Under the environment of drastic competitive market, risk and uncertainty that the enterprise faces are greater and greater, the profit ability of enterprise assets rises and

More information

Microsoft PowerPoint - Aqua-Sim.pptx

Microsoft PowerPoint - Aqua-Sim.pptx Peng Xie, Zhong Zhou, Zheng Peng, Hai Yan, Tiansi Hu, Jun-Hong Cui, Zhijie Shi, Yunsi Fei, Shengli Zhou Underwater Sensor Network Lab 1 Outline Motivations System Overview Aqua-Sim Components Experimental

More information

B _02_ch.indd

B _02_ch.indd KDC-X8016BT KDC-X8016BTL KDC-X7016 KDC-X7016L B64-4521-10/02 (MW) 2 KDC-X8016BT/ KDC-X8016BTL/ KDC-X7016/ KDC-X7016L 3 2 > > 1 2 3 4 5 6 AUX 7 8 9 10 11 12 13 14 1 2 3 4 5 6 7 8 9 4 10 38 11 12 13 14 4

More information

UTI (Urinary Tract Infection) - Traditional Chinese

UTI (Urinary Tract Infection) - Traditional Chinese UTI (Urinary Tract Infection) Urinary tract infection, also called UTI, is an infection of the bladder or kidneys. Urethra Kidney Ureters Bladder Vagina Kidney Ureters Bladder Urethra Penis Causes UTI

More information

FILTRON 1. DC AC AC 220V 50HZ 2. 1 1 1 3. / / / / 4. 1) 2 3 4 5 6 5. 6. 7. 8. 9. / 10. 1. 2. 3. 4. 5. 6. 7. DC AC FILTRON DC AC FILTRON DC 12V 12VDC D

FILTRON 1. DC AC AC 220V 50HZ 2. 1 1 1 3. / / / / 4. 1) 2 3 4 5 6 5. 6. 7. 8. 9. / 10. 1. 2. 3. 4. 5. 6. 7. DC AC FILTRON DC AC FILTRON DC 12V 12VDC D 2006 4 27 1 JY FILTRON 1. DC AC AC 220V 50HZ 2. 1 1 1 3. / / / / 4. 1) 2 3 4 5 6 5. 6. 7. 8. 9. / 10. 1. 2. 3. 4. 5. 6. 7. DC AC FILTRON DC AC FILTRON DC 12V 12VDC DC FILTRON AC 24VAC 24VAC AC 24VAC AC

More information

* RRB *

* RRB * *9000000000RRB0010040* *9000000000RRB0020040* *9000000000RRB0030040* *9000000000RRB0040040* *9000000000RRC0010050* *9000000000RRC0020050* *9000000000RRC0030050* *9000000000RRC0040050* *9000000000RRC0050050*

More information

Bottle Feeding Your Baby - Simplified Chinese

Bottle Feeding Your Baby - Simplified Chinese Bottle Feeding Your Baby Bottle feeding with formula will meet your baby s food needs. Your doctor will help decide which formula is right for your baby. Never give milk from cows or goats to a baby during

More information

Microsoft Word - AP1515V02

Microsoft Word - AP1515V02 Document No. Rev.: V0.20 Page: 1 of 9 Revision History Rev. DRN # History Initiator Effective Date V01 V02 Initial document 黃宗文 Add second package description 葉宗榮 2014/05/15 2015/09/08 Initiator: 雷晨妤 (DCC)

More information

4. 每 组 学 生 将 写 有 习 语 和 含 义 的 两 组 卡 片 分 别 洗 牌, 将 顺 序 打 乱, 然 后 将 两 组 卡 片 反 面 朝 上 置 于 课 桌 上 5. 学 生 依 次 从 两 组 卡 片 中 各 抽 取 一 张, 展 示 给 小 组 成 员, 并 大 声 朗 读 卡

4. 每 组 学 生 将 写 有 习 语 和 含 义 的 两 组 卡 片 分 别 洗 牌, 将 顺 序 打 乱, 然 后 将 两 组 卡 片 反 面 朝 上 置 于 课 桌 上 5. 学 生 依 次 从 两 组 卡 片 中 各 抽 取 一 张, 展 示 给 小 组 成 员, 并 大 声 朗 读 卡 Tips of the Week 课 堂 上 的 英 语 习 语 教 学 ( 二 ) 2015-04-19 吴 倩 MarriottCHEI 大 家 好! 欢 迎 来 到 Tips of the Week! 这 周 我 想 和 老 师 们 分 享 另 外 两 个 课 堂 上 可 以 开 展 的 英 语 习 语 教 学 活 动 其 中 一 个 活 动 是 一 个 充 满 趣 味 的 游 戏, 另 外

More information

K7VT2_QIG_v3

K7VT2_QIG_v3 ............ 1 2 3 4 5 [R] : Enter Raid setup utility 6 Press[A]keytocreateRAID RAID Type: JBOD RAID 0 RAID 1: 2 7 RAID 0 Auto Create Manual Create: 2 RAID 0 Block Size: 16K 32K

More information

TX-NR509 Cs

TX-NR509 Cs TX-NR509 S325A 2 ON/STANDBY 3 8 8 2 28 4 * 4 VCR/DVR ON/STANDBY 59 5 **2 *3 *4 * *2 *3 - *4 *5 *6 *5 *6 * *8 *6 *7 *7 *7 *7 *8 *8 6 ON/STANDBY 9 ZONE 2 OFF 52 4 8 LISTENING MODE 3 RT/PTY/TP 27 MEMORY 26

More information

REMOTEAIRPRO说明书中英文版

REMOTEAIRPRO说明书中英文版 REMOTE AIR PRO Product Manual Welcome to your new REMOTE AIR PRO REMOTE AIR PRO Whatʼs Included Instruction manual 1 Motor Installation The motor is mounted on 19 mm or 15 mm rods. For 15 mm rods use

More information

pdf

pdf 88% 84% OK 1 3 1.1 1.2 1.3 (1) (1) (1) 1/7/2013 (2) (3) (2) (2) 1/7/2013 (4) (5) (6) (7) (3) (4) (3) (4) (5) 1/7/2013 1/7/2013 1/7/2013 (6) 1/7/2013 2 (7) 1/9/2013 2.1 (8) 1/9/2013 (9) 1/12/2013 2.2 2.3

More information

V6800/V6600 3D

V6800/V6600 3D V6800/V6600 3D V6600/V6800 3D R 2000 2 3 4 5 R 6 7 8 The VIP (Video Interface Port) Connector are used for third party add-on modules, such as video capture cards or television tuners. DDR: Double Data

More information

2016杂志第1期.FIT)

2016杂志第1期.FIT) 刊 首 寄 语 PREFACE 文 苑 艺 圃 荫 马 合 荣 重 回 刀 尔 登 十 多 年 前, 为 了 祖 国 的 三 线 建 设, 为 了 祖 国 的 国 防 事 业, 情 地 围 着 我 问 这 儿 问 那 儿, 一 切 就 好 像 发 生 在 昨 天 一 年 级, 我 的 父 母 把 我 带 到 了 石 人 山 下, 青 龙 河 边, 带 到 了 刀 尔 登 热 因 为 听 到 老 师

More information

Microsoft Word - 11月電子報1130.doc

Microsoft Word - 11月電子報1130.doc 發 行 人 : 楊 進 成 出 刊 日 期 2008 年 12 月 1 日, 第 38 期 第 1 頁 / 共 16 頁 封 面 圖 話 來 來 來, 來 葳 格 ; 玩 玩 玩, 玩 數 學 在 11 月 17 到 21 日 這 5 天 裡 每 天 一 個 題 目, 孩 子 們 依 據 不 同 年 段, 尋 找 屬 於 自 己 的 解 答, 這 些 數 學 題 目 和 校 園 情 境 緊 緊 結

More information