CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future

Size: px
Start display at page:

Download "CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future"

Transcription

1 LV Front Surround System (YAS-CU203+NS-WSW41) Owner s Manual Manual de Instrucciones

2 CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. Install this unit in a well ventilated, cool, dry, clean place - away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. For proper ventilation, allow the following minimum clearances. Sound bar: Top: 10 cm (4 in), Rear: 10 cm (4 in), Sides: 10 cm (4 in) Subwoofer: Top: 20 cm (8 in), Rear: 20 cm (8 in), Sides: 20 cm (8 in) Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury. Avoid installing this unit where foreign objects may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: Other components, as they may cause damage and/or discoloration on the surface of this unit. Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury. Containers with liquid in them, as they may fall and liquid may cause electrical shock to the user and/or damage to this unit. Do not cover this unit with a newspaper, tablecloth, curtain, etc., in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury. Do not plug in this unit to a wall outlet until all connections are complete. Do not operate this unit upside-down. It may overheat, possibly causing damage. Do not use force on switches, knobs and/or cords. When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cable. Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. Yamaha will not be held responsible for any damage resulting from use of this unit with a voltage other than specified. To prevent damage by lightning, keep the power cable and outdoor antennas disconnected from a wall outlet or the unit during a lightning storm. Do not attempt to modify or fix this unit. Contact qualified Yamaha service personnel when any service is needed. The cabinet should never be opened for any reasons. When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet. Be sure to read the Troubleshooting section on common operating errors before concluding that this unit is faulty. Before moving this unit, press to set this unit in standby mode, and disconnect the power supply cable from the wall outlet. Condensation will form when the surrounding temperature changes suddenly. Disconnect the power supply cable from the outlet, then leave the unit alone. Install this unit near the wall outlet and where the AC power plug can be reached easily. Secure placement or installation is the owner s responsibility. Yamaha shall not be liable for any accident caused by improper placement or installation of speakers. Do not put a hand or foreign object into the port on the subwoofer. When moving the subwoofer, do not hold the port, as it may cause personal injury and/or damage to this unit. Do not place a fragile object near the port of the subwoofer. If the object falls as a result of the air pressure, it may cause personal injury and/or damage to the subwoofer and the object. Keep the product out of reach of children to avoid them swallowing small parts. Notes on remote controls and batteries Do not spill water or other liquids on the remote control. Do not drop the remote control. Do not leave or store the remote control in the following places: places of high humidity, such as near a bath places of high temperatures, such as near a heater or a stove places of extremely low temperatures dusty places Do not expose the remote control sensor of this unit to direct sunlight or lighting such as inverted fluorescent lamps. If the batteries grow old, the effective operation range of the remote control decreases considerably. If this happens, replace the batteries with two new ones as soon as possible. Do not use old batteries together with new ones. Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color. Exhausted batteries may leak. If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. Do not carry batteries in a pocket or purse with metal objects like coins, etc. Do not throw away batteries with general house waste. Dispose of them correctly in accordance with your local regulations. Keep batteries away from children. If a battery is accidentally swallowed, contact your doctor immediately. When not planning to use the remote control for long periods of time, remove the batteries from the remote control. Do not charge or disassemble the supplied batteries. The batteries shall not be exposed to excessive heat such as sunshine, fire or like. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by. In this state, this unit is designed to consume a very small quantity of power. (Power key) Turns on the power of this unit or sets it to the standby mode. Do not use this unit within 22 cm (9 inches) of persons with a heart pacemaker implant or defibrillator implant. Radio waves may affect electro-medical devices. Do not use this unit near medical devices or inside medical facilities. The name plate is located on the bottom of the unit. i En

3 Contents Supplied items... 2 Features... 3 Frequently asked questions... 3 Part names and functions (sound bar/subwoofer)... 4 Installation... 5 Connections... 6 Operations... 8 Listening to the sound from a Bluetooth device Settings Programming the sound bar with the TV s remote control (TV s remote control learning function) Sending the TV s remote signal through the sound bar (TV Remote Repeater function) Setting the auto power standby function Initializing the sound bar Troubleshooting Specifications About this manual NOTE This indicates precautions for use of the product and its feature limitations. HINT This indicates supplementary explanations for better use. En 1

4 Supplied items Make sure you have received all of the following items. How to use the remote control Preparing the remote control Peel off the protection sheet before use. Sound bar (YAS-CU203) Battery x 2 (AAA, R03, UM4) Wireless subwoofer (NS-WSW41) Remote control Optical cable (1.5 m [4.9 ft]) Operating range of the remote control Remain within the operating range shown below. Remote control sensor Within 6 m (20 ft) Mounting template * Using when attaching the sound bar to a wall Stand x 2 (For sound bar) Screw x 2 (For attaching the stand) Owner s Manual (This manual) 2 En

5 Features Enjoy powerful and realistic sound from the front surround system consisting of the sound bar and wireless subwoofer, and easy installation and connection to TVs and other devices. AIR SURROUND XTREME Enjoy 7.1 channel surround sound, which creates a wide and deep soundstage, as if speakers are set, not only on the front, but also on the left and right, and behind the listener (p.9). Advanced Bass Extension Processing Equipped with Yamaha s original bass boost technology, this system reproduces more powerful sound from the dedicated subwoofer (p.9). Bluetooth connection Content on a Bluetooth compatible smartphone, tablet, or computer can be played back easily (p.10). You can enjoy deep and fresh sound as close to the original by the Compressed Music Enhancer. The sound bar is also compliant with the aptx codec, which enables you to enjoy better sound from your smartphone. HOME THEATER CONTROLLER You can operate the sound bar easily by installing the dedicated controlling application HOME THEATER CONTROLLER. Frequently asked questions The following section covers popular functions and frequently asked questions about the sound bar. Q1 A1 Q2 A2 Q3 A3 Can I operate the sound bar using the remote control of the TV? Switching between the remote controls of the TV and sound bar is inconvenient. Yes. You can control the sound bar using your TV s remote control by the TV s remote control learning function (p.12). This function is available only for the IR (infrared) remote control. Check your TV s remote control type. The TV s remote control does not work after the sound bar is installed in front of the TV. If your TV s remote control uses IR (infrared) signals, set the TV Remote Repeater function to transmit the TV s remote control signals from the sound bar (p.14). If your TV s remote control uses radio waves, increase the distance between the TV and sound bar. Can I make voice sound more clearly? Yes. Dialogue in movies, TV news or sports programs, etc., can be made clearer using the clear voice function (p.9). TV s remote control learning function Operate the sound bar with the TV s remote control (p.12). TV Remote Repeater function Enables the TV s remote signal to pass through the sound bar. If the installed sound bar blocks the TV s remote sensor, the TV s remote will not work. This function provides a convenient solution (p.14). Clear voice Makes voice sound (such as dialogues and narrations) clear (p.9). UniVolume Maintains consistent sound volume when inputs or sound sources switch (p.9). En 3

6 Part names and functions (sound bar/subwoofer) Sound bar (front panel) Sound bar (rear panel) A Indicators Indicate the status of the sound bar. The indicators will dim automatically if no operations are performed for 5 seconds. Refer to Operations (p.8 to 9) and Wireless connection with the subwoofer (p.7) for the main functions of the indicators. B Remote control sensor Receives infrared signals from the remote control of the sound bar (p.2). C TV s remote control sensor Receives infrared signals from the TV s remote control when the TV Remote Repeater function is enabled (p.14). D INPUT key Selects an input source to be played back (p.8). E MUTE key Mutes the audio output. Press the key again to unmute (p.9). F VOLUME (+/ ) keys Adjust the volume (p.8). G (power) key Turns on or off (standby) the sound bar (p.9). HINT The sound bar may automatically turn off when the auto power standby function is enabled (p.14). H Speakers A TV input jack For connecting to a TV with an optical cable (p.6). B BD/DVD input jack For connecting to a playback device, such as a Blu-ray Disc (BD) player, with a coaxial digital cable (p.6). C ANALOG input jacks For connecting an external device with an RCA stereo cable (p.7). D IR flasher for TV Remote Repeater Transmits TV s remote control signals received at the TV s remote control sensor to the TV (p.14). Subwoofer (rear panel) A STATUS indicator Indicates the status of the subwoofer (p.9). B SUBWOOFER PAIRING button For setting wireless connection between the sound bar and subwoofer (p.19). C Port 4 En

7 Installation Place the sound bar on a flat surface such as on top of a TV cabinet. Place the subwoofer to the outside of the sound bar. To avoid echoes from the wall, face the front side of the subwoofer slightly inward. HINT If it is difficult to operate the TV, use the TV Remote Repeater function (p.14) to transmit the TV s remote control signal via sound bar. When placing the sound bar across the bases of the TV, or when changing the height of the sound bar, attach the supplied stands with the stand attachment screws. How to install on the wall 1 Attach the mounting template on a wall and mark for the screw holes. Tapes or thumbtacks Mounting template (supplied) Screw holes Attaching the sound bar to a wall 2 Remove the mounting template from the wall, then install commercially available screws (as illustrated below) at the points marked on the wall. 7 to 8.5 mm (1/4" to 5/16") 3 to 4 mm (1/8" to 3/16") 4 mm (#8) 20 mm (3/4") or more Cautions Do not stack the sound bar/subwoofer and a BD player or other device directly on each other. Doing so may cause a malfunction due to vibrations. Do not hold the speaker portion (fabric part) on the front of the subwoofer when moving it. The sound bar contains non-magnetic shielding speakers. Do not place magnetically sensitive items (hard disk drive, etc.) near the sound bar. Depending on your installation environment, it may be better to connect the sound bar and external devices (such as a TV) before installing the sound bar. Do not place the sound bar within 50 mm (2") of the TV. The subwoofer and sound bar communicate wirelessly. Do not place objects that block wireless signals, such as metallic furniture and devices, between the subwoofer and sound bar as the wireless communication may be adversely affected. If the subwoofer is covered with a cloth or other object, the sound volume is reduced. Install the subwoofer so that it is not hidden behind a thick curtain, etc. Cautions When installing the sound bar on a wall, all installation work must be performed by a qualified contractor or dealer. The customer must never attempt to perform this installation work. Improper or inadequate installation could cause the sound bar to fall, resulting in personal injury. Do not attach the sound bar to a wall that is made of weak materials such as plaster or veneered woods. Doing so may cause the sound bar to fall. Make sure you use commercially available screws that can support the weight of the installation (specified in Step 2 on the right). Using clamps other than specified screws, such as short screws, nails, and two-sided tape, may cause the sound bar to fall. 3 Hang the sound bar on the screws. Mounting holes on rear of sound bar Cautions Fix the cables in place where they will not become loose. If your foot or hand accidentally gets caught on a loose cable, the sound bar may fall. Check that the sound bar is fixed securely after the installation. Yamaha will bear no responsibility for any accidents caused by improper installations. En 5

8 Connections Connect to a TV (or other peripheral device). Sound bar (rear) Cautions Make sure that the power cables of the sound bar and subwoofer are not connected to AC wall outlets when you start making connections. Do not use excessive force when inserting the cable plug. Doing so may damage the cable plug or terminal. Power cable 1 Connect the TV and sound bar with the optical cable (supplied). Remove the cap of the optical cable and check the direction of the plug. Subwoofer (rear) To AC wall outlet Optical cable Coaxial digital cable (commercially available) 2 Connect the power cables of the sound bar and subwoofer to AC wall outlets. 3 Set the TV as follows. Set the TV volume to minimum. Disable the TV built-in speaker output (if available). HINT If a setting to disable the speaker output is not available on your TV, you may disable it by connecting headphones to the headphone jack on the TV. For details, refer to the manuals of the TV. The TV and BD/DVD input jacks support the following audio signals. PCM (2 channel) Dolby Digital (up to 5.1 channel) DTS Digital Surround (up to 5.1 channel) TV HDMI cable (etc.) OPTICAL OUTPUT Coaxial digital audio output (orange) Power cable To AC wall outlet HINT If your playback device has a coaxial digital audio output, you can connect it to the BD/ DVD input of the sound bar with a coaxial digital cable (commercially available). Playback device (such as a BD player) Set top box 6 En

9 Analog connection of an external device (game console) You can connect an external device, such as a game console or TV that does not have an optical output, to the ANALOG input jacks of the sound bar. Wireless connection with the subwoofer When the power cables of the sound bar and subwoofer are connected to AC wall outlets (p.6) and the sound bar is turned on, the sound bar and subwoofer are connected automatically. When the connection is complete, the SUBWOOFER indicator on the sound bar lights up and the sound bar is ready for playback. Subwoofer indicator: Lights up RCA stereo cable (etc.) (commercially available) HINT When the sound bar is turned on for the first time, if the SUBWOOFER indicator on the sound bar does not light up, see Pairing the sound bar and subwoofer manually (p.19) and connect the sound bar and subwoofer manually. Once connected, the sound bar operates with the same subwoofer from the next time it is turned on. Game console (etc.) NOTE Make sure the left (L) and right (R) channels are connected correctly. Select the ANALOG key on the remote control for the input source. En 7

10 Operations Indicators The indicators on the front panel flash or light up, to indicate the operation and setting status. In this manual, illustrations of the nine in-line indicators are used for explanation. : Off : Lights up : Flashes (Example: When the STATUS indicator flashes and the TV indicator lights up) Input keys 1 Select an input source to be played back. TV...TV audio BD/DVD...Audio from a device connected to the BD/DVD input jack ANALOG...Audio from a device connected to the ANALOG input jack BLUETOOTH...Audio from a Bluetooth connected device The indicator for the selected input source lights up. (Example: when TV is selected) HINT To play audio of the playback device connected to the TV or to watch videos of the playback device, set the TV s input source to the playback device. For details on Bluetooth connection, refer to Listening to the sound from a Bluetooth device (p.10). : Keys that require pressing for more than 3 seconds BLUETOOTH STANDBY, SUBWOOFER PAIRING, AUDIO DELAY, LEARN, REPEATER Remote control signal transmitter Transmits infrared signals. SUBWOOFER keys (+/ ) Adjust the volume of the subwoofer. 2 Volume down ( ) Volume up (+) VOLUME keys (+/ ) Adjust the volume of the sound bar. Volume down ( ) Volume up (+) LEARN key Sets the sound bar to the TV s remote control learning mode (p.12). REPEATER key Enables/disables the TV Remote Repeater function (p.14). 3 8 En

11 (power) key Turns on or off (standby) the sound bar. The STATUS indicator on the sound bar Green (turned on) Red (Bluetooth standby) (p.11) Off (turned off) The STATUS indicator on the subwoofer Green (turned on) Red (turned off) BLUETOOTH STANDBY key Enables/disables the Bluetooth standby mode (p.11). SUBWOOFER PAIRING key Performs pairing between the sound bar and subwoofer (p.19). SURROUND and STEREO keys Switch between surround and stereo (2 channel) playback. When surround playback is selected, you can enjoy a realistic sound effect using Yamaha s exclusive AIR SURROUND XTREME. SURROUND Lights up (surround playback) STEREO Off (stereo playback) HINT When 2 channel stereo signals are played in surround, the PLII indicator lights up. Lights up (Dolby Pro Logic II) 4 5 CLEAR VOICE key Enables/disables the clear voice function. When this function is enabled, you can enjoy clear voice sounds while watching movies, TV dramas, news programs or sports programs. Flash 3 times (enabled), flash once (disabled) UNIVOLUME key Enables/disables the UniVolume function. When this function is enabled, consistent volume is maintained when inputs or sound sources switch. Flash 3 times (enabled), flash once (disabled) HINT The UniVolume function is automatically disabled when BLUETOOTH is selected as the input source. AUDIO DELAY key Adjusts the audio delay to synchronize the sound with the video when the video image on the TV may seem delayed with respect to the sound. Follow the procedure below to adjust the audio delay. 1 Hold down the AUDIO DELAY key for more than 3 seconds. The left most indicator flashes. 2 Press the SUBWOOFER (+/ ) key to adjust the audio delay. Pressing the SUBWOOFER (+) key delays the audio output timing. ( ) (+) 3 To finish the adjustment, press the AUDIO DELAY key. HINT The adjustment will be finished automatically if no operations are performed for 20 seconds. BASS EXTENSION key Enables/disables the bass extension function. When this function is enabled, you can enjoy powerful sound during surround playback through Yamaha s exclusive bass boost technology. Flash 3 times (enabled), flash once (disabled) MUTE key Mutes the audio output. Press the key again to unmute. Decoder indication Flash (on mute) 6 7 The sound bar supports the following audio signals. You can check the type of the input audio signal by the color of the indicator. Green (Dolby Digital), Red (DTS Digital Surround) Off (PCM) En 9

12 Listening to the sound from a Bluetooth device You can play back wirelessly from Bluetooth devices, such as smartphones or digital music players. See also the operating manual of the Bluetooth device for more details. Bluetooth devices Pairing a Bluetooth device with the sound bar When connecting to a Bluetooth device for the first time, pairing between the device and sound bar is required. Pairing is necessary for each Bluetooth device you use. Once pairing with a device is completed, subsequent connection with that device will not require pairing. 1 Press the BLUETOOTH key on the sound bar s remote control to select Bluetooth as the input source. The BLUETOOTH indicator on the front panel lights up in green. Lights up 2 Turn on the Bluetooth function of the device to be paired, and perform pairing. The operation varies depending on the device. Refer to the operation manual of the device. 3 Select YAS-203 Yamaha in the Bluetooth device list on the device. If a passkey (PIN) is required, enter the number Perform the following steps to use a Bluetooth device with the sound bar. For the first Bluetooth connection For subsequent Bluetooth connection Pairing a Bluetooth device with the sound bar Playing back audio from a Bluetooth device on the sound bar NOTE When pairing is completed, or a completion message appears on the device. Perform pairing with the Bluetooth device and sound bar within 10 meters (33 ft) of each other. Up to eight Bluetooth devices can be paired with the sound bar. If a ninth device is paired, the oldest pairing information is deleted. If pairing information for a device is deleted, to use that device again, pairing of the device is required again. If a Bluetooth device is already connected to the sound bar, terminate that Bluetooth connection (p.11), then perform pairing with the new device. Refer to Bluetooth (p.18) in Troubleshooting if pairing cannot be achieved. 10 En

13 Playing back audio from a Bluetooth device on the sound bar 1 With the sound bar turned on, press the BLUETOOTH key on the sound bar s remote control to select Bluetooth as the input source. The BLUETOOTH indicator on the front panel lights up in green. Lights up 2 Turn on the Bluetooth function of the device. When Bluetooth connection is made correctly, the BLUETOOTH indicator of the sound bar flashes 3 times. Using the Bluetooth standby mode The Bluetooth standby mode allows you to turn on (or off) the sound bar automatically, that interlocked by the operation of the Bluetooth device. 1 With the sound bar turned on, hold down the BLUETOOTH STANDBY key on the sound bar s remote control for more than 3 seconds. Holding down the BLUETOOTH STANDBY key for 3 seconds each time toggles the mode between enabled and disabled. Flash 3 times (enabled), flash once (disabled) When the Bluetooth standby mode is enabled and the sound bar is turned off, the STATUS indicator lights up in red. (Bluetooth standby) Flashes 3 times 3 Play back a song on the device. Lights up (red) Functions available on Bluetooth devices with Bluetooth standby mode enabled Power on interlock function (when the sound bar is turned off) When Bluetooth connection is made on the device, the sound bar will turn on and will be ready to play back sound from the device. NOTE Perform Bluetooth connection with the device and sound bar within 10 meters (33 ft) of each other. It may be necessary to select YAS-203 Yamaha in the Bluetooth device list again, in the event that a connection problem occurs. You may have to change the output setting to output audio to the sound bar, depending on the Bluetooth device you are using. Adjust the volume level of the Bluetooth device as required. If a Bluetooth device is already connected to the sound bar, terminate that Bluetooth connection, then connect with the new device. Terminating Bluetooth connection Bluetooth connection is terminated in the following cases. When the sound bar is turned on and the Bluetooth connection is terminated, the BLUETOOTH indicator flashes once. Power off interlock function (when the sound bar is turned on) The sound bar will be turned off when Bluetooth connection is terminated on a Bluetooth device. (Only when BLUETOOTH is selected as the input source.) Using the HOME THEATER CONTROLLER application By installing the dedicated free application HOME THEATER CONTROLLER to a Bluetooth device, such as a smartphone, you can perform various operations easily and conveniently with the Bluetooth device. (Setting items: basic operation, sound-field, sound adjustments) For details on HOME THEATER CONTROLLER, see the product information on our website. The Bluetooth function is turned off on the compatible device. The BLUETOOTH key on the sound bar s remote control is pressed for more than 3 seconds. The sound bar is turned off. En 11

14 Settings Programming the sound bar with the TV s remote control (TV s remote control learning function) Once you program the sound bar, you can control it with your TV s remote control for functions such as turning on/off the TV and sound bar simultaneously, or volume up/ down and muting/unmuting of the sound bar. 4-2 While pointing your TV s remote control at the remote control sensor, hold down the mute key for more than 1 second twice or three times. Approx. 30 cm (1 ft) TV s remote control This function is available only when your TV s remote control uses IR (infrared) signal. An RF (Radio Frequency) remote control will not work. If you want to use a cable or satellite set top box s remote control to operate the sound bar, use your original TV s IR (infrared) remote control to program the sound bar, then use the set top box s remote control to operate. If by changing the volume of the sound bar the TV s volume also changes, set the TV s volume to minimum, or disable speaker output. 1 Turn off the TV. 2 Turn off the sound bar. 3 Hold down the LEARN key on the sound bar s remote control for more than 3 seconds to set the sound bar to the learning mode. When the sound bar is in the learning mode, the indicators on the front panel flash as shown below. Result Bleep/buzzer Indicators Successfully learned Failed to learn * Repeat from Step 4-1. Hold down (more than 1 second) Once Twice Release (more than 1 second) Lights up Hold down (more than 1 second) Flash Release (...) 5 Teach the sound bar the Volume ( ) code of the TV s remote control. 5-1 Press VOLUME ( ) on the front panel of the sound bar. NOTE Steps 4 to 7 require only the TV s remote control and the keys on the front panel of the sound bar. The remote control of the sound bar is not necessary. If the sound bar has already learned functions, the following indicators light up. Mute: BD/DVD, Volume ( ): ANALOG, Volume (+): BLUETOOTH, Power: SURROUND 4 Teach the sound bar the Mute code of the TV s remote control. 4-1 Press MUTE on the front panel of the sound bar. 5-2 While pointing your TV s remote control at the remote control sensor, hold down the volume ( ) key for more than 1 second twice or three times. Result Bleep/buzzer Indicators Successfully learned Once Lights up Failed to learn * Repeat from Step 5-1. Twice Flash 12 En

15 6 Teach the sound bar the Volume (+) code of the TV s remote control. 6-1 Press VOLUME (+) on the front panel of the sound bar. 6-2 While pointing your TV s remote control at the remote control sensor, hold down the volume (+) key for more than 1 second twice or three times. Result Bleep/buzzer Indicators Clearing all programmed functions 1 With the sound bar turned off, hold down the LEARN key on the sound bar s remote control for more than 3 seconds (for entering the learning mode). When the sound bar is in the learning mode, the indicators on the front panel flash as shown below. Successfully learned Once Lights up Failed to learn * Repeat from Step 6-1. Twice Flash 2 Hold down INPUT on the front panel of the sound bar for more than 3 seconds. 7 Teach the sound bar the Power code of the TV s remote control. 7-1 Press (power) on the front panel of the sound bar. 7-2 While pointing your TV s remote control at the remote control sensor, hold down the power key for more than 1 second twice or three times. Result Bleep/buzzer Indicators If the clearing is completed, you will hear the bleep sound three times. 3 Press the LEARN key on the sound bar s remote control. Flashes in red (cleared) Successfully learned Once Lights up Failed to learn * Repeat from Step 7-1. Twice Flash 8 To finish the learning mode, press the LEARN key on the sound bar s remote control. This completes the necessary settings. Now you can operate the sound bar with the TV s remote control s mute key, volume keys, or power key. HINT The learning mode will be finished automatically if no operations are performed for 5 minutes. Set the TV volume to minimum. When you turn up the volume of the sound bar with the TV s remote control, the volume of the TV may be turned up at the same time. In this case, follow Step 3 in Connections (p.6) to change the TV setting. You can press the (power) key on the sound bar s remote control to finish learning mode. En 13

16 Sending the TV s remote signal through the sound bar (TV Remote Repeater function) When the TV Remote Repeater function is enabled, the sound bar relays the TV s remote signal received by the front sensor to the rear transmitter. This function should be enabled when you place the sound bar in front of your TV and you cannot operate your TV with the TV s remote control. This function is available only when your TV s remote control uses infrared signals. IR flasher for TV Remote Repeater TV s remote control TV s remote control sensor 1 Turn on the sound bar. 2 Hold down the REPEATER key on the sound bar s remote control for more than 3 seconds to enable/disable the TV Remote Repeater function. Flash 3 times (enabled), flash once (disabled) This completes the necessary settings. When the TV Remote Repeater function is enabled, you can operate your TV from the TV s remote control via the sound bar. HINT The TV Remote Repeater function is disabled by default. If the power cable of the sound bar is connected to an AC wall outlet and when the TV Remote Repeater function is enabled, the function is usable even when the sound bar is turned off. If you have made the sound bar learn the volume (+) operation (p.13), the volume of the TV may be turned up when you turn up the volume of the sound bar with the TV s remote control. In this case, follow Step 3 in Connections (p.6) to change the TV setting. You can check the status of the TV Remote Repeater function by the SURROUND indicator when turning on the sound bar. Setting the auto power standby function By enabling the auto power standby function, you can avoid forgetting to turn off the sound bar after use, or if you fall asleep while watching TV. NOTE When the auto power standby function is enabled and one of the following conditions is met, the sound bar will automatically turn off. No operation for 8 hours No audio input and no operations for 20 minutes when BLUETOOTH is selected as the input source. 1 With the sound bar turned off, hold down the MUTE key on the sound bar s remote control for more than 3 seconds to enable/disable the auto power standby function. You can check the status of the auto power standby function with the TV indicator when turning on the sound bar. HINT Initial setting varies depending on the country or region. U.K. and Europe models: enabled Other models: disabled Initializing the sound bar Off (enabled), lights up (disabled) Follow the procedure below to initialize the sound bar. 1 Turn off the sound bar. 2 Hold down (power) on the front panel of the sound bar for more than 3 seconds. Off (enabled), lights up (disabled) Flash (initialized) 14 En

17 Troubleshooting Refer to the table below when the sound bar does not function properly. If the problem you are experiencing is not listed below or if the instructions below do not help, turn off the sound bar, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. First, check the following: A The power cables of the sound bar, subwoofer, TV and playback devices (such as BD players) are connected to AC wall outlets securely. B The sound bar, TV and playback devices (such as BD players) are turned on. C The connectors of each cable are securely inserted in to jacks on each device. Power and system Problem Cause Remedy The power turns off suddenly. The power cannot be turned on. The auto power standby function worked. When the auto power standby function is enabled and one of the following conditions is met, the sound bar will automatically turn off. - No operation for 8 hours - No audio input and no operations for 20 minutes when BLUETOOTH is selected as the input source. The protection circuitry has been activated. (The STATUS indicator on the front panel of the sound bar flashes.) Bluetooth connection is terminated on a Bluetooth device when the Bluetooth standby mode is enabled. The protection circuitry has been activated three times consecutively. (If you try to turn on the power in this condition, the STATUS indicator on the front panel of the sound bar flashes.) Turn on the sound bar again. To stop the sound bar from turning off automatically, disable the auto power standby function (p.14). After confirming that all connections are made properly, turn on the sound bar again. If the power still turns off suddenly or cannot be turned on, unplug the power cable from the AC wall outlet and contact the nearest authorized Yamaha dealer or service center. Disable the Bluetooth standby mode (p.11). To protect the product, the power cannot be turned on. Unplug the power cable from the AC wall outlet and contact the nearest authorized Yamaha dealer or service center. The sound bar is not responding correctly. The sound bar operates by itself. TV s 3D glasses do not work. Audio The internal microcomputer is frozen, due to an external electric shock (such as lightning or excessive static electricity) or to a drop in the power supply voltage. Another Bluetooth device is being operated nearby. The sound bar is blocking the 3D glasses transmitter of your TV. Hold down (power) on the front panel of the sound bar for more than 10 seconds to reboot it. (If the problem persists, disconnect the power cable from the AC wall outlet and plug it again.) Terminate Bluetooth connection of the sound bar (p.11). Check the position of the 3D glasses transmitter of your TV and adjust the position of the sound bar. Remove the stands of the sound bar if they are attached (p.5). Problem Cause Remedy No sound. Another input source is selected. Select an appropriate input source (p.8). The mute function is activated. Cancel the mute function (p.9). The volume is too low. Turn up the volume (p.8). The power cables of the sound bar and subwoofer are not connected properly. Make sure that power cables of the sound bar and subwoofer are connected to AC wall outlets securely (p.6). En 15

18 No sound is coming from the subwoofer. (The SUBWOOFER indicator on the front panel of the sound bar is flashing.) The sound from the subwoofer is interrupted. (The SUBWOOFER indicator on the sound bar flashes when the sound is interrupted.) The subwoofer is not connected to an AC wall outlet. (The STATUS indicator on the subwoofer is not lit.) The sound bar and subwoofer are not connected due to a bad wireless communication status. (The STATUS indicator on the subwoofer continues to be lit in red or flash in green.) The sound bar and subwoofer are not paired. (The STATUS indicator on the subwoofer is flashing or lit in red.) The protection circuitry in the subwoofer has been activated. (The STATUS indicator on the subwoofer is lit in orange.) The connection between the sound bar and subwoofer is interrupted due to a bad wireless communication status. (The STATUS indicator on the subwoofer flashes in green when the sound is interrupted.) Plug in the power cable of the subwoofer to an AC wall outlet. Move the subwoofer closer to the sound bar. If the situation does not improve, move the subwoofer to a location with better communication. If the communication between the sound bar and subwoofer is obstructed by a metallic object or another object, change the position of the sound bar and subwoofer or change the installation location of the subwoofer. If there is a device (microwave oven, wireless LAN, etc.) that emits radio frequency signals, move the sound bar and subwoofer away from the device. Perform the pairing between the sound bar and subwoofer (p.19). If the SUBWOOFER indicator on the sound bar still does not light up in green after the pairing is performed, a malfunction might have occurred. Unplug the power cables from the AC wall outlets and contact the nearest authorized Yamaha dealer or service center. To protect the product, the power of the subwoofer cannot be turned on. Unplug the power cable from the AC wall outlet and contact the nearest authorized Yamaha dealer or service center. Move the subwoofer closer to the sound bar. If the situation does not improve, move the subwoofer to a location with better communication. If the communication between the sound bar and subwoofer is obstructed by a metallic object or another object, change the position of the sound bar and subwoofer or change the installation location of the subwoofer. If there is a device (microwave oven, wireless LAN, etc.) that emits radio frequency signals, move the sound bar and subwoofer away from the device. No sound is coming from the subwoofer or the sound is small. (The SUBWOOFER indicator on the sound bar is lit.) The volume decreases when the sound bar is turned on. No surround effect. Noise is heard. The volume is too low. The front side of the subwoofer is blocked. The playback source does not contain low-frequency signals. The protection circuitry in the subwoofer has been activated. (The STATUS indicator on the subwoofer is lit in orange.) The automatic volume adjustment function worked. To prevent excessive loudness, the sound bar automatically controls its volume within a certain level when the sound bar is turned on. Stereo playback is selected. The volume is too low. The TV or playback device is set to output 2 channel audio (such as PCM) only. The audio is output from the TV built-in speakers. The playback source does not contain surround audio. The sound bar is too close to another digital or high-frequency device. Turn up the volume of the subwoofer (p.8). Clear the area around the front side and the port of the subwoofer. Play back a sound source containing low-frequency signals, and confirm that the sound is output from the subwoofer. To protect the product, the power of the subwoofer cannot be turned on. Unplug the power cable from the AC wall outlet and contact the nearest authorized Yamaha dealer or service center. If necessary, turn up the volume (p.8). Select surround playback (p.9). Turn up the volume (p.8). Change the digital audio output setting on the TV or playback device to Dolby Digital or BitStream. Set the TV volume to minimum (p.6). Play back a source that contains audio recorded in surround. Move those devices away from the sound bar. 16 En

19 Remote control Problem Cause Remedy The sound bar cannot be controlled using the remote control. The TV cannot be controlled using the TV s remote control. The sound bar is out of the operating range. The batteries are weak. The remote control sensor of the sound bar is exposed to direct sunlight or strong lighting. The remote control sensor of the TV is blocked by the sound bar. Use the remote control within the operating range (p.2). Replace with new batteries (p.2). Adjust the lighting angle, or reposition the sound bar. Use the TV Remote Repeater function (p.14) or remove the stands of the sound bar if they are attached so that the remote control sensor of the TV is not blocked (p.5). Enable the TV Remote Repeater function (p.14). The TV Remote Repeater function cannot be used in this case. Adjust the position of the sound bar so that the remote control sensor of the TV is not blocked by the sound bar and use the TV s remote control to operate the TV. Move the sound bar away from the TV more than 50 mm (2") (p.5). If necessary, attach or remove the stands of the sound bar to adjust height for the IR flasher (for TV Remote Repeater) of the sound bar positioning in front of the remote control sensor of the TV (p.5). Remove the obstacle between the sound bar and TV. The sound bar does not learn TV s remote control operations. The TV s remote control key was not held down long enough. The TV s remote control does not use infrared signals. (Some remote controls may not work even if it uses infrared signals.) The position where you operated the TV s remote control is not appropriate. The batteries of the TV s remote control are weak. The remote control sensor of the sound bar is exposed to direct sunlight or strong lighting. The transmission of the remote control signal was disturbed by the TV screen light. Audio output is enabled on the TV. Hold down the key for more than 1 second twice or three times (p.12). The TV s remote control learning function cannot be used in this case. Use the sound bar s remote control to operate the sound bar. Operate the TV s remote control at the appropriate position (p.12). Replace with new batteries. Adjust the lighting angle, or reposition the sound bar. The TV cannot be controlled by using the TV Remote Repeater function. The TV Remote Repeater function is disabled. The TV s remote control does not use infrared signals. (Some remote controls may not work even if it uses infrared signals.) The sound bar and TV are too close or too far from one another. There is any obstacle (such as cables) between the sound bar and TV. TV is not receiving the remote control signal well since the signals from the TV s remote control and IR flasher (for TV Remote Repeater) of the sound bar are interfering. Disable the TV Remote Repeater function (p.14). Sound is coming from the TV when the sound bar volume is turned up with the TV s remote control. (when TV s remote control learning function is used) The power of the sound bar and of the TV switch in the opposite direction. (For example, the TV is turned off if the sound bar is turned on.) (when TV s remote control learning function is used) The power of the TV was on when you performed the learning operation. Turn off the TV and perform the learning operation again (p.12). Change the TV setting to disable the TV speaker output. If a setting to disable the speaker output is not available on your TV, try the following methods. - Connect headphones to the headphone jack on the TV. - Set the TV volume to minimum. Press the power key on the TV and (power) on the front panel of the sound bar to turn them on and then press the power key on the TV s remote control to turn them off. En 17

20 Bluetooth Problem Cause Remedy Cannot make the sound bar paired Bluetooth is not selected as the input source. Select Bluetooth as the input source. with the The device does not support Perform pairing operations with a Bluetooth A2DP. device which supports A2DP. device. A Bluetooth adaptor, etc., that you want to pair with the sound bar has a password other than Use a Bluetooth adaptor, etc., whose password is No sound is produced or the sound is interrupted during playback. The Bluetooth connection of the sound bar with the device is disconnected. Bluetooth is not selected as the input source. The sound bar and device are too far apart. There is a device (microwave oven, wireless LAN, etc.) that outputs signals in the 2.4 GHz frequency band nearby. Perform Bluetooth connection operations again (p.10). Select Bluetooth as the input source. Move the device closer to the sound bar. Move the sound bar and subwoofer away from the device that is emitting radio frequency signals. The sound bar and device are too far apart. There is a device (microwave oven, wireless LAN, etc.) that outputs signals in the 2.4 GHz frequency band nearby. Another Bluetooth device is connected. Move the device closer to the sound bar. Move the sound bar away from the device that is emitting radio frequency signals. Terminate current Bluetooth connection, and perform pairing with the new device. The device is not set to send Bluetooth audio signals to the sound bar. Playback on the device has not been performed. The device s volume is set to minimum. Change the audio output setting and connection setting on the device. Perform playback on the device. Turn up the volume level. Cannot make a Bluetooth connection. Another Bluetooth device is connected. The sound bar cannot make multiple Bluetooth connections. Terminate current Bluetooth connection, and make connection for the desired device. More than nine devices are paired and the oldest pairing information is deleted. Perform pairing again. The sound bar can retain pairing information for up to eight devices. When pairing a ninth device, the oldest pairing information will be deleted. 18 En

21 Pairing the sound bar and subwoofer manually 1 With the sound bar turned on, hold down the SUBWOOFER PAIRING key on the sound bar s remote control for more than 3 seconds. The SUBWOOFER indicator on the front panel of the sound bar flashes rapidly. 2 Within 30 seconds, push the SUBWOOFER PAIRING button on the rear panel of the subwoofer for more than 3 seconds with a tapered object such as a hairpin. The STATUS indicator on the rear panel of the subwoofer flashes rapidly in green. When pairing is complete and the sound bar and subwoofer are connected, the SUBWOOFER indicator on the front panel of the sound bar lights up. If the SUBWOOFER indicator on the sound bar does not light up even after performing the above operation, see Troubleshooting (p.15). HINT Pairing is the operation where the sound bar and subwoofer decide the device to connect to. En 19

22 Specifications Item Amplifier Section Speaker Section Decoder Input Jacks Wireless subwoofer Bluetooth Maximum Rated Output Power Type Sound bar (YAS-CU203) Front L/R 50 W x 2 ch Acoustic suspension type (Non-magnetic shielding type) Subwoofer (NS-WSW41) Dynamic power 100 W Advanced Yamaha Active Servo Technology (Magnetic shielding type) Driver 5.5 cm (2-1/8") cone x 2 16 cm (6-1/2") cone Frequency Response 150 Hz to 22 khz 35 Hz to 150 Hz Impedance 6 Ω 5.5 Ω Supported audio signal (TV, BD/ DVD) PCM (2ch) Dolby Digital DTS Digital Surround Digital (Optical) 1 (TV) -- Digital (Coaxial) 1 (BD/DVD) -- Analog (RCA) 1 (ANALOG) -- Frequency band 2.4 GHz Transmission range 10 m ([33 ft] without interference) Bluetooth version Ver. 2.1+EDR -- Supported protocols A2DP, SPP -- Supported codecs SBC, aptx -- Wireless output Bluetooth Class 2 -- Maximum communication distance Supported content protection method 10 m ([33 ft] without obstructions) SCMS-T -- General Power Supply Power Consumption Standby Power Consumption Bluetooth standby power consumption Dimensions (W x H x D) * Specifications are subject to change without notice. U.S.A. and Canada models: AC 120 V, 60 Hz Taiwan model: AC V, 50/60 Hz China model: AC 220 V, 50 Hz Other models: AC V, 50/60 Hz 26 W 45 W 0.4 W 0.5 W x 79 x 121 mm (not including stands, default state) (34-7/8" x 3-1/8" x 4-3/4") 886 x 94 x 121 mm (including stands) (34-7/8" x 3-5/8" x 4-3/4") U.S.A. and Canada models: AC 120 V, 60 Hz U.K. and Europe models: AC 230 V, 50 Hz Taiwan model: AC 110 V, 60 Hz Korea model: AC 220 V, 60 Hz China model: AC 220 V, 50 Hz Australia model: AC 240 V, 50 Hz Asia model: AC V, 50/60 Hz U.S.A. and Canada models: 1.4 W U.K. and Europe models: 1.5 W Korea and Taiwan models: 1.2 W China model: 1.3 W Australia and Asia models: 1.7 W 290 x 292 x 316 mm (11-3/8" x 11-1/2" x 12-1/2") Thickness excluding speaker 65 mm (2-1/2") -- protrusions (thinnest part) Weight 2.9 kg (6.4 lbs) 8.1 kg (17.9 lbs) 20 En

23 This system is equipped with Yamaha s AIR SURROUND XTREME virtual sound technology that achieves superior positional, high-grade 7.1 channel surround sound using the sound bar and subwoofer. The subwoofer of this system employs Yamaha s exclusive bass control technology Advanced Yamaha Active Servo Technology II and has achieved high-quality low-frequency sound playback. UniVolume is a trademark of Yamaha Corporation. Bluetooth is a registered trademark of the Bluetooth SIG and is used by Yamaha in accordance with a license agreement. Bluetooth Bluetooth is a technology for wireless communication between devices within an area of about 10 meters (33 ft) employing the 2.4 GHz frequency band, a band which can be used without a license. Handling Bluetooth communications The 2.4 GHz band used by Bluetooth compatible devices is a radio band shared by many types of equipment. While Bluetooth compatible devices use a technology minimizing the influence of other components using the same radio band, such influence may reduce the speed or distance of communications and in some cases interrupt communications. The speed of signal transfer and the distance at which communications is possible differs according to the distance between the communicating devices, the presence of obstacles, radio wave conditions and type of equipment. Yamaha does not guarantee all wireless connections between this unit and devices compatible with Bluetooth function. Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double-d symbol are trademarks of Dolby Laboratories. For DTS patents, see Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks, and DTS Digital Surround is a trademark of DTS, Inc. DTS, Inc. All Rights Reserved CSR plc and its group companies. The aptx mark and the aptx logo are trade marks of CSR plc or one of its group companies and may be registered in one or more jurisdictions. Blu-ray Disc, Blu-ray, and the logos are trademarks of the Blu-ray Disc Association. En 21

TX-NR3030_BAS_Cs_ indd

TX-NR3030_BAS_Cs_ indd TX-NR3030 http://www.onkyo.com/manual/txnr3030/adv/cs.html Cs 1 2 3 Speaker Cable 2 HDMI OUT HDMI IN HDMI OUT HDMI OUT HDMI OUT HDMI OUT 1 DIGITAL OPTICAL OUT AUDIO OUT TV 3 1 5 4 6 1 2 3 3 2 2 4 3 2 5

More information

Logitech Wireless Combo MK45 English

Logitech Wireless Combo MK45 English Logitech Wireless Combo MK45 Setup Guide Logitech Wireless Combo MK45 English................................................................................... 7..........................................

More information

CANVIO_AEROCAST_CS_EN.indd

CANVIO_AEROCAST_CS_EN.indd 简 体 中 文...2 English...4 SC5151-A0 简 体 中 文 步 骤 2: 了 解 您 的 CANVIO AeroCast CANVIO AeroCast 无 线 移 动 硬 盘 快 速 入 门 指 南 欢 迎 并 感 谢 您 选 择 TOSHIBA 产 品 有 关 您 的 TOSHIBA 产 品 的 详 情, 请 参 阅 包 含 更 多 信 息 的 用 户 手 册 () 安

More information

K301Q-D VRT中英文说明书141009

K301Q-D VRT中英文说明书141009 THE INSTALLING INSTRUCTION FOR CONCEALED TANK Important instuction:.. Please confirm the structure and shape before installing the toilet bowl. Meanwhile measure the exact size H between outfall and infall

More information

OA-253_H1~H4_OL.ai

OA-253_H1~H4_OL.ai WARNINGS Note: Read ALL the following BEFORE using this product. Follow all Guidelines at all times while using this product. CAUTION This warning indicates possibility of personal injury and material

More information

01CP-WX3030WNetc_CO_ENG.indd

01CP-WX3030WNetc_CO_ENG.indd Data Video Projector User s Manual (Concise) ModelS: 8928A/8930A/8931WA/ 8933W Information in this Guide may change due to product improvements. To obtain the latest manuals, literature, and software please

More information

BC04 Module_antenna__ doc

BC04 Module_antenna__ doc http://www.infobluetooth.com TEL:+86-23-68798999 Fax: +86-23-68889515 Page 1 of 10 http://www.infobluetooth.com TEL:+86-23-68798999 Fax: +86-23-68889515 Page 2 of 10 http://www.infobluetooth.com TEL:+86-23-68798999

More information

LH_Series_Rev2014.pdf

LH_Series_Rev2014.pdf REMINDERS Product information in this catalog is as of October 2013. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check

More information

1.ai

1.ai HDMI camera ARTRAY CO,. LTD Introduction Thank you for purchasing the ARTCAM HDMI camera series. This manual shows the direction how to use the viewer software. Please refer other instructions or contact

More information

KDC-U5049 KDC-U4049 Made for ipod, and Made for iphone mean that an electronic accessory has been designed to connect specifically to ipod, or iphone,

KDC-U5049 KDC-U4049 Made for ipod, and Made for iphone mean that an electronic accessory has been designed to connect specifically to ipod, or iphone, KDC-U5049 KDC-U4049 Made for ipod, and Made for iphone mean that an electronic accessory has been designed to connect specifically to ipod, or iphone, respectively, and has been certified by the developer

More information

<4D6963726F736F667420576F7264202D2032303130C4EAC0EDB9A4C0E04142BCB6D4C4B6C1C5D0B6CFC0FDCCE2BEABD1A15F325F2E646F63>

<4D6963726F736F667420576F7264202D2032303130C4EAC0EDB9A4C0E04142BCB6D4C4B6C1C5D0B6CFC0FDCCE2BEABD1A15F325F2E646F63> 2010 年 理 工 类 AB 级 阅 读 判 断 例 题 精 选 (2) Computer mouse How does the mouse work? We have to start at the bottom, so think upside down for now. It all starts with mouse ball. As the mouse ball in the bottom

More information

Mixcder ShareMe 7 User Manual

Mixcder ShareMe 7 User Manual User s Manual MODEL:ShareMe7 Wireless Headphone Important safety instruction If used in the correct method, this design and production of this product can ensure your personal safety completely. However,

More information

1 2 3 Speaker Cable 2

1 2 3 Speaker Cable   2 TX-NR636 AV RECEIVER http://www.onkyo.com/manual/txnr636upg/adv/ct.html Ct 1 2 3 Speaker Cable http://www.onkyo.com/manual/txnr636upg/adv/ct.html 2 HDMI OUT HDMI IN HDMI OUT HDMI OUT HDMI OUT HDMI OUT

More information

pdf

pdf THE INSTLLING INSTRUCTION FOR CONCELED TNK Important instuction:.. Please confirm the structure and shape before installing the toilet bowl. Meanwhile measure the exact size H between outfall and infall

More information

HWS-BTA2W

HWS-BTA2W 2-689-456-81(1) Bluetooth Wireless Audio Adapter (Transmitter / Receiver) Operating Instructions GB CT HWS-BTA2W 2007 Sony Corporation WARNING To reduce the risk of fire or electric shock, do not expose

More information

Microsoft Word - template.doc

Microsoft Word - template.doc HGC efax Service User Guide I. Getting Started Page 1 II. Fax Forward Page 2 4 III. Web Viewing Page 5 7 IV. General Management Page 8 12 V. Help Desk Page 13 VI. Logout Page 13 Page 0 I. Getting Started

More information

* 1 * *1 *2 2

* 1 * *1 *2 2 * 1 * 2 1 2 *1 *2 2 3 1 2 7 bo 8 9 6 5 4 3 bn bm bl bk 1 2 3 * 4 5 6 7 8 9 bk bl p bq bp bm * bn bo bp bq * br br 8 . bs br bq bp bo 1234567 bo bnbm bl 8 9 bk 1 2 3 4 5 6 7 8 9 bk b bl bm bn bo bp

More information

AL-M200 Series

AL-M200 Series NPD4754-00 TC ( ) Windows 7 1. [Start ( )] [Control Panel ()] [Network and Internet ( )] 2. [Network and Sharing Center ( )] 3. [Change adapter settings ( )] 4. 3 Windows XP 1. [Start ( )] [Control Panel

More information

r_09hr_practical_guide_kor.pdf

r_09hr_practical_guide_kor.pdf PRACTICAL GUIDE TO THE EDIROL R-09HR 3 4 PRACTICAL GUIDE TO THE EDIROL R-09HR 5 Situation 1 6 1 2 3 PRACTICAL GUIDE TO THE EDIROL R-09HR WAV MP3 WAV 24 bit/96 khz WAV 16 bit/44.1 khz MP3 128 kbps/44.1

More information

WFC40810

WFC40810 9000086873 (PD 85 05 10) Operating and Installation Instructions Please read this specification carefully before you use the product. Any failure and losses caused by ignoring the above mentioned items

More information

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DV-SP302 Ct WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE

More information

Cube20S small, speedy, safe Eextremely modular Up to 64 modules per bus node Quick reaction time: up to 20 µs Cube20S A new Member of the Cube Family

Cube20S small, speedy, safe Eextremely modular Up to 64 modules per bus node Quick reaction time: up to 20 µs Cube20S A new Member of the Cube Family small, speedy, safe Eextremely modular Up to 64 modules per bus de Quick reaction time: up to 20 µs A new Member of the Cube Family Murrelektronik s modular I/O system expands the field-tested Cube family

More information

WARNING Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To reduce the risk of fire, do not cover the ventila

WARNING Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To reduce the risk of fire, do not cover the ventila The software of this system may be updated in the future. To find out details on any available updates, please visit the following URL. http://www.sony-asia.com/section/support Sound Bar Operating Instructions

More information

HT-S200F

HT-S200F Sound Bar Operating Instructions GB CT HT-S200F WARNING Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. For the AC adapter Labels for AC adapter Model No. and

More information

入學考試網上報名指南

入學考試網上報名指南 入 學 考 試 網 上 報 名 指 南 On-line Application Guide for Admission Examination 16/01/2015 University of Macau Table of Contents Table of Contents... 1 A. 新 申 請 網 上 登 記 帳 戶 /Register for New Account... 2 B. 填

More information

WVT new

WVT new Operating and Installation Instructions 5120 004601 (PD 84 09 25) Please read this specification carefully before you use the product. Any failure and losses caused by ignoring the above mentioned items

More information

國 立 政 治 大 學 教 育 學 系 2016 新 生 入 學 手 冊 目 錄 表 11 國 立 政 治 大 學 教 育 學 系 博 士 班 資 格 考 試 抵 免 申 請 表... 46 論 文 題 目 申 報 暨 指 導 教 授... 47 表 12 國 立 政 治 大 學 碩 博 士 班 論

國 立 政 治 大 學 教 育 學 系 2016 新 生 入 學 手 冊 目 錄 表 11 國 立 政 治 大 學 教 育 學 系 博 士 班 資 格 考 試 抵 免 申 請 表... 46 論 文 題 目 申 報 暨 指 導 教 授... 47 表 12 國 立 政 治 大 學 碩 博 士 班 論 國 立 政 治 大 學 教 育 學 系 2016 新 生 入 學 手 冊 目 錄 一 教 育 學 系 簡 介... 1 ( 一 ) 成 立 時 間... 1 ( 二 ) 教 育 目 標 與 發 展 方 向... 1 ( 三 ) 授 課 師 資... 2 ( 四 ) 行 政 人 員... 3 ( 五 ) 核 心 能 力 與 課 程 規 劃... 3 ( 六 ) 空 間 環 境... 12 ( 七 )

More information

您 對 本 產 品 的 選 擇 充 分 顯 示 了 您 對 音 響 設 備 的 精 通, 我 們 十 分 感 謝 您 的 惠 顧, 並 為 本 公 司 提 供 優 質 產 品 一 貫 傳 統 而 感 到 無 比 的 自 豪 為 使 您 的 裝 置 與 使 用 能 得 到 最 好 的 發 揮, 我 們

您 對 本 產 品 的 選 擇 充 分 顯 示 了 您 對 音 響 設 備 的 精 通, 我 們 十 分 感 謝 您 的 惠 顧, 並 為 本 公 司 提 供 優 質 產 品 一 貫 傳 統 而 感 到 無 比 的 自 豪 為 使 您 的 裝 置 與 使 用 能 得 到 最 好 的 發 揮, 我 們 NT-503 USB DAC/Network Player 關 於 此 機 器 的 網 路 功 能, 請 看 網 路 說 明 書 使 用 者 說 明 書 與 網 路 說 明 書 可 以 從 TEAC Global Site (http://www.teac-global.com/) 下 載 USB D/A 轉 換 器 / 網 路 播 放 機 使 用 說 明 書 欲 播 放 USB 快 閃 記 憶 體

More information

Microsoft Word - ChineseSATII .doc

Microsoft Word - ChineseSATII .doc 中 文 SAT II 冯 瑶 一 什 么 是 SAT II 中 文 (SAT Subject Test in Chinese with Listening)? SAT Subject Test 是 美 国 大 学 理 事 会 (College Board) 为 美 国 高 中 生 举 办 的 全 国 性 专 科 标 准 测 试 考 生 的 成 绩 是 美 国 大 学 录 取 新 生 的 重 要 依

More information

HC50246_2009

HC50246_2009 Page: 1 of 7 Date: June 2, 2009 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified by the vendor as:

More information

AS4610 Series QSG-EN_SC_TC R02.book

AS4610 Series QSG-EN_SC_TC R02.book Quick Start Guide 4/48-Port GE Data Center Switch AS460-0T AS460-0P AS460-54T AS460-54P. Unpack the Switch and Check Contents AS460-0T AS460-0P Note: The switch can also be installed on a desktop or shelf

More information

SHIMPO_表1-表4

SHIMPO_表1-表4 For servo motor ABLEREDUCER L Series Features Coaxial shaft series L series Helical gears contribute to reduce vibration and noise. Standard backlash is 5 arc-min, ideal for precision control. High rigidity

More information

Microsoft PowerPoint - ATF2015.ppt [相容模式]

Microsoft PowerPoint - ATF2015.ppt [相容模式] Improving the Video Totalized Method of Stopwatch Calibration Samuel C.K. Ko, Aaron Y.K. Yan and Henry C.K. Ma The Government of Hong Kong Special Administrative Region (SCL) 31 Oct 2015 1 Contents Introduction

More information

E15-3D1 1. Specifications Compact 4-Way Cassette type Model name MMU- AP0071MH2UL AP0091MH2UL AP0121MH2UL AP0151MH2UL AP0181MH2UL Cooling Capacity kbt

E15-3D1 1. Specifications Compact 4-Way Cassette type Model name MMU- AP0071MH2UL AP0091MH2UL AP0121MH2UL AP0151MH2UL AP0181MH2UL Cooling Capacity kbt E15-3D1 Compact 4-Way Cassette type MMU-AP0071MH2UL MMU-AP0091MH2UL MMU-AP0121MH2UL MMU-AP0151MH2UL MMU-AP0181MH2UL Contents 1. Specifications 2. Dimensions 3. Center of gravity 4. Piping diagram 5. Wiring

More information

1. 請 先 檢 查 包 裝 內 容 物 AC750 多 模 式 無 線 分 享 器 安 裝 指 南 安 裝 指 南 CD 光 碟 BR-6208AC 電 源 供 應 器 網 路 線 2. 將 設 備 接 上 電 源, 即 可 使 用 智 慧 型 無 線 裝 置 進 行 設 定 A. 接 上 電 源

1. 請 先 檢 查 包 裝 內 容 物 AC750 多 模 式 無 線 分 享 器 安 裝 指 南 安 裝 指 南 CD 光 碟 BR-6208AC 電 源 供 應 器 網 路 線 2. 將 設 備 接 上 電 源, 即 可 使 用 智 慧 型 無 線 裝 置 進 行 設 定 A. 接 上 電 源 1. 請 先 檢 查 包 裝 內 容 物 AC750 多 模 式 無 線 分 享 器 安 裝 指 南 安 裝 指 南 CD 光 碟 BR-6208AC 電 源 供 應 器 網 路 線 2. 將 設 備 接 上 電 源, 即 可 使 用 智 慧 型 無 線 裝 置 進 行 設 定 A. 接 上 電 源 B. 啟 用 智 慧 型 裝 置 的 無 線 Wi-Fi C. 選 擇 無 線 網 路 名 稱 "edimax.setup"

More information

Pneumonia - Traditional Chinese

Pneumonia - Traditional Chinese Pneumonia When you have pneumonia, the air sacs in the lungs fill with infection or mucus. Pneumonia is caused by a bacteria, virus or chemical. It is not often passed from one person to another. Signs

More information

Important Notice SUNPLUS TECHNOLOGY CO. reserves the right to change this documentation without prior notice. Information provided by SUNPLUS TECHNOLO

Important Notice SUNPLUS TECHNOLOGY CO. reserves the right to change this documentation without prior notice. Information provided by SUNPLUS TECHNOLO Car DVD New GUI IR Flow User Manual V0.1 Jan 25, 2008 19, Innovation First Road Science Park Hsin-Chu Taiwan 300 R.O.C. Tel: 886-3-578-6005 Fax: 886-3-578-4418 Web: www.sunplus.com Important Notice SUNPLUS

More information

Microsoft Word - 第四組心得.doc

Microsoft Word - 第四組心得.doc 徐 婉 真 這 四 天 的 綠 島 人 權 體 驗 營 令 我 印 象 深 刻, 尤 其 第 三 天 晚 上 吳 豪 人 教 授 的 那 堂 課, 他 讓 我 聽 到 不 同 於 以 往 的 正 義 之 聲 轉 型 正 義, 透 過 他 幽 默 熱 情 的 語 調 激 起 了 我 對 政 治 的 興 趣, 願 意 在 未 來 多 關 心 社 會 多 了 解 政 治 第 一 天 抵 達 綠 島 不 久,

More information

User’s Manual

User’s Manual SNAP 500 打 印 机 用 户 手 册 1 用 户 手 册 SNAP TM 500 打 印 机 2015 年 8 月 24 日 AVERY DENNISON Manual Edition 2.5 2 SNAP 500 打 印 机 用 户 手 册 WARNING This device complies with Part 15 of the FCC Rules. Operation is subject

More information

HC20131_2010

HC20131_2010 Page: 1 of 8 Date: April 14, 2010 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified by the vendor as:

More information

SHIMPO_表1-表4

SHIMPO_表1-表4 For servo motor ABLEREDUCER SSeries Coaxial shaft series Features S series Standard backlash is 3 arc-min, ideal for precision control. High rigidity & high torque were achived by uncaged needle roller

More information

5in1_eDVR_Manual_Chinese.cdr

5in1_eDVR_Manual_Chinese.cdr 02 English User Manual 29 User Manual Contents 2 5 6 7 8 9 10 11 12 14 17 18 19 20 21 22 23 24 25 26 27 Quick start Controls Accessories Minimum System Requirements Battery Charge Power On/Off LCM Indicator

More information

S325A 2

S325A 2 TX-NR609 S325A 2 ON/STANDBY ON/STANDBY POWER POWER ON/STANDBY POWER 3 2 2 3 3 * 4 VCR/DVR ON/STANDBY 69 5 * *2 *3*4 -*5 *5 *6 *7 *6 *6 *6 *8 *9 * *0 *9 6 * *2 *3 *4 *5 *6 *7 *8 *9 *0 *0 7 ON/STANDBY 22

More information

Microsoft Word - 3. Vitroefication_using_EMGP.docx

Microsoft Word - 3. Vitroefication_using_EMGP.docx EM GP 冷 冻 样 品 制 备 实 习 教 程 (Xiaojun Huang, Gang Ji) 每 位 演 示 及 带 领 学 员 实 习 EM GP 冷 冻 样 品 制 备 的 老 师 的 材 料 清 单 : 1)15 个 GIG 载 网 2) 冷 冻 样 品 Ferritin 或 Ribosome 3)EM GP 专 用 镊 子 1 把 4)1-10ul 移 液 器,1 把 ( 移 液 器

More information

CONGRATULATIONS ON YOUR PURCHASE OF OUR CAMERA This product has been carefully inspected through rigid quality control before shipment. With reasonabl

CONGRATULATIONS ON YOUR PURCHASE OF OUR CAMERA This product has been carefully inspected through rigid quality control before shipment. With reasonabl INSTRUCTIONS MANUAL SMOKE DETECTOR COLOR, B/W CCD CAMERA CONTENTS English / Chinese PREFACE SAFETY INSTRUCTIONS FUNCTION DESCRIPTION INSTALLATION SPECIFICATIONS PR0210SDE2 Thank you very much for purchasing

More information

HCD0174_2008

HCD0174_2008 Reliability Laboratory Page: 1 of 5 Date: December 23, 2008 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified

More information

Microsoft PowerPoint - STU_EC_Ch08.ppt

Microsoft PowerPoint - STU_EC_Ch08.ppt 樹德科技大學資訊工程系 Chapter 8: Counters Shi-Huang Chen Fall 2010 1 Outline Asynchronous Counter Operation Synchronous Counter Operation Up/Down Synchronous Counters Design of Synchronous Counters Cascaded Counters

More information

8260

8260 8260 2004 9 Lenovo 15 32 1 60 40 60 2 ... 6... 6... 7... 9... 11... 14... 15... 15... 16... 17 PictBridge... 18... 19... 19 Lenovo... 21 Lenovo... 23... 24... 25 Lenovo... 28... 29 3 ... 30... 30... 31...

More information

1

1 Application Chuck Instruction Manual Universal Ball Lock Power Chuck APPLICATION CHUCK PBL CHUCK (UNIVERSAL BALL LOCK POWER CHUCK) TABLE OF CONTENTS Keep this manual handy for easy reference as it will

More information

Microsoft Word - LR1122B-B.doc

Microsoft Word - LR1122B-B.doc UNISONIC TECHNOLOGIES CO., LTD LOW NOISE ma LDO REGULATOR DESCRIPTION The UTC is a typical LDO (linear regulator) with the features of High output voltage accuracy, low supply current, low ON-resistance,

More information

K7VT2_QIG_v3

K7VT2_QIG_v3 ............ 1 2 3 4 5 [R] : Enter Raid setup utility 6 Press[A]keytocreateRAID RAID Type: JBOD RAID 0 RAID 1: 2 7 RAID 0 Auto Create Manual Create: 2 RAID 0 Block Size: 16K 32K

More information

WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR PORTABLE CART WARNING S325A CT-2

WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR PORTABLE CART WARNING S325A CT-2 FR-N3X WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR PORTABLE CART WARNING S325A CT-2 CT-3 CLASS LASER PRODUCT CT-4 CT-5 6 mm mm 3 mm 6 5mm 2 CT-6 2 CT-7 2 3 0mm

More information

Preface This guide is intended to standardize the use of the WeChat brand and ensure the brand's integrity and consistency. The guide applies to all d

Preface This guide is intended to standardize the use of the WeChat brand and ensure the brand's integrity and consistency. The guide applies to all d WeChat Search Visual Identity Guidelines WEDESIGN 2018. 04 Preface This guide is intended to standardize the use of the WeChat brand and ensure the brand's integrity and consistency. The guide applies

More information

Microsoft Word - PZ series.doc

Microsoft Word - PZ series.doc 叠 层 片 式 铁 氧 体 磁 珠 P 系 列 Multilayer Chip Ferrite Bead P Series Operating Temp. : -4 ~ +8 特 征 FEATUES 内 部 印 有 银 电 极 的 叠 层 结 构, 铁 氧 体 屏 蔽 无 串 扰 Internal silver printed layers and magnetic shielded structures

More information

HC70245_2008

HC70245_2008 Reliability Laboratory Page: 1 of 6 Date: September 5, 2008 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified

More information

SA-DK2-U3Rユーザーズマニュアル

SA-DK2-U3Rユーザーズマニュアル USB3.0 SA-DK2-U3R 2007.0 2 3 4 5 6 7 8 System Info. Manual Rebuild Delete RAID RAID Alarm Rebuild Rate Auto compare Temp Management Load Default Elapse time Event Log 0 2 3 4 2 3 4 ESC 5

More information

Microsoft Word - HC20138_2010.doc

Microsoft Word - HC20138_2010.doc Page: 1 of 7 Date: April 26, 2010 WINMATE COMMUNICATION INC. 9 F, NO. 111-6, SHING-DE RD., SAN-CHUNG CITY, TAIPEI, TAIWAN, R.O.C. The following merchandise was submitted and identified by the vendor as:

More information

MODEL COLOR LIST UZ125D2 YMW GRAY YNF RED YRG BLUE 30H WHITE

MODEL COLOR LIST UZ125D2 YMW GRAY YNF RED YRG BLUE 30H WHITE MODEL COLOR LIST UZ125D2 YMW GRAY YNF RED YRG BLUE 30H WHITE MODEL COLOR LIST UZ125D2K K13 BLACK YRG BLUE YPK WHITE MODEL COLOR LIST UZ125X2 G22 Q05 GRAY ORANGE GREEN WHITE N28 W08 PREFACE When it becomes

More information

2015 Chinese FL Written examination

2015 Chinese FL Written examination Victorian Certificate of Education 2015 SUPERVISOR TO ATTACH PROCESSING LABEL HERE Letter STUDENT NUMBER CHINESE FIRST LANGUAGE Written examination Monday 16 November 2015 Reading time: 11.45 am to 12.00

More information

C o n t e n t s...7... 15 1. Acceptance... 17 2. Allow Love... 19 3. Apologize... 21 4. Archangel Metatron... 23 5. Archangel Michael... 25 6. Ask for

C o n t e n t s...7... 15 1. Acceptance... 17 2. Allow Love... 19 3. Apologize... 21 4. Archangel Metatron... 23 5. Archangel Michael... 25 6. Ask for Doreen Virtue, Ph.D. Charles Virtue C o n t e n t s...7... 15 1. Acceptance... 17 2. Allow Love... 19 3. Apologize... 21 4. Archangel Metatron... 23 5. Archangel Michael... 25 6. Ask for a Sign... 27 7.

More information

B _02_ch.indd

B _02_ch.indd KDC-X8016BT KDC-X8016BTL KDC-X7016 KDC-X7016L B64-4521-10/02 (MW) 2 KDC-X8016BT/ KDC-X8016BTL/ KDC-X7016/ KDC-X7016L 3 2 > > 1 2 3 4 5 6 AUX 7 8 9 10 11 12 13 14 1 2 3 4 5 6 7 8 9 4 10 38 11 12 13 14 4

More information

Microsoft PowerPoint - Aqua-Sim.pptx

Microsoft PowerPoint - Aqua-Sim.pptx Peng Xie, Zhong Zhou, Zheng Peng, Hai Yan, Tiansi Hu, Jun-Hong Cui, Zhijie Shi, Yunsi Fei, Shengli Zhou Underwater Sensor Network Lab 1 Outline Motivations System Overview Aqua-Sim Components Experimental

More information

4. 每 组 学 生 将 写 有 习 语 和 含 义 的 两 组 卡 片 分 别 洗 牌, 将 顺 序 打 乱, 然 后 将 两 组 卡 片 反 面 朝 上 置 于 课 桌 上 5. 学 生 依 次 从 两 组 卡 片 中 各 抽 取 一 张, 展 示 给 小 组 成 员, 并 大 声 朗 读 卡

4. 每 组 学 生 将 写 有 习 语 和 含 义 的 两 组 卡 片 分 别 洗 牌, 将 顺 序 打 乱, 然 后 将 两 组 卡 片 反 面 朝 上 置 于 课 桌 上 5. 学 生 依 次 从 两 组 卡 片 中 各 抽 取 一 张, 展 示 给 小 组 成 员, 并 大 声 朗 读 卡 Tips of the Week 课 堂 上 的 英 语 习 语 教 学 ( 二 ) 2015-04-19 吴 倩 MarriottCHEI 大 家 好! 欢 迎 来 到 Tips of the Week! 这 周 我 想 和 老 师 们 分 享 另 外 两 个 课 堂 上 可 以 开 展 的 英 语 习 语 教 学 活 动 其 中 一 个 活 动 是 一 个 充 满 趣 味 的 游 戏, 另 外

More information

Rotary Switch Catalogue

Rotary Switch Catalogue Rotary Switches RS300/400/500 Series Outline Our RS series embody the manufacturing history of our company. All series are sturdy and solid with high dependability designed for control units of plants,

More information

UTI (Urinary Tract Infection) - Traditional Chinese

UTI (Urinary Tract Infection) - Traditional Chinese UTI (Urinary Tract Infection) Urinary tract infection, also called UTI, is an infection of the bladder or kidneys. Urethra Kidney Ureters Bladder Vagina Kidney Ureters Bladder Urethra Penis Causes UTI

More information

Gerolor Motors Series Dimensions A,B C T L L G1/2 M8 G1/ A 4 C H4 E

Gerolor Motors Series Dimensions A,B C T L L G1/2 M8 G1/ A 4 C H4 E Gerolor Motors Series Size CC-A Flange Options-B Shaft Options-C Ports Features 0 0 12 12 1 1 0 0 2 2 31 31 0 0 SAE A 2 Bolt - (2) 4 Bolt Magneto (4) 4 Bolt Square (H4) 1.0" Keyed (C) 2mm Keyed (A) 1.0'

More information

Product Specification Chip Intel DSL6540 Thunderbolt 3 Controller Connectors 2 x Thunderbolt 3 ports (Thunderbolt 3 Port 1/Thunderbolt 3 Port 2), supp

Product Specification Chip Intel DSL6540 Thunderbolt 3 Controller Connectors 2 x Thunderbolt 3 ports (Thunderbolt 3 Port 1/Thunderbolt 3 Port 2), supp GC-ALPINE RIDGE Installation Guide/ 12WE6-ALPINER-10AR Product Specification Chip Intel DSL6540 Thunderbolt 3 Controller Connectors 2 x Thunderbolt 3 ports (Thunderbolt 3 Port 1/Thunderbolt 3 Port 2),

More information

Windows XP

Windows XP Windows XP What is Windows XP Windows is an Operating System An Operating System is the program that controls the hardware of your computer, and gives you an interface that allows you and other programs

More information

Gerotor Motors Series Dimensions A,B C T L L G1/2 M G1/ A 4 C H4 E

Gerotor Motors Series Dimensions A,B C T L L G1/2 M G1/ A 4 C H4 E Gerotor Motors Series Size CC-A Flange Options-B Shaft Options-C Ports Features 0 0 5 5 1 0 1 0 3 3 0 0 SAE A 2 Bolt - (2) 4 Bolt Magneto (4) 4 Bolt Square (H4) 1.0" Keyed (C) 25mm Keyed (A) 1.0' 6T Spline

More information

iml v C / 4W Down-Light EVM - pplication Notes. IC Description The iml8683 is a Three Terminal Current Controller (TTCC) for regulating the cur

iml v C / 4W Down-Light EVM - pplication Notes. IC Description The iml8683 is a Three Terminal Current Controller (TTCC) for regulating the cur iml8683-220v C / 4W Down-Light EVM - pplication Notes iml8683 220V C 4W Down Light EVM pplication Notes Table of Content. IC Description... 2 2. Features... 2 3. Package and Pin Diagrams... 2 4. pplication

More information

Ratings Specifications Outstanding Environmental Performance The body resin used by the BOXTC series is a reinforced PBT, which is PBT resin with high

Ratings Specifications Outstanding Environmental Performance The body resin used by the BOXTC series is a reinforced PBT, which is PBT resin with high Box Terminal TOGI s Box Terminals are the choicest terminal boxes for cable connection of industrial equipment, such as machine tool control, switching, power distribution and instrumentation equipment.

More information

iml88-0v C / 8W T Tube EVM - pplication Notes. IC Description The iml88 is a Three Terminal Current Controller (TTCC) for regulating the current flowi

iml88-0v C / 8W T Tube EVM - pplication Notes. IC Description The iml88 is a Three Terminal Current Controller (TTCC) for regulating the current flowi iml88-0v C / 8W T Tube EVM - pplication Notes iml88 0V C 8W T Tube EVM pplication Notes Table of Content. IC Description.... Features.... Package and Pin Diagrams.... pplication Circuit.... PCB Layout

More information

Building Technology Experience Center concept air conditioning concept heat pump special energy-saving techniques in hydraulics Concrete core conditio

Building Technology Experience Center concept air conditioning concept heat pump special energy-saving techniques in hydraulics Concrete core conditio Building Technology Experience Center concept air conditioning concept heat pump special energy-saving techniques in hydraulics Concrete core conditioning Initial situation Passive House Technology Experience

More information

WARNING Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To reduce the risk of fire, do not cover the ventila

WARNING Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To reduce the risk of fire, do not cover the ventila Sound Bar Operating Instructions GB CT The software of this system may be updated in the future. To find out details on any available updates, please visit the following URL. http://www.sony-asia.com/section/support

More information

REMOTEAIRPRO说明书中英文版

REMOTEAIRPRO说明书中英文版 REMOTE AIR PRO Product Manual Welcome to your new REMOTE AIR PRO REMOTE AIR PRO Whatʼs Included Instruction manual 1 Motor Installation The motor is mounted on 19 mm or 15 mm rods. For 15 mm rods use

More information

untitled

untitled LBS Research and Application of Location Information Management Technology in LBS TP319 10290 UDC LBS Research and Application of Location Information Management Technology in LBS , LBS PDA LBS

More information

2015年4月11日雅思阅读预测机经(新东方版)

2015年4月11日雅思阅读预测机经(新东方版) 剑 桥 雅 思 10 第 一 时 间 解 析 阅 读 部 分 1 剑 桥 雅 思 10 整 体 内 容 统 计 2 剑 桥 雅 思 10 话 题 类 型 从 以 上 统 计 可 以 看 出, 雅 思 阅 读 的 考 试 话 题 一 直 广 泛 多 样 而 题 型 则 稳 中 有 变 以 剑 桥 10 的 test 4 为 例 出 现 的 三 篇 文 章 分 别 是 自 然 类, 心 理 研 究 类,

More information

Male Circumcision - Traditional Chinese

Male Circumcision - Traditional Chinese Male Circumcision Male circumcision is the removal of the foreskin around the end of the penis. If you decide on circumcision, your baby s doctor will do it in the hospital s nursery. If your baby is small

More information

Male Circumcision - Simplified Chinese

Male Circumcision - Simplified Chinese Male Circumcision Male circumcision is the removal of the foreskin around the end of the penis. If you decide on circumcision, your baby s doctor will do it in the hospital s nursery. If your baby is small

More information

audiogram3 Owners Manual

audiogram3 Owners Manual USB AUDIO INTERFACE ZH 2 AUDIOGRAM 3 ( ) * Yamaha USB Yamaha USB ( ) ( ) USB Yamaha (5)-10 1/2 AUDIOGRAM 3 3 MIC / INST (XLR ) (IEC60268 ): 1 2 (+) 3 (-) 2 1 3 Yamaha USB Yamaha Yamaha Steinberg Media

More information

iml v C / 0W EVM - pplication Notes. IC Description The iml8683 is a Three Terminal Current Controller (TTCC) for regulating the current flowin

iml v C / 0W EVM - pplication Notes. IC Description The iml8683 is a Three Terminal Current Controller (TTCC) for regulating the current flowin iml8683-220v C / 0W EVM - pplication Notes iml8683 220V C 0W EVM pplication Notes Table of Content. IC Description... 2 2. Features... 2 3. Package and Pin Diagrams... 2 4. pplication Circuit... 3 5. PCB

More information

IP505SM_manual_cn.doc

IP505SM_manual_cn.doc IP505SM 1 Introduction 1...4...4...4...5 LAN...5...5...6...6...7 LED...7...7 2...9...9...9 3...11...11...12...12...12...14...18 LAN...19 DHCP...20...21 4 PC...22...22 Windows...22 TCP/IP -...22 TCP/IP

More information

徐汇教育214/3月刊 重 点 关 注 高中生异性交往的小团体辅导 及效果研究 颜静红 摘 要 采用人际关系综合诊断量表 郑日昌编制并 与同性交往所不能带来的好处 带来稳定感和安全感 能 修订 对我校高一学生进行问卷测量 实验组前后测 在 够度过更快乐的时光 获得与别人友好相处的经验 宽容 量表总分和第 4 项因子分 异性交往困扰 上均有显著差 大度和理解力得到发展 得到掌握社会技术的机会 得到 异

More information

Pin Configurations Figure2. Pin Configuration of FS2012 (Top View) Table 1 Pin Description Pin Number Pin Name Description 1 GND 2 FB 3 SW Ground Pin.

Pin Configurations Figure2. Pin Configuration of FS2012 (Top View) Table 1 Pin Description Pin Number Pin Name Description 1 GND 2 FB 3 SW Ground Pin. Features Wide 3.6V to 32V Input Voltage Range Output Adjustable from 0.8V to 30V Maximum Duty Cycle 100% Minimum Drop Out 0.6V Fixed 300KHz Switching Frequency 12A Constant Output Current Capability Internal

More information

CD DX Onkyo CD CD Cs

CD DX Onkyo CD CD Cs CD DX-7355... 2... 13... 15 Onkyo CD CD... 26 Cs 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. S3125A 13. 14. 15. A. B. C. D. E. F. 16. 17. 18. 20cm 8" 10cm 4" 10cm 4" Cs-2 1. 2. Onkyo 3. 4. AC230V 50Hz AC120V

More information

Chinese oil import policies and reforms 随 着 经 济 的 发 展, 目 前 中 国 石 油 消 费 总 量 已 经 跃 居 世 界 第 二 作 为 一 个 负 责 任 的 大 国, 中 国 正 在 积 极 推 进 能 源 进 口 多 元 化, 鼓 励 替 代

Chinese oil import policies and reforms 随 着 经 济 的 发 展, 目 前 中 国 石 油 消 费 总 量 已 经 跃 居 世 界 第 二 作 为 一 个 负 责 任 的 大 国, 中 国 正 在 积 极 推 进 能 源 进 口 多 元 化, 鼓 励 替 代 Chinese oil import policies and reforms SINOPEC EDRI 2014.8 Chinese oil import policies and reforms 随 着 经 济 的 发 展, 目 前 中 国 石 油 消 费 总 量 已 经 跃 居 世 界 第 二 作 为 一 个 负 责 任 的 大 国, 中 国 正 在 积 极 推 进 能 源 进 口 多 元 化,

More information

安 全 資 訊 重 要 安 全 指 示 1. 閱 讀 這 些 指 示 2. 保 留 這 些 指 示 3. 留 意 所 有 警 示 4. 遵 循 所 有 指 示 5. 不 要 在 水 源 附 近 使 用 該 產 品 6. 使 用 乾 布 擦 拭 機 器 7. 不 要 阻 塞 任 何 通 風 口 按 照

安 全 資 訊 重 要 安 全 指 示 1. 閱 讀 這 些 指 示 2. 保 留 這 些 指 示 3. 留 意 所 有 警 示 4. 遵 循 所 有 指 示 5. 不 要 在 水 源 附 近 使 用 該 產 品 6. 使 用 乾 布 擦 拭 機 器 7. 不 要 阻 塞 任 何 通 風 口 按 照 AV 收 音 擴 大 機 1 使 用 手 冊 安 全 資 訊 重 要 安 全 指 示 1. 閱 讀 這 些 指 示 2. 保 留 這 些 指 示 3. 留 意 所 有 警 示 4. 遵 循 所 有 指 示 5. 不 要 在 水 源 附 近 使 用 該 產 品 6. 使 用 乾 布 擦 拭 機 器 7. 不 要 阻 塞 任 何 通 風 口 按 照 用 戶 手 冊 來 安 裝 該 產 品 8. 不 要

More information

Bottle Feeding Your Baby - Simplified Chinese

Bottle Feeding Your Baby - Simplified Chinese Bottle Feeding Your Baby Bottle feeding with formula will meet your baby s food needs. Your doctor will help decide which formula is right for your baby. Never give milk from cows or goats to a baby during

More information

資料HDR作1-03 HDR技術動向

資料HDR作1-03 HDR技術動向 作 1-3 TV Platform Div. TV Platform Div. FHD () more UHD UHD (BT.2020) [cd/m 2 ] 10 9 10 8 10 6 10 4 10 2 10 0 10-2 10-4 10-6 () ~10 5 [cd/m 2 ] 10 9 10 8 10 6 10 4 10 2 10 0 10-2 10-4 10-6 2014 XDR/XDR-Pro

More information

IMPORTANT SAFETY INSTRUCTIONS / When using an electrical appliance, basic safety precautions should always be followed, including the following:read a

IMPORTANT SAFETY INSTRUCTIONS / When using an electrical appliance, basic safety precautions should always be followed, including the following:read a 1-NEEDLE, 3-THREAD OVERLOCK SEWING MACHINE MO-623 INSTRUCTION MANUAL IMPORTANT: READ ALL SAFETY REGULATIONS CAREFULLY AND UNDERSTAND THEM BEFORE USING YOUR SEWING MACHINE. RETAIN THIS INSTRUCTION MANUAL

More information

pdf

pdf 88% 84% OK 1 3 1.1 1.2 1.3 (1) (1) (1) 1/7/2013 (2) (3) (2) (2) 1/7/2013 (4) (5) (6) (7) (3) (4) (3) (4) (5) 1/7/2013 1/7/2013 1/7/2013 (6) 1/7/2013 2 (7) 1/9/2013 2.1 (8) 1/9/2013 (9) 1/12/2013 2.2 2.3

More information

Product Specification Chip Connectors Interface Data Transfer Rate Intel DSL5520 Thunderbolt 2 Controller 2 x Thunderbolt 2 ports (TBT 1/TBT 2), suppo

Product Specification Chip Connectors Interface Data Transfer Rate Intel DSL5520 Thunderbolt 2 Controller 2 x Thunderbolt 2 ports (TBT 1/TBT 2), suppo GC-Thunderbolt 2 Installation Guide/ 12WE6-TH2-10AR Product Specification Chip Connectors Interface Data Transfer Rate Intel DSL5520 Thunderbolt 2 Controller 2 x Thunderbolt 2 ports (TBT 1/TBT 2), supporting

More information

Applied Biosystems StepOne™ Real-Time PCR System Quick Reference Card for Installation

Applied Biosystems StepOne™ Real-Time PCR System Quick Reference Card for Installation Applied Biosystems StepOne Real-Time PCR System StepOne 系统安装 快速参考卡 本文档提供在并置布局中安装 StepOne 系统的简明指导 有关 完整步骤或独立安装步骤 请参阅 Applied Biosystems StepOne Real-Time PCR System 安装 联网和维护指南 目录 1. 安装准备........................................

More information

2005 5,,,,,,,,,,,,,,,,, , , 2174, 7014 %, % 4, 1961, ,30, 30,, 4,1976,627,,,,, 3 (1993,12 ),, 2

2005 5,,,,,,,,,,,,,,,,, , , 2174, 7014 %, % 4, 1961, ,30, 30,, 4,1976,627,,,,, 3 (1993,12 ),, 2 3,,,,,, 1872,,,, 3 2004 ( 04BZS030),, 1 2005 5,,,,,,,,,,,,,,,,, 1928 716,1935 6 2682 1928 2 1935 6 1966, 2174, 7014 %, 94137 % 4, 1961, 59 1929,30, 30,, 4,1976,627,,,,, 3 (1993,12 ),, 2 , :,,,, :,,,,,,

More information

Product Type Batteries (only) Circuit Breatkers & Load Protection Connection Devices Contactors Ethernet Switches, Stratix Switches I/O Modules; PLC N

Product Type Batteries (only) Circuit Breatkers & Load Protection Connection Devices Contactors Ethernet Switches, Stratix Switches I/O Modules; PLC N 1201 South Second Street Milwaukee, Wisconsin U.S.A. 53204 Tel 414-382-2000 1 July 2016 RE: China Restriction of Hazardous Substances (RoHS) Dear Customer, Rockwell Automation is committed to demonstrating

More information

Microsoft Word - KSAE06-S0262.doc

Microsoft Word - KSAE06-S0262.doc Stereo Vision based Forward Collision Warning and Avoidance System Yunhee LeeByungjoo KimHogi JungPaljoo Yoon Central R&D Center, MANDO Corporation, 413-5, Gomae-Ri, Gibeung-Eub, Youngin-Si, Kyonggi-Do,

More information

区 域 活 动 进 入 中 班 我 们 区 域 的 设 置 和 活 动 材 料 都 有 所 变 化, 同 时 也 吸 引 孩 子 们 积 极 的 参 与 学 习 操 作 区 的 新 材 料 他 们 最 喜 欢, 孩 子 们 用 立 方 块 进 行 推 理 操 作 用 扑 克 牌 进 行 接 龙 游

区 域 活 动 进 入 中 班 我 们 区 域 的 设 置 和 活 动 材 料 都 有 所 变 化, 同 时 也 吸 引 孩 子 们 积 极 的 参 与 学 习 操 作 区 的 新 材 料 他 们 最 喜 欢, 孩 子 们 用 立 方 块 进 行 推 理 操 作 用 扑 克 牌 进 行 接 龙 游 日 常 生 活 本 月 我 们 日 常 生 活 活 动 的 重 点 :1. 让 孩 子 养 成 良 好 的 生 活 习 惯, 注 重 生 活 细 节 如 : 在 换 好 鞋 子 后 能 将 鞋 子 整 齐 的 摆 放 进 鞋 架 坐 在 椅 子 上 换 鞋 正 确 的 收 放 椅 子 等 2 让 孩 子 有 自 我 照 顾 的 意 识 如, 让 孩 子 感 受 自 己 的 冷 热 并 告 知 老 师,

More information

東莞工商總會劉百樂中學

東莞工商總會劉百樂中學 /2015/ 頁 (2015 年 版 ) 目 錄 : 中 文 1 English Language 2-3 數 學 4-5 通 識 教 育 6 物 理 7 化 學 8 生 物 9 組 合 科 學 ( 化 學 ) 10 組 合 科 學 ( 生 物 ) 11 企 業 會 計 及 財 務 概 論 12 中 國 歷 史 13 歷 史 14 地 理 15 經 濟 16 資 訊 及 通 訊 科 技 17 視 覺

More information