Quick Start Guide 54-Port 0G/40G Fiber Ethernet Switch AS570-54X AS57-54X AS58-54X. Unpack the Switch and Check Contents Use the screws and cage nuts supplied with the rack to secure the switch in the rack. AS570-54X, AS57-54X or AS58-54X Rack Mounting Kit front-post brackets, rear-post brackets, 0 screws, and ear-locking screws Power Cord (included with AC PSUs only) Caution: Installing the switch in a rack requires two people. One person should position the switch in the rack, while the other secures it using the rack screws. 装置の吸排気に必要な領域をマニュアル上に規定している. Adjust Rear-Post Bracket Ears Ground Wire (included with DC PSUs only) Console Cable RJ-45 to DB-9 DC Power Cable (included with 48 VDC PSU only) Documentation Quick Start Guide (this document) and Safety and Regulatory Information Note: The switch has the Open Network Install Environment (ONIE) software installer pre-loaded on the switch, but no switch software image. Information about compatible switch software can be found at www.edge-core.com. Caution: The switch includes plug-in power supply (PSU) and fan tray modules that are installed into its chassis. All installed modules must have a matching airflow direction. That is, if the installed power modules have a front-to-back (FB) airflow direction, all the installed fan tray modules must also have a FB airflow direction. Lock the position of the rear-post bracket ears using the included position-locking screws. You can also adjust the rear-post bracket ears to fit different rack depths from 56 cm to 75 cm. 4. Ground the Switch Note: The switch drawings in this document are for illustration only and may not match your particular switch model.. Attach the Brackets Ensure the rack is properly grounded and in compliance with ETSI ETS 00 5. Verify that there is a good electrical connection to the grounding point on the rack (no paint or isolating surface treatment). Attach the grounding wire #4 AWG to the grounding point on the switch rear panel. Then connect the other end of the wire to rack ground. For details on grounding the switch with a VDC PSU in an Open Rack, refer to the Edgecore ORSA-U Open Rack Tray Set Installation Guide. Caution: The earth connection must not be removed unless all supply connections have been disconnected. Attach each of the front- and rear-post brackets to the switch using four of the included bracket screws. Use an additional two screws to secure each of the rear-post brackets at the mid-point on the sides of the switch. www.edge-core.com E06-AP-R06 50000064A
Quick Start Guide 5. Connect Power Boot the switch. Wait for the ONIE software to locate and execute the NOS installer, and then wait for the installer to load the NOS software image. Subsequent switch boots will bypass ONIE and directly run the NOS software. Note: For switches with ONIE software pre-loaded, refer to the network operating system (NOS) installer and NOS documentation for details on software options and set up for ONIE. Install one or two AC or DC power modules in the switch. The switch supports up to two PSUs that must have the same matching airflow direction as the installed fan tray. Connect an external AC or DC power source to the modules. 8. Connect Network Cables 6 75 VDC Return (blue wire) Chassis Ground (yellowgreen wire) -6-75 VDC (brown wire) 4 Open Rack tray connector for VDC PSU Caution: Use a UL/IEC/EN 60950- certified power supply to connect to a DC converter, and a #4 AWG (for 6 75 VDC PSU) or #0 AWG (for VDC PSU) wire to connect to a DC PSU. 6. Verify Switch Operation 4 For the RJ-45 Management port, connect 00-ohm Category 5, 5e or better twisted-pair cable. Connect DAC cables to the SFP+/QSFP+ slots. Or first install SFP+/QSFP+ transceivers and then connect fiber optic cabling to the transceiver ports. The following transceivers are supported: 40GBASE-CR4 40GBASE-SR4 0GBASE-CR 0GBASE-SR (ET540-SR) 000BASE-SX (ET40-SX) 000BASE-LX (ET40-LX) Note: As connections are made, check the port status LEDs to be sure the links are valid. 9. View the Product Label (For AS57-54X/AS58-54X only) Verify basic switch operation by checking the system LEDs. When operating normally, the PSU/PSU, Diag, and Fan LEDs should all be on green. 7. Perform Initial System Boot If the network operating system (NOS) installer is located on a network server, first connect the RJ-45 Management (Mgmt) port to the network using 00-ohm Category 5, 5e or better twisted-pair cable. (Not required if the NOS installer is located on attached storage.) The switch product label is located below SFP+ ports 7 on left side of the front panel. Pull the label out to view the product information.
Quick Start Guide Hardware Specifications Switch Chassis Size (WxDxH) Weight 48.4 x 47 x 4.4 mm (7.6 x 8.6 x.7 inches) AS570-54X / AS57-54X: 8.87 kg (9.56 lb), with two installed PSUs AS58-54X: 8.95 kg (9.7 lb), with two installed PSUs Temperature Operating: 0 C to 40 C ( F to 04 F) Storage: -40 C to 70 C (-40 F to 58 F) Humidity Power Consumption Operating: 5% to 95% (non-condensing) 8 Watts maximum AC PSU Power Rating AC Input DC Output 00 40 VAC, 50-60 Hz, 400 Watts 00 40 VAC, 50-60 Hz, 6 A 5 VSB @ A, VDC @ A 48 VDC PSU Power Rating DC Input DC Output 48 VDC, 400 Watts 6 75 VDC, 6 A maximum 5 VDC @ 0.5 A, VDC @ A VDC PSU (PSU-V-650) DC Input VDC (from Open Rack busbar) Regulatory Compliances Emissions Immunity Safety EN 550:00 +AC:0, Class A AS/NZS CISPR : 009+A: 00, Class A CISPR :008, Class A EN 6000--:04, Class A EN 6000--:0 FCC Class A VCCI Class A CE Mark CCC GB 954-008, Class A BSMI EMI Standard CNS 48:006 EN 5504:00+A:05 IEC 6000-4-:008 ED..0 IEC 6000-4-:00 ED.. IEC 6000-4-4:0 ED..0 IEC 6000-4-5:04 ED..0 IEC 6000-4-6:0 ED. 4.0 IEC 6000-4-8:009 ED..0 IEC 6000-4-:004 ED..0 UL (CSA. No 60950- & UL60950-) CB (IEC/EN60950-) CCC GB494.-0 BSMI Safety Standard CNS46-
AS570-54X AS57-54X AS58-54X 装置の吸排気に必要な領域をマニュアル上に規定している 4
4 4 / / 7 5
x x AC PSU 48 VDC PSU VDC PSU (PSU-V-650) 6
54 0G/40G AS570-54X AS57-54X AS58-54X. AS570-54X, AS57-54X AS58-54X x x x0 x AC PSU 装置の吸排気に必要な領域をマニュアル上に規定している. DC PSU RJ45 DB-9 DC 48 VDC PSU ONIE www.edge-core.com FB FB 56 cm 75 cm 4.. ETSI ETS 00 5 4 AWG VDC PSU Edgecore ORSA-U Open Rack Tray Set 7
5. ONIE NOS NOS ONIE NOS ONIE NOS NOS 8. AC DC PSU PSU AC DC RJ-45 00-ohm 5 5e 6 75 VDC Return Chassis Ground -6-75 VDC 4 VDC PSU DC Converter UL/IEC/EN 60950- DC PSU #4 AWG 6 VDC 75 VDC PSU #0 AWG VDC PSU DC PSU 6. 4 DAC SFP+/QSFP+ 40GBASE-CR4 40GBASE-SR4 0GBASE-CR 0GBASE-SR (ET540-SR) 000BASE-SX (ET40-SX) 000BASE-LX (ET40-LX) LED 9. ( AS57-54X/AS58-54X ) LED PSU/PSU Diag LED 7. SFP+ 7- NOS 5-ohm 5 5e RJ-45 Mgmt NOS 8
(WxDxH) 48.4 x 47 x 4.4 mm (7.6 x 8.6 x.7 AS570-54X / AS57-54X: 8.87 kg (9.56 lb) PSU AS58-54X: 8.95 kg (9.7 lb) PSU : 0 C 40 C ( F 04 F) : -40 C 70 C (-40 F 58 F) : 5% 95% 8 AC PSU AC DC 00 40 VAC 50-60 Hz 400 00 40 VAC, 50-60 Hz, 6 A 5 VSB @ A, VDC @ A 48 VDC PSU DC DC 48 VDC 400 6 75 VDC 6 A 5 VDC @ 0.5 A, VDC @ A VDC PSU (PSU-V-650) DC VDC EN 550:00 +AC:0, Class A AS/NZS CISPR : 009+A:00, Class A CISPR :008, Class A EN 6000--:04, Clas A EN 6000--:0 FCC Class A VCCI Class A CE Mark CCC GB 954-008, Class A BSMI EMI Standard CNS 48:006 EN 5504:00+A:05 IEC 6000-4-:008 ED..0 IEC 6000-4-:00 ED.. IEC 6000-4-4:0 ED..0 IEC 6000-4-5:04 ED..0 IEC 6000-4-6:0 ED. 4.0 IEC 6000-4-8:009 ED..0 IEC 6000-4-:004 ED..0 UL (CSA. No 60950- & UL60950-) CB (IEC/EN60950-) CCC GB494.-0 BSMI Safety Standard CNS46-9