NORMAL CURRENT CONDITION UL type fuse: Max.current de-rating of fuse(in)= R.M.S current/(temp.factor) x UL margin(0.75 fixed) IEC type fuses: Max.curr

FUSES What are fuses? They are protectors that prevent electronic and electrical equipment from overload current damage.current flew to circuit via fuse until over the specifications of fuse.at That time, the fuse "Blows" and stops the current. FUSE TYPE There are four basic types of fuses: (1)Slow Blow/Time lag fuses ()Dual element slow blow fuses (3)Fast acting fuses (4)Very fast acting fuses Slow-blow fuses are ideal for circuits with a transient surge or power-on inrush.these circuits include:motors,transformers, incandescent lamps and capacitate loads. Fast-acting fuses response quickly and are used in circuits without transient inrush currents. Very fast-acting fuses often have silver linked. Because the fuses need to have ability to limit the current,these fuses are usually used to protect semiconductor circuits. FUSE SELECTION GUIDE The fuse must carry the normal load current of the circuit without nuisance openings.however,when an over current occurs the fuse must interrupt the over current,limit the energy let-through,and withstand the voltage across the fuse during acting.to properly select a fuse the followings must be considered: (1)Normal operating current(the current rating of a fuse is typically derated 5% for operation at 5% to avoid nuisance blowing.for example,a fuse with 10A current rating is not usually recommended for operation at more than 7.5A in a 5% derating.) ()Overload current and melting time of the fuse. (3)Application volage(ac or DC voltage). (4)Inrush currents,surge currents,pulses,start-up currents characteristics. (5)Ambient temperature. (6)Applicable standards agency required,such as UL,CSA, TUV,VDE,PSE and IEC... Considerations: Reduce installed cost,ease of removal, (7)mounting type/form factor,etc. Electrical Characteristic The capacity of fuses for carrying current are tested at 5 and will be affected by ambient temperature changed.the fuse operated in higher the ambient temperature;the life of the fuse will be reduced. Conversely,operating at a lower temperature wil extend the life of fuse.

NORMAL CURRENT CONDITION UL type fuse: Max.current de-rating of fuse(in)= R.M.S current/(temp.factor) x UL margin(0.75 fixed) IEC type fuses: Max.current de-rating of fuse(in) = measured rms current/(temp.factorx IEC margin(0.9 fixed)) PERCENT RATING 10 110 100 90 CHART SHOWING EFFECT OF AMBIENT TEMPERATURE ON CURRENT-CARRYING CAPACITY 80 70 60-60 -40-0 0 0 40 60 80 100 10 140-76 -40-4 3 68 104 BREAKING CAPACITY A fuse will be safely interrupt in the maximum current and the maximum rated voltage(include less than maximum rated) then the appearance of fuse will not be changed. VOLTAGE RATING For general circuit protetion,the voltage rating of the circuit needs to be equal or less than the voltage rating of the fuse. Using exceed the voltage rating of the fuse in circuit will reduce ability of the fuse for clearing overload current safely.for example, fuse 50V voltage rating can be used in less than 50V circuits. AMPERE SQUARE SECONDS, I t Ii is the measure of heat energy developed within a circuit during the fuse's clearing.it can be expressed as "melting I t ","arcing I t " or the sum of them as " Clearing I t "."I" stands for effective let-through current(rms),which is squared, and "t" means melting time(seconds). I t I t I t I t

CALCULATING PULSE I t I t The energy contained in a current pulse depends on the Pulse s waveform s shape, peak current and duration. Determini the energy contained in a particular waveform can be very difficult. Table 1 presents a variety of waveforms and the corresponding formulas which determine I t value. Current pulses in most applications can be approximated by one of the waveforms in Table 1. If a complex waveform is not shown exactly, then it may be possible to break the com-plex waveform in to a combination of the simpler waveforms shown. The complex waveform s I t is then estimated as the sum of the I t values of these other waveforms. The best way to explain how this is done is through an example. Table 1 Waveform I t Formulas Pulse Waveforms Formulas 1 a t b 1 (i a I t= +i ai b+i b )t 3 ip t 1 I t= i p t 3 3 ip t 1 I t= i p t 4 ip t I t=i p t 5 ip t I t= i p t 1 6 ip t OR t I t= i p t 5 1 Table 1 Waveform I t Formulas Pulse Cycle Withstand Capability 100,000 Pulses Pulse I t=% Of Nominal Melting I t 10,000 Pulses Pulse I t=9% Of Nominal Melting I t 1,000 Pulses Pulse I t=38% Of Nominal Melting I t 100 Pulses Pulse I t=48% Of Nominal Melting I t

100000 100000 10000 10000 Number of Pulses 1000 Number of Pulses 1000 100 10% Table Pulse I t / Average Melting I t 100% Note: Adequate time(10 seconds) must exist between pulse events to allow heat from the previous event to dissipate. Example: Select one fuse Type: MET(page 4) is capable of withstanding 100,000 pulses cycle. The normal operating current is A at an ambient temperature of 5ºC and waveform shown in Figure 1. 10A/div 100 10% Table Pulse I t / Average Melting I t 10A/div 100% ip=55a ip=55a Figure 1 t=6ms ms/div t=6ms ms/div Answer: Step1. Refer to table 1 and select suitable pulse waveforms and formulas to calculate I t. I t = 1/3 (ip) t = 1/3 x (55) x 6 1000 = 6.05A Sec This value is referred to as the Pulse I t Step. Refer to table decide Nominal Melting I t. 100,000 Pulses Pulse I t =% Of Nominal Melting I t So: Normal Melting I t = Pulse I t 0. = 6.05 0. = 7.5 A Sec Step 3. Examine the I t rating data for the Time lag radial lead micro fuse. The part number MET, ampere design is rated at 31A Sec, which is the minimum fuse rating that will accommodate the 7.5 A Sec calculated in Step. I t I t = 1/3 (ip) t = 1/3 x (55) x 6 1000 = 6.05A Sec I t I t I t I t I t = Pulse I t 0. = 6.05 0. = 7.5 A Sec I t Sec Sec

VICFUSE circuit protection design combines miniature Fuses,Fuse Bases and Fuse-Carriers.We provide to you good combinations according to your different demands.for example,a fuse clip or holder is suitable for fuse without lead wire connect with pcb,it's easy for user change and fix it. The Fuse-Holder must be thinking about the maximum energy dissipation (temperature raise) of the application and must check especially in installment about the temperature raise in the maximum ambient temperature. Please ask for further detailed information for choice and application of our Fuse-Links. RETURN OF GOODS Return of unused merchandise is permitted within 30 days after shipment only,with freight and duty paid.a returning fee equal to 15% of the original sales price (minimum of US $100)will be charged for this service,consult with sales department for authorization prior to returning merchan dise for credit or replacement.an authorization number must be appeared on all packages returned or they will not be accepted. VICFUSE Components are guaranteed from defects in material and workmanship for a reason able period of time after delivery. Our liability shall be limited to replacement to defective material only. Either seller or manufacturer shall be liable for any injury,loss or damage,direct or consequential,rising out of the use of or the inability to use the products. Before using,user shall determine the suitability of the product for his intended use,user assumes all risk and liability whatsoever in connection therewith. VICFUSE reserves the right to change specifications on any and all items shown in this catalog.

FUSE SELECTION 01-05 INDEX 06-07 PRODUCT TYPE CHARACTERISTICS A V SURFACE MOUNT FUSE F SEF 6mA-5A 15V,86V 08-09 T SET 00mA-7A 15V 10-11 C TYPE CHIP FUSE F CQ40LF 500mA-40A 600V 1-13 T CQ40LT 500mA-40A 600V 14-15 F CQ4LF 1A-0A 350V 16-17 T CQ4LT 1A-0A 350V FF CQ1LV 1A-0A 15V,4V T CQ1LH 1A-0A 15V,4V F CQ1LF 1A-0A 15V,4V T CQ1LT 1A-0A 15V,4V F CQ06LF 1A-8A 63V T CQ06LT 1A-8A 63V P TYPE CHIP FUSE F CQ4PF 500mA-1A 350V T CQ4PT 500mA-1A 350V F CQ1PF 500mA-7A 63V T CQ1PT 500mA-7A 63V F CQ06PF 500mA-5A 63V T CQ06PT 500mA-5A 63V THIN FILM CHIP FUSE H CF1 500mA-7A 63V,3V H CF06 400mA-5A 50V,3V H CF04 315mA-4A 3V F CFS1 500mA-7A 63V,3V F CFS06 400mA-6A 50V,3V F CFS04 500mA-4A 3V F CP1 500mA-7A 63V,3V 18-19 0-1 -3 4-5 6-7 8-9 30-31 3-33 34-35 36-37 38-39 40-41 4-43 44-45 46-47 48-49 50-51 5-53 54-55 56-57 F CP06 500mA-5A 50V,3V 58-59 F CP04 500mA-4A 3V 60-61 T CPS1 500mA-7A 63V,3V 6-63 T CPS06 500mA-6A 50V,3V 64-65 PPTC RESETABLE FUSE PPTC SMD 90 0.3A-3A 6V-60V 66-68 PPTC SMD 181 PPTC SMD 110 PPTC SMD 106 PPTC SMD 0805 PPTC SMD 0603 PPTC LO RHO SMD 181 PPTC LO RHO SMD 110 PPTC LO RHO SMD 106 PPTC LO RHO SMD 0805 PPTC LO RHO SMD 0603 0.1A-3A 0.05A-A 0.05A-A 0.1A-1A 0.01A-0.A 1.4A-3.7A 1.75A-3.80A 0.5A-A 0.75A-1.75A 0.5A-0.75A 6V-60V 6V-60V 6V-60V 6V-15V 9V-60V 6V 6V 6V 6V 6V-9V 69-7 73-75 76-78 79-81 8-84 85-87 88-90 91-93 94-96 97-99

VICFUSE(CQ) BUSSMANN LITTELFUSE bel AEM SEF 615FA 451/453 SSQ AF 410 SET 615TD 45/454 SST CQ40LF - - - CQ40LT - 456 - CQ4LF - - - CQ4LT - - - CQ1LV - - - CQ1LH - - - CQ1LF 316FF 466/437/433/49 C1Q F106FA CQ1LT 316TD 469/430/468 C1S F106SB CQ06LF 0603FA 467/438/434/431 CQ F0603FA CQ06LT - - - F0603SB CQ4PF - - - CQ4PT - - - CQ1PF - - - CQ1PT - - - CQ06PF - - - CQ06PT - - - CF1 - - - CF06 - - - CF04 - - - CFS1 - - - CFS06 - - - CFS04 - - - CP1 - - - CP06 - - - CP04 - - - CP04 - - - CPS1 - - - CPS06 - - - PPTC SMD 90 - - - Raychem/Tyco Bourns PPTC SMD 181 - - - PPTC SMD 110 - - - PPTC SMD 106 - - - PPTC SMD 0805 - - - PPTC SMD 0603 - - - PPTC LO RHO SMD 181-181L - PPTC LO RHO SMD 110-110L - PPTC LO RHO SMD 106-106L - PPTC LO RHO SMD 0805 - - - PPTC LO RHO SMD 0603 - - - minismd microsmd nanosmd MF-MSMD(F) MF-USMD(F) MF-NSMD(F)

Type SEF Fast Acting Square Ceramic Surface Mount Fuse Feature a. Small volume. b. Excellent inrush current withstanding capability. c. Excellent withstand capacity for thermal and mechanic shock. d. High reliability and stable solderability, terminal caps can choice plating gold or silver. e. Our SEF SET series products,because the materials used in these fuses include high melting temperature type solder and this solder contains more than 85% lead (Pb),so these products can conform to the exempts of the requirements of RoHS Directive(00/95/EC). Cartridge Catalog Number SEF.06 Approval PSE Certified products for U.S. and Canada Recognized Component for Canada and U.S. CSA Listed Electrical Characteristic Rated current Ampere [ In ] 6mA (1/16A) 1 ln ln MIN MAX 6mA~10A 4hr 5 sec 1A~15A 4hr 60 sec Environmental Temperature at 5 C Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 11.75 0.000961 SEF.080 80 ma 9.9550 0.001000 SEF.100 100 ma 9.5130 0.001500 SEF.15 15 ma 5.8395 0.00310 SEF.00 00 ma.0195 0.008000 SEF.50 50 ma 1.1050 0.009380 SEF.300 300 ma 0.8554 0.018000 SEF.375 375 ma 0.7819 0.01100 SEF.400 400 ma 0.500 0.03000 SEF.500 500 ma 0.4895 0.037500 SEF.700 700 ma 0.814 0.10500 SEF.750 750 ma 0.45 0.153100 SEF 001 1 A 15V 0.1407 0.385000 SEF 1.50 1.5 A 0.1130 0.75000 SEF 00 A 0.0594 0.894000 SEF.50.5 A 0.0384 1.18000 SEF 003 3 A 0.0333 1.475000 SEF 3.15 3.15A 0.096 1.655000 SEF 3.50 3.5 A 0.068.055000 SEF 004 4 A 0.009 3.88000 SEF 005 5 A 0.0179 5.480000 SEF 006 6 A 0.0117 8.50000 SEF 007 7 A 0.0104 9.931000 SEF 008 8 A 0.0095 18.8000 SEF 010 10 A 0.0067.50000 SEF 01 1A 0.004 43.0000 SEF 015 15A 86V 0.005 11.5000 SEF 00 0A SEF 05 5A 1A~15A 6mA~5A 6A~5A 6mA~10A Interrupting 6mA~8A: 1A~5A: 50 amperes at 15V AC/DC 300 amperes at 3V DC 10A: 35 amperes at 15V AC 50 amperes at 15V AC/DC 300 amperes at 3V DC 50 amperes at 65V AC/DC 300 amperes at 4V DC 00 amperes at 86V AC/DC Mechanical Dimension Physical Specification Material Body: Ceramic Terminations: Silver Plated Brass Caps -G:Gold plated brass caps Packaging 1,000 Fuses in 7 inches dia. reel, or 5,000 fuses in 13 inches dia. reel, 1mm wide tape, per EIA Standard 481 Environmental Specification Operating Temperature -55 C to +15 C Vibration MIL-STD-0G, Method 01 (10-55 Hz, 0.06 inch, total excursion) Salt Spray MIL-STD-0G, Method 101, Test Condition B (48Hrs) Insulation Resistance MIL-STD-0G, Method 30, Test Condition A Resistance to Solder Heat MIL-STD-0G, Method 10, Test Condition B (10sec, at 60 C) Thermal Shock MIL-STD-0G, Method 107, Test Condition B (-65 C to +15 C).6 ± 0.1 mm

Temperature Temperature Rerating Curve Average Time Current Curves Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Time in Seconds 100000 10000 1000 100 10 1 0.1 0.01 0.01 0.1 1 10 100 1000 CURRENT IN AMPERES 6mA 80mA 100mA 15mA 00mA 50mA 300mA 375mA 400mA 500mA 700mA 750mA 1A 1.5A A.5A 3A 3.5A 4A 5A 6A 7A 8A 10A 1A 15A Soldering Parameters Reflow Condition - Temperature Min (T s(min) ) 150 C Pb Free assembly T P Ramp-up t P Critical Zone TL to TP Pre Heat - Temperature Max (T s(max) ) 00 C - Time (Min to Max) (t s ) 60 10 secs T L T S(max) t L Average ramp up rate (Liquidus Temp (T L ) to peak 5 C/second max. T S(min) Preheat Ramp-down T S(max) to T L - Ramp-up Rate 5 C/second max. t S - Temperature (T L ) (Liquidus) 17 C Reflow - Temperature (t L ) 60 90 seconds Peak Temperature (T P ) 50 +0/-5 C 5 time to peak temperature (t 5ºC to peak) Time Time within 5 C of actual peak Temperature (t p ) 0 40 seconds Ramp-down Rate 5 C/second max. Time 5 C to peak Temperature (T P ) 8 minutes max. Do not exceed 60 C Wave Soldering Parameters 60 C Peak Temperature, 10 seconds max. 6.86 (.70") 3.15 (.14") SEF 001 1.96 (.077").95 (.116") Recommended pad layout SERIES AMP Code Refer to Electrical

Type SET Slow Blow Square Ceramic Surface Mount Fuse Feature a. Small volume. b. Excellent inrush current withstanding capability. c. Excellent withstand capacity for thermal and mechanic shock. d. High reliability and stable solderability, terminal caps can choice plating gold or silver. e. Our SEF SET series products,because the materials used in these fuses include high melting temperature type solder and this solder contains more than 85% lead (Pb),so these products can conform to the exempts of the requirements of RoHS Directive(00/95/EC). Cartridge Catalog Number SET.00 Approval PSE 1A~7A UL Recognized 00mA~7A CSA Listed 00mA~7A Electrical Characteristic Rated current Ampere [ In ] 00 ma 1 ln ln 3 ln 8 ln MIN MIN MAX MIN MAX MIN MAX 00mA~7A 4hr 1 sec 60 sec 0. sec 3 sec 0.0 sec 0.1 sec Environmental Temperature at 5 C Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 1.5751 0.0600 SET.50 50 ma 1.585 0.0680 SET.300 300 ma 1.51 0.0900 SET.350 350 ma 0.9366 0.1000 SET.375 375 ma 0.53 0.109 SET.400 400 ma 0.5150 0.400 SET.450 450 ma 0.5009 0.3037 SET.500 500 ma 0.391 0.3750 SET.700 700 ma 0.648 0.4900 SET.750 750 ma 0.1600 0.660 SET 001 1 A 15V 0.1090 1.9090 SET 1.50 1.5 A 0.0511 3.8350 SET 00 A 0.0550 8.5600 SET.50.5 A 0.087 16.550 SET 003 3 A 0.08.540 SET 3.15 3.15 A 0.04 3.000 SET 3.50 3.5 A 0.0190 9.400 SET 004 4 A 0.0140 35.80 SET 005 5 A 0.0130 54.800 SET 006 6 A 0.0090 64.800 SET 007 7 A 0.0074 89.830 Interrupting 50 amperes at 15V AC/DC 300 amperes at 3V DC Mechanical Dimension Physical Specification Material Body: Ceramic Terminations: Silver Plated Brass Caps -G:Gold plated brass caps Packaging 1,000 Fuses in 7 inches dia. reel, or 5,000 fuses in 13inches dia. reel, 1mm wide tape, per EIA Standard 481 Environmental Specification Operating Temperature -55 C to +15 C Vibration MIL-STD-0G, Method 01 (10-55 Hz, 0.06 inch, total excursion) Salt Spray MIL-STD-0G, Method 101, Test Condition B (48Hrs) Insulation Resistance MIL-STD-0G, Method 30, Test Condition A Resistance to Solder Heat MIL-STD-0G, Method 10, Test Condition B (10sec, at 60 C) Thermal Shock MIL-STD-0G, Method 107, Test Condition B (-65 C to +15 C).6 ± 0.1 mm 47

Temperature Temperature Rerating Curve Average Time Current Curves Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Time in Seco 100000 10000 1000 100 10 1 0.1 0.01 0.1 1 10 100 00mA 50mA 300mA 350mA 375mA 400mA 450mA 500mA 700mA 750mA 1A 1.5A A.5A 3A 3.5A 4A 5A 6A 7A CURRENT IN AMPERES Soldering Parameters Reflow Condition - Temperature Min (T s(min) ) 150 C Pb Free assembly T P Ramp-up t P Critical Zone TL to TP Pre Heat - Temperature Max (T s(max) ) 00 C - Time (Min to Max) (t s ) 60 10 secs T L T S(max) t L Average ramp up rate (Liquidus Temp (T L ) to peak 5 C/second max. T S(min) Preheat Ramp-down T S(max) to T L - Ramp-up Rate 5 C/second max. t S - Temperature (T L ) (Liquidus) 17 C Reflow - Temperature (t L ) 60 90 seconds Peak Temperature (T P ) 50 +0/-5 C 5 time to peak temperature (t 5ºC to peak) Time Time within 5 C of actual peak Temperature (t p ) 0 40 seconds Ramp-down Rate 5 C/second max. Time 5 C to peak Temperature (T P ) 8 minutes max. Do not exceed 60 C Wave Soldering Parameters 60 C Peak Temperature, 3 seconds max. 6.86 (.70") 3.15 (.14") SERIES SET 001 47 1.96 (.077").95 (.116") Recommended pad layout AMP Code Refer to Electrical

Type CQ40LF 10.1mmx 3.1mm (401) Fast-Acting Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 1A ~30A Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Recommended Land Pattern Cartridge Catalog Number CQ40LF.500 CQ40LF1.5 CQ40LF00 CQ40LF00 CQ40LF030 CQ40LF040 Approval UL Recognized 1A~30A Ampere [ In ] 500 ma 1.5A A 0A 30A 40A Electrical Characteristic Voltage ( V ) 600V AC 350V DC Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.3510.300 0.0750 17.000 0.0560 37.000 0.0050 30.000 0.005 96.000 0.0019 600.000 Tape and Reel Specification Item W P E F P D D1 Criterion 16.00 8.00 1.75 7.50.00 1.50 1.50 Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Reflow Solder L1 L W 1A~30A 3.5 6.1 3.43 Rated current 1 ln ln MIN MAX 1A~30A 4 hr 5 sec Item P0 10P0 A0 B0 K0 t Criterion 4.00 40.00 3.5 10.58 1.50 0.30 Tolerence ±0.10 ±0.0 ±0.10 ±0.10 ±0.10 ±0.05 Environmental Temperature at 5 C Interrupting 1A~30A : 150 amperes at 350V DC 150 amperes at 600V AC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Tape & Reel Quantity 1000 pcs/reel Environmental Specification Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

Temperature Temperature Rerating Curve Average Time Current Curves 10 110 100 90 80 70 60-60 -40-0 0 0 40 60 80 100 10 140-76 -40-4 3 68 104 Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Soldering Parameters Reflow Condition - Temperature Min (T s(min) ) 150 C Pb Free assembly T P Ramp-up t P Critical Zone TL to TP Pre Heat - Temperature Max (T s(max) ) 00 C - Time (Min to Max) (t s ) 60 10 secs T L T S(max) t L Average ramp up rate (Liquidus Temp (T L ) to peak 5 C/second max. T S(min) Preheat Ramp-down T S(max) to T L - Ramp-up Rate 5 C/second max. t S Reflow - Temperature (T L ) (Liquidus) 17 C - Temperature (t L ) 60 90 seconds Peak Temperature (T P ) 50 +0/-5 C 5 time to peak temperature (t 5ºC to peak) Time Time within 5 C of actual peak Temperature (t p ) 0 40 seconds Ramp-down Rate 5 C/second max. Time 5 C to peak Temperature (T P ) 8 minutes max. Do not exceed 60 C Wave Soldering Parameters 60 C Peak Temperature, 10 seconds max. CQ40LF 001 SERIES AMP Code Refer to Electrical

Type CQ40LT 10.1mmx 3.1mm (401) Slow Blow Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 0.5A ~40A Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Recommended Land Pattern Cartridge Catalog Number CQ40LT001 CQ40LT00 CQ40LT00 CQ40LT030 CQ40LT040 Ampere [ In ] 1A A 0A 30A 40A Voltage ( V ) 600V AC 350V DC Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.8500 0.5800 0.4000 1.1100 0.0060 3.630 0.0030 136.89 0.0014 547.10 L1 L W 1A~30A 3.5 6.1 3.43 Approval UL Recognized 0.5A~40A Electrical Characteristic Rated current Environmental Temperature at 5 C Interrupting 0.5A~30A: 150 amperes at 350V DC 150 amperes at 600V AC 600 amperes at 60V DC 40A : 600 amperes at 60V DC Soldering Method 1 ln ln 3 ln 8 ln MIN MIN MAX MAX MAX 0.5mA~40A 4hr 1 sec 60 sec 3 sec 0.1 sec *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Tape and Reel Specification Item W P E F P D D1 Criterion 16.00 8.00 1.75 7.50.00 1.50 1.50 Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Item P0 10P0 A0 B0 K0 t Criterion 4.00 40.00 3.5 10.58 1.50 0.30 Tolerence ±0.10 ±0.0 ±0.10 ±0.10 ±0.10 ±0.05 Reflow Solder Tape & Reel Quantity 1000 pcs/reel Environmental Specification Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

Temperature Temperature Rerating Curve Average Time Current Curves 10 110 100 90 80 70 60-60 -40-0 0 0 40 60 80 100 10 140-76 -40-4 3 68 104 Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Soldering Parameters Reflow Condition - Temperature Min (T s(min) ) 150 C Pb Free assembly T P Ramp-up t P Critical Zone TL to TP Pre Heat - Temperature Max (T s(max) ) 00 C - Time (Min to Max) (t s ) 60 10 secs T L T S(max) t L Average ramp up rate (Liquidus Temp (T L ) to peak 5 C/second max. T S(min) Preheat Ramp-down T S(max) to T L - Ramp-up Rate 5 C/second max. t S - Temperature (T L ) (Liquidus) 17 C Reflow - Temperature (t L ) 60 90 seconds Peak Temperature (T P ) 50 +0/-5 C 5 time to peak temperature (t 5ºC to peak) Time Time within 5 C of actual peak Temperature (t p ) 0 40 seconds Ramp-down Rate 5 C/second max. Time 5 C to peak Temperature (T P ) 8 minutes max. Do not exceed 60 C Wave Soldering Parameters 60 C Peak Temperature, 10 seconds max. CQ40LT 001 SERIES AMP Code Refer to Electrical

Type CQ4LF 6.1mmx.6mm (410) Fast-Acting Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 1A ~0A Catalog Number Approval Ampere [ In ] 1 A Voltage ( V ) Nominal Resistance Cold Ohms Nominal Melting I t A Sec CQ4LF 001 1.100 0.500 CQ4LF 1.50 1.5A 0.500 1.130 CQ4LF 00 A 0.03 1.00 CQ4LF.50.5 A 0.155 1.500 CQ4LF 003 3 A 0.045 1.890 CQ4LF 3.15 3.15A 0.039.80 CQ4LF 3.50 3.5 A 0.036.573 CQ4LF 004 4A 0.08 3.360 CQ4LF 005 5A 350V 0.01 6.000 CQ4LF 006 6A 0.016 7.90 CQ4LF 6.30 6.3A 0.015 9.18 CQ4LF 007 7A 0.014 1.5 CQ4LF 008 8A 0.013 16.00 CQ4LF 010 10A 0.011 5.00 CQ4LF 01 1A 0.009 36.00 CQ4LF 015 15A 0.006 67.50 CQ4LF 00 0A 0.005 13.0 Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Tape and Reel Specification Item W P E F P D D1 Criterion 1.00 4.00 1.75 5.50.00 1.50 1.00 Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Item P0 10P0 A0 B0 K0 t Criterion 4.00 40.00.85 6.30 1.45 0.4 Tolerence ±0.10 ±0.0 ±0.10 ±0.10 ±0.10 ±0.05 Recommended Land Pattern L1 L W 1A~0A 1.96.95 3.15 Reflow Solder UL Recognized 1A~0A Electrical Characteristic Rated current 1 ln ln MIN MAX 1A~0A 4 hr 5 sec Environmental Temperature at 5 C Interrupting 1A~0A : 100 amperes at 350V AC 100 amperes at 15V AC 100 amperes at 15V DC 300 amperes at 3V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Tape & Reel Quantity Environmental Specification 500 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

Temperature Rerating Curve Average Time Current Curves 10 110 100 90 80 70 60-60 -40-0 0 0 40 60 80 100 10 140-76 -40-4 3 68 104 Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Time in Seconds (s) Current in Amperes (A) Soldering Parameters CQ4LF 001 SERIES AMP Code Refer to Electrical

Type CQ4LT 6.1mmx.6mm (410) Slow Blow Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 1A ~0A Catalog Number Approval Ampere [ In ] 1 A Voltage ( V ) Nominal Resistance Cold Ohms Nominal Melting I t A Sec CQ4LT 001 1.100 0.700 CQ4LT 1.50 1.5A 0.500 1.570 CQ4LT 00 A 0.03 1.800 CQ4LT.50.5 A 0.155.430 CQ4LT 003 3 A 0.045 3.40 CQ4LT 3.15 3.15A 0.039 3.770 CQ4LT 3.50 3.5 A 0.036 4.410 CQ4LT 004 4A 0.08 5.760 CQ4LT 005 5A 350V 0.01 9.750 CQ4LT 006 6A 0.016 13.3 CQ4LT 6.30 6.3A 0.015 15.08 CQ4LT 007 7A 0.014 19.60 CQ4LT 008 8A 0.013 5.60 CQ4LT 010 10A 0.011 40.00 CQ4LT 01 1A 0.009 57.60 CQ4LT 015 15A 0.006 101. CQ4LT 00 0A 0.005 19.0 Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Tape and Reel Specification Item W P E F P D D1 Criterion 1.00 4.00 1.75 5.50.00 1.50 1.00 Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Item P0 10P0 A0 B0 K0 t Criterion 4.00 40.00.85 6.30 1.45 0.4 Tolerence ±0.10 ±0.0 ±0.10 ±0.10 ±0.10 ±0.05 Recommended Land Pattern Reflow Solder L1 L W 1A~0A 1.96.95 3.15 UL Recognized 1A~0A Electrical Characteristic Rated 1 ln ln 3 ln 8 ln current MIN MIN MAX MAX MAX 1A~0A 4hr 1 sec 60 sec 3 sec 0.1 sec Environmental Temperature at 5 C Interrupting 1A~0A : 100 amperes at 350V AC 100 amperes at 15V AC 100 amperes at 15V DC 300 amperes at 3V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Tape & Reel Quantity Environmental Specification 500 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) 1A 1.5A A.5A 3A 3.5A 4A 5A 6A 7A 8A 10A 1A 15A 0A 10 110 100 90 80 70 60-60 -40-0 0 0 40 60 80 100 10 140-76 -40-4 3 68 104 Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Current in Amperes (A) Soldering Parameters CQ4LT 001 SERIES AMP Code Refer to Electrical

Type CQ1LV 3.1mmx 1.6mm (106) Very Fast-Acting Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 1A ~0A Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Recommended Land Pattern Catalog Number Approval Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.6 0.170 CQ1LV 001 H 1A CQ1LV 1.50 K 1.5A 0.11 0.50 CQ1LV 00 N A 0.065 0.300 CQ1LV.50 O.5A 0.030 0.470 CQ1LV 003 P 3A 0.06 0.70 CQ1LV 3.50 R 3.5A 15V 0.005 0.90 CQ1LV 004 S 4A 0.0155 1.10 CQ1LV 005 T 5A 0.0105 1.880 CQ1LV 006 U 6A 0.0088 3.060 CQ1LV 007 V 7A 0.0078 4.410 CQ1LV 008 W 8A 0.007 5.760 CQ1LV 010 10 10A 0.0055 11.500 CQ1LV 01 1 1A 0.0048.30 4V CQ1LV 015 15 15A 0.0038 33.750 CQ1LV 00 0 0A 0.006 60.000 Tape and Reel Specification Item W P E F P D D1 Criterion 8.00 4.00 1.75 3.50.00 1.55 1.00 Tolerence ±0.30 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Item P0 10P0 A0 B0 K0 t Criterion 4.00 40.00 1.95 3.65 0.87 0.0- Tolerence ±0.10 ±0.0 ±0.10 ±0.10 ±0.10 ±0.10 0.9 ± 0. mm Reflow Solder UL Recognized 1A~0A Electrical Characteristic Rated current Environmental Temperature at 5 C Interrupting 1A~8A : 50 amperes at 15V AC 50 amperes at 15V DC 100 amperes at 63V DC 150 amperes at 3V AC 10A~0A : 150 amperes at 4V DC Soldering Method 1 ln.5 ln 4 ln MIN MAX MAX 1A~0A 4 hr 5 sec 0.05 sec *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. 1.6 + 0.1mm Tape & Reel Quantity Environmental Specification 4000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability Reference IEC 68--58

Temperature Rerating Curve Average Time Current Curves 10 110 100 90 80 70 60-60 -40-0 0 0 40 60 80 100 10 140-76 -40-4 3 68 104 Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Soldering Parameters CQ1LV 001 SERIES AMP Code Refer to Electrical

Type CQ1LH 3.1mmx 1.6mm (106) Slow Blow Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 1A ~0A Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.59 0.50 CQ1LH 001 H 1A CQ1LH 1.50 K 1.5A 0.13 0.80 CQ1LH 00 N A 0.061 0.360 CQ1LH.50 O.5A 0.09 0.560 CQ1LH 003 P 3A 0.05 0.810 CQ1LH 3.50 R 3.5A 15V 0.019 1.100 CQ1LH 004 S 4A 0.014 1.80 CQ1LH 005 T 5A 0.010.10 CQ1LH 006 U 6A 0.0083 3.600 CQ1LH 007 V 7A 0.007 4.900 CQ1LH 008 W 8A 0.0065 6.400 CQ1LH 010 10 10A 0.005 1.500 CQ1LH 01 1 1A 0.0045 5.900 4V CQ1LH 015 15 15A 0.009 45.000 CQ1LH 00 0 0A 0.003 80.000 Approval Tape and Reel Specification Item W P E F P D D1 Criterion 8.00 4.00 1.75 3.50.00 1.55 1.00 Tolerence ±0.30 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Item P0 10P0 A0 B0 K0 t Criterion 4.00 40.00 1.95 3.65 0.87 0.0- Tolerence ±0.10 ±0.0 ±0.10 ±0.10 ±0.10 ±0.10 0.9 1.1 ± 0. mm Reflow Solder UL Recognized 1A~0A Electrical Characteristic Rated current 1 ln ln 3 ln 8 ln MIN MIN MAX MAX MAX 1A~0A 4hr 1 sec 10 sec 3 sec 0.05 sec Environmental Temperature at 5 C Interrupting 1A~8A : 50 amperes at 15V AC 50 amperes at 15V DC 100 amperes at 63V DC 150 amperes at 3V AC 10A~0A : 150 amperes at 4V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. 1.6 + 0.1mm Tape & Reel Quantity Environmental Specification 4000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability Reference IEC 68--58

Temperature Rerating Curve Average Time Current Curves 10 110 100 90 80 70 60-60 -40-0 0 0 40 60 80 100 10 140-76 -40-4 3 68 104 Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Soldering Parameters CQ1LH 001 SERIES AMP Code Refer to Electrical

Type CQ1LF 3.1mmx 1.6mm (106) Fast-Acting Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 1A ~0A Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Recommended Land Pattern Catalog Number Approval Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.614 0.053 CQ1LF 001 H 1A CQ1LF 1.50 K 1.5A 0.364 0.113 CQ1LF 00 N A 0.095 0.00 CQ1LF.50 O.5A 0.069 0.350 CQ1LF 003 P 3A 0.034 0.685 CQ1LF 3.50 R 3.5A 15V 0.07 0.735 CQ1LF 004 S 4A 0.03 1.15 CQ1LF 005 T 5A 0.017 1.67 CQ1LF 006 U 6A 0.013.340 CQ1LF 007 V 7A 0.011.75 CQ1LF 008 W 8A 0.009 3.50 CQ1LF 010 10 10A 0.008 6.35 CQ1LF 01 1 1A 0.007 7.90 4V CQ1LF 015 15 15A 0.0055 1.375 CQ1LF 00 0 0A 0.003 4.000 Tape and Reel Specification Item W P E F P D D1 Criterion 8.00 4.00 1.75 3.50.00 1.50 1.00 Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Item P0 10P0 A0 B0 K0 t Criterion 4.00 40.00 1.81 3.4 1.6 1.- Tolerence ±0.10 ±0.10 ±0.10 ±0.10 ±0.10 ±0.05 1.1 ± 0. mm Reflow Solder UL Recognized 1A~0A Electrical Characteristic Rated current Environmental Temperature at 5 C Interrupting 1A~8A : 50 amperes at 15V AC 50 amperes at 15V DC 100 amperes at 63V DC 150 amperes at 3V AC 10A~0A : 150 amperes at 4V DC Soldering Method 1 ln.5 ln 4 ln MIN MAX MAX 1A~0A 4 hr 5 sec 0.05 sec *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. 1.6 + 0.1mm Tape & Reel Quantity Environmental Specification 3000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

Temperature Rerating Curve Average Time Current Curves 1A 1.5A A.5A 3A 3.5A 4A 5A 6A 7A 8A 10A 1A 15A 0A 10 110 100 90 80 70 60-60 -40-0 0 0 40 60 80 100 10 140-76 -40-4 3 68 104 Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Time in Seconds (s) Current in Amperes (A) Soldering Parameters CQ1LF 001 SERIES AMP Code Refer to Electrical

Type CQ1LT 3.1mmx 1.6mm (106) Slow Blow Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 1A ~0A Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.400 0.115 CQ1LT 001 H 1A CQ1LT 1.50 K 1.5A 0.135 0.5 CQ1LT 00 N A 0.075 0.615 CQ1LT.50 O.5A 0.05 0.850 CQ1LT 003 P 3A 0.08 1.150 CQ1LT 3.50 R 3.5A 15V 0.05 1.635 CQ1LT 004 S 4A 0.00.300 CQ1LT 005 T 5A 0.014 5.100 CQ1LT 006 U 6A 0.010 6.350 CQ1LT 007 V 7A 0.009 7.515 CQ1LT 008 W 8A 0.0077 10.00 CQ1LT 010 10 10A 0.006 1.150 CQ1LT 01 1 1A 0.005 14.680 4V CQ1LT 015 15 15A 0.003 5.50 CQ1LT 00 0 0A 0.005 45.000 Approval Tape and Reel Specification Item W P E F P D D1 Criterion 8.00 4.00 1.75 3.50.00 1.50 1.00 Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Item P0 10P0 A0 B0 K0 t Criterion 4.00 40.00 1.81 3.4 1.6 1.- Tolerence ±0.10 ±0.10 ±0.10 ±0.10 ±0.10 ±0.05 1.1 ± 0. mm Reflow Solder UL Recognized 1A~0A Electrical Characteristic Rated current 1 ln ln 3 ln 8 ln MIN MIN MAX MAX MAX 1A~0A 4hr 1 sec 10 sec 3 sec 0.05 sec Environmental Temperature at 5 C Interrupting 1A~8A : 50 amperes at 15V AC 50 amperes at 15V DC 100 amperes at 63V DC 150 amperes at 3V AC 10A~0A : 150 amperes at 4V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. 1.6 + 0.1mm Tape & Reel Quantity Environmental Specification 3000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability

Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) 1A 1.5A A.5A 3A 3.5A 4A 5A 6A 7A 8A 10A 1A 15A 0A 10 110 100 90 80 70 60-60 -40-0 0 0 40 60 80 100 10 140-76 -40-4 3 68 104 Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Current in Amperes (A) Soldering Parameters CQ1LT 001 SERIES AMP Code Refer to Electrical

Type CQ06LF 1.6mmx 0.8mm (0603) Fast-Acting Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 1A ~8A Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.345 0.055 CQ06LF 001 H 1A CQ06LF 1.50 K 1.5A 0.160 0.115 CQ06LF 00 N A 0.066 0.160 CQ06LF.50 O.5A 0.039 0.350 CQ06LF 003 P 3A 0.07 0.655 CQ06LF 3.50 R 3.5A 63V 0.01 0.731 CQ06LF 004 S 4A 0.018 0.965 CQ06LF 005 T 5A 0.013 1.860 CQ06LF 006 U 6A 0.010.340 CQ06LF 007 V 7A 0.008.680 CQ06LF 008 W 8A 0.006 3.350 Approval UL Recognized 1A~8A Electrical Characteristic Tape and Reel Specification Item W P E F P D D1 Criterion 8.00 4.00 1.75 3.50.00 1.50 0.05 Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Item P0 10P0 A0 B0 K0 T Criterion 4.00 40.00 0.94 1.8 0.9 0. Tolerence ±0.10 ±0.0 ±0.10 ±0.10 ±0.10 ±0.05 0.8 ± 0. mm Reflow Solder Rated current 1 ln ln 3 ln 10 ln MIN MAX MAX MAX 1A~8A 4hr 5 sec 0.5 sec 0.0 sec Environmental Temperature at 5 C Interrupting 35 amperes at 63V DC 60 amperes at 3V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. 0.9 0.1mm + Tape & Reel Quantity Environmental Specification 4000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C 0.9 0.1mm +

Temperature Rerating Curve Average Time Current Curves 1A 1.5A A.5A 3A 3.5A 4A 5A 6A 7A 8A 10 110 100 90 80 70 60-60 -40-0 0 0 40 60 80 100 10 140-76 -40-4 3 68 104 Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Time in Seconds (s) Current in Amperes (A) Soldering Parameters CQ06LF 001 SERIES AMP Code Refer to Electrical

Type CQ06LT 1.6mmx 0.8mm (0603) Slow Blow Fuse Series Feature a. High voltage and high current rating b. High inrush and high breaking capacity c. Fast arcing extinguished d. Lead free & Halogen free material e. Good explosion proof f. Precise fusing time and cut-off completed g. Suitable for rated current of 1A ~8A Material Construction Body Material: Ceramic Termination Material: Silver(Ag),Nickel(Ni),Tin(Sn) Fuse Element: Silver(Ag) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.4 0.010 CQ06LT 001 H 1A CQ06LT 1.50 K 1.5A 0.100 0.018 CQ06LT 00 N A 0.060 0.350 CQ06LT.50 O.5A 0.07 0.690 CQ06LT 003 P 3A 0.0 0.850 CQ06LT 3.50 R 3.5A 63V 0.017 1.5 CQ06LT 004 S 4A 0.014.150 CQ06LT 005 T 5A 0.010.950 CQ06LT 006 U 6A 0.007 4.35 CQ06LT 007 V 7A 0.006 5.80 CQ06LT 008 W 8A 0.005 7.670 Approval UL Recognized 1A~8A Electrical Characteristic Tape and Reel Specification Item W P E F P D D1 Criterion 8.00 4.00 1.75 3.50.00 1.50 0.05 Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 Item P0 10P0 A0 B0 K0 T Criterion 4.00 40.00 0.94 1.8 0.9 0. Tolerence ±0.10 ±0.0 ±0.10 ±0.10 ±0.10 ±0.05 0.8 ± 0. mm Reflow Solder Rated current 1 ln ln 3 ln 10 ln MIN MIN MAX MAX MAX 1A~8A 4hr 1 sec 10 sec 3 sec 0.05 sec Environmental Temperature at 5 C Interrupting 35 amperes at 63V DC 60 amperes at 3V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. 0.9 0.1mm + Tape & Reel Quantity Environmental Specification 4000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C 0.9 0.1mm +

Temperature Rerating Curve Average Time Current Curves CQ 06LT Series Clear Time Curves 10 110 100 90 80 70 60-60 -40-0 0 0 40 60 80 100 10 140-76 -40-4 3 68 104 Note: 1. Derating depicted in this curve is in addition to the standard derating of 5% for continuous operation. Soldering Parameters CQ06LT 001 SERIES AMP Code Refer to Electrical

Type CQ4PF 6.1mmx.6mm (410) Fast-Acting Fuse Series Feature a. Chip Fuse structure design with PCB body and copper & tin alloy element b. Use optical lithography & etching skill to make refinement element c. Complete on element with the terminal electrode plating Tin material to prevent element oxidation. d. Product meet 100% ROHS, lead free, HF & REACH requirement. e. Offer range of current ratings from 0.5A-1A & voltage up to 350VAC and 350VDC. Material Construction Body Material: FR4 Board Termination Material: Copper(Cu),Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 1.050 0.150 CQ4PF.500 0.5A 500m A CQ4PF.750 0.75A 750mA 0.55 0.80 CQ4PF 001 1A 1A 0.100 0.400 CQ4PF 1.50 1.5 A 1.5 A 0.04 0.560 CQ4PF 00 A A 0.09 1.080 CQ4PF.50.5A.5A 0.03 1.500 CQ4PF 003 3 A 3 A 0.017 1.800 350V CQ4PF 004 4A 4A 0.01 3.00 CQ4PF 005 5A 5A 0.010 5.50 CQ4PF 006 6A 6A 0.008 7.00 CQ4PF 007 7A 7A 0.007 7.350 CQ4PF 008 8A 8A 0.006 9.600 CQ4PF 010 10A 10A 0.005 0.00 CQ4PF 01 1A 1A 0.004 8.80 Tape and Reel Specification Item W P E F P D D1 Criterion 1.00 4.00 1.75 5.50.00 1.50 1.00 Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 L1 L W 1A~0A 1.96.95 3.15 Reflow Solder Approval UL Recognized 0.5A~1A Electrical Characteristic Rated current 1 ln ln MIN MAX 0.5A~1A 4 hr 5 sec Environmental Temperature at 5 C Interrupting 100 amperes at 350V AC 100 amperes at 350V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Tape & Reel Quantity 500 pcs/reel Environmental Specification Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) 0.5A 0.75A 1A 1.5A A.5A 3A 4A 5A 6A 7A 8A 10A 1A Current in Amperes (A) Soldering Parameters CQ4PF 001 SERIES AMP Code Refer to Electrical

Type CQ4PT 6.1mmx.6mm (410) High Inrush Fuse Series Feature a. Chip Fuse structure design with PCB body and copper & tin alloy element b. Use optical lithography & etching skill to make refinement element c. Complete on element with the terminal electrode plating Tin material to prevent element oxidation. d. Product meet 100% ROHS, lead free, HF & REACH requirement. e. Offer range of current ratings from 0.5A-1A & voltage up to 350VAC and 350VDC. Material Construction Body Material: FR4 Board Termination Material: Copper(Cu),Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.850 0.160 CQ4PT.500 0.5A 500m A CQ4PT.750 0.75A 750mA 0.400 0.310 CQ4PT 001 1A 1A 0.067 0.450 CQ4PT 1.50 1.5 A 1.5 A 0.037 0.670 CQ4PT 00 A A 0.03 1.80 CQ4PT.50.5A.5A 0.018 1.810 CQ4PT 003 3 A 3 A 0.015.50 350V CQ4PT 004 4A 4A 0.011 4.000 CQ4PT 005 5A 5A 0.009 6.500 CQ4PT 006 6A 6A 0.007 9.000 CQ4PT 007 7A 7A 0.006 1.5 CQ4PT 008 8A 8A 0.005 14.7 CQ4PT 010 10A 10A 0.004 5.00 CQ4PT 01 1A 1A 0.003 36.00 Tape and Reel Specification Item W P E F P D D1 Criterion 1.00 4.00 1.75 5.50.00 1.50 1.00 Tolerence ±0.10 ±0.10 ±0.10 ±0.05 ±0.05 ±0.10 ±0.10 L1 L W 0.5A~1A 1.96.95 3.15 Reflow Solder Approval UL Recognized 0.5A~1A Electrical Characteristic Rated 1 ln ln.5 In 3 ln 8 In current MIN MIN MAX MAX MAX MAX 0.5A~1A 4 hr sec 60 sec 5 sec 3 sec 0.05 sec Environmental Temperature at 5 C Interrupting 100 amperes at 350V AC 100 amperes at 350V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Tape & Reel Quantity 500 pcs/reel Environmental Specification Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

Temperature Rerating Curve Average Time Current Curves Soldering Parameters CQ4PT 001 SERIES AMP Code Refer to Electrical

Type CQ1PF 3.1mmx 1.6mm (106) Fast-Acting Fuse Series Feature a. Chip Fuse structure design with PCB body and copper & tin alloy element b. Use optical lithography & etching skill to make refinement element c. Complete on element with the terminal electrode plating Tin material to prevent element oxidation. d. Product meet 100% ROHS, lead free, HF & REACH requirement. e. Offer range of current ratings from 0.5A-7A & voltage up to 63VDC and 63VAC. Material Construction Body Material: FR4 Board Termination Material: Copper(Cu),Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.10 0.033 CQ1PF.500 F 500m A CQ1PF.750 G 750mA 0.077 0.070 CQ1PF 001 H 1A 0.056 0.10 CQ1PF 1.50 K 1.5 A 0.034 0.60 CQ1PF 00 N A 0.05 0.440 CQ1PF.50 O.5A 63V 0.018 0.560 CQ1PF 003 P 3 A 0.014 0.990 CQ1PF 004 S 4A 0.011 1.440 CQ1PF 005 T 5A 0.008 1.750 CQ1PF 006 U 6A 0.007.340 CQ1PF 007 V 7A 0.006 3.430 Approval Tape and Reel Specification Item A B W E F P0 P1 P D0 T 10PS Criterion.000 0.050-0.050 3.500 0.050-0.050 8.000 0.100-0.100 1.750 0.050-0.050 3.500 0.050-0.050 4.000 0.100-0.100 4.000 0.100-0.100.000 0.050-0.050 Reflow Solder 1.550 0.050-0.050 0.950 0.050-0.050 40.000 0.100-0.100 Max.050 3.550 8.100 1.800 3.550 4.100 4.100.050 1.600 1.000 40.100 Min 1.950 3.450 7.900 1.700 3.450 3.900 3.900 1.950 1.500 0.900 39.900 UL Recognized 0.5A~7A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.5A~7A 4 hr 5 sec 0. sec Environmental Temperature at 5 C Interrupting 100 amperes at 63V AC 100 amperes at 63V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. 0.75 + 0.03mm Tape & Reel Quantity Environmental Specification 4000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) 0.5A 0.75A 1A 1.5A A.5A 3A 4A 5A 6A 7A Current in Ameres (A) Soldering Parameters CQ1PF 001 SERIES AMP Code Refer to Electrical

Type CQ1PT 3.1mmx 1.6mm (106) Slow Blow Fuse Series Feature a. Chip Fuse structure design with PCB body and copper & tin alloy element b. Use optical lithography & etching skill to make refinement element c. Complete on element with the terminal electrode plating Tin material to prevent element oxidation. d. Product meet 100% ROHS, lead free, HF & REACH requirement. e. Offer range of current ratings from 0.5A-7A & voltage up to 63VDC and 63VAC. Material Construction Body Material: FR4 Board Termination Material: Copper(Cu),Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.115 0.036 CQ1PT.500 F 500m A CQ1PT.750 G 750mA 0.075 0.076 CQ1PT 001 H 1A 0.053 0.135 CQ1PT 1.50 K 1.5 A 0.031 0.89 CQ1PT 00 N A 0.03 0.484 CQ1PT.50 O.5A 63V 0.016 0.855 CQ1PT 003 P 3 A 0.013 1.5 CQ1PT 004 S 4A 0.009 1.680 CQ1PT 005 T 5A 0.007.15 CQ1PT 006 U 6A 0.006.557 CQ1PT 007 V 7A 0.004 6.63 Approval Tape and Reel Specification Item A B W E F P0 P1 P D0 T 10P Criterion.000 0.050-0.050 3.500 0.050-0.050 8.000 0.100-0.100 1.750 0.050-0.050 3.500 0.050-0.050 4.000 0.100-0.100 4.000 0.100-0.100 Reflow Solder.000 0.050-0.050 1.550 0.050-0.050 0.950 0.050-0.050 40.000 0.100-0.100 Max.050 3.550 8.100 1.800 3.550 4.100 4.100.050 1.600 1.000 40.100 Min 1.950 3.450 7.900 1.700 3.450 3.900 3.900 1.950 1.500 0.900 39.900 S UL Recognized 0.5A~7A Electrical Characteristic Rated current 1 ln ln 3 ln 8 ln MIN MIN MAX MAX MAX 0.5A~7A 4 hr sec 10 sec 3 sec 0.05 sec Environmental Temperature at 5 C Interrupting 100 amperes at 63V AC 100 amperes at 63V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. 0.75 + 0.03mm Tape & Reel Quantity Environmental Specification 4000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

Temperature Rerating Curve Average Time Current Curves Soldering Parameters CQ1PT 001 SERIES AMP Code Refer to Electrical

Type CQ06PF 1.55mmx 0.8mm (0603) Fast-Acting Fuse Series Feature a. Chip Fuse structure design with PCB body and copper & tin alloy element b. Use optical lithography & etching skill to make refinement element c. Complete on element with the terminal electrode plating Tin material to prevent element oxidation. d. Product meet 100% ROHS, lead free, HF & REACH requirement. e. Offer range of current ratings from 0.5A-5A & voltage up to 63VDC and 63VAC. Material Construction Body Material: FR4 Board Termination Material: Copper(Cu),Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.145 0.030 CQ06PF.500 F 500m A CQ06PF.750 G 750mA 0.095 0.068 CQ06PF 001 H 1A 0.069 0.130 CQ06PF 1.50 K 1.5 A 0.04 0.60 CQ06PF 00 N A 63V 0.019 0.300 CQ06PF.50 O.5A 0.016 0.375 CQ06PF 003 P 3 A 0.013 0.540 CQ06PF 004 S 4A 0.010 1.040 CQ06PF 005 T 5A 0.008 1.65 Tape and Reel Specification Item A B W E F P0 P1 P D0 T 10P0 Criterion 1.080 0.00-0.030 1.880 0.00-0.030 8.000 0.100-0.100 1.750 0.050-0.050 3.500 0.050-0.050 4.000 0.050-0.050 4.000 0.050-0.050.000 0.050-0.050 Reflow Solder 1.550 0.050-0.050 0.600 0.030-0.030 40.000 0.100-0.100 Max 1.100 1.900 8.100 1.800 3.550 4.050 4.050.050 1.600 0.630 40.100 Approval Min 1.050 1.850 7.900 1.700 3.450 3.950 3.950 1.950 1.500 0.570 39.900 UL Recognized 0.5A~5A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.5A~5A 4hr 5 sec 0. sec Environmental Temperature at 5 C Interrupting 100 amperes at 63V AC 100 amperes at 63V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Tape & Reel Quantity Environmental Specification 5000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

Temperature Rerating Curve Average Time Current Curves Soldering Parameters CQ06PF 001 SERIES AMP Code Refer to Electrical

Type CQ06PT 1.55mmx 0.8mm (0603) Slow Blow Fuse Series Feature a. Chip Fuse structure design with PCB body and copper & tin alloy element b. Use optical lithography & etching skill to make refinement element c. Complete on element with the terminal electrode plating Tin material to prevent element oxidation. d. Product meet 100% ROHS, lead free, HF & REACH requirement. e. Offer range of current ratings from 0.5A-5A & voltage up to 63VDC and 63VAC. Material Construction Body Material: FR4 Board Termination Material: Copper(Cu),Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Dimension Recommended Land Pattern Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.13 0.034 CQ06PT.500 F 500m A CQ06PT.750 G 750mA 0.084 0.076 CQ06PT 001 H 1A 0.06 0.157 CQ06PT 1.50 K 1.5 A 0.040 0.93 CQ06PT 00 N A 63V 0.018 0.438 CQ06PT.50 O.5A 0.013 0.755 CQ06PT 003 P 3 A 0.011 0.765 CQ06PT 004 S 4A 0.008 1.50 CQ06PT 005 T 5A 0.005.375 Tape and Reel Specification Item A B W E F P0 P1 P D0 T 10P0 Criterion 1.080 0.00-0.030 1.880 0.00-0.030 8.000 0.100-0.100 1.750 0.050-0.050 3.500 0.050-0.050 4.000 0.050-0.050 4.000 0.050-0.050.000 0.050-0.050 Reflow Solder 1.550 0.050-0.050 0.600 0.030-0.030 40.000 0.100-0.100 Max 1.100 1.900 8.100 1.800 3.550 4.050 4.050.050 1.600 0.630 40.100 Approval Min 1.050 1.850 7.900 1.700 3.450 3.950 3.950 1.950 1.500 0.570 39.900 UL Recognized 0.5A~5A Electrical Characteristic Rated current 1 ln ln 3 ln 8 ln MIN MIN MAX MAX MAX 0.5A~5A 4 hr sec 10 sec 3 sec 0.05 sec Environmental Temperature at 5 C Interrupting 100 amperes at 63V AC 100 amperes at 63V DC Soldering Method *Reflow Soldering : 60 C, 30Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Tape & Reel Quantity Environmental Specification 5000 pcs/reel Operating Temperature -55 C to +15 C Thermal Shock MIL-STD-0G,Method 107,Condition B (-65 C to +15 C) Vibration MIL-STD-0G,Method 04,Test Condition C Moisture Resistance MIL-STD-0G,Method 106,10 day cycle Solderability IPC-J-STD-00C

Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) 0.5A 0.75A 1A 1.5A A.5A 3A 4A 5A Current in Amperes (A) Soldering Parameters CQ06PT 001 SERIES AMP Code Refer to Electrical

Z Type CF1 3.1mmx1.55mm (106) High-surge Enhanced Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 3.1 Recommended Land Pattern.0-.4 Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics 0.5 0.mm 1.55 0.1mm 0.60 ± 0.1 mm 1.-1.8 1.-1.8 Reflow Solder Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.590 0.0110 CF1V6TR50 F 0.50A CF1V6TR80 K 0.80A 0.5 0.0310 CF1V6T1R0 L 1.00A 0.130 0.0340 CF1V6T1R5 M 1.5A 63V DC 0.088 0.060 CF1V6T1R50 P 1.50A 0.065 0.1440 CF1V6TR0 S.00A 0.038 0.1810 CF1V3TR50 T.50A 0.03 0.3510 CF1V3T3R00 3 3.00A 0.03 0.5010 3V DC CF1V3T4R0 W 4.00A 0.015 0.9540 CF1V3T5R0 Y 5.00A 0.011 0.9660 CF1V3T7R0 7.00A 0.007 3.500 Approval Tape and Reel Specification Item A B W F E P P P 1 0 D0 T 3.6 8.0 3.5 1.75 4.0.0 4.0 +0.1.0 Criterion 0.84 ±0.15 ±0. ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion 178 60.0 13.0 9.0 11.4 ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity 5000 pcs/reel UL Recognized 0.5A~7A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.5A~7A 4hr 60sec 1 sec Environmental Temperature at 5 C Interrupting 0.5A~A : 50 amperes at 63V DC.5A~7A : 50 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With 10-55-10Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CF 1 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

Type CF06 1.6mmx 0.80mm (0603) High-surge Enhanced Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 1.6 Recommended Land Pattern 0.7-0.9 Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics 0.35 0.mm 0.80 0.1mm 0.45 ± 0.1 mm 0.8-1.0 0.8-1.0 Reflow Solder Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.496 0.0040 CF06V5TR40 E 0.40A 50V DC CF06V5TR50 F 0.50A 0.50 0.0050 CF06V3TR63 I 0.63A 0.173 0.0070 CF06V3TR80 K 0.80A 0.115 0.0140 CF06V3T1R0 L 1.00A 0.088 0.0160 CF06V3T1R5 M 1.5A 0.063 0.070 CF06V3T1R50 P 1.50A 0.045 0.0370 CF06V3T1R60 N 1.60A 0.04 0.0410 CF06V3TR0 S.00A 3V DC 0.033 0.0440 CF06V3TR50 T.50A 0.04 0.0550 CF06V3T3R00 3 3.00A 0.01 0.080 CF06V3T3R15 U 3.15A 0.019 0.0890 CF06V3T4R0 W 4.00A 0.015 0.390 CF06V3T5R0 Y 5.00A 0.01 0.4330 Tape and Reel Specification Item A B W F E P P P 1 0 D0 T Criterion 1.9 8.0 3.5 1.75 4.0.0 4.0 +0.1 1.1 0.64 ±0.1 ±0.1 ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion 178 60.0 13.0 9.0 11.4 ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity 5000 pcs/reel Approval UL Recognized 0.4A~5A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.4A~5A 4hr 60sec 1 sec Environmental Temperature at 5 C Interrupting 0.4A~0.5A : 50 amperes at 50V DC 0.63A~5A : 50 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With 10-55-10Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CF 04 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

Type CF04 1.0mmx 0.5mm (040) High-surge Enhanced Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 1.0 Recommended Land Pattern 0.5-0.6 Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics 0.5 0.05mm 0.35 ± 0.05mm 0.4-0.6 0.4-0.6 Reflow Solder Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.690 0.000 CF04V3TR315 D 0.315A CF04V3TR50 F 0.50A 0.30 0.003 CF04V3TR75 V 0.75A 0.140 0.0040 CF04V3TR80 K 0.80A 0.10 0.0053 CF04V3T1R0 L 1.00A 0.090 0.007 CF04V3T1R5 M 1.5A 0.067 0.0134 CF04V3T1R50 P 1.50A 3V DC 0.051 0.0136 CF04V3T1R60 N 1.60A 0.046 0.0167 CF04V3TR0 S.00A 0.033 0.0198 CF04V3TR50 T.50A 0.05 0.0376 CF04V3T3R00 3 3.00A 0.00 0.0543 CF04V3T3R15 U 3.15A 0.019 0.0530 CF04V3T4R0 W 4.00A 0.016 0.0900 Tape and Reel Specification Item A B W F E P P P 1 0 D0 T 1. 8.0 3.5 1.75.0.0 4.0 +0.1 0.7 Criterion 0.45 ±0.05 ±0.05 ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion 178 60.0 13.0 9.0 11.4 ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity 10000 pcs/reel Approval UL Recognized 0.315A~4A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.315A~4A 4hr 60sec 1 sec Environmental Temperature at 5 C Interrupting 0.315A~4A : 35 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With 10-55-10Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CF 04 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

Z Type CFS1 3.1mmx 1.55mm (106) Fast Acting Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 3.1 Recommended Land Pattern.0-.4 Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics 0.5 0.mm 1.55 0.1mm 0.60 ± 0.1 mm 1.-1.8 1.-1.8 Reflow Solder Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.385 0.0300 CFS1V6TR50 F 0.50A CFS1V6TR80 K 0.80A 0.165 0.0680 CFS1V6T1R0 L 1.00A 63V DC 0.108 0.0980 CFS1V6T1R5 M 1.5A 0.076 0.1550 CFS1V6T1R50 P 1.50A 0.051 0.360 CFS1V6TR0 S.00A 0.03 0.3390 CFS1V3TR50 T.50A 0.06 0.6050 CFS1V3T3R00 3 3.00A 0.00 0.9330 CFS1V3T4R0 W 4.00A 3V DC 0.014 1.5370 CFS1V3T5R0 Y 5.00A 0.010.5330 CFS1V3T7R0 7.00A 0.006 5.6840 Approval Tape and Reel Specification Item A B W F E P P P 1 0 D0 T.0 Criterion ±0.15 3.6 8.0 3.5 1.75 4.0.0 4.0 +0.1 0.84 ±0. ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion 178 60.0 13.0 9.0 11.4 ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity 5000 pcs/reel UL Recognized 0.5A~7A Electrical Characteristic Rated current 1 ln.5 ln 3 ln MIN MAX MAX 0.5A~7A 4hr 5sec 0. sec Environmental Temperature at 5 C Interrupting 0.5A~A : 50 amperes at 63V DC.5A~7A : 50 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With 10-55-10Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CFS 1 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

Type CFS06 1.6mmx 0.80mm (0603) Fast Acting Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 1.6 Recommended Land Pattern 0.7-0.9 Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics 0.35 0.mm 0.80 0.1mm 0.45 ± 0.1 mm 0.8-1.0 0.8-1.0 Reflow Solder Ampere Voltage Nominal Nominal Catalog Marking Resistance Melting I t Number [ In ] ( V ) Cold Ohms A Sec CFS06V5TR40 E 0.40A 0.350 0.0040 50V DC CFS06V5TR50 F 0.50A 0.175 0.0090 CFS06V3TR63 I 0.63A 0.130 0.0170 CFS06V3TR70 J 0.70A 0.148 0.030 CFS06V3TR80 K 0.80A 0.093 0.040 CFS06V3T1R0 L 1.00A 0.065 0.060 CFS06V3T1R5 M 1.5A 0.047 0.0570 CFS06V3T1R50 P 1.50A 0.036 0.0810 CFS06V3T1R60 N 1.60A 3V DC 0.034 0.0860 CFS06V3TR0 S.00A 0.06 0.1150 CFS06V3TR50 T.50A 0.00 0.000 CFS06V3T3R00 3 3.00A 0.016 0.100 CFS06V3T3R15 U 3.15A 0.015 0.790 CFS06V3T4R0 W 4.00A 0.01 0.360 CFS06V3T5R0 Y 5.00A 0.009 0.60 CFS06V3T6R0 6 6.00A 0.006.7000 Approval UL Recognized 0.4A~6A Electrical Characteristic Rated current 1 ln.5 ln 3 ln MIN MAX MAX 0.4A~6A 4hr 5sec 0. sec Environmental Temperature at 5 C Interrupting 0.4A~0.5A : 50 amperes at 50V DC 0.63A~6A : 50 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Tape and Reel Specification Item A B W F E P P P 1 0 D0 T Criterion 1.9 8.0 3.5 1.75 4.0.0 4.0 +0.1 1.1 0.64 ±0.1 ±0.1 ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion 178 60.0 13.0 9.0 11.4 ±.0 ±1.0 ±1.0 ±1.0 ±.0 Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With 10-55-10Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages Tape & Reel Quantity R<10% 5000 pcs/reel

Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CFS 1 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

Type CFS04 1.0mmx 0.5mm (040) Fast Acting Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 1.0 Recommended Land Pattern 0.5-0.6 Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics 0.5 0.05mm 0.35 ± 0.05mm 0.4-0.6 0.4-0.6 Reflow Solder Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.35 0.0037 CFS04V3TR50 F 0.50A CFS04V3TR80 K 0.80A 0.086 0.0095 CFS04V3T1R0 L 1.00A 0.064 0.0148 CFS04V3T1R5 M 1.5A 0.045 0.031 CFS04V3T1R50 P 1.50A 0.035 0.040 CFS04V3T1R60 N 1.60A 0.03 0.0374 CFS04V3TR0 S.00A 3V DC 0.04 0.0404 CFS04V3TR50 T.50A 0.019 0.0676 CFS04V3T3R00 3 3.00A 0.015 0.0986 CFS04V3T3R15 U 3.15A 0.014 0.1087 CFS04V3T4R0 W 4.00A 0.010 0.1145 Approval Tape and Reel Specification Item A B W F E P P P 1 0 D0 T 1. 8.0 3.5 1.75.0.0 4.0 +0.1 0.7 Criterion 0.45 ±0.05 ±0.05 ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion 178 60.0 13.0 9.0 11.4 ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity 10000 pcs/reel UL Recognized 0.5A~4A Electrical Characteristic Rated current 1 ln.5 ln 3 ln MIN MAX MAX 0.5A~4A 4hr 5sec 0. sec Environmental Temperature at 5 C Interrupting 0.5A~4A : 35 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With 10-55-10Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CFS 04 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

Z Type CP1 3.1mmx1.55mm (106) Fast Acting Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 3.1 Recommended Land Pattern.0-.4 Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics 0.5 0.mm 1.55 0.1mm 0.60 ± 0.1 mm 1.-1.8 1.-1.8 Reflow Solder Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.640 0.0150 CP1V6TR50 F 0.50A CP1V6TR80 K 0.80A 0.58 0.0400 CP1V6T1R0 L 1.00A 0.178 0.060 CP1V6T1R5 M 1.5A 63V DC 0.1 0.0940 CP1V6T1R50 P 1.50A 0.083 0.1410 CP1V6TR0 S.00A 0.057 0.850 CP1V3TR50 T.50A 0.044 0.4450 CP1V3T3R00 3 3.00A 0.033 0.6390 3V DC CP1V3T4R0 W 4.00A 0.0 1.1090 CP1V3T5R0 Y 5.00A 0.017 1.7100 CP1V3T7R0 7.00A 0.011 3.3000 Approval Tape and Reel Specification Item A B W F E P P P 1 0 D0 T 3.6 8.0 3.5 1.75 4.0.0 4.0 +0.1.0 Criterion 0.84 ±0.15 ±0. ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion 178 60.0 13.0 9.0 11.4 ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity 5000 pcs/reel UL Recognized 0.5A~7A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.5A~7A 4hr 60sec 1 sec Environmental Temperature at 5 C Interrupting 0.5A~A : 50 amperes at 63V DC.5A~7A : 50 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With 10-55-10Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

r Temperature Rerating Curve Average Time Current Curves 0.5A 0.8 A 1A 1.5A 1.5A A.5A 3A 4A 5A 7A 10 1 Time in Seconds (s) 0.1 0.01 0.001 0.1 1 10 100 Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CP 1 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

Type CP06 1.6mmx 0.80mm (0603) Fast Acting Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 1.6 Recommended Land Pattern 0.7-0.9 Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics 0.35 0.mm 0.80 0.1mm 0.45 ± 0.1 mm 0.8-1.0 0.8-1.0 Reflow Solder Ampere Voltage Nominal Nominal Catalog Marking Resistance Melting I t Number [ In ] ( V ) Cold Ohms A Sec CP06V5TR50 F 0.50A 50V DC 0.385 0.0088 CP06V3TR63 I 0.63A 0.18 0.0145 CP06V3TR80 K 0.80A 0.161 0.0178 CP06V3T1R0 L 1.00A 0.15 0.098 CP06V3T1R5 M 1.5A 0.085 0.0507 CP06V3T1R50 P 1.50A 0.066 0.0745 CP06V3T1R60 N 1.60A 0.063 0.0817 CP06V3TR0 S.00A 3V DC 0.045 0.1176 CP06V3TR50 T.50A 0.036 0.1807 CP06V3T3R00 3 3.00A 0.08 0.3517 CP06V3T3R15 U 3.15A 0.07 0.3805 CP06V3T4R0 W 4.00A 0.00 0.5746 CP06V3T5R0 Y 5.00A 0.016 0.776 Tape and Reel Specification Item A B W F E P P P 1 0 D0 T Criterion 1.9 8.0 3.5 1.75 4.0.0 4.0 +0.1 1.1 0.64 ±0.1 ±0.1 ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion 178 60.0 13.0 9.0 11.4 ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity 5000 pcs/reel Approval UL Recognized 0.5A~5A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.5A~5A 4hr 5sec 0. sec Environmental Temperature at 5 C Interrupting 0.5A :50 amperes at 50V DC 0.63A~5A : 50 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With 10-55-10Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CP 04 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

Type CP04 1.0mmx 0.5mm (040) Fast Acting Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 1.0 Recommended Land Pattern 0.5-0.6 Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics 0.5 0.05mm 0.35 ± 0.05mm 0.4-0.6 0.4-0.6 Reflow Solder Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.385 0.003 CP04V3TR50 F 0.50A CP04V3TR80 K 0.80A 0.161 0.0053 CP04V3T1R0 L 1.00A 0.15 0.007 CP04V3T1R5 M 1.5A 0.085 0.0134 CP04V3T1R50 P 1.50A 0.066 0.0135 CP04V3T1R60 N 1.60A 3V DC 0.063 0.0167 CP04V3TR0 S.00A 0.045 0.0198 CP04V3TR50 T.50A 0.036 0.0376 CP04V3T3R00 3 3.00A 0.08 0.054 CP04V3T3R15 U 3.15A 0.019 0.0630 CP04V3T4R0 W 4.00A 0.016 0.0896 Tape and Reel Specification Item A B W F E P P P 1 0 D0 T 1. 8.0 3.5 1.75.0.0 4.0 +0.1 0.7 Criterion 0.45 ±0.05 ±0.05 ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion 178 60.0 13.0 9.0 11.4 ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity 10000 pcs/reel Approval UL Recognized 0.5A~4A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.5A~4A 4hr 5sec 0. sec Environmental Temperature at 5 C Interrupting 0.5A~4A : 35 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With 10-55-10Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CP 04 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

Z Type CPS1 3.1mmx 1.55mm (106) Time-Lag Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 3.1 Recommended Land Pattern.0-.4 Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics 0.5 0.mm 1.55 0.1mm 0.60 ± 0.1 mm 1.-1.8 1.-1.8 Reflow Solder Catalog Number Marking Ampere [ In ] Voltage ( V ) Nominal Nominal Resistance Melting I t Cold Ohms A Sec 0.58 0.070 CPS1V6TR50 F 0.50A CPS1V6TR80 K 0.80A 0.15 0.070 CPS1V6T1R0 L 1.00A 63V DC 0.149 0.1340 CPS1V6T1R5 M 1.5A 0.100 0.330 CPS1V6T1R50 P 1.50A 0.071 0.3050 CPS1V6TR0 S.00A 0.047 0.5090 CPS1V3TR50 T.50A 0.039 0.7770 CPS1V3T3R00 3 3.00A 0.08 1.850 CPS1V3T4R0 W 4.00A 3V DC 0.019.5360 CPS1V3T5R0 Y 5.00A 0.015 5.5100 CPS1V3T7R0 7.00A 0.010 10.170 Approval Tape and Reel Specification Item A B W F E P P P 1 0 D0 T.0 Criterion ±0.15 3.6 8.0 3.5 1.75 4.0.0 4.0 +0.1 0.84 ±0. ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion 178 60.0 13.0 9.0 11.4 ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity 5000 pcs/reel UL Recognized 0.5A~7A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.5A~7A 4hr 10sec 0. sec Environmental Temperature at 5 C Interrupting 0.5A~A : 50 amperes at 63V DC.5A~7A : 50 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With 10-55-10Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CPS 1 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

Type CPS06 1.6mmx 0.80mm (0603) Time-Lag Fuse Series R Feature All high-density boards 100% lead-free RoHS and REACH compliant Low internal resistance Operating temperature range: -40 C to +15 C Dimension 1.6 Recommended Land Pattern 0.7-0.9 Small portable devices,mobile phone,pda etc. Digital products Game equipment LCD/LED monitors & modules(backlight inverter) Battery package Auto Electronics 0.35 0.mm 0.80 0.1mm 0.45 ± 0.1 mm 0.8-1.0 0.8-1.0 Reflow Solder Ampere Voltage Nominal Nominal Catalog Marking Resistance Melting I t Number [ In ] ( V ) Cold Ohms A Sec CPS06V5TR50 F 0.50A 50V DC 0.64 0.0090 CPS06V3TR63 I 0.63A 0.00 0.0140 CPS06V3TR80 K 0.80A 0.143 0.030 CPS06V3T1R0 L 1.00A 0.083 0.0360 CPS06V3T1R5 M 1.5A 0.054 0.0560 CPS06V3T1R50 P 1.50A 0.04 0.0810 CPS06V3T1R60 N 1.60A 3V DC 0.040 0.090 CPS06V3TR0 S.00A 0.08 0.1450 CPS06V3TR50 T.50A 0.0 0.90 CPS06V3T3R00 3 3.00A 0.018 0.330 CPS06V3T3R15 U 3.15A 0.016 0.3650 CPS06V3T4R0 W 4.00A 0.013 0.5740 CPS06V3T5R0 Y 5.00A 0.009 0.970 CPS06V3T6R0 6 6.00A 0.006 1.8600 Tape and Reel Specification Item A B W F E P P P 1 0 D0 T Criterion 1.9 8.0 3.5 1.75 4.0.0 4.0 +0.1 1.1 0.64 ±0.1 ±0.1 ±0. ±0.05 ±0.1 ±0.1 ±0.05 ±0.1-0 ±0.1 Item W T Criterion 178 60.0 13.0 9.0 11.4 ±.0 ±1.0 ±1.0 ±1.0 ±.0 Tape & Reel Quantity 5000 pcs/reel Approval UL Recognized 0.5A~6A Electrical Characteristic Rated current 1 ln ln 3 ln MIN MAX MAX 0.5A~6A 4hr 10sec 0. sec Environmental Temperature at 5 C Interrupting 0.5A : 50 amperes at 50V DC 0.63A~6A : 50 amperes at 3V DC Soldering Method *Refow Soldering : 60 C, 10Sec. max. *Wave Soldering : 60 C, 10Sec. max. *Hand Soldering : 350 C, 3Sec. max. Material Construction Body Material: Ceramic Termination Material:Tin(Sn) Fuse Element: Copper(Cu),Tin(Sn) Cover coat: Expoxy Environmental Specification Thermal Shock 10cycles of -40 C to +15 C Humidity 85±3 C; 85±5%RH;1000Hrs No mechanical damages Vibration With 10-55-10Hz/min;1.5mm;XYZdirection/hrs No mechanical damages Insulation Resistance 10,000 ohms or more after opening Resistance to soldering heat 60±5 C; 10±1 Sec No mechanical damages Solder ability 45±5 C; ±0.5 Sec 95% coverage minimum Terminal strength 10N;10Sec No mechanical damages R<10%

Temperature Rerating Curve Average Time Current Curves Time in Seconds (s) Current in Amperes (A) Soldering Parameters Reflow profile : (solder : Sn96.5 / Ag3 / Cu0.5) 5 Peak : 50, 5 sec 0 Pre heat Zone : 150 to 180, 90±30 sec Soldering Zone : 30 or higher, 30±10 sec CPS 1 V3 T 1R0 CF:High-surge Enhanced CFS: Fast acting CP:Fast acting CPS: Time-Lag 04:1.0x0.5mm 06:1.6x0.80mm 1:3.1x1.55mm VA:15V V6:63V V5:50V V3:3V T:Paper Tape 106/0603:5K 040:10K R50:0.50A 1R0:1.00A 1R50:1.50A R0:.00A R50:.50A 3R0:3.00A 5R0:5.00A 15R0:15.0A

PPTC SMD90 7.5mmx 5.5mm (90) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.90 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. d.operation Current: 0.30A~3.00A e.maximum Voltage: 6V~60V DC f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized 0.3A~3A TUV 0.3A~3A ANSI/J-std-00 Category 3 Tape & Reel Quantity 000 pcs/reel Electrical Characteristics(3 C) Part Number Hold Current Trip Current Rated Voltage Max Current Typical Max Time to Trip Resistance Power Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W A Sec Ohms Ohms SMD030-90-R 0.30 0.60 60 100 1.5 1.5 3.0 1.000 4.800 SMD050-90-R 0.50 1.00 60 100 1.5.5 4.0 0.300 1.400 SMD075-90-R 0.75 1.50 33 100 1.5 8.0 0.3 0.180 1.000 SMD075-60-90-R 0.75 1.50 60 10 1.5 8.0 0.3 0.180 1.000 SMD100-90-R 1.10.0 33 100 1.5 8.0 0.5 0.090 0.410 SMD15-90-R 1.5.50 33 100 1.5 8.0.0 0.050 0.50 SMD150-90-R 1.50 3.00 33 40 1.5 8.0.0 0.050 0.30 SMD185-90-R 1.85 3.70 33 40 1.5 8.0.5 0.040 0.150 SMD00-90-R.00 4.00 16 100 1.5 8.0 4.5 0.035 0.10 SMD00-4-90-R.00 4.00 4 40 1.5 8.0 5.0 0.035 0.10 SMD50-90-R.50 5.00 16 100 1.5 8.0 16.0 0.05 0.085 SMD60-90-R.60 5.0 6 100 1.5 8.0 0.0 0.00 0.075 SMD300-90-R 3.00 5.0 6 100 1.5 8.0 5.0 0.010 0.048 SMD300-15-90R 3.00 5.0 15 40 1.5 8.0 5.0 0.010 0.048 I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin

Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD030-90-R 6.73 7.98 4.80 5.44 0.60 1.15 0.50 1.0 0.50 0.90 SMD050-90-R 6.73 7.98 4.80 5.44 0.60 1.15 0.50 1.0 0.50 0.90 SMD075-90-R 6.73 7.98 4.80 5.44 0.40 1.15 0.50 1.0 0.50 0.90 SMD075-60-90-R 6.73 7.98 4.80 5.44 0.60 1.15 0.50 1.0 0.50 0.90 SMD100-90-R 6.73 7.98 4.80 5.44 0.40 1.00 0.50 1.0 0.50 0.90 SMD15-90-R 6.73 7.98 4.80 5.44 0.40 0.90 0.50 1.0 0.50 0.90 SMD150-90-R 6.73 7.98 4.80 5.44 0.40 0.90 0.50 1.0 0.50 0.90 SMD185-90-R 6.73 7.98 4.80 5.44 0.30 0.90 0.50 1.0 0.50 0.90 SMD00-90-R 6.73 7.98 4.80 5.44 0.30 0.90 0.50 1.0 0.50 0.90 SMD00-4-90-R 6.73 7.98 4.80 5.44 0.0 0.80 0.50 1.0 0.50 0.90 SMD50-90-R 6.73 7.98 4.80 5.44 0.30 0.90 0.50 1.0 0.50 0.90 SMD60-90-R 6.73 7.98 4.80 5.44 0.30 0.90 0.50 1.0 0.50 0.90 SMD300-90-R 6.73 7.98 4.80 5.44 0.40 0.90 0.50 1.0 0.50 0.90 SMD300-15-90R 6.73 7.98 4.80 5.44 0.65 1.15 0.50 1.0 0.50 0.90 Thermal Derating Curve Percent of Rated Hold and Trip Current 00% 150% 100% 50% Thermal Derating Curve, FSMD90 Series 0% -40-0 0 0 40 60 80 A= SMD15-90-R ~ SMD300-90-R B= SMD030-90 -R~ A B SMD100-90-R Ambient Temperature ( ) NOTE : Specification subject to change without notice.

Average Time Current Curves A = SMD030-90-R B = SMD050-90-R C = SMD075-90-R/ 075-60-90-R D = SMD100-90-R E = SMD15-90-R F = SMD150-90-R G = SMD185-90-R H = SMD00-90-R/ 00-4-90-R I = SMD50-90-R J = SMD60-90-R K= SMD300-90-R/ 300-15-90R Time-to-trip (S) 100 10 1 0.1 0.01 A B C D EFGHIJK 0.001 0.1 1 10 100 Fault Current (A) Soldering Parameters 3 6 A B C 90 5.10.30 5.60 SMD 100 4 90 R AMP Code Refer to Electrical Voltage

PPTC SMD181 4.5mmx3.mm (181) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.181 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. d.operation Current: 0.10A~3.00A e.maximum Voltage: 6V~60V DC f.temperature Range: -45 C to +85 C Electrical Characteristics(3 C) Part Number Hold Current Trip Current Material Approval UL Recognized 0.A~3A Tape & Reel Quantity 000 pcs/reel SMD010-R 0.10 0.30 60 100 0.8 8.0 0.00 1.600 15.00 SMD014-R 0.14 0.30 60 100 0.8 8.0 0.008 1.00 6.500 SMD00-R 0.0 0.40 30 100 0.8 8.0 0.00 0.800 5.000 SMD00-60-R 0.0 0.40 60 40 0.8 8.0 0.00 0.800 5.000 SMD030-R 0.30 0.60 30 40 0.8 8.0 0.100 0.00 1.750 SMD035-R 0.35 0.70 16 40 0.8 8.0 0.100 0.30 1.500 SMD035-30-R 0.35 0.70 30 40 0.8 8.0 0.10 0.30 1.500 SMD050-R 0.50 1.00 16 100 0.8 8.0 0.150 0.150 1.000 SMD050-30-R 0.50 1.00 30 100 0.8 8.0 0.150 0.150 1.000 SMD075-R 0.75 1.50 16 100 0.8 8.0 0.00 0.110 0.450 SMD075-4R* 0.75 1.50 4 40 1.0 8.0 0.00 0.110 0.90 SMD075-33R* 0.75 1.50 33 40 1.0 8.0 0.00 0.110 0.400 SMD110-R 1.10.0 8 100 0.8 8.0 0.300 0.040 0.10 SMD110-16-R 1.10.0 16 100 0.8 8.0 0.500 0.040 0.180 SMD110-4R* 1.10.0 4 100 1.0 8.0 0.500 0.060 0.00 SMD15-R 1.5.50 6 100 0.8 8.0 0.400 0.050 0.140 SMD15-16R 1.5.50 16 100 0.8 8.0 0.400 0.050 0.140 SMD150-R 1.50 3.00 8 100 0.8 8.0 0.500 0.040 0.110 SMD150-1R 1.50 3.00 1 100 1.0 8.0 0.500 0.040 0.110 SMD150-4R 1.50 3.00 4 100 1.0 8.0 1.500 0.040 0.10 SMD160-R 1.60 3.0 8 100 0.8 8.0 0.500 0.030 0.100 SMD160-1R 1.60 3.0 1 100 1.0 8.0 1.000 0.030 0.100 SMD160-16R 1.60 3.0 16 100 1.0 8.0 1.000 0.030 0.100 SMD00R.00 3.50 8 100 1.0 8.0.000 0.00 0.070 SMD60R.60 5.00 6 100 1.0 8.0.500 0.015 0.047 SMD60-13R*.60 5.00 13. 100 1.3 8.0 5.000 0.015 0.050 SMD60-16R*.60 5.00 16 100 1.3 8.0 5.000 0.015 0.050 SMD300R* 3.00 5.00 6 100 1.0 8.0 4.000 0.01 0.040 I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin Rated Voltage Max Current Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, ANSI/J-std-00 Category 3 TUV Typical 0.75A~3A Max Time to Trip Resistance * 1500 pcs/reel Power Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W Amp Sec Ohms Ohms

Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD010-R 4.37 4.73 3.07 3.41 0.60 0.90 0.30 0.95 0.5 0.65 SMD014-R 4.37 4.73 3.07 3.41 0.60 0.90 0.30 0.95 0.5 0.65 SMD00-R 4.37 4.73 3.07 3.41 0.60 0.90 0.30 0.95 0.5 0.65 SMD00-60-R 4.37 4.73 3.07 3.41 0.60 0.90 0.30 0.95 0.5 0.65 SMD030-R 4.37 4.73 3.07 3.41 0.40 0.70 0.30 0.95 0.5 0.65 SMD035-R 4.37 4.73 3.07 3.41 0.40 0.70 0.30 0.95 0.5 0.65 SMD035-30-R 4.37 4.73 3.07 3.41 0.40 0.70 0.30 0.95 0.5 0.65 SMD050-R 4.37 4.73 3.07 3.41 0.35 0.65 0.30 0.95 0.5 0.65 SMD050-30-R 4.37 4.73 3.07 3.41 0.45 0.75 0.30 0.95 0.5 0.65 SMD075-R 4.37 4.73 3.07 3.41 0.35 0.65 0.30 0.95 0.5 0.65 SMD075-4R 4.37 4.73 3.07 3.41 0.80 1.55 0.5 0.95 0.5 0.65 SMD075-33R 4.37 4.73 3.07 3.41 0.80 1.55 0.5 0.95 0.5 0.65 SMD110-R 4.37 4.73 3.07 3.41 0.5 0.55 0.30 0.95 0.5 0.65 SMD110-16-R 4.37 4.73 3.07 3.41 0.5 0.90 0.30 0.95 0.5 0.65 SMD110-4R 4.37 4.73 3.07 3.41 0.80 1.30 0.5 0.95 0.5 0.65 SMD15-R 4.37 4.73 3.07 3.41 0.5 0.55 0.30 0.95 0.5 0.65 SMD15-16R 4.37 4.73 3.07 3.41 0.50 1.00 0.30 0.95 0.5 0.65 SMD150-R 4.37 4.73 3.07 3.41 0.5 0.55 0.30 0.95 0.5 0.65 SMD150-1R 4.37 4.73 3.07 3.41 0.60 1.10 0.5 0.95 0.5 0.65 SMD150-4R 4.37 4.73 3.07 3.41 0.60 1.55 0.5 0.95 0.5 0.65 SMD160-R 4.37 4.73 3.07 3.41 0.5 0.90 0.30 0.95 0.5 0.65 SMD160-1R 4.37 4.73 3.07 3.41 0.60 1.35 0.5 0.95 0.5 0.65 SMD160-16R 4.37 4.73 3.07 3.41 0.60 1.35 0.5 0.95 0.5 0.65 SMD00R 4.37 4.73 3.07 3.41 0.55 1.0 0.5 0.95 0.5 0.65 SMD60R 4.37 4.73 3.07 3.41 0.55 1.0 0.5 0.95 0.5 0.65 SMD60-13R 4.37 4.73 3.07 3.41 0.80 1.55 0.5 0.95 0.5 0.65 SMD60-16R 4.37 4.73 3.07 3.41 0.80 1.55 0.5 0.95 0.5 0.65 SMD300R 4.37 4.73 3.07 3.41 0.80 1.55 0.5 0.95 0.5 0.65 NOTE : Specification subject to change without notice.

Thermal Derating Curve SMD Series Percent of Rated Hold and Trip Current 00% 150% 100% 50% 0% -40-0 0 0 40 60 80 Ambient Temperature ( ) A= SMD 075-R, 075-4R, 075-33R, 110-R, 110-16-R, 110-4R, 15-R, 15-16R, 150-R, 150-1R, 150-4R, 160-R, 160-1R, 160-16R, 00R, 60R, 60-13R, 60-16R,300R B= SMD010-R, 014-R, 00-R, 00-60-R, 030-R, 035-R,035-30-R,050-R, 050-30-R Average Time Current Curves A = SMD010-R B = SMD014-R C = SMD00-R / 00-60-R D = SMD030-R E = SMD035-R / 035-30-R F = SMD050-R / 050-30-R G = SMD075-R / 075-4R / 075-33R H = SMD110-R / 110-16-R / 110-4R I = SMD15-R / 15-16R J = SMD150-R / 150-1R / 150-4R K = SMD160-R / 160-1R / 160-16R L = SMD00R M = SMD60R / 60-13R / 60-16R N = SMD300R Time-to-trip (S) 100 10 1 0.1 SMD S eries A B C D E F G HIJ K LM N 0.01 0.001 0.1 1 10 100 Fault Current (A) NOTE : Specification subject to change without notice.

Soldering Parameters 3 6 A B C 181 3.45 1.78 3.50 SMD 100 4 R AMP Code Refer to Electrical Voltage

PPTC SMD110 3.mmx.5mm (110) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.110 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. Lower resistance than standard SMD devices. d.operation Current: 0.05A~.00A e.maximum Voltage: 6V~60V DC f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized 0.05A~A TUV 0.05A~A Tape & Reel Quantity ANSI/J-std-00 Category 3 3000 pcs/reel * 4000 pcs/reel Electrical Characteristics(3 C) Part Number Hold Current I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin Trip Current Rated Voltage Max Current Typical Max Time to Trip Resistance Power Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W A Sec Ohms Ohms SMD005-110-R 0.05 0.15 60 10 0.60 0.5 3.00 3.600 50.000 SMD010-110-R 0.10 0.5 60 10 0.60 0.50 1.50 1.600 15.000 SMD00-110-R 0.0 0.40 30 10 0.60 8.00 0.0 0.800 5.000 SMD035-110-R* * 0.35 0.70 16 100 0.60 8.00 0.0 0.30 1.300 SMD050-110-R * 0.50 1.00 16 100 0.60 8.00 0.10 0.50 0.900 SMD075-110-R * 0.75 1.50 8 100 0.60 8.00 0.10 0.130 0.400 SMD075-4-110R 0.75 1.50 4 100 0.60 8.00 0.10 0.130 0.400 SMD110-110R 1.10.0 6 100 0.80 8.00 0.30 0.060 0.10 SMD150-110R 1.50 3.00 6 100 0.80 8.00 0.50 0.040 0.110 SMD175-110R 1.75 4.00 6 100 0.80 8.00 0.60 0.00 0.080 SMD00-110R.00 4.00 6 100 0.80 8.00 1.00 0.015 0.070

Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD005-110-R 3.00 3.43.35.80 0.60 1.15 0.5 0.75 0.10 0.45 SMD010-110-R 3.00 3.43.35.80 0.60 1.15 0.5 0.75 0.10 0.45 SMD00-110-R 3.00 3.43.35.80 0.40 0.85 0.5 0.75 0.10 0.45 SMD035-110-R 3.00 3.43.35.80 0.40 0.80 0.5 0.75 0.10 0.45 SMD050-110-R 3.00 3.43.35.80 0.30 0.75 0.5 0.75 0.10 0.45 SMD075-110-R 3.00 3.43.35.80 0.30 0.70 0.5 0.75 0.10 0.45 SMD075-4-110R 3.00 3.43.35.80 0.90 1.30 0.5 0.75 0.10 0.45 SMD110-110R 3.00 3.43.35.80 0.60 1.00 0.5 0.75 0.10 0.45 SMD150-110R 3.00 3.43.35.80 0.50 0.90 0.5 0.75 0.10 0.45 SMD175-110R 3.00 3.43.35.80 0.80 1.40 0.5 0.75 0.10 0.45 SMD00-110R 3.00 3.43.35.80 0.80 1.40 0.5 0.75 0.10 0.45 Thermal Derating Curve 00% Thermal Derating Curve, SMD110 Series Percent of Rated Hold and Trip Current 150% 100% 50% 0% -40-0 0 0 40 60 80 Ambient Temperature ( ) NOTE : Specification subject to change without notice.

Average Time Current Curves A = SMD005-110 -R B = SMD010-110 -R C = SMD00-110 -R D = SMD035-110 -R E = SMD050-110 -R F = SMD075-110 -R/ 075-4-110R G = SMD110-110R H = SMD150-110R I = SMD175-110R J = SMD00-110R Time-to-trip (S) 100 10 A 1 0.1 B C D E F G H I J 0.01 0.001 0.1 1 10 100 Fault Current (A) Soldering Parameters 3 6 A B C 110.00 1.00.80 SMD 100 4 110 R AMP Code Refer to Electrical Voltage

PPTC SMD106 3.mmx 1.6mm (106) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.106 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. Lower resistance than standard SMD devices. d.operation Current: 0.05A~.00A e.maximum Voltage: 6V~60V DC f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized TUV 0.05A~A 0.05A~A Tape & Reel Quantity ANSI/J-std-00 Category 3 3000 pcs/reel * 4000 pcs/reel * * 000 pcs/reel Electrical Characteristics(3 C) Part Number Hold Current I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin Trip Current Rated Voltage Max Current Typical Max Time to Trip Resistance Power Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W A Sec Ohms Ohms SMD005-106-R 0.05 0.15 60 10 0.4 0.5 1.50 3.600 50.000 SMD010-106-R 0.10 0.5 60 10 0.4 0.50 1.00 1.600 15.000 SMD01-106-R 0.1 0.39 48 100 0.6 1.00 0.0 1.400 6.500 SMD016-106-R 0.16 0.45 48 100 0.6 1.00 0.30 1.100 5.000 SMD00-106-R 0.0 0.40 30 100 0.4 8.00 0.10 0.600.500 SMD05-106-R 0.5 0.50 16 100 0.6 8.00 0.08 0.550.300 SMD05-4-106-R 0.5 0.50 4 40 0.6 8.0 0.08 0.550.300 SMD035-106-R * 0.35 0.75 16 100 0.4 8.00 0.10 0.300 1.00 SMD035-30-106R * 0.35 0.75 30 40 0.6 8.00 0.10 0.300 1.00 SMD050-106-R * 0.50 1.00 8 100 0.4 8.00 0.10 0.150 0.700 SMD050-4-106R * 0.50 1.00 4 100 0.6 8.00 0.10 0.150 0.750 SMD075-106R 0.75 1.50 6 100 0.6 8.00 0.0 0.090 0.90 SMD075-16-106R 0.75 1.50 16 100 0.6 8.00 0.0 0.090 0.90 SMD100-106R 1.00 1.80 6 100 0.6 8.00 0.30 0.055 0.10 SMD110-106R 1.10.0 6 100 0.8 8.00 0.30 0.040 0.180 SMD150-106R * * 1.50 3.00 6 100 0.8 8.00 1.00 0.040 0.10 SMD00-106R * *.00 3.50 6 100 0.8 8.00 1.50 0.018 0.080

Dimensions Part Thermal Derating Curve A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD005-106-R 3.00 3.50 1.50 1.80 0.45 0.85 0.10 0.75 0.10 0.45 SMD010-106-R 3.00 3.50 1.50 1.80 0.45 0.85 0.10 0.75 0.10 0.45 SMD01-106-R 3.00 3.50 1.50 1.80 0.45 0.85 0.10 0.75 0.10 0.45 SMD016-106-R 3.00 3.50 1.50 1.80 0.45 0.75 0.10 0.75 0.10 0.45 SMD00-106-R 3.00 3.50 1.50 1.80 0.45 0.75 0.10 0.75 0.10 0.45 SMD05-106-R 3.00 3.50 1.50 1.80 0.45 0.75 0.10 0.75 0.10 0.45 SMD05-4-106-R 3.00 3.50 1.50 1.80 0.45 0.75 0.10 0.75 0.10 0.45 SMD035-106-R 3.00 3.50 1.50 1.80 0.45 0.75 0.10 0.75 0.10 0.45 SMD035-30-106R 3.00 3.50 1.50 1.80 0.90 1.30 0.5 0.75 0.10 0.45 SMD050-106-R 3.00 3.50 1.50 1.80 0.5 0.55 0.10 0.75 0.10 0.45 SMD050-4-106R 3.00 3.50 1.50 1.80 0.90 1.30 0.5 0.75 0.10 0.45 SMD075-106R 3.00 3.50 1.50 1.80 0.45 1.5 0.5 0.75 0.10 0.45 SMD075-16-106R 3.00 3.50 1.50 1.80 0.45 1.5 0.5 0.75 0.10 0.45 SMD100-106R 3.00 3.50 1.50 1.80 0.45 1.00 0.5 0.75 0.10 0.45 SMD110-106R 3.00 3.50 1.50 1.80 0.45 1.00 0.5 0.75 0.10 0.45 SMD150-106R 3.00 3.50 1.50 1.80 0.80 1.40 0.5 0.75 0.10 0.45 SMD00-106R 3.00 3.50 1.50 1.80 0.85 1.60 0.5 0.75 0.10 0.45 00% SMD106 Series Percent of Rated Hold and Trip Current 150% 100% 50% 0% -40-0 0 0 40 60 80 Ambient Temperature ( )

Average Time Current Curves Z= SMD005-106-R A= SMD010-106-R B= SMD01-106-R C= SMD016-106-R D= SMD00-106-R E= SMD05-106-R / 05-4-106-R F= SMD035-106-R / 035-60-106R G= SMD050-106-R / 050-4-106R H= SMD075-106R / 075-16-106R I= SMD100-106R J= SMD110-106R K= SMD150-106R L= SMD00-106R Time-to-trip (S) 100 10 Z 1 0.1 A B C D E F G H I J K L SMD106 Series 0.01 0.1 1 10 100 Fault current (A) Soldering Parameters 3 6 A B C 106.00 1.00 1.90 SMD 100 4 106 R AMP Code Refer to Electrical Voltage

PPTC SMD0805.0mmx 1.mm (0805) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.0805 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. Lower resistance than standard SMD devices. d.operation Current: 0.10A~1.00A e.maximum Voltage: 6V~15V f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized 0.10A~1A TUV 0.10A~1A Tape & Reel Quantity ANSI/J-std-00 Category 3 3000 pcs/reel * 4000 pcs/reel Electrical Characteristics(3 C) Part Number Hold Current I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin Trip Current Rated Voltage Max Current Typical Max Time to Trip Resistance Power Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W Amp Sec Ohms Ohms SMD010-0805-R * 0.10 0.30 15 100 0.5 0.50 1.50 0.700 6.000 SMD00-0805-R * 0.0 0.50 9 100 0.5 8.00 0.0 0.400 3.500 SMD035-0805-R * 0.35 0.75 6 100 0.5 8.00 0.10 0.50 1.00 SMD050-0805R 0.50 1.00 6 100 0.5 8.00 0.10 0.150 0.850 SMD050-9-0805R 0.50 1.00 9 100 0.5 8.00 0.10 0.150 0.850 SMD075-0805R 0.75 1.50 6 40 0.6 8.00 0.0 0.090 0.350 SMD100-0805R 1.00 1.95 6 40 0.6 8.00 0.30 0.060 0.10

Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD010-0805-R.00.30 1.0 1.50 0.30 1.00 0.0 0.60 0.10 0.45 SMD00-0805-R.00.30 1.0 1.50 0.30 1.00 0.0 0.60 0.10 0.45 SMD035-0805-R.00.30 1.0 1.50 0.5 0.75 0.0 0.60 0.10 0.45 SMD050-0805R.00.30 1.0 1.50 0.55 1.5 0.0 0.60 0.10 0.45 SMD050-9-0805R.00.30 1.0 1.50 0.55 1.5 0.0 0.60 0.10 0.45 SMD075-0805R.00.30 1.0 1.50 0.55 1.5 0.0 0.60 0.10 0.45 SMD100-0805R.00.30 1.0 1.50 0.75 1.80 0.0 0.60 0.10 0.45 Thermal Derating Curve SMD0805 Series 00% Percent of Rated Hold and Trip Current 150% 100% 50% 0% -40-0 0 0 40 60 80 Ambient Temperature ( ) NOTE : Specification subject to change without notice.

Average Time Current Curves 100 A B C D E F A = SMD010-0805-R B = SMD00-0805-R C = SMD035-0805-R D = SMD050-0805R / SMD050-9-0805R E = SMD075-0805R F = SMD100-0805R Time-to-trip (S) 10 1 0.1 0.01 0.1 1 10 Fault current (A) Soldering Parameters 3 6 A B C 0805 1.0 1.00 1.50 SMD 100 4 0805 R AMP Code Refer to Electrical Voltage

PPTC SMD0603 1.5mmx 0.8mm (0603) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.0603 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. Lower resistance than standard SMD devices. d.operation Current: 0.01A~0.0A e.maximum Voltage: 9V~60V DC f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized 0.05A~0.0A TUV 0.05A~0.0A Tape & Reel Quantity ANSI/J-std-00 Category 3 4000 pcs/reel Electrical Characteristics(3 C) Part Number Hold Current I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin Trip Current Rated Voltage Max Current Typical Power Max Time to Trip Resistance Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W A Sec Ohms Ohms SMD001-0603-R 0.01 0.03 60 40 0.5 0.0 1.00 15.00 100.00 SMD00-0603-R 0.0 0.06 60 40 0.5 0.0 1.00 1.00 70.00 SMD003-0603-R 0.03 0.09 30 40 0.5 0.0 1.00 6.00 50.00 SMD004-0603-R 0.04 0.1 4 40 0.5 0.0 1.00 4.00 40.00 SMD005-0603-R 0.05 0.15 15 40 0.5 0.50 0.10 3.80 30.00 SMD010-0603-R 0.10 0.5 15 40 0.5 0.70 0.10 0.90 8.00 SMD01-0603-R 0.1 0.30 9 40 0.5 0.80 0.10 1.10 5.80 SMD016-0603-R 0.16 0.40 9 40 0.5 1.00 0.10 1.00 4.0 SMD00-0603-R 0.0 0.45 9 40 0.5.00 0.10 0.55 3.50

Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD001-0603-R 1.40 1.80 0.45 1.00 0.35 0.85 0.10 0.50 0.08 0.40 SMD00-0603-R 1.40 1.80 0.45 1.00 0.35 0.85 0.10 0.50 0.08 0.40 SMD003-0603-R 1.40 1.80 0.45 1.00 0.35 0.75 0.10 0.50 0.08 0.40 SMD004-0603-R 1.40 1.80 0.45 1.00 0.35 0.75 0.10 0.50 0.08 0.40 SMD005-0603-R 1.40 1.80 0.45 1.00 0.35 0.75 0.10 0.50 0.08 0.40 SMD010-0603-R 1.40 1.80 0.45 1.00 0.35 0.75 0.10 0.50 0.08 0.40 SMD01-0603-R 1.40 1.80 0.45 1.00 0.35 0.75 0.10 0.50 0.08 0.40 SMD016-0603-R 1.40 1.80 0.45 1.00 0.35 0.75 0.10 0.50 0.08 0.40 SMD00-0603-R 1.40 1.80 0.45 1.00 0.35 0.75 0.10 0.50 0.08 0.40 Thermal Derating Curve 00% SMD0603 Series Percent of Rated Hold and Trip Current 150% 100% 50% 0% -40-0 0 0 40 60 80 Ambient Temperature ( ) NOTE : Specification subject to change without notice.

Average Time Current Curves A= SMD001-0603-R 100 A BCD E F GH I SMD0603 Series B= SMD00-0603-R C= SMD003-0603-R 10 D= SMD004-0603-R E= SMD005-0603-R F= SMD010-0603-R G= SMD01-0603-R H= SMD016-0603-R I= SMD00-0603-R Time-to-Trip (s) 1 0.1 0.01 0.001 0.01 0.1 1 10 Fault Current (A) Soldering Parameters 3 6 A B C 0603 0.80 0.60 0.80 SMD 100 0603 R AMP Code Refer to Electrical

PPTC LO RHO SMD181 4.5mmx 3.mm (181) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.181 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. Lower resistance than standard SMD devices. d.operation Current: 1.4A~3.7A e.maximum Voltage: 6V f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized 1.4A~3.7A TUV 1.4A~3.7A Tape & Reel Quantity ANSI/J-std-00 Category 3 000 pcs/tape Electrical Characteristics(3 C) Part Number Hold Current I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin Trip Current Rated Voltage Max Current Typical Max Time to Trip Resistance Power Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W A Sec Ohms Ohms SMD140RZ 1.40 3.60 6 100 1.0 8.0 3.00 0.010 0.035 SMD190RZ 1.90 4.90 6 100 1.0 8.0 5.00 0.003 0.05 SMD70RZ.70 6.0 6 100 1.0 13.5 3.00 0.003 0.03 SMD300RZ 3.00 7.00 6 100 1.0 15.0.00 0.003 0.0 SMD370RZ 3.70 9.10 6 100 1.0 18.5.00 0.003 0.018

Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD140RZ 4.37 4.73 3.07 3.41 0.30 0.70 0.5 0.95 0.5 0.65 SMD190RZ 4.37 4.73 3.07 3.41 0.30 0.70 0.5 0.95 0.5 0.65 SMD70RZ 4.37 4.73 3.07 3.41 0.40 0.75 0.5 0.95 0.5 0.65 SMD300RZ 4.37 4.73 3.07 3.41 0.40 0.75 0.5 0.95 0.5 0.65 SMD370RZ 4.37 4.73 3.07 3.41 0.40 0.75 0.5 0.95 0.5 0.65 Thermal Derating Curve Lo Rho SMD181 Series 00% Percent of Rated Hold and Trip Current 150% 100% 50% 0% -40-0 0 0 40 60 80 Ambient Temperature ( ) NOTE : Specification subject to change without notice.

Average Time Current Curves 100 Lo Rho SMD 181 Series A B CDE A = SMD140RZ B = SMD190RZ C = SMD70RZ D = SMD300RZ E = SMD370RZ Time-to-trip (S) 10 1 0.1 0.01 0.001 1 10 100 Fault Current (A) Soldering Parameters 3 6 A B C 181 3.45 1.78 3.50 AMP Code Refer to Electrical SMD 100 RZ

PPTC LO RHO SMD110 3.mmx.5mm (110) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.110 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. Lower resistance than standard SMD devices. d.operation Current: 1.75A~3.80A e.maximum Voltage: 6V f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized 1.75A~.00A TUV 1.75A~.00A Tape & Reel Quantity ANSI/J-std-00 Category 3 3000 pcs/tape * 4000 pcs/tape Electrical Characteristics(3 C) Part Number Hold Current I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin Trip Current Rated Voltage Max Current Typical Power Max Time to Trip Resistance Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W A Sec Ohms Ohms SMD175-110RZ * 1.75 3.50 6 100 1.0 8.00.50 0.006 0.040 SMD00-110RZ *.00 4.90 6 100 1.0 8.00 3.00 0.005 0.04 SMD300-110RZ 3.00 6.00 6 100 0.8 15.00.00 0.003 0.00 SMD350-110RZ 3.50 7.00 6 100 1.0 17.50.00 0.003 0.018 SMD380-110RZ 3.80 8.00 6 100 1.0 8.00 5.00 0.00 0.016

Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD 175-110RZ 3.00 3.43.35.80 0.40 0.75 0.5 0.75 0.10 0.45 SMD 00-110RZ 3.00 3.43.35.80 0.40 0.75 0.5 0.75 0.10 0.45 SMD 300-110RZ 3.00 3.43.35.80 0.60 1.00 0.5 0.75 0.10 0.45 SMD 350-110RZ 3.00 3.43.35.80 0.60 1.00 0.5 0.75 0.10 0.45 SMD 380-110RZ 3.00 3.43.35.80 0.60 1.00 0.5 0.75 0.10 0.45 Thermal Derating Curve 00% Lo Rho SMD110 series Percent of Rated Hold and Trip Current 150% 100% 50% 0% -40-0 0 0 40 60 80 Ambient Temperature ( ) NOTE : Specification subject to change without notice.

Average Time Current Curves Lo Rho SMD 110 series 100 A B C D E A= SMD175-110RZ B= SMD00-110RZ C= SMD300-110RZ D= SMD350-110RZ E= SMD380-110RZ Time-to-trip (S) 10 1 0.1 0.01 0.001 1 10 100 Fault Current (A) Soldering Parameters 3 6 A B C 110.00 1.00.80 AMP Code Refer to Electrical SMD 100 110RZ

PPTC LO RHO SMD106 3.mmx 1.6mm (106) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.106 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. Lower resistance than standard SMD devices. d.operation Current: 0.5A~.0A e.maximum Voltage: 6V f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized 0.5A~.0A TUV 0.5A~.0A Tape & Reel Quantity ANSI/J-std-00 Category 3 4000 pcs/tape Electrical Characteristics(3 C) Part Number Hold Current Trip Current Rated Voltage Max Current Typical Max Time to Trip Resistance Power Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W A Sec Ohms Ohms SMD050-106RZ 0.50 1.50 6 100 0.8 8.0 0.0 0.05 0.00 SMD075-106RZ 0.75 1.80 6 100 0.8 8.0 0.30 0.018 0.180 SMD110-106RZ 1.10.0 6 100 0.8 8.0 0.30 0.015 0.100 SMD150-106RZ 1.50 3.00 6 100 0.8 8.0 0.30 0.010 0.065 SMD00-106RZ.00 4.00 6 100 0.8 8.0 0.50 0.005 0.055 I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin

Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD050-106RZ 3.00 3.50 1.50 1.80 0.40 0.75 0.5 0.75 0.10 0.45 SMD075-106RZ 3.00 3.50 1.50 1.80 0.40 0.75 0.5 0.75 0.10 0.45 SMD110-106RZ 3.00 3.50 1.50 1.80 0.40 0.75 0.5 0.75 0.10 0.45 SMD150-106RZ 3.00 3.50 1.50 1.80 0.40 0.75 0.5 0.75 0.10 0.45 SMD00-106RZ 3.00 3.50 1.50 1.80 0.40 0.75 0.5 0.75 0.10 0.45 Thermal Derating Curve 00% Lo Rho SMD106 series Percent of Rated Hold and Trip Current 150% 100% 50% 0% -40-0 0 0 40 60 80 Ambient Temperature ( 0 C) NOTE : Specification subject to change without notice.

Average Time Current Curves A= SMD050-106RZ B= SMD075-106RZ C= SMD110-106RZ D= SMD150-106RZ E= SMD00-106RZ Time-to-trip (S) 100 10 1 0.1 0.01 A B C D E Lo Rho SMD 106 series 0.001 1 10 100 Fault Current (A) Soldering Parameters 3 6 A B C 106.00 1.00 1.90 AMP Code Refer to Electrical SMD 100 106RZ

PPTC LO RHO SMD0805.0mmx 1.mm (0805) Surface Mountable PTC Resettable Fuse R Feature a.rohs compliant & Halogen Free b.all high-density boards c.0805 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. Lower resistance than standard SMD devices. d.operation Current: 0.75A~1.75A e.maximum Voltage: 6V f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized 0.75A~1.5A TUV 0.75A~1.5A Tape & Reel Quantity ANSI/J-std-00 Category 3 4000 pcs/tape Electrical Characteristics(3 C) Part Number Hold Current Trip Current Rated Voltage Max Current Typical Power Max Time to Trip Resistance Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W A Sec Ohms Ohms SMD075-0805RZ 0.75 1.50 6 100 0.6 8.0 0.0 0.040 0.160 SMD110-0805RZ 1.10 1.80 6 100 0.6 8.0 0.30 0.030 0.130 SMD15-0805RZ 1.5.50 6 100 0.6 8.0 0.30 0.05 0.110 SMD150-0805RZ 1.50 3.00 6 100 0.6 8.0 0.30 0.015 0.065 SMD175-0805RZ 1.75 3.50 6 100 0.6 8.0 0.60 0.005 0.055 I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin

Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD 075-0805RZ.00.0 1.0 1.50 0.40 0.75 0.0 0.60 0.10 0.45 SMD 110-0805RZ.00.0 1.0 1.50 0.40 0.75 0.0 0.60 0.10 0.45 SMD 15-0805RZ.00.0 1.0 1.50 0.40 0.75 0.0 0.60 0.10 0.45 SMD 150-0805RZ.00.0 1.0 1.50 0.40 0.75 0.0 0.60 0.10 0.45 SMD 175-0805RZ.00.0 1.0 1.50 0.40 0.75 0.0 0.60 0.10 0.45 Thermal Derating Curve 00% Lo Rho SMD0805 series Percent of Rated Hold and Trip Current 150% 100% 50% 0% -40-0 0 0 40 60 80 Ambient Temperature ( 0 C) NOTE : Specification subject to change without notice.

Average Time Current Curves A = B = C = D = E = SMD075-0805RZ SMD110-0805RZ SMD15-0805RZ SMD150-0805RZ SMD175-0805RZ Time-to-trip (S) 10 1 0.1 A B C D E Lo Rho SMD 0805 series 0.01 1 10 100 Fault Current (A) Soldering Parameters 3 6 A B C 0805 1.0 1.00 1.50 AMP Code Refer to Electrical SMD 100 0805RZ

PPTC LO RHO SMD0603 1.5mmx 0.8mm (0603) Surface Mountable PTC Resettable Fuse Feature a.rohs compliant & Halogen Free b.all high-density boards c.0603 Dimension,Surface mountable,solid state,faster time to trip than standard SMD devices. Lower resistance than standard SMD devices. d.operation Current: 0.5A~0.75A e.maximum Voltage: 6~9V f.temperature Range: -45 C to +85 C Material Terminal Pad material: Pure Tin Soldering Characteristics: Meets EIA specification RS 186-9E, Approval UL Recognized pending TUV pending Tape & Reel Quantity ANSI/J-std-00 Category 3 4000 pcs/tape Electrical Characteristics(3 C) Part Number Hold Current Trip Current Rated Voltage Max Current Typical Max Time to Trip Resistance Power Current Time RMIN R1MAX IH, A IT, A VMAX, VDC IMAX, A Pd, W A Sec Ohms Ohms SMD05-0603RZ 0.5 0.55 9 100 0.5 8.0 0.08 0.500 3.000 SMD035-0603RZ 0.35 0.75 6 100 0.5 8.0 0.10 0.00 1.000 SMD050-0603RZ 0.50 1.00 6 100 0.6 8.0 0.10 0.070 0.350 SMD075-0603RZ 0.75 1.50 6 100 0.6 8.0 0.0 0.050 0.50 I H =Hold current-maximum current at which the device will not trip at 3 still air. IT=Trip current-minimum current at which the device will always trip at 3 still air. V MAX=Maximum voltage device can withstand without damage at it rated current.(i MAX) I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX). Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 3 still air environment. RMIN=Minimum device resistance at 3 prior to tripping. R1MAX=Maximum device resistance at 3 measured 1 hour after tripping or reflow soldering of 60 for 0 seconds. Termination pad characteristics Termination pad materials : Pure Tin

Dimensions Part A B C D E Number Min Max Min Max Min Max Min Max Min Max SMD05-0603RZ 1.40 1.80 0.45 1.00 0.35 0.75 0.10 0.50 0.08 0.40 SMD035-0603RZ 1.40 1.80 0.45 1.00 0.35 0.75 0.10 0.50 0.08 0.40 SMD050-0603RZ 1.40 1.80 0.45 1.00 0.35 0.75 0.10 0.50 0.08 0.40 SMD075-0603RZ 1.40 1.80 0.45 1.00 0.35 0.75 0.10 0.50 0.08 0.40 Thermal Derating Curve 00% Thermal Derating Curve, Lo Rho FSMD0603 series Percent of Rated Hold and Trip Current 150% 100% 50% 0% -40-0 0 0 40 60 80 Ambient Temperature ( ) NOTE : Specification subject to change without notice.

Average Time Current Curves 100 A B C D A = SMD05-0603RZ B = SMD035-0603RZ C = SMD050-0603RZ 10 D = SMD075-0603RZ Time-to-trip (S) 1 0.1 0.01 0.1 1 10 Fault Current (A) Soldering Parameters 3 6 A B C 0603 0.80 0.60 0.80 AMP Code Refer to Electrical SMD 100 0603RZ