电动剃须刀

Size: px

Start display at page:

Download "电动剃须刀"

花解
5 years ago
Views:

1 使用说明书 ( 另附保修证 ) Operating Instructions ( 家用 ) 电动剃须刀 (Household) AC/Rechargeable Shaver 型号 Model No. ES GA20 中文 2 English 9 在使用本产品前, 请仔细阅读本说明书并妥善保管, 以备将来参考 Before operating this unit, please read these instructions completely and save them for future use.

2 中文重要事项电源线分离, 以防触电请在装有两个内刀头的状态下进行清洗, 若使用剃须刀在仅装有一个内刀头的状态下进行清洗, 可注意 - 因外刀网很薄, 若使用不当就可能能会损坏剃须刀可用清水清洗剃须刀, 不造成损坏使用剃须刀前, 请确认外刀网是否损坏如果外刀网已损坏, 请不要使用该剃须刀, 因为这样会割伤皮肤请勿用于修剪宠物的毛发充电请不要使用除 RE7-51 充电器以外的任何电源线或充电器进行充电将充电器插入家用电源插座内进行充电, 操作时双手应保持干燥剃须刀在使用和充电过程中可能会变热, 但这不是故障不要将剃须刀放置在阳光直射或有其他热源的地方进行充电从家用电源插座上拔出充电器时, 不要用力拉电源线, 因为可能会损坏电源线, 应抓紧充电器的插头部位电源线不能更换, 如果电源线损坏, 此充电器应废弃充电的最佳环境温度为 15 至 35 摄氏度要使用盐水或热水不要将剃须刀长时间浸泡在水中可用蘸肥皂水的布擦拭剃须刀不要使用稀释剂, 汽油或酒精擦拭剃须刀任何部位存放剃须刀存放剃须刀时请拔出电源线不要折弯电源线或将电源线缠绕在剃须刀上本品不宜供肢体感官或精神上有残疾者或缺乏经验和知识者 ( 包括儿童 ) 使用, 必须有监护者从旁监督并对本品的使用加以指导, 且对使用者的安全能承担责任请避免儿童将本品视为玩具, 从而引发危险请妥善处理本产品的包装袋, 避免婴幼儿窒息等意外发生请置于儿童触摸不到的地方请勿让婴幼儿接触润滑油若充电状态指示灯不亮, 请稍等直至其亮请妥善保管本说明书起清洁剃须刀警告 - 用水清洗剃须刀前, 请将剃须刀与 2

3 各部分名称 A 保护盖 B 外刀部 1 外刃架 2 外刀网 3 外刀网释放按钮 C 内刀头 D 机身 4 外刃架释放按钮 5 0/1 开关 6 锁环 7 电池电量指示灯 ( ) 8 充电状态指示灯 ( ) 9 电源线插孔 : 修剪刀 ; 修剪刀操纵杆 E 充电器 (RE7 51) 电源线电源线插头 F 旅行携带小包 G 清洁刷 H 润滑油充电充电中 1 将充电器电源线插头与剃须刀连接 2 将充电器插头插入家用电源插座里亮起, 充电开始闪烁, 充电完成 ( 约 1 小时, 即可完成充电 ) 购买后初次使用或半年以上未使用过, 充电指示灯可能不会立即亮, 继续充电几分钟后即正常使用锁环使用锁环上锁或开启 0/1 开关 1. 旋转锁环直至发出咔嗒的响声到位开启 0/1 开关 : 用于剃须清洗剃须刀或润滑剃须刀时锁住 0/1 开关 : 用于随身携带剃须刀时中文

4 中文利用交流电剃须当电池电量低时, 您可将剃须刀通过充电器连接至家用电源插座, 利用交流电进行剃须如果剃须刀不能正常使用, 请充电约 1 分钟后再使用关于指示灯充电时充电完成后充电完成 10 分钟后使用修剪刀将修剪刀操纵杆往上推, 以打开修剪刀将修剪刀放置与皮肤成直角 (90 度 ) 的位置, 然后从上向下移动进行修剪剃须使用剃须刀红灯亮红灯闪烁, 每秒一次红灯闪烁, 每 2 秒一次电池电量不足时在闪烁后还可剃须 1 至 2 次 ( 根据使用情况而定 ) 闪烁充足电后大约可提供 14 次剃须所需的电量 ( 一次剃须约为 3 分钟 ) 1 旋转锁环并按下 0/1 开关第 3 页 90 2 如上图所示握住剃须刀剃须轻轻地压向面部开始剃须用另一只手绷紧脸上皮肤, 逆着胡须生长方向前后移动剃须刀当皮肤适应剃须刀之后您可以稍稍加大压力, 但施加压力过大就可能会造成皮肤伤害

5 清洁清洁 1. 将剃须刀上的充电器电源线插头拔出 2. 在外刀网上涂抹少量洗手液和水 3. 旋转锁环, 开启 0/1 开关 4. 按下 0/1 开关 2 秒钟以上以启动声波洗净模式与指示灯交替闪烁约 20 秒钟后, 电源自动关闭, 或者按 0/1 开关关闭电源 5. 取下外刀部, 按下 0/1 开关 2 秒钟以上, 启动声波洗净模式使用流动水进行清洁 6. 用干布拭去水珠 7. 使外刀部和剃须刀彻底干燥 8. 将外刀部安装至剃须刀 9. 给剃须刀上润滑油左侧符号表示适合用在打开的水龙头下进行清洗警告 : 用水清洗剃须刀前, 请将剃须刀与电源线分离, 以防触电使用声波洗净模式的注意事项在声波洗净模式下剃须可能会损伤皮肤请先关闭剃须刀电源, 重新打开即可取消声波洗净模式使用剃须刀时不要将手指放在 0/1 开关上这样会导致剃须刀关闭或进入声波洗净模式中文

6 中文润滑为长期保持剃须的舒适度, 建议使用附赠的润滑油 1. 关闭剃须刀电源 2. 给每个外刀网滴一滴润滑油 3. 推起修剪刀并滴一滴润滑油 4. 开启剃须刀电源, 运转约 5 秒钟 5. 关闭剃须刀电源, 使用软布将外刀网上多余的润滑油拭去更换外刀网和内刀头为了维持剃须刀的剃须性能, 建议外刀网每年更换一次, 内刀头每两年更换一次更换外刀网 1. 如图所示, 按下外刃架释放按钮并向上提起, 取出外刀部 2 3 更换内刀头如图所示, 按下外刀网释放按钮, 拉出外刀网 3. 向内插入外刀网, 直至卡到位请注意外刀网的安装方向安装到剃须刀时, 请确保外刀网插入到外刃架内 1. 如图所示, 按下外刃架释放按钮并向上提起, 取出外刀部 2. 如图所示, 取下内刀头, 一次取一个不要触摸内刀头的边沿 ( 金属部分 ), 以防止您的手受伤 3. 如图所示, 安装内刀头时, 每次插入一只内刀头, 直至其咔嗒入位

7 (A) 使用刷子清洁 (B) 1. 使用短刷, 沿左图所示 (A) 的移动方向移动, 清洁内刀头使用长刷, 清洁外刀网剃须刀机身和修剪刀请勿沿 (B) 方向移动短刷, 因为这样将损坏内刀头而影响刀片的锋利度请勿使用短刷清洁外刀网内置式充电电池的取出方式剃须刀内藏有可充电的电池, 在消费者决定废弃剃须刀前, 请务必将电池从剃须刀中取出分解剃须刀, 取出电池前, 一定要断开电源鼓励消费者在决定废弃剃须刀前, 事先征求经销商或本公司指定维修点的意见, 尽量延长剃须刀的使用寿命当消费者决定废弃剃须刀又不想自行分解剃须刀取出电池时, 鼓励消费者将器具送往本公司指定的维修站, 由维修店对电池进行分解和回收电池务必废弃于政府规定的地方或回收处理单位按下图所示的 1 ~ 5 的顺序拆开本体, 卸下电池中文

8 中文环境保护与资源回收此剃须刀使用锂电池如果贵国有相关规定, 请务必在指定处对旧电池进行统一处理规格产品名称电动剃须刀产品型号 ES-GA20 充电器额定输入 V 50-60Hz 180mA 充电器额定输出 5.4V 1.2A 马达电压 3.6V 充电时间约 1 小时原产地本机 : 日本充电器 : 中国生产日期请见商品上刻印执行标准中国国家 GB 附录 B 标准 GB 本产品仅适合家庭使用

9 Important Using the shaver Caution - The outer foil is very thin and can be damaged if not used correctly. Check that the foil is not damaged before using the shaver. Do not use the shaver if the foil etc. is damaged as you will cut your skin. Charging the shaver Do not use any power cord or AC adaptor other than this adaptor (RE7 51). Plug in the adaptor into a household outlet where there is no moisture and handle it with dry hands. The shaver may become warm during use and charging. However, this is not a malfunction. Do not charge the shaver where it will be exposed to direct sunlight or other heat sources. Hold the adaptor when disconnecting it from the household outlet. If you tug on the power cord, you may damage it. The supply cord cannot be replaced. If the cord is damaged, the appliance should be scrapped. Adequate ambient temperature for charging is C. If the charge status lamp does not glow initially when the shaver is plugged in, wait for a short while until it does. Cleaning the shaver Warning - Disconnect the power cord from the shaver before cleaning it in water to prevent electric shock. Keep both the inner blades inserted. If only one of the inner blades is inserted, the shaver may be damaged. If you clean the shaver with water, do not use salt water or hot water. Do not soak the shaver in water for a long period of time. Wipe it with a cloth dampened with soapy water. Do not use thinner, benzine or alcohol. Storing the shaver Disconnect the power cord when storing the shaver. Do not bend the power cord or wrap it around the shaver. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Please properly store or dispose the plastic bag of the appliance to avoid any accidents, such as infants suffocation, etc. Keep the plastic bag away from infants. Keep the oil away from children. Keep these operating instructions in a safe place. English

10 English 10 Parts identification A Protective cap B Outer foil section 1 Foil frame 2 System outer foil 3 System outer foil release buttons C Inner blades D Main body 4 Foil frame release buttons 5 0/1 switch 6 Lock ring 7 Battery capacity lamp ( ) 8 Charge status lamp ( ) 9 Appliance socket : Trimmer ; Trimmer handle E Adaptor (RE7 51) Power cord Appliance plug F Travel pouch G Cleaning brush H Oil 1 2 Charge Charging Insert the appliance plug into the shaver. Plug in the adaptor into a household outlet. glows and charging starts. Charging is completed when blinks. (after approx. 1 hour) When charging the shaver for the first time or when it has not been in use for more than 6 months, the charge status lamp may not glow. It will eventually glow if kept connected. Using the lock ring Use the lock ring to lock or unlock the 0/1 switch. 1. Rotate the lock ring until it clicks. Unlock the 0/1 switch: For when shaving, washing the shaver, lubricating the shaver. Lock the 0/1 switch: For when carrying the shaver.

11 Cord shaving If you insert the appliance plug to the shaver and plug in the adaptor into a household outlet, you can use it even if the battery capacity is low. If the shaver does not work, continue charging it for approx. 1 minute. About the lamp While charging After charging is completed 10 minutes after charging is completed Using the trimmer Slide the trimmer handle up. Place at a right angle to your skin and move downwards to trim your sideburns. Shave Using the shaver 90 Glows red. Blinks red once every second. When the battery capacity is low Blinks red once every 2 seconds. You can shave 1 to 2 times after blinks. (This will differ depending on usage.) blinks. A full charge will supply enough power for approx. 14 shaves of 3 minutes each. 1 Rotate the lock ring and press the 0/1 switch. Page 10 2 Hold the shaver as illustrated above and shave. Start out shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave. 11 English

12 English Clean Cleaning 1. Disconnect the power cord from the shaver. 2. Apply some hand soap and some water to the outer foil. 3. Rotate the lock ring to unlock the 0/1 switch. 4. Press the 0/1 switch for more than 2 seconds to activate the sonic vibration cleaning mode. or flash around randomly. After about 20 seconds, it will be automatically turned off, or you can turn it off by pressing the 0/1 switch. 5. Remove the outer foil section and press the 0/1 switch for more than 2 seconds to activate the sonic vibration cleaning mode and clean it with running water. The mark on the left means suitable for cleaning under an open water tap. 6. Wipe off any drops of water with a dry cloth. 7. Dry the outer foil section and the shaver completely. 8. Attach the outer foil section to the shaver. 9. Lubricate the shaver. Warning - Disconnect the power cord from the shaver before cleaning it in water to prevent electric shock. Caution for the sonic vibration cleaning mode Shaving in the sonic vibration cleaning mode may damage your skin. Turn the shaver off and then on again to cancel the sonic vibration cleaning mode. Do not place your fingers on the 0/1 switch while using the shaver. This may cause the shaver to turn off or enter the sonic vibration cleaning mode. 12

13 Lubrication To maintain shaving comfort for a long time, it is recommended that the oil provided with the shaver is used. 1. Switch off the shaver. 2. Apply one drop of oil to each of the outer foils. 3. Raise the trimmer and apply a drop of oil. 4. Switch the shaver on, and run it for approximately five seconds. 5. Switch off the shaver, and wipe off any excess oil from the outer foils with a soft cloth. Replacing the system outer foil and the inner blades system outer foil once every year inner blade once every two years Replacing the system outer foil 1. Press the foil frame release buttons and lift the outer foil section upwards as illustrated Press the system outer foil release buttons and pull down the system outer foil as illustrated. 3. Insert the system outer foil until it clicks. Always attach the system outer foil in proper direction. Always insert the system outer foil to the foil frame when attaching to the shaver. Replacing the inner blades 1. Press the foil frame release buttons and lift the outer foil section upwards as illustrated. 2. Remove the inner blades one at a time as illustrated. 2 3 Do not touch the edges (metal parts) of the inner blades to prevent injury to your hand. 3. Insert the inner blades one at a time until they click as illustrated. English 13

14 Cleaning with the brush 1. Clean the inner blades using the short brush by moving it in direction (A). Clean the system outer foil, the shaver body and (A) (B) the trimmer using the long brush. Do not move the short brush in direction (B) as it will damage the inner blades and affect their sharpness. Do not use the short brush to clean the outer foils. Removing the built-in rechargeable battery Remove the built-in rechargeable battery before disposing of the shaver. Please make sure that the battery is disposed of at an officially designated location if there is one. Do not dismantle or replace the battery so that you can use the shaver again. This could cause fire or an electric shock. Replace it at an authorized service center. Disconnect the power cord from the shaver when removing the battery. Perform steps 1 to 5 and lift the battery, and then remove it. English For environmental protection and recycling of materials This shaver contains a Lithium-ion battery. Please make sure that the battery is disposed of at an officially assigned location, if there is one in your country. 14

15 Specifications Product name Product model Rated input AC/Rechargeable Shaver ES-GA V 50-60Hz 180mA Rated output 5.4V 1.2A Motor voltage 3.6V Charging time Approx. 1 hour Place of origin Main body: Japan Adaptor: China Date of production See engraving on the commodity. Execution standard Chinese standard GB appendix B GB This product is intended for household use only. English 15

16 进口商 : 松下电工 ( 中国 ) 有限公司地址 : 北京市朝阳区建国路 79 号华贸中心 2 号写字楼 6 层 7 层 703 室电话 : 邮政编码 : 制造商 : 松下电工株式会社地址 : 日本大阪府门真市大字门真 1048 番地 Panasonic Electric Works Co., Ltd. 1048, Oaza Kadoma, Kadoma shi, Osaka , Japan F CH, EN 日本印刷 Printed in Japan ES9700GA203K Y 发行 :2010 年 5 月

ES-GA20_CH.indb

ES-GA20_CH.indb 使用说明书 Operating Instructions ( 家用 ) 电动剃须刀 (Household) AC/Rechargeable Shaver 型号 Model No. ES GA20 中文 2 English 9 在使用本产品前, 请仔细阅读本说明书并妥善保管, 以备将来参考 Before operating this unit, please read these instructions