Microsoft Word - TB RB_英文_ doc

Transcription

1 OPERATION AND MAINTENANCE MANUAL TB50L TB75L TB100L TB150L RB50L RB75L RB100L RB150L RB50P RB75P RB100P RB150P Attention! RB150L/P is belonging to high torque series. For safety consideration, please collaborate it with Auxiliary Arm (KP-AUXA). DC-TYPE Automatic Non Carbon-Brush Series KILEWS INDUSTRIAL CO., LTD. Y2F

2 NOTICE Metal Assembly Screwdrivers are designed for installing threaded fasteners in light industrial and appliance manufacturing applications. KILEWS is not responsible for customer modification of tools for applications on which KILEWS was not consulted. WARNING Important safety information enclosed. Read all these instructions before placing tool in service or operation this tool and save these instructions. It is the responsibility of the employer to place the information in this manual into the hands of the operator. Failure to observe the following warnings could result in injury. When using electric tools, Basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following:

3 Important Safety Rules WARNING! Read all instructions Failure to follow all instructions listed below may result in electric shock fire and/or serious injure. The term power tool in all of the warning listed below refer to your mains operated (corded) power tool or battery operated (cordless) power tool. SAVE THESE INSTRUCTIONS 1) Electrical Safety a) Keep work area clean and well lit. Cluttered and dark areas invite accidents. b) Do not operate power tools in explosive atmosphere, such as in the presence of flammable liquids, gases or dust. Power tools creat sparks which may ignite the dust of fumes.. c) Keep children, and bystanders away while operating a power tool. Distractions can cause you to lose control. 2) Electrical Safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Don t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord to carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.use of cord suitable for outdoor use reduces the risk of electric shock. 3) Personal Safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. Rubber gloves and non-skid footwear are recommended when working outdoors. c) Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents. d) Remove any adjusting keys or wrench before turning the power tool on. A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,clothing, and gloves away from moving parts. Loose clothes, jewellery, or long hair can be caught in moving parts g) Secure work.use clamps or a vice to hold the work. It is safer than using your hand and frees both hands to operate the tool. h) If devices are provided for the connection of dust extraction and collection facilitys, ensure these are connected and properly used. Use of these devices can reduce dust related hazards.

4 4) Power tool Use and Care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use power tool if switch does not turn it on or off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. Do not let visitors touch the tool or extension cord. All visitors should be kept away from work area. e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are cause by poorly maintained power tools. Inspect extension cords periodically and replace, if damaged. f) Keep cutting tools sharp and clean, Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tools, accessories and tool bits ect., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by qualified repair person using only indentical replacement parts, This will ensure that the safety of the power tool is maintained. Additional information shall be provide a) Instruction for putting into use 1. Setting-up or fixing power tool in a stable position as appropriate for power tools which can be mounted on a support. 2. Assembly 3. Connection to power supply, cabling, fusing, socket type and earthing requirements. 4. Illustrated description of functions. 5. Limitations on ambient conditions. 6. List of contents. b) Operating Instructions. 1. Setting and testing. 2. Tool changing. 3. Clamping of work. 4. Limits on size of work piece. 5. General instructions for use. c) Maintenance and servicing. 1. Regular cleaning, maintenance, and lubrication. 2. Servicing by manufacture or agent, list of addresses. 3. List of user-replaceable parts. 4. Special tools which may be required.

5 WARNING! DO NOT OPERATE THIS TOOL WITHOUT PROTECTIVE EARTH CONNECTED Grounding Instructions 1 This tool should be grounded while in use to protect the operator from electric shock. NOTICE! To ensure the grounding result, the grounding conductor of the power cord must be well connected with the grounding terminal of power facility. This tool is equipped with grounding conductors. The Green(or Green and Yellow)conductor in the Power Cord is the grounding wire. Never connect Green (or Green and Yellow) to a live terminal. The grounding wires in this tool can not only earth the electric leakage safely, but also can eliminate ESD-the electrostatic that tool occurred while in use. 2 The grounding is the most important task a user. Periodically, depends on the working condition and circumstance, for maintaining a good function the user has to check the grounding condition every 3~6 months by an electric meter and following simple steps; Set the Ohm meter to level R*100(Ohm). Touching 2 test rods ( + & - ) together and reset the meter to 0. Using the Red( + ) rod to touch the Grounding wire on the Plug of controller s cord, and the Black( - ) rod to the end of Bit Head. It stands for the grounding is normal if the meter is read as close as to 0. For getting a normal indication on the meter while in testing, need to press the test rods firmly to the testing objects. 3 The instrument QC of the tool is performed before the tool ex-factory. The grounding continuity test is conducted by input 26A voltage to the end of earth terminal, and subject to the resistance value lower than 0.3Ohm.

6 Operations Cautions 1) Whenever changing a bit, make certain the Forward / Reverse Switch is in the OFF position and tool is unplugged. 2) Do not allow chemicals such as acetone, benzene, thinner, trichloroethylene ketone, or other similar chemicals to come in contact with the screwdriver housing as damage will result. 3) Do not drop or abuse the screwdriver. 4) Do not adjust the torque setting higher than 8 on the torque scale. 5) There should be a tool rest interval when cycles three seconds or longer. This tool is intended for a duty cycle of 1.0 sec on, 3.0 sec off. 6) Do not use this screwdriver for tightening wood screws. This is Metal Assembly Screw Driver 7) Do not operate the Forward / Reverse Switch the motor is running. 8) Whenever a tool is not being used, move the Forward / Reverse Switch to the OFF position and unplug the screwdriver. 9) Don't touch For&Rew Switch during operating for keeping system from wrong judgement. CAUTION Do not drop or abuse the tool. Whenever a tool is not being used, position the Power Switch to the OFF position and unplug the power cord.

7 Description of Operation Attaching / detaching bit and bit type Push up the holder clamp by finger tip, and it will be unlocked. Thus, the bit can be freely attached and detached (single finger notion type) select such a bit whose shank is equal to the size shown below. Insert the power plug into a receptacle and set the changeover switch to F position. Apply the bit to the screw head and press the lever or push main body to, then the switch will be turned ON to start the motor running. When the screw is tighten and reach the torque that you had set, The tool will stopped automatically. To reset the tool by releasing the lever to the original position or releasing the bit From the screw head. To return the screw, set the changeover switch to R position. Servicing Maintenance and Inspection: 1. The screw driver must be operated in top condition, one day working hour must be not more than eight hours. 2. Please note don t let the motor get over heated, every minute use 10~15 screws to operate. 3. The frequency use of this electric screw driver is over than eight hours a day, still it needs periodically testing and treatment. Every 5-6 months. 4. Inspect tool cords periodically and if damaged, have them repaired by an authorized service facility. Inspect extension cords periodically and replace if damaged. 5. Do not remove any labels. Replace any damaged label.

8 CAUTION 1. The use of other than genuine KILEWS replacement parts may Result in decreased tool performance and increased maintenance, and may invalidate all warranties. 2. All repairs and maintenance of this tool and its word must be performed by an authorized service center. 3. KILEWS is not responsible for customer modification of tools for applications on which KILEWS was not consulted. 4. Repairs should by made only by authorized, trained personnel. Consult your nearest KILEWS authorized service center. 5. It is the responsibility of the employer to place the information in this manual into the hands of the operator. DO NOT ATTEMPT TO REPAIR THIS ELECTRIC SCREW DRIVER CAUTION SAVE THESE INSTRUCTIONS DO NOT DESTROY

9 Specifications MODEL Input voltage(dc) TB50L TB75L TB100L RB50L TB150L RB50P DC 40V RB75L RB75P RB100L RB100P RB150L RB150P Power Consumption Torque Repeatable Torque Accuracy (%) Torque Adjustment Unloaded Rotation Speed (R.p.m) )±10% Machine screw(mm) Screw Size Dia (N.m) 2~5 3~7.5 4~10 6~15 2~5 3~7.5 4~10 6~15 (kgf.cm) 20.4~ ~ ~ ~ ~ ~ ~ ~153 (Lbf.in) 17.7~ ~ ~ ~ ~ ~ ~ ~132.6 Tapping screw(mm) ±5% 無段式 ~ ~ ~ ~ Weight (Kg) Length (mm) *169 Model of Auxiliary Arm - KP-Aux A Model of Side Handle Ass y CF85002 CF85002 Power controller SKP-40B Bit Type 1N.m=10.2Kgf.cm 1N.m=8.85Lbf.in TB150LUW TB:T-Type Power Torque(Non-Carbon-Brush)electric screwdrivers. (TB50L TB75L TB100L TB150L) RB150LW RB:In-line Type Power Torque(Non-Carbon-Brush) electric screwdrivers. (RB50L RB75L RB100L RB150L) RB-TYPE Screwdrivers need to Collaborate with Auxiliary Arm L: Trigger start U: Top-Cord W: Round-socket Drive (B:Bit in SS 6.35mm Hexagon Type)

10

11 TB50L TB75L TB100L TB150L NO PARTS NO PARTS NAME-E PARTS NAME-C Q'ty NO PARTS NO PARTS NAME-E PARTS NAME-C Q'ty 1 AA CORD ASSEMBLY 2M 電源線 2M 1 36 GG21512 GEAR SEAT FOR "TB50" 上齒盤 (TB50) 1 2 AA N CORD ASSEMBLY 電源線 1 GG21511 GEAR SEAT FOR "TB75" 上齒盤 (TB75) 1 3 CJ20012 SUSPENSION RING 起子吊環 1 GG21510 GEAR SEAT FOR "TB100" 上齒盤 (TB100) 1 4 CB93104 HOUSING-UNDERSIDE (Power source on the top) 外殼下蓋 -( 電源上輸入線 ) 1 GG21509 GEAR SEAT FOR "TB150" 上齒盤 (TB150) 1 CB93105 HOUSING-UNDERSIDE(Power source on the bottom) 外殼下蓋 ( 電源下輸入線 ) 1 37 G20109 CENTRAL GEAR FOR "TB50" 中心齒 (TB50) 1 5 CA93104 HOUSING-UPSIDE(Power source on the top) 外殼上蓋 ( 電源上輸入線 ) 1 G20108 CENTRAL GEAR FOR "TB75" 中心齒 (TB75) 1 CA93105 HOUSING-UPSIDE(Power source on the bottom) 外殼上蓋 ( 電源下輸入線 ) 1 G20107 CENTRAL GEAR FOR "TB100" 中心齒 (TB100) 1 6 CC15002 TRIGGER ASSEMBLY 手按開關半成品 1 G20111 CENTRAL GEAR FOR "TB150" 中心齒上層 (TB150) 1 7 CE30121 PUSH ROD 推桿半成品 1 38 GH92236 IDLE GEAR FOR "TB150" 中游星齒輪 (TB150) 4 8 CE30151 FUXURE 固定片 1 39 GG21513 GEAR SEAT FOR "TB150" 中齒盤 (TB150) 1 9 H10201 SHUT OFF SWITCH 剎車開關 1 40 G20110 CENTRAL GEAR FOR "TB150" 中心齒下層 (TB150) 1 10 CH WASHER 華司 2 41 GH IDLE GEAR FOR "TB50" 游星齒輪 (TB50) 3 11 CH SCREW 螺絲 2 GH IDLE GEAR FOR "TB75" 游星齒輪 (TB75) 4 12 C40127 STICK-F/R SWITCH 正反開關切換桿 1 GH IDLE GEAR FOR "TB100" 游星齒輪 (TB100) 3 13 H10110 CHANGEOVER SWITCH 正反開關 1 GH IDLE GEAR FOR "TB150" 游星齒輪 (TB150) 4 14 EG START SWITCH PCB 啟動開關機板 1 42 GG GEAR SEAT FOR "TB50" 下齒盤 (TB50) 1 15 CH30201 SCREW FOR START SWITCH 啟動開關螺絲 2 GG GEAR SEAT FOR "TB75" 下齒盤 (TB75) 1 16 EG PCB FOR TB 控制機板成品 1 GG GEAR SEAT FOR "TB100" 下齒盤 (TB100) 1 17 E32204 HEAT SINK 散熱片 2 GG GEAR SEAT FOR "TB150" 下齒盤 (TB150) 1 18 W50109 CLAMP 散熱片夾簧 1 43 GA GEAR CASE FOR "TB50;TB75;TB100" 上離合器筒 (TB50;TB75;TB100) 1 19 CH90149 SCREW 螺絲 2 GA GEAR CASE FOR "TB150" 上離合器筒 (TB150) 1 20 CH20102 SCREW FOR HOUSING 螺絲 7 44 GN30433 MAIN BEARING 離合器主軸承 1 21 CH90154 SCREW 螺絲 2 45 GC PLATE-CLUTCH 離合器止推片 1 22 CF85002 SIDE HANDLE ASS'Y 側手把半成品 1 46 GP30351 STELL BALLS(4mm) 鋼珠 (4mm) C15002 CLAMP-SIDE HANDLE 側手把固定環 1 47 GC CAM 上離合器頭 1 24 C15001 HANDLE-SIDE HANDLE 手把 1 48 GU30372 STOP PILOT 酒杯 1 25 CH30195 SCREW 六角螺絲 1 49 GP30381 STELL BALLS(6mm) 跳脫鋼珠 (6mm) 3 26 MI PILOT ROD 開關引導棒 1 50 GP30382 CUSHION 鋼珠墊塊 5.5* 5.9mm 3 27 MO91503 MOTOR ASSEMBLY-TB50/75/100 馬達整組 (TB50/75/100) 51 GP30381 STELL BALLS(6mm) 酒杯鋼珠 (6mm) 2 MO91502 MOTOR ASSEMBLY-TB150 馬達整組 (TB150) 1 52 GD91405 SHAFT FOR HEX 6.35mm 傳動軸 B 頭用 1 28 CH SCREW FOR MOTOR 馬達固定螺絲 4 GD SHAFT FOR Round-socket 傳動軸 W 頭用 1 29 M11321 GEAR FOR "TB50" 主齒 (TB50) 1 53 GP30371 STELL BALLS(3.15mm) HEX 起子頭帽鋼珠 (3.15mm) B 頭用 2 M11320 GEAR FOR "TB75" 主齒 (TB75) 1 54 GF90323 WARING PLATE 扭力推盤 1 M11319 GEAR FOR "TB100" 主齒 (TB100) 1 55 GE92383 WARING SPRING FOR "TB50" 扭力彈簧 (TB50) 1 M11318 GEAR FOR "TB150" 主齒 (TB150) 1 GE92384 WARING SPRING FOR "TB75" 扭力彈簧 (TB75) 1 30 MG PILOT ROD 陶瓷棒 1 GE92385 WARING SPRING FOR "TB100" 扭力彈簧 (TB100) 1 31 GZ CLUTCH ASSEMBLY FOR "TB50B" 離合器整組 (TB50B) 1 GE92386 WARING SPRING FOR "TB150" 扭力彈簧 (TB150) 1 GZ CLUTCH ASSEMBLY FOR "TB50W" 離合器整組 (TB50W) 1 56 GY21322 WARING SPRING BASE 止推盤 1 GZ CLUTCH ASSEMBLY FOR "TB75B" 離合器整組 (TB75B) 1 57 GN30432 BEARING 軸承 1 GZ CLUTCH ASSEMBLY FOR "TB75W" 離合器整組 (TB75W) 1 58 G20205 CLUTCH CASE 下離合器筒 1 GZ CLUTCH ASSEMBLY FOR "TB100B" 離合器整組 (TB100B) 1 59 GL TORQUE ADJUSTING PINS 扭力調整棒 4 GZ CLUTCH ASSEMBLY FOR "TB100W" 離合器整組 (TB100W) 1 60 GM30493 TORQUE ADJUSTING RING 扭力調整環 1 GZ CLUTCH ASSEMBLY FOR "TB150B" 離合器整組 (TB150B) 1 61 GS30503 "C"RING 扭力環固定環 1 GZ CLUTCH ASSEMBLY FOR "TB150W" 離合器整組 (TB150W) 1 62 G21303 SPACER FOR HEX 6.35mm 起子頭帽墊圈 LB 專用 1 32 MI PILOT ROD 開關引導棒 1 63 GO21342 BIT SPRING FOR HEX 6.35mm 起子頭帽彈簧 LB 專用 2 33 GK20232 "C"RING 齒輪固定 C 環 1 64 GJ30471B BIT SLEEVE FOR HEX 6.35mm 起子頭帽 LB 專用 1 34 GI28442 IRON WASHER 齒輪固定片 1 65 GQ30472 "C"RING FOR HEX 6.35mm 起子頭帽 C 環 LB 專用 1 35 GH92235 IDLE GEAR FOR "TB50" 游星齒輪 (TB50) 3 66 CD91032 COUPLER 前鎖環 1 GH92234 IDLE GEAR FOR "TB75" 游星齒輪 (TB75) 4 67 CH GROUNDING MEANS 接地線 1 GH92233 IDLE GEAR FOR "TB100" 游星齒輪 (TB100) 3 68 CH SCREW 接地線螺絲 1 GH92232 IDLE GEAR FOR "TB150" 游星齒輪 (TB150) 4 69 CK TRIGGER SPRING 壓板彈簧 1 70 E CERAMICS CAPACITOR 陶瓷電容 104/SEM 1

12

13 RB50L RB75L RB100L RB150L NO PARTS NO PARTS NAME-E PARTS NAME-C Q'ty NO PARTS NO PARTS NAME-E PARTS NAME-C Q'ty 1 AA CORD ASSEMBLY 2M 電源線 2M 1 GH92232 IDLE GEAR FOR "RB150L" 上游星齒輪 (RB150L) 4 2 AA N CORD ASSEMBLY 電源線 1 35 GG21512 GEAR SEAT FOR "RB50L" 上齒盤 (RB50L) 1 3 CJ20012 SUSPENSION RING 起子吊環 1 GG21511 GEAR SEAT FOR "RB75L" 上齒盤 (RB75L) 1 4 CC50016 TRIGGER ASSEMBLY 手按開關半成品 1 GG21510 GEAR SEAT FOR "RB100L" 上齒盤 (RB100L) 1 CC TRIGGER ASSEMBLY -ESD 手按開關半成品 -ESD 1 GG21509 GEAR SEAT FOR "RB150L" 上齒盤 (RB150L) 1 5 C40747F HOUSING-UNDERSIDE A'ssy 外殼下蓋半成品 1 36 G20109 CENTRAL GEAR FOR "RB50L" 中心齒 (RB50L) 1 C F HOUSING-UNDERSIDE A'ssy-ESD 外殼下蓋半成品 -ESD 1 G20108 CENTRAL GEAR FOR "RB75L" 中心齒 (RB75L) 1 6 CA93106 HOUSING-UPSIDE 外殼上蓋 1 G20107 CENTRAL GEAR FOR "RB100L" 中心齒 (RB100L) 1 CA HOUSING-UPSIDE-ESD 外殼上蓋 -ESD 1 G20111 CENTRAL GEAR FOR "RB150L" 中心齒上層 (RB150L) 1 7 CE PUSH ROD 開關推桿半成品 1 37 GH92236 IDLE GEAR FOR "RB150" 中游星齒輪 (RB150L) 4 8 CE80001 FUXURE 固定片 1 38 GG21513 GEAR SEAT FOR "RB150" 中齒盤 (RB150L) 1 9 CH30200 SCREW FOR FUXURE 固定片螺絲 2 39 G20110 CENTRAL GEAR FOR "RB150" 中心齒下層 (RB150L) 1 10 EG START SWITCH PCB 啟動開關機板 1 40 GH IDLE GEAR FOR "RB50L" 下游星齒輪 (RB50L) 3 11 CH30201 SCREW FOR START PCB 螺絲 2 GH IDLE GEAR FOR "RB75L" 下游星齒輪 (RB75L) 4 12 E33105 LED LED 1 GH IDLE GEAR FOR "RB100L" 下游星齒輪 (RB100L) 3 13 EG CHANGEOVER SWITCH PCB 正反開關機板 1 GH IDLE GEAR FOR "RB150L" 下游星齒輪 (RB150L) 4 14 CI F/R SWITCHING ELEMENT-RB50L 正反轉推板 -RB50L 1 41 GG GEAR SEAT FOR "RB50L" 下齒盤 (RB50L) 1 CI50212 F/R SWITCHING ELEMENT-RB75L 正反轉推板 -RB75L 1 GG GEAR SEAT FOR "RB75L" 下齒盤 (RB75L) 1 CI F/R SWITCHING ELEMENT-RB100L 正反轉推板 -RB100L 1 GG GEAR SEAT FOR "RB100L" 下齒盤 (RB100L) 1 CI F/R SWITCHING ELEMENT-RB150L 正反轉推板 -RB150L 1 GG GEAR SEAT FOR "RB150L" 下齒盤 (RB150L) 1 15 EG PCB FOR RB 控制機板成品 1 42 GA91286 GEAR CASE FOR "RB50L,75L,100L" 上離合器筒 (RB50L,75L,100L) 1 16 E32204 HEAT SINK 散熱片 2 GA91285 GEAR CASE FOR "RB150L" 上離合器筒 (RB150L) 1 17 W50109 CLAMP 散熱片夾簧 1 43 GN30433 MAIN BEARING 離合器主軸承 1 18 CH90154 SCREW FOR PCB 固定 PCB 螺絲 2 44 GC PLATE-CLUTCH 離合器止推片 1 CH20510 SCREW FOR PCB-ESD 固定 PCB 螺絲 -ESD 2 45 GP30351 STELL BALLS(4mm) 鋼珠 (4mm) P INSULATING WASHER FOR ESD ONLY 絕緣墊片 (ESD) 4 46 GC CAM 上離合器頭 1 20 CH20102 SCREW FOR HOUSING 螺絲 4 47 GU30372 STOP PILOT 酒杯 1 21 CF85002 SIDE HANDLE ASS'Y 側手把半成品 1 48 GP30381 STELL BALLS(6mm) 跳脫鋼珠 (6mm) 3 22 C15002 CLAMP-SIDE HANDLE 側手把固定環 1 49 GP30382 CUSHION 鋼珠墊塊 5.5* 5.9mm 3 23 C15001 HANDLE-SIDE HANDLE 手把 1 50 GP30381 STELL BALLS(6mm) 酒杯鋼珠 (6mm) 2 24 CH30195 SCREW 六角螺絲 1 51 GD91405 SHAFT FOR HEX 5.0mm 傳動軸 B 頭用 1 25 MI PILOT ROD 開關引導棒 1 GD SHAFT FOR Round-socket 傳動軸 W 頭用 1 26 MO91505 MOTOR ASSEMBLY-RB50L,75L,100L 馬達整組 -RB50L,75L,100L 1 52 GP30371 STELL BALLS(3.15mm) HEX 起子頭帽鋼珠 (3.15mm) B 頭用 2 MO91504 MOTOR ASSEMBLY-RB150L 馬達整組 -RB150L 1 53 GF90323 WARING PLATE 扭力推盤 1 27 CH SCREW FOR MOTOR 馬達固定螺絲 4 54 GE92383 WARING SPRING FOR "RB50L" 扭力彈簧 (RB50L) 1 28 M11321 GEAR FOR "RB50L" 主齒 (RB50L) 1 GE92384 WARING SPRING FOR "RB75L" 扭力彈簧 (RB75L) 1 M11320 GEAR FOR "RB75L" 主齒 (RB75L) 1 GE92385 WARING SPRING FOR "RB100L" 扭力彈簧 (RB100L) 1 M11319 GEAR FOR "RB100L" 主齒 (RB100L) 1 GE92386 WARING SPRING FOR "RB150L" 扭力彈簧 (RB150L) 1 M11318 GEAR FOR "RB150L" 主齒 (RB150L) 1 55 GY21322 WARING SPRING BASE 止推盤 1 29 MG PILOT ROD 陶瓷棒 1 56 GN30432 BEARING 軸承 1 30 GZ15005R CLUTCH ASSEMBLY FOR "RB50LB" 離合器整組 (RB50LB) 1 57 G20205 CLUTCH CASE 下離合器筒 1 GZ15005R-1 CLUTCH ASSEMBLY FOR "RB50LW" 離合器整組 (RB50LW) 1 58 GL TORQUE ADJUSTING PINS 扭力調整棒 4 GZ15007R CLUTCH ASSEMBLY FOR "RB75LB" 離合器整組 (RB75LB) 1 59 GM30493 TORQUE ADJUSTING RING 扭力調整環 1 GZ15007R-1 CLUTCH ASSEMBLY FOR "RB75LW" 離合器整組 (RB75LW) 1 60 GS30503 "C"RING 扭力環固定環 1 GZ15010R CLUTCH ASSEMBLY FOR "RB100LB" 離合器整組 (RB100LB) 1 61 G21303 SPACER FOR HEX 起子頭帽墊圈 LB 專用 1 GZ15010R-1 CLUTCH ASSEMBLY FOR "RB100LW" 離合器整組 (RB100LW) 1 62 GO21342 BIT SPRING FOR HEX 起子頭帽彈簧 LB 專用 2 GZ15015R CLUTCH ASSEMBLY FOR "RB150LB" 離合器整組 (RB150LB) 1 63 GJ30471B BIT SLEEVE FOR HEX 起子頭帽 LB 專用 1 GZ15015R-1 CLUTCH ASSEMBLY FOR "RB150LW" 離合器整組 (RB150LW) 1 64 GQ30472 "C"RING FOR HEX 起子頭帽 C 環 LB 專用 1 31 MI PILOT ROD 開關引導棒 1 65 CD91034 COUPLER 前鎖環 1 32 GK20232 "C"RING 齒輪固定 C 環 1 CD COUPLER-ESD 前鎖環 -ESD 1 33 GI28442 IRON WASHER 齒輪固定片 1 66 CH GROUNDING MEANS 接地線 1 34 GH92235 IDLE GEAR FOR "RB50L" 上游星齒輪 (RB50L) 3 67 CH SCREW 地線螺絲 1 GH92234 IDLE GEAR FOR "RB75L" 上游星齒輪 (RB75L) 4 68 CH90149 SCREW 螺絲 2 GH92233 IDLE GEAR FOR "RB100L" 上游星齒輪 (RB100L) 3 69 CK TRIGGER SPRING 壓板彈簧 1

14

15 RB50P RB75P RB100P RB150P NO PARTS NO PARTS NAME-E PARTS NAME-C Q'ty NO PARTS NO PARTS NAME-E PARTS NAME-C Q'ty 1 AA CORD ASSEMBLY 2M 電源線 2M 1 GG21511 GEAR SEAT FOR RB75P 上齒盤 (RB75P) 1 2 AA N CORD ASSEMBLY 電源線 1 GG21510 GEAR SEAT FOR RB100P 上齒盤 (RB100P) 1 3 CJ20012 SUSPENSION RING 起子吊環 1 GG21509 GEAR SEAT FOR RB150P 上齒盤 (RB150P) 1 4 C40748F HOUSING-UNDERSIDE (A'ssy For Sale) 下蓋 1 35 G20109 CENTRAL GEAR FOR RB50P 中心齒 (RB50P) 1 C F HOUSING-UNDERSIDE (ESD) (A'ssy For Sale) 下蓋 - 防靜電 1 G20108 CENTRAL GEAR FOR RB75P 中心齒 (RB75P) 1 5 CA93107 HOUSING-UPSIDE 上蓋 1 G20107 CENTRAL GEAR FOR RB100P 中心齒 (RB100P) 1 CA HOUSING-UPSIDE (ESD) 上蓋 - 防靜電 1 G20111 CENTRAL GEAR FOR RB150P 中心齒上層 (RB150P) 1 6 CE PUSH ROD 開關推桿半成品 1 36 GH92236 IDLE GEAR FOR RB150P 中游星齒輪 (RB150P) 4 7 CE80001 FIXTURE 三合一固定片 1 37 GG21513 GEAR SEAT FOR RB150P 中齒盤 (RB150P) 1 8 CH30200 SCREW FOR FIXTURE 三合一固定片螺絲 2 38 G20110 CENTRAL GEAR FOR RB150P 中心齒下層 (RB150P) 1 9 E33105 LED LED 1 39 GH IDLE GEAR FOR RB50P 下游星齒輪 (RB50P) 3 10 EG CHANGEOVER SWITCH PCB 正反開關機板 1 GH IDLE GEAR FOR RB75P 下游星齒輪 (RB75P) 4 11 CI F/R SWITCHING ELEMENT-RB50L 正反轉推板 -RB50L 1 GH IDLE GEAR FOR RB100P 下游星齒輪 (RB100P) 3 CI50212 F/R SWITCHING ELEMENT-RB75L 正反轉推板 -RB75L 1 GH IDLE GEAR FOR RB150P 下游星齒輪 (RB150P) 4 CI F/R SWITCHING ELEMENT-RB100L 正反轉推板 -RB100L 1 40 GG GEAR SEAT FOR RB50P 下齒盤 ( RB50P) 1 CI F/R SWITCHING ELEMENT-RB150L 正反轉推板 -RB150L 1 GG GEAR SEAT FOR RB75P 下齒盤 (RB75P) 2 12 H10201 SHUT OFF SWITCH 剎車開關 1 GG GEAR SEAT FOR RB100P 下齒盤 (RB100P) 3 13 CH SCREW FOR SHUT OFF SWITCH 剎車開關螺絲 2 GG GEAR SEAT FOR RB150P 下齒盤 (RB150P) 4 14 EG PCB 機板成品 1 41 GA91286 GEAR CASE FOR RB50/75/100P 上離合器筒 (RB50/75/100P) 1 15 E32204 HEAT SINK 散熱片 2 GA91285 GEAR CASE FOR RB150P 上離合器筒 (RB150P) 1 16 W50109 CLAMP 散熱片夾簧 1 42 GN30433 MAIN BEARING 離合器主軸承 1 17 CH90154 SCREW FOR PCB 固定 PCB 螺絲 2 43 GC PLATE-CLUTCH 離合器止推片 1 CH20510 SCREW FOR PCB-ESD 固定 PCB 螺絲 -ESD 2 44 GP30351 STELL BALLS(4ψ) 鋼珠 (4ψ) P INSULATING WASHER FOR ESD ONLY 絕緣墊片 (ESD) 4 45 GX90306 CAM 上離合器頭 1 19 CH20102 SCREW FOR HOUSING 外殼螺絲 4 46 GP30381 STELL BALLS 6ψ 跳脫鋼珠 6ψ 3 20 CF85002 SIDE HANDLE ASS'Y 側手把半成品 1 47 GP30383 CUSHION 鋼珠墊塊 4.7* 5.9mm 3 21 C15002 CLAMP-SIDE HANDLE 側手把固定環 1 48 GF90325 WARING PLATE 扭力推盤 1 22 C15001 HANDLE-SIDE HANDLE 手把 1 49 GV90330 SPRING CAP 扭力推盤蓋 1 23 CH30195 SCREW 六角螺絲 1 50 GO90342 INNER SPRING 下壓式彈簧 1 24 MI PILOT ROD 開關引導棒 1 51 GU30372 STOP PILOT 停止用酒杯 1 25 CH SCREW FOR MOTOR 馬達螺絲 4 52 GE92390 WARING SPRING FOR "RB50P" 扭力彈簧 RB50P 1 26 MO91505CE MOTOR ASSEMBLY FOR RB50/75/100P 馬達整組 (RB50/75/100P) 1 GE92391 WARING SPRING FOR "RB75P" 扭力彈簧 RB75P 1 MO91504CE MOTOR ASSEMBLY FOR RB150P 馬達整組 (RB150P) 1 GE92392 WARING SPRING FOR "RB100P" 扭力彈簧 RB100P 1 27 M11321 GEAR FOR RB50P 馬達主齒 RB50P 1 GE92393 WARING SPRING FOR "RB150P" 扭力彈簧 RB150P 1 M11320 GEAR FOR RB75P 馬達主齒 RB75P 1 53 GP30381 STELL BALLS 6ψ 酒杯鋼珠 6ψ 2 M11319 GEAR FOR RB100P 馬達主齒 RB100P 1 54 GD91406 SHAFT FOR "PB" TYPE 傳動軸 B-TYPE 1 M11318 GEAR FOR RB150P 馬達主齒 RB150P 1 GD91407 SHAFT FOR "PW" TYPE 傳動軸 W-TYPE 1 28 MG PILOT ROD 陶瓷棒 1 55 GP30371 STELL BALLS 3.15ψ 起子頭帽鋼珠 PB 3.15ψ 2 29 GZ B CLUTCH ASSEMBLY FOR "RB50PB" 離合器成品,RB50PB 1 56 GY21323 WARING SPRING BASE 止推盤 1 GZ W CLUTCH ASSEMBLY FOR "RB50PW" 離合器成品,RB50PW 1 57 GB30445 CLUTCH CASE A'SSY 下離合器筒半成品 1 GZ B CLUTCH ASSEMBLY FOR "RB75PB" 離合器成品,RB75PB 1 58 GL30484 TORQUE ADJUSTING PINS 扭力調整棒 4 GZ W CLUTCH ASSEMBLY FOR "RB75PW" 離合器成品,RB75PW 1 59 GM30493 TORQUE ADJUSTING RING 扭力調整環 1 GZ B CLUTCH ASSEMBLY FOR "RB100PB" 離合器成品,RB100PB 1 60 GS30503 "C"RING 扭力環固定環 1 GZ W CLUTCH ASSEMBLY FOR "RB100PW" 離合器成品,RB100PW 1 61 G21303 SPACER FOR HEX 起子頭帽墊圈 PB 專用 1 GZ B CLUTCH ASSEMBLY FOR "RB150PB" 離合器成品,RB150PB 1 62 GO21342 BIT SPRING FOR HEX 起子頭帽彈簧 PB 專用 1 GZ W CLUTCH ASSEMBLY FOR "RB150PW" 離合器成品,RB150PW 1 63 GJ21350 BIT SLEEVE FOR HEX 起子頭帽 PB 專用 1 30 MI PILOT ROD 開關引導棒 1 64 GQ21362 "C"RING FOR HEX 起子頭帽 C 環 PB 專用 1 31 GK20232 "C" RING 齒輪固定 C 環 1 65 CD91034 COUPLER 前鎖環 1 32 GI28442 IRON WASHER 齒輪固定片 1 CD COUPLER-ESD 前鎖環 -ESD 1 33 GH92235 IDLE GEAR FOR RB50P 上游星齒輪 (RB50P) 3 66 CH GROUNDING MEANS 接地線 1 GH92234 IDLE GEAR FOR RB75P 上游星齒輪 (RB75P) 4 67 CH SCREW 接地線螺絲 1 GH92233 IDLE GEAR FOR RB100P 上游星齒輪 (RB100P) 3 68 CH90149 SCREW 螺絲 2 GH92232 IDLE GEAR FOR RB150P 上游星齒輪 (RB150P) 4 69 E CERAMICS CAPACITOR 陶瓷電容 104/SEM 1 34 GG21512 GEAR SEAT FOR RB50P 上齒盤 (RB50P) 1 70 E30703 DIODE 二極體 1N4148 1

16 Accessories 1 BIT Type: No Bit use in dia 1.3~1.8mm screw No Bit use in dia 1.6~2.0mm screw No Bit use in dia 2.0~2.6mm screw No Bit use in dia 3.0~4.0mm screw TB50LB(W);RB50LB(W);RB50PB(W) with BIT(socket) 3# 2 Pcs (1Pcs) TB75LB(W);RB75LB(W);RB75PB(W) withbit(socket) 3# 2 Pcs (1 Pcs) TB100LB(W);RB100LB(W);RB100PB(W) withbit(socket) 3# 2 Pcs (1 Pcs) TB150LB(W);TB150LB(W);RB150PB(W) withbit(socket) 3# 2 Pcs (1 Pcs) 2 Suspension rack and Torque fixing ring acceptable for use with the tool are available from KILEWS catalogue. Torque Adjustment Operation To adjust the torque on these screwdrivers. Proceed as follows : 1. Determine the torque output of the tool by checking a tightened Fastener with a torque wrench. 2. Increase or decrease the torque by rotating the Spring Adjusting Ring. Rotating the Ring clockwise to a higher number on the torque Scale increase torque output while rotating the Ring counterclockwise to a lower number decreases the torque output. 3. Check the adjustment with a torque wrench. A number of factors will affect torque output from one job to another. Final torque adjustment should be made at the job through a of series of gradual increase. Always start below the desired torque and work upward. 4. Adjust the bit torque by changing the driving in length of the adjust ring at the end. 5. The relationship between torque scale and bit torque is as shown Ring, in the torque diagram. The figures of torque scale do not indicate bit torque values. However, the clamping torque of screw itself is different form type, size, material of the screw and the material of its mating part. Use it as standard to obtain an appropriate clamping torque. 6. The (Return torque method) in which once-clamped screw is returned with torque wrench or the like is available as one of torque control methods however, note that the measured values by the return torque method generally appear in 10%~30% lower than the actually clamping torque. 7. The torque checker measures the torque of screwdriver. The clamping torque of screw itself is different from the clamped conditions. Understand the correlation between clamping torque values and the torque checker values perform the torque control properly. CAUTION 1. Also in reverse rotation, the clutch is turned off in such manner as in normal rotation, stopping the motor running. Accordingly, when the screw tightened at a large torque, set it to a higher torque scale. 2. The number from zero to eight on the Torque Scale are reference number only and not an indication of actual torque output.